Pmq Installation Guide

IBM Predictive Maintenance and QualityVersion 1.0

Installation Guide

NoteBefore using this information and the product it supports, read the information in Notices on page 59.

Product InformationThis document applies to IBM Predictive Maintenance and Quality 1.0 and may also apply to subsequent releases.

Licensed Materials - Property of IBM

Copyright IBM Corporation 2013.US Government Users Restricted Rights Use, duplication or disclosure restricted by GSA ADP Schedule Contractwith IBM Corp.

ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Chapter 1. IBM Predictive Maintenance and Quality . . . . . . . . . . . . . . . . . 1Solution architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 2. Installation planning and preparation . . . . . . . . . . . . . . . . . . 5Supported operating systems and hardware requirements . . . . . . . . . . . . . . . . . . . . 5

Ensuring that the required operating system packages are installed . . . . . . . . . . . . . . . . 6Verifying that the Legacy UNIX compatibility package is installed . . . . . . . . . . . . . . . . 7Installing prerequisite operating system packages on the BI node computer . . . . . . . . . . . . . 8

Installation of Perl on the MDM node computer . . . . . . . . . . . . . . . . . . . . . . . 8Installing IBM Data Server Driver on the ESB node computer . . . . . . . . . . . . . . . . . . . 9Disabling SELinux on all target computers . . . . . . . . . . . . . . . . . . . . . . . . . 9Computer firewall settings required for the installation . . . . . . . . . . . . . . . . . . . . . 9

Configuring your firewall settings for the Deployment Wizard . . . . . . . . . . . . . . . . . 10Configuring your firewall settings for the Data node installation and configuration . . . . . . . . . . 10Disabling your computer's firewall during the installation . . . . . . . . . . . . . . . . . . . 11

Mounting the USB hard disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Verifying that your servers prerequisites are met . . . . . . . . . . . . . . . . . . . . . . . 11

Chapter 3. Installation of the server components . . . . . . . . . . . . . . . . . 13Installation process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Starting the installer for the server components . . . . . . . . . . . . . . . . . . . . . . . 14Setting port numbers for the Deployment Wizard to use . . . . . . . . . . . . . . . . . . . . 14Installing or selecting a database instance . . . . . . . . . . . . . . . . . . . . . . . . . 15Specifying the target computers to install the server components . . . . . . . . . . . . . . . . . 15Configuring parameters for the server components installation . . . . . . . . . . . . . . . . . . 16Starting the installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Configure the server components and test the installation . . . . . . . . . . . . . . . . . . . . 22

Testing the database installation and configuration . . . . . . . . . . . . . . . . . . . . . 22Configuring WebSphere Application Server for IBM Cognos BI . . . . . . . . . . . . . . . . . 23Saving your IBM Cognos Configuration settings and starting the services . . . . . . . . . . . . . 24Setting the password for the mqm user on the ESB node computer . . . . . . . . . . . . . . . . 24Testing the installation of the server components . . . . . . . . . . . . . . . . . . . . . . 25

Computer firewall settings to run the server components . . . . . . . . . . . . . . . . . . . . 25Configuring your firewall settings for all nodes . . . . . . . . . . . . . . . . . . . . . . 25Configuring your firewall settings for the Analytics node computer . . . . . . . . . . . . . . . 26Configuring your firewall settings for the BI node computer . . . . . . . . . . . . . . . . . . 27Configuring your firewall settings for the ESB node computer . . . . . . . . . . . . . . . . . 28Configuring your firewall settings for the MDM node computer. . . . . . . . . . . . . . . . . 28Configuring your firewall settings for the Data node computer . . . . . . . . . . . . . . . . . 29

Chapter 4. Installation of the server artifacts . . . . . . . . . . . . . . . . . . . 31Starting the installer for the server artifacts . . . . . . . . . . . . . . . . . . . . . . . . . 31Setting port numbers for the Deployment Wizard to use . . . . . . . . . . . . . . . . . . . . 31Specifying the target computers on which you will install the server artifacts . . . . . . . . . . . . . 32Configuring parameters for the server artifacts installation . . . . . . . . . . . . . . . . . . . 33Starting the installation of the server artifacts . . . . . . . . . . . . . . . . . . . . . . . . 36Complete the configuration of the server components . . . . . . . . . . . . . . . . . . . . . 36

Verifying the configuration of IBM SPSS Collaboration and Deployment Services . . . . . . . . . . . 36Configuring the MDM node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Chapter 5. Installation of the client components . . . . . . . . . . . . . . . . . . 39Client components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Copyright IBM Corp. 2013 iii

Starting the installer for the client components . . . . . . . . . . . . . . . . . . . . . . . 40Installing IBM SPSS Collaboration and Deployment Services Deployment Manager . . . . . . . . . . . 40

Adding a content server connection for IBM SPSS Collaboration and Deployment Services . . . . . . . . 41Adding users and groups to IBM SPSS Collaboration and Deployment Services . . . . . . . . . . . 41Importing the Predictive Maintenance and Quality resource definitions into IBM SPSS Collaboration andDeployment Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Adding credential definitions to IBM SPSS Collaboration and Deployment Services . . . . . . . . . . 43Adding server definitions to IBM SPSS Collaboration and Deployment Services . . . . . . . . . . . 44Creating scoring configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Chapter 6. Uninstallation of the IBM Predictive Maintenance and Quality components 47Uninstalling components from the Predictive Analytics node computer . . . . . . . . . . . . . . . 47Uninstalling components from the BI node computer . . . . . . . . . . . . . . . . . . . . . 47Uninstalling components from the ESB node computer . . . . . . . . . . . . . . . . . . . . . 48Uninstalling components from the MDM node computer . . . . . . . . . . . . . . . . . . . . 48Uninstalling components from the Data node computer . . . . . . . . . . . . . . . . . . . . 49

Appendix A. Samples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Loading the sample data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Removing sample data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Appendix B. Products installed with IBM Predictive Maintenance and Quality . . . . . 53

Appendix C. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 55Log in as root rather than su or sudo . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Browser not supported for the Launchpad . . . . . . . . . . . . . . . . . . . . . . . . . 55Installer does not launch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Test Connections validation errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Viewing log files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Temporary file locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Ensuring connectivity between the Analytics node and the Data node computers . . . . . . . . . . . . 56Modeler Server type not displaying in resource definitions . . . . . . . . . . . . . . . . . . . 56Unable to import the company archive in MDM . . . . . . . . . . . . . . . . . . . . . . . 56Error installing IBM Cognos BI in IBM Predictive Maintenance and Quality . . . . . . . . . . . . . . 57Administration tool and product portal reference . . . . . . . . . . . . . . . . . . . . . . . 57

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

iv IBM Predictive Maintenance and Quality Version 1.0: Installation Guide

IntroductionIBM Predictive Maintenance and Quality uses data from multiple sources to giveyou the information that you need to make informed operational, maintenance,repair, or component replacement decisions.

IBM Predictive Maintenance and Quality provides you with operationalintelligence data, which enables you to:v Understand, monitor, predict, and control product and process variabilityv Perform in-depth root cause failure analysisv Identify incorrect operating practicesv Enhance equipment and process diagnostics capabilities

It also provides you with asset performance management capabilities that enableyou to:v Have forward visibility into equipment and process performancev Increase asset uptimev Identify safety issuesv Identify improper maintenance proceduresv Optimize maintenance intervals and procedures.

Audience

This document is intended to help users install Predictive Maintenance andQuality.

Finding information

To find IBM Predictive Maintenance and Quality product documentation on theweb, go to the IBM Predictive Maintenance and Quality information center(http://pic.dhe.ibm.com/infocenter/pmq/v1r0m0/index.jsp).

Accessibility features

Accessibility features help users who have a physical disability, such as restrictedmobility or limited vision, to use information technology products. Some of thecomponents included in the IBM Predictive Maintenance and Quality solution haveaccessibility features.

IBM Predictive Maintenance and Quality HTML documentation has accessibilityfeatures. PDF documents are supplemental and, as such, include no addedaccessibility features.

Forward-looking statements

This documentation describes the current functionality of the product. Referencesto items that are not currently available may be included. No implication of anyfuture availability should be inferred. Any such references are not a commitment,promise, or legal obligation to deliver any material, code, or functionality. Thedevelopment, release, and timing of features or functionality remain at the solediscretion of IBM.

Copyright IBM Corp. 2013 v

vi IBM Predictive Maintenance and Quality Version 1.0: Installation Guide

Chapter 1. IBM Predictive Maintenance and QualityWith IBM Predictive Maintenance and Quality, you can monitor, analyze, andreport on information that is gathered from devices. In addition, recommendationsfor actions can be generated by IBM Predictive Maintenance and Quality.

