Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
14
Pilot Operated Regulator
1098-EGR
▶ 도시가스 지구정압기 (City Gate Station, Main Station)
▶ 도시가스 지역정압기 (District Station)
▶ 상·공업용 대유량 전용정압기 (빌딩, 공장, 병원, 학교)
▶ 산업용 대유량 기구 Governor (Mixer, Boiler, Furnace,
Plant Air Service)
용도
▶ 고정밀도, 대유량 - Loading Type Pilot 작동방식의 특성
인 Two Path Control System 채용과 Pilot 증폭효과로
대유량 조절에도 높은 정밀도 유지
▶ 유지보수용이 - 배관에 설치된 상태로 신속한 분해점검
가능
▶ 작동상태 확인가능 - Travel Indicator가 내장되어 있어
대략적인 사용량 확인및 작동상태 확인가능
▶ 소음방지 장치 내장 - Option 사양으로 Whisper TrimⓇ
Cage 장착하면 20dBA 정도의 소음감소효과
▶ Fail Close Type
특징
사양
▶ 접속구경 및 방식
접속구경 (Inch)접 속 방 식
Cast Iron Body Steel Body
1, 2NPT
ANSI 125FFANSI 250RF
NPTANSI 150, 300, 600RF,
BWE, SWE
3, 4, 6, 8ANSI 125FFANSI 250RF
ANSI 150, 300, 600RFBWE
▶ 최고입구압력
구 분 최고입구압력, MPa(Bar)
Main Valve 2.8 (28)
Pilot
61LD 1.1 (11)
61L, 61LE, 61H 2.8 (28)
61HP 4.1 (41)
6350 Series 4.1 (41)
▶ Actuator Size 별 사용최고압력
▶ 사용온도 범위 : -29℃ ~ 82℃
▶ Body 재질 : Cast Iron, Steel
ActuatorOutlet(Control)
PressureEmergency
Casing Pressure
Type Size MPa Bar MPa Bar
109830
40 (std)70
0.690.520.35
6.95.23.5
0.790.570.45
7.95.74.5
1098H 30 2.1 21.0 2.81 28.1
13
●용도▶도시가스 지구정압기(City Gate Station, Main Station)
▶도시가스 지역정압기(District Station)
▶상·공업용 대유량 전용정압기(빌딩, 공장, 병원, 학교)
▶산업용 대유량 기구 Governor(Mixer, Boiler, Furnace,
Plant Air Service)
●특징▶고정밀도, 대유량 - Loading Type Pilot 작동방식의 특
성인 Two Path Control System 채용과 Pilot 증폭효과
로 대유량 조절에도 높은 정밀도 유지
▶유지보수용이 - 배관에 설치된 상태로 신속한 분해점검 가
능
▶작동상태 확인가능 - Travel Indicator가 내장되어 있어
대략적인 사용량 확인및 작동상태 확인가능
▶소음방지 장치 내장 - Option 사양으로 WHISPER
TRIM� Cage 장착하면 20dB 정도의 소음감소효과
▶유량추정 - RegFlo부착으로 사용유량 추정 및 작동상태
원격감시 가능
●사양▶접속구경 및 방식
접속구경(INCH)
접속방식CAST IRON BODY STEEL BODY
1, 2NPT ANSI 125FFANSI 250RFANSI 125FFANSI 250RF
NPT ANSI 150, 300, 600RF,BWE, SWEANSI 150, 300, 600RFBWE
3, 4, 6, 8
▶최고입구압력
▶사용온도 범위:-29℃~66℃
▶Body재질:Cast Iron, Steel
▶Actuator Size 별 사용최고압력
구 분MAIN VALVE
최고입구압력, MPa(BAR)
PILOT
61LD61L, 61LE, 61H61HP6350 Series
2.8 (28)1.1 (11)2.8 (28)4.1 (41)4.1 (41)
ACTUATOR
TYPE SIZE
OUTLET(CONTROL)PRESSURE
MPa BAR
EMERGENCYCASING PRESSUREMPa BAR
109830
40 (std)7030
0.690.520.352.1
6.95.23.521.0
0.790.570.452.81
7.95.74.5
28.11098H
Natural Gas
Types 1098-EGR and 1098H-EGR
14
Figure 10. Seat Ring / Cage Removal or Installation Using Body as Holding Fixture
P1508
BODy FlANgE
P1507
SEAT RINgSCREwS INTO CAgE
CAgE SCREwS INTO BODy FlANgE
Figure 9. Trim Package Removal
3. Slowly open the hand valve in the control line and adjust the pilot setting if necessary. Set the monitoring regulator at a slightly higher control pressure than the working regulator.
