- Tube Solutions subsidiary of To find out how you can participate in the ... Max Round Tube Mild Steel mm 18 x 2 38.1 x 2 50.8 x 3 63 x 3 80 x 3 89 x 6 114 x 8

Volume 2/06

www.tubemart.comA subsidiary of

To find out how you can participate in the TubeMartTM

programme, please call + 44 (0) 1772 771556or email: [email protected] 188 Bradkirk Place, Walton Summit, Bamber Bridge Preston, Lancashire United Kingdom PR5 8AJ.

Tel: +44(0)1772 771556 Fax: +44(0)1772 323227 Email: [email protected] Web: www.tubemart.com

Welcome to TubeMartTM – the new, single source way to select all your

high quality, mid-range tube manipulation solutions at exceptionally

competitive prices.

Bringing together the widest choice of hand-picked machinery from many of the world’s

premier manufacturers into one highly comprehensive catalogue, TubeMartTM redefines

the way you select machinery.

Built to uncompromising international standards, as laid down by world-leading tube

manipulation specialists, AddisonMckee, all TubeMartTM models are available globally

through our international team of dealers.

With bending, cutting, end-forming, notching and polishing technologies – as well as

a comprehensive range of consumables – selecting the tube manipulation solutions

you require has never been quicker or easier.

This TubeMartTM catalogue has been issued in good faith (errors and omissions

excepted). We do trust that sufficient information to select the machine for your

production requirements are supplied.

Information in the catalogue is not binding in detail and in pursuit of excellence,

TubeMartTM retain the right to change specifications and form without prior notice.

Machines are shown without safety covers and protection devices to enable the

showing of more detail.

Every TubeMartTM machine carries our unique Quality Assured symbol – your

guarantee that it has been designed and built to the very highest standards as laid down

by TubeMartTM – and offers exceptional levels of quality, precision and reliability.

TubeMartTM Head Office in Ohio, USA

www.tubemart.comwww.tubemart.com

TubeMartTMTubeMartTM

Bend

ing

Cutt

ing

Not

chin

gPo

lishi

ngEn

dFi

nish

ing

Cons

umab

les

Introduction Contents2 Bending4 Mandrel Tube and Profile Benders14 Double Head Tube and Profile Benders16 Tube and Profile Rollers

48 End Finishing50 Tube End Forming52 Tube Tapering53 Tube and Bar Chamfering53 De-Burring

54 Consumables56 Lubricants58 Saw Blades59 Mandrel and Wiper Die Selection Guide60 Ordering Tooling

44 Polishing46 Bend Tube Polishing47 Straight Tube Polishing

20 Cutting22 Circular Saw Blade Cutting30 Aluminium Cutting33 Band Saw Cutting36 Supported Shear Cutting

40 Notching42 Tube End Notching

Page Section

TubeMartTM | BendingTubeMartTM | Bending |32|

Bend

ing



Standard Features

• Anticipated mandrel retraction unit

• Mandrel lubrication unit

• Powered follower slide

• Water hydraulic cooler

• Safety systems

Optional

• Bend tooling

High performance single axis programmablehydraulic mandrel tube benders. Ideal forless-complex, often high volume productionrequirements demanding good bend quality.Bend angle is easy to programme and the clamp, pressure slide and mandrel arePLC controlled.

OverviewVery easy to programme and perform mandrel bends.Cycle would be as follows: Insert tube over the mandrelto a pre-set stop. Step on foot switch, clamp and pressure die comes in. Tube is bent to the pre-programmed angle. Mandrel retracts, clamp andpressure die opens. Operator removes the bent tube from the bend die. Operator steps on the foot switch, the bend die returns to zero and the mandrel moves forward. Ten bends can be pre-programmed and performed in sequence.

PNCB Single Axis Tube and Profile Benders

SPECIFICATION UNIT PNCB18 PNCB40 PNCB52 PNCB65 PNCB80 PNCB90 PNCB115

Max Round Tube Mild Steel mm 18 x 2 38.1 x 2 50.8 x 3 63 x 3 80 x 3 89 x 6 114 x 8

Non Ferrous mm 20 x 2 38.1 x 4 50.8 x 5 63 x 6 80 x 6 89 x 9 114 x 10

Stainless Steel mm 19 x 0.8 38.2 x 1.2 50.8 x 1.8 63 x 2 80 x 1.8 89 x 4 114 x 5

Square Tube Mild Steel mm 15 x 15 x 1.2 30 x 30 x 2 40 x 40 x 2.5 50 x 50 x 2 60 x 60 x 2 75 x 75 x 2 100 x 100 x 3

Solid Bar mm 8 20 25 30 40 50 60

Min/Max Bending Radius mm 10 ~ 80 25 ~ 200 35 ~ 250 50 ~ 300 50 ~ 350 50 ~ 450 50 ~ 450

