Power flexibles - Elec.ru

SEE ON PAGE 11

SEE ON PAGE 12

SEE ON PAGE 10

SEE ON PAGE 8-9

SEE ON PAGE 4

>Power flexiblesPOWER SHUNTS

FLEXIBAR®

FLEXIBAR® SUPPORTS AND SPACER CLAMPS

ELECTRO-HYDRAULIC TOOLS

MANUAL TOOLS

3

Powe

r fle

xibl

es

R

HIGH FLEXIBILITYLARGE RANGE IN SECTION AND LENGTHINTENSITY : UP TO 4600 A

Power shunts>

PBC PPSBRAIDED POWER SHUNTS• Undrilled palms to customer's specific designs, fitted by power press• Extra-flexible power connections (expansion rings, busbar…)• Tinned electrolytic copper strand Ø 0,15 mm• When used in parallel, the 2 shunts must be spaced with a minimum distance

equal to the thickness of the shunt to allow air cooling

PRESSWELDED POWER SHUNTSPress welding is the welding of laminations to each other through direct current applied to pieces under pressure.This technique results in:• The formation of a solid palm with properties of plain bar• Smaller cross section for same capacity• Runs cooler than an equal section• Plain copper, thickness of laminations 0.3 mm• When used in parallel, the 2 shunts must be

spaced with a minimum distance equal to the thickness of the shunt

PBC PPS

MBJ

PAGE 43

4

Powe

r fle

xibl

es

PBC 100 x 250 564000 100 349 600 462 795 35 40 7,0 250 2 0,38PBC 100 x 500 564050 100 349 600 462 795 35 40 7,0 500 2 0,63PBC 120 x 250 564010 120 385 670 511 877 35 40 7,5 250 2 0,42PBC 120 x 500 564020 120 385 670 511 877 35 40 7,5 500 2 0,72PBC 150 x 250 564100 150 440 757 583 1003 55 50 8,0 250 2 0,63PBC 150 x 500 564150 150 440 757 583 1003 55 50 8,0 500 2 0,90PBC 200 x 250 564200 200 550 946 729 1253 55 50 9,0 250 2 0,76 PBC 200 x 500 564250 200 550 946 729 1253 55 50 9,0 500 2 1,20PBC 250 x 300 564300 250 651 1120 863 1484 85 50 10,5 300 2 1,03PBC 250 x 600 564350 250 651 1120 863 1484 85 50 10,5 600 2 1,77 PBC 300 x 400 564400 300 716 1180 948 1565 85 60 11,0 400 1 1,53PBC 400 x 400 564500 400 853 1360 1131 1808 85 80 11,0 400 1 2,20PBC 500 x 400 564600 500 917 1561 1216 1944 105 100 11,0 400 1 2,64PBC 600 x 450 564700 600 1101 1762 1459 2334 105 100 12,0 450 1 3,4PBC 800 x 450 564800 800 1376 2202 1823 2917 105 100 15,0 450 1 4,26PBC 1000 x 450 564900 1000 1651 2642 2188 3500 105 100 18,0 450 1 5,47PBC 1200 x 500 564030 1200 1982 3170 2626 4208 125 120 17,5 500 1 7,16

DESCRIPTION

Intensity Intensity L

Part Section (∆T 30°K) (∆T 50°K) A B C N° mm2 mm mm mm mm

PPS 40/5/50-180 566000 200 572 984 758 1304 50 40 5 180 45 2 0,390 PPS 40/5/50/220 566010 200 572 984 758 1304 50 40 5 220 52 2 0,475

PPS 40/10/50-220 566020 400 849 1460 1125 1935 50 40 10 220 58 2 0,930PPS 50/10/80-280 566030 500 1022 1758 1354 2329 80 50 10 280 58 1 1,440PPS 80/10/100-320 566040 800 1511 2493 2002 3303 100 80 10 320 52 1 2,625PPS 100/10/100-300 566050 1000 1825 2920 2418 3869 100 100 10 300 54 1 3,065PPS 100/10/110-360 566060 1000 1825 2920 2418 3869 110 100 10 360 53 1 3,610PPS 100/15/110-360 566070 1500 2178 3485 2886 4617 110 100 15 360 57 1 5,385

