Upload
ngohuong
View
213
Download
0
Embed Size (px)
Citation preview
TIER 4FINAL
EXPERTS FOR THE REAL WORLD
SINCE 1842
www.casece.com
F-SERIES COMPACT WHEEL LOADERS
21F I 121F I 221F I 321F
PERFECT IN
EVERY MISSION
2
CASE, MORE THAN 170 YEARS OF INNOVATIONA long history of industry fi rsts
• 1842: Case is founded.
• 1869: First Case portable steam engine - road construction is born.
• 1957: The fi rst factory - integrated loader/backhoe in the world: a Case industry fi rst.
• 1958: The fi rst Case 4-WD wheel loader, the W9.
• 1992: Case expands its wheel loader range with 21B, 121B, 221B and 321B models.
• 1998: Ride control on loader backhoes and skid steer loader: another Case fi rst.
• 2001: The exclusive Cooling Cube in Case wheel loaders means clean engine, reliability and massive bucket payloads.
• 2005: The E-Series compliant with EU Stage IIIA / Tier 3 regulations and with High Travel Speed option is launched.
PERFECT IN
EVERY MISSION
3
Model 21F 121F 221F 321F
Power 58 hp / 43 kW 64 hp / 48 kW 74 hp / 55 kW 74 hp / 55 kW
Torque 251 N.m 255 N.m 308 N.m 308 N.m
LOW EMISSIONSFpt, in-house advanced engine technology
Case equipment features the advanced in-house engine technology
developed by sister company FPT Industrial hat pioneered low emissions,
high effi ciency solutions for on- and off-road applications. With a broad
portfolio of technologies and products, FPT brings to Case customers the
competitive advantage of powertrain technologies that reliably delivers high
performance with low operating costs – proven technologies from a global
engine manufacturer that produces as many as 600,000 engines a year.
• 3.4 liter 4-cylinder Turbocharged Multiple Injection High Pressure
Common Rail Engine with Waste Gate for optimum turbo pressure stability
• EU Stage IIIB / Tier 4 fi nal compliant using Maintenance Free Technology:
- A Diesel Oxidation Catalyst (DOC) that reduces the quantity of
Particulate Matters (PM)
- A PM-Catalyst that traps residual PM
4
FAST ATTACHMENT CHANGE OVER• Hydraulic coupler controlled from the all-in-one joystick
• Depressurized push-pull connectors
FAST TRAVELLING• Engage Turtle/Rabbit speed under load
• 221F and 321F are available in High
Travel Speed (HTS) version: 33 km/h
SHORT TURNING RADIUSMakes your day-to-day job easier when
working in tight spaces.
HIGH PAYLOAD• From 1,9 t up to 2,5 t tipping load
• Auto-Ride Control optimizes bucket retention.
AUTO-RIDE CONTROLride Control, activated only when needed,
over 7 km/h prevents arm bouncing.
8 GOOD REASONS
TO USE IT
5
HIGH VERSATILITYeasy asphalt planing, snow blowing, brooming, compacting and much more with:
• 1 or 2 auxiliary hydraulic circuit
• Creep speed: max fl ow at constant low speed
• High fl ow option on 221F and 321F
• The wide offering of Case attachments
LOW EMISSIONS• EU Stage IIIB / Tier 4 fi nal compliant
• No particulate fi lter
• No fuel injectors in the exhaust
COMFORT CAB• 10 air vents ensure perfect climate control in all seasons
• Control all functions from the joystick
6
GREATER STABILITYOscillating rear axle
The combination of the articulated joint and the rear oscillating axle reduces maximum cab oscillation by 50% or more.
MILLIMETRIC CONTROLInch and brake pedal
It progressively disengages the transmission during the decelerating phase and progressively engages the brakes.
LOW CAB PROFILETake the shortest path
No waste of time with the reduced cab height:
• 21F and 121F: 2.46 m
• 221F: 2.63 m
• 321F: 2.68 m
You can always take the shortest path from point A to point B - in indoor jobs or when transporting on a truck.
PERFECT IN
EVERY MISSION
7
SUPERIOR DUMP HEIGHTCentred and higher loading
The superior hinge pin height and the Case “banana“ arms make it easy to load at the centre
of the trailer without touching the edge with the arms.
HIGH PAYLOAD, HANDLE HEAVIER PALLETS
8
FAST ATTACHMENT CHANGE OVERPlug and unplug your attachment in a few seconds
With the depressurized push-pull connectors you will never need hand tools to swap your attachments.