Spindle Diameter mm 20 40 45 55 60 100 120

Clamp Stroke mm 40 50 65 90 90 100 125

Pressure Slide Stroke mm 50 50 65 90 90 100 125

Follower Slide Stroke mm 118 310 410 360 500 620 650

Mandrel Stroke mm 40 80 80 160 200 200 200

Max Bend Angle Deg 190 190 190 190 190 190 190

Max Length Over Mandrel mm 2000 3000 3000 3000 3150 3200 3200

Working Height mm 900 950 950 1000 1100 1140 1200

Tooling Centreline Height mm 44 31 41 50 65 100 110

DOB (Bending Speed) Deg/Sec 150 65 44 24 16.5 10 10

Accuracy of DOB +/- Deg 0.3 0.3 0.3 0.3 0.3 0.3 0.3

Hydraulic Motor Kw 1.5 4 5.5 7.5 11 15 18.5

Total Power Kw 1.5 4 5.5 7.5 11 15 18.5

Hydraulic Pressure Bar 80 120 120 140 140 140 140

Hydraulic Tank Capacity L 60 150 160 175 220 250 300

Machine Length mm 2950 3500 3100 3700 4350 4460 4500

Machine Width mm 500 750 800 950 1100 1300 1350

Machine Height mm 1200 1200 1200 1200 1300 1300 1300

Machine Weight Kg 500 750 1400 2000 3000 4400 4500

PNCB18

PNCB90

PNCB40

PNCB52

PNCB80

Anticipated mandrelretraction unit

Straight acting clamp

Bend

ing


Bend

ing


Standard Features





• Rise and fall clamps

• Safety systems

Optional

• Bend tooling

• Left hand bending (L)

OverviewVery easy to programme through a touch screen PLCcontrol with graphic guidance to perform mandrelbends. Cycle would be as follows: Insert tube over themandrel into the collet. Move carriage manually back to the first stop. Step on foot switch, clamp and pressure die comes in. Tube is bent to the pre-programmed angle. Mandrel retracts, clamp and pressure die opens. Operator moves the carriagemanually to the next stop, the bend die returns to zero,the B axis rotates to the pre-programmed angle and the mandrel moves forward and the cycle repeats itself.Ten bends can be pre-programmed and performed insequence. 100 programmes with ten bends each can be saved in the memory.

PNCPB Two Axis Hydraulic Tube and Profile Benders

PNCPB40

PNCPB52

PNCPB65

PNCPB80 L

Two axis NC tube benders with B (Rotation) andC (Bending) under NC control. Ideal for lowvolume work where CNC accuracy is required.

Rise and fall clamp system

SPECIFICATION UNIT PNCPB18 PNCPB40 PNCPB52 PNCPB65 PNCPB80

Max Round Tube Mild Steel mm 1.8 x 2 38.1 x 2 50.8 x 3 63 x 3 80 x 3

Non Ferrous mm 20 x 2 38.1 x 4 50.8 x 5 63 x 6 80 x 6

Stainless Steel mm 19 x 0.8 38.2 x 1.2 80.8 x 1.8 63 x 2 80 x 1.8

Square Tube Mild Steel mm 15 x 15 x 1.2 30 x 30 x 2 40 x 40 x 2.5 50 x 50 x 2 60 x 60 x 2

Solid Bar mm 8 20 25 30 40

Min/Max Bend Radius mm 10 ~ 80 25 ~ 200 35 ~ 250 50 ~ 300 50 ~ 350

Spindle Diameter mm 20 40 45 55 60

Clamp Stroke mm 40 50 118 110 90

Pressure Slide Stroke mm 50 50 65 90 90

Follower Slide Stroke mm 118 300 410 360 500

Mandrel Stroke mm 40 80 80 160 200

Max Bend Angle Deg 190 190 190 190 190

Max Length Over Mandrel mm 2000 3200 3000 3000 3000

Working Height mm 1100 1000 1000 1000 1100

Tooling Centreline Height mm 44 45 45 55 65

DOB (Bending Speed) Deg / Sec 150 65 44 24 16.5

Accuracy of DOB +/- Deg 0.3 0.3 0.3 0.3 0.3

POB (Rotation Speed) Deg / Sec 160 140 140 70 60

Accuracy of POB +/- Deg 0.3 0.15 0.15 0.15 0.3

Hydraulic Motor Kw 1.5 4 5.5 7.5 11

Total Power Kw 1.5 4.5 6 8 11

Hydraulic Pressure Bar 80 120 120 140 130

Hydraulic Tank Capacity L 60 150 160 175 220

Machine Length mm 3000 3900 4800 4900 5900

Machine Width mm 800 750 750 900 1100

Machine Height mm 1450 1200 1200 1300 1300

Machine Weight Kg 1200 2000 2800 3000 3000



Standard Features





• Rise and fall clamps

• Safety systems

Optional

• Bend tooling

OverviewVery easy to programme and perform multiple mandrel bends with repeatedaccuracy on small to medium production runs. Cycle would be as follows:Insert tube over the mandrel into the collet. Step on foot switch, the colletcloses and the DBB axis pulls the tube into the first programmed position. The mandrel goes forward and the clamp and pressure die comes in. Tube is bent to the pre-programmed angle. Mandrel retracts, clamp and pressure die opens. The machine moves forward in the DBB (Y) axis, the POB (B) axis rotates and the next bend DOB (C) is made in the tube.Operator removes the bent tube from the bend die. Operator steps on the footswitch, the bend die returns to zero and the mandrel moves forward. Ten bends per component can be pre-programmed. 30 bends x 1000 partsstorage optional.

PSRH Three Axis Automatic Hydraulic Tube Benders

PSRH40

PSRH18

Full automatic cycle NC mandrel tube bender for tubes and profiles. Easy programming,setup and total flexibility makes this machine ideal for Jobbing shops with small to medium production volumes.

