Plastic Cutting Tools

PRODUCTIONROUTING TOOLS

FOR MACHININGPLASTICS





ISO 9001 Certified

HIGH SPEED STEEL STRAIGHTHIGH SPEED STEEL STRAIGHT

SPIRAL "O" FLUTESPIRAL "O" FLUTE

DOUBLE EDGE FINISHERDOUBLE EDGE FINISHER

SOLID CARBIDE FINISHERSOLID CARBIDE FINISHER

SOLID CARBIDE SPIRALSOLID CARBIDE SPIRAL

SOLID CARBIDE STRAIGHTSOLID CARBIDE STRAIGHT

AcrylicsSeries 52-600 SC Double Edge Upcut ............... 3Series 57-600 SC Double Edge Downcut ........... 3Series 60-200 SC Three Edge Finisher ................. 3Series 60-470 SC Three Edge Finisher ................. 3Series 62-700 SC Single Edge Downcut ............. 4Series 62-800 SC Single Edge Downcut ............. 4Series 63-700 SC Single Edge Upcut ................. 4Series 63-800 SC Single Edge Upcut ................. 4

Hard PlasticsSeries 12-00 HSS Double Edge Straight ............ 5Series 48-600 CT Straight.................................. 5Series 56-000 SC Double Edge Straight .............. 5

Soft PlasticsSeries 10-00 HSS Single Edge O Flute ............... 6Series 11-00 HSS Single Edge O Flute ............... 6Series 56-600 SC Double Edge O Flute .............. 6Series 61-000 SC Single Edge O Flute................. 7Series 63-750 SC Single Edge Upcut ................. 7Series 63-850 SC Single Edge Upcut ................. 7Series 52-200 SC Double Edge Upcut ............... 8Series 62-750 SC Single Edge Downcut ............. 8Series 62-850 SC Single Edge Downcut ............. 8Series 66-300 SC Bottom Surfacing ................... 8

FoamSeries 12-00 HSS Double Edge Straight ............ 9Series 40-550 HSS Upcut Spiral ......................... 9Series 48-000 CT Double Edge Straight ............. 9

CompositesSeries 48-000 CT Single Edge Straight .............. 10Series 48-000 CT Double Edge Straight ............ 10Series 52-000 SC Double Edge Upcut .............. 11Series 57-000 SC Double Edge Downcut ......... 11Series 62-000 SC Single Edge Downcut ........... 11Series 63-000 SC Single Edge Upcut................. 11Series 58-000/55-000 Multi Edge Upcut ............. 12Series 59-000/54-000 Multi Edge Downcut ........ 12Series 67-000 SC Burrs ................................... 12Series 67-300 SC Double Edge Spirals .............. 12Series 56-000 SC Double Edge Straight Flute .... 13

Specialty ToolsSeries 16-50 SC Veining ............................... 13Series 27-00 SC Single Edge Flush Trim ........... 13Series 27-50 SC Double Edge Flush Trim ......... 13Series 28-20 SC Spiral Trim ............................ 14Series 28-50 CT Flush Trim.............................. 14Series 37-50 V-Bottom ................................. 14Series 38-50 Round Bottom .......................... 14Series 66-000 SC Edge Rounding..................... 15Series 66-200 SC Rout & Chamfer ................... 15Series 66-300 SC Bottom Surfacing ................. 15Series 70-100 CT Arbor Saws .......................... 16Series 70-200 SC Flush Saws............................ 16Series 70-300 CT Flush Saws ........................... 16Five Axis Tools ............................................... 17Series 33-30 Tool Extenders ........................... 17Series 33-40 Wrenches ................................ 17Series 33-50 Collets ..................................... 17Series 52-200B SC Ball Nose ............................. 17Series 52-200BL SC Extra Long Ball Nose ............. 17Air Rout Tools ............................................... 18Left Rotation Tools ......................................... 18Series 70-500 Plastic Drills ............................... 19Series 90-000 Spoilboard Cutters .................... 19

AccessoriesSeries 33-00 Fiber Bushings ........................... 19Series 34-00 Steel Bushings ........................... 19Series 33-10 Collet Brushes ........................... 20Series 33-21 Rust Free and T-9 ....................... 20Series 33-60 Taper Wipes .............................. 20Series 34-50 Collet Plugs .............................. 20

Important InformationPlastic Routing Tool Chart .................................. 1Van Niser Articles .............................................. 2

Feed and Speed Chart .............. Inside Back CoverGeneral Guidelines ................... Inside Back CoverNumerical Table of Contents ...... Inside Back Cover

All specifications subject to change without notice.

1

Onsrud Cutter

OnsrudCutter

Use the following charts as a guideline to select the appropriate tool series for Machining Plastics.

Plastic Routing Tool Chart

SOLID CARBIDE

Tool Series Acrylic Acrylic ABS Nylon PVC PVC Phenolic Poly- Poly- Poly- HDPE UHMW Fiberglass FoamCast Extruded Expanded Carbonate Ethlene Propylene

52/57-000 Pg 11 Pg 11

52-200 Pg 8 Pg 8 Pg 8 Pg 8

52/57-600 Pg 2 Pg 2 Pg 2 Pg 2 Pg 2 Pg 2 Pg 2

54/59-000 Pg 12 Pg 12

55/58-000 Pg 12 Pg 12

56-000 Pg 13 Pg 13 Pg 13

56-000 Pg 5 Pg 5 Pg 5 Pg 5 Pg 5 Pg 5 Pg 5 Pg 5 Pg 5

56-600 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6

60-200/470 Pg 3 Pg 3 Pg 3 Pg 3 Pg 3 Pg 3 Pg 3 Pg 3 Pg 3 Pg 3


62/63-000 Pg 11 Pg 11

62/63-700 Pg 4 Pg 4 Pg 4 Pg 4 Pg 4 Pg 4 Pg 4

62/63-750 Pg 7-8 Pg 7-8 Pg 7-8 Pg 7-8 Pg 7-8 Pg 7-8 Pg 7-8

62/63-800 Pg 4 Pg 4 Pg 4 Pg 4 Pg 4 Pg 4 Pg 4

62/63-850 Pg 7-8 Pg 7-8 Pg 7-8 Pg 7-8 Pg 7-8 Pg 7-8 Pg 7-8

66-300 Pg 8-15 Pg 8-15 Pg 8-15 Pg 8-15 Pg 8-15 Pg 8-15 Pg 8-15 Pg 8-15 Pg 8-15 Pg 8-15 Pg 8-15 Pg 8-15

67-000 Pg 12

67-300 Pg 12 Pg 12

SOLID CARBIDE

CARBIDE TIPPED


48-000 Pg 9-10 Pg 9-10 Pg 9-10

48-600 Pg 5 Pg 5 Pg 5

70-100 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16


70-300 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16 Pg 16

CARBIDE TIPPED

HIGH SPEED STEEL


10-00 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6

11-00 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6 Pg 6

12-00 Pg 5-9 Pg 5-9 Pg 5-9

40-550 Pg 9

HIGH SPEED STEEL

RecommendationsRecommendations

2

VAN NISER ARTICLE LIST

Log on to plasticrouting.comfor the latest in plastic routingdevelopments and technology.It's the best source on the netfor all your plastic routing needs,including in-depth and incisivearticles from Van Niser.

– Fixturing and Routing Plasticswith CNC Tooling

– Routing and Trimming PET

– Routing and Trimming ABS

– Routing and Trimming Polypropylene

– Frequently Asked Questions in the Routing of Plastics (#1)

– The Design of Plastic Cutting Tools

– Real World Routing Solutions - Part 1




– Preparing for Plastic Routing - Part 1

– Preparing for Plastic Routing - Part 2

– Routing and Trimming Acrylics

– Trimming Thermoformed Parts

– Premium Finishes when Routing Acrylic

– Frequently Asked Questionsin the Routing of Plastics (#2)

– Frequently Asked Questionsin the Routing of Plastics (#3)

– Cutting Tool Information for Plastics

– Reduce Routing Costs byGetting "Back to the Basics"

– Routing with Air

ACRYLICS

3

PART # CED CEL SHK DIA OAL52-622 1⁄4 3⁄8 1⁄4 21⁄252-624 1⁄4 3⁄4 1⁄4 21⁄252-638 3⁄8 1 3⁄8 352-650 1⁄2 11⁄8 1⁄2 31⁄2CED TOLERANCE +.000 - .004

For fast feed rates through harder more rigid plastics.

SOLID CARBIDE DOUBLE EDGE UPCUT SPIRAL

These tools aredesigned to cut

acrylic with asmooth finish andupward chip flow.

Usage:Acrylic,Nylon,

ABS,PE,Acetal,PET,HDPE,UHMW,

Polycarbonate

SERIES 52-600

PART # CED CEL SHK DIA OAL57-623 1⁄4 3⁄8 1⁄4 21⁄257-625 1⁄4 3⁄4 1⁄4 21⁄257-637 3⁄8 1 3⁄8 357-651 1⁄2 11⁄8 1⁄2 31⁄2CED TOLERANCE +.000 - .004

For a smooth finish

and downward chip flow in acrylics.

SOLID CARBIDE DOUBLE EDGE DOWNCUT SPIRAL

These tools aredesigned to

cut acrylic with a smooth finish

and downwardchip flow.

Usage:Acrylic, Nylon,

ABS, PE, Acetal,PET, HDPE, UHMW,

Polycarbonate

SERIES 57-600

PART # CED CEL SHK DIA OALUpcut60-243 3⁄8 5⁄8 3⁄8 360-245 3⁄8 11⁄8 3⁄8 360-249 1⁄2 11⁄8 1⁄2 31⁄260-253 1⁄2 15⁄8 1⁄2 460-251 1⁄2 21⁄8 1⁄2 41⁄260-269 3⁄4 15⁄8 3⁄4 460-271 3⁄4 21⁄8 3⁄4 5Downcut60-244 3⁄8 5⁄8 3⁄8 360-246 3⁄8 11⁄8 3⁄8 360-250 1⁄2 11⁄8 1⁄2 31⁄260-254 1⁄2 15⁄8 1⁄2 460-252 1⁄2 21⁄8 1⁄2 41⁄260-270 3⁄4 15⁄8 3⁄4 460-272 3⁄4 21⁄8 3⁄4 5CED TOLERANCE + .000 - .004

For perfect balance and smooth finish.

For perfect balance andsmooth finish.

SOLID CARBIDE THREE-EDGE FINISHER

Designed for perfect balanceand ultra smoothfinish over a wide

speed range.

