PHOENIX SERIES TELESCOPING LIFTING COLUMNS...2 • Ph: (800) 477-5002 • Fax: (704) 588-1994 PHOENIX SERIES TELESCOPING LIFTING COLUMNS Table of Contents Since 1883 Duff-Norton has

PHOENIX SERIESTELESCOPING LIFTING COLUMNSDESIGN GUIDE

2 www.duffnorton.com • Ph: (800) 477-5002 • Fax: (704) 588-1994

PHOENIX SERIESTELESCOPING LIFTING COLUMNSTable of Contents

Since 1883 Duff-Norton has been at the forefront of motion technology and through continuous improvement and lean manufacturing models has established a reputation for the highest quality in engineering and design.

INTRODUCTION

ApplICATION ANAlySIS FORm . . . . 4-5

TElESCOpING lIFTING COlUmNS

Features & Benefits . . . . . . . . . . . . . . 6

mounting positions . . . . . . . . . . . . . . 7

Schematic Diagram . . . . . . . . . . . . . . 7

Selection Table . . . . . . . . . . . . . . . . 8

Selection Flow Chart . . . . . . . . . . . . . 9

pERFORmANCE TABlES

Single-Stage - Trapezoidal Screw . . . . . . .10

mulit-Stage - AGS Screw . . . . . . . . . . .11

Single-Stage - Ball Screw (Ku) . . . . . . . .12

pERFORmANCE DIAGRAmS

Duty Cycle 10% . . . . . . . . . . . . . . . .13

Duty Cycle 20% . . . . . . . . . . . . . . . .13

Buckling . . . . . . . . . . . . . . . . . . . .14

Critical Speed . . . . . . . . . . . . . . . . .14

Off-center load . . . . . . . . . . . . . . . .15

Efficiency G15 . . . . . . . . . . . . . . . . .15

With an ISO 9001 registration since 1994 all Duff-Norton products, standard or custom designed, have been held to the same rigorous testing and scrutiny to assure maximum performance and quality.

Duff-Norton actuator products are specially designed for a variety of industrial and commercial applications. Our actuators are used for opening and closing, tilting and pivoting, lifting and lowering and positioning.

3www.duffnorton.com • Ph: (800) 477-5002 • Fax: (704) 588-1994

WARNINGThe equipment shown in this catalog is intended for industrial use only and should not be used to lift, support, or otherwise transport people unless you have written statement from Duff-Norton, which authorizes the specific actuator used in your applications as suitable for moving people.

NOTEDuff-Norton has made every effort to ensure that the information contained in the publication is accurate and reliable. Determining the suitability of our products for specific applications is the user’s responsibility.

TEChNICAl DRAWINGS

Gear Type m . . . . . . . . . . . . . . . . . .16

Gear Type G . . . . . . . . . . . . . . . . . .16

Dimensions . . . . . . . . . . . . . . . . . .17

mounting Options . . . . . . . . . . . . . . .18

DImENSIONS & ACCESSORIES

Dimensions . . . . . . . . . . . . . . . . . .19

Accessories . . . . . . . . . . . . . . . . . .19

Gear limit Switch . . . . . . . . . . . . . . .19

hand Drive . . . . . . . . . . . . . . . . . . .19

Selection Flow Chart . . . . . . . . . . . . . 9

ORDER CODE INFORmATION . . . . . .20

TERmS OF SAlE . . . . . . . . . . . . . .21


APPLICATION ANALYSIS FORMTELESCOPING LIFTING COLUMN

Name: Company:

Address:

Email Address:

Phone Number: Ext: Fax:

The maximum load depends on the required lifting speed and the total lift. In order to offer you the best solution, kindly provide all of the following information:

Please let us know how the lifting columns will be installed:

If available, please forward a drawing of the complete installation where the position of the lifting columns, the function and main dimensions are shown.

Quantity of installations:

Quantity of lifting columns / Installation:

Axial load of the lifting columns:

per installation: Dynamic: lb

Static: lb

per column: Dynamic: lb

Static: lb

Type of load: o Tensile

o pressure

o Tensile and pressure

Stroke: Inches

Basic height: Inches (max. height in retracted state)

Vibrations: o No o yes

Impact or punch forces: o No o yes

Required lifting speed: in/min

Ambient temperature: ºF

load: o Centered load

o Off-center load Inches

WARNINGImproper use can result in personal injury. To avoid injury:• Do not use actuators to lift, support, or transport people, without written approval from Duff-Norton.• Read all product warnings and operating instructions.

Duff-Norton engineers will be pleased to make recommendations for your specific requirements. Complete this form and mail or fax it to Duff-Norton. There is no obligation for this service.Use a separate sheet to sketch your application, or send us your design drawings in complete confidence.


Other operating conditions are important for the function of lifting elements. Please describe any of the conditions shown below that are present in the environment: e.g. wood dust, cement dust, relative humidity in %, stopping accuracy, inaccessible location, hazardous duty environment etc.