Front electrical socket
For multi-functioning or special attachments.
Standard fl ow or high fl ow
• Standard Flow (Max pressure: 230 bar):
- 21F-121F: 67 lpm @ 2500 rpm
- 221F-321F: 85 lpm @ 2500 rpm
• The High Flow package is available on 221F-321F:
- 130 lpm @ 2500 rpm
High Flow option always comes as part of a package including Creep Speed, Front electrical socket and Return
Depressurized Drain.
PERFECT IN
EVERY MISSION
HIGH VERSATILITY READY FOR EVERY ATTACHMENT
9
SUPERIOR CAB SAFETYCab structure: rops and fops level 2 come as standard
Designed to protect the operator in case the machine rolls over or a 227 kg rock falls from 5 meters height on the roof.
EASY CAB ACCESSEasy entrance
With low cab fl oor and wide steps.
If you want even more
The Deluxe Option includes an additional storage compartment under you left hand, storage spaces around the seat
and height adjustment of the steering wheel.
ALL-IN-ONE Joystick
Adjustable wrist rest
10 air vents
COMFORT CAB WORK AROUND THE CLOCK
ROPSFOPSLEVEL 2
Tilting adjustment
of the steering wheel
10
THE CASE DEALER: YOUR PROFESSIONAL PARTNERYour success starts with world-class Case machinery and attachments.
Your Case dealer will help you work smarter and faster by selecting equipment that delivers performance and
operator comfort.
Your dealer has the knowledge and experience necessary to help you choose the right attachments so you can…
• Work faster and extend equipment life.
• Increase machine utilization.
• Increase your capabilities.
Let your Case dealer service your machine on the jobsite.
You’ll be back on the job faster.
Advantages include…
• Responsive job site service to keep your equipment running.
• Increase machine uptime.
• Certifi ed service staff and improved parts availability.
11
PARTSWhen you’re looking for superior parts options to maximize the performance and lower the operating costs of your
Case machinery, turn to CNH Industrial Genuine Parts to keep you equipped for success.
CNH Industrial Genuine Parts fi t better, install faster and last longer and in an industry where “high impact” and
“heavy lifting” are the norm, the smallest mechanical differences can lead to big problems.
CNH Industrial Genuine Parts from Case are manufactured from superior materials and specifi cally designed for
Case construction equipment to continually and reliably withstand the punishment of everyday construction. So
steer clear of mechanical problems and future breakdowns, by choosing CNH Industrial Genuine Parts from Case.
They’re the only parts that are fi eld-tested and proven to keep your Case equipment performing its best.
SERVICE. RELY ON CASE TO DELIVER FOR YOUYour commitment to your operation is evident every day, but that doesn’t minimize the enormous pressure you
face to reduce operating costs and improve productivity. So when you’re on the job, make sure you have top-notch
service and support of Case behind you every step of the way.
With our factory trained technicians, you can ensure that top-notch service professionals are working on your
maintenance needs, so you can focus on your business and the big job challenges ahead, not on the tasks of
servicing your equipment.
With your Case Service, you get more than mere oil changes. A Case Service ensures your Case equipment receives
a thorough service that meets all requirements of its service schedules and properly maintains it for the day-in, day-
out punishment of construction work.
Don’t give another thought to time-consuming maintenance tasks. Simply rest easy and make certain that your
service needs are taken care of by a Case factory trained technician.
12
When the unexpected occurs, you need to know your
equipment is protected.
At Case Construction we understand the importance of your
machinery being in good working order when it counts.
ProCover is designed to help keep your equipment working
well beyond the manufacturer’s base warranty period while
taking away the concerns of the cost and inconvenience of
mechanical failure.
WHAT ARE THE ADVANTAGES OF PROCOVER?
PEACE OF MIND
Provides protection beyond the Manufacturer’s Base
Warranty Period.
FLEXIBLE OPTIONS
Plans can be customised to meet individual needs.
DEPENDABLE SERVICE
Eligible repairs completed by an authorised Case
Construction Dealership and their trained service
technician’s using genuine OEM parts & lubricants.
TRANSFERABLE PROTECTION
New Equipment Plans may be transferred to a new
owner at no charge
COVERAGE
• STANDARD
PROTECTION PLAN 3 Years / 3000 Hours
Additional years/hours can be purchased.