SPECIFICATION UNIT PSRH18 PSRH40

Max Round Tube Mild Steel mm 18 x 1.2 38.1 x 2Non Ferrous mm 20 x 2 38.1 x 6Stainless Steel mm 18 x 0.8 38.1 x 1.2Square Tube Mild Steel mm 15 x 15 x 1.2 30 x 30 x 2.5Solid Bar mm 8 20Min/Max Bend Radius mm 10 ~ 80 30 ~ 170Spindle Diameter mm 20 40Clamp Stroke mm 40 100Pressure Slide Stroke mm 50 55Follower Slide Stroke mm 118 350Mandrel Stroke mm 40 70Max Bend Angle Deg 190 190Max Length Over Mandrel mm 2000 3000Working Height mm 1100 1120Tooling Centreline Height mm 22 45DOB (Bending Speed) Deg / Sec 250 65Accuracy of DOB Deg 0.1 0.1DBB (Feeding Speed) mm / Min 2300 1200Accuracy of DBB mm 0.1 0.1POB (Rotation Speed) Deg / Sec 320 220Accuracy of POB Deg 0.1 0.1Hydraulic Motor Kw 2.2 5.5Total Power Kw 4.35 6Hydraulic Pressure Bar 70 140Hydraulic Tank Capacity L 80 200Machine Length mm 3650 4800Machine Width mm 800 1000Machine Height mm 1400 1250Machine Weight Kg 900 2000

Bend

ing



Standard Features

• Allen-Bradley control

• Allen-Bradley drives and motors

• Rexroth hydraulics

• Foot pedal start

• 22mm dia mandrel rod

• Drop down clamp



• Safety scanner and barrier rail

• Operator and technical manuals

Optional

• Bend tooling

PB Heavy Duty CNC Hydraulic Tube Benders

PB 75

PB 100

High performance draw bending machines, designed for the accurateand repeatable bending of tubular components. The TubeMartTM PB rangecombines years of proven design techniques with lower manufacturingcosts to provide levels of accuracy, repeatability quick tool change andease of operation as required by today’s manufacturing industries.

SPECIFICATION UNIT PB42 PB75 PB100 PB130 PB150

Maximum Outside Diameter mm 42 76 102 127 150

Minimum Outside Diameter mm 10 20 20 40 50

Maximum Wall Thickness (Carbon Steel) mm 2.0 3 2.0 2.0 2.0

Maximum Centre Line Radius mm 200 250 250 350 400

Minimum Centre Line Radius mm 20 25 35 45 50

Maximum Bend Arm Rotation deg 193 193 193 193 193

Maximum Tube Length Over Mandrel mm 3000 3000 3000 3000 3000


Tooling Centre Line Height mm 40 50 70 95 112.5

Mandrel Strike mm 100 150 300 300 350

Follower Stroke mm 400 450 500 750 800

Reaction Stroke mm 70 100 170 170 190

Hydraulic Tank Capacity Litres 400 500 530 530 550

Hydraulic System Pressure Bar 130 140 140 140 140

Length Rearwards mm 4700 4900 5500 6000 7320

Bend Arm Radius mm 800 800 1000 1250 1500

Length Forwards mm 80 150 250 300 320

Overall Width mm 1400 1650 1650 1950 3000

Height mm 1370 1500 1750 1850 2100

Weight Kg 4000 4500 7500 8000 12500

Bend

ing

Rise and fall clamp system


Bend

ing


PBSTP Four Axis CNC Tube and Profile Benders

SPECIFICATION UNIT PB 42 STP PB 76 STP

Round Tube / Mild Steel (S=40kgf/m2) mm 42 x 2.5 76 x 2.5

Round Tube / Non-Ferrous (S=25kgf/m2) mm 42 x 3.0 76 x 3.0

Round Tube / Stainless (S=60kgf/m2) mm 42 x 1.2 76 x 1.2

Square Tube / Mild Steel (S=40kgf/m2) mm 30 x 1.8 50 x 1.8

Solid Bar / Mild Steel (S=40kgf/m2) mm 20 30

Max. Bending Radius mm 25 ~ 200 25 ~ 250

Max. Bending Angle deg 193 193

Max. Rolling Radius mm 7D 7D

Max. Length over Mandrel mm 3000 3000

Working Height mm 1040 1015

Tooling Centre Line Height Bottom Stack mm 40 50

Tooling Centre Line Height Top Stack mm 120 150

DOB (Bending) Speed deg / Sec 132 80

Accuracy of DOB (Bending) deg ±0.1 ±0.1

DBB (Feeding) Speed mm / sec 1165 1000

Accuracy of DBB (Feeding) mm ±0.1 ±0.1

POB (Rotation) Speed deg / sec 360 300

Accuracy of POB (Rotation) deg ±0.1 ±0.1

Y Axis Push Force kN 5 10

Total Power kVA 14 38

Max. Pressure kgf / cm2 130 140

Hydraulic Tank Capacity Litre 400 530

Machine Length mm 4780 5350

Machine Width mm 1400 2330

Machine Height mm 1370 2100

Machine Weight kg 4000 5000

PB 42 STP


Bend

ing


DH Double Head Compression Tube and Profile Benders

SPECIFICATION UNIT DH25 DH25P DH38 DH38P DH40 DH40P

Max Round Tube Mild Steel mm 1 x 25 x 2 1 x 25 x 2 1 x 38 x 2 1 x 38 x 2 1 x 40 x 2 1 x 40 x 2

