Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
PRODUCT DATASHEETMinnie serieslast update 21/9/2012
Ordering number
FamilyTypeLEDColorDiameterHeightStyleOptic MaterialHolder MaterialFasteningStatus
C12095_MINNIE-M
MinnieReflectorMT-GMetal32.4 mm14.75 mmRound PC - Glue Ready
FWHMEfficiencycd/lmGerber File
26 degrees 92 % - Available
Ordering number
FamilyTypeLEDColorDiameterHeightStyleOptic MaterialHolder MaterialFasteningStatus
C11862_MINNIE-W
MinnieReflectorMT-GMetal32.4 mm14.75 mmRound PC - Glue Ready
FWHMEfficiencycd/lmGerber File
36 degrees 92 % - Available
Ordering number
FamilyTypeLEDColorDiameterHeightStyleOptic MaterialHolder MaterialFasteningStatus
C12097_MINNIE-WWW
MinnieReflectorMT-GMetal32.4 mm14.75 mmRound PC - Glue Ready
FWHMEfficiencycd/lmGerber File
74 degrees 90 % - Available
NOTE: The typical divergence will be changed by different color, chip size and chip positiontolerance. The typical total divergence is the full angle measured where the luminous intensityis half of the peak value.
February 21st 2013 18:17 Copyright Ledil Oy - Subject to change without prior notice - Page 1/2
Ledil Oy Salorankatu 10 24240 SALOFinland
http://www.ledil.com email: [email protected] FAX: +358-2-733 8001
PRODUCT DATASHEETMinnie serieslast update 21/9/2012
GENERAL INFORMATION
- Product series especially designed & optimized for MT-G series of LEDs. - Special care taken to make light distribution as uniform as possible.- Reflector is made of aluminium coated PC (120 degrees of Celcius / 248 degrees of Fahrenheit) withprotective lacquer (110 degrees of Celcius / 230 degrees of Fahrenheit).
- Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glueoptions.http://www.ledil.com/datasheets/DataSheet_GLUES.pdf
NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the endproduct. For example, mechanical stress, vibration and holes on the surface of the circuit boarweaken the strength of the glue.
NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. Ifcleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LEDmanufacturer -this is important as cleaning shall under no circumstances damage LEDs or otherelectronics components on the PCB.
Further note that optical components shall not be cleaned with any chemicals - only micro fibercloth may be used to remove fingerprints or other traces from handling.
February 21st 2013 18:17 Copyright Ledil Oy - Subject to change without prior notice - Page 2/2
Ledil Oy Salorankatu 10 24240 SALOFinland
http://www.ledil.com email: [email protected] FAX: +358-2-733 8001
0%
25%
50%
75%
100%
-50-40-30-20-1001020304050
Relative intensity of C12095_MINNIE-M / CA12239_MINNIE-M
0 %
25 %
50 %
75 %
100 %
-60-50-40-30-20-100102030405060
Relative intensity of Minnie-W-MTG
0%
25%
50%
75%
100%
-60-50-40-30-20-100102030405060
Relative intensity of CA12240_Minnie-WWW-MTG-assy
AD
BC AD
32
3
2
41
4
1
DESIGNED BYhh
DATE01.01.2011
CHECKED BYhh
DATE
DRAWN BY DATE
This drawing is our property.It can't be reproducedor communicated withoutour written agreement.
SCALE 1:1 WEIGHT(g) SHEET 1/1
SIZE
A4DRAWING NUMBER REV
DRAWING TITLE
Datasheet Minnie MT-G reflector
Material: PC
Coating: metal coating with clear laquer
ah1.6.2012
xx 2
Ledil Oy
Salorankatu 10
FIN-24100 SALO
Finland
14.75
0.9
12.8
Front view
0.43
distance between LED and bottom
32.4
12.8
Top view