Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Page 1 of 27939500486 Rev K
Privacy Wall & Glass Selections Pivot-Hinged Doorand Privacy Wall Butt-Hinged Door
(For products manufactured prior to September 14, 2009)
#2 ACR BIT
3/16" HEX BIT
5/32DRILL BIT
RAYBO
1"OPEN ENDWRENCH
3/8" HEX SOCKET
5/64 HEX
If you have a problem, question, or request, callyour local dealer, or Steelcase Line 1 at888.STEELCASE (888.783.3522)for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500)Or visit our website: www.steelcase.com© 2005 Steelcase Inc. Grand Rapids, MI 49501 U.S.A.
Printed in U.S.A.
PLUMB BOB
Full-Height Full-Height PairTransom Transom Pair
Topic Page
Privacy Wall Pivot-Hinged Door Components
Glass Selections Pivot-Hinged Door Components
Pivot-Hinged Door Frame Assembly
High Voltage Switch Installation
Low Voltage Switch Installation
Butt-Hinged Door Components
Butt-Hinged Door Frame Assembly
2
3
5
14
19
20
21
NOTE:
For etched/pattern glass orientation please refer to the installation drawings. Unless noted otherwise, use the default.
DEFAULT GLASS ORIENTATION: ETCHED GLASS: Rough side to go on the inside of the office space. PATTERN GLASS: Rough side to go on the outside of the office space.
ETCHED GLASS STYLES: • Satin • Mist
PATTERN GLASS STYLES: • Waterfall • Bamboo • Harp • Mirage
Page 2 of 27939500486 Rev K
PIVOT HARDWARE BAG
TOP PLATEASSEMBLY
LOWER PIVOTASSEMBLY
TOP PIVOTASSEMBLY
BOTTOM PLATEASSEMBLY
DOOR(Ordered separatelyfrom frame unit.)
TRANSOMFRAME
40" IFFIELD ADDED
IF FIELD ADDEDPER HARDWAREREQUIREMENTS
SUPPORT PLATE OUTERPLINTH
DOOR HANDLE MORTISE HANDLE (LATCH VERSION)
(Ordered separately from frame unit.)
or
STRIKE PLATEASSEMBLY
KEEPERSIDE
HINGESIDE
FULL HEIGHT FRAME (KNOCK-DOWN)WITH/WITHOUT POWER
TOP RAIL ASSEMBLY, TOP STRIKE ASSEMBLY, CLAMP CHANNELS, POST EXTENSION MOUNTING ASSEMBLIES UPRIGHT (KEEPER SIDE) & UPRIGHT (HINGE SIDE).
DOOR SEAL &DOOR SEAL RETAINER
Privacy Wall Pivot-Hinged Door Components
STURRUPASSEMBLY
DOOR HANDLE MORTISE HANDLE (LOCK VERSION)
LOAD TRANSFERBRACKET
Page 3 of 27939500486 Rev K
Glass SelectionsPivot-Hinged Door Components
LOW VOLTAGEWIRE
WATTSTOPPER
POWER (OPTIONAL)LOW VOLTAGE COMPONENTS
POWER (OPTIONAL)HIGH VOLTAGE COMPONENTS
HINGE SIDE PLINTH forHIGH or LOW VOLTAGESWITCH
BOXSTRAP
SWITCH
HIGH VOLTAGEELECTRICAL BOX
SWITCHPLATE
TRANSOM FRAMEwith HIGH VOLTAGE POWER
TRANSOM FRAMEwith LOW VOLTAGEPOWER
TRANSOM FRAMEwith NO POWER
FULL HEIGHT FRAMEwith HIGH VOLTAGE POWER
FULL HEIGHT FRAMEwith LOW VOLTAGEPOWER
FULL HEIGHT FRAMEwith NO POWER
KEEPER SIDE PLINTHfor HIGH or LOW
VOLTAGE SWITCH
HINGE SIDE PLINTH
KEEPER SIDE PLINTH
NO SWITCH
LOW VOLTAGESWITCH
QUICKCONNECTS
OR
Page 4 of 27939500486 Rev K
Glass SelectionsPivot-Hinged Door Components (cont.)