Usage:Fiberglass, Phenolic,Acrylic, Nylon, PVC,

HDPE,Acetal, UHMW,Polycarbonate

SERIES 60-200

PART # CED CEL SHK DIA OALUpcut60-481 6 25 6 7660-471 8 25 8 7660-473 10 35 10 7660-475 12 35 12 8860-483 14 45 14 11060-477 16 55 16 12060-479 18 60 18 120Downcut60-482 6 25 6 7660-472 8 25 8 7660-474 10 35 10 7660-476 12 35 12 8860-484 14 45 14 11060-478 16 55 16 12060-480 18 60 18 120CED TOLERANCE +.000 - .004

SOLID CARBIDETHREE-EDGE FINISHER

METRICDesigned for ultrasmooth finish over a

wide variety ofspeed ranges.

Usage: Fiberglass, Phenolic,Acrylic, Nylon, PVC,

HDPE,Acetal, UHMW,Polycarbonate

SERIES 60-470

ACRYLICS

4

PART # CED CEL SHK DIA OAL63-802 2 8 2 5063-804 2 8 6 6463-806 2.5 8 2.5 5063-808 2.5 8 6 6463-810 3 8 3 5063-812 3 8 6 6463-814 3 12 3 6463-816 3 12 6 6463-818 4 8 4 6463-820 4 12 4 6463-822 4 20 4 6463-824 4 20 6 6463-826 4 30 4 6463-828 5 16 5 6463-830 5 16 6 6463-832 5 30 5 6463-834 6 8 6 6463-836 6 12 6 6463-838 6 20 6 6463-840 6 30 6 7663-842 6 38 6 7663-844 8 25 8 6463-846 8 38 8 7663-848 10 30 10 76CED TOLERANCE +.000 - .004

PART # CED CEL SHK DIA OAL63-700 1⁄16 1⁄4 1⁄4 263-701 1⁄16 1⁄4 1⁄8 263-710 1⁄8 1⁄4 1⁄4 263-711 1⁄8 1⁄4 1⁄8 263-712 1⁄8 1⁄2 1⁄4 263-713 1⁄8 1⁄2 1⁄8 263-715 5⁄32 9⁄16 1⁄4 263-716 3⁄16 3⁄8 3⁄16 263-717 3⁄16 3⁄8 1⁄4 263-718 3⁄16 5⁄8 1⁄4 263-719 3⁄16 5⁄8 3⁄16 263-720 7⁄32 3⁄4 1⁄4 21⁄263-724 1⁄4 3⁄8 1⁄4 263-725 1⁄4 3⁄4 1⁄4 21⁄263-726 1⁄4 11⁄4 1⁄4 363-733 3⁄8 11⁄8 3⁄8 3CED TOLERANCE +.000 - .004

For fast cuttingspiral O flute

geometry.

SOLID CARBIDESINGLE EDGE UPCUTSPIRAL O FLUTE

These single edgespiral O flute toolsprovide a smooth

finish in hard plasticswith upward

chip removal.

Usage:Acrylic,Nylon,PVC,

Polycarbonate

SERIES 63-700

For fast cutting spiral O flute

geometry.

SOLID CARBIDESINGLE EDGE UPCUT O FLUTE


finish in hard plasticswith upward chip

removal


Polycarbonate

SERIES 63-800

METRIC

PART # CED CEL SHK DIA OAL62-712 1⁄8 1⁄2 1⁄4 262-713 1⁄8 1⁄2 1⁄8 262-715 5⁄32 9⁄16 1⁄4 262-718 3⁄16 5⁄8 1⁄4 262-719 3⁄16 5⁄8 3⁄16 262-720 7⁄32 3⁄4 1⁄4 21⁄262-725 1⁄4 3⁄4 1⁄4 21⁄262-726 1⁄4 11⁄4 1⁄4 362-733 3⁄8 11⁄8 3⁄8 3CED TOLERANCE +.000 - .004


geometry.

SOLID CARBIDESINGLE EDGE DOWNCUTSPIRAL O FLUTE


finish in hard plasticswith downward

chip removal


Polycarbonate

SERIES 62-700

PART # CED CEL SHK DIA OAL62-802 2 8 2 5062-804 2 8 6 6462-806 2.5 8 2.5 5062-808 2.5 8 6 6462-810 3 8 3 5062-812 3 8 6 6462-814 3 12 3 6462-816 3 12 6 6462-818 4 8 4 6462-820 4 12 4 6462-822 4 20 4 6462-824 4 20 6 6462-826 4 30 4 6462-828 5 16 5 6462-830 5 16 6 6462-832 5 30 5 6462-834 6 8 6 6462-836 6 12 6 6462-838 6 20 6 6462-840 6 30 6 7662-842 6 38 6 7662-844 8 25 8 6462-846 8 38 8 7662-848 10 30 10 76CED TOLERANCE +.000 - .004


geometry.

SOLID CARBIDESINGLE EDGE DOWNCUT O FLUTE


finish in hard plasticswith downward

chip removal


Polycarbonate

SERIES 62-800

METRIC

HARD PLASTICS

5

PART # CED CEL SHK DIA OAL12-30 1⁄8 3⁄8 1⁄4 212-31 5⁄32 1⁄2 1⁄4 212-32 3⁄16 3⁄4 1⁄4 212-33 7⁄32 3⁄4 1⁄4 212-00 1⁄4 3⁄4 1⁄4 21⁄812-01 1⁄4 1 1⁄4 23⁄812-79* 1⁄4 1 1⁄4 31⁄412-35 1⁄4 1 1⁄2 21⁄212-37* 1⁄4 11⁄4 1⁄4 31⁄412-03 5⁄16 1 3⁄8 312-36 5⁄16 1 1⁄2 21⁄212-24 3⁄8 1 1⁄4 21⁄412-05 3⁄8 1 3⁄8 21⁄212-55* 3⁄8 1 3⁄8 31⁄212-06 3⁄8 1 1⁄2 21⁄212-26 3⁄8 11⁄4 1⁄2 31⁄412-08 7⁄16 11⁄4 1⁄2 23⁄412-09 1⁄2 1 1⁄4 21⁄412-10 1⁄2 11⁄4 1⁄2 23⁄412-11 1⁄2 11⁄2 1⁄2 31⁄212-51 1⁄2 2 1⁄2 412-12 9⁄16 11⁄4 1⁄2 23⁄412-25 5⁄8 3⁄4 1⁄4 21⁄812-13 5⁄8 11⁄4 1⁄2 23⁄412-27 3⁄4 1 1⁄4 21⁄412-14 3⁄4 11⁄4 1⁄2 23⁄412-16 7⁄8 11⁄4 1⁄2 23⁄412-17 1 11⁄4 1⁄2 23⁄412-18 11⁄8 11⁄4 1⁄2 23⁄412-19 11⁄4 11⁄4 1⁄2 23⁄4CED TOLERANCE ± .005 EXCEPT AS NOTED* THESE TOOLS ARE DESIGNED AND TOLERANCED FOR

AIR ROUTERS WITH GUIDE BUSHINGS. CED +.000 - .008

Forsmooth

finish.

HIGH SPEED STEELDOUBLE EDGEV FLUTE STRAIGHT

These double edgeV flutes are oftenselected when abalanced tool is

critical for smoothfinish. They are a

universal tool used in many environments.

Usage:Foam, Nylon

SERIES 12-00

For difficult to cut materials.

L = Left Rotation Tool

SOLID CARBIDE DOUBLE EDGESTRAIGHT

These carbidetools are designed

specifically to rout harder, more

rigid plastics.

Usage:Foam, Fiberglass,Phenolic, Acrylic,

Nylon, PVC,ABS, Acetal

SERIES 56-000

PART # CED CEL SHK DIA OAL56-041 1⁄8 1⁄4 1⁄4 256-061 3⁄16 3⁄8 1⁄4 256-062 3⁄16 5⁄8 1⁄4 256-062L 3⁄16 5⁄8 1⁄4 256-063* 3⁄16 5⁄8 1⁄4 456-081 1⁄4 3⁄8 1⁄4 21⁄256-082 1⁄4 3⁄4 1⁄4 21⁄256-082L 1⁄4 3⁄4 1⁄4 21⁄256-086* 1⁄4 11⁄4 1⁄4 456-121 3⁄8 5⁄8 3⁄8 21⁄256-122 3⁄8 7⁄8 3⁄8 21⁄256-122L 3⁄8 7⁄8 3⁄8 21⁄256-124* 3⁄8 15⁄8 3⁄8 656-162 1⁄2 1 1⁄2 356-162L 1⁄2 1 1⁄2 356-164 1⁄2 21⁄8 1⁄2 6CED TOLERANCE +.000 - .004*THESE TOOLS ARE DESIGNED AND TOLERANCED FOR AIRROUTERS WITH GUIDE BUSHINGS CED + .000 - .004

PART # CED CEL SHK DIA OALSingle Edge48-601 3⁄16 1⁄2 1⁄4 248-603 1⁄4 3⁄4 1⁄4 21⁄848-678* 1⁄4 3⁄4 1⁄4 31⁄448-605 1⁄4 1 1⁄4 23⁄848-607 3⁄8 1 3⁄8 21⁄248-635* 3⁄8 1 3⁄8 31⁄248-609 1⁄2 11⁄4 1⁄2 23⁄4

CED TOLERANCE ± .005 EXCEPT AS NOTED*THESE TOOLS ARE DESIGNED AND TOLERANCED FOR AIR ROUTERS WITH BEARINGS. CED +.000 - .006

For fast feed rates through harder more rigid plastics.

CARBIDE TIPPEDPLASTIC STRAIGHT

These carbidetipped tools are

designed specificallyfor cutting harder,

more rigid plastics.Single edge for

faster feed rates.Double edge for

smoother finish.

Usage:Fiberglass,

Phenolic, Nylon

SERIES 48-600

PART # CED CEL SHK DIA OALDouble Edge48-650 3⁄16 1⁄2 1⁄4 248-652 1⁄4 3⁄4 1⁄4 21⁄848-679* 1⁄4 3⁄4 1⁄4 31⁄448-654 1⁄4 1 1⁄4 23⁄848-656 3⁄8 1 3⁄8 21⁄248-636* 3⁄8 1 3⁄8 31⁄248-658 1⁄2 11⁄4 1⁄2 23⁄4

SOFT PLASTICS

6

PART # CED CEL SHK DIA OAL10-00 1⁄16 3⁄16 1⁄4 210-01 3⁄32 3⁄8 1⁄4 210-02 1⁄8 3⁄8 1⁄4 210-20 1⁄8 1⁄2 1⁄4 210-03 5⁄32 1⁄2 1⁄4 210-04 3⁄16 5⁄8 1⁄4 210-22 3⁄16 3⁄4 1⁄4 210-05 7⁄32 5⁄8 1⁄4 21⁄810-24 1⁄4 5⁄8 1⁄4 21⁄810-06 1⁄4 3⁄4 1⁄4 21⁄810-07 1⁄4 1 1⁄4 23⁄810-78 1⁄4 11⁄4 1⁄4 25⁄810-18 5⁄16 1 5⁄16 23⁄810-09 5⁄16 1 3⁄8 310-10 3⁄8 1 3⁄8 21⁄210-11 3⁄8 1 1⁄2 21⁄210-13 1⁄2 11⁄4 1⁄2 23⁄4CED TOLERANCE ± .005

For rapid feed rates

with optimum chip removal.