4. Completely open the downstream block valve.
5. Slowly close the bypass valve, if any.
ShutdownInstallation arrangements vary, but in any installation it is important that the valves be opened or closed slowly and that the outlet pressure be vented before venting inlet pressure to prevent damage caused by reverse pressurization of the pilot or main valve. The following steps apply to the typical installation as indicated.
Single-Pilot, Dual-Pilot Regulator or wide-Open MonitorAs well as applying to a single-pilot regulator (Figure 3), the steps in this procedure are also valid for a dual-pilot regulator (Figure 4) or a wide-open monitoring installation (Figure 8) and just need to be repeated for each regulator in such an installation.
1. Slowly close the downstream block valve. If the control line is downstream of the block valve, also close the hand valve in the control line.
2. Slowly close the upstream block valve and the hand valve in the pilot supply line.
3. Slowly open the vent valve in the downstream pipeline. If the control line is downstream of the block valve, also open the vent valve in the control line. Permit all pressure to bleed out.
4. Slowly open the upstream pipeline vent valve. Allow all pressure to bleed out of both the piping and the pilot.
working Monitor 1. Slowly close the downstream block valve and the
hand valve in the downstream pressure control line.
2. Slowly close the upstream block valve and the hand valves in both pilot supply lines.
3. Slowly open all vent valves and permit all pressures to bleed out of the piping and regulators.
MaintenanceRegulator parts are subject to normal wear and must be inspected and replaced as necessary. The frequency of inspection and replacement of parts depends upon the severity of service conditions or the requirements of local, state and federal regulations. Due to the care Emerson™ takes in meeting all manufacturing requirements (heat treating, dimensional tolerances, etc.), use only replacement parts manufactured or furnished by Emerson.
The stem O-rings (key 6, Figure 14) on the Type 1098 or 1098H actuator can be lubricated during regularly scheduled maintenance, using the grease fi tting (key 28, Figure 14). Stem O-rings can be checked for damage during normal operation by line pressure leakage or unexpected grease extrusion from the actuator vent (key 27, Figure 14). All O-rings, gaskets and seals should be lubricated with a good grade of general-purpose grease and installed gently rather than forced into position. Be certain that the nameplates
15
Pilot Operated Regulator
1098-EGR
�
page 4
Bulletin71.2:1098-EGR
Figure 3. Construction Features
DETAIL OF TYPE 6352,6533, OR 6345L PILOT
DETAIL OF OPTIONALRESTRICTED CAPACITY CONSTRUCTION
BALANCEDVALVE PLUG
THREADEDSPRINGSEAT
SCREW-IN BLEEDRESTRICTION
SCREW-ONTRAVELSTOP REMOVABLE
VENT
BELLOWS
UNBALANCEDVALVE PLUG
VALVEPLUGSPRING
PIPE NIPPLETHAT CONNECTSTO PILOT SIDETAPPING(NOT SHOWN)
W3160–2*W3161–1*
TYPE 1098–EGR REGULATOR SHOWN WITH TYPE 6351 PILOT
DETAIL OF TYPE 1098H ACTUATOR
MAIN VALVEPLUG
TRAVEL INDICATORWITH REMOVABLEPROTECTOR
PISTONRING
UPPERSEAL
PORTSEAL
CONTROL LINECONNECTION
W3419–1
W3149–1*