Please contact your local Case Construction
dealer for further information.
13
This plan provides coverage for the components listed below when a failure occurs due to a defect in material or
workmanship, and may provide coverage for additional components not listed when the damage is caused by or
resulting from a covered failure of a listed component.
ENGINE AND ALL INTERNAL
LUBRICATED COMPONENTS WITHINTRANSMISSIONS/AXLES/HYDROSTATICS ELECTRICAL HYDRAULICS
Accessory Gears Axle Housing Alternator Accumulator And Related Relief Valve
Air Intake Hose Axle Shaft Gauges Brake Accumulator
Camshaft Clutch Discs (Wet Only) Horn Brake Pressure Sensor
Camshaft Bearings Clutch Plates (Wet Only) Indicators Brake Pump, Brake Valve
Camshaft Drive Gear Control Rods Instruments Differential Lock Valve
Catalytic Converter Counter Shaft Clutch Electronic Joysticks Fan Pumps And Motors
Charge Air Cooler Differential Housing Electric Motors Hydraulic Cylinders
Cold Start Enrichment Systems Differential Pinion Gear / Ring Gear Factory Installed Telematics Hydraulic Hoses and Piping
Connecting Rods & Bearings Drive Axle Hub Sensors Hydraulic Motors
Crankshaft Bearings & Gear Drive Shaft Support Bearing Solenoid Valves Hydraulic Oil Coolers
Crankshaft Including Front And Rear Crankshaft Seals Drive Shaft with Universal Joints Starter And Starter Solenoid Hydraulic Pumps
Cylinder Heads/ Head Gaskets Electronic Transmission Controller and Valve Switches Hydraulic Reservoir
Cylinder Liners Enclosed Oil Immersed Chains and Sprockets Traction Control System Hydraulic Valves
Diesel Exhaust Fluid Tank and Dispensing System External Oil Lines Voltage Regulator Internal O-Rings and Bonded Washers
Diesel Particulate Filter Filler Tubes (Transmission) Wiring Harnesses Pilot Control
EGR System Manifold Final Drive Pinion Wiring Harnesses Exclusions Pressure Reducing Valves
Electronic Engine Control Module Final Drive Planetary Gears Rubbing, Chafi ng, Loose Or Corroded Connections Unloading Valves
Engine Block Front Wheel Drive SensorsFACTORY INSTALLED HEATAND
AIR CONDITIONINGSTRUCTURAL
Engine Mounts And Supports Hydraulic Drive / Travel Motor Accumulator Backhoe Booms
Engine Oil Cooler Hydraulic Drive Pump Clutch Backhoe/Excavator Dipper Sticks
Engine Speed Controls, Linkages, and Cables Hydraulic Transmission-Control Valve Compressor C Frame
Exhaust Manifold and Muffl er Hydrostatic Motor Condenser Car Body
Fan And Fan Drive Hydrostatic Transmission Charge Pump Dryer Chassis
Filter Mount Hydrostatic Transmission Pump Evaporator Circle Frame
Flywheel, Ring Gear Hydrostatic/Hydraulic Pump Drives Expansion Valve Engine Frame
Front And Rear Engine Covers And Seals Internal Lubricated Clutch Housings Heater Core Equipment Frame
Front Damper Internal Transmission Control Linkage Hoses Excavator Booms
Fuel Lines Internal Wet Service Brakes Pulley Falling Object Protection Structure (FOPS)
Fuel TankMFWD Axle/Differential Assembly including
Driveshaft and U JointSeals & Gaskets Forklift Masts
Fuel Transfer Pump & Gasket Planetary Gear Carrier Temperature Control Programmers and ValvesInner and Outer Dipper Arms of the Extendable Boom
(Backhoe Loader)
Injection Pump Pneumatic Valves OPERATOR AREA Main Frame
Injectors Rotary Hydraulic Manifold Covers and Panels Rollover Protection Structure (ROPS)
Intake and Exhaust Manifold And Gaskets Splitter Drive/Drop Box Exterior/Interior Door/Panel Latches, Hinges & Struts Swing Frame
Oil Filler Tube Steering Clutches (Wet) Exterior/Interior Moldings Swing Tower Castings (Backhoe Loader)
Oil Lines Swing Motor And Swing Gear Box Knobs for Switches and Handles Track Frame
Oil Pan And Gasket Torque Converter Mirrors Wheel Loader/Skid steer Loader Arms
Oil Pump Torque Converter Pump Seat Frame & Suspension
Pistons & Rings Transfer Drive
Pre-Cleaner/Air Cleaner Housing Transmission Case
Pressure/Temperature Sensors & Sending Units Transmission Gears, Bearings, & Shafts