DOOR(Ordered separatelyfrom frame unit.)
40" IFFIELD ADDED
IF FIELD ADDEDPER HARDWAREREQUIREMENTS PIVOT HARDWARE BAG
LOWER PIVOTASSEMBLY
TOP PIVOTASSEMBLY
STRIKE PLATEASSEMBLY
DOOR SEAL &DOOR SEAL RETAINER
NOTE:For a full height GlassSelections Door.Maximum ceilingheight is108".
SPACERS
DOOR HANDLE MORTISE HANDLE (LATCH VERSION)
(Ordered separately from frame unit.)
or
DOOR HANDLE MORTISE HANDLE (LOCK VERSION)
LOAD TRANSFERBRACKET
TOP PLATEASSEMBLY
BOTTOM PLATEASSEMBLY
Page 5 of 27939500486 Rev K
POST EXTENSIONMOUNTING ASSEMBLY
TOP RAILASSEMBLY
CLAMPCHANNEL
1a
1b
1c
OUTER DOORVERTICAL
TOP STRIKEASSEMBLY
2FULL HEIGHTPIVOT-HINGED DOORFRAME ASSEMBLY(Privacy Wall Only)
Full Height GlassSelections ispre-assembled.
If you have a transom frame,start assembly on next page.
1. Install the post extensionmounting assembly on the outerdoor vertical by hooking into theholes (1a) on both sides. Slidethe clamp channel into the outerdoor vertical and line up holes(1b) on both sides. Install thetop rail assembly using two (2)#10-16 x 1" pan head selftapping screws provided (1c).
2. Install the top strikeassembly. Temporarily secure itinto place with tape. The topstrike will be secured later whenthe door clearance has beenestablished.
Page 6 of 27939500486 Rev K
HEADER
2a
1a
UPPER PIVOT ASSEMBLY
#10-24 X 5/8"FLAT HEAD TYPE 1
THREAD CUTTING SCREWS
1b
OUTERDOORVERTICAL
SUPPORTPLATE
LOWER PIVOTASSEMBLY
OUTERDOORVERTICAL
These steps are applicable for Privacy Wall and Glass Selections
OUTERDOORVERTICAL
SPACER
Glass Selections application
Privacy Wall applicationLOWER PIVOT
ASSEMBLY
TOP STRIKE ASSEMBLYSHIPPING POSITION
INSTALL THE TOPSTRIKE ASSEMBLY
IN THE UPPERMOST POSITION
2b
2c
1. Relocated the top strikeassembly. Temporarily secure itinto place with tape. The topstrike will be secured later whenthe door clearance has beenestablished.
Install upper pivot assembly intothe opening of the header (1a)using two (2) #10-24 x 5/8" flathead type screws provided inthe pivot hardware kit (1b).
2. Place the support plateinto the bottom of the outerdoor as shown (2a and 2b).Next locate the lower pivotassembly next to thesupport plate and secureusing two (2) 1/4-20 x 1/2"round head screws andlock washers provided inpivot hardware kit (2c).
NOTE: This assembly islocated in the groove detailof the outer door vertical onthe pivot side. This will beadjusted later in thisassembly direction.
Page 7 of 27939500486 Rev K
3b
This step is applicablefor Privacy Wall and Glass Selections
LOAD TRANSFERCLIP
3/8" LONGSELF-DRILLING SCREW
SUPPORTPLATE
3a
3. Place the support plate or sturrupassembly into the bottom of the outerdoor vertical on the strike side of theframe (3a). Secure with two (2) 1/4-20x 1/2" round head screws and lockwashers (3b).
4. Mount the load transfer clip to thestrike side of the door frame, justabove the strike plate zone, with a3/8" long self-drilling screw.