DESCRIPTION

Intensity Intensity Part Section (∆T 30°K) (∆T 50°K) A B C L H N° mm2

mm mm mm mm mm

R

>FLEXIBAR®

the most flexible busbar

What is FLEXIBAR ® ?AN EXCEPTIONAL CONDUCTORFLEXIBAR® consists of a stack of electrolytic copper laminates protected within a durable PVC insulation.Internal copper laminates are free to slide within the insulation, offering unlimited twisting and bending possibilities for panelboard assembly. Terminals are created by stripping the insulation and punching the laminates ; the cost of lugs and associated labour is eliminated.FLEXIBAR® is the modern and cost effective alternative for electrical connections in switchboards and control panels.

THE MOST FLEXIBLE OF FLEXIBLE BUSBARSThe extreme flexibility which characterises FLEXIBAR®, is obtained by ERICO’s exclusivemanufacturing process, which results in :- laminations being centralised and free to slide within the sleeve- constant insulation thickness over the whole surface, with perfect corners.

The PVC insulation is a high resistance vinyl compound, self-extinguishing, according to UL 1581

Traceability code

DesignationPart number

FLEXIBAR® connections are made by punching

directly through the laminates.

No lugs to purchase, installation is simpler and faster, and faulty

connection problems are eliminated.

FLEXIBAR® is formed with multiple layers of thin, tin-plated or plain, electrolytic copper.

Easily formed, FLEXIBAR® improves assembly flexibility, and aesthetics of panels.

5

Powe

r fle

xibl

es

R

6

Specific advantagesof FLEXIBAR ®

Preformed Solutions

WEIGHT AND VOLUME SAVINGS OF YOUR PANELSERICO's exclusive manufacturing process results in a minimal bending radius, allowing unlimited twisting and bending possibilities. Moreover, for the same current, FLEXIBAR® has a cross section 40% lower than a cable.

DESIGN TIME SAVINGFLEXIBAR®'s flexibility improves design flexibility.

ASSEMBLY TIME SAVINGThe easy stripping of the insulation and the elimination of lugs results in quick, easy and cost effective connections.

IMPROVES AESTHETICS AND PROFESSIONAL APPEARANCE OF PANELSEasily formed, FLEXIBAR® holds its shape.

IMPROVES THE SAFETY AND THE RELIABILITY OF YOUR PANELS• By reducing the number of connections cables/

lugs (less potential hot spots).• By guaranteeing constant insulation thickness,

including the corners.• Because each piece has undergone a test of

dielectric strength at 20000 volts.All these advantages have made FLEXIBAR® the preferred flexible bar for panelboard designers and assemblers throughout the world.

Volume- 25%

CABLE

FLEXIBAR®

- 30%

FLEXIBAR®

BUSBAR

- 40%

CABLE

FLEXIBAR®

Time savingand efficiency

FLEXIBAR® tooling foroptimum use of FLEXIBAR® :

Stripper

Bender

Twister PunchHydraulic shearer

Manual shearer

ERICO® can provide preformedFLEXIBAR® connections to customer'sdrawings.FLEXIBAR® can be cut, punched-twisted or bent to address the most challengingpanelboard designs and productionscheduling requirements

New ! FLEXIFORM SOFTWAREStarting with basic shapes, as well as with your sizes, lengths, divisions, drillings, hole size…FLEXIFORM software allows you to :- Directly calculate a pricerange for your preformed FLEXIBAR®

- Print an explanatory sheet

1 2 3 4 5 6 7

STANDARD SHAPES

DRILLING TYPES

G H I J K L M

A B C D E F

6

Powe

r fle

xibl

es

R

ApplicationsAll types of connections on low voltage industrial power distribution and control.• Alternative to large and small cables.• Alternative to rigid busbar sets.• Connections between a main busbar

and distribution equipment (contactors, circuit-breakers, switches…).