Are lateral guides planned o yes o No

Describe the duty cycle

load cycles per hour: Days per week:

hours per day: Distance per cycle: Inches

Bevel gear box o yes o No

Range:

Ratio: o 1:1 o 1.5:1 o 2:1 o 3:1 o 4:1 o 5:1 o 6:1

motor o yes o No o hand wheel

Voltage: V

Frequency: hz

protection class:

Flexible shafts o yes o No (specifying distance between lifting elements or shaft lengths)

pillow block bearing o yes o No

Accessories

APPLICATION ANALYSIS FORM - CONT.TELESCOPING LIFTING COLUMN

To mail please send completed sheet to:Duff-Norton Application Engineersp.O. Box 7010, Charlotte, NC 28241

To Fax or Email please send to:704-588-1994 • [email protected]


PHOENIX SERIESTELESCOPING LIFTING COLUMNS1100 to 5600 lbs (5 to 25 kN)

■■ Compact, telescoping design minimizes footprint

■■ Integrated screw and guide rails simplify design and installation

■■ handles eccentric loads for maximum design flexibility

■■ Sleek design is ideal for applications where aesthetics are important

■■ Suitable for horizontal or vertical applications with compression and/or

tension loads

■■ Fully customizable: specify a motor or use your own; select mounting

position, screw type, and more to create the perfect solution for

your application

FEATURES & BENEFITS

OpTIONS

■■ Worm gear or bevel gear

■■ Acme, ball, or AGS screw (see page 8)

■■ Single- or multi-stage

■■ limit switch (required for multi-stage lifting columns, optional for single-stage columns)

■■ hand wheel

DESIGN: Acme screw, ball screw, or AGS screw

TEmpERATURE RANGE: 14ºF to 104ºF (-10ºC to 40ºC)*

TRAVEl: up to approximately 6 ft (2 m), depending on application

SpEED: up to 354 in/min (9 m/min)

*For higher or lower temperature operation, please consult our application engineers

M1A

M3A

M6AM5A

M4A

M2A

right

left

left

left

left

left


SChEmATIC DIAGRAm

Connecting shaft

Lifting column

Coupling

Standard motor

Bevel gear box

IEC flange

Gear limit switch

Pillow block

Schematic view 3.2

A2 A1

A1

Schematic view 2.1

Schematic view 3.1

A1

A2

A3

Schematic view 1.1

right left

Top view M1A

A1

A2 A3

Schematic view 2.2

(Motor)

A2

A4 A6

A7A5

A3

A1

Schematic view 4.1

(Motor)

lifting column, mechanically synchronized

mOUNTING pOSITIONS


PHOENIX SERIESTELESCOPING LIFTING COLUMNS1100 to 5600 lbs (5 to 25 kN)

SeriesSingle-stage Multi-stage

PH34 M1 PH45 M2 PH56 M3 PH56 G15 PH46 M3 PH 36 M3

Gearbox type M M M G M M

Number of levels single-stage single-stage single-stage single-stage two-stage Three-stage

Fdyn lb-f (kN) 1124 (5) 2248 (10) 5620 (25) 3372 (15) 2248 (10) 1798 (8)

Fstat lb-f (kN) 1124 (5) 2248 (10) 5620 (25) 3372 (15) 5620 (25) 5620 (25)

Standard screw T24x5 T30x6 T36x6 T30x6 A30x32 A30x32

Ball screw (Ku) K20x20 K25x25 K40x40 K32x20 — —

Gear Ratio N (fast) 4 4 6 2 6 6

Gear Ratio L (slow) 16 16 24 3 24 24

Max. power 20%at ambient temperature 20°C

(kW) 0.2 0.3 0.5 1 0.5 0.5

Max. power 10%at ambient temperature 20°C

(kW) 0.42 0.6 1.1 1.3 1.1 1.1

Overall efficiency (N-ratio) 0.29 0.28 0.24 See diagram efficiency page. 15

0.43 0.38

Overall efficiency (L-ratio) 0.22 0.2 0.17 0.3 0.27

Max. torque on the input shaft in-lb (Nm) 30 (3.4) 63 (7.1) 159 (18) 443/796* (50/90*) 159 (18) 159 (18)

Max. speed rpm 1500 1500 1500 3000 1500 1500

Weight empty lb (kg) 31 (14) 40 (18) 57 (26) 66 (30) 68 (31) 77 (35)

Weight per 100 mm stroke lb (kg) 5.7 (2.6) 7.5 (3.4) 8.8 (4.0) 7.9 (3.6) 6.6 (3.0) 6.2 (2.8)

SElECTION TABlE

*Ratio N/l

Gearbox

M: Worm gear

high ratio possible

low noise

high load capacity

Economical

G: Bevel gear

permanently resilient

multiple drives can be implemented

Good efficiency

low wear

Nearly unchanged twist play

Screw types

T: Trapezoidal screw (Tr)

Self-locking*

Economical

K: Ball screw (Ku)

high efficiency

A: AGS screw (AGS)

Special thread for use in multi-stage screw jacks element

Trapezoidal screw (Tr) Ball screw (Ku) AGS screw (AGS)

