Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
PRODUCT CATALOGUE
PSC Corporation
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Manufacturing & Sales Products
Filtration Equipment- Filtration System Engineering- Cartridge Filter :
Wound Depth Cartridge, Resin Bonded Fiber Cartridge,Binder-free Cartridge, Pleated Paper Cartridge,Metallic Cartridge (Cylindrical & Pleated Type),Ceramic Cartridge, Membrane Cartridge
- Sintered Metal Filter : Multi-Layer sintered, Fiber metal sintered,Powder metal sintered
- Candle Filter- Bag Filter- Activated Carbon Filter System
Coaleacer / Separator- Liquid-liquid Coalescer- Liquid-gas Coalescer- Oily Water Separator
Mist Eliminator- Vane Type Eliminator- Pad/demister Type Eliminator- Cartridge Type Eliminator
Strainer- Forged Strainer- Casting Strainer- Steel Welded Strainer- Self-cleaning Strainer- Auto-cleaning Strainer
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
PSC Model Category
No. Section Model No. Detailed Item
1 Metallic Filter Cartridge
PS Powder Sintered Filter Cartridge
MS Multi-Layer Sintered Filter Cartridge
FS Fiber Sintered Filter Cartridge
WS Woven Wire Screen Filter Cartridge
2 Filter Housing
JS,JF,JL,JE Cartridge Filter Housing
JP Gas Filter Housing
JG,JB Bag Filter Housing
3 Coalescer / Separator
LLC, GLC Coalescer / Separator
MME, STV, DPV Mist Eliminator
4 Filter System
JW Activated Carbon Filter System
- Auto Control Filter System
5 Auto-CleaningStrainer
JA-B Brush Cleaning Type,Auto-Cleaning Strainer
JA-R Rotating Arm Type,Auto-Cleaning Strainer
6 Strainer
JB-120, JB-130,JB-140, JB-150 Bucket Type Strainer
JY-200, JY-210,JY-220, JY-230 Y-Type Strainer
JT-310, JT-320, JT-330 T-Type Strainer
JC-410, JC-420 Temporary Strainer
JD-500 Duplex Type Strainer
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Basic Check Point When Designing Filter
Filter Housing Material- Carbon Steel, Stainless Steel 304, 316, Hastelloy, Nickel Alloy and etc.
Applicable Design Code- ASME Sec. VIII Div.1, JIS B 8243, KS B 6231
Cover Opening Type- Stud Bolt & Nut with Davit- Swing Bolt & Eye Nut with Hinge- Swing Bolt & Eye Nut with Davit- Quick Opening Closure- Hydraulic Cover Lift
Operation Condition (Minimum information when ordering)- Design Pressure : Kg/㎠.G, psid, bar-g, etc. - Operating Pressure : Kg/㎠.G, psid, bar-g, etc.- Design Temperature : ℃, ℉- Operating Temperature : ℃, ℉- Flow Rate : ㎡/hour, gpm, cfm, etc.- Filtration Rating : ㎛, #mesh, mm, inch, etc.- Fluid Name : Water, Oil, Compressed Air, Hydrogen Amine, etc.- Specific Gravity or Density : kg/㎡, kg/liter, etc.- Connection Size & Rating : ANSI, KS, JIS, AWWA, MSS, etc.- Operating Mode : Batch or continuous- Purpose to use filter- Pollution concentration
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Check Point When Selecting Filter
Initial Pressure Drop- The lower initial pressure drop, the longer change cycle of element(The optimum design must be considered the comparison of Economic
Efficiency of some costs for initial installation, maintenance and repair.)
Removal Rating of Element- According to use purpose, as there are various elements, it must be selected whether pollution particle is nominal rating or absolute rating. In case of the same shape, the relative superiority become clear comparing Beta Ratio
Five points of performance decision of filter is simply summarized in the following Darcy’s rule
A – filtration areaQ – Flow rateP – Pressure Dropμ – ViscosityR – Media Resistance
If flow rate Increases, pressure drop also increases. If flow rate increases, filtration area becomes wider. If viscosity becomes high, flow rate is decreased. If media resistance becomes high, flow rate also is decreased
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
METALLIC FILTER CARTIDGE
PSC Corporation
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Metallic Filter Cartridge
Advantages of PSC Metallic Filter Cartridge- It is advantageous in the side of life and protection of Environment as
it is possible to re-use after cleaning or reverse cleaning comparing
existed cartridge
- It is beneficial in the super-low temperature, high temperature and high
pressure
- It maintains absolute ratio of filtration
- The ratio of porous is very high
- Pressure loss is very low
The use ranges of PSC Metallic Filter Cartridge- Filtration of medical process
- Filtration of process for food and drink
- Filtration of process for atomic power generation and industry
- Filtration of process for petrochemical and refinery
- Filtration of gas and operating of oil pressure
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Ordering Information
1 Media Form PS = Powder Sintered, MS = Multi-Layer Woven Wire SinteredFS = Fiber Metal Sintered, WS Woven Wire Screen
2 Cartridge Type C = Cylindrical, P = Pleated
3 Removal Grade Model No. according to Series
4 Cartridge Length 10 = 10” (250), 20 = 20” (500), 30 = 30” (750)40 = 40” (1,000), CL=Special Custom Ordered-Consult Factory
5 Outer Diameter V = 2 3/8” (60), W = 2 ½” (63), X = 2 9/16” (65)Y = 2 ¾” (70), Z = Special Custom Ordered
6 Inner Diameter A = 1” (25), B = 1 ½” (37.5), C = Special Custom Ordered
7 Materials1 = SS304, 2 = SS304L, 3 = SS316, 4 = SS316L,5 = Special Custom Ordered : 300/400 Series SS, Copper Alloy, Nickel Alloy, Titanium, Alloy 20 and etc.
8 End Connection
DOE : Double Open Ends, Flat Gasket SealNPT : NPT Single Open EndSDE : Double O-ring Single Open EndSO : Single Open EndSPE : Special Custom Ordered
Gasket- V : Viton- E : Ethylene Propylene Rubber- NA : Natural Rubber- T : Teflon- No Symbol : Buna-N (Standard)
PS C 002 – 10 V A 1 DOE/V1 2 3 4 5 6 7 8
PSC Corporation
PS Series
Feature Porousness is uniformed as it becomes sintered
forming with regular particle Filtration efficiency is high because it is depth type
to pile up pollution material in the twisted windingly flow passage Durability and conservation capacity for filtration
particle of medium is excellent as it is formed by the sintered method of powder metal It can be used in lots of usage as it produced by
various material, SS304L, 316L, Inconel, Monel, Hastelloy, Alloy 20, and Titanium and etc. to have excellent corrosion resistance It is semi-permanent and regeneration effect is
high with reverse-cleaning and supersonic cleaning method as the washing rate is excellent with high washing rate The application limit of temperature is wide range
from super-low-temperature to high-temperature of 926 ℃ It can endure the high-pressure-drop and can be
applied to high pressure as it has high burst and collapse pressure
Filter Cartridge for Powder Metal SinteredPowder Sintered Media
Porous media is produced by diffusional sintered bond of powder metal
Powder Sintered MediumLiquid Rating : 2 micron absolutePorosity : 35%Flow (H,O) : 2gpm/ft2 at 0.5 psidContaminant Capacity : 0.7g/ft2 at 0.5 psid
Type Model
No.