HIGH SPEED STEELSINGLE EDGEO FLUTE STRAIGHT

These tools combine an

open flute designwith single edge

geometry to provide optimum

chip removal at fast feed rates.

Usage:ABS, HDPE, PE,

PET, Polystyrene,Polypropylene, PVC

SERIES 10-00

PART # CED CEL SHK DIA OALSingle Edge11-01 1⁄8 1⁄2 1⁄4 211-75* 1⁄8 5⁄8 1⁄4 31⁄411-03 3⁄16 5⁄8 1⁄4 211-77* 3⁄16 3⁄4 1⁄4 31⁄411-05 1⁄4 3⁄4 1⁄4 21⁄811-71** 1⁄4 3⁄4 1⁄4 31⁄411-07 1⁄4 1 1⁄4 23⁄811-09 3⁄8 1 3⁄8 21⁄211-73** 3⁄8 1 3⁄8 31⁄211-11 1⁄2 11⁄4 1⁄2 23⁄4Double Edge11-00 3⁄16 5⁄8 1⁄4 211-02 1⁄4 3⁄4 1⁄4 21⁄811-72** 1⁄4 3⁄4 1⁄4 31⁄411-76** 1⁄4 3⁄4 1⁄4 33⁄411-04 1⁄4 1 1⁄4 23⁄811-78** 1⁄4 2 1⁄4 31⁄411-06 3⁄8 1 3⁄8 21⁄211-74** 3⁄8 1 3⁄8 31⁄211-10 1⁄2 11⁄4 1⁄2 23⁄4CED TOLERANCE ± .005 EXCEPT AS NOTED

* THESE TOOLS ARE DESIGNED AND TOLERANCED FOR AIR ROUTERS WITH GUIDE BUSHING.

**CED +.000 - .008 THESE TOOLS ARE DESIGNED ANDTOLERANCED FOR AIR ROUTERS WITH GUIDE BUSHING.

For cutting softer more

flexible plastics.

HIGH SPEED STEELPLASTIC O FLUTESTRAIGHT

These O flute toolsare designed for

cutting softer moreflexible plastics.Single edge for

faster feed rates.Double edge for

smoother finish.


PET, Polystyrene,Polypropylene, PVC

SERIES 11-00

CED TOLERANCE + .000 -.004

PART # CED CEL SHK DIA OAL56-626 1⁄4 1 1⁄4 31⁄456-628 1⁄4 11⁄4 1⁄4 456-638 3⁄8 7⁄8 3⁄8 21⁄256-639 3⁄8 1 3⁄8 456-650 1⁄2 1 1⁄2 356-652 1⁄2 1 1⁄2 456-654 1⁄2 13⁄4 1⁄2 456-655 1⁄2 21⁄8 1⁄2 6

For smooth finish in soft

flexible plastics.L = Left Rotation Tool

SOLID CARBIDEDOUBLE EDGE O FLUTE STRAIGHT

These tools aredesigned with free

cutting O flutegeometry along

with a double flute design for

smooth finish in softflexible plastics.

Usage:Polycarbonate, ABS,

HIPS, PET, PE,Polystyrene,

Polypropylene, PVC,Acetal, Acrylic,

HDPE, UHMW

SERIES 56-600

PART # CED CEL SHK DIA OAL56-610 1⁄8 5⁄16 1⁄4 256-612 1⁄8 1⁄2 1⁄4 256-614 1⁄8 5⁄8 1⁄4 456-616 3⁄16 3⁄8 1⁄4 256-618 3⁄16 5⁄8 1⁄4 256-620 3⁄16 1 1⁄4 456-624 1⁄4 3⁄8 1⁄4 21⁄256-625 1⁄4 1 1⁄4 21⁄256-625L 1⁄4 1 1⁄4 21⁄2

SOFT PLASTICS

7

For the fast free cutting

of O flute geometry.


SOLID CARBIDESINGLE EDGESTRAIGHT

These carbide toolsare designed to

combine the fastfree cutting of O

flute geometry withthe tool life avail-

able from solid car-bide particularly in

small diameters.


PET, Polystyrene,Polypropylene,

PVC, Acetal,Acrylic, UHMW,Polycarbonate

CED TOLERANCE

+.000 - .004

*THESE TOOLS ARE DESIGNED AND

TOLERANCED FOR AIR ROUTERS WITH

GUIDE BUSHINGS

SERIES 61-000

PART # CED CEL SHK DIA OAL61-041 1⁄8 5⁄16 1⁄4 261-042 1⁄8 1⁄2 1⁄4 261-042L 1⁄8 1⁄2 1⁄4 261-043 1⁄8 5⁄8 1⁄4 461-044 1⁄8 1⁄2 1⁄8 261-045 1⁄8 5⁄8 1⁄8 361-052 5⁄32 9⁄16 1⁄4 261-061 3⁄16 3⁄8 1⁄4 261-062 3⁄16 5⁄8 1⁄4 261-062L 3⁄16 5⁄8 1⁄4 261-063* 3⁄16 1 1⁄4 461-064 3⁄16 5⁄8 3⁄16 21⁄261-072 7⁄32 5⁄8 1⁄4 21⁄261-081 1⁄4 3⁄8 1⁄4 21⁄261-082 1⁄4 3⁄4 1⁄4 21⁄261-082L 1⁄4 3⁄4 1⁄4 21⁄261-083* 1⁄4 3⁄4 1⁄4 31⁄461-083L* 1⁄4 3⁄4 1⁄4 31⁄461-085* 1⁄4 1 1⁄4 31⁄461-084* 1⁄4 11⁄4 1⁄4 461-121 3⁄8 5⁄8 3⁄8 21⁄261-122 3⁄8 7⁄8 3⁄8 21⁄261-123* 3⁄8 15⁄8 3⁄8 661-162 1⁄2 1 1⁄2 361-164 1⁄2 15⁄8 1⁄2 461-166 1⁄2 21⁄8 1⁄2 6

PART # CED CEL SHK DIA OAL63-750 1⁄16 1⁄4 1⁄4 263-751 1⁄16 1⁄4 1⁄8 263-760 1⁄8 1⁄4 1⁄4 263-761 1⁄8 1⁄4 1⁄8 263-762 1⁄8 1⁄2 1⁄4 263-763 1⁄8 1⁄2 1⁄8 263-766 3⁄16 3⁄8 3⁄16 263-767 3⁄16 3⁄8 1⁄4 263-768 3⁄16 5⁄8 1⁄4 263-769 3⁄16 5⁄8 3⁄16 263-774 1⁄4 3⁄8 1⁄4 263-775 1⁄4 3⁄4 1⁄4 21⁄263-776 1⁄4 11⁄4 1⁄4 363-783 3⁄8 11⁄8 3⁄8 3CED TOLERANCE + .000 -.004


geometry.

SOLID CARBIDE SINGLE EDGE UPCUT SPIRAL O FLUTE


finish in plastics with upward

chip removal.

Usage:HDPE,HIPS,UHMW,

ABS,Polycarbonate,PE,Polystyrene,Polypropylene,

Acetal,Acrylic,PET

SERIES 63-750

PART # CED CEL SHK DIA OAL63-876 4 30 4 6463-878 5 16 5 6463-880 5 16 6 6463-882 5 30 5 6463-884 6 8 6 6463-886 6 12 6 6463-888 6 20 6 6463-890 6 30 6 7663-892 6 38 6 7663-894 8 25 8 6463-896 8 38 8 7663-898 10 30 10 76


geometry.

SOLID CARBIDESINGLE EDGE UPCUT O FLUTE


finish in plastics withupward chip

removal.



Acetal,Acrylic,PET

SERIES 63-850

PART # CED CEL SHK DIA OAL63-852 2 8 2 5063-854 2 8 6 6463-856 2.5 8 2.5 5063-858 2.5 8 6 6463-860 3 8 3 5063-862 3 8 6 6463-864 3 12 3 6463-866 3 12 6 6463-868 4 8 4 6463-870 4 12 4 6463-872 4 20 4 6463-874 4 20 6 64CED TOLERANCE + .000 -.004

METRIC

SOFT PLASTICS

8

PART # CED CEL SHK DIA OAL62-762 1⁄8 1⁄2 1⁄4 262-763 1⁄8 1⁄2 1⁄8 262-768 3⁄16 5⁄8 1⁄4 262-769 3⁄16 5⁄8 3⁄16 262-775 1⁄4 3⁄4 1⁄4 21⁄262-776 1⁄4 11⁄4 1⁄4 362-783 3⁄8 11⁄8 3⁄8 3CED TOLERANCE + .000 -.004

For fast cuttingspiral O flute

geometry.

SOLID CARBIDESINGLE EDGE DOWNCUT SPIRAL O FLUTE


finish in plasticswith downward

chip removal.

Usage:HDPE, HIPS, UHMW,

ABS, Polycarbonate,PE, Polystyrene,Polypropylene,

Acetal, Acrylic, PET

SERIES 62-750

PART # CED CEL SHK DIA OAL62-852 2 8 2 5062-854 2 8 6 6462-856 2.5 8 2.5 5062-858 2.5 8 6 6462-860 3 8 3 5062-862 3 8 6 6462-864 3 12 3 6462-866 3 12 6 6462-868 4 8 4 6462-870 4 12 4 6462-872 4 20 4 6462-874 4 20 6 6462-876 4 30 4 6462-878 5 16 5 6462-880 5 16 6 6462-882 5 30 5 6462-884 6 8 6 6462-886 6 12 6 6462-888 6 20 6 6462-890 6 30 6 7662-892 6 38 6 7662-894 8 25 8 6462-896 8 38 8 7662-898 10 30 10 76CED TOLERANCE + .000 -.004


geometry.

SOLID CARBIDESINGLE EDGE DOWNCUT O FLUTE


finish in plasticswith downward

chip removal



Acetal,Acrylic,PET

SERIES 62-850

METRIC

PART # CED CEL SHK DIA OAL52-360 1⁄2 11⁄8 1⁄2 352-362 1⁄2 11⁄4 1⁄2 31⁄252-365 1⁄2 15⁄8 1⁄2 31⁄252-365L 1⁄2 15⁄8 1⁄2 31⁄252-367 1⁄2 21⁄8 1⁄2 452-370 17⁄32 11⁄8 1⁄2 352-380 5⁄8 15⁄8 5⁄8 31⁄252-385 5⁄8 21⁄8 5⁄8 452-385L 5⁄8 21⁄8 5⁄8 452-390 3⁄4 15⁄8 3⁄4 452-395 3⁄4 21⁄8 3⁄4 452-395L 3⁄4 21⁄8 3⁄4 4CED TOLERANCE + .000 - .004

For upwardchip removal.L = Left Rotation Tool

SOLID CARBIDE DOUBLE EDGE UPCUT SPIRAL ROUT

Particularly usefulfor cutting thicker

sheets of softplastic and foam

Usage:Polypropylene,

HDPE, UHMW

SERIES 52-200

SOLID CARBIDE DOUBLEEDGE BOTTOM SURFACE

These tools are designed for pocketing

applications wherethe bottom of the

pocket must besmooth with

radiused corners.Particularly useful insoft plastics,acrylic,

and aluminum

Usage:Decorative and

Specialty

For extrasmooth

pockets.

