Performance Credenza (and other Nucraft Credenzas) Kitchen Aid KDDO24RVX KDDO24CVX Custom Drawer Front Installation Instructions (see pg. 5 for GE)

[Rev. D , April 4, 2011]

Performance Credenza Kitchen Aid KDDC24RVX KDDO24CVX Custom Drawer Front Nucraft Furniture Company

2

Before Beginning Installation

• Hardware attached will work in conjunction to refrigerator hardware

• Only Kitchen Aid models KDDO24RVS and KDDO24CVX will work

• The refrigerator instructions in conjunction with these instructions. Due to the nature and appearance

of the credenza, the size, overlap, and attachment of the custom fronts will be different then what is

given in the refrigerator manufacturer’s instructions.

• Important to level both fridge and credenza best as possible

• Products pictured may not match particular installation

• Please read all of the instructions prior to beginning the assembly.

Tools Required For Assembly

• Tools needed:

o Level

o Drill

o Phillips bit

o 3/32” drill bit

o Wonder bar or equivalent crow bar

o Tape measure

o Pencil

o Masking Tape

Hardware

a. “L” Bracket x 4

b. #8 x ½” wood screw x 4

c. Two sided tape x 4

d. Mounting brackets included w/ refrigerator, 4 left & 4 right (flat brackets also included, Do not use for this

installation)

e. #8 x ½” wood screw included /w refrigerator, black flat head x 16

Performance Credenza Kitchen Aid KDDC24RVX KDDO24CVX Custom Drawer Front Nucraft Furniture Company

3

Leveling Case & Refrigerator

1. Place credenza to desired location.

There will be eight total glides to the inside

of the toe kick.

2. Level refrigerator, keep in mind only the

front glides will be accessible one it is in

place inside the credenza.

3. Slide the refrigerator inside the

credenza. It should sit about ¾” from flush.

Check the levelness again on the

refrigerator versus the case and make

adjustments if needed.

Installing Custom Fronts

1. Keep in mind, to create the look of the

credenza, the fronts will be larger than the

instructions included with the refrigerator.

2. On the refrigerator, find the four screws

on the tops side of the top drawer and the

four on the bottom side of the bottom

drawer. These will be the ones holding the

plastic extrusion into place. Remove the

screws furthest to the outside (4 total, not all

8).

3. Using the “L” bracket included with the

Nucraft hardware kit, place the slotted side

down over the holes that the screws were

removed from. Flush the front of the “L”

bracket (single hole side) to the front of the

refrigerator door and reattach screws. Do

not use the flat brackets included with the

Kitchen Aid refrigerator.

4. Place the two sided tape on the

refrigerator. Locate the top drawer front.

This will be the taller of the two, measuring

16” roughly in height. Keeping an even gap

left to right of the drawer front and flush to

the doors pre-mounted already on the

credenza and sit the front onto the drawer,

using the two sided tape to hold it into place.

“L” bracket at top of top drawer,

please note that for the bottom

drawer, the “L” brackets will be

mounted to the bottom plastic

extrusion. This will give the ability to

create a tighter drawer gap than

Kitchen Aid’s instructions give.

Performance Credenza Kitchen Aid KDDC24RVX KDDO24CVX Custom Drawer Front Nucraft Furniture Company

4

5. Mark the hole locations of the “L”

brackets versus the custom fronts and

measure the custom front overlap on the top

of the drawer.

6. Using the chart on the left hand side,

place pre-drills into the panel

7. Attach clips so that the tabs are to the

outside.

8. Remove tape and slide front onto

drawer.

9. Find the marks created from the “L”

bracket locations. Make sure the face is

located desirably with rest of the credenza; it

still will have some play for adjustment. Pre

drill for the “L” bracket and attach screw to

lock into place.

10. For the bottom drawer, follow the same

steps for the top, except use the bottom of

the drawer to locate the front and the

hardware. Try to keep flush with the bottom

of the case doors, but if needed it can float

above or below to help keep an even gap

between drawers to match gaps in-between

drawers and doors.

Performance Credenza GE Monogram ZIDI240BII Custom Drawer Front Nucraft Furniture Company

2

Before Beginning Installation

• Hardware attached will work in conjunction to refrigerator hardware

• Only GE Monogram ZIDI240WII will work.

• Reference the refrigerator instructions in conjunction with these instructions. Due to the nature and

appearance of the credenza, the size and overlap of the custom fronts will be different then what is

given in the refrigerator manufacturer’s instructions.

• Important to level both fridge and credenza best as possible

• Products pictured may not match particular installation

• Please read all of the instructions prior to beginning the assembly.

Tools Required For Assembly

• Tools needed:

o Level

o Drill

o Phillips bit

o 3/32” drill bit

o Wonder bar or equivalent crow bar

o Tape measure

o Pencil

Hardware

a. #8 x 1” wood screw x 8

b. Two sided tape x 4

c. Two 23 3/16” x 14 11/16” filler panels (raw flake core)

Performance Credenza GE Monogram ZIDI240BII Custom Drawer Front Nucraft Furniture Company

3

Leveling Case & Refrigerator

1. Place credenza to desired location.

There will be eight total glides to the inside

of the toe kick.

2. Level refrigerator, keep in mind only the

front glides will be accessible one it is in

place inside the credenza.

3. Slide the refrigerator inside the

credenza. It should sit about ¾” from flush.

Check the levelness again on the

refrigerator versus the case and make

adjustments if needed.

Installing Custom Fronts

1. Keep in mind, to create the look of the

credenza, the fronts will be larger than the

instructions included with the refrigerator.

2. Per step 2 of the GE directions (page 6),

remove the trim. Insert the custom filler

panels Nucraft has supplied. They will be

different then the GE directions in the fact

that they are single piece with a step to fit

into the trim of the refrigerator drawer vs. the

plied version they show. Do not attach the

custom fronts yet. Reattach the trim.

3. Using rubbing alcohol, clean the front

surface of the inserts and back sides of the

custom fronts. Apply the two sided tape to

the front of the inserts, two per.

4. Locate the top drawer front. This will be

the longer of the two, measuring 16 1/8”

roughly in height. Keeping an even gap left

to right of the drawer front and flush to the

top of the doors pre-mounted already on the

credenza and sit the front onto the drawer,

using the two sided tape to hold it into place.

Top Drawer

Performance Credenza GE Monogram ZIDI240BII Custom Drawer Front Nucraft Furniture Company

4

.

5. With the custom fronts stuck to the

inserts with the correct door gap spacing,

remove the trim.

6. Slide the filler panels out of the trims to

gain access to the back.

7. With the custom fronts still stuck in the

correct place, screw in the #8 x 1” wood

screws through the 4 pre-drills in the filler to

the custom front, securing its placement.

8. Slide the filler panel back into the trim

making sure that that the pull on the custom

front is on the top.

9. Reinstall the side trims per step 2 in GE

instructions.

10. For the bottom drawer, follow the same

steps for the top. Try to keep flush with the

bottom of the case doors, but if needed it

can float above or below to help keep an

even gap between drawers to match gaps

in-between drawers and doors.