Removal Rating (㎛)Liquid Gaseous
Nominal Absolute Nominal Absolute
Cylin
dric
al
PS 0002 0.2 2 0.01 0.1PS 0005 0.5 5 0.1 0.5PS 0020 2 9 0.5 1PS 0050 5 13 1 1.5PS 0100 10 20 2 3PS 0200 20 35 5 10PS 0400 40 55 10 20PS 1000 100 120 30 50
0.2㎛ (x100) 0.5㎛ (x100) 5 ㎛ (x100) 20 ㎛ (x100) 100 ㎛ (x100)
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, KoreaPSC Corporation
MS Series
Feature It is a metal net to be weaved at regular intervals and maintains the uniform pore, as it became sintered forming The choice range of filtration granularity is wideMedia production is possible as it adjusted the join order of metal net according to usage Treatment is easy and there is no need for a supporting or reinforcing structure as it is solid It is advantageous in an application of high-temperature and corrosion resistance is excellent as it is made by a raw material such as SS304, SS304L, SS316, SS316L It can endure a high-pressure-drop and is advantageous to a high-pressure as it has a high-burst and a collapse pressure It is semi-permanent and regeneration effect is high with a super sonic wash or reverse-wash
Filter Cartridge for Multi-Layer Metal SinteredMulti-Layer Sintered Media
This media is produced through Multi-Layer Diffusion Sintered Bond of Woven Wire Screen to be woven by metal wire in order of support layer, distribution layer, filtration layer and protection layer
Type Model
No.
Removal Rating (㎛)Liquid Gaseous
Nominal Absolute Nominal Absolute
Cylin
dric
al
MS 002A 2 10 0.5 1MS 005A 5 13 1 1.5MS 010A 10 17 1.5 2MS 015A 15 25 3 5MS 025A 25 40 6 12MS 033A 33 55 9 18MS 044A 44 70 20 40MS 061A 61 100 100 85MS 074A 74 120 120 90MS 104A 104 150 150 120MS 140A 140 200 200 175
PROTECTION LAYER
FILTRATION LAYER
DISTRIBUTION LAYER
SUPPORT LAYER
SUPPORT LAYER 90°
Woven Wire Cloth LaminateLiquid Rating : 10 micron absolutePorosity : 35%Flow (H,O) : 2gpm/ft2 at 0.5 psidContaminant Capacity : 0.7g/ft2 at 0.5 psid
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, KoreaPSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
WS Series
Filter Cartridge for Woven Wire ScreenWoven Wire Screen Media
It has feature and merit of each form and there are woven wire screen of various type according to weaving method of a metal wire as following pictures
Type Model
No.
Removal Rating (㎛)
Liquid GaseousNominal Absolute Nominal Absolute
Cylin
dric
al,
Plea
ted
WS 005 5 12 5 10
WS 010 10 17 10 15
WS 020 20 25 20 20
WS 035 35 48 35 40
WS 045 45 58 45 50
WS 060 60 73 60 65
WS 075 75 95 75 80
WS 100 100 120 100 90
WS 250 250 275 250 200
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
FS Series
Feature Filtration effect is high as a fiber metal of delicate denia type is sintered Conservation ability of filtration particle is excellent Life span is long as a heaping capacity for pollution material is big Cartridge production of pleated type is possible as the material thickness is thin Application Range of fluid and gas is wide and the corrosion resistance is excellent as it possible to produce by various materials such as SS304L, 316L, Inconel, Monel, Hastelloy, Alloy 20, and Titanium and etc. It is semi-permanent and regeneration effect is high with a super-sonic wash or reverse-wash as permeability is high and wash is excellent
Filter Cartridge for Fiber Metal SinteredMedia for Fiber Metal Sintered
This media is produced by Diffusional Sintered Bond with a mat type of a fibermetal of delicate denia
Fiber Metal MediumLiquid Rating : 3 micron absolutePorosity : 60%Flow (H,O) : 8gpm/ft2 at 0.5 psidContaminant Capacity : 2.2g/ft2 at 0.5 psid
Type Model
No.
Removal Rating (㎛)
Liquid Gaseous
Nominal Absolute Nominal Absolute
Cylin
dric
al,
Plea
ted
FS 001A 1 3 0.3 1
FS 003A 3 5 0.6 1.7
FS 005A 5 10 1 2.9
FS 010A 10 15 3 9
FS 025A 25 35 8 19
FS 030A 30 40 10 30
FS 070A 70 105 100 85
FS 140A 140 225 200 150
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Cartridge Filter Housing
JS TYPE JF TYPEStandard ModelIt is possible to design for special case also such as high-pressure, high-temperature according to condition of field use
JL TYPE JE TYPE
INLET
OUTLET
OUTLET
INLET
It is used a lot as automatic reverse-wash equipment, because it is easy to release pollution materialHeaping capacity of pollution material is bigIt can gain better filtration efficiency when filtering gas
Coated & Lined Housing- Rubber, Teflon, Polypropylene, FRP
INLET
OUTLET
It is possible to wash to every corner of internal housingMembrane Filter Cartridge is installed generallyThe main application is for food, manufacturing medicine and semiconductor company
INLET OUTLET
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JS – 40 - 31 2 3
Cartridge Filter Housing
1 Filter Housing Design Type
2 Filter Cartridge Quantity
3 Filter Cartridge Length (1=10” ~ 4=40”)
INLET
OUTLET
A
B
E
CD
E
BCD G
Model No.Flow Rate(㎡/HR)(Note 1)
In/Out Pipe Size
Mm(Inch)A B C D E F G
Weight(kg)
Carbon Steel Standard
JS 3-2 5-8 40A(1 1/2B) 200 870 450 620 1070 500 190 100JS 6-2 12-18 50A(2B) 250 900 480 620 1070 550 190 140JS 12-3 25-35 75A(3B) 350 1160 520 860 1380 650 280 210JS 19-3 40-70 100A(4B) 450 1220 640 860 1930 750 380 300JS 27-3 60-90 100A(4B) 500 1250 640 860 1960 800 420 350JS 33-3 80-120 125A(5B) 550 1240 660 880 2020 850 480 420JS 40-3 100-150 150A(6B) 600 1300 710 890 2100 960 520 500JS 50-3 130-180 150A(6B) 700 1330 740 890 2320 1110 680 730JS 60-3 150-200 200A(8B) 750 1370 830 890 2320 1110 680 730JS 80-3 220-300 200A(8B) 8001 370 830 890 2320 1160 730 850JS 100-3 300-400 250A(10B) 900 1460 930 930 2410 1300 830 1000JS 150-3 450-550 300A(12B) 1100 1510 1060 960 2670 1500 1030 1200JS 200-3 550-700 300A(12B) 1250 1590 1080 960 2720 1650 1180 1500* Note 1) Flow rate is by a pipe Caliber
Dimensions (mm) Cartridge Out Diameter 63mm StandardDesign Pressure 10K.f/ ㎠, #150)Standard
F
`̀̀
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Gas Filter Housing (Typical Redial Fin Element)
It is possible to design for Liquid type as the same type, also Filtration area is wide to adopt a Filter Element of pleated type Internal structure of Housing became to be able to maximize the heaping quantity of pollution material
ELEMENT STYLE JP06 – JP20 JP16 – JP30
The Pressure loss is very few as outlet and element is a direct connection type.