Selection by speed

Yes

Yes

Yes

Yes

Selection by buckling

Selection by performance

Selection by outreach

Compile order code Request quote / order

No

La

Fa

Bas

ic b

uild

hei

ght

Specified values:

• Fdyn: Lifting load (Lb)

• Fstat: Static load (Lb)

• v: Desired speed (in/min)

• ED: Duty cycle (%)

• GBH: Basic build height (in)

(height in the retracted condition

• La: Outreach (in)

(Distance of the load center of gravity from the middle of the column)

Please contact Duff-Norton

Phone: 704-588-4610

Toll free: 800-477-5002

E-mail: [email protected]


SElECTION FlOW ChART

PHOENIX SERIESTELESCOPING LIFTING COLUMNSSelection Flow Chart


PHOENIX SERIESTELESCOPING LIFTING COLUMNSPerformance Tables Single-Stage - Trapezoidal Screw

Speed Lifting Speed 5 kN 4 kN 3 kN 2.5 kN 2 kN 1.5 kN 1 kNn N L N L N L N L N L N L N L N L

rpm (m/min)4 Nm 1 Nm 3 Nm 1 Nm 2 Nm 1 Nm 2 Nm 1 Nm 2 Nm 1 Nm 1 Nm 1 Nm 1 Nm 0 Nm

P (kW)

1500 1.88 0.47 0.6 0.2 0.5 0.2 0.4 0.1 0.3 0.1 0.3 0.1 0.2 0.1 0.2 0.1

1000 1.25 0.31 0.4 0.1 0.3 0.1 0.3 0.1 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1

750 0.94 0.23 0.3 0.1 0.2 0.1 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1

600 0.75 0.19 0.2 0.1 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

500 0.63 0.16 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

300 0.38 0.09 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

100 0.13 0.03 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

50 0.06 0.02 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

Speed Lifting Speed 10 kN 8 kN 6 kN 4 kN 3 kN 2 kN 1 kNn N L N L N L N L N L N L N L N L


P (kW)

1500 2.25 0.56 1.4 0.5 1.1 0.4 0.9 0.3 0.6 0.2 0.5 0.2 0.3 0.1 0.2 0.1

1000 1.5 0.38 0.9 0.3 0.8 0.3 0.6 0.2 0.4 0.1 0.3 0.1 0.2 0.1 0.1 0.1

750 1.13 0.28 0.7 0.2 0.6 0.2 0.4 0.1 0.3 0.1 0.2 0.1 0.2 0.1 0.1 0.1

600 0.9 0.23 0.6 0.2 0.5 0.2 0.3 0.1 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1

500 0.75 0.19 0.5 0.2 0.4 0.1 0.3 0.1 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1

300 0.45 0.11 0.3 0.1 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

100 0.15 0.04 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

50 0.08 0.02 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

Speed Lifting Speed 25 kN 20 kN 15 kN 10 kN 5 kN 2.5 kN 1 kNn N L N L N L N L N L N L N L N L


P [kW]

1500 1.5 0.38 2.6 0.9 2.1 0.8 1.6 0.6 1.1 0.4 0.6 0.2 0.3 0.1 0.2 0.1

1000 1 0.25 1.7 0.6 1.4 0.5 1.1 0.4 0.7 0.3 0.4 0.1 0.2 0.1 0.1 0.1

750 0.75 0.19 1.3 0.5 1.1 0.4 0.8 0.3 0.5 0.2 0.3 0.1 0.2 0.1 0.1 0.1

600 0.6 0.15 1 0.4 0.8 0.3 0.6 0.2 0.4 0.2 0.2 0.1 0.1 0.1 0.1 0.1

500 0.5 0.13 0.9 0.3 0.7 0.3 0.5 0.2 0.4 0.1 0.2 0.1 0.1 0.1 0.1 0.1

300 0.3 0.08 0.5 0.2 0.4 0.2 0.3 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1

100 0.1 0.03 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

50 0.05 0.01 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

Speed Lifting Speed 15 kN 12.5 kN 10 kN 7.5 kN 5 kN 2.5 kN 1 kNn N L N L N L N L N L N L N L N L


P (kW)

3000 9 6 6.6 4.6 5.6 3.9 4.6 3.2 3.6 2.6 2.6 1.9 1.7 1.3 1.1 0.9

2250 6.75 4.5 5 3.4 4.2 2.9 3.5 2.4 2.7 1.9 2 1.4 1.2 0.9 0.8 0.7

1500 4.5 3 3.3 2.3 2.8 1.9 2.3 1.6 1.8 1.3 1.3 1 0.8 0.6 0.5 0.4

1000 3 2 2.2 1.5 1.9 1.3 1.5 1.1 1.2 0.9 0.9 0.6 0.6 0.4 0.4 0.3

750 2.25 1.5 1.7 1.1 1.4 1 1.2 0.8 0.9 0.6 0.7 0.5 0.4 0.3 0.3 0.2

500 1.5 1 1.1 0.8 0.9 0.6 0.8 0.5 0.6 0.4 0.4 0.3 0.3 0.2 0.2 0.1

300 0.9 0.6 0.7 0.5 0.6 0.4 0.5 0.3 0.4 0.3 0.3 0.2 0.2 0.1 0.1 0.1

100 0.3 0.2 0.2 0.2 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

pERFORmANCE TABlE phOENIX ph34 m1, Tr 24x5



pERFORmANCE TABlE phOENIX ph56 G15, Tr 30x6

max. duty cycle at 68°F (20°C) ambient temperature:

Operating mode S3 20% - 60 min.


