Philips Hadco-Roadway Luminaires

Roadway LuminairesSpecification Guide

Since 1953, we’ve built our products to a superior standard of quality and craftsmanship, using only the finest raw materials and components available. We’ve also built our business to a superior standard of consistency and reliability.

We inspect every piece we manufacture, multiple times, for fit and finish. Each of our designs is precision engineered, backed by ISO 9001 Certification. And our comprehensive warranties exceed industry standards.

But that doesn’t entirely explain how we became the industry leader. There’s another important area where we excel.

Service.

Smart. Prompt. And flexible.

At Philips Hadco, it has to be – because we provide the broadest selection of styles, finishes, and lamping options in the industry. Our superior service helps you navigate the choices and ensures that you’re getting just what you need. When you need it. Even if we have to custom design it.

When you light with Philips Hadco, you can rest assured it’ll be done right. On time.

That’s why more and more architects and designers depend on Philips Hadco. Because they know what they’ll get. Satisfaction.

Simply enhancing life with light

Roadway Contents

Profiler PA2 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Profiler PA31 . . . . . . . . . . . . . . . . . . . . . . . . . . 3Profiler PA4 . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Profiler PA5 . . . . . . . . . . . . . . . . . . . . . . . . . . . 7RX1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9RX2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11RX4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

21

Roa

dway

Roa

dway

100 Craftway Drive, P.O. Box 128, Littlestown, PA 17340 • Phone: 1-866-423-2658 • Fax: 717-359-0618

Ordering Guide

Ordering Example: PA2 C S I F 70S E V

OPTIONS (N) None (A) Air Filter MOUNTING VOLTAGE **(B) Button Eye (3) 3” O.D. Round Pole (E) 120V (F) Fusing ARM (4) 4” O.D. Round Pole FINISH OPTICS (F) 208V (G) Poly. Shield †(AT) Adjustable Arm (5) 5” O.D. Round Pole (A) Black (2) Type II (G) 240V ***(H) House-Side Shield ††(C) Curved Arm *(6) 6” O.D. Round Pole (B) White (3) Type III (H) 277V (Q) Quartz Restrike PRODUCT †(HT) Horiz. Slipfitter (S) Square Pole (H) Bronze (5) Type V (K) 347V (R) PE Receptacle CODE ††(S) Straight Arm (W) Wall Mount (I) Gray (F) Forward Throw WATTAGE (J) 480V (V) Tamper Resistant Latch PA2 ( ) ( ) ( ) ( ) 70S = 70W HPS ( ) ( ) PA2 ( ) ( ) ( ) ( ) 100S = 100W HPS ( ) ( ) PA2 ( ) ( ) ( ) ( ) 150S = 150W HPS ( ) ( ) PA2 ( ) ( ) ( ) ( ) 50H = 50W MH E, F, G, H, K ( ) PA2 ( ) ( ) ( ) ( ) 70H = 70W MH E, F, G, H, K ( ) PA2 ( ) ( ) ( ) ( ) 100H = 100W MH E, F, G, H, K ( ) PA2 ( ) ( ) ( ) ( ) 150H = 150W MH E, F, G, H, K ( )

*Only available with Straight Arm (S). **Not available in 480V (J). ***Not available with (5) or (F) optics.

†Do not specify mounting.††Order pole machined for this fixture.

For more information on the PA2, please visit www.hadco.com. Search by product name or number.

1. Housing: Die-cast aluminum

2. Arm: Die-cast aluminum

3. Lens: Clear tempered flat glass

4. Optics: Specular aluminum reflector

5. Socket: Porcelain 4kv rated medium base (Lamp not included)

6. Ballast: Factory pre-wired and tested

Housing: 360 low-copper die-cast aluminum alloy with

stainless steel fasteners and optional photo-control eye or

twistlock receptacle, which is located on the housing. Stainless steel

compression latch secures the lens frame to housing for tool-less

access to ballast and optical assembly.

Finish: Thermoset polyester powdercoat, laboratory tested for

superior weatherability and fade resistance.

Optical Assembly: Type II (2), Type III (3), Type V (5) and Forward

Throw (F) Cutoff: segmented specular internal reflector

with horizontal lamp mounting. All distributions are 90° rotatable

and interchangeable with a sealed optical chamber. Tempered

flat glass lens.