BLEED HOLE
▶ 설정압력범위
Pilot Type설정압력범위,
kPa(Bar)
Spring
Part Number 색 상
61LD61L61LE
0.7~31.7~13.8
6.9~3414~69
34~10069~140
(0.007~0.03)(0.017~0.138)(0.069~0.34)(0.14~0.69)(0.34~1.0)(0.69~1.4)
1C6806272221B8863270221J8578270221B8864270221J8579271421B886527022
은색 (Cadmium)적색 (Red)황색 (Yellow)청색 (Blue)갈색 (Brown)녹색 (Green)
61H 69~450 (0.69~4.5) OY0664000A2 녹색줄 (Green Stripe)
61HP 240~690 (2.4~6.9) 1D387227022 청색 (Blue)
63523.5~1414~69
(0.035~0.14)(0.14~0.69)
14A9672X01214A9673X012
황색 (Yellow)흑색 (Black)
635321~280
241~862(0.21~2.8)(2.41~8.62)
1E3925270221K748527202
황색 (Yellow)적색 (Red)
6354L6354M6354H
590~13801210~15201380~2070
(5.9~13.8)(12.1~15.2)(13.8~20.7)
1L3461271421L34612714215A9258X012
청색 (Blue)청색 (Blue)녹색 (Green)
Y600AM
1~21.7~43.7~88~17
17~3131~48
(0.01~0.02)(0.017~0.04)(0.037~0.08)(0.08~0.17)(0.17~0.31)(0.31~0.48)
1B6538270521B6539270221B5370270521B5371270221B5372270221B537327052
적색 (Red)회색 (Unpainted)황색 (Yellow)녹색 (Green)연청색 (Light Blue)흑색 (Black)
16
Pilot Operated Regulator
1098-EGR
▶ 최대 최소 작동차압에 따른 Main Spring 선정표
Body Size,Inch (DN)
Spring PartNumber
and Color
Maximum AllowableDifferetial Pressure,
kPa (Bar)
Minimum Differential Pressure Requiredfor Full Stroke, kPa (Bar)
Size 30 Actuator Size 40 Actuator Size 70 Actuator
1 (25)
14A9687X012Green
410 (4.1) 24(0.24) 17(0.17) 6.9(0.069)
14A9680X012Blue
860 (8.6) 34(0.34) 28(0.28) 10(0.10)
14A9679X012Red
2800(28) or body rating limit, whichever is lower
48(0.48) 34(0.34) 17(0.17)
2 (50)
14A6768X012Yellow
140 (1.4) ... 14(0.14) 6.9(0.069)
14A6626X012Green
410 (4.1) 28(0.28) 21(0.21) 10(0.10)
14A6627X012Blue
860 (8.6) 42(0.42) 34(0.34) 14(0.14)
14A6628X012Red
2800(28)or body rating limit, whichever is lower
76(0.76) 69(0.69) 21(0.21)
3 (80)
14A677X012Yellow
140 (1.4) ... 17(0.17) 6.9(0.069)
14A6629X012Green
410 (4.1) 34(0.34) 28(0.28) 14(0.14)
14A6630X012Blue
860 (8.6) 55(0.55) 42(0.42) 17(0.17)
14A6631X012Red
2800(28) or body rating limit,whichever is lower
97(0.97) 76(0.76) 28(0.28)
4 (100)
14A6770X012Yellow
140 (1.4) ... 24(0.24) 9(0.09)
14A6632X012Green
410 (4.1) 69(0.69) 34(0.34) 17(0.17)
14A6633X012Blue
860 (8.6) 90(0.90) 55(0.55) 21(0.21)
14A6634X012Red
2800(28) or body rating limit,whichever is lower
150(1.5) 90(0.90) 34(0.34)
6 (150)
`15A2253X012Yellow
140 (1.4) ... 41(0.41) 15(0.15)
14A9686X012Green
410 (4.1) 90(0.90) 66(0.66) 28(0.28)
14A9685X012Blue
860 (8.6) 130(1.3) 97(0.97) 42(0.42)
15A2615X012Red
2800(28) or body rating limit,whichever is lower
... 130(1.3) 55(0.55
17
Pilot Operated Regulator
1098-EGR
16
●작동원리▶1098EGR은 전단압력을 작동의 매개물로 삼는다.
전단압력은 Pilot를 통하여 감압되어 Actuator의 Diaphragm에 Loading(하중)을 준다.
후단압력은 Actuator에서 Loading압력에 역 작용하며 동시에 Pilot Spring의 힘+대기압력과 반대방향으로 작용(Two
Pass Control) 함으로서 응답속도가 빠르다.
▶후단압력이 설정압력보다 낮을 때
가스사용량이 증가하여 후단압력이 Pilot Spring의 설정압력보다 아래로 떨어지면 Pilot Diaphragm에 힘이 가해져 Pilot
Valve Plug는 열려 추가의 Loading압력을 보낸다. 이 압력은 Stem을 통하여 주 Regulator의 Valve Plug를 열고 후
단 측으로 필요한 유량을 공급하게 된다. Actuator Diaphragm에 과다한 압력이 가해지면 Bleed Orifice (Type 61
Series Pilot) 또는 Bleed Hole(Type 6351 Pilot) 또는 Restriction(Type 6352, 6353, 6354, Series Pilot)을 통하여
후단 쪽으로 빠져 나간다
▶후단압력이 설정압력보다 높을 때
후단의 요구가 충족되면 후단압력이 증가하게 되고 이 압력은 Pilot Diaphragm과 Actuator Diaphragm에 작용한다.