• Connections between a transformer and a bus-duct.

• Connections between a bus-duct and an electrical cabinet.

• Expansion joint.

7

Powe

r fle

xibl

es

R

A N A B 8 x 6 x 0,5 552400 24 196 182 166 143 128 1,72 2,25 3 x 9 x 0,8 552410 21,6 158 147 134 120 104 1,72 2,25 6 x 9 x 0,8 552420 43,2 290 269 245 220 190 1,72 2,25 3 x 13 x 0,5 552440 19,5 198 184 167 150 130 1,72 2,25 2 x 15,5 x 0,8 552390 24,8 252 234 212 191 165 1,72 2,25 9 x 9 x 0,8 552430 64,8 314 291 265 237 206 1,72 2,25 6 x 13 x 0,5 552450 39 300 277 253 226 196 1,72 2,25 4 x 15,5 x 0,8 552460 49,6 380 350 320 286 248 1,72 2,25 2 x 20 x 1 552490 40 326 300 275 246 214 1,72 2,25 3 x 20 x 1 552500 60 428 395 360 323 280 1,72 2,25 2 x 24 x 1 552550 48 450 416 380 340 295 1,72 2,25 6 x 15,5 x 0,8 552470 74,4 476 440 402 360 318 1,72 2,25 10 x 15,5 x 0,8 552480 124 538 498 455 407 352 1,72 2,25 4 x 20 x 1 552510 80 476 440 402 360 312 1,72 2,25 5 x 20 x 1 552520 100 498 460 420 376 326 1,72 2,25 6 x 20 x 1 552530 120 546 506 462 413 358 1,72 2,25 3 x 24 x 1 552560 72 490 453 413 370 320 1,72 2,25 4 x 24 x 1 552570 96 550 540 465 416 360 1,72 2,25 2 x 32 x 1 552620 64 480 445 406 363 315 1,72 2,25 3 x 32 x 1 552630 96 570 525 480 430 372 1,72 2,25 2 x 40 x 1 552690 80 538 500 455 406 352 1,72 2,25 5 x 24 x 1 552580 120 608 563 514 460 398 1,72 2,25 6 x 24 x 1 552590 144 670 620 566 506 438 1,72 2,25 4 x 32 x 1 552640 128 648 600 548 490 425 1,72 2,25 3 x 40 x 1 552700 120 617 570 522 466 405 1,72 2,25 4 x 40 x 1 552710 160 727 673 615 550 476 1,72 2,25 3 x 50 x 1 552760 150 700 650 592 530 460 1,72 2,25 10 x 20 x 1 552540 200 762 706 645 576 500 1,72 2,25 8 x 24 x 1 552600 192 802 743 678 606 525 1,72 2,25 5 x 32 x 1 552650 160 758 702 640 573 496 1,72 2,25 6 x 32 x 1 552660 192 846 783 715 640 555 1,72 2,25 5 x 40 x 1 552720 200 900 832 760 680 590 1,72 2,25 4 x 50 x 1 552770 200 860 795 727 650 563 1,72 2,25 3 x 63 x 1 552820 189 798 740 675 603 522 1,65 2,12

CHARACTERISTICS• CONDUCTOR IN ELECTROLYTIC COPPER

• INSULATION IN HIGH RESISTANCE VINYL COMPOUND :elongation : 370 %,max. working temperature : 105°C,thickness : 2 mm ± 0,2, self-extinguishing : UL 94 VO, dielectric strength : 20kV/mm, working voltage ≤1000 V AC / 1500 V DC.

FLEXIBAR ® / technical characteristics> Temperature rise of conductor = T

2 - T

1 = � T (°K) With T

2 max = 105°C

SELECTION OF FLEXIBAR ACCORDING TO THE INTERNAL TEMPERATURE OF THE PANEL

Ex. : For a current of 630A, withT1 = 40°C - T2 = 90°C

� T = 90 - 40 = 50°K

� In the 50°C column, find the closest current value to 630A.