mm 2 x 19 x 1.5 2 x 19 x 1.5 2 x 25 x 1.5 2 x 25 x 1.5 2 x 28 x 1.5 2 x 28 x 1.5

mm 3 x 13 x 1.5 3 x 13 x 1.5 3 x 16 x 1.5 3 x 16 x 1.5 3 x 19 x 1.5 3 x 19 x 1.5

mm 4 x 13 x 1.5 4 x 13 x 1.5 4 x 15 x 1.5 4 x 15 x 1.5

Min / Max Bend Radius mm 26 ~ 110 26 ~ 110 38 ~ 200 38 ~ 200 38 ~ 200 38 ~ 200

Spindle Diameter mm 30 30 40 40 40 40

Clamp Stroke mm 35 35 55 55 55 55

Pressure Slide Stroke mm 35 35 55 55 55 55

Max Bend Angle Deg 185 185 185 185 185 185

Min / Max Distance Between Heads mm 140 ~ 1100 140 ~ 1100 170 ~ 1800 170 ~ 1800 200 ~ 1650 200 ~ 1650

Working Height mm 1050 1200 1050 1220 1150 1260

Tooling Centreline Height mm 29.25 29.25 32.5 32.5 42.5 42.5

DOB (Bending Speed) Deg / Sec 80 80 50 50 65 65

Accuracy of DOB +/- Deg 0.3 0.3 0.3 0.3 0.3 0.3

Hydraulic Motor Kw 4 4 5.5 5.5 5.5 5.5

Total Power Kw 4 4 5.5 5.5 5.5 5.5

Hydraulic Pressure Bar 120 120 120 120 120 120

Hydraulic Tank Capacity L 72 72 120 120 150 120

Machine Length mm 1500 1500 2700 2700 2700 2700

Machine Width mm 900 900 900 900 1000 900

Machine Height mm 1250 1400 1350 1450 1400 1500

Machine Weight Kg 750 820 1200 1300 1500 1600

DH25

DH38P

DH40P

DH38



Tube Rolling

TM 35

TM 70

TM 45

TM 65 TM 110

TM 125TM 35M

TM 50H

SPECIFICATION UNIT TM35M TM50H

Max Round Tube Mild Steel mm 38 x 1.5 50 x 1.5

Min Bend Radius mm 200 350

Bending Speed mm / Sec 80 80


Motor Kw 2.2 4

Total Power Kw 2.2 4




Machine Weight Kg 800 1200

Bend

ing


Bend

ing


PROFILE TM30 TM35 TM45 TM65 TM75 TM85mm min ø mm min ø mm min ø mm min ø mm min ø mm min ø Rolls40x5 400 50x5 850 50x5 600 30x30x3 125 70x6 1000 35x35x3 250 AD

25x3 350 50x50x5 250 40x5 500 70x70x8 60060x60x6 500 80x80x8 800

40x5 500 50x5 1200 45x5 600 30x30x3 200 70x6 1400 40x40x4 300 AD25x3 400 40x40x5 300 40x5 500 70x70x9 500

50x50x6 500 80x8x8 100050x6 800 50 650 50 600 30x30x3 150 100 1000 70x30x4 200 AD

60x60x7 300 70x70x8 50080x40x7.5 500 80x80x8 700

50 850 50 900 50 600 30x30x3 150 70 900 30x30x4 200 AD50x50x6 300 70x70x8 50070x35x6 500 80x80x8 700

50 800 50 750 50 600 20x10 100 80 800 40x10 150 AD50x12 200 80x15 25060x15 250 80x20 350

50x10 800 60x10 800 60x10 800 50x5 100 60x15 900 50x10 130 A50x12 800 20x10 300 80x16 200 40x10 600 80x20 200

80x20 600 120x30 30080x15 700 120x15 750 80x15 600 15 150 120x25 600 30 150 A

30 300 40 25035 700 45 500

30x30 700 35x35 1200 32x32 700 20 150 50x50 800 35 150 A20x20 400 35 300 50 250

40 400 60 50030 700 35 800 35 700 25x1.5 100 50 700 40x2 200 B

60x2 400 100x2 120070x2 800 100x3 1500

60x2 1200 70x2 1200 60x2 1000 26.5x2.3 100 100x2 1800 48.3x3.2 200 B15x1 350 48.3x2.9 300 35x2 500 88.9x3.2 500

60.3x3.2 500 88.9x4 80038.1 900 33.7x2.65 320 60x2.9 1000 30x15x1.5 150 88.9x3.2 1500 50x25x2 300 B

9.5x2 300 60x30x2.5 1000 33.7x2.6 500 80x40x5 100080x30x3 3000 100x40x3.21500

50x30x3 50x40x3 60x30x3 20x20x2 120 80x40x3 40x40x2.7 250 B50x50x2.5 800 70x70x3.2 80060x60x3 2000 70x70x4 1500

40x40x3 60x60x3 45x45x3 30x15x4 150 70x70x3.2 60x30x6 200 B60x30x6 200 120x55x6 40080x45x6 400 140x60x7. 600

UNP 50 400 UNP 60 550 UNP 80 800 30x15x4 150 UNP 120 600 60x30x6 200 B50x25x5 250 120x55x6 40080x45x6 500 140x60x7.5 600

