Embed Size (px)
Citation preview
■ High luminous Intensity and high efficiency
■ Based on Blue : InGaN technology
■ Wide viewing angle : 120°
■ Excellent performance and visibility
■ Suitable for all SMT assembly methods
■ IR reflow process compatible
■ Environmental friendly; RoHS compliance
Features :
PLCC 2835 18V LC Datasheet
PLCC Series
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 1
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 2
Table of Contents
General Information .........................................................................................................................................................3
Absolute Maximum Ratings ..........................................................................................................................................4
Characteristics ....................................................................................................................................................................4
Luminous Flux Characteristic ........................................................................................................................................5
Voltage Bin Structure .......................................................................................................................................................5
Mechanical Dimensions ..................................................................................................................................................6
CCT Bins ................................................................................................................................................................................7
Characteristic Curve .........................................................................................................................................................11
Reflow Profile ......................................................................................................................................................................18
Reliability ..............................................................................................................................................................................19
Product Packaging Information ...................................................................................................................................20
Revision History .................................................................................................................................................................21
About Edison Opto ...........................................................................................................................................................21
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 3
Ultra high luminous efficacy, combined with the flexibility in design due to its slim and miniature size, PLCC LED Series are optimized to be used as lighting for signboard.
2 T 0 3 X 5 x W x x 0 0 0 x x xX1 X2 X3-X4 X5-X6 X7-X8 X9-X10 X11-X13 X14-X16
X1 X2 X3-X4 X5-X6 X7-X8
Type Component Series Wattage Color
2 Emitter T PLCC 03 3528 X5 0.5W CW Cool White
NW Neutral White
WW Warm White
X9-X10 X11-X13 X14-X16
Internal code PCB Board Serial Number
- - 000 - - -
Ordering Code Format
General Information
Introduction
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 4
Absolute maximum ratings (Ta=25oC)
Notes: 1. 2θ1/2 is the off-axis angle where the luminous intensity is half of the axial luminous intensity.2. Color rendering index CRI Tolerance: ±23. CIE_x/y tolerance: ±0.005
Characteristics
Parameter Symbol Value Units
Viewing Angle (Typ.) 2Θ1/2 120 Degree
Thermal resistance - 16 oC/W
CRI - 78 -
CCT (6500K) (4000K)
(3000K)(2700K)
-
X: 0.3224, Y: 0.3517X: 0.3892, Y: 0.3894X: 0.4485, Y: 0.4077X: 0.4687, Y: 0.4151
2.7, 5.7, 8- Step
JEDEC Moisture Sensitivity -
Level 2aFloor Life
Conditions: ≤30˚C / 60% RHSoak Requirements(Standard)
Time (hours): 120+1/-0Conditions: 60˚C / 60% RH
-
Absolute Maximum Ratings
Parameter Symbol Value Units
Forward Current IF 40 mA
Pulse Forward Current (tp<=100μs, Duty cycle=0.25) Ipulse 60 mA
Reverse Current IR 10 uA
Reverse Voltage VR [2] V
LED Junction Temperature TJ 125 °C
Operating Temperature - -40 ~ +85 °C
Storage Temperature - -40 ~ +125 °C
ESD Sensitivity (HBD) VB 2,000 V
Soldering Temperature TsReflow Soldering : 255~260oC/10~30sec
Manual Soldering : 350oC/3sec
Notes: 1. Proper current derating must be observed to maintain junction temperature below the maximum at all time.2. LEDs are not designed to be driven in reverse bias.
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 5
Luminous Flux Characteristic
Luminous Flux Characteristics, IF=30mA and TJ=25˚C
Note: The luminous flux performance is guaranteed within published operating conditions. Edison Opto maintains a tolerance of ±10% on flux measurements.
Voltage Bin Structure
Group Min. Voltage (V) Max. Voltage (V)
V17 17 18
V18 18 19
V19 19 20
Note:Forward voltage measurement allowance is ± 0.2V.