FLEXIBAR® 5 x 32 x 1 - 552650 - 160 mm2 - 640A

� Select FLEXIBAR® according to the terminal width of the equipment being connected.

AmbientTemperature

Temperature of conductors (T2)

Internaltemperature of panel (T1)

ADMISSIBLE CURRENTS : This table indicates the temperature rise produced by chosen current in the given section.This calculation does not take into account the heat dissipation from the switchgear.

Sectionmm2N° � T (°k) � T (°k)

70 60 50 40 30 70 60 50 40 30

CURRENTCOEFFICIENT Section

mm2N°CURRENT

COEFFICIENTA

125

A25

0 A

400

A50

0 A

630

A

N A B 10 x 24 x 1 552610 240 948 877 800 716 592 1,72 2,25 8 x 32 x 1 552670 256 1018 943 860 770 667 1,72 2,25 6 x 40 x 1 552730 240 1018 943 860 770 667 1,72 2,25 5 x 50 x 1 552780 250 1100 1016 930 830 718 1,72 2,25 4 x 63 x 1 552830 252 1010 935 855 763 661 1,65 2,12 3 x 80 x 1 552880 240 980 906 827 740 640 1,65 2,12 10 x 32 x 1 552680 320 1230 1140 1040 930 805 1,72 2,25 8 x 40 x 1 552740 320 1230 1140 1040 930 805 1,72 2,25 10 x 40 x 1 552750 400 1400 1295 1181 1055 915 1,72 2,25 6 x 50 x 1 552790 300 1225 1135 1035 925 802 1,72 2,25 8 x 50 x 1 552800 400 1393 1290 1175 1050 912 1,72 2,25 5 x 63 x 1 552840 315 1220 1125 1030 920 797 1,65 2,12 6 x 63 x 1 552850 378 1437 1330 1215 1085 941 1,65 2,12 4 x 80 x 1 552890 320 1200 1110 1015 906 785 1,65 2,12 5 x 80 x 1 552900 400 1390 1285 1175 1050 910 1,65 2,12 4 x 100 x 1 552940 400 1446 1340 1225 1093 947 1,60 2,02 10 x 50 x 1 552810 500 1650 1525 1395 1245 1080 1,72 2,25 8 x 63 x 1 552860 504 1650 1525 1395 1245 1080 1,65 2,12 6 x 80 x 1 552910 480 1627 1505 1375 1230 1065 1,65 2,12 5 x 100 x 1 552950 500 1635 1515 1385 1235 1070 1,60 2,02 6 x 100 x 1 552960 600 1843 1705 1550 1393 1205 1,60 2,02 10 x 63 x 1 552870 630 1895 1755 1600 1435 1240 1,65 2,12 8 x 80 x 1 552920 640 1895 1755 1600 1430 1240 1,65 2,12 10 x 80 x 1 552930 800 2100 1945 1775 1585 1375 1,65 2,12 8 x 100 x 1 552970 800 2147 1990 1815 1625 1405 1,60 2,02 10 x 100 x 1 552980 1000 2350 2170 1985 1775 1535 1,60 2,02 12 x 100 x 1 552990 1200 2500 2315 2115 1890 1636 1,60 2,02 10 x 120 x 1 538650 1200 2755 2550 2330 2070 1792 1,49 1,95

800

A10

00 A

1250

A16

00 A

>

When using 2 or 3 FLEXIBAR® in parallel, use the coefficient :Ex : 5 x 32 x 1 — � t° = 50° K : 640 A2 bars in parallel ➜ 640 A x 1,72 = 1100 A3 bars in parallel ➜ 640 A x 2,25 = 1440 A