SERIES 66-300

PART # CED CEL SHK DIA OAL66-306 1⁄8 1⁄4 1⁄8 266-308 1⁄8 1⁄4 1⁄4 266-314 1⁄4 3⁄8 1⁄4 266-320 3⁄8 5⁄8 3⁄8 21⁄266-326 1⁄2 7⁄8 1⁄2 3CED TOLERANCE + .000 - .004

NEW

CARBIDE TIPPED DOUBLE EDGE STRAIGHT

The carbide tippedtools are designedfor general usage

where superior balance and vibration free

cutting provides a smoother

finish along withlong tool life.

Usage:Foam, Fiberglass,

Phenolic

SERIES 48-000

PART # CED CEL SHK DIA OAL48-008+ 1⁄8 5⁄16 1⁄4 248-000 3⁄16 1⁄2 1⁄4 248-002 7⁄32 5⁄8 1⁄4 248-004 1⁄4 5⁄8 1⁄4 21⁄848-006 1⁄4 7/8 1⁄4 23⁄848-018 1⁄4 7/8 1⁄2 21⁄248-106 1⁄4 1 1⁄4 23⁄848-179* 1⁄4 1 1⁄4 31⁄448-011 5⁄16 3⁄4 3⁄8 21⁄248-017 5⁄16 3⁄4 1⁄2 21⁄448-010 5⁄16 1 1⁄4 21⁄248-122 5⁄16 1 5⁄16 21⁄248-012 3⁄8 3⁄4 1⁄4 21⁄448-154 3⁄8 3⁄4 1⁄2 21⁄248-013 3⁄8 1 1⁄4 23⁄848-036** 3⁄8 1 3⁄8 21⁄248-057 3⁄8 1 1⁄2 21⁄248-058* 3⁄8 11⁄4 3⁄8 348-158 3⁄8 11⁄4 1⁄2 23⁄448-059 7⁄16 11⁄4 1⁄2 23⁄448-014 1⁄2 3⁄4 1⁄4 21⁄848-072 1⁄2 1 1⁄2 21⁄248-114 1⁄2 1 1⁄4 21⁄448-044 1⁄2 11⁄4 3⁄8 23⁄448-076 1⁄2 11⁄4 1⁄2 23⁄448-080 1⁄2 11⁄2 1⁄2 348-081 1⁄2 2 1⁄2 448-181 1⁄2 21⁄4 1⁄2 41⁄448-183 1⁄2 21⁄2 1⁄2 41⁄248-083 17⁄32 11⁄4 1⁄2 23⁄448-182 9⁄16 1 1⁄4 23⁄848-082 9⁄16 11⁄4 1⁄2 23⁄448-015 5⁄8 1 1⁄4 21⁄448-086 5⁄8 11⁄4 1⁄2 23⁄448-187 11⁄16 1 1⁄4 23⁄848-087 11⁄16 11⁄4 1⁄2 23⁄448-016 3⁄4 1 1⁄4 21⁄448-088 3⁄4 11⁄4 1⁄2 348-089 3⁄4 11⁄2 1⁄2 348-215 3⁄4 2 3⁄4 4See Page 10 for Complete Series and Tolerances

+ Solid Carbide

* CED +.000-.006 THESE TOOLS ARE DESIGNED

**CED ± .005 THESE TOOLS ARE DESIGNEDAND TOLERANCED FOR AIR ROUTERS WITH ANDTOLERANCED FOR AIR ROUTERS GUIDE BUSHING.WITH GUIDE BUSHING.

FOAM

9

These 4-flute spiraltools are designed

to cut thicker pieces of foam with

upward chipflow

Usage:Foam

PART # CED CEL SHK DIA OAL40-562 1⁄2 35⁄8 1⁄2 640-564 1⁄2 41⁄8 1⁄2 61⁄2CED TOLERANCE + .000 - .010

For deep cuts in foam.

HIGH SPEED STEELUPCUTSPIRAL

SERIES 40-550

PART # CED CEL SHK DIA OAL12-30 1⁄8 3⁄8 1⁄4 212-31 5⁄32 1⁄2 1⁄4 212-32 3⁄16 3⁄4 1⁄4 212-33 7⁄32 3⁄4 1⁄4 212-00 1⁄4 3⁄4 1⁄4 21⁄812-01 1⁄4 1 1⁄4 23⁄812-79* 1⁄4 1 1⁄4 31⁄412-35 1⁄4 1 1⁄2 21⁄212-37* 1⁄4 11⁄4 1⁄4 31⁄412-03 5⁄16 1 3⁄8 312-36 5⁄16 1 1⁄2 21⁄212-24 3⁄8 1 1⁄4 21⁄412-05 3⁄8 1 3⁄8 21⁄212-55* 3⁄8 1 3⁄8 31⁄212-06 3⁄8 1 1⁄2 21⁄212-26 3⁄8 11⁄4 1⁄2 31⁄412-08 7⁄16 11⁄4 1⁄2 23⁄412-09 1⁄2 1 1⁄4 21⁄412-10 1⁄2 11⁄4 1⁄2 23⁄412-11 1⁄2 11⁄2 1⁄2 31⁄212-51 1⁄2 2 1⁄2 412-12 9⁄16 11⁄4 1⁄2 23⁄412-25 5⁄8 3⁄4 1⁄4 21⁄812-13 5⁄8 11⁄4 1⁄2 23⁄412-27 3⁄4 1 1⁄4 21⁄412-14 3⁄4 11⁄4 1⁄2 23⁄412-16 7⁄8 11⁄4 1⁄2 23⁄412-17 1 11⁄4 1⁄2 23⁄412-18 11⁄8 11⁄4 1⁄2 23⁄412-19 11⁄4 11⁄4 1⁄2 23⁄4

Forsmooth

finish.


These double edgeV flutes are oftenselected when abalanced tool is

critical for smoothfinish. They are a

universal tool used in many environments.

Usage:Foam, Nylon

CED TOLERANCE ± .005EXCEPT AS NOTED* THESE TOOLS ARE

DESIGNED ANDTOLERANCED FOR

AIR ROUTERS WITHGUIDE BUSHINGS.

CED +.000 - .008

SERIES 12-00

COMPOSITES

10

PART # CED CEL SHK DIA OAL48-183 1⁄2 21⁄2 1⁄2 41⁄248-083 17⁄32 11⁄4 1⁄2 23⁄448-182 9⁄16 1 1⁄4 23⁄848-082 9⁄16 11⁄4 1⁄2 23⁄448-015 5⁄8 1 1⁄4 21⁄448-086 5⁄8 11⁄4 1⁄2 23⁄448-187 11⁄16 1 1⁄4 23⁄848-087 11⁄16 11⁄4 1⁄2 23⁄448-016 3⁄4 1 1⁄4 21⁄448-088 3⁄4 11⁄4 1⁄2 348-089 3⁄4 11⁄2 1⁄2 348-215 3⁄4 2 3⁄4 448-189 25⁄32 11⁄4 1⁄2 23⁄448-090 13⁄16 11⁄4 1⁄2 23⁄448-096 7⁄8 11⁄4 1⁄2 23⁄448-115 15⁄16 11⁄4 1⁄2 23⁄448-100 1 11⁄4 1⁄2 23⁄448-250 1 2 3⁄4 448-120 11⁄8 11⁄4 1⁄2 23⁄448-150 11⁄4 11⁄4 1⁄2 23⁄448-156 13⁄8 11⁄4 1⁄2 23⁄448-160 11⁄2 11⁄4 1⁄2 23⁄448-170 15⁄8 11⁄4 1⁄2 23⁄448-180 13⁄4 11⁄4 1⁄2 23⁄448-200 2 11⁄4 1⁄2 23⁄4

CED TOLERANCE ± .005 EXEPT AS NOTED

* CED +.000-.006 THESE TOOLS ARE DESIGNED AND TOLERANCED

FOR AIR ROUTERS WITH GUIDE BUSHING.

**CED ± .005 THESE TOOLS ARE DESIGNED AND TOLERANCED FOR

AIR ROUTERS WITH GUIDE BUSHING.

For general usage and

balance.

CARBIDE TIPPED DOUBLE EDGE STRAIGHT

The carbide tippedtools are designedfor general usage

where superior balance and vibration free

cutting provides a smoother

finish along withlong tool life.


Phenolic

SERIES 48-000

PART # CED CEL SHK DIA OAL48-008+ 1⁄8 5⁄16 1⁄4 248-000 3⁄16 1⁄2 1⁄4 248-002 7⁄32 5⁄8 1⁄4 248-004 1⁄4 5⁄8 1⁄4 21⁄848-006 1⁄4 7/8 1⁄4 23⁄848-018 1⁄4 7/8 1⁄2 21⁄248-106 1⁄4 1 1⁄4 23⁄848-179* 1⁄4 1 1⁄4 31⁄448-011 5⁄16 3⁄4 3⁄8 21⁄248-017 5⁄16 3⁄4 1⁄2 21⁄448-010 5⁄16 1 1⁄4 21⁄248-122 5⁄16 1 5⁄16 21⁄248-012 3⁄8 3⁄4 1⁄4 21⁄448-154 3⁄8 3⁄4 1⁄2 21⁄248-013 3⁄8 1 1⁄4 23⁄848-036** 3⁄8 1 3⁄8 21⁄248-057 3⁄8 1 1⁄2 21⁄248-058* 3⁄8 11⁄4 3⁄8 348-158 3⁄8 11⁄4 1⁄2 23⁄448-059 7⁄16 11⁄4 1⁄2 23⁄448-014 1⁄2 3⁄4 1⁄4 21⁄848-072 1⁄2 1 1⁄2 21⁄248-114 1⁄2 1 1⁄4 21⁄448-044 1⁄2 11⁄4 3⁄8 23⁄448-076 1⁄2 11⁄4 1⁄2 23⁄448-080 1⁄2 11⁄2 1⁄2 348-081 1⁄2 2 1⁄2 448-181 1⁄2 21⁄4 1⁄2 41⁄4

+ Solid Carbide

CED TOLERANCE ± .005 EXEPT AS NOTED

* CED +.000-.006 THESE TOOLS ARE DESIGNED ** CED ± .005 THESE TOOLS ARE DESIGNEDAND TOLERANCED FOR AIR ROUTERS WITH AND TOLERANCED FOR AIR ROUTERSGUIDE BUSHING. WITH GUIDE BUSHING.