Color Group Min. Luminous Flux(lm)
Max. Luminous Flux(lm)
Forward Current(mA) Order Code
Cool White
55 55 60
30
2T03X5CW1100000660 60 65
65 65 70
70 70 75
Neutral White
55 55 60
2T03X5NW1100000660 60 65
65 65 70
70 70 75
Warm White
55 55 60
2T03X5WW1100000660 60 65
65 65 70
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 6
Notes: 1. All dimensions are measured in mm.2. Tolerance : ± 0.20 mm
Circuit
1
(+) (-)
2
0.75
1.75
0.58
0.70
0.45
2.80
1.70
3.50
Solder Pad
(-)(+)
1.95
0.38
2.121.2
Mechanical Dimensions
1 2
1 2
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 7
CCT Bins
Center point (in cold) : X: 0.3224, Y: 0.3517BIN0: XP→2.7 SDCMBIN1: X1→5.7 SDCM BIN2: X2→5.7~8 SDCM
6500K
X1R
X2R
X2L
X1L
CCT-X
0.39
0.38
0.37
0.36
0.35
0.34
0.33
0.32
0.31 0.3 0.305 0.31 0.315 0.32 0.325 0.33 0.335 0.34 0.345
CCT-
Y
XP0
Steps Cx Cy a b theta
2.7 0.3224 0.3517 0.009072 0.00324 65.38
5.7 0.3224 0.3517 0.019150 0.00680 65.38
8 0.3224 0.3517 0.026880 0.00960 65.38
XPB XPA
X Y X Y
0.3144 0.3617 0.3018 0.3364
0.3270 0.3870 0.3144 0.3617
0.3430 0.3670 0.3304 0.3417
0.3304 0.3417 0.3178 0.3164
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 8
S2R
Center point (in cold) : X:0.3892; Y:0.3894BIN0: SP→2.7 SDCMBIN1: S1→5.7 SDCM BIN2: S2→5.7~8 SDCM
4000K
S1R
S2R
S2L
S1L
CCT-X
0.43
0.42
0.41
0.40
0.39
0.38
0.37
0.36
0.35
CCT-
Y
Steps Cx Cy a b theta
2.7 0.3892 0.3894 0.008829 0.003483 60.51
5.7 0.3892 0.3894 0.018640 0.007350 60.51
8 0.3892 0.3894 0.026160 0.010320 60.51
XPB XPA
X Y X Y
0.3812 0.3994 0.3662 0.3757
0.3962 0.4230 0.3812 0.3994
0.4122 0.4030 0.3972 0.3794
0.3972 0.3794 0.3822 0.3557
SP0
0.365 0.37 0.375 0.38 0.385 0.39 0.395 0.4 0.405 0.41 0.415
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 9
Center point (in cold) : X:0.4485; Y:0.4077BIN0: NP→2.7 SDCMBIN1: N1→5.7 SDCM BIN2: N2→5.7~8 SDCM
3000K
N1R
N2R
N2L
N1L
CCT-X
0.45
0.44
0.43
0.42
0.41
0.40
0.39
0.38
0.37
CCT-
Y
Steps Cx Cy a b theta
2.7 0.3892 0.3894 0.008667 0.003699 60.51
5.7 0.3892 0.3894 0.018639 0.007350 60.51
8 0.3892 0.3894 0.026160 0.010320 60.51
NPB NPA
X Y X Y
0.4405 0.4177 0.4405 0.4177
0.4555 0.4413 0.4565 0.3977
0.4715 0.4213 0.4415 0.3741
0.4565 0.3977 0.4255 0.3941
0.425 0.43 0.435 0.44 0.445 0.45 0.455 0.46 0.465 0.47 0.475
NP0
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 10
Center point (in cold) : X: 0.4678, Y: 0.4151BIN0: MP→2.7 SDCM BIN1: M1→5.7 SDCM BIN2: M2→5.7~8 SDCM
2700K
CCT-X
M1R
M2R
0.4500
0.4400
0.4300
0.4200
0.4100
0.4000
0.3900
0.3800 0.44 0.446 0.452 0.458 0.464 0.47 0.476 0.482 0.488 0.494
CCT-
Y
MP0
M2L
M1L
Steps Cx Cy a b theta
2.7 0.4678 0.4151 0.00729 0.00378 53.7
5.7 0.4678 0.4151 0.01539 0.00798 53.7
8 0.4678 0.4151 0.02160 0.01120 53.7
MPB MPA
X Y X Y
0.4598 0.4251 0.4448 0.4051
0.4748 0.4451 0.4598 0.4251
0.4908 0.4251 0.4758 0.4051
0.4758 0.4051 0.4608 0.3851
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 11
Characteristic Curve
Color Spectrum