Pilot에 작용된 압력이 Pilot Spring의 설정치를 넘어서게 되면 Pilot Diaphragm을 움직여 Pilot Valve Plug를 닫으면
더 이상의 Loading 압력공급이 중단되며 Bleed Valve가 열리면서 Loading 압력의 감소가 일어나 주 Regulator의
Valve를 닫히게 한다.
▶Main Diaphragm을 보호하기 위하여 모든 Pilot들은 Relief Valve를 가지고 있어서 주 Regulator의 Diaphragm양단
의 차압이 Model 별로 약 1~1.7Bar일때 Loading압력은 Relief Valve를 통하여 Regulator의 후단으로 방출된다.
Natural Gas
▶ 1098EGR은 전단압력을 작동의 매개물로 삼는다.
전단압력은 Pilot를 통하여 감압되어 Actuator의 Diaphragm에 Loading(하중)을 준다.
후단압력은 Actuator에서 Loading압력에 역 작용하며 동시에 Pilot Spring의 힘+대기압력과 반대방향으로 작용(Two Pass
Control) 함으로서 응답속도가 빠르다.
▶ 후단압력이 설정압력보다 낮을 때
가스사용량이 증가하여 후단압력이 Pilot Spring의 설정압력보다 아래로 떨어지면 Pilot Diaphragm에 힘이 가해져 Pilot Valve
Plug는 열려 추가의 Loading압력을 보낸다. 이 압력은 Stem을 통하여 주 Regulator의 Valve Plug를 열고 후단 측으로
필요한 유량을 공급하게 된다.
▶ 후단압력이 설정압력보다 높을 때
후단의 요구가 충족되면 후단압력이 증가하게 되고 이 압력은 Pilot Diaphragm과 Actuator Diaphragm에 작용한다.
Pilot에 작용된 압력이 Pilot Spring의 설정치를 넘어서게 되면 Pilot Diaphragm을 움직여 Pilot Valve Plug를 닫으면 더
이상의 Loading 압력공급이 중단되며 Bleed Valve가 열리면서 Loading 압력의 감소가 일어나 주 Regulator의 Valve를
닫히게 한다. Actuator Diaphragm에 과다한 압력이 가해지면 Bleed Orifice (Type 61 Series Pilot) 또는 Bleed Hole(Type
6351 Pilot) 또는 Restriction(Type 6352, 6353, 6354, Series Pilot)을 통하여 후단 쪽으로 빠져 나간다.
▶ Main Diaphragm을 보호하기 위하여 모든 Pilot들은 Relief Valve를 가지고 있어서 주 Regulator의 Diaphragm양단의 차압이
Model 별로 약 1~1.7Bar일때 Loading압력은 Relief Valve를 통하여 Regulator의 후단으로 방출된다.