Filter Element
- Material : Polyester
Fiber Glass, Rayon, Nomex
Teflon and etc.
- Pore Size : 0.1 ~ 750 μ
Filter Housing
- Material : Carbon Steel, SS304, SS316
and etc.
- Design Code : ASME Sec. VIII, Div.1,
JIS B 8243, KS B 6231
INLETOUTLET
INLET OUTLET
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JP – 12 - 24 - 21 2 3 4
1 Filter Housing Design Type
2 Filter Element Diameter (Inch)
3 Filter Element Height (Inch)
4 Filter Element Quantity
Model No.Flow Rate(㎡/HR)(Note 1)
In/Out Pipe Size
Mm(Inch)A B C D E F
Weight(kg)
Carbon Steel Standard
JP 03-08-1 70 25(1B) 100 300 300 600 400 400 30JP 04-12-1 160 40A (1 1/2B) 150 350 420 770 450 150 45JP 06-12-1 280 50A(2B) 200 450 450 900 500 200 80JP 06-18-1 630 80A(3B) 200 450 600 1050 500 200 90JP 08-24-1 1150 100A(4B) 250 480 800 1280 550 180 135JP 10-24-2 3000 150A(6B) 300 500 1420 1920 600 230 200JP 12-24-2 4800 200A(8B) 400 540 1520 2480 760 330 310JP 16-24-2 7300 250A(10B) 500 540 1680 2850 860 430 420JP 20-24-2 11500 300A(12B) 600 710 1820 3650 960 530 680JP 24-24-2 14000 350A(14B) 700 740 1980 3880 1060 630 750JP 26-24-3 18500 400A(16B) 800 830 2220 3940 1300 730 960JP 30-24-3 31500 500A(20B) 900 930 2550 4120 1400 830 1120
1.03 (T+273)(P+1.03) 273
Dimensions (mm) Pore Size : 10 ㎛ StandardDesign Pressure 10K.f/ ㎠, #150)Standard
Gas Filter Housing (Typical Redial Fin Element)
A C D
B
BCD F
A C D
BBCD F
OUTLET OUTLETINLET INLET
2) CMH=SCMH x
(T=℃, P=kg/㎠)
* Note 1) Operating Pressure 7kg/㎠ @ 15℃Pressure Drop 0.5 psid (0.35kg/㎠)
E E
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Bag Filter Housing
Easy replacement of bags
Installation height is low
It is possible to adjust high and low
Mainly, it is used to small type
JG Type
Perfect sealing
Mainly, it is used to a big size
It is advantageous in case that the pipe
height is low as inlet pipe is same level with
outlet pipe
When a bag of the same quantity is installed, the shell diameter is smaller than JG type
An installation height is higher than JG type
JB Type
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JB – 4 - 11 2 3
1 Bag Housing Design Type
2 Bag Quantity
3 Bag Size (1=7”Φ x 18”l, 2=7”Φ x 32”l)
Model No.Flow Rate(㎡/HR)(Note 1)
In/Out Pipe Size
Mm(Inch)A B C D E F G
Weight(kg)
Carbon Steel Standard
JB 11 14-18 50A(2”) 200 520 400 370 720 500 190 80
JB 12 14-18 50A(2”) 200 870 400 720 1070 500 190 85
JB 31 30-40 80A(3”) 450 870 400 700 1580 750 380 210
JB 32 70-80 100A(4”) 450 1220 450 1050 1930 750 380 230
JB 41 70-80 100A(4”) 500 900 450 700 1610 800 420 300
JB 42 80-100 100A(4”) 500 1280 450 1050 1960 800 420 340
JB 72 120-150 150A(6”) 650 1280 500 1100 2130 1010 570 480
JB 112 200-250 200A(8”) 850 1420 600 1250 2350 1210 780 760
JB 142 250-350 250A(10”) 1200 1560 750 1320 2680 1600 1130 1350
* Note 1) The flow rate is a thing by inlet size
Dimensions (mm) Design Pressure 10K.f/ ㎠, #150)Standard
Bag Filter Housing
F
E
B
D
BCD G
A
F
C
BCD G
E
D
B
A
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
COALESCER | SEPARATOR
PSC Corporation
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Coalescer / Separator
Coalescer/Separator is an equipment to separate material of two liquid types not to be able to mix through a method of deposition or stabilization in a process to extract solvent in a petrochemical plant or in a process to refine petroleum in the refinery plant
PSC can supply, manufacture and design Coalescer/Separator to guarantee optimum performance from customer requirement and accumulated Know-How that is based on an experience of production and design for many years
There are following some kinds of Coalescer/Separator according to material to want to separate or fluid to be applied
1) Liquid/Liquid Coalescer2) Liquid/Gas Coalescer3) Oily Water Separator
It is possible to manufacture Vane Type, Cartridge Type, Pad Type, Double Stage, Single Stage, Level Type and Vertical Type according to shape or arrangement of element to be used.
Feature of PSC Coalescer/Separator1) Low Pressure Drop2) Various applicable range3) Complete separation4) Compact Design5) Simple and easy Maintenance
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
PSC Coalescer / Separator
JC1 Vertical Type, Two Stage Cartridge JC5 Vertical Type, Pad Type
JC2 Level Type, Cartridge JC6 Level Type, Pad Type
JC3 Vertical Type, Single Stage Cartridge JC7 Vertical, Vane Type
JC4 Level Type, Single Cartridge JC8 Level Type, Vane & Element Type
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Liquid-Liquid Coalescer
Design of PSC coalescers utilize the latest technology to bring clients the best liquid-liquid coalescer that separate a wide range of two immiscible liquids. Products that are emulsified and hazy are very difficult to separate. They require a specific coalescer design. PSC has the latest solution for even the most difficult to separate applications.