Pulleys Transmission Pump
Radiator Travel & Swing Sections (only) Of Main Control Valve
Rocker Arm Assembly Travel Control Valve
Selective Catalytic Reduction System Turntable Bearing
Thermostats Undercarriage Roller And Idler Seals And Bearings
Timing Gears Undercarriage Tensioners
Turbocharger And GasketUNDERCARRIAGE EXCLUSIONS:
Sprocket, Tracks, Pads, Bolts, Chains, Or Any Failure
Due To Wear, Or Breakage Caused By WearValve Cover And Gasket
Water Piping
Water Pumps
STANDARD PROCOVER PLUS PROTECTION PLAN
CONSTRUCTION EQUIPMENT MASTER PARTS SCHEDULE
PREMIER COMPONENTS COVERED
14
TRANSMISSIONHydrostatic 4-wheel Drive Transmission _________________ Travel speed
is proportional to the pressure on the throttle.Speed with standard tyresOperating speed range ________________________________ 0–5 km/hTravel speed range__________________________________ 0–20 km/hOptional High Travel Speed ______________________________ 33 km/h(upon request on 221F and 321F)“Inch & Brake” PedalPower transfer from the transmission to the bucket hydraulics at constant rpm. Optimum speed control at low speed.Optional Creep Speed (upon request on 221F and 321F):Set and adjust travel speed in the 1-5 km/h range, adjust engine rpm for hand-free asphalt planing, snow blowing, brooming.
DIFFERENTIAL CHOICELimited slip front & rear (all models) or Front & rear open diff (21F & 121F) or open with 100% lock on front and rear differentials (221F & 321F)
TYRESStandard21F/121F __________________________________________ 12.5-18221F ______________________________________________ 12.5-20321F ______________________________________________ 14.5-20 More special tyres upon request
BRAKESStandard brakes ___________________________________ disc brake.
Located in hubs for 221F/321F, centre mounted for 21F/121FParking brakes ____________________ disc brake on transmission shaft
STEERINGFully hydraulic center pivot steering.Front and rear wheels follow the same track.Steering angle of 40° to each side.Emergency steering function.
ELECTRICAL SYSTEMVoltage _______________________________________________ 12 VBattery _____________________________________________ 95 A.hAlternator ___________________________________________120 A.h
CAPACITIESDiesel ________________________________________________ 87 lEngine oil ______________________________________________ 7 lCooling liquid ___________________________________________ 16 lTotal hydraulic oil ________________________________________ 57 lFront axle ______________________________________________ 9 lRear axle ______________________________________________ 12 l
HYDRAULICSGear pump for loading and steering hydraulicsPriority valve favouring steering hydraulics3rd or 4th functions are proportionally controlled by the All-in-one Joystick with, Flow memory button as standard.Standard Flow 21F-121F _________________________________ 67 lpm @ 2500 rpm 221F-321F ________________________________ 85 lpm @ 2500 rpmHigh Flow packageavailable upon request on 221F-321F ____________ 130 lpm @ 2500 rpm
NOISE AND VIBRATIONSExternal - Guaranteed acoustic power-level LWA (1) _____________ 101 dBCab interior - Sound Pressure Level (2) 21F-121F: ______________ 71 dB
221F-321F: _____________ 72 dBHand- / arm- / body -vibration (3) ___________________ < 2.5 / 0.5 m/s²(1) According to 2000/14/EG & appendixes.(2) According to ISO 6396.(3) According to ISO 8041
EMISSIONSNox + HC ________________________________________ 4.5 g/kW/hCO ____________________________________________ 0.10 g/kW/hPM ____________________________________________ 0.02 g/kW/h
EASY PALLET LOADING Linkage: Mechanical self-levelling on XT and Z-bar.
XT is the best linkage for pallet handling. Visibility on the pallet is the best with one lifting cylinder only and payload is optimum
Z-BAR is the most versatile linkage type. It offers more breakout force thanks to the 2 lifting cylinders and a higher dump height.