IBM Predictive Maintenance and Quality is an integrated solution that you can useto perform the following tasks:v Predict the failure of an instrumented asset so that you can prevent costlyunexpected downtime.

v Quickly mine maintenance logs to determine the most effective repairprocedures and maintenance cycles.

v Identify the root cause of asset failure faster so that you can take correctiveactions.

Instrumented assets generate data such as device ID, timestamp, temperature, andstatus code. This data can be collected and used in models that predict when anasset is likely to fail.

Examples of instrumented assets are manufacturing equipment, mining equipment,drilling equipment, farming equipment, security equipment, cars, trucks, trains,helicopters, engines, cranes, oil platforms, and wind turbines.

For example, an oil refinery is a system that combines thousands of interlockingpieces. It is critical that such a system is able to work safely and efficiently. Youcan use IBM Predictive Maintenance and Quality to monitor and track the lifecycleof each piece of the refinery, such as each pipe, pump, compressor, valve, furnace,turbine, tank, heat exchange unit, and boiler. Reports give you the information toensure that you have the right parts available and can schedule repairs duringdowntimes.

Predictive maintenance

In predictive maintenance, you look for patterns in the usage and environmentalinformation for equipment that correlate with failures that take place. Thisinformation is used to create predictive models to score incoming new data. Youcan predict the likelihood of failure. Scores are generated from this informationthat give you an indication of the health of the piece of equipment. In addition,key performance indicators (KPIs) are collected, which are used for reporting. KPIshelp you to identify assets that do not conform to normal patterns of behavior. Youcan define rules to generate recommendations when a piece of equipment isidentified as having a high probability of failure. Recommendations can be fed intoother systems so that people are alerted to them automatically.

Predictive quality in manufacturing

Past operations data, environmental data, and historical defect data can be used toidentify the causes of elevated defect rates. This information is used in predictivemodels, so that when incoming data is fed into the models, you can predict thelikely defect rates. The predicted values are then used for analysis and reportingand to drive recommendations such as modification to inspection patterns, orrecalibration of machinery. Scoring can be done on a near real-time basis.

Copyright IBM Corp. 2013 1

Solution architectureThe IBM Predictive Maintenance and Quality solution is divided into nodes, whereeach node provides a specific function for the solution. Each node must beinstalled on a separate computer or on a separate virtual machine image fromother nodes.

For a complete list of products included with Predictive Maintenance and Quality,see Appendix B, Products installed with IBM Predictive Maintenance andQuality, on page 53.

The following diagram shows the nodes.

Predictive Analytics node

The Analytics node in provides predictive scores and offers recommendations.

This node has the following software installed:v IBM WebSphere Network Deploymentv IBM SPSS Collaboration and Deployment Servicesv IBM SPSS Modeler Serverv IBM SPSS Data Access Packv IBM SPSS Text Analytics Serverv IBM SPSS Modeler Collaboration and Deployment Services Adapterv IBM SPSS Decision Managementv IBM SPSS Statistics Serverv IBM SPSS Statistics Collaboration and Deployment Services Adapter

Figure 1. Predictive Maintenance and Quality nodes

2 IBM Predictive Maintenance and Quality Version 1.0: Installation Guide

v IBM DB2 Client

Business Intelligence (BI) nodeThe BI node provides dashboards and reports.

This node has the following software installed:v IBM WebSphere Network Deploymentv IBM HTTP Serverv IBM Cognos Business Intelligencev IBM DB2 Client

Enterprise Service Bus (ESB) nodeThe ESB node server processes events, updates the content for IBM CognosBusiness Intelligence, and triggers predictive scoring and decision management. Italso loads master data into the solution.

This node has the following software installed:v IBM WebSphere Message Queuev IBM WebSphere Message Brokerv IBM WebSphere Message Broker Explorerv IBM WebSphere Message Broker ODBC Database Extender

Master Data Management (MDM) nodeThe MDM node manages the master data for the solution. The master dataincludes the set of devices that supply events to the solution and their locations. Italso includes metadata that is used to determine how events are processed by thesolution.

This node has the following software installed:v IBM WebSphere Network Deploymentv IBM InfoSphere Master Data Management Collaboration Editionv IBM DB2 Client

Data node

The Data node provides the database server that contains the databases that areused by other products in the solution. The database acts as an event store andholds calculated key performance indicators (KPIs) and profiles. It also containssupporting master data for the solution.

This node has the following software installed:v IBM DB2 Enterprise Server Edition

Chapter 1. IBM Predictive Maintenance and Quality 3

Chapter 2. Installation planning and preparationBefore you install IBM Predictive Maintenance and Quality, ensure that thecomputers that you use meet the minimum requirements for operating systems,prerequisite software, processing, and disk space.

You must also install additional prerequisite software on some computers,including the Business Intelligence (BI) node, the Master Data Management (MDM)node, and the Enterprise Service Bus (ESB) node computers.

Important: The computers or virtual machines that you use for PredictiveMaintenance and Quality nodes must not have any of the included softwarealready installed.

Critical installation and configuration issues

To review a list of critical installation and configuration issues for IBM PredictiveMaintenance and Quality version 1.0 as of the date of release, see the documenttitled Critical installation and configuration issues for IBM Predictive Maintenanceand Quality version 1.0 (http://www.ibm.com/support/docview.wss?uid=swg21637185).

Supported operating systems and hardware requirementsReview the minimum hardware and operating system requirements before youinstall IBM Predictive Maintenance and Quality. The requirements apply for allcomputers or virtual machines that you use for the installation.

Server computers

The IBM Predictive Maintenance and Quality server components must be installedon computers that are running the 64-bit Red Hat Enterprise Linux Server Editionversion 6.3 (x86_64) operating system.

You must have the Legacy UNIX compatibility package installed. The package isselected when the operating system is set up. The components of this packagemust be installed on each computer or virtual machine image on which you installa Predictive Maintenance and Quality node.

Hardware requirements

At a minimum, each computer or virtual machine that is hosting aPredictive Maintenance and Quality server component, or node, must havethe following hardware requirements:v 4 processorsv 8 GB of RAMv 500 GB of hard disk spaceEach node must be installed on a separate computer or on a separatevirtual machine image.

User requirements


You must have root access to all of the computers on which you install aPredictive Maintenance and Quality node. Each computer on which youinstall a node must have remote root log in enabled.

You must log in to the computer where you run the installer as root.

Client computers

The Predictive Maintenance and Quality client components must be installed oncomputers that are running Microsoft Windows 7 64-bit operating systems.

Ensuring that the required operating system packages areinstalled

Specific operating system packages must be installed on each computer or virtualmachine where you install an IBM Predictive Maintenance and Quality node.

Ensure that the following packages are installed:v libXext-1.1-3.el6.i686.rpmv libXft-2.1.13-4.1.el6.i686.rpmv libXi-1.3-3.el6.i686.rpmv libXp-1.0.0-15.1.el6.i686.rpmv libXpm-3.5.8-2.el6.i686.rpmv libXrender-0.9.5-1.el6.i686.rpmv libXtst-1.0.99.2-3.el6.i686.rpmv compat-libstdc++-33-3.2.3-69.el6.i686.rpmv compat-libstdc++-296-2.96-144.el6.i686.rpmv expat-2.0.1-11.el6_2.i686.rpmv fontconfig-2.8.0-3.el6.i686.rpmv freetype-2.3.11-6.el6_2.9.i686.rpmv libstdc++-4.4.6-4.el6.i686.rpmv libX11-1.3-2.el6.i686.rpmv libXau-1.0.5-1.el6.i686.rpmv libxcb-1.5-1.el6.i686.rpmv libICE-1.0.6-1.el6.i686.rpmv libuuid-2.17.2-12.7.el6.i686.rpmv libSM-1.1.0-7.1.el6.i686.rpmv libXt-1.0.7-1.el6.i686.rpmv libXmu-1.0.5-1.el6.i686.rpmv libjpeg-6b-46.el6.i686.rpmv libpng-1.2.49-1.el6_2.i686.rpmv zlib-1.2.3-27.el6.i686.rpmv glibc-2.12-1.80.el6.i686.rpmv openmotif-2.3.3-4.el6.i686.rpm

Procedure1. Log in as root.2. Type the following command to verify that an operating system package is

installed:


rpm -qi full_package_name

For example, to verify that libXext-1.1-3.el6.i686 is installed, type rpm -qilibXext-1.1-3.el6.i686.

3. Install any package that is not already installed.You must download any missing package, and then install the downloadedpackage by typing the following command:rpm -ihv full_package_name.rpm

For example, to install libXext-1.1-3.el6.i686, type rpm -ihvlibXext-1.1-3.el6.i686.rpm.