More stringent environmental compliance by governments around the world forces the industry to seek the help of liquid-liquid coalescing technology.
Radial flow coalescers are the latest technology available to PSC. They allow PSC to design high capacity applications while the vessel size remains small. Radial flow coalescers are also the preferred choice when retrofitting existing liquid-liquid separators for up to 100% more capacity and or improved efficiency.
PSC can design and manufacture coalescer internals, coalescer vessel and the complete skid mounted 2 or 3 phase coalesce systems. PSC can provide efficiencies of <15ppm of free water in oil or free oil in water. PSC can provide instead of a dual pre-filter coalescer vessel system to protect the coalescer pack from plugging, a CPI coalescer or Plate Pack Coalescer. The CPI coalescer will remove solids greater than 10microns and is installed in that same coalescer vessel, which is a more cost effective solution.
BENEFITS
1) Reduces cost due to smaller vessel design
2) Capacity increase for the existing vessels
3) Higher recovery of valuable products
4) Removal of haziness in the product
5) Reduces blending delays
6) Reduces wastewater production from tankage, separator and desalter
LLC Series
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Filter Separator
PSC two stage filter separator technology allows you to have the smallest possible vessel diameter, resulting in the lowest cost while removing aerosol liquids and solid particles efficiently.
The first stage contains replaceable coalescing filters mounted on a tube sheet. Here the bulk liquids and solids are removed while coalescing the aerosol liquid droplets into large ones (greater than 10 microns). Some of these coalesced droplets fall off the filter but the majority is pushed to the second stage due to the high surface velocity. In the second stage, these large droplets are removed by a high capacity Double Pocket Vane.
Filter separators can be designed both vertically and horizontally.
BENEFITS
1) Removes aerosol mist to protect downstream equipment from damage, fouling, pitting corrosion or deactivating of catalyst of molecular sieves.
2) Reduces amine or glycol foaming problem by removing solids and free liquid particles from the inlet gas stream
3) Allow low cost vessel designs
4) Debottleneck existing equipment, and adding up to 100% more capacity without requiring a new separator
5) Protects ultra low NOx burners from plugging, therefore preventing furnace heat imbalance
GLF Series
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Mesh Type Mist Eliminator
PSC provides high performance Mesh Type Mist Eliminators versus the standard units that many companies supply. In today’s demanding market standard, Mesh Mist Eliminators cannot meet the stringent requirements like higher capacity, better efficiency and lower pressure drop. For every new application, upgrade of debottlenecking such help is a must to make the most of your mist eliminator investment. Since the variables involved in specifying mesh mist eliminators are numerous the client should consult with PSC engineers before making a final selection.
The most widely used standard type of mesh mist eliminator is the 144 kg/m3 density made of metal and using a 0.028 wire. The knitted mesh is crimped and layer (alternate directions) to form a 100mm or 150mm thick unit. The rigidity is provided by a top and bottom grid structure welded together. Pads that are 914mm and lager are fabricated in narrow sections, enough to pass through a manway for assembly inside the separator. Recent advances in technology has brought mist eliminator designs and application expertise to new levels.
BENEFITS
1) Increases separator throughput or reduce size of new separators.
2) Improves product purity and reduce environmental pollution
3) Reduces operation cost
4) Increases recovery of valuable liquids and therefore reduce downstream corrosion
With the more advanced mesh mist eliminators it is critical for the design of the mist eliminator that you consider; vessel layout, proper gas distribution, location of inlet/outlet nozzle, liquid holding capacity and method of liquid drainage so the mesh pad will function efficiently and effectively.
MME Series
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Standard Vane
PSC manufactures all type of vane packs also known as Chevron vane mist eliminators. Vane consist of closely spaced corrugated plates that force the mist laden gas to follow the corrugated path. As the gas changes direction, the mist droplet momentum forces it to impact on the blades and coalesces to larger droplet and eventually drains off the blades. Vane packs are normally not efficient for mist droplets less than 20microns. However vanes are sturdier than mesh mist eliminators, provide a lower pressure drop and are less likely to plug. Vane blade spacing varies from 12 to 75mm depending on the dirt/solid loading. Vanes are available in all types of metal and plastic.
BENEFITS
1) Higher capacity than standard mesh mist eliminators
2) Lower pressure drop
3) Handles viscous or foaming liquids more efficiently
4) Dissipates slugs of liquid or high liquid mist loading
5) Resistant against violent upsets
6) Handles solids with minimal chance of plugging
STV Series
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Double Pocket Vane
To increase capacity on an existing separator or to reduce size of a new vessel, PSC’s Double Pocket Vane technology can be the answer. The unique geometry of this vane removes the collected liquids away from the gas. This design feature allows for twice the gas flow through the Double Pocket Vane versus a Standard Vane without any concern of liquid reentrainment. The blade geometry in addition allows more efficient mist removal than the standard vane. In applications where a mesh type mist eliminator would plug due to the presence of solids, waxes or paraffin. Double Pocket Vanes are the preferred solution. The Double Pocket Vane is plugging resistant and has the efficiency of a mesh mist eliminator. Double Pocket Vanes are also the preferred technology with applications that require a smaller vessel foot print or a vessel with limited weight allowance. Double Pocket Vanes can be supplied in any types of metals.
