Upload
aasatti
View
217
Download
0
Embed Size (px)
Citation preview
8/12/2019 piping Eng test
1/2
DIMENSIONAL ACADEMY OF ENGINEERING
PIPING ENGINERRING
Time: 3 hours QUESTION PAPER I Total 100 Marks
Page 1 of 2
1. What is the ASME code followed for design of piping systems in Process pipings(Refineries & Chemical Industries)? - 2 Marks
i. B31.1 ii. B31.3 iii. B31.5 iv. B31.9
2. Write down the outside diameter of following pipe? - 2 Marks
i. 3 inch ii. 6 inch iii. 10 inch iv. 14 inch
3. What is the difference between Pipe and Tube? - 2 Marks
4. Normally where do we use the following? - 2 Marks
i. Eccentric reducers ii. Concentric reducers
5. What should be the radius of long radius elbow? - 2 Marks
6. Concentric reducer is used in pump suction. (Yes / No). Explain. - 4 Marks
7. What should be the radius of long radius elbow? - 2 Marks
8. What is the ASTM code for the following? - 2 Marks
i. CS pipe ii. CS fittings iii. CS flanges
9. What is the ANSI/ASME dimensional standard for steel flanges & fittings? - 2 Marks
i. B16.3 ii. B16.5 iii. B16.9 iv. B16.10
10. Which are the different types of Gaskets? - 2 Marks
11. Why do we provide Drip Leg in Steam Line? - 4 Marks
12. What is the normal upstream and downstream straight length of orificeflow meter? - 2 Marks
13. How do you calculate the pipe spacing? - 4 Marks
14. How do you calculate the width of Pipe rack? - 4 Marks
15. How do you calculate the thermal expansion in a pipe? - 2 Marks
16. What is the basic span of supports for 2/6/10/24 pipe. - 2 Marks
17. What is the purpose of expansion bellows? - 2 Marks
18. What are the Insulation materials used for piping systems . - 2 Marks
19. Which American institute standard does piping engineer refer(Write any 4)? - 2 Marks
Page 1 of 2 Total - 46 Marks
8/12/2019 piping Eng test
2/2
DIMENSIONAL ACADEMY OF ENGINEERING
PIPING ENGINERRING
Time: 3 hours QUESTION PAPER I Total 100 Marks
Page 2 of 2
20. What is the different ASME 31 code for pressure piping? - 2 Marks
i. Power piping. ii. Fuel Gas Piping. iii. Refrigeration Piping iv. Gas transmission& distribution piping system.
5. Which American standard is referred for selection of following piping element?
i. Flanges ii. Butt Welded fittings iii. Gasket iv. Socket & Threaded fittings
v. Valves vi. Pipes. - 10 Marks
21. How can flanges be classified based on Pressure- temperature ratings? - 3 Marks
22. How can flanges be classified based on facing? - 3 Marks
23. How can flanges be classified based on face finish? - 2 Marks
24. Which type of gasket is recommended for high temperature andhigh-pressure application? - 2 Marks
25. How the pipe fittings are classified based on end connections? - 5 Marks
26. What is the function of valves? - 2 Marks
27. How the valves are classified based on their function? - 5 Marks
28. What is Equipment layout design? & What are the essential data/ documentsrequired for preparation of equipment layout? - 5 Marks
29. How much space is kept in between column of pipe rack? - 2 Marks
30. How much Headroom clearance is required under the following typeof crossing? - 5 Marks
i. Structures/ pipe lines inside operating area. ii. From top of the Rail.
iii. Above crest of road for crane movement. iv. Above crest of road for Truckmovement.
v. Above crest of road between process units.
31. What are different types of pumps? - 2 Marks
32. How many types of centrifugal pump are available based on the Suctionand Discharge arrangement? - 2 Marks
33. What sort of drawing/ layout is required for piping layout? - 4 Marks
Page 2 of 2 Total - 54 Marks
Page 1 & 2 of 2 Total - 100 Marks