Color Spectrum at a typical CCT for PLCC 2835 18V LC
Nor
mal
ized
lum
inou
s In
tens
ity
Beam Pattern
Beam pattern diagram for PLCC seriesRadiation Angle
Nor
mal
ized
Lum
niou
s In
tens
ity
1.0
0.5
0
0° 10°20°
30°40°
50°
60°
70°
80°
90°1.00.5
Ta=25°C
-90o -60o -30o 0o
Wavelength(nm)
Cool White
Neutral White
Warm White
400 425 450 475 500 525 550 575 600 625 650 675 700 725
1.0
0.8
0.6
0.4
0.2
0
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 12
Forward Current vs. Forward Voltage
Forward Current vs. Forward Voltage for PLCC 2835 18V LC
Forw
ard
Curr
ent (
mA)
Relative Luminous Intensity vs. Forward Current
Relative Luminous Intensity vs. Forward Current for PLCC 2835 18V LC
Rela
tive
Lum
niou
s In
tens
ity
Forward Current (mA)
Forward Voltage (V)
48
40
32
24
16
8
016.5 17 17.5 18 18.5 19 19.5 20
0 5 10 15 20 25 30 35 40 45
1.2
1.0
0.8
0.6
0.4
0.2
0
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 13
Relative Luminous Flux vs. Junction Temperature
Relative Luminous flux vs. junction temperature for PLCC 2835 18V LC
Forward Voltage vs. Junction Temperature
Forward voltage vs. junction temperature for PLCC 2835 18V LCJunction Temperature (oC)
1.2
1.0
0.8
0.6
0.4
0.2
0
21
20
19
18
17
16
15
Forw
ard
Volta
ge (V
F)
0 20 40 60 80 100 120 140Junction Temperature (oC)
0 20 40 60 80 100 120 140
Rela
tive
Lum
inou
s Fl
ux
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 14
Δx,Δy vs. Forward Current
Δx,Δy vs. Forward Current for PLCC 2835 18V LC Cool WhiteForward Current (mA)
Δx Δy
Δx,Δy vs. Forward Current for PLCC 2835 18V LC Neutral White
5 10 15 20 25 30 35 40 45
0.015
0.010
0.005
0.000
-0.005
-0.010
-0.015
5 10 15 20 25 30 35 40 45
0.015
0.010
0.005
0.000
-0.005
-0.010
-0.015
Δx,
Δy
Δx,
Δy
Forward Current (mA)
Δx Δy
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 15
Δx,Δy vs. Junction Temperature
Δx Δy
Δx,Δy vs. Junction temperature for PLCC 2835 18V LC Cool White
Forward Current (mA)Δx,Δy vs. Forward Current for PLCC 2835 18V LC Warm White
5 10 15 20 25 30 35 40 45
0.015
0.010
0.005
0.000
-0.005
-0.010
-0.015
20 40 60 80 100 120 140
0.03
0.02
0.01
0.00
-0.01
-0.02
-0.03
Δx,
Δy
Δx,
Δy
Junction temperature (oC)
Δx Δy
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 16
Δx,Δy vs. Junction temperature for PLCC 2835 18V LC Warm WhiteJunction temperature (oC)
Δx Δy
Δx Δy
Δx,Δy vs. Junction temperature for PLCC 2835 18V LC Neutral WhiteJunction temperature (oC)
Δx,
Δy
0.03
0.02
0.01
0.00
-0.01
-0.02
-0.03
Δx,
Δy
20 40 60 80 100 120 140
20 40 60 80 100 120 140
0.03
0.02
0.01
0.00
-0.01
-0.02
-0.03
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 17
Maximum Current vs. Ambient Temperature
Max
imum
Cur
rent
(mA)
48
40
32
24
16
8
0 0 20 40 60 80 100 120 140
Maximum Current vs. Ambient Temperature for PLCC 2835 18V LC
Ambient Temperature (oC)
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 18
Reflow Profile
The following reflow profile is from IPC/JEDEC J-STD-020D which provided here for reference.