NOTE: The load transferclip is only used on standard pivotdoor frames. It is not required on pivotdoor frames with a switch cutout.
Page 8 of 27939500486 Rev K
6
5
7
FLOOR
OUTERDOORVERTICAL
2-1/4"1"
1/4"
(MAX.)(NOM.)(MIN.)
These steps are applicable for Privacy Wall and Glass Selections
6
MAKE SURE EDGESARE ALIGNED5. Lift frame up and align with panels.
6. Determine which outer door vertical must bemoved upward to make the inner headerassembly level horizontally. Tighten screwssecuring the door vertical that doesn't needadjustment, making sure the pivot sidedoor vertical is at least 1/4" offthe floor.
7. Check forsquareness bymeasuring dooropening.
Page 9 of 27939500486 Rev K
8. Slide door seal into the door seal retainer (8a). On hinge side, apply door seal assembly at top and work downward (8b). On strike plate side, apply door seal strip in two (2) places (8c).
8b8a
8c
8c
This step is applicable for Privacy Wall only.
REMOVE AREA ONDOOR SEAL RETAINER
FOR CLEARANCEOF TOP STRIKE
ASSEMBLY BRACKET
Page 10 of 27939500486 Rev K
99
OUTERPLINTH
OUTERPLINTH
DOOR SEAL RETAINERREMOVED AND DOORSEAL INSTALLED INTOPLINTH
DOOR SEAL RETAINERREMOVED AND DOOR
SEAL INSTALLED INTOPLINTH
9. Attach outer plinth on each side at the baseof the frame with a #10-16 x 1" flat head screwprovided and attach felt over plinth as shown.
Page 11 of 27939500486 Rev K
10a
10a
10b
10c
10cTOP PLATE ASSEMBLY
(BUSHING IS BRONZE IN COLOR)
10b
BOTTOM PLATE ASSEMBLY(BUSHING IS SILVER IN COLOR)
BOTTOM
TOP
DEEP POCKET
SHALLOW POCKET
#14 x 1-1/4" FLATHEAD SCREWS
#14 x 1-1/4" FLATHEAD SCREWS
This step is applicablefor Privacy Wall and Glass Selections
10. Drill 5/32" dia.pilot holes (10b). Installupper and lowerbushings (from pivothardware kit shippedwith door frame) intothe routed pockets onthe top and bottom ofthe door and securewith #14 x 1-1/4" flathead screws provided(10c).
NOTE: The top andbottom bushings aredifferent. Make sure toinstall the bushings inthe correct orientationand location. Thebushing with the bronzebearing installs in theshallow pocket routedat the top of the door.
NOTE: The door ispackaged/shippedseperately from thedoor frame package.
Page 12 of 27939500486 Rev K
DIM. X
11b
11c
DIM. X + 1/8"
11. Temporarily position pivotpin in door (11a).
Measure and note Dim. X (11b).
Position the top strike assemblyrelative to the pivot pin as shown(11c).
Fasten the strike assemblyusing two (2) #10 x 1/2" panhead self-drilling teks screws,provided.
Fasten pivot side first, level thestrike assembly then fastenother side.
11a
Page 13 of 27939500486 Rev K
13b13a
STRIKE PLATE
LOWER PIVOT ASSEMBLY
12bUPPER PIVOT
ASSEMBLY
12a
PIVOT PIN
SCREW WHICHSECURES THEPIVOT PIN
DOOR
This step is applicablefor Privacy Wall and Glass Selections
UPPER PIVOTASSEMBLY
12c 12d
3/16" MAXGAP
INNER HEADERASSEMBLY
DOOR
12e
PIVOT PIN
12. Loosen the screw securing thepivot pin on the upper pivot assembly(if necessary) (12a). Install the dooronto lower pivot assembly (12b) andpush upper pin assembly into theinner header (12c).Tilt the door into position under theheader and pin (12d). The upperpivot pin must drop into and engagethe upper pivot bushing.