4. Repeat these steps on each computer on which you install a PredictiveMaintenance and Quality node.

Verifying that the Legacy UNIX compatibility package isinstalled

Legacy UNIX compatibility must be installed on each computer or virtual machinewhere you install an IBM Predictive Maintenance and Quality node.

You must verify that the following packages are installed:v authd-1.4.3-30.el6.x86_64.rpmv cups-lpd-1.4.2-48.el6.x86_64.rpmv dump-0.4-0.6.b42.el6.x86_64.rpmv finger-0.17-39.el6.x86_64.rpmv finger-server-0.17-39.el6.x86_64.rpmv krb5-appl-servers-1.0.1-7.el6_2.1.x86_64.rpmv ksh-20100621-16.el6.x86_64.rpmv mksh-39-7.el6.x86_64.rpmv ncompress-4.2.4-54.el6_2.1.x86_64.rpmv rsh-0.17-60.el6.x86_64.rpmv rsh-server-0.17-60.el6.x86_64.rpmv rusers-0.17-61.el6.x86_64.rpmv rusers-server-0.17-61.el6.x86_64.rpmv rwho-0.17-34.el6.x86_64.rpmv talk-0.17-34.el6.x86_64.rpmv talk-server-0.17-34.el6.x86_64.rpmv tcp_wrappers-7.6-57.el6.x86_64.rpmv telnet-0.17-47.el6.x86_64.rpmv telnet-server-0.17-47.el6.x86_64.rpmv tftp-0.49-7.el6.x86_64.rpmv xinetd-2.3.14-34.el6.x86_64.rpm

Procedure1. Log in as root.2. Type the following command to verify that an operating system package is

installed:rpm -qi full_package_name

For example, to verify that authd-1.4.3-30.el6.x86_64 is installed, type rpm-qi authd-1.4.3-30.el6.x86_64.

Chapter 2. Installation planning and preparation 7


For example, to install authd-1.4.3-30.el6.x86_64, type rpm -ihvauthd-1.4.3-30.el6.x86_64.rpm.

4. Repeat these steps on each computer on which you install a PredictiveMaintenance and Quality node.

Installing prerequisite operating system packages on the BInode computer

Specific operating system packages must be installed on the Business Intelligence(BI) node computer or virtual machine before you install IBM PredictiveMaintenance and Quality.

The following packages must be installed:v libselinux-2.0.94-5.3.el6.i686.rpmv cracklib-2.8.16-4.el6.i686.rpmv db4-4.7.25-17.el6.i686.rpmv audit-libs-2.2-2.el6.i686.rpmv pam-1.1.1-13.el6.i686.rpm

Procedure1. Log in to the BI node computer as root.2. Type the following command to verify that an operating system package is

installed:rpm -qi full_package_name

For example, to verify that libselinux-2.0.94-5.3.el6.i686 is installed, typerpm -qi libselinux-2.0.94-5.3.el6.i686.


For example, to install libselinux-2.0.94-5.3.el6.i686, type rpm -ihvlibselinux-2.0.94-5.3.el6.i686.rpm.

Important: To install pam-1.1.1-13.el6.i686.rpm, use the following command:rpm --force -ivh pam-1.1.1-13.el6.i686.rpm.

Installation of Perl on the MDM node computerYou must install a version of Perl on the Master Data Management (MDM) nodecomputer for IBM Predictive Maintenance and Quality.

In the Deployment Wizard, you are prompted for a location on the MDM nodecomputer where you installed Perl.

For more information about installing Perl for IBM InfoSphere Master DataManagement, see the MDM documentation(pic.dhe.ibm.com/infocenter/mdm/v10r1/index.jsp?topic=%2Fcom.ibm.pim.ins.doc%2Fpim_tsk_installingperl.html).


Note: For IBM Predictive Maintenance and Quality, the minimum version of Perlis 5.10.

Installing IBM Data Server Driver on the ESB node computerBefore you can deploy IBM Predictive Maintenance and Quality, you must installthe IBM Data Server Driver for ODBC and CLI on the Enterprise Service Bus (ESB)node computer.

Procedure1. Go to the IBM driver and client download page (www.ibm.com/support/

docview.wss?uid=swg21385217).2. Click the link for IBM Data Server Driver for ODBC and CLI (CLI Driver).3. If prompted, log in with your IBM account.4. Select IBM Data Server Driver for ODBC and CLI (Linux AMD64 and Intel

EM64T).5. Click Continue, and download the driver.6. Go to the directory where you downloaded the driver.7. Type the following command to extract the files:

tar -zxf ibm_data_server_driver_for_odbc_cli_linuxx64_v10.1.tar.gz

The files are extracted to the odbc_cli/clidriver directory.8. Copy the odbc_cli directory to the var directory to match the default location

in the server installer. For example, ensure the path is /var/odbc_cli.

Disabling SELinux on all target computersYou must disable the Security-Enhanced Linux (SELinux) feature on all computerswhere you install an IBM Predictive Maintenance and Quality node.

Procedure1. Log in as root.2. Go to the /etc/sysconfig directory.3. Type sestatus to verify that the SELinux feature is disabled.4. If the SELinux feature is not disabled, open the selinux file for editing.5. Change the SELINUX value to disabled.

For example, the file should include:SELINUX=disabled

6. Save and close the file.7. Restart the computer for the changes to take effect.8. Repeat these steps on each computer on which you install a Predictive

Maintenance and Quality node.

Computer firewall settings required for the installationThe Deployment Wizard requires bidirectional communication with each IBMPredictive Maintenance and Quality node when you install a server component orserver artifact component, and your firewall can interfere with this communication.To unsure this communication, you must configure your firewall settings for theinstallation.


Configuring your firewall settings for the Deployment WizardOn each computer on which you will install an IBM Predictive Maintenance andQuality node, you must open two ports to allow the bidirectional communicationthat is required by the Deployment Wizard. After you open the ports in yourfirewall, you can then enter these port values in the Deployment Wizard.

Procedure1. Log in as root.2. Back up your existing firewall settings by typing the following command:

/etc/init.d/iptables save

3. Add rules for the two ports that are required by the Deployment Wizard withthe following command:iptables -I INPUT -m state --state NEW -m tcp -p tcp --dport 35000 -j ACCEPTiptables -I INPUT -m state --state NEW -m tcp -p tcp --dport 30000 -j ACCEPT

Where port 35000 and 30000 are available port numbers on your computers.You do not have to use these port numbers, but you must use available portnumbers.If you do not use ports 35000 and 30000, ensure that you change only the portnumber values in the commands.

Tip: Using the same port numbers for each target computer is recommended.4. Type the following command to save your firewall settings:


5. Type the following command to restart your firewall./etc/init.d/iptables restart

6. Verify that your changes have been applied with the following command:iptables -L

The added port should appear in the list.7. Repeat these steps on each computer on which you install a Predictive

Maintenance and Quality node, and on the computer from where you run theinstallation if it is not one of the node computers.

Configuring your firewall settings for the Data nodeinstallation and configuration

Before you can install and configure the IBM Predictive Maintenance and QualityData node, you must ensure that the database server port number is open on theData node computer.

Procedure1. Log in to the Data node computer as root.2. Back up your existing firewall settings by typing the following command:


3. Add rules for the port with the following command:iptables -I INPUT -m state --state NEW -m tcp -p tcp --dport port_number -j ACCEPT

For example, to open 50000, type the following commandiptables -I INPUT -m state --state NEW -m tcp -p tcp --dport 50000 -j ACCEPT

Note: If you are using a port number other than 50000 for your databaseserver, ensure you open the appropriate port number.


4. Type the following command to save your firewall settings:/etc/init.d/iptables save



The added ports should appear in the list.

Disabling your computer's firewall during the installationIf you choose to temporarily disable your computer's firewall during theinstallation of IBM Predictive Maintenance and Quality, ensure that you enable thefirewall on each node after the installation is complete.

Important: If you disable your computer's firewall during the installation, youmust still ensure that the required ports are opened on each node computer whenyou restart your firewall.

Procedure1. Log in as the root user.2. Go to the /etc/init.d directory.3. Type the following command:

iptables stop

4. Repeat these steps on each computer on which you install a node and on theserver from which you are running the installation.

What to do next

After the installation is complete, on each node, go to the /etc/init.d directory,and type iptables start to restart your firewall.

Mounting the USB hard disk driveThe installation files for IBM Predictive Maintenance and Quality are provided ona universal serial bus (USB) hard disk drive. You can run the installation from theUSB or you can copy the files to your computer before you start the installation.Before you do either, you must mount the USB hard disk drive.

