Embed Size (px)
DESCRIPTION
32
Citation preview
POWER PLANTMOUNT
32-1
POWER PLANTMOUNT
CONTENTS
ENGINE MOUNTING 2. . . . . . . . . . . . . . . . . . . . . . . TRANSMISSION MOUNTING 3. . . . . . . . . . . . . . . .
POWER PLANT MOUNT – Engine Mounting32-2
ENGINE MOUNTINGREMOVAL AND INSTALLATIONCautionProvisionally tighten the parts marked by an asterisk (*), and then fully tighten after loading thefull weight of the engine on the vehicle body.
Pre-removal and Post-installation OperationCrossmember Removal and Installation (Refer toGROUP 33.)
25 Nm*
2
44 Nm 44 Nm 25 Nm*
25 Nm
25 Nm
2
1
Removal steps1. Engine mount bracket2. Engine mount insulator
POWER PLANT MOUNT – Transmission Mounting 32-3
TRANSMISSION MOUNTINGREMOVAL AND INSTALLATIONCautionProvisionally tighten the parts marked by an asterisk (*), and then fully tighten after loading thefull weight of the transmission on the vehicle body.
Pre-removal and Post-installation OperationJack up the Engine and Transmission Assembly untilthere is no weight on the Engine Mount Bracket Insulator.
93 Nm*
3
49 Nm
49 Nm
49 Nm
2
14
7
5
6
Removal steps1. Washer2. Spacer3. Transmission mount bushing4. Transmission mount crossmember
assembly
5. Transmission mount insulator assembly�A� 6. Transmission mount stopper
7. Adaptor
INSTALLATION SERVICE POINT�A� TRANSMISSION MOUNT STOPPER INSTALLATIONInstall the transmission mount stopper so that the arrow facesthe direction shown.
NOTEDisregard F and R stamped as a shared part.
Transmissionmount stopper
Front of vehicle
Transmissionmount insula-tor assembly
NOTES
POWER PLANT MOUNT – General/Engine Mounting 32-1
GROUP 32
POWER PLANT MOUNTGENERALOUTLINE OF CHANGEThe following service procedures have been added due to the change of the engine mount and transmissionmount.
ENGINE MOUNTINGREMOVAL AND INSTALLATION
Pre-removal and Post-installation OperationCrossmember Removal and Installation
1
2
3
4
49 Nm
49 Nm
49 Nm
49 Nm
49 Nm49 Nm
49 Nm
Removal steps1. Engine mount insulator Assembly
(L.H.)2. Engine mount insulator Assembly
(R.H.)
3. Engine mount bracket (L.H.)4. Engine mount bracket (R.H.)
POWER PLANT MOUNT – Transmission Mounting32-2
TRANSMISSION MOUNTINGREMOVAL AND INSTALLATION
Pre-removal and Post-installation OperationJack up the Engine and Transmission Assembly untilthere is no weight on the Engine Mount Bracket Insulator.
1
3
4
4
2
2
49 Nm
49 Nm
49 Nm
49 Nm
49 Nm
<A/T>
<M/T>
1
Removal steps1. Collar2. Transmission mount bushing3. Transmission mount crossmember
Assembly
4. Transmission mount insulator Assembly
POWER PLANT MOUNT – General/Engine Mounting 32-1
GROUP 32
POWER PLANT MOUNTGENERALOUTLINE OF CHANGEThe following service procedures have been established due to the addition of vehicles with 4G9-MPIengine. The other service procedures are the same as the vehicles with GDI engine.
ENGINE MOUNTINGREMOVAL AND INSTALLATION
CautionProvisionally tighten the parts marked by an asterisk (*), and then fully tighten after loading thefull weight of the engine on the vehicle body.
Pre-removal and Post-installation OperationCrossmember Removal and Installation (Refer to GROUP 33.)
2
1
49 ± 10 N·m
26 ± 5 N·m*
49 ± 10 N·m
Removal steps1. Engine mount bracket <RH>2. Engine mount insulator
NOTES
