Upload
av00115240
View
258
Download
2
Embed Size (px)
Citation preview
8/14/2019 Power Electronics- Chapter 2
1/15
DRIVE AND SNUBBERDRIVE AND SNUBBERCIRCUITSCIRCUITS
Mohd Shawal Bin JadinMohd Shawal Bin Jadin
Ext : 2321Ext : 2321
BEE4223BEE4223
Power Electronics & Drives SystemsPower Electronics & Drives Systems
8/14/2019 Power Electronics- Chapter 2
2/15
LEARNING OUTCOMESLEARNING OUTCOMES
At the end of the lecture, studentshould be able to:
Identify the driver circuit for
electronics switches
Outline the importance of snubber
circuit in such that to smoothened thesmoothened theswitching transitionswitching transition
8/14/2019 Power Electronics- Chapter 2
3/15
DRIVER CIRCUIT (BASE / GATE)DRIVER CIRCUIT (BASE / GATE)
InterfaceInterface between control (low power electronics) and (highbetween control (low power electronics) and (high
power) switchpower) switch.
Functions:
amplifies control signal to a level required to drive poweramplifies control signal to a level required to drive powerswitchswitch
provides electrical isolation between power switch andprovides electrical isolation between power switch andlogic levellogic level
Complexity of driver varies markedly among switches.MOSFET/IGBT driversMOSFET/IGBT drivers are simplesimple but GTO driversGTO drivers are very
8/14/2019 Power Electronics- Chapter 2
4/15
8/14/2019 Power Electronics- Chapter 2
5/15
ELECTRICAL ISOLATION FOR DRIVERSELECTRICAL ISOLATION FOR DRIVERS
Power semiconductor devices can becategorized into 3 types based on theircontrol input requirements:
a) Current-driven devices BJTs, MDs, GTOs
b) Voltage-driven devices MOSFETs, IGBTs,MCTs
c) Pulse-driven devices SCRs, TRIACs
8/14/2019 Power Electronics- Chapter 2
6/15
CURRENT DRIVEN DEVICES (BJT)CURRENT DRIVEN DEVICES (BJT)
Power BJT devices have low current gain due toconstructional consideration, leading current than
would normally be expected for a given load orcollector current.The main problem with this circuit is the slow turn-
off time.
8/14/2019 Power Electronics- Chapter 2
7/15
CIRCUITSCIRCUITS
8/14/2019 Power Electronics- Chapter 2
8/15
::THYRISTORSTHYRISTORS
Pulse transformer is used for isolationused for isolation. R1is to limitlimitthe gate currentthe gate current
Normally a pulse with length 10us with amplitude of50mA is sufficient to turn-on the thyristors. It is quiteIt is quitecommon to fire the thyristors with successive pulsescommon to fire the thyristors with successive pulsesto ensure proper turn-onto ensure proper turn-on.
It is not possiblenot possible to tturn-offurn-offa thyristor with the abovecircuit
8/14/2019 Power Electronics- Chapter 2
9/15
EXAMPLE: SIMPLE MOSFET GATE DRIVEREXAMPLE: SIMPLE MOSFET GATE DRIVER
Note: MOSFET requires VMOSFET requires VGSGS =+15V for turn on=+15V for turn onand 0V to turn off.and 0V to turn off. LM311 is a simple amp withopen collector output Q1.
When BB11 is highis high, Q1 conducts. VGS is pulled to
ground. MOSFET is offMOSFET is off.
When BB11 is lowis low, Q1 will be off. VGS is pulled toVGG. If VIf VGGGG is set to +15V, the MOSFET turns on.is set to +15V, the MOSFET turns on.
8/14/2019 Power Electronics- Chapter 2
10/15
EXAMPLE: SIMPLE JFETEXAMPLE: SIMPLE JFET
GATE DRIVERGATE DRIVER
Example of having a chopper circuit that requiresswitching to control output voltage
8/14/2019 Power Electronics- Chapter 2
11/15
EXAMPLE: SIMPLE JFET GATE DRIVEREXAMPLE: SIMPLE JFET GATE DRIVER
Left side of the driver circuit is part where to control switching output. R2, C1 to control on time
R3 to control off-time
R5 to control pulse length (switching frequency)
D1 to make sure ON/OFF independently
RR22, C, C11 + R+ R55RR33, C, C11 + R+ R55
8/14/2019 Power Electronics- Chapter 2
12/15
SNUBBERSSNUBBERS
PCB construction, wire loops creates stray inductance,wire loops creates stray inductance, LLss..
Using KVL,Using KVL,
8/14/2019 Power Electronics- Chapter 2
13/15
SNUBBERSSNUBBERS
From previous equation, the voltage across the switch isthe voltage across the switch isbigger than the supply (for a short moment).bigger than the supply (for a short moment).
The spike may exceed the switch rated blocking voltagespike may exceed the switch rated blocking voltageand causes damageand causes damage due to overvoltage.
To preventTo prevent such occurrence, a snubber is put across thea snubber is put across the
switchswitch. An example of a snubber is an RCD circuit shownbelow.
Snubber circuit smoothened the transition and makeSnubber circuit smoothened the transition and makethe switch voltage rise more slowly.the switch voltage rise more slowly. In effect itdampens the high voltage spike to a safe value.
Switches and diodes requires snubbersSwitches and diodes requires snubbers. However, newgeneration of IGBT, MOSFET and GCT do not require it.
RCD SNUBBERSRCD SNUBBERS
8/14/2019 Power Electronics- Chapter 2
14/15
RCD SNUBBERSRCD SNUBBERS
In general, snubbers are used for:
turn-on:turn-on: to minimize large overcurrents through the device atto minimize large overcurrents through the device atturn-onturn-on
turn-off:turn-off:to minimize large overvoltages across the device duringto minimize large overvoltages across the device duringturn-turn-
off.off.
Stress reductionStress reduction: to shape the device switching waveformto shape the device switching waveformsuch that the voltage and current associated with the device aresuch that the voltage and current associated with the device are
??????????????
8/14/2019 Power Electronics- Chapter 2
15/15
??????????????
??????????????
??????????????????