Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
QMS 41953
PRICELIST 2018
ACCESORIESJointing Tray Type C 19Jointing Tray Type U 19Jointing Ladder Type W 19Jointing Ladder Type U 19Bracket 20Stand Plate 20Angle Connector 20Bracket Mounting 21Wall Bracket 21Hold Down Clip 21Hanger Beam 22Hanger Clevis 22Hold Down Clamp 22Cover Clip 23Cover Clamp 23Joggled Plate 24End Plate 24Raceway 25Separator 25Adjustable Splice Plate 25Horizontal Hinge fish Plate 25Vertical Hinge Fish Plate 25Horizontal Branch S. Plate 26Vertical Branch S. Plate 26Drop Out 26
TRAYTray Standard Type C 1Tray Economy Type U 2Horizontal Elbow Tray 3Inside Riser Tray 4Outside Riser Tray 5Tee Tray 6Cross Tray 7Reducer Tray 8
DUCTDuct Standard Type C 9Accesories Duct 10
LADDERLadder Standard Type W 11Ladder Economy Type U 12Horizontal Elbow Ladder 13Inside Riser Ladder 14Outside Riser Ladder 15Tee Ladder 16Cross Ladder 17Reducer Ladder 18
Tray Wiremesh 27Cable Duct PVC 28
CONTENT
QMS 41953
TRAY
Electro Galvanize & Hotdip Galvanize
Standard Type C
Tray Standard Type C Flange Cover Tray
A Cable Tray Section which has no range direction
Unit : mm
Thickness : 2 mm
Standard Length : 3.000 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
01
TRAY
Electro Galvanize & Hotdip Galvanize
Economy Type UA Cable Tray Section which has no range direction
Unit : mm
Thickness : 2 mm
Standard Length : 3.000 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
02
Tray Economy Type U Flange Cover Tray
QMS 41953
Horizontal Elbow
Electro Galvanize & Hotdip Galvanize
TRAY
Horizontal Elbow Tray Horizontal Bend Tray
A Cable Tray Section which changes direction in the same plane(left or right)
Unit : mm
Thickness : 2 mm
Standard Radius : 300 mm
Bend Angle : 90 degree
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
03
Tray
QMS 41953
Inside Riser
Electro Galvanize & Hotdip Galvanize
TRAY
Cover Inside Riser
An inside vertical elbow changes direction upward from thehorizontal plane
Unit : mm
Thickness : 2 mm
Standard Radius : 300 mm
Bend Angle : 90 degree
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
Inside Riser Tray
04
Tray
QMS 41953
Outside Riser
Electro Galvanize & Hotdip Galvanize
TRAY
Outside Riser Tray Cover Outside Riser
An outside vertical elbow changes direction downward from thehorizontal plane
Unit : mm
Thickness : 2 mm
Standard Radius : 300 mm
Bend Angle : 90 degree
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
05
Tray
QMS 41953
TRAYTee
Electro Galvanize & Hotdip Galvanize
Equal Tee Tray Unequal Tee Tray
Suitable for joining cable tray section in three direction at90 degree intervals in the same plane
Unit : mm
Thickness : 2 mm
Standard Radius : 300 mm
Bend Angle : 90 degree
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
06
Tray
QMS 41953
Cross
Electro Galvanize & Hotdip Galvanize
Equal Cross Tray Unequal Cross Tray
Suitable for joining cable tray section in four direction at90 degree intervals in the same plane
Unit : mm
Thickness : 2 mm
Standard Radius : 300 mm
Bend Angle : 90 degree
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
TRAY
07
Tray
QMS 41953
Equal / Unequal Cross Tray
Reducer
Electro Galvanize & Hotdip Galvanize
Straight Reducer Tray Left Reducer Tray Right Reducer Tray
Suitable for joining cable tray section of different widthin the same plane
Unit : mm
Thickness : 2 mm
Standard Length : 600 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
TRAY
08
Tray
QMS 41953
Duct
Electro Galvanize & Hotdip Galvanize
Duct Standard Type C Cover Duct
A cable tray section which has no range direction
Unit : mm
Thickness : 2 mm
Standard Length : 3.000 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
Standard Type C
09
QMS 41953
Accesories Duct
Electro Galvanize & Hotdip Galvanize
IR Duct Elbow Duct
Tee Duct Reducer Duct
Suitable for joining cable duct section
Unit : mm
Thickness : 2 mm
Standard Radius : 300 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
10
QMS 41953
Ladder
Electro Galvanize & Hotdip Galvanize
Ladder Standard Type W Cover Ladder
A cable tray section which has no range direction
Unit : mm
Thickness : 2 mm
Standard Length : 3.000 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
Standard Type W
11
QMS 41953
Ladder
Electro Galvanize & Hotdip Galvanize
Ladder Economy Type U Flange Cover Ladder
A cable tray section which has no range direction
Unit : mm
Thickness : 2 mm
Standard Length : 3.000 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
Economy Type U
12
QMS 41953
Horizontal Elbow
Electro Galvanize & Hotdip Galvanize
Horizontal Elbow Ladder Horizontal Bend Ladder
A cable tray section which changes direction in thesame plane (left or right)