For more information about mounting USB hard disk drives, see the Red HatCustomer Portal (https://access.redhat.com/home).

Verifying that your servers prerequisites are metScripts are provided to help you ensure that the computers on which you install anIBM Predictive Maintenance and Quality node meet the minimum requirements.

The following scripts are provided:

CheckPkg.shVerifies that the required rpm packages are installed on the computer. Therpm names are listed in the packages.lst file.

CheckDB2.shVerifies the version, installation location, instance name, and status of anexisting IBM DB2 server.


CheckPaf.shVerifies the operating system, disk space, memory, and number ofprocessors for computer.

checkport.shVerifies that a port is open on the computer firewall. For example, on theData node computer, type ./checkport.sh 50000 to ensure that port 50000is open on that computer.

CheckRemotePort.shVerifies that a port is open on a remote computer's firewall. For example,to verify that the database server port number is open on the Data nodecomputer, type ./CheckRemotePort.sh data_node_name 50000 to ensure thatport 50000 is open on that computer. data_node_name can be the fullyqualified domain name or IP address of the Data node computer.

CheckUser.shVerifies that the current user is root.

CheckWAS.shTests if WebSphere Application Server is installed on a node computer. Ifinstalled, the version, build level and date, and installation location aredisplayed.

Procedure1. In a terminal window, go to the USB hard disk drive that you mounted or to

the directory where you copied the installation files.2. In a terminal window, go to the USB hard disk drive that you mounted or to

the directory where you copied the installation files.3. Go to the Prerequisite Checker directory.4. Copy the scripts to each computer on which you want to verify that the

prerequisites are met.5. Run the scripts as required.


Chapter 3. Installation of the server componentsThe installation program installs the required software on each computer that youidentify as an IBM Predictive Maintenance and Quality node. The installationprogram can be run from one of the computers that will be a node, or it can berun from another computer.

Installation processWith the IBM Predictive Maintenance and Quality installation program, you canselect the individual computers on which each solution node is to be installed andenter configuration information for each software component.

In the diagram, the staging server represents the computer from which you run theinstallation. In your installation, the staging server can also be used as a node

Figure 2. Predictive Maintenance and Quality installation process


computer. The staging server must also be using the same operating system as theother computers on which you install a node. It must also have the sameprerequisites.

Starting the installer for the server componentsUse the Launchpad to start the IBM Predictive Maintenance and Quality serverinstaller.

Before you begin

Ensure that you are logged in as root.

You must have a Firefox, version 10 or earlier, or SeaMonkey, version 2.9 or earlier,web browser installed and set as your default web browser on the computer fromwhere you run the installation.


the directory where you copied the installation files.2. Go to the ServerInstaller/disk1 directory.3. Type the following command to change the permissions for the installation

files:chmod -R 755 *

4. Enter the following command:./launchpad.sh

5. Review the information in the Launchpad panels.6. To start the Deployment Wizard, click Install Server > Predictive Maintenance

and Quality Server Installer.

Setting port numbers for the Deployment Wizard to useIf you opened ports for the installation of IBM Predictive Maintenance and Qualitycomponents, you must set those port numbers in the Deployment Wizard.

Procedure1. In the Deployment Wizard, click Edit > Preferences.

The Deployment Preferences window appears.2. Enter 30000 in the Data Port Number box.

Important: Ensure that you enter the port number that you opened if youselected a port other than 30000.

3. Enter 35000 in the Communication Port Number box.


4. If you are using the computer on which you are running the installation as anode, do the following steps:a. Click Target Computer Settings.b. Select localhost in the Target Computer field.c. Enter the communication port number that you set in the Communication

Port field. For example, enter 35000.


Note: The RMI Registry Port is unavailable if you are using localhost as anode.

Installing or selecting a database instanceIBM Predictive Maintenance and Quality requires a database instance. You caninstall IBM DB2 from the Deployment Wizard or use an existing IBM DB2instance.

If you are using an existing IBM DB2 instance, it must be IBM DB2 EnterpriseServer Edition 9.7 with IBM DB2 9.7 Fix Pack 7.

Procedure1. Select one of the following options:

v Install IBM DB2 Enterprise Server Editionv Use existing IBM DB2 Enterprise Server EditionIf you select this option, IBM DB2 Enterprise Server Edition must already beinstalled and running on the Data node computer.

2. Click Next.

Specifying the target computers to install the server componentsYou must specify a different target computer for each IBM Predictive Maintenanceand Quality node. A node can be installed on a computer or virtual machine, buteach node must be installed on a separate computer or virtual machine.

Before you begin

You must have root access on each computer on which you install a node.

You might have to change a setting in a configuration file on your target computerto allow the Deployment Wizard to access the computer as root. Use thefollowing steps if you receive a message that says the connection to the targetcomputer was refused:1. On the target computer, go to the /etc/ssh directory and open sshd_config for

editing.2. Change the PermitRootLogin property to yes.3. Save the file. You may have to restart the server for the change to take effect.

Procedure1. On the Specify Target Computers pages of the Deployment Wizard, enter the

name or IP address of the computer on which you install a node in the TargetComputer box.The Deployment Wizard prompts you for each node computer.If you are installing a node on the computer where you are running theDeployment Wizard, you can enter localhost.

2. Click Add.a. When you enter a computer other than localhost, in the Target Computer

Credentials box, enter the User ID and Password for the root user.

Important: Ensure that you enter the credentials for the root user on thetarget computer.

Chapter 3. Installation of the server components 15

b. Click Test Login.c. Click Add.

The computer that you entered appears in the Selected target computersbox.

3. Do the following steps if you opened ports for the installation.a. Click Edit > Preferences.b. Click Target Computer Settings.c. Select the computer name or IP address in the Target Computer field.d. Enter the communication port number that you set in the Communication

Port field. For example, enter 35000.e. Enter the Data Port Number that you set in the RMI Registry Port field.

For example, enter 30000.

Note: If you are using localhost as a node in the installation, the RMIRegistry Port is unavailable.

4. In the Selected target computers box, select the target computer, and click TestConnections.

Important: Test Connections tests the connection, tests the credentials, andlocates or enables a deployment agent on the target computer. You must havean active deployment agent on each target computer.If you receive an error message after you click Test Connections, you mighthave to change some settings on your computers.v Edit your iptable settings or temporarily disable your firewall. For moreinformation, see Computer firewall settings required for the installation onpage 9.

v Compare and correct your domain name system (DNS) settings for eachcomputer. For example, type sudo system-config-network. Select DNSconfiguration, and ensure that your host name domain and DNS search pathsettings are correct.

v Ensure that the /etc/host file has the correct entries.5. Click Next.6. Repeat the steps for each computer on which you install a node.

Configuring parameters for the server components installationThe Deployment Wizard displays some default values for each component of IBMPredictive Maintenance and Quality. You can accept the default values or changethem to suit your environment.

If you are prompted for users, the Deployment Wizard creates the users on theappropriate target node computer, if they do not exist. For example, IBM DB2requires a DB2 administrator user, an instance owner user, and a fenced user. Eachof these users is created on the Data node computer.

Procedure

Use the following tables to verify or enter values in each field on each panel of theDeployment Wizard:v Clicking Browse browses the target computer's file system. It does not browsethe local computer from where you are running the Deployment Wizard.


v For some values, such as passwords, default values are not provided. Ensurethat you enter all values on each panel of the Deployment Wizard.

v On the Configure IBM DB2 Enterprise Edition page, enter a name for eachdatabase that is to be created by the Deployment Wizard.

Important: Ensure you use a separate database for each product.

Important: You cannot use the same user for the IBM DB2 administrative userand the instance owner. They must be different users.

Table 1. IBM DB2 configuration parameters for a new database server installationField Default or example value Description

DB2 Server InstallationDirectory

/opt/ibm/db2/V9.7 The location where IBM DB2is to be installed on the Datanode computer.

DB2 Database Port Number 50000 The port number that is usedby IBM DB2.

DB2 Server AdministrativeUser Name

dasusr1 The user ID that runs theadministration server.

DB2 Server AdministrativePassword

There is no default value forthis field.

The password for the user IDthat runs the administrationserver.

DB2 Server AdministrativeHome Directory

/home/dasusr1 The home directory for theuser ID that runs theadministration server. Thisdirectory is on the Data nodecomputer's file system.

DB2 Instance Owner UserName

db2inst1 The user ID that controls theDB2 processes and owns thedirectories that are used bythe database instance.

DB2 Instance OwnerPassword


The password for the DB2instance owner user.

DB2 Instance Owner HomeDirectory

/home/db2inst1 The home directory for theDB2 instance owner user.This directory is on the Datanode computer's file system.

DB2 Fenced User Name db2fenc1 The user ID that can runuser-defined functions andstore procedures.

