Embed Size (px)
Citation preview
Cover Letter
TO WHOM IT MAY CONCERN
I am Process Engineer with almost 6 Years’ experience Fertilizer Industry Experience. Well versed with
Process Engineering, Modeling & Designing, Sizing & Rating of Process Equipment’s & Instruments. I
have been working in the technical services department as Process Engineer Ammonia and responsible
for plant trouble shooting, process engineering, Plant De‐bottlenecking studies. I have also been
involved in the revamp project of Ammonia plant where I was involved in process design, equipment
selection & design, PID, PFDs, control philosophy.
Areas of Specialties:
Plant Performance monitoring and Reliability Improvement Programs
Identification & implementation of cost curbing projects through MOC Procedure
Plant capacity enhancement studies
Experience in Process Simulations software’s such as Aspen Plus and Hysys for plant
performance and optimization.
Experience of Plant relocation studies, Basic and Detail Engineering work scope and documents
review
Keeping in view of my academics, achievements, all round experience in technical services and projects,
I am confident that I add value to your esteemed organization through my services and activities. I am
also sure that I live up to your expectations and justify my position once I am entrusted.
Looking forward to hear from you
Best Regards,
Abdul Jabbar Process Engineer, Fatima Fertilizer Company Cell No. : 00923314929011
Professional Resume 1
ABDUL JABBAR (Process Engineer) Phone No: +92-331-4929011 Skype ID: abduljabbar131 Nationality: Pakistani Passport No: AK8025941 Date of Birth: 13-November-1987 Email: [email protected] Address: HOUSE NO-042 BOQ, FATIMA FERTILIZER COMPANY LIMITED, SADIKABAD DISTRICT RAHIM YAR KHAN PAKISTAN
CAREER OBJECTIVE To join venerated organization where accomplishments are rewarded withresponsibilities, which maximize my natural strength as a problem solver and where my experience,formal education, technical skills and dedication will have a direct influence on company escalation.
EXPERIENCE PROFILE
JOB EXPERIENCE Total 6 Years’ experience of Process Engineering in Technical Department atFatima Fertilizer Company Limited. Working as Process Engineer at Ammonia Plant and directlyinvolved in Plant monitoring, Plant Performance Reports, evaluating technical, engineering & capacity enhancement studies and proposals.
PLANT CAPACITY ENHANCEMENT PROJECT
As Process Engineer contributed in revamp study of Ammonia Plant up to 120% of the base designcapacity. Engaged in following responsibilities during Revamp Project
‐ Scope finalization and Kick‐Off meetings with Haldor Topsoe A/S (HTAS) team to achieve most viable options (energy wise) for achieving target ammonia plant capacity.
‐ Collection of extensive plant data and correspondence with HTAS for developing Ammonia Plant base case model.
‐ Review of base case and Revamp PFD’s in perspective of plant operational, mechanicallimitations and problems.
‐ Finalization of revamp study aligned with targets and objectives.
‐ Finalization Basic Engineering Design (BED) work scope with Haldor Topsoe A/S Denmark for Ammonia Plant Revamp for 120% of base case capacity.
‐ Review process engineering related work scope of BED Package deliverables. Part‐time involved in review of Detail Engineering documents of Ammonia Revamp. Phase‐I execution of revamp project shall be carried in Oct‐2015.
Professional Resume 2
PLANT PERFORMANCE AND RELIABILITY MONITORING
‐ Daily monitoring of plant operating parameters and highlighting areas of plant optimization and improvement for operation team.
‐ Plant Production Loss Accounting on daily basis. Presenting Data to management on Monthly and yearly basis for addressing reliability and rate restrictions contributing factors.
‐ Issuance of Production Loss Reporting against budgeted figures and identification/ providetechnical support for Root cause analysis (RCA) of Incidents and plant tripping. Generatingeffective and consolidated recommendations to improve plant reliability.
‐ Lead and supervise Process Engineering related activities in Turn Around e.g. exchanger chemical cleaning, catalyst replacements, and tracking project modifications.
‐ Identification & implementation of cost curbing projects to improve the safety, reliability, mechanical integrity, plant efficiency, operability and Plant capacity enhancement projects as per Management of change Procedure (MOC) Procedure.