BENEFITS
1) Increases capacity up to 100%
2) Reduces size and weight for new vessel, resulting in reduced cost
3) Increases efficiency versus standard vanes
4) Debottleneck existing separators for capacity and efficiency
DPV Series
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Activated Carbon / Anthracite Filter System
JW-Type
It is Reverse Washing Type of Filtration System to use jointly a physical absorption and a heap filter to
insert a carbon or anthracite. In case of liquid phase, mainly it is used to a clean water treatment
INLE
TO
UTLE
T
In case of gas, it is utilized to remove an organic gas or a bad material and is mainly a fixed bed type
Application
1. Liquid Filtration- Removes smell, taste, chlorine and iron of drink water- Refines water to make a soft drink or brewing, water to use in a boiler and industrial water.- Filtration of amine and glycol
2. Gas Filtration- Purifies hydrogen, carbonic acid gas, chloride gas and other inorganic gas- Purifies ethylene, acetylene, and other gas about petrochemical- Purifies a fermented gas, a food gas, gas for chemical industry exhaust- Removes radiation elements of exhaust of a pile and desulfurizes a combustion exhaust- It is possible to remove a chemical action gas if using a special filler of alkali metals
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JW – C21 2 3
1 Design Type
2 Filling media materials(C : Activated carbon, A : Anthracite)
3 In/Out Pipe Diameter (Inch)
Model No. Flow Rate(㎡/HR)
In/Out Pipe Size
Mm(Inch)A B C D E F
Gravel quantity
to fill
Activatedcarbon to
fill
Weight(kg)
Carbon Steel
Standard
JW-C2 13-15 50A(2B) 1130 300 150 1830 450 2730 150 800 1450
JW-C3 30-35 80A(3B) 1720 500 150 1830 580 2960 350 1750 3200
JW-C4 48-55 100A(4B) 2130 500 200 2000 690 3380 550 2650 4700
JW-C5 80-90 125A(5B) 2690 500 250 2000 820 3520 850 4250 5500
JW-C6 120-130 150A(6B) 3300 500 300 2200 1000 3850 2800 7200 12500
JW-C8 180-200 200A(8B) 4000 500 350 2400 1180 4380 4400 9800 21000
Dimensions (mm)
It is basis to treat a clean water. According to the fluid class, the filler class and the size of filtration equipment are changed
Activated Carbon / Anthracite Filter System
C
A
Activated Carbon
Gravel
Gravel
T.L
DB
FE
A
T.L
B F
DC
E
Activated Carbon
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Auto Control Filter System
Porous Metal Blowback Filter System for Gaseous ServicePorous Metal Backwash Filter System for Liquid Service
High Solids RecoveryIt has a high performance to capture over 99.999% of the solids to be critical or hazardous or valuable
High Temperature OperationIt endures to a temperature to 1700 ℉ (927 ℃)
Automated OperationIt is fully automated system to be able to discharge solids periodically
Low Replacement CostsPSC Precision Metal Filter Element is a permanent self-supporting system which process a consistent performance
Long lasting Life SpanDowntime to wash is not necessary as it is washed by Blowback or Backwash based on the Venturi Pulse System
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Application of Blowback / Backwash System
Gaseous Service
Remove Solid particles in various gas steams to cover wide industries
Catalyst Retention or Radioactive Waste Removal Performance is very excellent in wide industries to cover Nuclear Industry or Chemical Industry
Loquid Service
Excellent Catalyst Retention from various Liquids
Excellent Performance to remove Solid Particles from a liquid flow
Excellent Filtration of a Polymer to have high viscosity
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
AUTO CLEANING STRAINER
PSC Corporation
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Auto Strainer
JA-B TypeBrush Wash Type
It is possible to operate continuous with a simple instrumentation
It is advantageous to a fluid of a high viscosity with mechanical washing method
Retention capacity of particle pollution, flow loss is low
Choice operation by a timer or by a switch for pressure drop is possible as Automatic Operation System
To repair and maintain is convenient, as it is an open and shut system to have installed a bottom cover
JA-R TypeBackwash Type
Continuous operation is possible
Filter granularity is delicate relatively comparing JA-B, as it is backwash system to utilize operation pressure
It is advantageous when an condition of pressure drop is high as an element has a small bore and pressure resistance is good
Choice operation by a timer or by a switch for pressure drop is possible as Automatic Operation System
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Auto Strainer – Application Area
JA-B Type
Chemical Industry area- Chemical industry, Synthetic resin, pigment,
paint, rubber, natural oil, oil refinery industry and etc.
Field of food and drink industry- Juice, Ketchup, Sausage, fish cake, sugar,
drink, wine, soda pop, vegetable edible oil, lactic ferments drink and etc.
Other Industry Area- Cutting oil, paper coloring and breaching,
bottle washing, removal of fat of wool and etc.
Clean Water Treatment Area- Water Supply Facilities, Sewage Treatment
Plant, Well and etc.
JA-R Type
Clean Water Treatment Area- Waterworks Treatment Plant, Sewage
Treatment Plant, Well, Boiler Water, Cooling Water, Waste Use in industry
Industry Area of Fuel and Lubricating Oil- Lubrication oil, Natural oil, Gasoline, Diesel,
Kerosene etc.
Drinking Water Area- Juice, Soda pop, Coke, Milk, Drinking Class
Chemistry Solvent Area
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JA – B - 10 – 20 - G1 2 3 4 5
1 Design Type
2 Brush Cleaning Type
3 Filter Basket Diameter (Inch)
4 Filter Cartridge Height (Inch)
5 Housing Material (G : Casting, S : Canning)
Model No.Flow Rate(㎡/HR)(Note 1)
In/Out Pipe Size
Mm(Inch)A B C D E F
Power of Reduction Machine
Washing brush Q’ty
JAB 10-20 60-80 100A(4B) 350 1150 850 1400 650 280 0.4(1/2) 3
JAB 12-24 100-130 125A(5B) 400 1270 970 1500 700 330 0.75(1) 4
JAB 14-28 140-180 150A(6B) 500 1520 1050 1800 800 430 0.75(1) 5
JAB 16-32 200-250 200A(8B) 600 1730 1180 2080 960 530 0.75(1) 5
JAB 18-36 280-350 250A(10B) 650 1850 1250 2250 1010 580 0.5(2) 6
JAB 22-48 420-550 300A(12B) 800 1330 1500 2830 1160 730 2.25(3) 8
Dimensions (mm)
Auto Strainer
* Note 1) Filtration rating is 420㎛ (40mesh) basis
1 Body Welded / Casting
2 Brush SS304/SS316
3 Reduction Machine
Standard Reduction Rate: 1/105
4 Auto ValveAir Press Type
Oil Pressure TypeMotor Operation Type
5 Control Panel
Waterproof TypeExplosion Proof Type(400W x 500H x 250L)
6 Pressure Drop Switch
Standard Measure Range (0~1Kg/㎠)
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JA – R - 06 – 2 - S1 2 3 4 5
1 Design Type
2 Rotating Arm Type
3 Filter Cartridge Quantity
4 Filter Cartridge Height (1:10”, 2:20”, 3:30”)
5 Housing Material (G : Casting, S : Canning)
Model No.Flow Rate(㎡/HR)(Note 1)
In/Out Pipe Size
Mm(Inch)A B C D E F
Power of Reduction Machine
Bach-WashedCartridge
Q’ty
JAR 03-1 15-20 50A(2B) 250 720 350 520 550 180 0.4(1/2) 1
JAR 04-1 25-35 80A(3B) 300 720 350 520 600 230 0.4(1/2) 1
JAR 06-2 60-80 100A(4B) 400 1120 450 870 700 330 0.75(1) 2
JAR 08-2 80-110 125A(5B) 450 1120 450 870 750 380 0.75(1) 2
JAR 12-2 110-160 150A(6B) 500 1250 600 950 800 430 0.75(1) 3
JAR 18-2 160-240 200A(8B) 900 1430 750 1130 960 530 1.5(2) 3
JAR 28-2 240-380 250A(10B) 750 1670 950 1320 1110 680 1.5(2) 5
JAR 42-2 330-520 300A(12B) 1000 2050 1200 1650 1360 930 2.25(3) 8
Dimensions (mm) Material : SS304
Auto Strainer
1 Body Welded / Casting(CS / SS304 // SS316)
2 Element Wedged Screen
3 Reduction Machine
Standard Reduction Rate: 1/105
4 Auto ValveAir Press Type
Oil Pressure TypeMotor Operation Type
5 Control Panel
Waterproof TypeExplosion Proof Type(400W x 500H x 250L)
6 Pressure Drop Switch
Standard Measure Range (0~1Kg/㎠)
* Note 1) Filtration rating is 250㎛ (60mesh) basis
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Strainer
PSC StrainerPSC Strainer is used widely to fluid and gas such as water, oil, air, gas in each field of Oil Refinery, Petrochemical Plant, Waterworks, Power Plant, Iron Manufacturing, Ship-building, Food, Paper Manufacturing, Synthetic Fiber
Material of PSC StrainerCarbon Steel - ASTM : A105, A216WCB, A53, A234, A106, A516- KS : Forging Steel, SCPH2, SPPS, SPHT, SB42
Stainless Steel - SS304, SS304L, SS316, SS316L, SS317
Alloy Steel and Special Steel- Monel, Hastelloy, Aluminum, Bronze, Copper Alloy, Chrome Alloy, Nickel Alloy and etc.