PART # CED CEL SHK DIA OAL48-055 3⁄8 1 1⁄2 21⁄248-155* 3⁄8 11⁄4 3⁄8 348-056 3⁄8 11⁄4 1⁄2 23⁄448-061 1⁄2 1 1⁄2 21⁄248-065 1⁄2 11⁄4 1⁄2 23⁄448-069 1⁄2 11⁄2 1⁄2 348-084 1⁄2 11⁄2 1⁄2 448-070 1⁄2 2 1⁄2 448-075 1⁄2 2 1⁄2 548-071 1⁄2 21⁄4 1⁄2 41⁄4

For fast feed rates with freer cutting action.

CARBIDE TIPPEDSINGLE EDGESTRAIGHT

These carbidetipped tools are

designed for general usage

where faster feedrates, freer cutting

action and longtool life are essential.


Phenolic

SERIES 48-000

PART # CED CEL SHK DIA OAL48-003 3⁄16 1⁄2 1⁄4 248-001 7⁄32 5⁄8 1⁄4 248-030 1⁄4 3⁄4 1⁄2 21⁄248-005 1⁄4 7⁄8 1⁄4 23⁄848-031 1⁄4 1 1⁄2 21⁄248-007 1⁄4 1 1⁄4 23⁄848-079* 1⁄4 1 1⁄4 31⁄448-073 9⁄32 3⁄4 1⁄4 21⁄848-022 5⁄16 1 5⁄16 21⁄248-153 5⁄16 1 1⁄2 21⁄448-034** 3⁄8 1 3⁄8 21⁄2

COMPOSITES

11

PART # CED CEL SHK DIA OAL62-040 1⁄8 1⁄2 1⁄4 262-080 1⁄4 3⁄4 1⁄4 21⁄262-100 5⁄16 13⁄16 3⁄8 21⁄262-120 3⁄8 7⁄8 3⁄8 21⁄2CED TOLERANCE ± .000 - .004

For extremelyfast feed

rates at smalldiameters.

SOLID CARBIDE SINGLE EDGE DOWNCUT SPIRAL

These carbide toolsare good general

purpose plastic toolsand hold up well inboth soft and hard

or abrasive plastics.

Usage:Fiberglass,

Phenolic, Acetal

SERIES 62-000

PART # CED CEL SHK DIA OAL63-040 1⁄8 1⁄2 1⁄4 263-050 5⁄32 9⁄16 1⁄4 263-060 3⁄16 5⁄8 1⁄4 263-070 7⁄32 5⁄8 1⁄4 21⁄263-080 1⁄4 3⁄4 1⁄4 21⁄263-090 9⁄32 3⁄4 3⁄8 21⁄263-100 5⁄16 13⁄16 3⁄8 21⁄263-120 3⁄8 7⁄8 3⁄8 21⁄263-140 7⁄16 1 1⁄2 363-160 1⁄2 1 1⁄2 3CED TOLERANCE + .000 - .004

For abrasive

materials.

SOLID CARBIDE SINGLE EDGE UPCUT SPIRAL

These carbide toolsare designed to

replace high speedsteel spirals when

the material cut istoo abrasive for

steel or when thefeed rates are toohigh for steel. Theyare often used in

slotting or blind routing situations

Usage:Fiberglass,

Phenolic, Acetal

SERIES 63-000

PART # CED CEL SHK DIA OAL52-040 1⁄8 1⁄2 1⁄4 252-050 5⁄32 9⁄16 1⁄4 252-060 3⁄16 5⁄8 1⁄4 252-060L 3⁄16 5⁄8 1⁄4 252-070 7⁄32 5⁄8 1⁄4 21⁄252-080 1⁄4 3⁄4 1⁄4 21⁄252-080L 1⁄4 3⁄4 1⁄4 21⁄252-090 9⁄32 3⁄4 3⁄8 21⁄252-100 5⁄16 13⁄16 3⁄8 21⁄252-120 3⁄8 7⁄8 3⁄8 21⁄252-140 7⁄16 1 1⁄2 352-160 1⁄2 1 1⁄2 3CED TOLERANCE + .000 - .004

For upcut chip flow.


SOLID CARBIDE DOUBLE EDGE UPCUT SPIRAL

These carbide toolsare designed as a

general purpose spiral with several

times the life of theirhigh speed steel

counterparts. Theyare used when

upward chip flow is preferred.

Usage:Fiberglass,

Phenolic, Acetal

SERIES 52-000

PART # CED CEL SHK DIA OAL57-040 1⁄8 1⁄2 1⁄4 257-050 5⁄32 9⁄16 1⁄4 257-060 3⁄16 5⁄8 1⁄4 257-070 7⁄32 5⁄8 1⁄4 21⁄257-080 1⁄4 3⁄4 1⁄4 21⁄257-090 9⁄32 3⁄4 3⁄8 21⁄257-100 5⁄16 13⁄16 3⁄8 21⁄257-120 3⁄8 7⁄8 3⁄8 21⁄257-140 7⁄16 1 1⁄2 357-160 1⁄2 1 1⁄2 3CED TOLERANCE ± .000 - .004

For downcutchip flow.

SOLID CARBIDEDOUBLE EDGEDOWNCUT SPIRAL

These carbide toolsare designed as

a general purposespiral with several

times the life of their high speed

counterparts. Theyare used when a

downward chipflowaction is preferred.

Usage:Fiberglass,

Phenolic, Acetal

SERIES 57-000

COMPOSITES

12

PART # CED CEL SHK DIA OALThree Edge59-040 1⁄8 1⁄2 1⁄4 259-060 3⁄16 5⁄8 1⁄4 259-080 1⁄4 3⁄4 1⁄4 21⁄2Four Edge54-040 1⁄8 1⁄2 1⁄4 254-050 5⁄32 9⁄16 1⁄4 254-060 3⁄16 5⁄8 1⁄4 254-080 1⁄4 3⁄4 1⁄4 21⁄2CED TOLERANCE ± .000 - .004

For use when horsepower

and spindle speedmay be a problem.

SOLID CARBIDEMULTIPLE EDGEDOWNCUT SPIRAL

These multiple flutecarbide tools aredesigned to rout

difficult to cut material whenhorsepower or

spindle speed maybe a problem.These

tools employ downcut router

geometry to holdmaterial and force

chips down whilerouting through the

piece part.

Usage:Fiberglass, Phenolic

SERIES 59-000/ 54-000

PART # CED CEL SHK DIA OALThree Edge58-040 1⁄8 1⁄2 1⁄4 258-060 3⁄16 5⁄8 1⁄4 258-080 1⁄4 3⁄4 1⁄4 21⁄2Four Edge55-040 1⁄8 1⁄2 1⁄4 255-050 5⁄32 9⁄16 1⁄4 255-060 3⁄16 5⁄8 1⁄4 255-080 1⁄4 3⁄4 1⁄4 21⁄2CED TOLERANCE + .000 - .004

For difficult tocut materials.

SOLID CARBIDEMULTIPLE EDGE UPCUT SPIRAL

These multiple flutecarbide tools aredesigned to rout

difficult to cut material whenhorsepower or

spindle speed maybe a problem.They

employ upcut routerrather than end millgeometry for better

chip removal andsmoother finish.

Primary Usage:Fiberglass, Phenolic

SERIES 58-000/ 55-000

PART # CED CEL SHK DIA OAL67-080 1⁄4 3⁄4 1⁄4 21⁄267-082 1⁄4 3⁄4 1⁄4 21⁄2 2 Flutes

67-084 1⁄4 3⁄4 1⁄4 21⁄2 Aramid Tool

67-120 3⁄8 7⁄8 3⁄8 21⁄267-122 3⁄8 7⁄8 3⁄8 21⁄2 2 Flutes

67-124 3⁄8 7⁄8 3⁄8 21⁄2 Aramid Tool

67-160 1⁄2 1 1⁄2 367-162 1⁄2 1 1⁄2 3 2 Flutes

67-164 1⁄2 1 1⁄2 3 Aramid Tool

For fibrous materials.

SOLID CARBIDE FIBERGLASS ROUTER

These carbidetools are designed

as fiberglass routers.Their upcut/down-

cut diamond designeffectively shearsfibrous materials.

Certain tools in the line have been further developed

to cut aramid fiber composites.

Primary Usage:Fiberglass,

Phenolic,Aramid

SERIES 67-000

PART # CED CEL SHK DIA OALUpcut

67-305 3⁄8 11⁄8 3⁄8 367-313 1⁄2 15⁄8 1⁄2 31⁄267-315 1⁄2 21⁄4 1⁄2 4Downcut67-306 3⁄8 11⁄8 3⁄8 367-314 1⁄2 15⁄8 1⁄2 31⁄267-316 1⁄2 21⁄4 1⁄2 4CED TOLERANCE + .000 - .004

For fast feeds at

9,000 RPM

SOLID CARBIDE FIBERGLASSRAPID ROUTER

These two flute carbide tools with

spiral chipbreakerscut fibrous materials

at fast feed rates.

Usage:Fiberglass,

Phenolic

SERIES 67-300

PART# CED CEL SHK DIA OAL STYLE27-00 1⁄4 1⁄4 1⁄4 11⁄2 Flush

27-01 1⁄4 1⁄4 1⁄4 11⁄2 7° Bevel

27-02 1⁄4 1⁄4 1⁄4 11⁄2 Boring Pt.

27-03 1⁄4 3⁄8 1⁄4 2 Flush

27-04 1⁄4 3⁄8 1⁄4 11⁄2 10° Bevel& Flush

CED TOLERANCE + .000 - .010

For trimmingcounter tops.

Available withboring point.

SOLID CARBIDESINGLE EDGELAMINATE TRIM

These single edgetools are designed

to trim counter tops.The pilot bearson the finished

surface and acts as a guide to trim

flush or with a bevel. Available

with boring point if necessary to

plunge and rout.

Usage:Trimming laminatecounter tops and

trimmingplastic parts

SERIES 27-00

SPECIALTY TOOLS

13

PART # CED CEL SHK DIA OAL56-040 1⁄8 1⁄2 1⁄4 256-050 5⁄32 9⁄16 1⁄4 256-060 3⁄16 5⁄8 1⁄4 256-070 7⁄32 5⁄8 1⁄4 21⁄256-080 1⁄4 3⁄4 1⁄4 21⁄256-084* 1⁄4 3⁄4 1⁄4 31⁄456-090 9⁄32 3⁄4 3⁄8 21⁄256-100 5⁄16 13⁄16 3⁄8 21⁄256-120 3⁄8 7⁄8 3⁄8 21⁄256-140 7⁄16 1 1⁄2 356-160 1⁄2 1 1⁄2 3CED TOLERANCE +.000 - .004

For difficult to cut materials.