2M 2M

8

Powe

r fle

xibl

es

R

WEIGHT AND VOLUME SAVINGSDESIGN & ASSEMBLY TIME SAVINGAESTHETIC APPEARANCESAFE AND RELIABLE

FLEXIBAR ® / the range>

FLEXIBAR® 2M FLEXIBAR® 3MPLAIN COPPER• Length 2 metres

PLAIN COPPER• Length 3 metres

FLEXIBAR® 3MTCTINNED COPPER• Length 3 metres

FLEXIBAR 3M 6 x 9 x 0,8 541020 5 1,22 FLEXIBAR 3M 4 x 15,5 x 0,8 541060 5 1,53 FLEXIBAR 3M 6 x 15,5 x 0,8 541070 5 2,25FLEXIBAR 3M 2 x 20 x 1 541090 5 1,58FLEXIBAR 3M 3 x 20 x 1 541100 5 2,13FLEXIBAR 3M 4 x 20 x 1 541110 5 2,67FLEXIBAR 3M 2 x 24 x 1 541150 5 1,86FLEXIBAR 3M 3 x 24 x 1 541160 5 2,52FLEXIBAR 3M 4 x 24 x 1 541170 5 3,18FLEXIBAR 3M 5 x 24 x 1 541180 5 3,83FLEXIBAR 3M 3 x 32 x 1 541230 2 3,30 FLEXIBAR 3M 4 x 32 x 1 541240 2 4,17 FLEXIBAR 3M 5 x 32 x 1 541250 2 5,04FLEXIBAR 3M 6 x 32 x 1 541260 2 5,91FLEXIBAR 3M 8 x 32 x 1 541270 2 7,65FLEXIBAR 3M 3 x 40 x 1 541300 2 4,08FLEXIBAR 3M 5 x 40 x 1 541320 2 6,24FLEXIBAR 3M 5 x 50 x 1 541380 2 7,76

DESCRIPTION Part N° Length 3 m

FLEXIBAR 3MTC 6 x 9 x 0,8 544320 5 1,22FLEXIBAR 3MTC 2 x 15,5 x 0,8 544330 5 0,77 FLEXIBAR 3MTC 4 x 15,5 x 0,8 544360 5 1,53 FLEXIBAR 3MTC 6 x 15,5 x 0,8 544370 5 2,25FLEXIBAR 3MTC 2 x 20 x 1 544390 5 1,58FLEXIBAR 3MTC 3 x 20 x 1 544400 5 2,13FLEXIBAR 3MTC 4 x 20 x 1 544410 5 2,67FLEXIBAR 3MTC 5 x 20 x 1 544420 5 3,22FLEXIBAR 3MTC 2 x 24 x 1 544450 5 1,86FLEXIBAR 3MTC 3 x 24 x 1 544460 5 2,52FLEXIBAR 3MTC 4 x 24 x 1 544470 5 3,18FLEXIBAR 3MTC 5 x 24 x 1 544480 5 3,83FLEXIBAR 3MTC 6 x 24 x 1 544490 2 4,48FLEXIBAR 3MTC 8 x 24 x 1 544500 2 5,80FLEXIBAR 3MTC 3 x 32 x 1 544530 2 3,30FLEXIBAR 3MTC 4 x 32 x 1 544540 2 4,17 FLEXIBAR 3MTC 5 x 32 x 1 544550 2 5,04FLEXIBAR 3MTC 6 x 32 x 1 544560 2 5,91FLEXIBAR 3MTC 8 x 32 x 1 544570 2 7,65FLEXIBAR 3MTC 10 x 32 x 1 544580 2 9,40FLEXIBAR 3MTC 3 x 40 x 1 544600 2 4,08FLEXIBAR 3MTC 4 x 40 x 1 544610 2 5,16FLEXIBAR 3MTC 5 x 40 x 1 544620 2 6,24FLEXIBAR 3MTC 5 x 50 x 1 544680 2 7,76FLEXIBAR 3MTC 8 x 50 x 1 544700 2 11,80FLEXIBAR 3MTC 5 x 63 x 1 544740 2 9,72FLEXIBAR 3MTC 8 x 63 x 1 544760 2 14,82