CAUTION: To prevent personal injury,retighten the locking screw securely tomaintain positive engagement of theupper pivot pin into the bushingassembly on the door.
Tighten locking screw securely(recommend hand screwdriver toprevent damage) to ensure properengagement of upper pivot pin intotop of door.
13. Install strike plate to the innerdoor vertical (strike side) (13a) withthe two (2) #10-16 x 1/2" flat headscrews provided (13b).
High Voltage Switch Installation
1. Remove the desired knockout on the high voltage electrical box.
NOTE: Only the bottom knock-out can be removed for the Glass Selections Transom scenerio because the power cannot be routed through the ceiling. All other scenerios can be routed through the ceiling.
2. Route the conduit through the frame, out of opening in the frame and attach to the high voltage electrical box depending on the desired scenerio.
1
HIGH VOLTAGEELECTRICAL BOX
KNOCK-OUT
2
CONDUIT
HIGH VOLTAGEELECTRICAL BOX
OPENING INTHE FRAME
Page 14 of 27939500486 Rev K
Page 15 of 27939500486 Rev K
3. With conduit properly attached, feed conduit back through opening in frame including the high voltage electrical box (3a). Attach box to vertical rail (3b). Attachment method depends on if your installing Privacy Wall or Glass Selections.
3a
SCREW
3b
SCREW
Privacy WallVersion
Glass SelectionsVersion
Page 16 of 27939500486 Rev K
4. Position strap on switch.
4a. Using flade blade screwdriver, twist to bend tab, assembling strap to switch.
4
4a
STRAP
SWITCH
BEFORE
AFTER
Page 17 of 27939500486 Rev K
4b. Wire switch.
NOTE: Must be a licensed electrician to wire switch.Attach wired assembly to electrical box using two (2) screws (4c).Attach switch plate to electrical box using two (2) screws (4d).
4c
4d
SWITCH PLATE
SINGLE POLE DOUBLE POLE
FLUSH SWITCHASSEMBLY
SCREWS
Page 18 of 27939500486 Rev K
This step is applicable for Glass Selections only.
Removethis areaof plinth.
5a
5b
KEEPER SIDEPLINTH
SCREW
5a5b
HINGE SIDEPLINTH
SCREW
5. Install plinths to each side offrame (5a). Atttach using one (1)screw each (5b).
NOTE: Depending on heightadjustment of frame only one (1)screw may be used to fastenplinth to frame.
NOTE:When attaching a pivotdoor within a centerline 'L' or 'T'application, installer may have tomachine leg of plinth off.
6b
Page 19 of 27939500486 Rev K
6. Slide door seal into the door seal retainer (6a). On hinge side, apply door seal assembly at top and work downward (6b). On strike plate side, apply door seal strip in two (2) places (6c).
7. Ends of seal should fall neatly into place in plinth grooves.
6a
6c
6c
These steps are applicable for Glass Selections only.
7
REMOVE AREA ONDOOR SEAL RETAINER
FOR CLEARANCEOF TOP STRIKE
ASSEMBLY BRACKET
DOOR SEAL RETAINERREMOVED AND DOOR
SEAL INSTALLED INTOPLINTH
Page 20 of 27939500486 Rev K
Low Voltage Switch Installation
1. Attach watt stopper to J-box (1a). Route low voltage wire up through bottom of from or down from top of frame in full height scenerios only (1b).
2. Pull low voltage wire through opening and attach to quick connects (2a). Attach low voltage switch to quick connects (2b) and insert assembly into hole (2c) and snap into place.
3. Install plinth and seal asshown on pages 16 & 17,steps 5 through 7.
red
redblack
white
transformer
red
black
blue
light
120Vor
277V
24VCDswitch
WATT STOPPER
LOWVOLTAGE
WIRE
J-BOX
1a
1b
WARNING: All electrical installations should be doneby a qualified electrician in accordance with codes andregulations applicable at the installation site.