Static only (dynamic not allowed)






PHOENIX SERIESTELESCOPING LIFTING COLUMNSPerformance Tables Multi-Stage - AGS Screw



P (kW)

1500 8 2 3.3 1.2 2.6 0.9 2 0.7 1.4 0.5 1.1 0.3 0.8 0.4 0.5 0.2

1000 5.33 1.33 2.2 0.8 1.8 0.6 1.3 0.5 0.9 0.3 0.7 0.2 0.5 0.3 0.3 0.1

750 4 1 1.6 0.6 1.3 0.5 1 0.4 0.7 0.3 0.5 0.1 0.4 0.2 0.2 0.1

600 3.2 0.8 1.3 0.5 1.1 0.4 0.8 0.3 0.6 0.2 0.4 0.1 0.3 0.2 0.2 0.1

500 2.67 0.67 1.1 0.4 0.9 0.3 0.7 0.2 0.5 0.2 0.4 0.1 0.3 0.1 0.2 0.1

300 1.6 0.4 0.7 0.2 0.5 0.2 0.4 0.1 0.3 0.1 0.2 0.1 0.2 0.1 0.1 0.1

100 0.53 0.13 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

50 0.27 0.07 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1



P (kW)

1500 8 2 3 1.1 2.6 0.9 2.3 0.8 1.9 0.7 1.6 0.6 0.9 0.3 0.5 0.2

1000 5.33 1.33 2 0.7 1.7 0.6 1.5 0.5 1.3 0.5 1 0.4 0.6 0.2 0.3 0.1

750 4 1 1.5 0.5 1.3 0.5 1.1 0.4 1 0.3 0.8 0.3 0.4 0.2 0.3 0.1

600 3.2 0.8 1.2 0.4 1 0.4 0.9 0.3 0.8 0.3 0.6 0.2 0.3 0.1 0.2 0.1

500 2.67 0.67 1 0.4 0.9 0.3 0.8 0.3 0.6 0.2 0.5 0.2 0.3 0.1 0.2 0.1

300 1.6 0.4 0.6 0.2 0.5 0.2 0.5 0.2 0.4 0.1 0.3 0.1 0.2 0.1 0.1 0.1

100 0.53 0.13 0.2 0.1 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

50 0.27 0.07 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

pERFORmANCE TABlE phOENIX ph46 m3, AGS32

pERFORmANCE TABlE phOENIX ph36 m3, AGS32


PHOENIX SERIESTELESCOPING LIFTING COLUMNSPerformance Tables Single-Stage - Ball Screw (Ku)

Speed Lifting Speed 5 kN 4 kN 3 kN 2.5 kN 2 kN 1.5 kN 1 kNn N L N L N L N L N L N L N L N L


P (kW)

1500 7.5 1.88 1.1 0.4 0.9 0.3 0.7 0.2 0.6 0.2 0.5 0.2 0.4 0.1 0.3 0.1

1000 5 1.25 0.8 0.2 0.6 0.2 0.5 0.2 0.4 0.1 0.3 0.1 0.3 0.1 0.2 0.1

750 3.75 0.94 0.6 0.2 0.5 0.2 0.4 0.1 0.3 0.1 0.3 0.1 0.2 0.1 0.2 0.1

600 3 0.75 0.5 0.1 0.4 0.1 0.3 0.1 0.2 0.1 0.2 0.1 0.2 0.1 0.1 0.1

500 2.5 0.63 0.4 0.1 0.3 0.1 0.2 0.1 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1

300 1.5 0.38 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

100 0.5 0.13 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

50 0.25 0.16 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1



P (kW)

1500 9.38 2.34 2.8 0.9 2.2 0.8 1.7 0.6 1.2 0.4 0.9 0.3 0.7 0.2 0.4 0.1

1000 6.25 1.56 1.8 0.6 1.5 0.5 1.1 0.4 0.8 0.3 0.6 0.2 0.4 0.2 0.3 0.1

750 4.69 1.17 1.4 0.5 1.1 0.4 0.9 0.3 0.6 0.2 0.5 0.2 0.3 0.1 0.2 0.1

600 3.75 0.94 1.1 0.4 0.9 0.3 0.7 0.2 0.5 0.2 0.4 0.1 0.3 0.1 0.2 0.1

500 3.13 0.78 0.9 0.3 0.7 0.3 0.6 0.2 0.4 0.1 0.3 0.1 0.2 0.1 0.1 0.1

300 1.88 0.47 0.6 0.2 0.4 0.2 0.3 0.1 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1

100 0.63 0.16 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

50 0.31 0.08 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

Speed Lifting Speed 25 kN 20 kN 15 kN 10 kN 5 kN 2.5 kN 1 kNn N L N L N L N L N L N L N L N L


