8/19/2019 Plano Succion Flotante Opw en Ss 764-l545
1/2
A B C D E
A B C D E
1
2
3
4
5
1
2
3
4
5CONFIDENTIAL
DRAWN:
CHECKED:
MATERIAL: WEIGHT:
PART NUMBER:
DESCRIPTION:
SIZE:
D
INFORMATION, PLEASE CONTACT OUR ENGINEERING DEPT.THIS DRAWING IS
NOT TO BE SCALED. FOR ADDITIONAL
REV:
120
DESCRIPTIONPART NUMBERUMQTYITEM
3" SWIVEL,40FJ,SST,VITON,SBM'G SERVICE3940FJ-0302EA11
FLG, 150, RFSO, SST, 3"H30464MEA12
3" SST SCH40 PIPEHX103016EA13
REDUCER, CONC, S40, SST, 4X3H30370MEA14
1/2" SST ROUND BARHX103016EA15
SST PLATEHX88357EA16
SST PLATEHX87533EA47
ELBOW, LR, S40, SST, 3"H-10283-MEA18
LUGHX92424EA49
PINH-06098-REEA110
RETAINING RING, SSTH30345MEA211
INSPECTION CABLE ASSYH05438EA112
FLANGE HARDWARE KIT, 150LB, SS, 3"FHK-150-03-SSEA113
INSTRUCTION BOOKLET FLOATING SUCTIONH07819PAEA114
SST FLOAT W/ATTACHMENTCX03713EA115
3D GENERATED DRAWINGSHEET 1 OF 2SCALE: 0.130-SST
764-L545---1/02/14JLP
MO-DA-YRSIGNATURES3" FLOATING SUCTIONPROPRIETARY TO OPW, AND
SHOULD BE PROTECTED ACCORDINGLY.
THIS DOCUMENT CONTAINS INFORMATION WHICH IS
REVISIONS
DATE APPROVEDDRAWNDESCRIPTIONECN #LTR
-----
12
5
3
1
8
2
9
10
4
11
7
6
8/19/2019 Plano Succion Flotante Opw en Ss 764-l545
2/2
A B C D E
A B C D E
1
2
3
4
5
1
2
3
4
5CONFIDENTIAL
DRAWN:
CHECKED:
MATERIAL: WEIGHT:
PART NUMBER:
DESCRIPTION:
SIZE:
D
INFORMATION, PLEASE CONTACT OUR ENGINEERING DEPT.THIS DRAWING IS
NOT TO BE SCALED. FOR ADDITIONAL
REV:
114-1/4
3
3-3/4
4
1-7/8
7/87/16
3D GENERATED DRAWINGSHEET 2 OF 2SCALE: 0.100-SST
764-L545---1/02/14JLP
MO-DA-YRSIGNATURES 3" FLOATING SUCTIONPROPRIETARY TO OPW, AND
SHOULD BE PROTECTED ACCORDINGLY.
THIS DOCUMENT CONTAINS INFORMATION WHICH IS
DESCRIPTIONPART NUMBERUMQTYITEM
1/2" SST ROUND BAR4.000HX103016EA11
3" SST SCH40 PIPE109.375HX103016EA12
ELBOW, LR, S40, SST, 3"H-10283-MEA13
FLG, 150, RFSO, SST, 3"H30464MEA14
LUGHX92424EA45
REDUCER, CONC, S40, SST, 4X3H30370MEA16
SST PLATEHX87533EA47
SST PLATEHX88357EA18
NOTES:1. WELDING PER OPW WELD SPECIFICATIONS. REFERENCE
APPLICABLE WELD SPECIFICATIONS PER COMPONENT.2. COMPONENT
FACE(S) PERPENDICULAR TO CENTER LINE(S) ±.5°
3. ALL FLANGE BOLT HOLES TO STRADDLE CENTER LINE(S)4. PROTECT
FLANGE FACE(S) AND MACHINED SURFACESWHEN WELDING
5. ALIGN COMPONENTS AS SHOWN ±2°.6. CLEAN ALL WELDS USING A
STAINLESS STEEL ONLY WIRE BRUSH.
SEE DETAIL A
1 23 4567
8
0.400SCALE ADETAIL
TY P
TY P
TY P