FLEXIBAR 8 x 6 x 0,5 552400 10 0,35FLEXIBAR 3 x 9 x 0,8 552410 10 0,43FLEXIBAR 6 x 9 x 0,8 552420 10 0,81FLEXIBAR 9 x 9 x 0,8 552430 10 1,19FLEXIBAR 3 x 13 x 0,5 552440 10 0,45FLEXIBAR 6 x 13 x 0,5 552450 10 0,79FLEXIBAR 2 x 15,5 x 0,8 552390 10 0,51FLEXIBAR 4 x 15,5 x 0,8 552460 10 1,02FLEXIBAR 6 x15,5 x 0,8 552470 10 1,50FLEXIBAR 10 x 15,5 x 0,8 552480 10 2,20FLEXIBAR 2 x 20 x 1 552490 5 1,05FLEXIBAR 3 x 20 x 1 552500 5 1,42FLEXIBAR 4 x 20 x 1 552510 5 1,78FLEXIBAR 5 x 20 x 1 552520 5 2,15FLEXIBAR 6 x 20 x 1 552530 5 2,41FLEXIBAR 10 x 20 x 1 552540 5 3,99FLEXIBAR 2 x 24 x 1 552550 5 1,24FLEXIBAR 3 x 24 x 1 552560 5 1,68FLEXIBAR 4 x 24 x 1 552570 5 2,12FLEXIBAR 5 x 24 x 1 552580 5 2,55FLEXIBAR 6 x 24 x 1 552590 5 2,99FLEXIBAR 8 x 24 x 1 552600 5 3,87FLEXIBAR 10 x 24 x1 552610 5 4,75FLEXIBAR 2 x 32 x 1 552620 5 1,62FLEXIBAR 3 x 32 x 1 552630 5 2,20FLEXIBAR 4 x 32 x 1 552640 5 2,78FLEXIBAR 5 x 32 x 1 552650 5 3,36FLEXIBAR 6 x 32 x 1 552660 5 3,94FLEXIBAR 8 x 32 x 1 552670 5 5,10FLEXIBAR 10 x 32 x 1 552680 5 6,27


FLEXIBAR 2 x 40 x 1 552690 5 1,99FLEXIBAR 3 x 40 x 1 552700 5 2,72FLEXIBAR 4 x 40 x 1 552710 5 3,44FLEXIBAR 5 x 40 x 1 552720 5 4,16FLEXIBAR 6 x 40 x 1 552730 5 4,89FLEXIBAR 8 x 40 x 1 552740 5 6,33FLEXIBAR 10 x 40 x 1 552750 5 7,78FLEXIBAR 3 x 50 x 1 552760 5 3,37FLEXIBAR 4 x 50 x 1 552770 5 4,27FLEXIBAR 5 x 50 x 1 552780 5 5,17FLEXIBAR 6 x 50 x 1 552790 2 6,07FLEXIBAR 8 x 50 x 1 552800 2 7,87FLEXIBAR 10 x 50 x 1 552810 2 9,68FLEXIBAR 3 x 63 x 1 552820 2 4,21FLEXIBAR 4 x 63 x 1 552830 2 5,34FLEXIBAR 5 x 63 x 1 552840 2 6,48FLEXIBAR 6 x 63 x 1 552850 2 7,61FLEXIBAR 8 x 63 x 1 552860 2 9,88FLEXIBAR 10 x 63 x 1 552870 2 12,14FLEXIBAR 3 x 80 x 1 552880 2 5,32FLEXIBAR 4 x 80 x 1 552890 2 6,75FLEXIBAR 5 x 80 x 1 552900 2 8,19FLEXIBAR 6 x 80 x 1 552910 2 9,62FLEXIBAR 8 x 80 x 1 552920 2 12,49FLEXIBAR 10 x 80 x 1 552930 2 15,37FLEXIBAR 4 x 100 x 1 552940 2 8,41FLEXIBAR 5 x 100 x 1 552950 2 10,20FLEXIBAR 6 x 100 x 1 552960 2 11,99FLEXIBAR 8 x 100 x 1 552970 2 15,57FLEXIBAR 10 x 100 x 1 552980 2 19,16FLEXIBAR 12 x 100 x 1 552990 2 22,74FLEXIBAR 10 x 120 x 1 538650 1 22,90


