Upload
sterling-shipler
View
245
Download
1
Tags:
Embed Size (px)
Citation preview
PPPoA Test Configuration
Example on IDL-4800 to ADE-4400 / 3rd party device
2 / 22
PPPoA Test Configuration
ASUS AM_604g
PPPoA connection enabled
DHCP Server enabled
Uplink BP:
VLAN-2, tagged IF
Untagged IF
PVID-2
IP: Dynamic IP
PPP server
PC#1
VLAN-2 tagged IF
xDSL-1, PVC-1:
PVID-2, Untagged
ADE-4400
PPPoA connection enabled
DHCP Server enabled
3 / 22
PPPoA Test Configuration
PPPoE/PPPoA Server
IP DSLAM
Modem
Modem
L2 Switch
PPPoE / PPPoA serverUbuntu + PPPoE server
IP DSLAMIDL-4800
ModemADSL CPE
4 / 22
1. Make sure your PPP service on the Server is running.
2. Configures DSLAM to have a proper setting.
3. Configures the ADSL Modem (ex: ADE-4400 & ASUS AM_604g)
4. Configures your switch and make sure all VLAN setting is correct.
5. Verify traffic path of PPPoA connection.
Steps for the PPPoA test
5 / 22
DSLAM configuration
6 / 22
management mgmt 172.16.9.44 netmask 255.255.255.0management gbe 192.168.100.1 netmask 255.255.255.0route default 172.16.9.254snmp 1 community rw "public"igmp version v2igmp snoopinginterface gigabit 1 bridge default vlan 1 egress untag vlan 2 priority reserved tag isolationinterface gigabit 2 bridge default vlan 1 egress untaginterface xdsl 1 adsl-config line status service on bridge 1 pvc 0/35 pvc encapsulation auto default vlan 2 egress untaginterface xdsl 2 adsl-config line status service on bridge 1 pvc 0/35 pvc encapsulation auto default vlan 2 egress untagcluster-cfg name "u71577C"bye
< running config >
IDL-4800 DSLAM running config
7 / 22
Note: For the PPPoA application , please configure ADSL PVC encapsulation mode as “Auto”
IDL-4800 DSLAM running config
8 / 22
Example device:PLANET ADE-4400 configuration
9 / 22
1. Click Network WAN
2. Key in the parameters VPI: 0 VCI:35 according to DSLAM’s setting
3. Select VC-Mux (or LLC) for encapsulation
4. Select PPPoA
5. Enable NAPT
6. Key in User Name / Password
7. And then ADD to add the channel
8. Save the Configuration
Configuration on PLANET ADE-4400
10 / 22
Example device:ASUS AM_604g configuration
11 / 22
Configuration on ASUS AM_604g
1. Click Advanced Setup WAN
2. Click Add Button
12 / 22
Configuration on ASUS AM_604g (Cont.)
Input your VPI and VCI number
13 / 22
Configuration on ASUS AM_604g (Cont.)
Select connection type and encapsulation mode VCMUX or LLC for PPPoA
14 / 22
Configuration on ASUS AM_604g (Cont.)
1. Input your PPP Username and Password for PPPoA connection
2. Click Next Button
15 / 22
Configuration on ASUS AM_604g (Cont.)
16 / 22
Configuration on ASUS AM_604g (Cont.)
Click Save Button
17 / 22
Configuration on ASUS AM_604g (Cont.)
Click Finish button
18 / 22
Configuration on ASUS AM_604g (Cont.)
1. Click Advance Setup Routing Default Gateway
2. Select Enable Automatic Assigned Default Gateway check box
3. Click Save/Apply button
19 / 22
Configuration on ASUS AM_604g (Cont.)
1. Click Advance Setup LAN
2. Select Enable DHCP Server check box
3. Click Save/Reboot button
Save/ Reboot
20 / 22
PPPoA Status on ASUS AM_604g
If PPPoA works and all the settings of PPP server, DSLAM, and CPE are correct, the WAN Info of CPE will show status is ‘Up’ and PPP server will assign an IP to this CPE.
21 / 22
Verify traffic path of PPPoA connection
22 / 22
LAN/ WAN
ASUS AM_604g
PPPoA connection enabled
DHCP Server enabled
Uplink BP:
VLAN-2, tagged IF
Untagged IF
PVID-2
IP: Dynamic IP
PPP server
PC#1
VLAN-2 tagged IF
xDSL-1, PVC-1:
PVID-2, Untagged
PC#2
After PPP session is established, PC#1 can access the same LAN (PC#2) as PPP server and internet (WAN, depends on PPP server setting.) for testing.
PPPoA Verification
ADE-4400
PPPoA connection enabled
DHCP Server enabled
23 / 22