P (kW)

1500 10 2.5 7.2 2.6 5.8 2.1 4.4 1.6 3 1.1 1.6 0.6 0.9 0.3 0.4 0.2

1000 6.67 1.67 4.8 1.7 3.9 1.4 2.9 1.1 2 0.7 1 0.4 0.6 0.2 0.3 0.1

750 5 1.25 3.6 1.3 2.9 1 2.2 0.8 1.5 0.5 0.8 0.3 0.4 0.2 0.2 0.1

600 4 1 2.9 1 2.3 0.8 1.8 0.6 1.2 0.4 0.6 0.2 0.3 0.1 0.2 0.1

500 3.33 0.83 2.4 0.9 1.9 0.7 1.5 0.5 1 0.4 0.5 0.2 0.3 0.1 0.1 0.1

300 2 0.5 1.4 0.5 1.2 0.4 0.9 0.3 0.6 0.2 0.3 0.1 0.2 0.1 0.1 0.1

100 0.67 0.17 0.5 0.2 0.4 0.1 0.3 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1

50 0.33 0.08 0.2 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1

Speed Lifting Speed 15 kN 12.5 kN 10 kN 7.5 kN 5 kN 2.5 kN 1 kNn N L N L N L N L N L N L N L N L


P (kW)

2250 — 15 — 5.2 — 4.4 — 3.6 — 2.8 — 2.1 — 1.3 — 0.8

1500 15 10 5 3.4 4.3 2.9 3.5 2.4 2.7 1.9 1.9 1.4 1.2 0.9 0.7 0.5

1000 10 6.67 3.4 2.3 2.8 1.9 2.3 1.6 1.8 0.3 1.3 0.9 0.8 0.6 0.5 0.4

750 7.5 5 2.5 1.7 2.1 1.5 1.7 1.2 1.4 0.9 1 0.7 0.6 0.4 0.4 0.3

500 5 3.33 1.7 1.1 1.4 1 1.2 0.8 0.9 0.6 0.6 0.5 0.4 0.3 0.2 0.2

300 3 2 1 0.7 0.9 0.6 0.7 0.5 0.5 0.4 0.4 0.3 0.2 0.2 0.1 0.1

100 1 0.67 0.3 0.2 0.3 0.2 0.2 0.2 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1

pERFORmANCE TABlE phOENIX ph34 m1, Ku20x20



pERFORmANCE TABlE phOENIX ph56 G15, Ku32x20






PHOENIX SERIESTELESCOPING LIFTING COLUMNSPerformance Diagrams - Duty Cycle

pERFORmANCE DIAGRAm - DUTy CyClE 10%

pERFORmANCE DIAGRAm - DUTy CyClE 20%

0 2 4 6 8 10 12 14 16

PH34 M1PH45 M2

PH36 M3

PH56 G15

PH56 G15 Ku

PH56 M3

12.5

10

7.5

5

2.5

0

15

PH56 M3 Ku

PH46 M3

PH34 M1 Ku PH45 M2 Ku

PH34 M1

PH45 M2

PH56 M3

PH56 G15

PH46 M3

PH36 M3

PH34 M1 Ku

PH45 M2 Ku

PH56 M3 Ku

PH56 G15 KuLifting Speed (m/min)

Lifting capacity (kN)

0 2 4 6 8 10 12 14 16

PH34 M1

PH45 M2

PH56 M3

PH56 G15

PH46 M3

PH36 M3

PH34 M1 Ku

PH45 M2 Ku

PH56 M3 Ku

PH56 G15 Ku

Lifting Capacity (kN)

PH34 M1PH45 M2

PH36 M3

PH34 M1 Ku

PH56 G15

PH45 M2 Ku

PH56 M3 Ku

PH56 G15 Ku

PH56 M3

PH46 M3

12.5

10

7.5

5

2.5

0

15

Lifting Speed (m/min)


PHOENIX SERIESTELESCOPING LIFTING COLUMNSPerformance Tables Phoenix Buckling & Critical Speed

phOENIX BUCKlING

CRITICAl SpEED (TRApEZOIDAl SCREW)

0

5

10

15

20

25

PH34 M1

PH45 M2

PH56 M3

PH56 G15

PH46 M3

PH36 M3

PH34 M1 Ku

PH45 M2 Ku

PH56 M3 Ku

PH56 G15 Ku

Stroke (mm)

Permissible bucklingforce (kN)

PH34 M1

PH45 M2

PH36 M3

PH34 M1 Ku

PH56 G15

PH46 M3

PH45 M2 Ku

PH56 M3 Ku

PH56 G15 Ku

PH56 M3

5000 1000 1500 2000

0

2

4

6

8

Stroke (mm)

Lifting Speed (in/kN)

PH34 M1

PH45 M2

PH56 M3

PH56 G15

PH34 M1

PH45 M2

PH56 G15

PH56 M3

0 500 1000 1500 2000 2500 3000


PHOENIX SERIESTELESCOPING LIFTING COLUMNSPerformance Diagrams - Off-Center Load & Efficiency G15

phOENIX OFF-CENTER lOAD

EFFICIENCy G15

0

5

10

15

20

25

Outreach (mm)

