1
Perimeter Trough for Heating and Cooling The trough style unit is designed to deliver both cooling and heating to the space. In cooling mode, the dampers open to allow conditioned air to exit out of the linear bar grill. The trough style unit is designed to deliver both cooling and heating to the space. In heating mode, the dampers close and the fin tube energizes and heats up. The cool air from the perimeter glass travels down one side of the trough and warm air moves out into the space through the other side of the trough. Fin Tube Off Air Plenum Damper Open Fin Tube On Air Plenum Damper Closed Perimeter Trough Style Unit (cooling mode) Perimeter Trough Style Unit (heating mode) A Perimeter Trough provides a method to both heat and cool a building’s perimeter within the same housing for maximum efficiency and plenum utilization. The standard trough is designed to house a 4-1/4” field sup- plied fin tube for heating which directs a steady flow of warm air to the building’s skin. The air is directed through an alu- minum linear bar grille along the building perimeter. For optional cooling, the trough is available with flanged rectan- gular or circular openings for introduction of conditioned air. Custom configurations are available upon request but please be very specific in your requirements. For ease of installation, the trough is self supported by stan- dard flat head pedestals which are locked into position on the bottom of the housing. This allows the trough to be installed before the access floor is installed to facilitate plumbing and other contracting. With the increased focus on underfloor air and indoor air quality, we are very excited about the opportunity to intro- duce new products such as this and further promote the use of underfloor air and access flooring. To receive more information on Tate’s Perimeter Trough, in Canada please contact Tate’s Technical Hotline at 800-231- 7788 all other inquires should contact Pedro Bermudez at: 913-312-1100 ext. 310, [email protected] or visit us online at: www.tateaccessfloors.com 3/4” x 3/8” Closed Cell Gasket Seal with Tape or Foam Cut Access Floor Panel Housing Fin Tube Holder 3.00” Tray Pedestal Support Caulk at Wall 3/4” x 3/8 Closed Cell Gasket Bae Stabilizer Bae 10” 1/4” without Carpet Tile 10” Bar Grille Support Pedestal Field Supplied Fin Tube Tate’s Perimeter Trough Features: Both heating and cooling capabilities Attractive Liner bar grill around perimeter Self supporting pedestal Quick easy installation Accommodates hot water or electric fin tube heating Allows for underfloor plenum VAV or cold water cooling 7510 Montevideo Rd. Jessup, MD 20794 800-231-7788 • [email protected]www.tateaccessfloor.com

Prime Tert Rough Slick

Embed Size (px)

DESCRIPTION

hvac

Citation preview

Page 1: Prime Tert Rough Slick

Perimeter Trough for Heating and Cooling

The trough style unit is designed to deliver both cooling andheating to the space. In cooling mode, the dampers opento allow conditioned air to exit out of the linear bar grill.

The trough style unit is designed to deliver both cooling andheating to the space. In heating mode, the dampers close andthe fin tube energizes and heats up. The cool air from theperimeter glass travels down one side of the trough and warmair moves out into the space through the other side of the trough.

Fin Tube Off

Air PlenumDamper Open

Fin Tube On

Air PlenumDamper Closed

Perimeter Trough Style Unit(cooling mode)

Perimeter Trough Style Unit(heating mode)

A Perimeter Trough provides a method to both heat and coola building’s perimeter within the same housing for maximumefficiency and plenum utilization.

The standard trough is designed to house a 4-1/4” field sup-plied fin tube for heating which directs a steady flow of warmair to the building’s skin. The air is directed through an alu-minum linear bar grille along the building perimeter. Foroptional cooling, the trough is available with flanged rectan-gular or circular openings for introduction of conditioned air.Custom configurations are available upon request but pleasebe very specific in your requirements.

For ease of installation, the trough is self supported by stan-dard flat head pedestals which are locked into position onthe bottom of the housing. This allows the trough to beinstalled before the access floor is installed to facilitateplumbing and other contracting.

With the increased focus on underfloor air and indoor airquality, we are very excited about the opportunity to intro-duce new products such as this and further promote the useof underfloor air and access flooring.

To receive more information on Tate’s Perimeter Trough, inCanada please contact Tate’s Technical Hotline at 800-231-7788 all other inquires should contact Pedro Bermudez at:913-312-1100 ext. 310, [email protected] orvisit us online at: www.tateaccessfloors.com

3/4” x 3/8” Closed Cell Gasket

Seal with Tape or Foam

Cut Access Floor Panel

Housing

Fin Tube Holder

3.00”

Tray Pedestal Support

Caulk at Wall

3/4” x 3/8 ClosedCell Gasket

Ba�e Stabilizer

Ba�e

10”

1/4” without Carpet Tile10” Bar Grille

Support Pedestal

Field Supplied Fin Tube

Tate’s Perimeter Trough Features:

• Both heating and cooling capabilities

• Attractive Liner bar grill around perimeter

• Self supporting pedestal

• Quick easy installation

• Accommodates hot water or electric fin tube heating

• Allows for underfloor plenum VAV or cold water cooling

7510 Montevideo Rd. Jessup, MD 20794 • 800-231-7788 • [email protected] • www.tateaccessfloor.com