Strainer ElementElements is very important part as the heart of strainer. So, Corrosion Resistance, Filtration rate and Strength must be considered sufficiently and it must be a structure not to be bypassed the non-filtered fluid between element and body. PSC is manufacturing a high credible strainer that can’t compare with other production as it has a long experience and accumulated know-how in field of engineering
Connection StyleFlange Type || Socket Weld Type || Screw Type (PT,NPT) || Butt Weld Type
Applicable CodeKS || ANSI || DIN || JIS || BS || ISO || JPI || MSS || API
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Strainer Requirements
The Required Performance of Strainer is various and the summary is as followings :
1. Must filter exactly a thing over the necessary particles2. Filtration resistance of strainer must be minimum. Specially, it must be no-increase of urgent
Filtration Resistance after some using period passed- There is no problem as the absolute value of initial pressure drop in filtration resistance is small. But till a pressure drop reaches the maximum value, the filtration resistance is influenced by the wash cycle is long or shot
3. Must be a structure that repair and wash is easy4. Pipe Laying with the contiguous equipment (application equipment) must be easy
- If the location of nozzle is changed free, the Pipe Laying has a good structure5. Must be a structure to be maintained airtightness between a contacting part of element and a
parallel state of strainer6. Element and Equipment Body must maintain the strength to be able to endure in the high-
pressure-drop considering the internal, external pressure sufficiently
A Primary Factor to Obstruct a Filtration Performance
1. Case that screen is torn or tangled2. Poor sealing between a contacting part of element and element seat of body side3. Regarding No. 2 as fluid is an agitated situation during operation the load to happen from
element affects the sealing a lot, when the interval between element and seat in Bucket Type is big, when distance between the center of gravity and a seat is long in Y Type.So, the sealing is influenced by the flow wave of an element and the bypass of non-filtered fluid will happen owing to the poor sealing
PSC Strainer is designed by the basis of the above requisite and PSC has a long experienced know-how and a lot of customers are recognizing the quality of the excellent strainer in domestic and oversea petrochemical project for long years from Super Low Temperature -196℃ of the Ethylene Process till 350 ℃, a temperature of Heavy Grade Oil Resolution Facilities and the high pressure of 2500 pound basis
Oder Information
As this catalogue includes the basic item only, please contact us if it is an item of special material and big size. And it is possible to design filtration area free and to fabricate the big item as our strainer mainly is manufactured by welding
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Strainer Feature
Basket-Type
FeaturesKey Points for Design
1. Simple and compact Design in ANSI Standard
2. Low Pressure Drop
3. Wide Open Area
4. Excellent Welding Technique
5. Rich Experience
6. Substantial Construction
7. Solid, Smart Finish
8. Highly Resistant to Corrosion
9. Numerous Know-How acquired through a lot of efforts
Y-Type
Features(Other type than those specified on this catalogue)
1. Designated design codes such as ASME Code and etc. are applied to products
2. Most suitable materials are selected from PSC’s long experience for :
- High pressure and/or high temperature service- Low temperature service- Corrosive fluid service
3. Lining and Coating Materials are available such as :
- Rubber || Aluminizing || Stainless Steel Lining || Teflon Lining || Epoxy Coating || Galvanizing
4. Insulation, Steam Tracing and Steam Jacket are provided to meet operating requirements
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JB-120 Bucket Type Strainer
It is easy to install to the pipe that the height of inlet and outlet is different. It can maintain the low-pressure-drop and there is no-bypass of pollution material as the sealing store of an element is excellent.
Nom.SizeL H H1 H2
Element
A B Ø d1 L1
50 2 360 360 140 110 85 130
65 2 ½ 380 400 160 120 110 160
80 3 400 470 190 150 110 220
100 4 460 540 210 170 150 240
125 5 480 620 250 210 150 300
150 6 520 700 280 230 200 330
200 8 580 950 340 350 240 470
250 10 700 1060 380 440 320 530
300 12 760 1310 430 620 340 720
350 14 820 1520 470 770 400 880
400 16 900 1640 520 800 440 920
450 18 960 1840 600 900 480 1050
500 20 1000 1900 650 970 560 1120
600 24 1180 2390 750 1200 640 1370
No. Part Materials1 Shell A53-B (A516-60)2 Nozzle A53-B3 Nozzle Flange A1054 Shell Flange A1055 Cover Flange A1056 Head A516-607 Element Seat A516-608 Holder of Screen A240-3049 Screen SS304
10 Eye Bolt SS30411 Handle A3612 Drain A10513 Vent A10514 Stud Bolt A193-B715 Nuts A194-2H16 Gasket S.W.
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JB-130 Bucket Type Strainer
No. Part Materials1 Shell A53-B (A516-60)2 Nozzle A53-B3 Nozzle Flange A1054 Shell Flange A1055 Cover Flange A1056 Head A516-607 Element Seat A516-608 Holder of Screen A240-3049 Screen SS304
10 Eye Bolt SS30411 Handle A3612 Drain A10513 Vent A10514 Stud Bolt A193-B715 Nuts A194-2H16 Gasket S.W.
This type is used to the horizontal pipe that is the same height of inlet and outlet and it is advantageous to use and install to the big size as it maintains a horizontal state on the shape well. Bucket Type Strainer is a common style.