SOLID CARBIDE DOUBLE EDGESTRAIGHT

These carbide toolsare designed as a

general purpose toolto rout difficult to

cut materials particularly in small

diameters.Usage:

Fiberglass, Phenolic

*THESE TOOLS ARE DESIGNED AND

TOLERANCED FOR AIRROUTERS WITH

GUIDE BUSHINGS

SERIES 56-000

PART # SM DIA CEL SHK DIA OAL16-50 1⁄16 1⁄4 1⁄4 11⁄216-51 3⁄32 1⁄4 1⁄4 11⁄216-52 1⁄8 1⁄4 1⁄4 11⁄2

For decorativecuts in all types

of materials.

SOLID CARBIDE VEINING

These single edgetapered flute tools

are designed tomake decorativecuts in all types of

materials and provide long

cutter life.


Specialty

SERIES 16-50

PART# CED CEL SHK DIA OAL STYLE27-51 1⁄4 1⁄4 1⁄4 15⁄8 7° Bevel

27-50 1⁄4 7⁄16 1⁄4 15⁄8 Flush

CED TOLERANCE + .000 - .010

For a satin smooth finish

when trimming laminate

counter tops.

SOLID CARBIDEDOUBLE EDGELAMINATE TRIM

These double edgetools with a pilotare designed to

give a satin smoothfinish when trimming

laminate coutertops. They are

available asflush trim or

bevel trim bits.

Usage:Trimming laminatecounter tops and

trimmingplastic parts

SERIES 27-50

COMPOSITES

SPECIALTY TOOLS

14

PART# CED CEL SHK DIA OAL FLUTES Rep. Bearing Kit28-55 1⁄4 1 1⁄4 21⁄2 2 N/A28-50 3⁄8 1 1⁄4 23⁄4 2 N/A28-51 3⁄8 1⁄2 1⁄4 21⁄4 2 N/A28-66 3⁄8 1⁄2 1⁄4 21⁄4 3⁄16 Overhang N/A28-52 1⁄2 1 1⁄4 23⁄4 2 28-7628-53 1⁄2 1⁄2 1⁄4 2 2 28-7628-54 1⁄2 1 1⁄2 31⁄4 2 28-7628-56 1⁄2 1 3⁄8 3 2 28-7628-57 1⁄2 1 1⁄4 23⁄4 3 28-7628-59 1⁄2 11⁄2 1⁄2 41⁄4 3 28-7628-63 1⁄2 11⁄2 1⁄2 41⁄4 2 28-7628-64 1⁄2 2 1⁄2 41⁄4 2 28-7628-67 1⁄2 3⁄8 1⁄4 21⁄4 Flush/22° N/ACED TOLERANCE + .000 - .015

28-76 Replacement Bearing Kit

For a smooth finished edge ondense, abrasive and laminated

materials.

For trimming stacked sheets

of plastic.

CARBIDE TIPPEDFLUSH TRIM

These two and three flutetools are designed toprovide a smooth finishededge on dense,abrasiveand laminated materials.A ball bearing guideassists free cutting action.

Usage:Laminates, plastics

SERIES 28-50

PART # CED CEL SHK DIA OALSolid Carbide37-50 3⁄16 5⁄8 1⁄4 237-51 1⁄4 3⁄4 1⁄4 237-52 3⁄8 3⁄4 3⁄8 21⁄2CED TOLERANCE + .000 – .005

Carbide Tipped37-60 3⁄8 19⁄32 1⁄4 111⁄16

37-61 1⁄2 13⁄32 1⁄4 125⁄32

37-62 3⁄4 1⁄2 1⁄2 21⁄837-63 1 27⁄32 1⁄2 227⁄32

CED TOLERANCE ± .005

For V groovingnon abrasive

plastics.

CARBIDEV BOTTOM

These two flute toolsare designed for

V grooving or beveling plastics.


Specialty

SERIES 37-50

PART # CED CEL SHK DIA OALSolid Carbide38-50 1⁄8 3⁄8 1⁄4 238-51 3⁄16 5⁄8 1⁄4 238-52* 1⁄4 3⁄4 1⁄4 238-53* 3⁄8 3⁄4 3⁄8 21⁄4Carbide Tipped38-60 3⁄8 5⁄16 1⁄4 121⁄32

38-61 1⁄2 13⁄32 1⁄4 125⁄32

38-62 5⁄8 17⁄32 1⁄4 129⁄32

38-63 3⁄4 5⁄8 1⁄4 21⁄16

CED TOLERANCE ± .005

*CED TOLERANCE + .000 – .004

For grooving or face cutting

plastics.

CARBIDEROUND BOTTOM

These two flute toolsare designed with constant radii per

diameter shown forgrooving or face

cutting plastics.


Specialty

SERIES 38-50

PART# CED CEL SHK DIA OAL FLUTE

28-20 1⁄4 3⁄4 1⁄4 3 228-25 1⁄2 11⁄8 1⁄2 4 228-30* 1⁄2 11⁄8 1⁄2 4 3CED TOLERANCE + .000 -.004* Up/Down Compression Spiral

REPLACEMENT BEARING KITS FOR SERIES 28-20 Solid Carbide Double Bearing Plastic Trim Tool Kits28-89 KIT for 28-20 Tool28-88 KIT for 28-25 Tool28-88 KIT for 28-30 Tool

SOLID CARBIDEDOUBLE-BEARINGPLASTIC TRIM

These upcut spiralsare designed to trim

stacked sheets ofplastic. They use a

double bearingguide to ensuresmooth cuttingaction around

a template.

Usage:Trimming stackedsheets plastic and

laminates

SERIES 28-20

These two and threeflute tools are

designed to providea smooth finished

edge on dense,abrasive and

laminated materials.A ball bearing guide

assists free cuttingaction.

Usage:Laminates, plastics

SPECIALTY TOOLS

15

PART# CED CEL SHK DIA OAL OPENING RADIUS SM CED TIP TO RAD PLASTIC SIZE

Single Edge O66-082 1⁄4 3⁄8 1⁄4 21⁄2 5⁄32 1⁄8 .195 1⁄16 1⁄866-083 1⁄4 3⁄8 1⁄4 21⁄2 7⁄32 3⁄16 .180 1⁄16 3⁄16

66-084 1⁄4 3⁄8 1⁄4 21⁄2 9⁄32 1⁄4 .163 1⁄16 1⁄4Single Edge Spiral O66-085 1⁄4 3⁄8 1⁄4 21⁄2 5⁄32 1⁄8 .195 1⁄16 1⁄866-086 1⁄4 3⁄8 1⁄4 21⁄2 7⁄32 3⁄16 .180 1⁄16 3⁄16

66-087 1⁄4 3⁄8 1⁄4 21⁄2 9⁄32 1⁄4 .163 1⁄16 1⁄4Double Edge O66-092 1⁄4 3⁄8 1⁄4 21⁄2 5⁄32 1⁄8 .195 1⁄16 1⁄866-093 1⁄4 3⁄8 1⁄4 21⁄2 7⁄32 3⁄16 .180 1⁄16 3⁄16

66-094 1⁄4 3⁄8 1⁄4 21⁄2 9⁄32 1⁄4 .163 1⁄16 1⁄4Double Edge V66-120 3⁄8 3⁄8 3⁄8 21⁄2 5⁄32 1⁄8 .320 1⁄16 1⁄866-121 3⁄8 3⁄8 3⁄8 21⁄2 7⁄32 3⁄16 .305 1⁄16 3⁄16

66-122 3⁄8 3⁄8 3⁄8 21⁄2 9⁄32 1⁄4 .288 1⁄16 1⁄466-123 3⁄8 1⁄2 3⁄8 21⁄2 13⁄32 3⁄8 .255 1⁄16 3⁄866-160 1⁄2 3⁄8 1⁄2 3 5⁄32 1⁄8 .445 1⁄16 1⁄866-161 1⁄2 3⁄8 1⁄2 3 7⁄32 3⁄16 .430 1⁄16 3⁄16

66-162 1⁄2 3⁄8 1⁄2 3 9⁄32 1⁄4 .413 1⁄16 1⁄466-163 1⁄2 5⁄8 1⁄2 3 17⁄32 1⁄2 .347 1⁄16 1⁄2CED TOLERANCE + .000 -.004

For roundingthe edgeof plastic.

SOLID CARBIDEEDGE ROUNDING

These solid carbidetools are designed

for rounding theedge of plasticsheets or parts.

They come in both single edge

and double edge.


Specialty

SERIES 66-000

PART # CED CEL SHK DIA OAL MAT'LTHICKNESS

66-200 1⁄4 1⁄8 3⁄8 21⁄2 1⁄866-202 3⁄8 1⁄8 1⁄2 3 1⁄866-204 1⁄4 3⁄16 3⁄8 21⁄2 3⁄16

66-206 3⁄8 3⁄16 1⁄2 3 3⁄16

66-208 1⁄4 1⁄4 3⁄8 21⁄2 1⁄466-210 3⁄8 1⁄4 1⁄2 3 1⁄4CED TOLERANCE + .000 -.004

For specialtyedge finishing.

SOLID CARBIDEROUT AND CHAMFER

These solid carbidetools are designed to

provide up to a 1⁄16"top face chamfer

and a finished sideedge on plasticsheets or parts.

Usage: Decorative and

Specialty

SERIES 66-200

PART # CED CEL SHK DIA OAL66-306 1⁄8 1⁄4 1⁄8 266-308 1⁄8 1⁄4 1⁄4 266-314 1⁄4 3⁄8 1⁄4 266-320 3⁄8 5⁄8 3⁄8 21⁄266-326 1⁄2 7⁄8 1⁄2 3CED TOLERANCE + .000 -.004

For extrasmooth

pockets.

SOLID CARBIDEDOUBLE EDGEBOTTOM SURFACING

These tools aredesigned for

pocketing applications where

the bottom of thepocket must be

smooth with radiusedcorners. Particularly

useful in soft plastics,acrylic, and

aluminum.Usage:

Decorative andSpecialty

SERIES 66-300

SPECIALTY TOOLS

16

CARBIDE TIPPED SAW AND ARBOR

These carbidetipped saws aredesigned to trim

and groove bothhard and soft

plastics. These sawsrun in conjunction

with the saw arbors.Saws are reversible

for right or left handrotation cutting.