Notes:1. * Tolerance for peak profile temperature (Tp) is defined as a supplier minimum and a user maximum.2. ** Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum.
Profile Feature Pb-Free Assembly
Preheat & SoakTemperature min (Tsmin)Temperature max (Tsmax)Time (Tsmin to Tsmax) (ts)
150 °C200 °C
60-120 seconds
Average ramp-up rate (Tsmax to Tp) 3 °C/second max.
Liquidous temperature (TL)Time at liquidous (tL)
217 °C60-150 seconds
Peak package body temperature (Tp)* 255 °C ~260 °C *
Classification temperature (Tc) 260 °C
Time (tp)** within 5 °C of the specified classification temperature (Tc) 30** seconds
Average ramp-down rate (Tp to Tsmax) 6°C/second max.
Time 25oC to peak temperature 8 minutes max.
Classification Reflow Profiles
Reflow Profiles
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 19
Reliability
NO . Test Item Test Condition Remark
1 Temperature Cycle -40°C~100°C30, 30, mins 100 Cycle
2 Thermal Shock -40°C~100°C 15, 15 mins ≦10 sec 100 Cycle
3 Resistance to Soldering Heat TSOL=260°C, 30 sec 3 times
4 Moisture Resistance 25°C~65°C 90% RH 24 hrs / 1 cycle 10 Cycle
5 High-Temperature Storage TA=100°C 1,000 hrs
6 Humidity Heat Storage TA=85°CRH=85% 1,000 hrs
7 Low-Temperature Storage TA=-40°C 1,000 hrs
8 Operation Life test 25°C 1,000 hrs
9 High TemperatureOperation Life test 85°C 1,000 hrs
10 High Humidity Heat Life Test 85oC, 85%RH 1,000 hrs
11 ON/OFF Test 30 sec ON, 30 sec OFF 1.5W times
Item Criteria for Judgment
Min. Max.
Lumen Maintenance 85% -
Δu'v' - 0.006
Forward Voltage - Initial Data x 1.1
Reverse Current - 10 μA
Resistance to Soldering Heat No dead lamps or visual damage
Failure Criteria
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 20
Taping reel dimensions Package & label
Product Packaging Information
Item Quantity Total Dimensions (mm)
Reel 3,000pcs 3,000pcs R=178
Box 5 Reels 15,000pcs 240*235*67
Carton 5 boxes 75,000pcs 353*254*256
Starting with 50pcs empty, and 50pcs empty at the last
Seal
Moisture proof bag
Moisture absorbent material
Label
Reel Label
1.0 +0.25/-0
3.05±0.10
1.0±
0.1
3.65±0.10
T=0.25
3.65
±0.
10
2±0.054.0±0.1 4.0±0.101.5 +0.1/-0
3.5±
0.05
1.75
±0.
1
8.0±
0.2
www.edison-opto.com
Copyright © 2015 Edison Opto Corporation. All right reserved. The information in this document is subject to change without notice. version : 1 21
About Edison Opto
Edison Opto is a leading manufacturer of high power LED and a solution provider experienced in LDMS. LDMS is an integrated program derived from the four essential technologies in LED lighting applications- Thermal Management, Electrical Scheme, Mechanical Refinement, Optical Optimization, to provide customer with various LED components and modules. More Information about the company and our products can be found at www.edison-opto.com
Copyright©2015 Edison Opto. All rights reserved. No part of publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photo copy, recording or any other information storage and retrieval system, without prior permission in writing from the publisher. The information in this publication are subject to change without notice.
www.edison-opto.com
For general assistance please contact:[email protected]
For technical assistance please contact:[email protected]
Revision History
Versions Description Release Date
1 Establish a Datasheet 2015/04/10