Nom.SizeL H H1
Element
A B Ø d1 L1
50 2 350 430 300 80 250
80 3 400 520 350 100 300
100 4 500 570 370 140 320
150 6 580 800 550 180 500
200 8 650 1040 760 220 700
250 10 800 1200 850 300 750
300 12 850 1420 1020 340 900
350 14 950 1650 1200 380 1050
400 16 1000 1900 1400 420 1250
450 18 1100 2100 1550 460 1400
500 20 1100 2200 1600 540 1450
600 24 1400 2450 1800 620 1600
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JB-150 Bucket Type Strainer
No. Part Materials
1 Body A210 WCB
2 Cover A210 WCB
3 Holder of Screen A240-304
4 Screen SS304
5 Eye Bolt SS304
6 Seat A240-304
7 Bolt A193-B7
8 Nut A194-2H
9 Vent A105
10 Drain A105
11 Gasket S.W.
Mainly it is applied to small size and the exterior is fine as the strainer body is casting. But it is widely used to a small size and low pressure less than #300 as the strength and filtration area is limited.
Nom.SizeL H H1
Element
A B Ø d1 L1
15 ½ 160 140 104 30 70
20 ¾ 160 150 111 30 70
25 1 180 178 132 40 80
40 1 ½ 230 211 155 50 90
50 2 260 222 161 60 90
80 3 355 344 248 90 150
100 4 425 397 286 110 170
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JY-200 Y Type Strainer
No. Part Materials
1 Body Pipe A53-B
2 Flange A105
3 Cover Flange A105
4 Element Seat A516-60
5 Holder of Screen A240-304
6 Screen SS304
7 Bolts A193-B7
8 Nuts A194-2H
9 Plug A105
10 Gasket S.W.
It is simple to install relatively as it is Y Type Strainer to adhere an element of common cylinder type sloping downward. Element is a cylinder type and there is never bypass of no-filtered fluid as seat is installed to the cover exactly. It is manufactured from various steels, stainless, alloy steel including a standard material and contacting flange can be manufactured according to an order style. The thickness is changed according to the grade of design pressure, temperature and design pressure and the spare part also is equipped to be suited to usage and use purpose.
Nom.SizeL L1
ElementA B Ø d1 L225 1 270 195 24 19140 1 ½ 280 235 34 23150 2 290 240 37 23665 2 ½ 320 250 52 24580 3 320 310 60 30590 3 ½ 360 330 70 325
100 4 400 350 80 345125 5 450 400 110 391150 6 480 440 120 430200 8 580 525 170 512250 10 680 630 220 617300 12 800 730 250 717350 14 930 850 300 834400 16 1000 890 340 877450 18 1080 960 400 938500 20 1140 1020 450 1009600 24 1320 1224 540 1214
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JY-210 Y Type Strainer
No. Part Materials
1 Body A216 WCB
2 Cover A216 WCB
3 Holder of Screen A240-304
4 Screen SS304
5 Bolt A193-B7
6 Nut A194-2H
7 Drain A105
8 Gasket S.W.
Mainly it is applied to small size and the exterior is fine as the body is casting. But it is widely utilized to low pressure less than #300 and small type as the strength and filtration area is limited.
Nom.Size LH Ø d
Element
A B #150 #300 Ø d1 L1
15 ½ 160 160 100 15 25 60
20 ¾ 160 160 110 20 30 68
25 1 180 180 125 25 34 73
40 1 ½ 240 240 160 40 55 100
50 2 260 260 170 50 58 120
65 2 ½ 270 270 180 65 83 120
80 3 290 360 220 80 92 163
100 4 335 410 310 100 130 230
150 6 520 520 580 150 200 293
200 8 580 580 - 200 250 400
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JY-220 Y Type Strainer
It is applied to small pipe less than 1 ½” (40A) and it is advantageous to the high pressure and the high temperature as the body is a forging, shape product. It is manufactured various as Flange Type. Socket Weld Type and Screw Type (NPT, PT) according to Pipe Connection Method.
JT-230 Y Type Strainer
No. Part Materials1 Body A1052 Cover A1053 Drain A1054 Gasket S.W.5 Holder of Screen A240-3046 Screen SS304
Nom.SizeL L1 D
ElementDrain
A B Ø d1 L215 ½ 75 59 36 19 31 3/8B20 ¾ 95 81 40 30 60 3/8B25 1 120 102 48 39 75 ½B 40 1 ½ 160 109 65 55 78 ¾B
No. Part Materials1 Body A1052 Cover A1053 Drain A1054 Gasket S.W.5 Holder of Screen A240-3046 Screen SS3047 Nozzle Flange A1058 Nozzle Neck A106-B
Nom.SizeL L1 D
ElementDrain
A B Ø d1 L215 ½ 200 59 36 19 31 3/8B20 ¾ 81 40 30 30 60 3/8B25 1 240 102 48 39 75 ½B 40 1 ½ 160 109 65 55 78 ¾B
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JT-310 T Type Strainer
No. Part Materials1 Body (TEE) A234-WPB2 Nozzle Neck A53-B3 Flange A1054 Shell Flange A1055 Cover Flange A1056 Element Seat A283-C7 Holder of Screen A240-3048 Screen SS3049 Bolt A193-B7
10 Nut A193-2H11 Gasket S.W.12 Handle A36
The washing operation of T-Type Strainer is simple as element is attached to the corner part of pipeline that is extension line of a usual fluid flow. It is possible that element obstructs the fluid flow of pipe as Shell is part of pipe in T-Type. Therefore the fluid resistance was minimized to be finished by reducing the element itself in order to utilize maximum the limited space and the cleaning cycle was extended as the uniform fluid distribution.
Nom.SizeL H Hf Hb
ElementA B Ø d1 Ø d2 L225 1 230 129 101 38 22 14 20040 1 ½ 290 163 127 57 30 20 26050 2 300 165 135 64 38 26 27065 2 ½ 320 166 154 76 52 34 28080 3 340 173 167 86 60 40 300
100 4 400 208 192 105 80 54 355125 5 470 246 224 124 110 74 420150 5 520 277 243 143 120 80 470200 8 600 310 290 178 170 114 550250 10 690 355 355 216 220 148 645300 12 820 434 386 254 250 166 770350 14 950 526 424 279 300 200 890400 16 1120 668 452 305 340 226 1060450 18 1270 767 503 343 380 254 1200500 20 1380 836 544 381 430 288 1300600 24 1580 978 602 432 530 354 1500
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JT-320 T Type Strainer
It is used to high temperature and high pressure of a petrochemical process and is composed by an element of Bathtub type. It is advantageous to a petrochemical process of high temperature and high pressure as the durability is excellent and a pollution material is heaped well and element is a bathtub.