UNP 50 500 UNP 60 700 UNP 80 1200 UNP 120 1200 INP 120 250 B

100x50 700 B

Power Kw 0.75 1.5 1.5 + 0.75 2.2 + 0.75 2.2 + 1.1 4 + 0.75Rolls ø mm 137/132 155 162/152 177 215 245Shaft ø mm 35 50 50/40 60/50 70/60 80/70Bending Speed 2.1 m/min 4.3 m/min 3.3 m/min 5.5 m/min 5 m/min 6.5 m/minWeight kg 185 400 500 980 1430 2000W x L x H mm 670x530x1350 730x830x1350 780x950x1450 1020x1150x1050 980x1550x1780 1300x1400x1350

PROFILE TM110 TM125 TM185 TM245 TM300 TM365mm min ø mm min ø mm min ø mm min ø mm min ø mm min ø Rolls50x6 350 120x15 1300 150x15 1000 160x20 1600 200x28 2000 200x28 1600 AD90x8 500 50x5 650100x1050x6 400 100x12 1100 130x15 1200 150x20 1600 200x20 2000 200x28 1800 AD80x8 600 50x5 650100x10 80040x40x4 250 120 1200 150x15 1200 160x20 1400 200x28 1800 200x28 1500 AD80x80x8 350100x100x10 60040x40x4 250 100 1200 130x15 1700 150x20 2000 200x20 2000 200x30 2300 AD80x80x8 350100x100x10 500

130 1300 150x15 1300 160x20 1500 200x20 1800 200x20 1800 AD

40x6 200 125x5 1250 155x30 1000 175x40 1200 200x60 1800 400x60 3000 A100x20 400 40x80 400100x25 80060x10 200 200x50 1000 250x40 1000 350x50 900 300x80 1000 650x100 2000 A100x40 300200x35 50030 200 75x75 800 90x90 1200 110x110 1500 135x135 1200 240x240 2500 A50 25060 50020 200 85 900 100 1000 125 1200 160 2000 260 2000 B60 30070 40040x2 300 160x4 3000 180x4 4000 220x5 5500 320x5 10000 B120x2 1000 50x2 500140x3 150060.3x3.2 200 5 1600 168.3x5.4 2000 193.7x7 2500 273x7.1 4200 508 15000 B114.3x3.6 500114.3x4.5 80040x20x2 300 140x50x5 180x70x8 200x75x8 230x100x10 450x200x10 B100x50x5 1500140x40x3 200050x50x3 250 90x90x8 120x8 150x8 180x10 400x400x16 B90x90x4 1200100x100x5 150040x35x5 200 UNP 220 1000 UNP 300 1200 UNP 360 1200 UNP 450 2000 UNP 1000 4000 B180x70x6 400200x75x8.5 60040x35x5 200 UNP 22 1200 UNP 300 1200 UNP 360 1400 UNP 450 2000 UNP 1000 4000 B180x70x6 400200x75x8.5 600INP 80 300 INP 200 1000 INP 300 1200 INP 360 1500 INP 450 2000 INP 1000 5000 BINP 200 400

A 140 1200 A 180 1100 A 240 1500 A 280 2000 A 1000 6000 BCB 120 1300 B 160 1100 B 200 1500 B 260 2000 B 1000 8000

100x50 8000 UNP 160 1000 UNP 200 11000 UNP 240 13000 UNP 400 40000 BC

INP 120 INP 140 3000 INP 160 4000 INP 200 5500 INP 240 10000 INP 550 20000 BCINP 140

A 120 3500 A 120 4500 A 180 5500 A 200 8000 A 550 40000 BCB 120 2800 B 120 3500 B 160 4000 B 180 8000 B 500 30000

Power Kw 11 15 15 30 64 70Rolls ø mm 315 390 460 550 740 800Shaft ø mm 100 120 180/160 240/220 300/280 360/360Bending Speed 5m/min 7 m/min 7 m/min 0-7 m/min 0-7 m/min 0-7 m/minWeight kg 3500 4500 9000 14000 24000 47000W x L x H mm 1520x1800x1600 1700x1800x1700 2000x2400x1600 2240x3360x2055 3100x3550x2550 5000x5500x3150


TubeMartTM | CuttingTubeMartTM | Cutting |2120|


Cutt

ing

Cutt

ing


CH-90 Fully Automatic Circular Sawing MachineSPECIFICATION UNIT CH-90

Power Saw Feed kW 3

Power Feed Motor kW 0.37

Hydraulic Pump kW 0.75

Bundle Loader kW 1.3

Air Consumption N1 / Cycle 6

Electrical Supply PH-V-Hz 3-400-50

Dimensions H x W x D mm 1475 x 8900 x 2050

Weight kg 3500

Start Tube Length mm 6500

Capacity Round Tubes mm min 10 max 90

Capacity Square Tubes mm min 12 x 12 max 80 x 80

Capacity Rectangular Tubes mm min 15 x 10 max 90 x 70

Saw Blade mm min 160 max 315

Blade Frame and Pins mm 40 4 x 12/64

CH-90

The TubeMartTM CH-90 Fully Automatic Circular sawing machine is an economically pricedmodel that is ideally suited to smaller production runs due to its simple, flexible andergonomic design. The horizontal vice enables clamping of round, square and rectangularsections, with the option of shell jaws for thin-walled tubes.

Roller feed system and viceThe roller feed system transports the tubeswith high speed to the material length stop.The machine is supplied with the facility toprogram a deceleration point so that thetube is under control as it makes the lengthstop, guaranteeing accurate and consistentcut lengths.