작동원리
18
Pilot Operated Regulator
1098-EGR
입구압력kPa (Bar)
설정압력kPa (Bar)
Body Size (Inch)
2 3 4 6
20 (0.2) 2.2 (0.022) 790 1700 2640 5000
40 (0.4)2.2 (0.022) 1170 2520 3910 7300
20 (0.2) 910 1950 3030 5740
100 (1.0)
2.2 (0.022) 1990 4290 6700 12160
20 (0.2) 1890 4070 6350 11660
40 (0.4) 1730 3720 5790 10770
200 (2.0)
2.2 (0.022) 3060 6590 10330 18350
20 (0.2) 3060 6590 10330 18350
40 (0.4) 3040 6540 10220 18350
100 (1.0) 2680 5770 8980 16650
400 (4.0)100 (1.0) 이하 5090 10960 17190 30520
200 (2.0) 4720 10150 15820 29080
600 (6.0)200 (2.0) 이하 7130 15330 24040 42700
400 (4.0) 5040 12770 19850 37000
850 (8.5)
200 (2.0) 이하 9670 20800 32610 57930
400 (4.0) 9360 20140 31430 57210
600 (6.0) 7820 16830 26150 48870
1.2 MPa (12)
400 (4.0) 이하 13220 28450 44610 79240
600 (6.0) 12730 27380 42720 77880
850 (8.5) 10790 23210 36070 67370
1.5 MPa (15)
600 (6.0) 이하 16270 35010 54900 97500
850 (8.5) 15150 32590 50790 93250
1.2 MPa (12) 11570 24880 38610 72800
2.0 MPa (20)
850 (8.5) 이하 21350 45900 71750 127950
1.2 MPa (12) 21330 41990 65410 120480
1.5 MPa (15) 16660 35830 55660 104330
2.76 MPa (27.6)
1.2 MPa (12) 이하 29030 62460 98090 174220
1.5 MPa (15) 27670 59520 92820 169660
2.0 MPa (20) 23620 50800 78950 147510
(단위 : NM3/H, 비중 0.6 NG)유량표
19
Pilot Operated Regulator
1098-EGR
BodySizeInch
Piping Style
Line Size Equals Body Size 2 : 1 Line Size to Body Size
Standard Cage Whisper Trim Cage Standard Cage Whisper Trim Cage
Cg Cv
C1
Cg
C1
Cg Cv
C1
Cg
C1Regulating
WideOpen
Regulating
WideOpen
Regulating
WideOpen
Regulating
WideOpen
Regulating
WideOpen
Regulating
WideOpen
1 600 632 16.8 17.7 35.7 576 607 34.5 568 598 17.2 18.1 33.0 529 557 34.0
2 2280 2400 63.3 66.7 36.0 1970 2080 36.0 2050 2160 59.6 62.8 34.4 1830 1930 35.0
3 4630 4880 132 138 35.1 3760 3960 35.0 4410 4650 128 135 34.4 3630 3830 34.2
4 7320 7710 202 213 36.2 6280 6610 34.8 6940 7310 198 209 35.0 6020 6340 35.2
6 12900 13600 397 418 32.5 9450 9950 32.0 12100 12800 381 404 31.7 9240 9730 31.7
8 18480 19450 578 608 32.0 10660 11220 35.0 17370 18280 543 571 32.0 10020 10550 35.0
BodySizeInch
A
D G R
Z
ARScrewed CastIron Body, orScrewed or
600RF Steel Body
125FF CastIron Body, or150RF Steel
Body
250RF CastIron Body, or300RF Steel
BodyCast Iron
BodySteel Body
In. mm In. mm In. mm In. mm In. mm In. mm In. mm In. mm In. mm
1 8.25 210 7.25 184 7.75 197 3.88 98 8.62 219 4.06 103 12.00 305 13.75 349 3.00 76
2 11.25 286 10.00 254 10.50 267 4.56 116 9.12 232 4.06 103 13.31 338 15.06 383 3.12 79
3 13.25 337 11.75 298 12.50 318 5.31 135 11.31 287 5.06 129 16.50 419 18.25 464 3.88 98
4 15.50 394 13.88 352 14.50 368 6.56 167 12.69 322 5.06 129 19.12 486 21.12 536 5.12 130
6 20.00 508 17.75 451 18.62 473 8.06 205 13.62 346 8.00 203 20.25 514 23.25 591 6.62 168
ActuatorC.DIA
E HM
With PilotSpring Case Vent
Without PilotSpring Case Vent
Type Size In. mm In. mm In. mm In. mm In. mm
1098 30 11.38 289 5.69 144
7.88 200 9.50 241 9.31 2371098H 30 11.38 289 6.06 154
1098 40 13.12 333 5.75 146
1098 70 21.12 537 7.44 189 14.19 360 15.81 402 15.62 397Bulletin 71.2:1098-EGR
20
Figure 8. Type 1098-EGR Dimensions
IN. / mm
Z
(REMOVAL CLEARANCE FOR TRIM PACKAGE)
M
B1113_1_B
H
C1.94 /49.3
A/2
A
R
G
D
E
AR (ACTUATOR REMOVAL CLEARANCE)
Bulletin 71.2:1098-EGR
20
Figure 8. Type 1098-EGR Dimensions
IN. / mm
Z
(REMOVAL CLEARANCE FOR TRIM PACKAGE)
M
B1113_1_B
H
C1.94 /49.3
A/2
A
R
G
D
E
AR (ACTUATOR REMOVAL CLEARANCE)
유량계수
DIMENSIONS