Permissible Force (kN)

PH34 M1PH45 M2PH56 M3PH56 G15PH46 M3PH36 M3

La

Fa

PH34 M1

PH45 M2

PH36 M3

PH56 G15

PH46 M3

PH56 M3

0 100 200 300 400 500

Tr30x6

Ku32x20

Lifting capacity (kN)

Tr30x6

Ku32x20

0

80.0%

60.0%

40.0%

20.0%

0.0%2.5 5 7.5 10 12.5 15

With gear type M

Not applicable if stroke<G

B

BI

J

E

F

A

K

H

Output upon request

RightLeft

L

M

øN

øO

øS

P

¨C

¨D

Not applicable if stroke<G

B

B

J

E

F

A

K

H

With gear type G

Output upon request

L

M

øN

¨C

¨D

¨Q ¨R


PHOENIX SERIESTELESCOPING LIFTING COLUMNSTechnical Drawings - Gear Types M & G

TEChNICAl DRAWINGS

Size Single-stage Multi-stageDimensions [mm] PH34 M1 PH45 M2 PH56 M3 PH56 G15 PH46 M3 PH36 M3

A 260 + stroke + VL 300 + stroke + VL 340 + stroke + VL 369 + stroke + VL 375 + 1/2 stroke + VL 360 + 1/3 stroke + VL

oB 15 15 15 15 15 15

oC 138.6 160.6 182.6 182.6 182.6 182.6

D 116.6 138.6 160.6 160.6 138.6 116.6

E 170 195 220 249 220 199

F 1/2 stroke 1/2 stroke 1/2 stroke 1/2 stroke — —

G 300 350 400 400 — —

H M32x1.5 M32x1.5 M32x1.5 M32x1.5 M32x1.5 M32x1.5

I 15 22 35 — 35 45

J 80 90 100 100 100 90

øK H8 52 52 62 68 62 62

L 60 70 83.5 122 83.5 83.5

M 22.5 25.5 29 35 29 29

ø N 10 k6 14 k6 16 k612j6 (i=2)*18j6 (i=3)*

16 k6 16 k6

ø O 75 75 90 — 90 90

P 5 5 5 — 5 5

oQ ±0.3 210 210 210 210 210 210

oR 240 240 240 240 240 240

øS 11 11 11 11 11 11

* i = Ratio

phOENIX DImENSIONS


PHOENIX SERIESTELESCOPING LIFTING COLUMNSDimensions

Motor mounting flange

Max.øT

U

Gear limit switch Inductive limit switch

V

W

Stroke-X


PHOENIX SERIESTELESCOPING LIFTING COLUMNSTechnical Drawings - Mounting Options

TEChNICAl DRAWINGS - mOUNTING OpTIONS

Size Single-stage Multi-stageDimensions in (mm) PH34 M1 PH45 M2 PH56 M3 PH56 G15 PH46 M3 PH36 M3

Accessories

Motor mounting flange

ø T 4.72 (120) 5.51 (140) 6.29 (160) 6.29 (160) 6.29 (160) 5.51 (140)

U Dimensions according to quote or customer request

Gear limit switch

V 10.59 (269) 10.91 (277) 11.45 (291) 12.95 (329) 11.45 (291) 11.45 (291)

Inductive limit switch

W 125 145 165 194 — —

X 22 22 22 22 — —

Inductive limit switch (only single-stage column)Standard

Supply voltage 10-30V DC*

Connection M12

4 pins

Three-core

Attachment M12x1

Output NC

Switching current ≤ 200 mA

Length 41 mm

* AC optionally selectable, and with control from Columbus McKinnon Engineered Products GmbH

DImENSIONS phOENIX

ACCESSORIES

GEAR lImIT SWITCh hAND DRIVE

L + plug

■■ Necessary for multi-stage lifting columns

■■ Optional for single-stage lifting columns

■■ mounting on output shaft end

■■ Up to 8 switching points


PHOENIX SERIESTELESCOPING LIFTING COLUMNSDimensions and Accessories


PHOENIX SERIESTELESCOPING LIFTING COLUMNSOrder Code Information

ORDER CODE INFORmATION

PH - 1 1 - 2 2 2 - - - - - - - -

1 2 3 4 5 6 7 8 9 10

NO. Explanation

1 Size 34 / 45 / 56 / 45 / 36

2 Gear type M1 / M2 / M3 / G15* (*only possible with ph56)

3 Gear ratio N = fast / L = slow

4 Installation direction 1-6 = Alignment / A = motor at the large profile / B = motor at the small profile

5 Attachment plates 0 = Standard / X = Special

6 Stroke in mm

7 VL (extension as compared to the minimum basic build height)

8 Screw

or for special screw:

Screw diameter(smallest screw for multi-stage)

Screw pitch

0 = Standard screw

Screw typeT = Trapezoidal screw (Tr) / A = AGS screw (AGS) / K = Ball screw (Ku)

e.g. K32x20

9 Input/output shafts Gearbox type ML-R = Input left, output rightR-L = Input right, output leftL-0 = Input left, no outputR-0 = Input right, no output