Unique bundle loaderThe bundle loader automatically separatesthe material and preloads the magazine forall tubes and symmetrical sections.

Operator friendly control panelThe CH-90 features text control panel isergonomically positioned at eye level on amovable pendant.

The display includes items such as saw blade speed, parts counter, electronic bladeprotection, adjustable machine parameters,blade life counter and error memory. All functions are easy accessible.

Centralised hand wheelQuick adjustment of tube diameters on thebundle loader.

Machine frame and cutting headThe heavy duty helical geared cutting headis mounted on a rigid machine frame. Both the cutting head and vice are easilyaccessible for replacing the saw blade.

Length stop and discharge systemThe length stop is mounted on a precisionrail to provide stability and accuracy. Each stop offers a graduated scale and0.1mm fine adjustment. The unique tiltingtable discharge system automatically separates the trim cut and scrap end fromthe cut component, as well as offering the choice of three discharge positions,either to the front, to the back or to thebottom – (for short lengths only).



Semi-Automatic Circular Saw Blade Cutting

SPECIFICATION UNIT PO 275 NCP PO 315 NCP PO 350 NCH

Cutting Capacity Deg 90 90 90

Clamp / Feed / Cut System Pneumatic Pneumatic Hydraulic

Tube - Round mm 80 95 115

Tube - Square mm 75 x 65 85 x 85 110 x 110

Tube - Rectangular mm 75 x 35 80 x 40 150 x 90

Solids - Round mm 38 55 60

Solids - Square mm 38 x 38 50 x 50 60 x 60

Max Clamp Opening mm 85 110 150

Max Feed Stroke mm 700 700 700

Blade Diameter mm 250 / 275 250 / 275 / 300 300 / 325 / 35

Blade Centre Hole Diameter mm 32 32 32

Drive Pins Diameter and PCD mm 10 x 63 10 x 63 10 x 63

Cutting Speed Rpm 45 / 90 42 / 80 26 / 50

Motor Kw 1.3 / 1.8 1.8 / 2.4 2.4 / 3

Machine Length mm 1800 1880 2400

Machine Width mm 720 730 980

Machine Height mm 1320 1320 1850

Machine Weight Kg 800 850 1000

PO 315 NCP

PO 350 NCH

PO 275 NCP

Manual loading with automatic feeding, clamping and sawing. Ideal forcutting short lengths of tubes, bars and profiles.

Standard Features

• Feeding unit

• Hydraulic / pneumatic clamping

• Stable down feed of the cutting head on linear guide railsNCH Model only


Cutt

ing


SPECIFICATION UNIT UCM 425 UCM 425-LH RCM 425

Saw Blade mm 425 max 425 max 425 max

Cutting Speeds 10 available m / min 14 - 220 14 – 220 22 – 145selectable electrically / mechanically

Swivelling Range Grad 90 – 0 – 90 90 – 0 – 90 Straight cut only

Cutting Range according to diagram according to diagram ø 145 max

Motor kW 5,5 5,5 7,5

Operating Voltage V 3 x 400 V, 50Hz 3 x 400 V, 50Hz 3 x 400 V, 50Hz

Control Voltage V DC 24 24 24

Machine Length mm 460 460 900

Machine Width mm 1440 1440 1360

Machine Height mm 1770 1770 2000

Machine Weight Kg 950 900 950


UCM 425

Universal circular metal up cut saw for cutting solid

materials, pipes, tubes and profiles with a minimum

of burrs. Equipped with one vertical and two

horizontal clamping cylinders with long and short

stroke design as standard.

UCM 425-LH / RCM 425

High-end circular metal saw for cuttings on

straight or bend tubes.

Standard Features – RCM 425

• Pressure reduction – feeding speed controller

• Micro-metring system

• Vertically long stroke cylinder with continuouslystroke-adjustment and fast closing speed

• Heavy diagonally spur gear

• Continuous cutting speeds with digital display

• Micro-metring system for blade lubrication

• Saw pressure reduction

• 2 hand control with security-relay

• Programmable saw blade stroke

• 4 Kw brake-motor for saw drive

UCM 425-LH

RCM 425

Standard Features – UCM 425-LH

• Pressure reduction – feeding speed controller

• Separate hydraulic system

• Vertically long stroke cylinder with continuously stroke-adjustmentand fast closing speed

• Turnable saw-table for 90º cuts for the support from clamping devices

• Heavy diagonally spur gear

• Clamping pressure reduction

• 2 hand control with security-relay

Optional

• Micro-metring system for blade lubrication

Cutt

ing

Standard Features – UCM 425

• Separate hydraulic system with control column

• Electric cutting pressure monitoring and piece counter

• Discharge conveyor with protective covering

• Length measuring device

UCM 425

Universal Circular Metal Up Cut Saw

PO 315 PK-PD


Manual / Semi-Automatic Circular Cut-Off Machines

OverviewRigid circular metal sawing machines offering manual, manual with pneumatic vice, or semi-automatic operation. Double self-centring vice prevents break off burrs. Saw head can swivel 45 degrees left and right. Slotting and longitudinal cutting are possible. Protective saw blade guard opens and closes automatically. Saw blade can be replaced quickly and easily.