Lamping: H.I.D. Medium base ED17.

Electrical Assembly: Ballast assemblies are mounted on

a removable ballast tray with quick disconnects for tool-less

replacement.

Ballast: Factory pre-wired and tested, HPF core and coil.

Regulated with power factors better than 90% (HPF), providing

+/-10% input voltage regulation. Metal halide ballasts are capable

of starting at –20°F or –30°C and HPS –40°F or –40°C.

Certifications: ETL and cETL Listed. ISO 9001:2008.

Height/Width: 6˝ (15 cm) x 30 7/8˝ (78 cm)

Max. epa: (PA2S) 0.94 sq. ft.

(PA2C) 1.10 sq. ft.

Max. Weight: 38 lbs.

Shown: Profiler PA2C, Pole P195.

Profiler PA2

2 1

3

56

4

Adjustable Arm

Horizontal Slipfitter

Curved Arm

Straight Arm

43

Roa

dway

Roa

dway


Ordering Guide

Ordering Example: PA31 C W H F 150H K DF

OPTIONS OPTICS VOLTAGE (N) None MOUNTING (1) Type I (E) 120V ***(B) Button Eye ARM (3) 3” O.D. Round Pole FINISH (2) Type II (F) 208V (DF) Double Fusing *(AT) Adjustable Arm (4) 4” O.D. Round Pole (A) Black (3) Type III (G) 240V **(H) House-Side Shield †(C) Curved Arm (5) 5” O.D. Round Pole (B) White (4) Type IV (H) 277V (Q) Quartz Restrike PRODUCT *(HT) Horiz. Slipfitter (S) Square Pole (H) Bronze (5) Type V (K) 347V (R) PE Receptacle CODE †(S) Straight Arm (W) Wall Mount (I) Gray (F) Forward Throw WATTAGE (J) 480V (SF) Single Fusing PA31 ( ) ( ) ( ) ( ) 150S = 150W HPS ( ) ( ) PA31 ( ) ( ) ( ) ( ) 250S = 250W HPS ( ) ( ) PA31 ( ) ( ) ( ) ( ) 400S = 400W HPS ( ) ( ) PA31 ( ) ( ) ( ) ( ) 150H = 150W MH ( ) ( ) PA31 ( ) ( ) ( ) ( ) 250H = 250W MH ( ) ( ) PA31 ( ) ( ) ( ) ( ) 320H = 320W MH ( ) ( )

*Do not specify mounting. **Not available with Forward Throw (F), Type V (5), or Type I (1) optics.

***Not available in 480V (J).†Order pole machined for this fixture.



2. Arm: Extruded aluminum



5. Socket: Porcelain 4kv rated (Lamp not included)

6. Ballast: Factory pre-wired and tested

Housing: 360 low-copper die-cast aluminum alloy with

stainless steel fasteners and optional photo-control eye or

twistlock receptacle, which is located on the housing. Stainless steel

compression latch secures the lens frame to housing for tool-less

access to ballast and optical assembly.



Optical Assembly: Type I (1), Type II (2), Type III (3),

Type IV (4) Type V (5) and Forward Throw (F) Cutoff: segmented

specular internal reflector with horizontal lamp mounting.

All distributions are 90° rotatable and interchangeable with

a sealed optical chamber. Tempered flat glass lens.

Lamping: H.I.D. MH Mogul base ED28. 150W HPS Mogul base

ED23.5 250W-400W HPS Mogul base E18.

Electrical Assembly: Ballast assemblies are mounted

on a removable ballast tray with quick disconnects for

tool-less replacement.

Ballast: Factory pre-wired and tested, HPF core and coil.

Regulated with power factors better than 90% (HPF), providing

+/-10% input voltage regulation. Metal halide ballasts are capable of

starting at –20°F or –30°C and HPS –40°F or –40°C.


Height/Width: 8 1/8˝ (21 cm) × 33 3/4˝ (86 cm)

Max. epa: (PA31S) 1.36 sq. ft.

(PA31C) 1.46 sq. ft.


Profiler PA31

Shown: Profiler PA31S, Pole P295.