Gearbox type G0 = no outputu = only output “u”v = only output “v”w = only output “w”uv = Outputs “u” and “v”uw = Outputs “v” and “w”vw = Outputs “v” and “w”uvw = Outputs “u”, “v” and “w”

10 Special options / accessories 0 = noneX = Special / accessories acc. to information / drawing

Examples:

PH45-M2-N-2A-0-300-50-0-R-01-stage PH45-M3 with ratio NSmall profile belowStandard head and foot plates300 mm stroke, 50 mm extensionStandard screwInput right, no output

PH56-G15-L-1A-X-600-0-K32x20-v-01-stage PH56-G15 with ratio LLarge profile belowSpecial head and/or foot plate600 mm stroke, no extensionBall screw Ku32x20Output at shaft end “v” (opposite input)

Gear type M

Gear type G

Input

Right

Output (upon request)

wu

v

Left


TERMS OF SALE

All sales by Seller are made pursuant to the following terms. No other or additional terms or conditions are or will be accepted.

ACCEPTANCE OF ORDERS - All orders, whether placed directly or through an agent, and all subsequent amendments thereto, are subject to a final approval and acceptance by Seller’s main office.

LIMITATION OF WARRANTIES, REMEDIES AND DAMAGES – THE WARRANTY STATED BELOW IS GIVEN IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE. NO PROMISE OR AFFIRMATION OF FACT MADE BY ANY AGENT OR REPRESENTATIVE OF SELLER SHALL CONSTITUTE A WARRANTY BY SELLER OR GIVE RISE TO ANY LIABILITY OR OBLIGATION. Seller warrants that on the date of its delivery to carrier the goods are free from defects in workmanship and materials. SELLER’S SOLE OBLIGATION IN THE EVENT OF BREACH OF WARRANTY OR CONTRACT OR FOR NEGLIGENCE OR OTHERWISE WITH RESPECT TO GOODS SOLD SHALL BE EXCLUSIVELY LIMITED TO REPAIR OR REPLACEMENT, F.O.B. SELLER’S POINT OF SHIPMENT, OF ANY PARTS WHICH SELLER DETERMINES TO HAVE BEEN DEFECTIVE or if Seller determines that such repair or replacement is not feasible, to a refund of the purchase price upon return of the goods to Seller. Any action against Seller for breach of warranty, negligence or otherwise must be commenced within one year after such cause of action accrues. NO CLAIM AGAINST SELLER FOR ANY DEFECT IN THE GOODS SHALL BE VALID OR ENFORCEABLE UNLESS BUYER’S WRITTEN NOTICE THEREOF IS RECEIVED BY SELLER WITHIN ONE YEAR FROM THE DATE OF SHIPMENT. Seller shall not be liable for any damage, injury or loss arising out of the use of the goods if, prior to such damage, injury or loss, such goods are (1) damaged or misused following Seller’s delivery to carrier; (2) not maintained, inspected, or used in compliance with applicable law and Seller’s written instructions and recommendations; or (3) installed, repaired, altered or modified without compliance with such law, instructions or recommendations. UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES AS THOSE TERMS ARE DEFINED IN SECTION 2-715 OF THE UNIFORM COMMERCIAL CODE.

TERMS OF PAYMENT - Unless otherwise stated herein, payment of each invoice is required within thirty (30) days after date of shipment. Any balance unpaid after the required payment date shall be subject to a service charge of 1% per month from such date.

PRICE ADJUSTMENTS - Amendments made by the Buyer to orders already placed shall, without formal notice to the Buyer, be subject to extra charges. If the estimated shipping date for the goods is more than sixty (60) days after date of order, the price of the goods are subject to increase by Seller.

TAXES - Any sales, use, excise, and other taxes applicable to this transaction and the goods and/or services furnished by Seller are not included in the price and shall be paid by Buyer when due. If Seller pays any such taxes, Buyer shall reimburse Seller upon demand.

INDEMNIFICATION AND SAFE OPERATION - Buyer shall comply with and require its employees to comply with directions set forth in instructions and manuals furnished by Seller and shall use and require its employees to follow such instructions and manuals and to use reasonable care in the use and maintenance of the goods. Buyer shall not remove or permit anyone to remove any warning or instruction signs on the goods. In the event of personal injury or damage to property or business arising from the use of the goods, Buyer shall, within forty-eight (48) hours thereafter, give Seller written notice of such injury or damage. Buyer shall cooperate with Seller in investigating any such injury or damage and in the defense of any claims arising therefrom. If Buyer fails to comply with this section or if any injury or damage is caused, in whole or in part, by Buyer’s failure to comply with applicable federal or state safety requirements, Buyer shall indemnify and hold Seller harmless against any claims, loss or expense for injury or damage arising from the use of the goods.

GOVERNING LAW - This agreement shall be governed by and construed under the laws of the State of New York.

