8/10/2019 PRO1_03E [ ] [ ]

1/7

Setup of a Training Area with S7-300 ..................................................................... 2Configuration of the Training Unit S7-300 ............................................................................................ 3

Setup of a Training Area with S7-400 ................................................................................ 4

Configuration of the Training Unit S7-400 ......................................................................................... 5

The Simulator ........................................................................................................................... 6

The Conve or Model .................................................................................................................... 7

Training Centerfor Automation and Drives

ST-7PRO1Training UnitsPage 1

8/10/2019 PRO1_03E [ ] [ ]

2/7

Contents of the The training kit consists of the following components:ra n ng n - programma e og c con ro er w or -

Digital input and output modules, analog modules

Simulator with digital and analog sections Conveyor model

Note:It is quite possible that your training area is not equipped with the conveyormodel shown in the slide above, but rather with the conveyor modelpictured below.

Training Centerfor Automation and Drives

ST-7PRO1Training UnitsPage 2

8/10/2019 PRO1_03E [ ] [ ]

3/7

Configuration The programmable controller is configured with the following modules:o ers on o : ower upp y

Slot 2: CPU 314 or CPU 315-2 DP

Slot 4: Digital input 16x24V Inputs from the simulator Slot 5: Digital input 16x24V Pushwheel buttonsSlot 6: Digital output 16x24V 0.5A Outputs from the simulator Slot 7: Digital output 16x24V 0.5A Digital displaySlot 8: Digital input 16x24V Conveyor model inputsSlot 9: Digital output 16x24V 0.5A Conveyor model outputsSlot 10: Analog module 4 AI/4 AO Adjustable from the simulator

Configuration The programmable controller is configured with the following modules:of Version B Slot 1: Power Supply 24V/5A

Slot 2: CPU 314 or CPU 315-2 DPSlot 4: Digital input 32x24V Inputs from the simulator

and pushwheel buttonsSlot 5: Digital output 32x24V/0.5A Outputs from the simulator

and digital displaySlot 6: Digital input and output Conveyor model

.Slot 7: Analog input 2 AI Analog section from simulator

Addresses Fixed slot addressing is used for the S7-300 (CPU 312-314). The moduleaddresses are shown in the slide.

The starting addresses of the modules can be set by parameter assignment on theCPU 315-2DP and for S7-400.

Training Centerfor Automation and Drives

ST-7PRO1Training UnitsPage 3

8/10/2019 PRO1_03E [ ] [ ]

4/7

Contents of the The training kit consists of the following components:ra n ng n - programma e og c con ro er w or -

Digital input and output modules, analog modules

Simulator with digital and analog sections Conveyor model

Note:It is quite possible that your training area is not equipped with the conveyormodel shown in the slide above, but rather with the conveyor modelpictured below.

Training Centerfor Automation and Drives

ST-7PRO1Training UnitsPage 4

8/10/2019 PRO1_03E [ ] [ ]

5/7

8/10/2019 PRO1_03E [ ] [ ]

6/7

Design The Simulator is connected to the S7-300 or S7-400 training unit by two cables. It isn ree sec ons:

Binary section with 16 switches/momentary-contact switches and 16 LED's

Digital section with 4 pushwheel buttons and a digital display. These operatewith BCD values,

Analog section with a voltmeter for displaying the values at analog channels 0and 1 or the analog outputs 0 and 1. You use the selector switch to choose thevo age va ue you wan o mon or. ere are wo separa e

potentiometers for setting the values for the analog inputs.

Addressing You use the following addresses to address the inputs and outputs in your userprogram:

Sensor / ActuatorVersion A(DI16, DQ16)

Version B(DI32, DQ32)

S7-400(Default addresses)

Switch / M.C. Sw.

LEDs

Pushwheel buttons

IW 0

QW 8

IW 4

IW 0

QW 4

IW 2

IW 28

QW 36

IW 30

Training Centerfor Automation and Drives

ST-7PRO1Training UnitsPage 6

Analog channels

PIW 352/354

PIW 304/306

PIW 1216/1230

8/10/2019 PRO1_03E [ ] [ ]

7/7

Design The slide shows a diagram of the conveyor model with its sensors and actuators.

Addresses S7-300 S7-300 S7-400Ver. A Ver. B (w/o Sensor / Actuator Symbol(DI16, (DI32, HWDO16) DO32) Config)

I 16.0 I 8.0 I 32.0 Light barrier LB 1 LB1I 16.1 I 8.1 I 32.1 Ackn. switch, Loc 1 S1I 16.2 I 8.2 I 32.2 Ackn. switch, Loc 2 S2 . . . . ,I 16.4 I 8.4 I 32.4 Ackn. switch, Final Assy S4I 16.5 I 8.5 I 32.5 Proximity switch 1 INI1I 16.6 I 8.6 I 32.6 Proximity switch 2 INI2I 16.7 I 8.7 I 32.7 Proximity switch 3 INI3

Q 20.1 Q 8.1 Q 40.1 LED at Location 1 H1

Q 20.2 Q 8.2 Q 40.2 LED at Location 2 H2Q 20.3 Q 8.3 Q 40.3 LED at Location 3 H3Q 20.4 Q 8.4 Q 40.4 LED at Final Assembl H4Q 20.5 Q 8.5 Q 40.5 Conveyor oper. to right K1_CONVRQ 20.6 Q 8.6 Q 40.6 Conveyor oper. to left K2_CONVLQ 20.7 Q 8.7 Q 40.7 Horn HORN

Training Centerfor Automation and Drives

ST-7PRO1Training UnitsPage 7