Profiler PA31

1

3

5

26

4

Adjustable Arm (Optional)

Horizontal Slipfitter (Optional)

Curved Arm (Optional)

Straight Arm (Standard)

65

Roa

dway

Roa

dway


Housing: Die-cast aluminum alloy, with stainless steel latch and

fasteners.



Optical Assembly: Precision formed, segmented aluminum

reflector with horizontal lamp mounting. Reflector is rotatable in

90º increments. This arc image duplicator system allows a full cutoff

and attains a 6:1 spacing-to-mounting-height ratio, while maintaining

a 3:1 average to minimum uniformity ratio for typical applications.

Electrical Assembly: The ballast assembly and components

are attached to the tool-less removable ballast tray assembly.

All components are ETL recognized and are an integral part of

the fixture. Socket is porcelain 4kv (position oriented) with

nickel-plated screw shell and center contact.

Lamping: PA4 Medium base: E17

Ballast: Factory wired and tested tool-less (HPF) ballast assembly

with quick disconnects for easy maintenance. MH ballasts are

capable of starting at -20F or -30C and HPS at -40F or-40C


IP Rating: IP65: completely dust tight and sealed to withstand low

pressure jets of water from any direction.

Height/Width: 7.7˝ (19 cm) × 23.2˝ (59 cm)

Max. epa: 0.9 sq. ft.


Ordering Guide

Ordering Example: PA4 S3 B I 70S E N

VOLTAGE OPTIONS MOUNTING OPTICS (E) 120V (N) None † (R3) 3” O.D. Round Pole FINISH (1) Type I (F) 208V (DF) Double Fusing † (R4) 4” or 5” O.D. Round Pole (A) Black (2) Type II (G) 240V (SF) Single Fusing † (S3) 3” Square Pole (B) White (3) Type III (H) 277V *(H) House-Side Shield PRODUCT †(S4) 4” or 5” Square Pole (H) Bronze (5) Type V (K) 347V **(Q) Quartz Restrike CODE † (W) Wall Mount (I) Gray (F) Forward Throw WATTAGE (J) 480V (R) TLR Receptacle PA4 ( ) ( ) ( ) 70S = 70W HPS ( ) ( ) PA4 ( ) ( ) ( ) 100S = 100W HPS ( ) ( ) PA4 ( ) ( ) ( ) 150S = 150W HPS ( ) ( ) PA4 ( ) ( ) ( ) 70H = 70W MH ( ) ( ) PA4 ( ) ( ) ( ) 100H = 100W MH ( ) ( ) PA4 ( ) ( ) ( ) 150H = 150W MH ( ) ( )

*Available with Type II and III optics only. **Consult factory when ordering Quartz Restrike (Q) with a 480V (J) ballast.

†Order pole machined for this fixture.


Profiler PA4

Shown: Pole P295, Fixture PA4.

Profiler PA4


2. Arm



5. Socket: Porcelain 4kv rated medium base

6. Ballast: Factory pre-wired

1

654

32

87

Roa

dway

Roa

dway


Ordering Guide

Ordering Example: PA5 S4 B 2 70S E N

VOLTAGE OPTIONS OPTICS (E) 120V (N) None MOUNTING FINISH (1) Type I (F) 208V (DF) Double Fusing † (R4) 4” or 5” O.D. Round Pole (A) Black (2) Type II (G) 240V (SF) Single Fusing † (R5) 5” or 6” O.D. Round Pole (B) White (3) Type III (H) 277V *(H) House-Side Shield PRODUCT †(S) Square Pole (4” or larger) (H) Bronze (5) Type V (K) 347V **(Q) Quartz Restrike CODE † (W) Wall Mount (I) Gray (F) Forward Throw WATTAGE (J) 480V (R) TLR Receptacle PA5 ( ) ( ) ( ) 150S = 150W HPS ( ) ( ) PA5 ( ) ( ) ( ) 250S = 250W HPS ( ) ( ) PA5 ( ) ( ) ( ) 400S = 400W HPS ( ) ( ) PA5 ( ) ( ) ( ) 150H = 150W MH ( ) ( ) PA5 ( ) ( ) ( ) 250H = 250W MH ( ) ( ) PA5 ( ) ( ) ( ) 320H = 320W MH ( ) ( )

*Available with Type II and III optics only. **Consult factory when ordering Quartz Restrike (Q) with a 480V (J) ballast.

†Order pole machined for this fixture.