JT-330 T Type Strainer
No. Part Materials1 Body(Tee) A234-WPB2 Flange A1053 Cover Flange A1054 Nozzle Neck A53-B5 Holder Screen A240-3046 Screen SS3047 Vent A105
Nom.SizeL L1 D
A B50 2 127 127 2560 2 ½ 152.4 148 3080 3 171.4 159 35
100 4 209.6 182 50150 6 285.8 280 75200 8 355.6 380 95250 10 431.8 470 120300 12 508 660 145350 14 558.8 670 165400 16 609.6 760 185450 18 685.8 860 210500 20 762 960 235600 24 863.6 1140 280
No. Part Materials1 Body(Tee) A234-WPB2 Flange A1053 Cover Flange A1054 Gasket S.W.5 Bolt A193-B76 Nut A194-2H
Nom.Size LL1 H1
A B #150 #30050 2 192 198 63.5 63.565 2 ½ 225 230 76.2 76.280 3 244 253 85.7 85.7
100 4 289 299 104.8 104.8150 6 377 384 142.9 142.9200 8 460 470 177.8 177.8250 10 535 549 215.9 215.9300 12 625 640 254 254350 14 689 703 279.4 279.4400 16 740 757 304.8 304.8450 18 827 846 342.9 342.9500 20 910 925 381 381600 24 1018 1035 431.8 431.8
It has a very low-pressure-loss and a soft liquid flow and is possible to install to the horizontal pipe in the T-Type.
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JC-410, JC-420 Temporary Strainer
No. Part Materials1 Body A240-3042 Holder of Screen A240-3043 Screen SS3044 Special Ring A240-304
Mainly, Temporary Strainer is used in flushing before starting operation and it is a simple Strainer to install between flanges of single pipe. It is used to a permanent strainer for an instrument use also.
NomSize T W H A
DD1
JC-420 JC-410JIS10K
JIS20K
ANSI#150
ANSI#300 D2 L Short Long
½ B 2 20 85 10 55 55 47 53 13 22 35¾ B 2 20 85 10 60 60 56 66 18 9 35 26 451 B 2 20 90 10 72 72 66 72 24 12 45 55 55
1 ½ B 2 20 100 10 87 87 85 94 36 18 60 42 782B 2 20 120 10 102 102 104 110 48 24 75 52 100
2 ½B 2 20 140 10 122 122 123 130 60 30 95 62 1223B 2 20 150 10 132 132 135 149 72 36 110 74 1454B 2 20 160 10 157 163 173 180 95 48 150 95 1905B 3 25 180 12 188 200 196 215 118 59 170 115 2356B 3 25 200 12 218 235 221 250 142 71 210 140 2808B 3 25 230 12 268 280 277 307 188 94 270 175 360
10B 3 25 260 12 330 353 338 361 235 118 350 220 45512B 3 25 300 12 375 403 405 421 280 140 400 260 54014B 6 35 330 12 420 447 449 485 325 163 460 300 62016B 6 35 360 12 483 507 512 539 375 188 550 340 71518B 6 40 390 12 538 572 547 596 425 213 600 385 81020B 6 40 420 12 593 627 604 653 470 235 700 425 89524B 6 40 480 12 698 731 715 774 570 285 800 510 1070
PSC Corporation
`
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
JD-500 Duplex Type Strainer
It is a strainer that is designed in order to operate continuous while cleaning the internal element as Duplex Strainer that two strainers connected in a row can convert a flow direction by a valve operation.Incase of a Common Duplex Strainer. It can be operated without any intermittence of fluid flow because valve of inlet side and outlet side must be connected.But JD-500 Type install the 3-way Check Valve in outlet side and a control valve in inlet side. And it is a system that 3-way Check Valve in outlet side converts the fluid direction automatically by the difference of an internal pressure as soon as operating the converting control valve.
Duplex Strainer- Bucket type
Duplex Strainer- Bucket Casting type
PSC Corporation
649, Cheoyong-ri, Onsan-eup, Ulju-gun, Ulsan, Korea
Standard Screen Micrometer Conversion Chart
US andASTM STD.Sieve Number
Actual Opening
Inches Micrometers
10 0.0787 2000
12 0.0661 1680
14 0.0555 1410
16 0.0469 1190
18 0.0394 1000
20 0.0331 840
25 0.0280 710
30 0.0232 590
35 0.0197 500
40 0.0165 420
45 0.0138 350
50 0.0117 297
60 0.0098 250
70 0.0083 210
80 0.0070 177
100 0.0059 149
120 0.0049 125
140 0.0041 105
170 0.0035 88
200 0.0029 74
230 0.0024 62
270 0.0021 53
325 0.0017 44
400 0.00142 36
550 0.00099 25
625 0.00079 20
1,250 0.000394 10
1,750 0.000315 8
2,500 0.000197 5
5,000 0.000099 2.5
12,000 0.0000394 1
Micrometer Comparisons
Substance Micrometers
Table Salt 100
Human Hair (AVG.) 50-70
White blood cell 25
Talcum powder 10 10
Cocoa 8-10
Red Blood Cell 8
Bacteria (cocci) 2
Note. Lower limit of visibility (naked eye) –40 micrometers
Relative Size of ParticlesMagnification 500 times
44 Micrometers325 mesh
74 Micrometers
149 Micrometers100 mesh
2 Micrometers
5 Micrometers
8 Micrometers
25 Micrometers
Linear Equivalents
1 inch = 25.4 millimeters = 25,400 micrometers
1 millimeter = 0.0394 inches = 1.000 micrometers
1 micrometer = 125.400
of an inch = 0.001 millimeters
1 micrometer = 3.94 x 10 -5 inches = 0.000039 inches
Conversion Rates Metric Conversion Formulas
1 cu. ft = 7.48 gal. mm = inches x 25.4
1 ga. = 231 cu.in. m = feet x 0.3048
1cu.ft. water = 62.42 lb. cm3 = cu. in x 16.39
1 gal. water = 8.34 lb. m3 = cu. ft. x 0.028
1 lb. water = 27.7 cu.in. kg = pounds x 0.454
1 U.S. gal. = 0.833 lmp. gal. kPa = psi x 6.895
1 lb./in2 = 2.31 ft. of water=2.2036 in. HG. lpm = gpm x 3.785
℉ = 9/5℃ + 32 ℃ = 5/9 (℉ - 32)
Formulas
velocity (ft. per sec.) = 0.4085 x gpmd2 (id in.)
brake h.p =gpm x total head in ft. x (specificgravity)
3960 x (pump efficiency)
PSC Corporation