PO 350 SA

PO 370

PO 275 SA

PO 275 PK-PD

PO 315

Model Range

Manual Pneumatic Clamp Semi-AutomaticPO 275 PO 275 PK/PD PO 275 SAPO 315 PO 315 PK/PD PO 315 SAPO 370 PO 350 SA

PO 275

PO 350 SA

Long service life and low maintenance are hallmarksof the technology behind the PO range of manualand semi-automatic circular cut-off machines. Therobust cutting head with double self centring viceensures a burr-free cut on various material sizes andsignificantly enhances the life of the saw blade.

SPECIFICATION UNIT PO 275 PO 315 PO 350 PO 370

Cutting Capacity Deg 90 45 90 45 90 45 90 45

Tube - Round mm 80 60 95 60 115 75 130 90

Tube - Square mm 75 x 75 50 x 50 85 x 85 70 x 70 110 x 110 80 x 80 130 x 130 85 x 85

Tube - Rectangular mm 90 x 75 60 x 50 110 x 75 75 x 50 150 x 90 100 x60 150 x 100 100 x 70

Solids - Round mm 38 25 55 38 60 40 60 40

Solids - Square mm 38 x 38 25 x 25 50 x 50 35 x 35 60 x 60 40 x 40 60 x 60 40 x 40

Max Clamp Opening mm 85 110 150 150

Blade Diameter mm 250 / 275 / 300 250 / 275 / 300 / 315 300 / 325 / 350 300 / 350 / 400

Blade Centre Hole Diameter mm 32 32 32 32

Drive Pins Diameter and PCD mm 10 x 63 10 x 63 10 x 63 10 x 63

Cutting Speed Rpm 45 / 90 42 / 80 26 / 50 26 / 50

Motor Kw 1.3 / 1.8 1.8 / 2.4 2.4 / 3 1.9 / 2.4

Machine Length mm 1000 700 900 900

Machine Width mm 800 1100 1300 700

Machine Height mm 1700 1400 2200 1500

Machine Weight Kg 220 / 250 / 300 280 / 320 / 450 530 / 500 380

Standard Features

• Double self-centring clamps

• Coolant pump and pedestal

• Two-speed cutting head

• Mitre sawing facility

• Enclosed safety guard


Cutt

ing

TIH 15


Aluminium Cutting Machines

SPECIFICATION UNIT TIH 20

Angle of Cut deg Adjustable 45L to 45R

Workable Height mm 860

Saw Blade Size mm 25.4 x 500

Cutting Speed rpm 3600

Motor Kw 3.75

Workable Area mm 900 x 900

Weight Kg 430

L x W x H mm 1200 x 1020 x 1700

SPECIFICATION UNIT TIH 15

Cutting Capacity 90 Deg 45 Deg

Tube – Round mm 130 130

Tube – Square mm 180 x 180 130 x 13

Tube – Rectangular mm 200 x 100 140 x 70

Solids – Round mm 60 60

Tube – Square mm 60 x 60 40 x 40

Max Clamp Opening mm 150

Blade Diameter mm 300 / 350 / 450

Blade Centre Hole Diameter mm 25,4 (32)

Drive Pins Diameter and PCD mm 10 x 63

Cutting Speed Rpm 3000

Motor Kw 3

Machine Length mm 840

Machine Width mm 660

Machine Height mm 1150

Machine Weight Kg 270

TIH 20

Semi Automatic aluminium up cut machine that performs clamping and cutting in one cycle.

Features

• When the foot switch is pressed, the machine will perform workpiece clamping and cutting automatically (Convenient).The built in sawblade rises up to cut the material and also allows cutting with single or several materials simultaneously, while the operators’ hands stay away from the sawblade (Safety)

• The clamping system and cutting system are controlled by their respective pneumatic cylinders. This design allows for independent adjustment of the cutting speed and clamping speed. The clamping system can ‘compact press’ the material

• Clamping System : Super wear-resisting stable linear slide rail clamping down on the material

• The clamp pressure for pressing is adjustable to prevent the distortion of the materials due to overloading

• The oil mist system lubricates and cools, increasing blade life

• The clamping height is adjustable

• Mitre cut up to 45 degrees from 0 and 90 degree cut

TIH 20


Cutt

ing

Cutt

ing


Aluminium Cutting Machines

SPECIFICATION UNIT TIH 24 C

Angle of Cut deg 90

Workable Height mm 850

Saw Blade Size mm 25.4 x 600

Cutting Speed rpm 3000

Motor Kw 5.6

Workable Area mm 1150 x 660

Weight Kg 550

L x W x H mm 1250 x 1250 x 1700

TIH 24 C

Band Sawing Machines

SPECIFICATIONS MANUAL MANUAL WITH DESCENT CONTROL

BE210S BE225S BE260S BE210SH BE225SH BE260SH

Cutting Capacity (mm)

90 Round 170 178 227 170 178 227

Square 170 x 170 178 x 178 220 x 220 170 x 170 178 x 178 220 x 220

Rectangular 210 x 170 225 x 110 260 x 110 210 x 170 225 x 110 260 x 110

45R Round 120 140 150 120 140 150

Square 110 x 110 130 x 130 145 x 145 110 x 110 130 x 130 145 x 145

Rectangular 200 x 125 200 x 125

60R Round 70 85 90 70 85 90

Square 60 x 60 80 x 80 85 x 85 60 x 60 80 x 80 85 x 85

Down Feed / Clamp By Hand By Hand By Hand By Hand By Hand By Hand

Blade Size 20 x 0.9 x 2110 20 x 0.9 x 2265 27 x 0.9 x 2460 20 x 0.9 x 2110 20 x 0.9 x 2265 27 x 0.9 x 2460