For more information on the PA5 please visit www.hadco.com. Search by product name or number.


2. Arm



5. Socket: Porcelain 4kv rated medium base

6. Ballast: Factory pre-wired

Housing: Die-cast aluminum alloy, with stainless steel latch and

fasteners.



Optical Assembly: Precision formed, segmented aluminum

reflector with horizontal lamp mounting. Reflector is rotatable in

90º increments. This arc image duplicator system allows a full cutoff

and attains a 6:1 spacing-to-mounting-height ratio, while maintaining

a 3:1 average to minimum uniformity ratio for typical applications.

Electrical Assembly: The ballast assembly and components

are attached to the tool-less removable ballast tray assembly.

All components are ETL recognized and are an integral part of

the fixture. Socket is porcelain 4kv (position oriented) with

nickel-plated screw shell and center contact.

Lamping: PA5 Mogul base: MH ED28

PA5 HPS 150w ED23.5

PA5 HPS 250-400w E18

Ballast: Factory wired and tested tool-less (HPF) ballast assembly

with quick disconnects for easy maintenance. MH ballasts are

capable of starting at -20F or -30C and HPS at -40F or-40C


IP Rating: IP66: completely dust tight and sealed to withstand low

pressure jets of water from any direction.

Height/Width: 10.3˝ (26 cm) × 30.9˝ (78 cm)



Profiler PA5

Shown: Pole P295, Fixture PA4.

Profiler PA5

1

654

32

109

Roa

dway

Roa

dway


Ordering Guide

Ordering Example: RX180 A 4 N A 5 R N S N

DIMMING4

(N) None (DA) 4 Hrs 25% (DB) 4 Hrs 50% (DC) 4 Hrs 75% (DD) 6 Hrs 25% (DE) 6 Hrs 50% (DF) 6 Hrs 75% FINISH DISTRIBUTION COLOR (DG) 8 Hrs 25% (A) Black (2) Type II TEMP (CCT) DRIVE (DH) 8 Hrs 50% SURGE (B) White (3) Type III (W) 3000K VOLTAGE CURRENT PHOTOCELL (DJ) 8 Hrs 75% SUPPRESSION HOUSE SIDE SHIELD PRODUCT (H) Bronze (4) Type IV (N) 4000K (A) 120-277VAC (5) 530 mA (N) None (DZ) Custom5 (S) Standard <3kV (N) None CODE (I) Gray (5) Type V (C) 5700K (B) 347-480VAC3 (M) Multi Tap1 (R) Twist-Lock Receptacle (W) Wireless2 (A) 10kV BIL (H) House-Side Shield RX140 ( ) ( ) ( ) ( A ) ( M ) ( ) ( DZ, W, N ) ( ) ( ) RX164 ( ) ( ) ( ) ( ) ( 5 ) ( ) ( ) ( ) ( ) RX180 ( ) ( ) ( ) ( ) ( 5 ) ( ) ( ) ( ) ( )

1No dimming or 347-480V, available with (M) Multi Tap driver only available with RX140 – ships at 530mA.

2(W) Wireless option – consult factory.3347-480V not available with Dimming options (DA - DZ)

4DA-DZ equal the reduction of energy. 5(DZ) Custom option – consult factory.

For more information on the RX1, please visit www.hadco.com. Search by product name or number.

Housing: Die-cast housing, lens frame and door. Low-copper,

aluminum alloy. Unique thermal dissipating housing design.

Wide angular fin design reduces the build up of dirt and improves

thermal dissipation. Aesthetic look and sleek design looks similar

to a cobra-head style luminaire with a lower EPA value. Tool-less

access to wiring and driver compartment with removable door.

Robotically applied lens and lens frame gasket seals.

Finish: Thermoset polyester powdercoat, laboratory tested

for superior weatherability and fade resistance. Textured finish.

Mounting: The mounting detail accepts 1.5” O.D. to 2.5” O.D.

arm/horizontal tenon. Clamp mounting system for increased

reliability and safety. +5°/-5° mounting with leveling bubble.

Driver: Strategic placement of driver, lowering driver case

temperature by up to 20°C. Auto-sensing 120-277VAC,

347-480VAC, 50-60Hz input.

Optics: Precision designed injection-molded acrylic optic plates.