PAGE 56 PAGE 50TECH

NICA

L SE

CTIO

N

ES S

OFTW

ARE

ERIL

INK

ON REQUEST :FLEXIBAR® 4 METRES

9

Powe

r fle

xibl

es

R

EASE OF INSTALLATIONIMPROVE THE AESTHETICSOF THE PANELOPTIMISATION OF THE FLEXIBAR®

PERFORMANCE

FLEXIBAR ® / supports and spacer clamps>

UFS KITFLEXIBAR® SUPPORT Assembly comprises of a 2 m aluminium section and 24 retaining blocks in glass reinforced polyamide, halogen free.• It is possible to make up 3 supports,

650 mm long each for 4 FLEXIBAR®

• Recommended distance between supports :400 mm max.

UFS kit 553590 1 2,3

DESCRIPTION Part N°

FSFLEXIBAR® SPACER CLAMP• Ensures correct support for FLEXIBAR® in parallel,

without damage to the insulation.• Ensures correct space for optimum cooling.• Guarantees the performance of FLEXIBAR®

RFSREINFORCED FLEXIBAR® SUPPORT• Allows fixing of up to 8 FLEXIBAR® in parallel.• Easy fixing in the panel (25 mm pitch).• Exceptional resistance to short circuit forces.• Recommended distance between supports : 400 mm.

FS 24/32

FS 40/63FS 80/100

FS 24 553550 ≤ 24 mm 53 30 25 0,015 FS 32 553560 ≤ 32 mm 53 38 25 0,018 FS 40-63 553570 40-50 and 63 mm 95 150 10 0,100 FS 80-100 553580 80/100 mm 140 200 10 0,250

DESCRIPTION Part Type of H L

N° FLEXIBAR mm mm

UFS KITFS 24

FS 40-63

RFS

C

B

AH

D

M8

39

9 pcs

Ø9

40

210

RFS 40-63 553370 150 175 90 120 40➜ 63 1 0,240 RFS 80-100 553380 200 225 140 170 80➜ 100 1 0,300

DESCRIPTION Part A B C D FLEXIBAR N° mm mm mm mm H mm

PAGE 57TECH

NICA

L SE

CTIO

N

10

Powe

r fle

xibl

es

R

Manual tools

MCBB 559190 1 27


FLEXIDRILL RFLEXIDRILL R DRILL GUIDE• Multi-diameter, multi-distance between centres.

This guide facilitates the drilling of one or more holes of various diameters at different distances between centres.

• Length 250, width 300, height 150• Drill guide inserts for 6,5- 8,5-10,5-12,5 diameters.

FT KITFLEXIBAR® WORKBENCHEssential for the optimum use

of FLEXIBAR® • A complete set of useful hand tools for

FLEXIBAR®, easy to use, make cutting, stripping, bending, twisting, even simpler.

• Delivered with a clear illustrated instruction sheet.

MFB / MFTBENDING AND TWISTING TOOL• FLEXIBAR® BENDING TOOL

Saw guide includedL 170 x l 150 x H 220 mm

• FLEXIBAR® TWISTING TOOL To be used with the previous bending toolL 560 x l 270 x H 70 mm


FLEXIDRILL R 558600 1 9,5

MFCFLEXIBAR® SHEARING TOOL• Cuts quickly and accurately

without burrs or deformation• Cuts with the insulation on without any damage• Cost effective• Graduated endstop• Overall dimensions :

L 170 x H 270 x l 200 mm / Lever 460 mmWARNING : Cutting solid bar will damage the tool.

• Spare blade MFCB.