SERIES 70-100

PART # CED TEETH RAKE KERF GRIND70-100 2 10 0° .095 TCG70-102 21⁄2 10 0° .095 TCG70-104 3 10 0° .095 TCG70-106 31⁄2 10 0° .095 TCG70-108 4 10 0° .095 TCG

Soft Plastic - Slow Feed

PART # CED TEETH RAKE KERF GRIND70-120 2 16 0° .095 TCG70-122 21⁄2 20 0° .095 TCG70-124 3 20 0° .095 TCG70-126 31⁄2 20 0° .095 TCG70-128 4 20 0° .095 TCG

Soft Plastic - Fast Feed

PART # CED TEETH RAKE KERF GRIND70-140 2 10 -5° .095 TCG70-142 21⁄2 10 -5° .095 TCG70-144 3 10 -5° .095 TCG70-146 31⁄2 10 -5° .095 TCG70-148 4 10 -5° .095 TCG

Hard Plastic - Slow Feed

PART # CED TEETH RAKE KERF GRIND70-160 2 16 -5° .095 TCG70-162 21⁄2 20 -5° .095 TCG70-164 3 20 -5° .095 TCG70-166 31⁄2 20 -5° .095 TCG70-168 4 20 -5° .095 TCG

Hard Plastic - Fast Feed

PART # SHK DIA OAL70-180 1⁄2 31⁄470-181 1⁄2 41⁄270-182 5⁄8 31⁄470-184 3⁄4 31⁄4

Saw Arbor These saw arbors are designed to hold the carbide tipped saws.

PART# CED COLLAR SHK DIA KERF OAL ROTATION70-202 1 9⁄16 3⁄8 .062 31⁄4 Right Hand70-204 1 9⁄16 1⁄2 .062 4 Right Hand70-206 1 9⁄16 3⁄8 .062 31⁄4 Left Hand70-208 1 9⁄16 1⁄2 .062 4 Left Hand70-222 11⁄4 5⁄8 3⁄8 .062 31⁄4 Right Hand70-224 11⁄4 5⁄8 1⁄2 .062 4 Right Hand70-226 11⁄4 5⁄8 3⁄8 .062 31⁄4 Left Hand70-228 11⁄4 5⁄8 1⁄2 .062 4 Left Hand70-232 11⁄2 3⁄4 3⁄8 .062 31⁄4 Right Hand70-234 11⁄2 3⁄4 1⁄2 .062 4 Right Hand70-236 11⁄2 3⁄4 3⁄8 .062 31⁄4 Left Hand70-238 11⁄2 3⁄4 1⁄2 .062 4 Left Hand

SOLID CARBIDE SAW FLUSH MOUNT

SERIES 70-200

These small diameter solid carbide arbor

mounted saws are designed

for trimming andslotting plastics.

Saws are permanentlyattached to

arbors and are not reversible.

PART# CED TEETH RAKE SHK DIA KERF OAL GRIND ROTATION PLASTIC FEED70-300 2 10 0° 1⁄2 .095 4 TCG RH Soft Slow70-302 2 10 0° 1⁄2 .095 4 TCG LH Soft Slow70-320 2 16 0° 1⁄2 .095 4 TCG RH Soft Fast70-322 2 16 0° 1⁄2 .095 4 TCG LH Soft Fast70-340 2 10 -5° 1⁄2 .095 4 TCG RH Hard Slow70-342 2 10 -5° 1⁄2 .095 4 TCG LH Hard Slow70-360 2 16 -5° 1⁄2 .095 4 TCG RH Hard Fast70-362 2 16 -5° 1⁄2 .095 4 TCG LH Hard Fast

CARBIDE TIPPEDSAW FLUSH MOUNT

SERIES 70-300

These carbidetipped saws are

designed for flushtrimming and

slotting of bothhard and soft plastics. Saws

are permanentlyattached to

arbors and are not reversible.

SPECIALTY TOOLS

17

PART # CED CEL SHK DIA OAL56-063 3⁄16 5⁄8 1⁄4 456-084 1⁄4 11⁄4 1⁄4 456-086 1⁄4 11⁄4 1⁄4 456-124 3⁄8 15⁄8 3⁄8 656-164 1⁄2 21⁄8 1⁄2 6See Pages 5 & 13 for Complete Series and Tolerances

These tools haveextended reach andunique geometry for

five axis routing,trimming of formed

parts and plastic

SERIES 56-000

SOLID CARBIDE DOUBLEEDGE STRAIGHT FOR ACRYLIC& HARD PLASTICS

PART # CED CEL SHK DIA OAL61-043 1⁄8 5⁄8 1⁄4 461-063 3⁄16 1 1⁄4 461-084 1⁄4 11⁄4 1⁄4 461-123 3⁄8 15⁄8 3⁄8 661-166 1⁄2 21⁄8 1⁄2 6See Page 7 for Complete Series and Tolerances

These tools haveextended reach andunique geometry for

five axis routing,trimming of formed

parts and plastic

SERIES 61-000

SOLID CARBIDE SINGLE EDGE STRAIGHTS FOR SOFT PLASTICS

PART # EXT SHK SHK HEADOAL DIA LENGTH DIA COLLET

33-30 5 3⁄8 4 1⁄2 ER833-32 69⁄16 1⁄2 51⁄2 5⁄8 ER1133-34 61⁄4 5⁄8 51⁄2 5⁄8 ER1133-36 7 1⁄2 51⁄2 7⁄8 ER1633-38 69⁄16 3⁄4 51⁄2 7⁄8 ER16

TOOL EXTENDER*

* NOTE:Collet and Wrench

sold seperately.

These extensions aredesigned to increase

the overall reach of3⁄8" and smaller routerbits. These extensions

are used mainlyon CNC routers

when routing threedimensional parts.

SERIES 33-30

PART # COLLET SIZE TYPE33-50 1⁄8 ER833-51 1⁄8 ER1133-52 3⁄16 ER1133-53 1⁄4 ER1133-54 1⁄8 ER1633-55 3⁄16 ER1633-56 1⁄4 ER1633-57 5⁄16 ER1633-58 3⁄8 ER16

Collets for tool extender

SERIES 33-40/33-50

PART # CED CEL SHK DIA OAL52-240B 1⁄8 1⁄2 1⁄4 252-260B 3⁄16 3⁄4 1⁄4 252-280B 1⁄4 7⁄8 1⁄4 21⁄252-320B 3⁄8 11⁄8 3⁄8 352-360B 1⁄2 11⁄8 1⁄2 3CED TOLERANCE +.000 - .004

SOLID CARBIDEDOUBLE EDGEUPCUT SPIRALBALL NOSE

These double edge tools are

designed for carvingand modeling

operations.Theirimproved tip

geometry gives asuperior cut to

ballnose endmills,straight ball end

cutters and standard core

box cutters.


Specialty

SERIES 52-200B

PART # CED CEL SHK DIA OAL52-240BL 1⁄8 1⁄2 1⁄4 352-260BL 3⁄16 3⁄4 1⁄4 352-280BL 1⁄4 1 1⁄4 452-320BL 3⁄8 11⁄4 3⁄8 452-360BL 1⁄2 11⁄2 1⁄2 5CED TOLERANCE +.000 - .004

For carving and modeling.

SOLID CARBIDEDOUBLE EDGEUPCUT EXTENDEDLENGTH BALL NOSE

These double edge tools are

designed for carvingand modeling

operations.Theirimproved tip

geometry gives asuperior cut to

ballnose endmills,straight ball end

cutters and standard core

box cutters.


Specialty

SERIES 52-200BL

5 AXIS/ROBOTIC TOOLS

COLLETand WRENCH

For carving and modeling.

For extended

reach.

PART # EXTENSION PART #33-40 33-3033-42 33-32/33-3433-44 33-36/33-38

Wrench to tighten ER extension collet nuts.

18

SPECIALTY TOOLS

LEFT HAND ROTATION TOOLS

AIR ROUT TOOLS

PART # CED CEL SHK DIA OAL12-79 1⁄4 1 1⁄4 31⁄412-37 1⁄4 11⁄4 1⁄4 31⁄412-55 3⁄8 1 3⁄8 31⁄2See Page 5 for Complete Series and Tolerances

Usage:Foam, Nylon

SERIES 12-00


PART # CED CEL SHK DIA OAL48-155 3⁄8 11⁄4 3⁄8 3See Page 10 for Complete Series and Tolerances


Phenolic

SERIES 48-000

CARBIDE TIPPEDSINGLE EDGE

PART # CED CEL SHK DIA OAL48-058 3⁄8 11⁄4 3⁄8 3See Page 10 for Complete Series and Tolerances


Phenolic

SERIES 48-000

CARBIDED TIPPEDDOUBLE EDGESTRAIGHT

PART # CED CEL SHK DIA OAL56-062L 3⁄16 5⁄8 1⁄4 256-082L 1⁄4 3⁄4 1⁄4 21⁄256-122L 3⁄8 7⁄8 3⁄8 21⁄256-162L 1⁄2 1 1⁄2 356-625L 1⁄4 1 1⁄4 21⁄2See Page 5 & 6 for Complete Series and Tolerances

These tools are used in left rotation spindles which turncounter clock wise.

SERIES 56-000/56-600

SOLID CARBIDE DOUBLEEDGE STRAIGHT FLUTE FORACRYLIC & HARD PLASTICS

PART # CED CEL SHK DIA OAL61-042L 1⁄8 1⁄2 1⁄4 261-062L 3⁄16 5⁄8 1⁄4 261-082L 1⁄4 3⁄4 1⁄4 21⁄261-083L 1⁄4 3⁄4 1⁄4 31⁄4See Page 7 for Complete Series and Tolerances

These tools are usedin left rotation

spindles which turncounter clock wise.

SERIES 61-000

SOLID CARBIDE SINGLE EDGE STRAIGHT FLUTE FORSOFT PLASTICS

PART # CED CEL SHK DIA OAL48-678* 1⁄4 3⁄4 1⁄4 31⁄448-679 1⁄4 3⁄4 1⁄4 31⁄448-635* 3⁄8 1 3⁄8 31⁄248-636 3⁄8 1 3⁄8 31⁄2* DENOTES SINGLE EDGE - ALL OTHERS ARE DOUBLE.

See Page 4 for Complete Series and Tolerances

These tools aredesigned and

toleranced for airrouters. They have

a longer shank,extended reach

and are ground to fit through the

guide bushing.

SERIES 48-600

CARBIDE TIPPED PLASTICSTRAIGHT FOR HARD PLASTICS

PART # CED CEL SHK DIA OAL56-063 3⁄16 5⁄8 1⁄4 456-084 1⁄4 3⁄4 1⁄4 31⁄456-086 1⁄4 11⁄4 1⁄4 456-124 3⁄8 15⁄8 3⁄8 6See Pages 5 & 13 for Complete Series and Tolerances





guide bushing.

SERIES 56-000

SOLID CARBIDE DOUBLEEDGE STRAIGHT FOR ACRYLICAND HARD PLASTICS

PART # CED CEL SHK DIA OAL61-083 1⁄4 3⁄4 1⁄4 31⁄461-084 1⁄4 11⁄4 1⁄4 4See Page 7 for Complete Series and Tolerances





guide bushing.