‐ Active member in implementation of Process Safety Management (PSM) culture at site. Participate in PHA studies to improve plant process safety. Provide technical support for Root cause analysis (RCA) of Process Safety Incidents.
MAJOR PROJECTS IMPLEMENTED
‐ Study for installation of Natural Gas Booster Compressor facility at Natural Gas main supply lineof plant battery limit.
‐ Minimizing Plant Front End Delta P by a) Installation of by‐pass valve across main feed gas valve which was posing high delta P b) Skimming of methanator catalyst to address high delta P issuec) Chemical cleaning of heat exchanger and furnace coils.
‐ Improvement of ammonia plant refrigeration system by installation of the two old ammonia refrigeration condensers in parallel to existing condensers.
‐ Detailed evaluation and implementation of the series to parallel cooling water supply to all CO2condensers at Ammonia Catacarb CO2 removal system resulted in margin in urea CO2compressor.
Professional Resume 3
JOB SPECIFIC CHALLENGES AND EXPERIENCE
‐ Ammonia Plant CATACARB (CO2 absorption system) suffered from worst Foaming experience in Sep‐2012 due to activated carbon slip into system. Ammonia Plant suffered from extensive production loss during incident. As a process engineer directly involved in identifying,addressing and encountering operational issues caused by foaming of catacarb solution. Most challenging, hectic professional experience gave me opportunities to enhance my professionalcore values (e.g Problem solving, Courageous and decisive, Facing the facts and involving each & every individual to play his role for crisis management).
‐ Ammonia plant was CF‐Barun designed in 1960. Working with KBR 1st purifier technology and suffered from various operational issues. However utilization past experience of relocated plantenabled plant reliable operation through lesson learning’s.
PROFESSIONAL SKILLS
As a process engineer involved in following evaluations, calculations and reporting ‐ Performance evaluation of compressor and steam & Gas turbines ‐ Performance evaluation of Ammonia plant catalyst specific (reforming, shift conversion and
methanation etc.) ‐ Performance evaluation of Heat Exchangers. ‐ Perform pressure drop calculations, sizing & rating of control valves, restriction orifice etc. ‐ Heat and material Balance of process Plants. Development of PFDs, P&IDs and UFDs. ‐ Hydraulic calculations, line sizing, selection size of equipment and instrument. ‐ PSV sizing & selection, header sizing and knock out drum sizing. ‐ Effective utilization of simulation software Aspen HYSYS, Aspen Plus, EDR for plant performance
monitoring and modification.
PROFESSIONAL TRAINING
Engineering Software Training and certificates 1. Training course on “Dynamic modeling using Aspen HYSYS Dynamic by Aspen Tech Partner
Phi‐tech Solution on 28th Dec‐2010. 2. Training session on “ASPEN PLUS & ASPEN EDR” at plant site FFCL by Aspen Tech Partner Phi‐
tech Solution on July‐2013. 3. Training session on ASPEN PLUS Dynamics at plant site FFCL by Aspen Tech Partner Phi‐tech
Solution on July‐2013. Safety and Environment related certification
4. Process Safety Management (PSM) Workshop on 22 Elements in House at Fatima site. 5. Process Hazard Techniques (PHA) by DuPont
Professional Resume 4
Soft Skill Certificates
6. Technical weport writing skill development program by Institute of Training and consultancy 7. SWOT Analysis 8. Basic managerial skill and effective presentation skills 9. Advance Microsoft excel
EDUCATIONAL PROFILE
Degree/Certificate Institute Grade
Bachelor's degree of Chemical Engineering
University of Engineering and Technology Lahore, Punjab, Pakistan
A
Intermediate Board of Intermediate & Secondary Education Lahore
A
Matriculation Board of Intermediate & Secondary Education Lahore
A+
PERSONAL DATA
Father’s name ABDUL SITTAR
National ID card Number 35202‐8840594‐9
Email ID [email protected]
Alternative Email ID [email protected]
Marital status Single
Religion Islam
Nationality Pakistani
Date of Birth 13th November‐1987
Passport number AK8025941
REFERENCES
Can be furnished upon demand