DB2 Fenced Password There is no default value forthis field.


DB2 Fenced User HomeDirectory

/home/db2fenc1 The home directory for theDB2 instance owner user.This directory is on the Datanode computer's file system.

Table 2. IBM DB2 configuration parameters for an existing database serverField Default or example value Description

DB2 Installation Location /opt/ibm/db2/V9.7 The location where IBM DB2is installed on the Data nodecomputer.


Table 2. IBM DB2 configuration parameters for an existing database server (continued)Field Default or example value Description

DB2 Instance Name db2inst1 The name of the instance inwhich your databases will becreated.

DB2 Instance Password There is no default value forthis field.


DB2 Port Number 50000 The port number that is usedby IBM DB2.

Table 3. IBM DB2 configuration parameters: Database names.Important: The database names cannot exceed 8 characters.Field Default or example value Description

SPSS Database Name SPSSDB The SPSS database that isused by the components thatare installed on thePredictive Analytics nodecomputer.

Cognos Database Name COG102CS The IBM Cognos contentstore database.

MDM Database Name MDMDB The Master DataManagement (MDM) nodedatabase.

Table 4. IBM DB2 client parameters.Note: The values entered are applied to all nodes where the IBM DB2 client is installed.Field Default or example value Description

DB2 Client InstallationDirectory

/opt/ibm/db2/V9.7 The location where the IBMDB2 client is to be installed.This directory is on theMDM node, BusinessIntelligence (BI) node, andAnalytics node computer'sfile system.

DB2 Client Instance UserName

db2inst1 The user ID for the DB2client.

DB2 Client InstancePassword


The password for the DB2client instance owner user.

DB2 Client Instance HomeDirectory

/home/db2inst1 The home directory for theDB2 client instance owneruser on each node.

Table 5. WebSphere installation parametersField Default or example value Description

WebSphere InstallationDirectory

/opt/IBM/WebSphere/AppServer

The location where theWebSphere ApplicationServer is to be installed. Thelocation is the same for eachnode where WebSphere isinstalled.


Table 6. HTTP Server installation parametersField Default or example value Description

HTTP Server InstallationDirectory

/opt/IBM/HTTPServer The location where IBMHTTP Server is to beinstalled. This directory is onthe BI node computer's filesystem.

HTTP Port Number 80 The port number that is usedby HTTP Server.

Table 7. IBM Cognos BI installation parametersField Default or example value Description

Cognos BI InstallationLocation

/opt/ibm/cognos/c10_64 The location where IBMCognos BI is to be installed.This directory is on the BInode computer's file system.

Table 8. WebSphere profile for IBM Cognos BI parameters.Note: The settings in this table are applied to the WebSphere installation on the BI node.Field Default or example value Description

WebSphere Profile Location /opt/IBM/WebSphere/AppServer/profiles

The location where theWebSphere profile is to becreated. This directory is onthe BI node computer's filesystem.

WebSphere Profile Name COGNOSProfile The name of the WebSphereprofile that is used for IBMCognos BI.

WebSphere Host Name This value is automaticallyentered.

The name or IP address ofthe BI node computer.

WebSphere Profile templatelocation

/opt/IBM/WebSphere/AppServer/profileTemplates/default

The location where theWebSphere profile templatesare located.

Table 9. IBM Cognos BI Server parametersField Default or example value Description

Database Host Name This value is automaticallyentered.

The name or IP address ofthe Data node computer.


The name or IP address ofthe BI node.

Cognos DispatcherApplication Server Port

9080 The HTTP transport portnumber for the WebSphereApplication Server whereIBM Cognos is running.

Database Server Host Name This value is automaticallyentered.

The name or IP address ofthe Data node.


Table 10. WebSphere Message Broker installation parametersField Default or example value Description

WebSphere Message BrokerInstallation Location

/opt/ibm/mqsi/8.0.0.1 The location whereWebSphere Message Brokeris to be installed. Thisdirectory is on the EnterpriseService Bus (ESB) nodecomputer's file system.

WMB ODBC DatabaseExtender Install Location

/opt/ibm/IE02/2.0.0 The location whereWebSphere Message BrokerODBC Database Extender isto be installed. This directoryis on the Enterprise ServiceBus (ESB) node computer'sfile system.

WebSphere Message BrokerExplorer InstallationDirectory

/opt/IBM/MBExplorer The location whereWebSphere Message BrokerExplorer is to be installed.This directory is on theEnterprise Service Bus (ESB)node computer's file system.

Table 11. WebSphere Message Broker and Queue installation parametersField Default or example value Description

ESB Deployment Location /var/PMQ The location wherePredictive Maintenance andQuality files can be placed.

Location of the IBM DataServer Driver for ODBCand CLI

/var/odbc_cli The location where youdownloaded the IDM DataServer Driver.

This directory is on the ESBnode computer's file system.

Broker Name pmqbroker The broker to be created.

Queue Manager Name pmqmanager The Queue Manager name tobe created.

Execution Group pmqgroup The name of a group ofmessage flows that areassigned to a broker

Specify Database Node IPAddress

This value is automaticallyentered.

The name of IP address ofthe Data node computer.

Table 12. WebSphere Message Broker installation parametersField Default or example value Description

MDM Collaboration ServerInstallation Directory

/opt/IBM/MDMPIM The location where MasterData ManagementCollaboration Server is to beinstalled.

This directory is on theMDM node computer's filesystem.


Table 13. InfoSphere Master Data Management parametersField Default or example value Description


The location where theWebSphere profile is to becreated. This directory is onthe MDM node computer'sfile system.

WebSphere Profile Name MDMProfile The name of the WebSphereprofile that is used forInfoSphere Master DataManagement.


The name or IP address ofthe MDM node computer.

Default WebSphereTemplate Path


The location where theWebSphere profile templatesare located.

MDM DB2 Host Name This value is automaticallyentered.


Perl Installation Directory /opt/ActivePerl-5.16 The location where youinstalled Active Perl.

This location on the MDMnode computer.

Table 14. IBM SPSS Collaboration and Deployment Server parametersField Default or example value Description

SPSS Collaboration andDeployment ServicesInstallation Directory

/opt/IBM/SPSS/Deployment/5.0/Server

The location where IBM SPSSCollaboration andDeployment Services is to beinstalled. This location is onthe Analytics nodecomputer's file system.


The location where theWebSphere profile is to becreated. This directory is onthe Analytics nodecomputer's file system.

WebSphere Profile DefaultTemplate Location


The location where theWebSphere profile templatesare located. This directory ison the Analytics nodecomputer's file system.

WebSphere Profile Name SPSSProfile The name of the WebSphereprofile that is used for theSPSS products.


The name or IP address ofthe Analytics node computer.

SPSS DB2 Database HostName

This value is automaticallyentered.


Modeler Server InstallationDirectory

usr/IBM/SPSS/ModelerServer/15.0

The directory where the IBMSPSS Modeler Server is to beinstalled. This directory is onthe Analytics node computer.


Table 14. IBM SPSS Collaboration and Deployment Server parameters (continued)Field Default or example value Description

SPSS Collaboration andDeployment ServicesEnterprise ViewerInstallation Directory

/opt/IBM/SPSS/Deployment/5.0/EnterpriseViewDriver

The directory where the IBMSPSS Collaboration andDeployment ServicesEnterprise View Driver is tobe installed. This directory ison the Analytics nodecomputer.

SPSS Collaboration andDeployment ServicesPython InstallationDirectory

/opt/IBM/SPSS/Deployment/5.0/PythonEssentials

The directory where the IBMSPSS Collaboration andDeployment Services PythonScripting Essentials is to beinstalled. This directory is onthe Analytics node computer.

SPSS Data Access PackInstallation Directory

/root/SDAP61 The directory where the IBMSPSS Data Access Pack is tobe installed. This directory ison the Analytics nodecomputer.

SPSS Statistics InstallationDirectory

/opt/IBM/SPSS/StatisticsServer21

The directory where the IBMSPSS Statistics Server is to beinstalled. This directory is onthe Analytics node computer.

Starting the installationAfter you enter all of the required fields in the Deployment Wizard, you can startthe installation and configuration of the IBM Predictive Maintenance and Qualitycomponents.

Procedure

On the Summary Panel of the Deployment Wizard, click Deploy all.

Note: If you choose to deploy the tasks individually, you must click Deploy taskfor each task in the order that the tasks appear on the Summary panel.

Configure the server components and test the installationAfter the installation of the IBM Predictive Maintenance and Quality servercomponents is complete, you must perform some additional configuration tasksand then test the installation.