MFC 559170 1 3,5 MFCB 559120 1 0,5


BENDING TOOL MFB 559150 1 7 TWISTING TOOL MFT 559160 1 2,5


FT KIT 558900 1 35


MFSFLEXIBAR® STRIPPING TOOL • Cuts all 4 faces of the insulation in a single

operation, without marking the copper.Length 220 mm / Width 100 mm / Height 250 mm

MCBBMANUAL BENDING TOOLFOR SOLID COPPER BARS• Angle of bend = 120°• Copper (mm) = Maxi 120 x 10• L 300 x l 300 x H 260 mm

MFS 559100 1 8 SPARE BLADE SET MFS-B 559110 1 1 STRIPPING KNIFE SOK 559050 1 0,062 SOK SPARE BLADE SOK B 559060 1 0,002


100

FLEXIDRILL R

MFCMFS

FT KITMFB

MCBB

MFT

PAGE 15

BUSB

ARS

FLEX

IBAR

PAGE 9

11

Powe

r fle

xibl

es

R

Electro-hydraulic toolsto be used for FLEXIBAR ® or solid bars

FPTSELECTRO-HYDRAULIC PUMP• Strong lightweight construction• Working pressure : 700 bar - 10000 PSI• Supply voltage : 220V - 0,37 kW• Capacity : 0,3 l/mn to 700 bar• Punching capacity Ø 14 mm

10 mm thick, approx. 10 seconds• Dimensions : L 250 x l 250 x H 380 mm

HCHYDRAULIC ACTUATOR• Controls hydraulic tools n° 559450 and 559460

by simple positioning and 1/4 turn rotation• Max. supply pressure : 630 barsOVERALL DIMENSIONS :Diameter : 80 mm / Height : 175 mm

FPTBPUNCHING HEAD• Delivers 300 KN at 700 bar• Important : special die-sets

must be used for copper.• Stops included• Can punch solid bars up to 10 mm• Dimensions : L 300 x W 260 x H 400 mm

HYDRAULIC HOSELength 1,80 m ; with 2 quick release couplings

FPTS 560020 1 18,5


HC 559510 1 3,3


FPTB 560010 1 30


HCBBHYDRAULIC TOOL FOR BENDING SOLID BARS

• Max. capacity :

• Delivered without actuatorOVERALL DIMENSIONSLength : 210 mm / Width : 210 mm / Height : 150 mm

HCBB 559450 1 9,4


HCBCHYDRAULIC TOOL FOR SHEARING SOLID BARS

• Max. capacity :

• Adjustable stop• Clean neat and perpendicular cuts• Delivered without actuatorOVERALL DIMENSIONSLength : 185 mm / Width : 180 mm / Height : 210 mm

FPT KITCOMPLETE KITConsists of a hydraulic pump, punching head, flexi-ble hose, 5 diesets and 2 ejection stops.

HCBC 559460 1 9,1


FPT kit 560000 1 52


FPTF 560030 1 2

FPTT 560040 1 1

HFSTHYDRAULIC SHEARING TOOL• Cuts quickly and accurately without burrs

or deformation• Overall dimensions : L 185 x l 180 x H 210 mmTo be used with electro-hydraulic Part N° 560020WARNING : cutting solid bar will damage the tool.• Shearing tool guide HFST-B. Spare blade HFST-C.• Shearing tool ruler HFST-R.

HFST 559010 1 35 HFST-B 559020 1 1 HFST-C 559040 1 1 HFST-R 558990 1 10


SET OF 5 DIE SETS AND 2 EJECTION STOPS• Ø 6,5 mm + Ø 8,5 mm with ejection stop• Ø 11 mm + Ø 12,5 mm + Ø 14 mm with ejection stop

DIE SETS

EJECTION STOPS

FPTP 6,5 560060 6,5 1 0,9FPTP 8,5 560070 8,5 1 0,9FPTP 11 560090 11 1 0,9FPTP 12,5 560100 12,5 1 0,9FPTP 14 560110 14 1 0,9

DESCRIPTION Part Ø N° mm

FPTE 8,5 560120 6,5 and 8,5 1 0,09FPTE 14 560130 11 - 12,5 - 14 1 0,09

DESCRIPTION Part For Ø N° mm

FTPS

HC

HCBB

HFST FPTB

HCBC

HFST-B

HFST-R

PAGE 15

BUSB

ARS

FLEX

IBAR

PAGE 9

12

Powe

r fle

xibl

es

R

Documents

Power flexibles - Elec.ru