DELIVERY AND DELAYS - Unless otherwise specified herein, deliveries shall be F.O.B. Seller’s point of shipment and risk of loss shall pass to Buyer upon Seller’s delivery to carrier. All shipping dates are approximate and Seller shall not be liable for loss or damage because of delays occasioned by labor disputes, damage to facilities, or failure of suppliers or subcontractors to meet scheduled deliveries or any other cause beyond Seller’s reasonable control or making its performance commercially impracticable. Not withstanding other provisions hereof, if shipment is delayed at Buyer’s request, the goods shall be deemed to be stored at Buyer’s risk and expense and Seller may thereupon bill Buyer for the full price and storage costs. Buyer shall pay such bill within 30 days after mailing thereof.

BUYER’S INSPECTION UPON RECEIPT OF SHIPMENT - Buyer shall inspect the goods as soon as received. If any loss or damage is discovered, Buyer must notify both the carrier and Seller at once. Seller will cooperate with Buyer in filing claims with the carrier.

CHANGES AND CANCELLATION - Seller reserves the right to change or cancel any order whenever circumstances require allocation of production or delivery or Seller deems change or cancellation to be necessary to comply with applicable laws, ordinances, regulations, directives or administrative actions. Seller reserves the right to make changes in materials or design which it determines appropriate for the goods.

SECURITY INTEREST AND REPOSSESSION - Until full payment has been made therefor, Seller shall have a security interest in goods shipped to Buyer and the goods shall remain personal property. Upon request Buyer shall execute and deliver to Seller security agreements and financing statements further evidencing Seller’s security interest. Buyer authorizes Seller to file a financing statement or statements relating to the goods, without Buyer’s signature thereon, as Seller may deem appropriate and appoints Seller as Buyer’s attorney-in-fact for the limited purpose of executing (without requiring Seller to do so) financing statements in Buyer’s name and performing other acts which Seller deems appropriate to perfect and continue its security interest and to protect and preserve the goods. In the event Buyer defaults in making any payment due Seller, Seller in addition to any other rights or remedies provided by law, shall have the right, with or without legal process, to enter the place where said goods are located and to repossess the goods in accordance with the Uniform Commercial Code.

ASSURANCES - Shipment by Seller shall at all times be subject to the prior approval of its credit personnel and Seller may, at any time, decline to make shipment except upon receipt of prior payment or upon other terms and conditions or security satisfactory to such personnel.

PATENTS - Except as to goods manufactured according to design supplied by Buyer, Seller will defend and hold Buyer free and harmless in a suit or proceeding brought against Buyer insofar as it is based on a claim that use of the goods by Buyer constitutes an infringement of any existing U.S. Patents, provided, however, that Buyer gives Seller prompt written notice of such suit or proceed-ing; permits Seller, through its counsel, to defend and/or settle the same; and gives Seller all necessary information, assistance and authority to enable Seller so to do. If Buyer’s use of the goods is held to constitute infringement and further use is enjoined, Seller shall, at its option, either (i) procure for Buyer the right to continue using the goods; or (ii) replace the goods with non-infringing goods; or (iii) modify the goods to non-infringing goods. The foregoing states Seller’s entire liability for patent infringement and shall not be construed to render Seller liable for damages based on product output.

MISCELLANEOUS - This instrument constitutes the entire agreement between Seller and Buyer, superseding all previous understandings and writings regarding this transaction. Any amendment or modification of this Agreement shall be void unless in writing and signed by Seller. No delay or omission by Seller in exercising any right or remedy hereunder shall be a waiver thereof or of any other right or remedy, and no single or partial exercise thereof shall preclude any other or further exercise thereof or the exercise of any other right or remedy. All rights and remedies of Seller are cumulative. Sales made pursuant to this Agreement shall be governed by the Uniform Commercial Code as the same may from time to time be construed and in effect in the state wherein Seller has its main office.

ARBITRATION - All disputes that may arise between the parties regarding the interpretation of the contract and the legal effect of the contract shall, to the exclusion of any court of law, be arbitrated and deter-mined in accordance with the latest Commercial Arbitration Rules of the American Arbitration Association. The arbitration proceeding shall be held in the city in that state where the principal office of the Seller is located. The parties recognize and consent to the above mentioned arbitration association’s jurisdiction over each and every one of them.

USTS rev. 2/98

ISO 9001 10000677

Duff-Norton ®

2018 © Yale Industrial Products, Inc., Duff-Norton DivisionAll rights reserved by Yale Industrial Products, Inc., Duff-Norton Division.May not be copied in whole or in part.

DN-PTLC-1 08/18

P.O. Box 7010 • Charlotte, NC 28241-7010Phone: (800) 477-5002 • (704) 588-4610Fax: (704) 588-1994Email: [email protected]

MOTION TECHNOLOGY

SCREW JACKS LINEARACTUATORS

ACME AND BALL SCREW & NUTS

ROTARY UNIONS

Documents

PHOENIX SERIES TELESCOPING LIFTING COLUMNS...2 • Ph: (800) 477-5002 • Fax: (704) 588-1994 PHOENIX SERIES TELESCOPING LIFTING COLUMNS Table of Contents Since 1883 Duff-Norton has