Testing the database installation and configurationYou can test the database installation and configuration by logging in to the Datanode computer and listing the databases on the server. You can also list thedatabases available on each node computer where the IBM DB2 client wasinstalled.

Procedure1. Log on to the Data node computer.

a. Open a terminal window, and change to the database instance owner user.For example, su - db2inst1.


b. Enter the following command to list the databases on the computer:db2 list database directory

The following databases are listed:v COG102DBv MDMDBv SPSSDB

2. Log on to the Business Intelligence (BI) node computer.a. Open a terminal window, and change to the database client user. For

example, su - db2inst1.b. Enter the following command to list the databases on the computer:

db2 list database directory

COG102DB is listed.3. Log on to the Predictive Analytics node computer.

a. Open a terminal window, and change to the database client user. Forexample, su - db2inst1.


SPSSDB is listed.4. Log on to the Master Data Management (MDM) node computer.

a. Open a terminal window, and change to the database client user. Forexample, su - db2inst1.


MDMDB is listed.

Configuring WebSphere Application Server for IBM Cognos BITo complete the installation of the IBM Predictive Maintenance and Quality servercomponents, you must configure properties in IBM WebSphere Application Serverfor IBM Cognos Business Intelligence.

Procedure1. Open a web browser.2. In the address bar, type the address for the WebSphere Admin Console that

was installed on the BI node computer.The Admin console address is: http://bi_node_name:9060/ibm/console. Wherebi_node_name is the name or IP address for the BI node computer.

3. Expand Servers > Server Types > WebSphere application servers, and clickserver1.

4. Under Server Infrastructure, expand Java and Process Management, andclick Process Definition.

5. Under Additional Properties, click Java Virtual Machine.6. In the Initial Heap Size box, enter 512.7. In the Maximum Heap Size box, enter 1024.8. Click Apply, and then click Save.9. Under Additional Properties, click Environment Variables.

10. Click New.11. In the Name box, enter LD_LIBRARY_PATH.


12. In the Value box, enter the path the IBM Cognos BI bin64 directory. Forexample, enter /opt/ibm/cognos/c10_64/bin64/.

Important: If you changed the default value in the Cognos BI InstallationLocation field in the Deployment Wizard, ensure you use the path youentered.

13. Click Apply, and then click Save.

Saving your IBM Cognos Configuration settings and startingthe services

You must save the configuration settings in IBM Cognos Configuration before youcan start the IBM Cognos application in WebSphere Application Server.

Procedure1. Log in to the BI node computer as root.2. Go to the /opt/ibm/cognos/c10_64/bin64 directory.3. Type the following command:

./cogconfig.sh

IBM Cognos Configuration starts.4. Click File > Save.5. Close IBM Cognos Configuration.

Important: If you are prompted to start the Cognos Content Database service,click No.

6. Log in to the BI node computer as root using a terminal emulator, such asPuTTY.

Note: Using a terminal emulator like PuTTY ensures that the proper profile isloaded.

7. Go to the WebSphere Application Server Profile Location. For example, go tothe /opt/IBM/WebSphere/AppServer/profiles/COGNOSProfile/bin directory ifyou used the default path in the Deployment Wizard.

8. Type ./stopServer.sh server1 to stop WebSphere Application Server.9. Type ./startServer.sh server1 to start WebSphere Application Server.

Results

WebSphere Application Server is configured for IBM Cognos BI.

It may take several minutes for all of the IBM Cognos services to start for the firsttime.

Setting the password for the mqm user on the ESB nodecomputer

You must set the password for the mqm user on the Enterprise Service Bus (ESB)node computer.

Procedure1. Log in to the ESB node computer as root.2. Type the following command:

passwd mqm


3. Enter mqm and the new password.You do not have to use mqm. It is only a suggestion. If you do use mqm, you willsee a message saying that your password is too weak. But, you can ignore themessage.

Testing the installation of the server componentsYou can test the installation of the IBM Predictive Maintenance and Quality servercomponents by accessing some of the component portals.

For example, you can open the IBM Cognos BI portal on the BI node. If the portalopens, IBM Cognos BI is installed and running. You can also access the SPSSconfiguration tool on the Analytics node computer.

Procedure1. Open a web browser.2. In the address bar, type the address for the IBM Cognos Content Manager

status page.The address is http://bi_node_name:9080/p2pd/servlet, where bi_node_name isthe name or IP address for the BI node computer.The Content Manager status says Running.

3. In the address bar, type the address for the IBM Cognos BI portal.The address is http://bi_node_name/ibmcognos/, where bi_node_name is thename or IP address for the BI node computer.

Note: Ensure that you add the trailing / to the URL.IBM Cognos Connection appears.

4. In the address bar, type the address for the SPSS administration console.The address is http://analytics_node_name:9080/config, whereanalytics_node_name is the name or IP address for the Analytics nodecomputer.The SPSS administration console appears.

Computer firewall settings to run the server componentsEach IBM Predictive Maintenance and Quality node computer requires certainports to be opened for the server components to operate in a multi-computersolution, and you must configure your firewall settings for each specific node.

Configuring your firewall settings for all nodesOn each computer on which you install an IBM Predictive Maintenance andQuality node, you must open specific ports.

The following ports must be open:v vnc-serverv x11v 5901v 5902v 5903v 6001v 6002


v 6003v 22

Procedure1. Log in as root.2. Back up your existing firewall settings by typing the following command:


3. Add rules for the ports with the following command:iptables -I INPUT -m state --state NEW -m tcp -p tcp --dport port_number -j ACCEPT

For example, to open vnc-server, type the following commandiptables -I INPUT -m state --state NEW -m tcp -p tcp --dport vnc-server -j ACCEPT




The added port should appear in the list.7. Repeat these steps on each computer on which you install a Predictive

Maintenance and Quality node.

Configuring your firewall settings for the Analytics nodecomputer

You must ensure that certain ports are open on the Predictive Analytics nodecomputer for IBM Predictive Maintenance and Quality.

The following ports must be open:v 45088v 58313v 28052v tungsten-httpsv glrpcv corbalocv 59356v 9043v 9060

Procedure1. Log in to the Analytics node computer as root.2. Back up your existing firewall settings by typing the following command:




4. Repeat the previous step for each of the required port values.






Configuring your firewall settings for the BI node computerYou must ensure that certain ports are open on the Business Intelligence (BI) nodecomputer for IBM Predictive Maintenance and Quality.

The following ports must be open:v 9362v vracev 9663v corbalocv 9043v glrpcv httpv tungsten-httpsv 9060v 6001v 6002v 6003v 5901v 5902v 5903

Procedure1. Log in to the BI node computer as root.2. Back up your existing firewall settings by typing the following command:




4. Repeat the previous step for each of the required port values.5. Type the following command to save your firewall settings:






Configuring your firewall settings for the ESB node computerYou must ensure that certain ports are open on the Enterprise Service Bus (ESB)node computer for IBM Predictive Maintenance and Quality.

The following ports must be open:v boksv boks_clntdv boks_servmv boks_servcv ibm-mqseries

Procedure1. Log in to the ESB node computer as root.2. Back up your existing firewall settings by typing the following command:



For example, to open boks, type the following commandiptables -I INPUT -m state --state NEW -m tcp -p tcp --dport boks -j ACCEPT






Configuring your firewall settings for the MDM node computerYou must ensure that certain ports are open on the Master Data Management(MDM) node computer for IBM Predictive Maintenance and Quality.

The following ports must be open:v 9060v tungsten-httpsv 50498v 9634v 9633v 57537v 49888v 53343v 41950v 60573v 43420v 40187v netsteward


v corbalocv glrpcv 44152v 43830v 39188v 9043v 7507v 49298v 8881v cddbp-altv 40752v 50512v 35086v bacula-dirv jetdirectv 55052v 32970v commplex-linkv 37253v 9060

Procedure1. Log in to the MDM node computer as root.2. Back up your existing firewall settings by typing the following command:









Configuring your firewall settings for the Data node computerYou must ensure that certain ports are open on the Data node computer for IBMPredictive Maintenance and Quality.

The following ports must be open:v ibm-db2v db2c_db2inst1


Procedure1. Log in to the Data node computer as root.2. Back up your existing firewall settings by typing the following command:



For example, to open ibm-db2, type the following commandiptables -I INPUT -m state --state NEW -m tcp -p tcp --dport ibm-db2 -j ACCEPT






Chapter 4. Installation of the server artifactsThe server artifacts include report content and workflows for IBM PredictiveMaintenance and Quality. The installation program will install artifacts on eachnode computer.

Starting the installer for the server artifactsUse the Launchpad to start the IBM Predictive Maintenance and Quality serverartifacts installer.

Before you begin

Ensure that you are logged in as root.