Unit : mm
Thickness : 2 mm
Standard Radius : 300 mm
Bend Angle : 90 Degree
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
LADDER
13
Ladder
QMS 41953
Note : Horizontal Elbow Ladder available up to width = 600 mm
Horizontal Bend Ladder available to all width
Inside Riser
Electro Galvanize & Hotdip Galvanize
Inside Riser Ladder Cover Inside Riser
An inside vertical elbow changes direction upwardfrom the horizontal plane
Unit : mm
Thickness : 2 mm
Standard Radius : 300 mm
Bend Angle : 90 Degree
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
LADDER
14
Ladder
QMS 41953
Outside Riser
Electro Galvanize & Hotdip Galvanize
Outside Riser Ladder Cover Outside Riser
An outside vertical elbow changes direction downwardfrom the horizontal plane
Unit : mm
Thickness : 2 mm
Standard Radius : 300 mm
Bend Angle : 90 Degree
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
LADDER
15
Ladder
QMS 41953
LADDERTee
Electro Galvanize & Hotdip Galvanize
Equal Tee Ladder Unequal Tee Ladder
A cable tray section which suitable for joining cable tray section in three direction at 90 degree intervals in the same plane
Unit : mm
Thickness : 2 mm
Standard Radius : 300 mm
Bend Angle : 90 Degree
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
16
Ladder
QMS 41953
Cross
Electro Galvanize & Hotdip Galvanize
Equal Cross Ladder Unequal Cross Ladder
A cable tray section which Suitable for joining cable tray section in four direction at 90 degree intervals in the same plane
Unit : mm
Thickness : 2 mm
Standard Radius : 300 mm
Bend Angle : 90 Degree
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
17
LADDER
Ladder
QMS 41953
Reducer
Electro Galvanize & Hotdip Galvanize
Straight Reducer Ladder
Left Reducer Ladder
Right Reducer Ladder
A cable tray section which Suitable for joining cable tray section of different width in the same plane
Unit : mm
Thickness : 2 mm
Standard Length : 600 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
18
LADDER
Ladder
QMS 41953
Accesories Tray & Ladder
Electro Galvanize & Hotdip Galvanize
A cable tray connector is a device which joins cable tray bystraight section and or fittings
Unit : mm
Thickness : 2 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
19
Hotdip Galvanized
QMS 41953
A cable tray bracket is a device which provides adequate means for supporting cable tray straight section or fittings
Unit : mm
Thickness : 2 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
20
QMS 41953
Bracket
Accesories Tray & Ladder
Electro Galvanize & Hotdip Galvanize
A cable tray connector is a device which joins cable tray bystraight section and or fittings
Unit : mm
Thickness : 2 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
21
QMS 41953
Accesories Tray & Ladder
Electro Galvanize & Hotdip Galvanize
A cable tray connector is a device which joins cable tray bystraight section and or fittings
Unit : mm
Thickness : 2 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
22
QMS 41953
Accesories Tray & Ladder
Electro Galvanize & Hotdip Galvanize
A cable tray connector is a device which joins cable tray bystraight section and or fittings
Unit : mm
Thickness : 2 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
23
QMS 41953
Accesories Tray & Ladder
Electro Galvanize & Hotdip Galvanize
A cable tray connector is a device which joins cable tray bystraight section and or fittings
Unit : mm
Thickness : 2 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
24
QMS 41953
Accesories Tray & Ladder
Electro Galvanize & Hotdip Galvanize
A cable tray connector is a device which joins cable tray bystraight section and or fittings
Unit : mm
Thickness : 2 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
Offered to adjust a tray run for changes in direction in a horizontal plane (right or left) that do not conform to standard horizontal fittings
This plate provide for changes in elevation upward or downward that do not conform to standard vertical fittings
25
QMS 41953
Accesories Tray & Ladder
Electro Galvanize & Hotdip Galvanize
A cable tray connector is a device which joins cable tray bystraight section and or fittings
Thickness : 2 mm
Material : Hot Rolled Miled Steel Sheet (SPHC)
(Other finishing, sizes & specification available on request)
26
QMS 41953
Accesories Tray & Ladder
Electro Galvanize & Hotdip Galvanize
A cable tray connector is a device which joins cable tray bystraight section and or fittings
27
Tray Wiremesh Standard Length : 3.000 mm
Wire Diameter : 5 mm
Material : Low Carbon Steel
QMS 41953
Also known as Cable Cage or Tray BRC
ELECTRO
Electro Galvanize & Hotdip Galvanize
28
Cable Duct PVC Standard Length : 3.000 mm
Material : PVC
Color : White
QMS 41953