Multiple distribution options (Type 2, 3, 4, 5).

LED Specifications: 80,000 hours with >L70 lumen

maintenance @ 25°C. Multiple color temperature options

(3000K, 4000K, 5700K). Philips LEDGINE platform with

40, 64 or 80 LEDs.


IP Rating: IP66 rated LED Optics Chamber and Driver.

Length/Height/Width: 25.4˝ (64 cm) × 4.8˝ (12 cm) × 15.8˝ (40 cm)


Max. Weight: 19.5 lbs.

1. Housing: Die-cast housing

2. Door: Tool-less access to wiring

3. Lens: Tempered glass lens

4. Driver: Auto-sensing, factory wired

5. Optics: Precision designed, injection molded.

RX1RX1

4 532

1

Other: Large terminal block, directly in line with incoming power

wires, accepts up to 6 gauge wire. 360° rotatable twist-lock photo-

cell receptacle. 0-10V dimming capability within drivers and optional

programmable dimming module. 10kV BIL surge suppression (optional).

Philips Dynadimmer and wireless controls (optional).

Shown: Pole custom, Fixture RX1.

1211

Roa

dway

Roa

dway


RX2

Shown: Pole custom, Fixture RX2.

Housing: Die-cast housing, lens frame and door. Low-copper,

aluminum alloy. Unique thermal dissipating housing design.

Wide angular fin design reduces the build up of dirt and improves

thermal dissipation. Aesthetic look and sleek design looks similar

to a cobra-head style luminaire with a lower EPA value. Tool-less

access to wiring and driver compartment with removable door.

Robotically applied lens and lens frame gasket seals.




arm/horizontal tenon. Dual-clamp mounting system for increased

reliability and safety. +5°/-5° mounting with leveling bubble.

Driver: Strategic placement of drivers, lowering driver case

temperature by up to 20°C. Auto-sensing 120-277VAC, 347-

480VAC, 50-60Hz input.



LED Specifications: 80,000 hours with >L70 lumen

maintenance @ 25°C. Multiple color temperature options

(3000K, 4000K, 5700K). Philips LEDGINE platform with

120 or 160 LEDs.


IP Rating: IP66 rated LED Optics Chamber and Driver.

Length/Height/Width: 40.2˝ (102 cm) × 5.0˝ (13 cm) × 15.8˝ (40 cm)



RX2

1. Housing: Die-cast housing





4 532

1


wires, accepts up to 6 gauge wire. 360° rotatable twist-lock photo-

cell receptacle. 0-10V dimming capability within drivers and optional

programmable dimming module. 10kV BIL surge suppression (optional).

Philips Dynadimmer and wireless controls (optional).

Ordering Guide

Ordering Example: RX2120 A 4 N A 5 R N S N

DIMMING3

(N) None (DA) 4 Hrs 25% (DB) 4 Hrs 50% (DC) 4 Hrs 75% (DD) 6 Hrs 25% (DE) 6 Hrs 50% (DF) 6 Hrs 75% FINISH DISTRIBUTION COLOR (DG) 8 Hrs 25% (A) Black (2) Type II TEMP (CCT) (DH) 8 Hrs 50% SURGE (B) White (3) Type III (W) 3000K VOLTAGE DRIVE PHOTOCELL (DJ) 8 Hrs 75% SUPPRESSION HOUSE SIDE SHIELD PRODUCT (H) Bronze (4) Type IV (N) 4000K (A) 120-277VAC CURRENT (N) None (DZ) Custom4 (S) Standard <3kV (N) None CODE (I) Gray (5) Type V (C) 5700K (B) 347-480VAC2 (5) 530 mA (R) Twist-Lock Receptacle (W) Wireless1 (A) 10kV BIL (H) House-Side Shield RX2120 ( ) ( ) ( ) ( A ) ( 5 ) ( ) ( DZ, W, N ) ( ) ( ) RX2160 ( ) ( ) ( ) ( ) ( 5 ) ( ) ( ) ( ) ( )

1(W) Wireless option – consult factory.2347-480V not available with Dimming options (DA - DZ)

3DA-DZ equal the reduction of energy. 4(DZ) Custom option – consult factory.


1413

Roa

dway

Roa

dway


Housing: Sand-cast housing, lens frame and bottom.