You must have a Firefox, version 10 or earlier, or SeaMonkey, version 2.9 or earlier,web browser installed and set as your default web browser on the computer fromwhere you run the installation.


the directory where you copied the installation files.2. Go to the ServerArtifacts/disk1 directory.3. Type the following command to change the permissions for the installation

files:chmod -R 755 *

4. Enter the following command:./launchpad.sh

5. Review the information in the Launchpad panels.6. Click Install Server Artifacts > Predictive Maintenance and Quality Server

Artifacts Accelerator to start the Deployment Wizard to install the serverartifacts.

7. Follow the prompts to install the server artifacts.8. On the Select Tasks page, select all nodes.

Setting port numbers for the Deployment Wizard to useIf you opened ports for the installation of IBM Predictive Maintenance and Qualitycomponents, you must set those port numbers in the Deployment Wizard.

Procedure1. In the Deployment Wizard, click Edit > Preferences.

The Deployment Preferences window appears.2. Enter 30000 in the Data Port Number box.


3. Enter 35000 in the Communication Port Number box.



4. If you are using the computer on which you are running the installation as anode, do the following steps:a. Click Target Computer Settings.b. Select localhost in the Target Computer field.c. Enter the communication port number that you set in the Communication

Port field. For example, enter 35000.

Note: The RMI Registry Port is unavailable if you are using localhost as anode.

Specifying the target computers on which you will install the serverartifacts

You must specify a each computer on which you installed an IBM PredictiveMaintenance and Quality node. Ensure that you identify the correct computer foreach node.

Before you begin

You must have root access on each computer on which you install a node.

You might have to change a setting in a configuration file on your target computerto allow the Deployment Wizard to access the computer as root. Use thefollowing steps if you receive a message that says the connection to the targetcomputer was refused:1. On the target computer, go to the /etc/ssh directory and open sshd_config for

editing.2. Change the PermitRootLogin property to yes.3. Save the file. You may have to restart the server for the change to take effect.

Procedure1. On the Specify Target Computers pages of the Deployment Wizard, enter the

name or IP address of the computer on which you installed the node you areprompted for in the Target Computer box.The Deployment Wizard prompts you for each node computer.If you installed a node on the computer where you are running theDeployment Wizard, enter localhost.

2. Click Add.a. When you enter a computer other than localhost, in the Target Computer

Credentials box, enter the User ID and Password for the root user.

Important: Ensure that you enter the credentials for the root user on thetarget computer.

b. Click Test Login.c. Click Add.

The computer that you entered appears in the Selected target computersbox.

3. Do the following steps if you opened ports for the installation.a. Click Edit > Preferences.


b. Click Target Computer Settings.c. Select the computer name or IP address in the Target Computer field.d. Enter the communication port number that you set in the Communication

Port field. For example, enter 35000.e. Enter the Data Port Number that you set in the RMI Registry Port field.

For example, enter 30000.

Note: If you are using localhost as a node in the installation, the RMIRegistry Port is unavailable.

4. In the Selected target computers box, select the target computer, and click TestConnections.

Important: Test Connections tests the connection, tests the credentials, andlocates or enables a deployment agent on the target computer. You must havean active deployment agent on each target computer.If you receive an error message after you click Test Connections, you mighthave to change some settings on your computers.v Edit your iptable settings or temporarily disable your firewall. For moreinformation, see Computer firewall settings required for the installation onpage 9.

v Compare and correct your domain name system (DNS) settings for eachcomputer. For example, type sudo system-config-network. Select DNSconfiguration, and ensure that your host name domain and DNS search pathsettings are correct.

v Ensure that the /etc/host file has the correct entries.5. Click Next.6. Repeat the steps for each node computer.

Configuring parameters for the server artifacts installationThe Deployment Wizard displays some default values for each component. Youcan accept the default values or change them to suit your environment.

Procedure

Use the following table to verify or enter values in each field on each panel of theDeployment Wizard.

Table 15. Data node parametersField Default or example value Description

Data Node DeploymentLocation

/opt/IBM/PMQ/Data The location where theserver artifacts are to beinstalled on the Data nodecomputer.

DB2 Instance Owner UserName

db2inst1 The user ID that controls theDB2 processes and owns thedirectories that are used bythe database instance.

Chapter 4. Installation of the server artifacts 33

Table 15. Data node parameters (continued)Field Default or example value Description

DB2 Instance OwnerPassword


The password for the DB2instance owner user.Note: Ensure that you usethe same password as youprovided during the serverinstallation.

Table 16. Enterprise Service Bus (ESB) node parametersField Default or example value Description

Enterprise Service Bus NodeDeployment Location

/var/PMQ The location where theserver artifacts are to beinstalled on the ESB nodecomputer.

Installation Location ofMessage Broker

/opt/ibm/mqsi/8.0.0.1 The location whereWebSphere Message Brokeris installed. This directory ison the ESB node computer'sfile system.

Websphere Message QueueLocation

/opt/mqm The location whereWebSphere Message Queueis installed. This directory ison the ESB node computer'sfile system.

Broker Name pmqbroker The broker name that youcreated.

Queue Manager Name pmqmanager The Queue Manager namethat you created.

Execution Group pmqgroup The name of a group ofmessage flows that areassigned to a broker that youcreated.

PMQIntegration SPSSWebService URL

http://analytics_node_name:port/scoring/services/Scoring.HttpV1

Where analytics_node_nameis the name or IP address ofthe Predictive Analytics nodecomputer, and port is theHTTP port for theWebSphere instance, forexample 9080.

PMQMaximoIntegrationSPSS WebService URL

http://analytics_node_name:port/meaweb/services/EXTSYS1_MXWOInterface

Where analytics_node_nameis the name or IP address ofthe Analytics node computer,and port is the HTTP portfor the WebSphere instance,for example 9080.

Table 17. Business Intelligence (BI) node parametersField Default or example value Description

Business IntelligenceDeployment Location

/opt/IBM/PMQ/BI The location where theserver artifacts are to beinstalled on the BI nodecomputer.


Table 17. Business Intelligence (BI) node parameters (continued)Field Default or example value Description

Cognos Install Location /opt/ibm/cognos/c10_64 The location where IBMCognos BI is installed. Thisdirectory is on the BI nodecomputer's file system.

WebSphere Install Location /opt/IBM/WebSphere/AppServer

The location whereWebSphere is installed. Thisdirectory is on the BI nodecomputer's file system.

DB2 Instance HomeDirectory

/home/db2inst1 The home directory of thedatabase instance owner.

Cognos BI Dispatcher URI http://bi_node_name:9080/p2pd/servlet/dispatch

The URL to the IBM CognosBI dispatcher, wherebi_node_name is the name orIP address of the BI nodecomputer.

DB2 Database Instance UserName

db2inst1 The user ID for the IBMCognos content storedatabase.

DB2 Database InstancePassword


The password for thedatabase instance owneruser.

DB2 Database Port Number 50000 The port number for the IBMDB2 database server.

DB2 Database Hostname There is no default value forthis field.


Table 18. Analytics node parametersField Default or example value Description

Analytics DeploymentLocation

/opt/IBM/PMQ/Analytics The location where theserver artifacts are to beinstalled on the Analyticsnode computer.

Modeler Server InstallLocation

/usr/IBM/SPSS/ModelerServer/15.0

The location where theModeler Server is installed.

Collaboration andDeployment Services InstallLocation

/opt/IBM/SPSS/Deployment/5.0/Server

The location where IBM SPSSCollaboration andDeployment Services isinstalled. This location is onthe Analytics node computer.

Table 19. Master Data Management (MDM) node parametersField Default or example value Description

Master Data DeploymentLocation

/opt/IBM/PMQ/MDM The location where theserver artifacts are to beinstalled on the MDM nodecomputer.


Starting the installation of the server artifactsAfter you enter all of the required fields in the Deployment Wizard, you can startthe installation of the server artifacts.

Procedure

On the Summary Panel of the Deployment Wizard, click Deploy all.

Note: If you choose to deploy the tasks individually, you must click Deploy taskfor each task in the order that the tasks appear on the Summary panel.

Complete the configuration of the server componentsAfter you have installed the IBM Predictive Maintenance and Quality serverartifacts, you can complete the configuration of the server components.

Verifying the configuration of IBM SPSS Collaboration andDeployment Services

To complete the configuration of IBM SPSS Collaboration and Deployment ServicesServer, you must verify the URL Prefix value for your environment.

Procedure1. Open a web browser.2. In the address bar, type the address for the Collaboration and Deployment

administration console.The address is http://analytics_node_name:9080/config, whereanalytics_node_name is the name or IP address for the Predictive Analyticsnode computer.