LOWVOLTAGESWITCH
QUICKCONNECTS
2c
2a
2b
LOW VOLTAGEWIRES
Page 21 of 27939500486 Rev K
DOOR(Ordered separatelyfrom frame unit.)
TRANSOMFRAME
40" IFFIELD ADDED
IF FIELD ADDEDPER HARDWAREREQUIREMENTS
INNER PLINTHASSEMBLIES
OUTER PLINTHS
HINGE(Quantity varies per door style)
STRIKE PLATE
FULL HEIGHT FRAME (KNOCK-DOWN)
TOP RAIL ASSEMBLY, TOP STRIKE ASSEMBLY, UPRIGHT (KEEPER SIDE) & UPRIGHT (HINGE SIDE).
DOOR SEAL
Butt-Hinged Door Components
DOOR HANDLE MORTISE HANDLE (LATCH VERSION)
(Ordered separately from frame unit.)
or
DOOR HANDLE MORTISE HANDLE (LOCK VERSION)
Page 22 of 27939500486 Rev K
TOP STRIKEASSEMBLY
TOP RAILASSEMBLY
FULL HEIGHTBUTT-HINGED DOOR FRAME ASSEMBLY
If you have a transom frame, start assembly on next page.
1. Install the top strike assembly on the outer door vertical on both sides, as shown, with four (4) #10-16 x 1/2" pan head self tapping screws provided.
2. Slide the top rail assembly into the top of the outer door vertical and line up holes on both sides. Install the top rail assembly with four (4) #10-16 x 1/2" pan head self tapping screws provided.
NOTE: Make sure to align the electrical pass through hole with the switch side of the frame.
NOTE: On a full height butt hinged door only, if the door gap appears too large. The split outer door vertical feature allows the top rail to telescope 1/2" from the top strike. Allowing the door frame to be positioned lower. On both sides remove the post extension assembly and loosen the fastener holding the top half of the upright. The telescoping inner horizontal can now be raised. Now reassemble.
TOP RAILASSEMBLY
TOP STRIKEASSEMBLY
12
OUTER DOORVERTICAL
OUTER DOORVERTICAL
ELECTRICALPASS THROUGH
HOLE
Page 23 of 27939500486 Rev K
OUTERDOORVERTICAL
3. Place the each inner plinth into the bottom of the outer door vertical as shown (3a & 3b). Attach each inner plinth to outer door vertical using two (2) bolts. Position each inner plinth 1/2" nominal from the bottom of the outer door vertical.
NOTE: With plinths mounted 1/2" below the door vertical, the result will be a 3/4" gapunder the door.
3a
OUTERDOOR
VERTICAL
INNERPLINTH
3bINNERPLINTH
NOMINAL POSITION1/2" PROTRUDED
NOMINAL POSITION1/2" PROTRUDED
Page 24 of 27939500486 Rev K
4
6
4. Lift frame up and align with panels.
5. Determine which outer door vertical must be moved upward to make the inner header assembly level horizontally. Tighten screws securing the outer door vertical.
6. Check for squareness bymeasuring the door opening.
5a
5b
Page 25 of 27939500486 Rev K
7. Peal off paper on back of seal (7a).
On hinge side, apply door seal onto the door seal retainer assembly at top and work downward (7b).
Repeat procedure for strike plate side (7c).
7a
7b
Strike Plate SideHinge Side
7c
PAPER
SEAL
DOOR SEALRETAINER
Page 26 of 27939500486 Rev K
8. Install outer plinths using screws provided.
Page 27 of 27939500486 Rev K
9. Install strike plate to the inner door vertical (strike side) with the two (2) #10-16 x 1/2" flat head screws provided.
10. Install hinges to hinge side (9a). Attach using the four (4) #10-16 x 1/2" flat head screws provided.
11. Attach door to hinges.
12. Assemble door hardware (Ordered separately from frame unit.)
9a
10a
11
STRIKE PLATE
9b
10b