Low-copper, aluminum alloy. Wide angular fin design

improves thermal dissipation. Unique style luminaire with

low profile and EPA. Tool-less access to wiring and driver

compartment with hinged bottom. High-temperature

silicone rubber lens gasket seal.




(.75” to 2” NPS) arm/horizontal tenon. Dual-clamp mounting

system for increased reliability and safety.

Driver: Strategic placement keeps driver case temperature

below the maximum rating. Auto-sensing 120-277VAC,

50-60Hz input. Multi-tap driver factory set for 350mA, 530mA

or 700mA (see Ordering Guide).



LED Specifications: Up to 100,000 hours with >L70 lumen

maintenance @ 25°C (see specification sheets for details).

Multiple color temperature options (4000K or 5700K – consult

factory for 3000K). Philips LEDGINE platform with 24 or 40 LEDs.


IP Rating: IP66 rated LED Optics Chamber and LED Driver.

Length/Height/Width:

no brim: 16.25˝ (41 cm) × 7.0˝ (18 cm) × 12.5˝ (32 cm)

with brim: 20.0˝ (51 cm) × 8.25˝ (21 cm) × 20.07˝ (51 cm)

Max. EPA: 0.30 sq. ft. (no brim) or 0.40 sq. ft. (with brim).

Max. Weight: 14.50 lbs. (no brim) or 16.25 lbs. (with brim).

RX4RX4

1. Housing: Sand-cast housing





4

5 3

2

1


wires, accepts up to 6 gauge wire. 360° rotatable twist-lock

photo-cell receptacle. 10kV/10kA surge suppression (optional).

Decorative Radial Wave Brim (optional). House Side Shield (optional).

Ordering Guide

Ordering Example: RX424 T1 A 2 N A 3 N S N N

FINISH DISTRIBUTION DRIVE (A) Black (2) Type II COLOR CURRENT SURGE HOUSE MOUNTING (B) White (3) Type III TEMP (CCT)1 (3) 350 mA PHOTOCELL SUPPRESSION SIDE SHIELD BRIM PRODUCT (T1) 2.60” - 2.25” tenon (H) Bronze (4) Type IV (N) 4000K VOLTAGE2 (5) 530 mA (N) None (S) Standard Built In <3kV (N) None (N) None CODE (T2) 2.25” - 1.00” tenon (I) Gray (5) Type V (C) 5700K (A) 120-277VAC (7) 700 mA (R) Twist-Lock Receptacle (A) Additional 10kV / 10kA (H) House Side Shield (B) Brim RX424 ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) RX440 ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )


Shown: Fixture RX4 with optional brim.

With Brim (Optional)

No Brim (Standard)

Shown: Fixture RX4.

1Warm 3000K CCT – consult factory. 2347-480VAC – consult factory.

15

Photo Gallery

Philips Hadco Teardrop fixtures offer an affordable alternative to the cobrahead traditionally used to light high traffic locations, while adding character.

The following images illustrate the function and versatility of Philips Hadco’s lighting fixtures, arms and poles while adding character to your environment’s setting.

A variety of Teardrops and Bollards allow you to create your own best combination – a hard working, easy-to-maintain system that provides security while accenting your environments’ setting.

Historical “Main Street” charm is preserved by using Philips Hadco’s Refractive Globe fixtures fitted with the latest optical efficiencies.

Properly placed post top fixtures provide much more than embellishment. These fixtures also serve as markers to direct visitors to main points of entry.

Precise optics of Philips Hadco’s Refractive Globes - coupled with a range of styles and options like banner arms and customizable street graphics, offer an attractive presence both day and night.

Architecturally pleasing fixtures are a welcomed addition to this roof-top application, adding safety and security to this public location.

Philips Hadco100 Craftway DriveP.O. Box 128Littlestown, PA 17340

Phone: 800-331-4185

Fax: 717-359-9289

www.hadco.com

PH-1077-1112-5K

Printed in U.S.A.

© 2011 Philips Group

All rights reserved. Certain products illustrated in this catalog may be protected by applicable patents and patent pending. Philips Hadco will aggressively defend all of its intellectual property. We reserve the right to change details of design, materials and finishes in any way that will not alter installed appearance or reduce function and performance.

Documents

Philips Hadco-Roadway Luminaires