3. Enter the Login name and Password for the administrator user, and clickLogin.The default Login name is admin, and the default Password is admin.

4. On the Configuration panel, under Setup, click URL Prefix.5. In the URL Prefix box, verify that the address is http://

analytics_node_name:9080, where analytics_node_name is the name or IPaddress of the Analytics node computer.

6. If the value is correct, you do not have to complete the remaining steps in thistask.

7. If the value is not correct, enter the name or IP address of the Analytics nodecomputer, and click Set.

8. Open the WebSphere Administrative Console in your web browser.The address is http://analytics_node_name:9060/ibm/console, whereanalytics_node_name is the name or IP address for the Analytics nodecomputer. 9060 is the default port number for the WebSphere AdministrativeConsole.

9. Click Log in.You do not need to enter a value in the User ID box.

10. Under Applications > Application Types > WebSphere EnterpriseApplications, selectIBM_SPSS_Collaboration_and_Deployment_Services_5.0, and click Stop.


11. Select IBM_SPSS_Collaboration_and_Deployment_Services_5.0, and clickStart to restart the application and apply the changes.

Configuring the MDM nodeTo configure the Master Data Management (MDM) node, you must log in to theMDM administration console and import content files.

The content files are installed onto the MDM node computer by the Server Artifactinstaller. You must copy the content files from the MDM node to a computer whereyou have Microsoft Internet Explorer installed.

Procedure1. Copy the MDM node contents to your Microsoft Windows-based computer

with an FTP client or by using a shared directory.The contents files are installed to /opt/ibm/PMQ by default on the MDM nodecomputer. The contents file is named IBMPMQ.zip.

2. In Microsoft Internet Explorer, go to the MDM administration console.The address is http://mdm_node_name:7507/utils/enterLogin.jsp, wheremdm_node_name is the name or IP address of the MDM node computer.

3. In User name, enter Admin.

Note: These values are case-sensitive.4. In the Password box, enter trinitron.5. In the Company box, enter IBMPMQ.6. Click Login.7. Click System Administrator > Import Environment.8. In the Import Company Environment box, browse to and select the

IBMPMQ.zip file that you copied.9. Click Import.

10. Log out, and log back in to the MDM administration console to ensure thatthe import was completed.


Chapter 5. Installation of the client componentsThere are several client components that are included with IBM PredictiveMaintenance and Quality. You can install the components as you require.

Important: The client components must be installed on computers running theMicrosoft Windows 7 64-bit operating system.

Important: Install the client components only after you successfully install theserver components.

Client componentsThe following client components for IBM Predictive Maintenance and Quality areavailable to be installed.

Database connectivity

IBM DB2 Connect must be installed to enable connectivity to the analyticsdatabase.

Predictive modeling and decision management

Install the following components so that you can modify or create predictivemodels and so that you can perform decision management tasks:v IBM SPSS Collaboration and Deployment Services Deployment Managerv IBM SPSS Modeler Clientv IBM SPSS Statistics Clientv IBM SPSS Text Analytics Client

Optionally, install the following components:v IBM SPSS Collaboration and Deployment Services Documentationv IBM SPSS Decision Management Documentationv IBM SPSS Modeler Client Documentationv IBM SPSS Statistics Desktop

Business intelligence

Install IBM Cognos Framework Manager so that you can modify the reportingmodel metadata.

Optionally, install the following components:v IBM Cognos Business Intelligence Samplesv IBM Cognos Dynamic Query Analyzerv IBM Cognos for Microsoft Officev IBM Cognos Lifecycle Managerv IBM Cognos Mobilev IBM Cognos Real-time Monitoringv IBM Cognos Software Development Kit


v IBM Cognos Supplementary Languages Documentation

Enterprise service bus

Install the following components:v WebSphere Message Broker Toolkitv WebSphere MQ for Windows

Use the WebSphere Message Broker Toolkit to create, manage, deploy, and deletemessage flows and associated resources in a development environment.

Starting the installer for the client componentsThe IBM Predictive Maintenance and Quality client installers are provided on thesame USB hard disk drive as the server and content installers.

Important: The Deployment Wizard copies the installers to your computer. Youmust run each installer individually after they are copied to your computer.

Procedure1. Insert the Predictive Maintenance and Quality USB hard disk drive into the

USB port of your Microsoft Windows 7-based computer.2. Go to the Client/disk1 directory.3. Double-click launchpad64.exe.4. Review the information in the Launchpad panels.5. Click Install Client > Predictive Maintenance and Quality Client Accelerator

to start the Deployment Wizard.6. On the Select Tasks panel, select the groups of clients you want to install, and

click Next to select the client components that you want to install.

Important: The required client components include the following:v WebSphere Message Broker Toolkitv WebSphere MQ for Windowsv IBM SPSS Collaboration and Deployment Services Deployment Managerv IBM SPSS Modeler Clientv IBM SPSS Statistics Desktopv IBM SPSS Statistics Clientv IBM SPSS Text Analytics Clientv IBM Cognos Framework Manager

7. Enter a location for each client component installer to be copied to. The defaultis C:\IBM\PMQ\Client Installer.

8. On the Summary Panel, click Deploy all.9. After the client installers are copied to your computer, you must install each

client individually by using its installer.

Installing IBM SPSS Collaboration and Deployment ServicesDeployment Manager

You must install IBM SPSS Collaboration and Deployment Services DeploymentManager to complete the configuration of IBM Predictive Maintenance and Quality.


Install IBM SPSS Collaboration and Deployment Services Deployment Manager ona computer running the Microsoft Windows 7 operating system.

Procedure1. Go to the install_location\Client Installer\Analytics\IBM SPSS

Collaboration and Deployment Services Deployment Manager directory.By default, the install_location is C:\IBM\PMQ\.

2. Extract the installer files from the zip file.3. Double-click install.exe to start the IBM SPSS Collaboration and Deployment

Services Deployment Manager installation.4. Follow the steps in the wizard to install the client component.

For more information about the installation of Deployment Manager, see theIBM SPSS documentation (pic.dhe.ibm.com/infocenter/spsscads/v5r0m0/index.jsp).

Adding a content server connection for IBM SPSSCollaboration and Deployment Services

You must add a connection to your IBM SPSS Collaboration and DeploymentServices repository in the IBM SPSS Collaboration and Deployment ServicesDeployment Manager client.

After you add the connection, the server folder displays in the Content Explorer,and you can log in to the server.

Procedure1. On your Microsoft Windows computer, start IBM SPSS Collaboration and

Deployment Services Deployment Manager. For example, click Start >Deployment Manager.

2. Click File > New > Content Server Connection.3. In the Connection Name box, enter a name for your Collaboration and

Deployment Services repository.4. In the Host box, enter the name or IP address of the Predictive Analytics node

computer.5. In the Port box, enter 9080.

9080 is the port number used by the WebSphere Application Server instance.6. Click Finish.7. Click the connection name that you created.8. In the User ID box, enter admin.9. In the Password box, enter admin.

10. Click OK.

Adding users and groups to IBM SPSS Collaboration andDeployment Services

You use IBM SPSS Collaboration and Deployment Services Deployment Managerto manage users and groups. You must add an administrator user for IBMPredictive Maintenance and Quality.

Procedure1. In Deployment Manager, click Tools > Server Administration.2. Click Click here to define a new administrative server connection.

Chapter 5. Installation of the client components 41

3. In the Name box, enter a name for your server, and click Next.4. In the Host box, enter the name or IP address of Predictive Analytics node

computer.5. In the Port box, enter the port number of for the WebSphere instance. The

default value is 9080.6. Click Finish.7. Double-click the connection name that you created.8. In the User ID box, enter admin.9. In the Password box, enter admin.

10. Click OK.11. Expand Users and Groups, and double-click Local User Repository.12. Select Show all available users/groups.13. Click New Group.

a. Enter administrator.b. Select Show all available users.c. Under Available users, move the admin user to Groups contains users.d. Click OK.

14. Click New Group.a. Enter DM Administrator.b. Select Show all available users.c. Under Available users, move the admin user to Groups contains users.d. Click OK.

15. Click New Group.a. Enter DM Users.b. Select Show all available users.c. Under Available users, move the admin user to Groups contains users.d. Click OK.

16. Double-click Roles.17. Click New Role.

a. In the Role Name box, enter DM Administrator.b. Click Select All to add all actions for this user role.c. Click OK.d. Select the DM Administrator role, and click Edit Users and Groups.e. Click Show all available users/groups.f. Under Available users, move the DM Administrator group to

Users/Groups Assigned to Role.g. Click OK.

18. Click New Role.a. In the Role Name box, enter DM User.b. Click Select All to add all actions for this user role.c. Clic

Documents

Pmq Installation Guide