SERIES 61-000

SOLID CARBIDE SINGLE EDGE STRAIGHT FOR SOFT PLASTICS

PART # CED CEL SHK DIA OAL11-75* 1⁄8 5⁄8 1⁄4 31⁄411-77* 3⁄16 3⁄4 1⁄4 31⁄411-71* 1⁄4 3⁄4 1⁄4 31⁄411-72 1⁄4 3⁄4 1⁄4 31⁄411-76 1⁄4 3⁄4 1⁄4 33⁄411-78 1⁄4 2 1⁄4 31⁄411-73* 3⁄8 1 3⁄8 31⁄211-74 3⁄8 1 3⁄8 31⁄2* DENOTES SINGLE EDGE - ALL OTHERS ARE DOUBLE.

See Page 6 for Complete Series and Tolerances





guide bushing.

SERIES 11-00

HIGH SPEED STEEL PLASTIC O FLUTE STRAIGHT FOR SOFT PLASTICS

SPECIALTY TOOLS

ACCESSORIES

PART # CED SHK SHK DOC* # OF DIA LENGTH WINGS

Straight

90-002 21⁄2 1⁄2 2 1⁄2 290-006 4 3⁄4 21⁄4 1⁄2 3Up-Shear90-004 21⁄2 1⁄2 2 1⁄2 290-008 4 3⁄4 21⁄4 1⁄2 3These tools are CNC balanced and approved for use on High Speed Spindles. Recommended RPM - 18000 MAX Feed Rates 200-400 IPM at 1⁄8” Depth of cut MAX.* DOC = Maximum Depth of Cut

For use on High Speed

Spindles.

SPOILBOARDSURFACING CUTTERS

These spoilboardsurfacing cutters are

used for surfacingMDF, particleboard,

and balsa corewhere “flow

through” or “highflow” cutting is

employed usinglarge capacity

vacuum pumps.Thismethod of surfacing

spoilboards allowsfor much faster

table planingwith the larger

diameters offered.

REPLACEMENT PARTS

90-052 Inserts 10/pk90-102 Screws90-104 Wrench

The replaceable insertsallow quick change indexingof worn inserts allowing newedges to be “rotated” intouse. The Straight versionswork well for MDF andparticleboard while theUp-Shear versions are bestutilized in the balsa corematerial due to the cleanercutting action.

SERIES 90-000

PART # CED CEL SHK DIA OAL70-502 1⁄8 11⁄2 1⁄8 23⁄470-506 5⁄32 115⁄16 5⁄32 31⁄870-510 3⁄16 21⁄8 3⁄16 31⁄270-514 1⁄4 27⁄16 1⁄4 470-520* 5⁄16 13⁄4 1⁄4 31⁄870-524* 3⁄8 21⁄4 1⁄4 43⁄870-528* 7⁄16 21⁄2 1⁄4 43⁄470-532* 1⁄2 25⁄8 1⁄4 51⁄8* SHANK LENTH 7⁄8

Designedspecifically for plastics.

PLASTIC DRILLSWITHSPECIAL POINT

Special tool steel,surface treated body,

flute and point formaximum lubrication.

Point is precisionground at 60°

angle for gradualpenetration to

minimize crackingand chipping of plastic materials.

0° rake angle on thecutting edge

eliminates grabbingas the drill comes

through the plastic surface.

SERIES 70-500

PART # OD HOLE LENGTH33-01 1⁄4 1⁄8 11⁄433-02 1⁄4 3⁄16 11⁄433-03 1⁄2 1⁄4 11⁄233-04 1⁄2 5⁄16 11⁄233-05 1⁄2 3⁄8 11⁄2CED TOLERANCE ± .002

For a temporary

substitute for the proper size collet.

FIBER ADAPTER BUSHING

These bushings areused to downsize

the bore for smallershank diameters.Bushings are not

recommended forproduction routing.

They should be usedonly as a

temporary substitute for the

proper size collet.

Usage:Temporary collet

downsizing

SERIES 33-00

PART # OD HOLE LENGTH34-03 1⁄2 1⁄4 11⁄434-05 1⁄2 3⁄8 11⁄4CED TOLERANCE ± .0005, I.D. TOLERANCE ± .001

For a temporary

substitute for the proper size collet.

STEEL ADAPTERBUSHING

These bushings areused to downsize

the bore for smallershank diameters.Bushings are not

recommended forproduction routing.

They should be usedonly as a temporary

substitute for theproper size collet.

Usage:Temporary collet

downsizing

SERIES 34-00

19

ACCESSORIES

20

COLLET BRUSH KIT33-10 Collet Brush Kit (Includes 4 Brushes in Tube)

33-15 1⁄4” Brush

33-16 3⁄8” Brush

33-17 1⁄2” Brush

33-18 3⁄4” Brush

33-19 1” Brush

33-25 Collet Brush Kit (Includes 5 Brushes in Tube)

COLLET BRUSH KIT

SERIES 33-10

RUST-FREE STAIN REMOVER and T-9

Rust Free 8.45 OZ.T-9 4 OZ. Drip

RUST FREE™ is a cleaner designed to provide a simple solution to your collet cleaning needs.

Use T-9™ to protect parts from rustand corrosion. Designed to be usedafter RUST FREE™ – use on colletsand tool holders.

RUST & STAINREMOVER ANDWATERPROOFLUBRICATION

SERIES 33-21

PART # TYPE TOTAL TAPER HANDLE TAPERLENGTH LENGTH DIA MAX DIA

33-60 ISO-30 65⁄8 23⁄8 1 11⁄433-62 ISO-40 71⁄2 31⁄16 1 13⁄433-64 ISO-50 91⁄2 43⁄4 13⁄16 23⁄4

SPINDLE TAPER WIPER

Spindle taper wipersare used to insureclean spindle taperbefore installing colletchucks into CNCrouter spindles.

SERIES 33-60

COLLETLIFEPLUG

These collet plugsare designed to

keep full grip colletsfrom collapsing in

the back when therouter bit shank does

not fill the full gripcollet completely.

SERIES 34-50

PART # SIZE34-51 1⁄434-52 3⁄834-53 1⁄234-54 5⁄834-55 3⁄4

1. Rigidity of Set Up - Vibration is a major source of tool wear and poor finish. Adjust feed rate to minimize vibration. Often a faster rate can improve finishes.

2. Router Environment -Other variables that affect every routing application are spindle horsepower, rigidity and runout, collet condition, clamping system and tool sharpness. Adjust feed rate to achieve desired finish.

3. Number of Flutes -Single flute tools should be fed at a slightly higher rate(approximately 10%)than double flute tools.

4. Bit Diameter -This chart is for 1/4” diameter bits. Bit diameter feed factors are as follows: 3/8” dia. plus 10%, 1/2” dia. plus 20%.

5. Depth of Cut -Decrease feed rate approximately 25% for each multiple of the depth of cut.(If depth is 2 times, reduce by 25%. If depth is 3 times, reduce by 50%.)

6. Spindle Speed -Adjust feed rate chart on a linear basis relative to 18,000 spindle RPM (If spindle is 20,000 RPM increase feed rate by approximately 10%. If spindle is 14,500 RPM reduce feed rate by approximately 20%.)

7. Finish -Find the fastest feed rate that will enable you to obtain satisfactory finish for best tool life.

8. Routing Formulas:Chip Load = Feed Rate/(RPM x # cutting edges) Feed Rate = RPM x # cutting edges x chip loadSpeed (RPM) = Feed Rate /(# cutting edges x chip load)

IMPORTANT INFORMATION

TOOL SOFT HARD FIBROUS FOAMSERIES PLASTIC PLASTIC REINFORCEMENTS10-00 150 12511-00 150 12512-00 150 150 10040-550 30048-000 200 15048-600 200 15052-000 15052-200 20052-600 275 25056-000 250 15056-600 300 27557-000 15057-600 300 27560-200 350 300 25060-470 350 300 25061-000 350 30062-000 10062-700 20062-750 15062-800 20062-850 15063-000 10063-700 20063-750 15063-800 20063-850 15066-000 125 12566-200 150 15066-300 175 15067-000 12567-300 400 400

ROUTER BITS INCHES PER MINUTE

GENERAL GUIDELINES FOR TOOL MATERIAL AND GEOMETRY

TOOL MATERIALS

Solid Carbide Use for fibrous or abrasive plastics.

Carbide Tipped Use for general plastic cutting applications.

High Speed Steel Use for optimum surface finish.

TOOL GEOMETRY

Straight Flute Use for plastic hand feed applications.

Spiral Flute Use for plastic automaticfeed applications.

FLUTE GEOMETRY

Single Flute Use for faster feed rates in softer materials.

Double Flute Use for better finish in harder materials.

Upcut Spiral ↑ Use for grooving or slotting, for upward chip evacuation and best finish on bottom side of piece part.

Downcut Spiral ↓ Use for downward chip flow, better hold down in fixture and best finish on top side of piece part.

Up/Down Spiral Use for double laminated material and best finish on top and bottom side of piece part.

SAWS INCHES PER MINUTE

TOOL CED MAX SOFT HARD FIBROUSSERIES RPM PLASTIC PLASTIC REINFORCEMENTS

70-100 2” 18,000 150 150 15070-100 21⁄2” 16,000 150 150 15070-100 3” 14,000 150 150 15070-100 31⁄2” 12,000 150 150 15070-100 4” 10,000 150 150 15070-200 11⁄2” 14,000 150 150 150

& Smaller

70-300 2” 16,000 150 150 150

CNC ROUTER FEED CHARTBASED ON 18,000 RPM, 1⁄4” DIAMETER CUTTING EDGE AND 1⁄4” DEPTH OF CUT

These feed rates are only guide-lines. Actual speed & feed rates willdepend on individual equipmentand goals. Generally, the faster a bitis fed, the longer the edges will last.For maximum life, start at a “safe”rate, then push feed rate until eitherfinish is undesirable, or tool is riskingbreakage. Other factors that affectfeed rate are listed below.

NUMERICALTABLE OF CONTENTS

Series 10-00 PAGE 6

Series 11-00 PAGE 6

Series 12-00 PAGE 5,9

Series 16-50 PAGE 13





















Series 52-200B PAGE 17

Series 52-200BL PAGE 17


Series 54-000/59-000 PAGE 12

Series 55-000/58-000 PAGE 12




























Five Axis Tools PAGE 17

Air Rout Tools PAGE 18

Left Rotation Tools PAGE 18

CATALOG P-6

MEMBER

INTERNATIONAL ASSOCIATION OF PLASTICS DISTRIBUTORS

MEMBER

WOOD MACHINERYMANUFACTURERSOF AMERICA

PROFIT THROUGH AMERICAN TECHNOLOGY

ASMMAAmerican Supply & MachineryManufacturers' Association, Inc. Printed in USA

ISO 9001 Certified

800 Liberty Drive Libertyville, IL 60048 Phone: 847/362-1560 Fax: 847/362-5028www.onsrud.comwww.plasticrouting.com

Documents

Plastic Cutting Tools