F-SERIES
COMPACT WHEEL LOADERS
15
GENERAL DIMENSIONS
21F 121F 221F 321F
H1 2.46 m 2.46 m 2.63 m 2.68 m
H2 45 cm 45 cm 44 cm 49 cm
W1 1.74 m 1.74 m 1.80 m 1.86 m
W2 1.90 m 2.05 m 2.05 m 2.10 m
L1 2.08 m 2.08 m 2.22 m 2.23 m
R 3.72 m 3.72 m 3.99 m 3.99 m
SPECIFICATIONS WITH BUCKET
AB
C
L
D
E
45°
21F 121F 221F 321F
Z-BAR XT Z-BAR XT Z-BAR Z-BAR
Bucket Volume (SAE) 0.7-1.0 m3 0.9 -1.1 m3 1.0 - 1.2 m3 1.1 - 1.2 m3
Tipping load straight 3.9 t 3.8 t 4.1 t 4.1 t 4.2 t 4.6 t
Tipping load at full turn (40°) 3.2 t 3.3 t 3.3 t 3.5 t 3.6 t 3.7 t
Payload @50% 1.6 t 1.6 t 1.7 t 1.8 t 1.8 t 1.9 t
Breakout Force 5925 daN 4024 daN 5375 daN 3849 daN 6269 daN 6194 daN
L2 Length with bucket 5.28 m 5.23 m 5.39 m 5.33 m 5.62 m 5.68 m
A Max bucket height 3.14 m 3.94 m 3.18 m 4.09 m 3.29 m 3.40 m
B Hinge pin height 3.14 m 3.11 m 3.18 m 3.13 m 3.29 m 3.40 m
C Dump height @45° 2.49 m 2.34 m 2.52 m 2.35 m 2.60 m 2.69 m
D Dig Depth 7.3 cm 13 cm 12 cm 14 cm 10 cm 8.4 cm
E Reach at full height 77 cm 71 cm 83 cm 74 cm 85 cm 85 cm
Operating weight (std. bucket) 5115 kg 5015 kg 5423 kg 5208 kg 5694 kg 6195 kg
Operating weight (4-in-1 bucket) 5414 kg 5304 kg 5742 kg 5507 kg 6034 kg 6535 kg
SPECIFICATIONS WITH FORKS
F BG2
G1
J2
J3
J1* on even ground, according to ISO 8313 and EN 474-3
21F 121F 221F 321F
Z-BAR XT Z-BAR XT Z-BAR Z-BAR
Tipping load straight 2.8 t 3.0 t 3.0 t 3.2 t 3.1 t 3.6 t
Tipping load at full turn (40°) 2.4 t 2.6 t 2.6 t 2.8 t 2.7 t 3.0 t
Payload @80%* 1.9 t 2.1 t 2.1 t 2.2 t 2.2 t 2.5 t
F Max overall height 3.48 m 3.63 m 3.53 m 3.65 m 3.63 m 3.73 m
B Hinge pin height 3.14 m 3.11 m 3.18 m 3.13 m 3.29 m 3.40 m
G2 Max fork height 2.90 m 2.96 m 2.95 m 2.97 m 3.08 m 3.19 m
G1 Forks height @ max reach 1.27 m 1.34 m 1.27 m 1.34 m 1.34 m 1.39 m
J1 Reach @ ground level 0.94 m 0.77 m 1.01 m 0.80 m 0.99 m 0.99 cm
J2 Max Reach 1.35 m 1.26 m 1.41 m 1.27 m 1.43 m 1.43 cm
J3 Reach @ max height 0.59 m 0.46 m 0.63 m 0.47 m 0.61 m 0.61 m
Operating weight with forks 5020 kg 4910 kg 5310 kg 5090 kg 5559 kg 6060 kg
SPECIFICATIONS
EXPERTS FOR THE REAL WORLD
SINCE 1842
www.casece.com
CustomerCCACCssistanc
CustomestoCAAC
ecc
1300 99 CASE
NOTE: CASE provides specifi c outfi ts for various countries and manyoptional fi ttings (OPT). The illustrations on this or other leafl ets mayrelate to standard or optional fi ttings. Please consult your CASEdealer for any information in this regard and any possible updating on components. CNH Industrial reserves the right to modify machine specifi cations without incurring any obligation relating to such changes.
CASE CONSTRUCTION EQUIPMENT
CONTACT INFORMATION
AUSTRALIA
31-53 Kurrajong Road
St. Marys nsw 2760
Form No. ANZ4401CCGB - Print in Australia - MediaCross Firenze - 06/15