Cutting Speed m/min 40/80 30/60 36/72 40/80 30/60 36/72

Motor Kw 0.75 0.75 1.1 0.75 0.75 1.1

Weight Kg 170 180 250 170 180 250

L x W x H 1160x757x830 700x625x195 1550x740x925 1160x757x830 700x625x195 1550x740x925

BE 210S BE 225S BE 260S



Band Sawing Machines

BE 310 DSN

BE 350 DSA

Auto cuttingdevice

Vice stabilising

support

Dual directional

vice for angle cuts

Zero degree positioner with

cooler and chip gutter

BE 270 DSN

DSN Manual down feed

DS Auto cutting devise

DSA Hydraulic semi-automatic

Manual Semi-Automatic Hydraulic

BE270DS/DSN BE310DS/DSN BE350DS/DSN BE270DSA BE310DSA BE350DSA

Cutting Capacity (mm)

90 Round 227 250 270 227 250 270

Square 220 x 220 240 x 240 260 x 260 220 x 220 240 x 240 260 x 260


45R Round 150 200 240 150 200 240

Square 145 x 145 180 x 180 220 x 220 145 x 145 180 x 180 220 x 220


60R Round 90 120 160 90 120 160

Square 85 x 85 120 x 120 150 x 150 85 x 85 120 x 120 150 x 150

45L Round 110 150 210 110 150 210

Square 110 x 110 150 x 150 180 x 180 110 x 110 150 x 150 180 x 180


Down Feed Controlled Descent Controlled Descent Controlled Descent Hydraulic Hydraulic Hydraulic

Clamp Manual Manual Manual Hydraulic Hydraulic Hydraulic

Blade Size 27 x 0.9 x 2460 27 x 0.9 x 2725 27 x 0.9 x 3160 27 x 0.9 x 2460 27 x 0.9 x 2725 27 x 0.9 x 3160

Cutting Speed m/min 36/72 36/72 34/68 36/72 36/72 34/68

Motor Kw 1.1 1.1 1.5 1.1 1.1 1.5

Weight Kg 280 480 410 280 480 410

L x W x H 1550x740x1055 1700x750x1575 1840x750x1095 1550x740x1055 1700x750x1575 1840x750x1095


Cutt

ing


Manual and Pneumatically Operated Bar Shears

RTH 3L

RS1RS2

Standard Features

• Burr free cutting

• High production rates

• Swarfless cut offs

• Zero material loss in cut

• No swarf

RS1PN

RS2PN

SPECIFICATION RS1 RS2 RS1PN RS2PN

Shear Die Aperture Steps 1 - 8mm 5 - 16mm 2 - 12mm 1 - 8mm 5 - 16mm 2 - 12mm

Shear Die Aperture Increments 0.5mm 1mm 0.5 - 10mm 0.5mm 1mm 0.5 - 10mm

Length Stop 200mm 500mm 200mm 500mm

Max. Cutting Capacity (mm)

Low Carbon Steels 8mm 16mm 8mm 16mm

High Alloy Steels 6mm 12mm 6mm 12mm

Weight 8.5Kg 32Kg 30Kg 75Kg

L x W x H (mm) 480 x 300 x 240 800 x 300 x 240 700 x 500 x 500 900 x 600 x 800

SPECIFICATION UNIT RTH2L RTH3L

Diameter of Tubes mm 15 - 40 15 - 65

Wall Thickness % Max 7.5% of tube diameter Max 7.5% of tube diameter

Tube Quality Steamless or finn controlled (scraped) Steamless or finn controlled (scraped)

Tensile Strength n/mm 800 800

Max Tube Start Length mm 3000 3000

Power kW 1.5 4

Shearing Capacity Strokes/H 1500 1500

Machine Variants Long Long

Max. Cut Length 70 - 500 70 - 500


L x W x H mm 4250 x 750 x 1300 4250 x 1000 x 1450

RTH LongThe tube to be cut is fed by the operator through the sheering tool onto the mandrel bar and pushedback against the length stop. A micro switch in thelength stop is activated and the tube is cut. This process can be repeated continuously.

Tube Cutting System


Cutt

ing


Tube Cutting System

RTH2S

TMH 30

SPECIFICATION UNIT RTH2S RTH3S

Diameter of Tubes mm 15 - 40 15 - 65

Wall Thickness % Max 7.5% of tube diameter Max 7.5% of tube diameter

Tube Quality Steamless or finn controlled (scraped) Steamless or finn controlled (scraped)

Tensile Strength n/mm 800 800

Max Tube Start Length mm 3000 3000

Power kW 1.5 4

Shearing Capacity Strokes/H 1500 1500

Machine Variants Short Short

Max. Cut Length 30 - 150 30 - 150


L x W x H mm 2150 x 750 x 1300 4250 x 1000 x 1450

RTH ShortThe tube to be cut is inserted into the shearing hole and over the mandrel bar until contact is madewith the length stop. After the cutting operation, the mandrel together with the length stop is pulled out of the shear bushing. Once the cut off piece is outside the tool, it is stripped off from the mandrel by means of a top sleeve.

High volume production requirements can be met on our fully automatic hydraulicmodels. Production volumes of up to 6000 pieces per hour can be obtained. Max bar diameter is 30mm.

Fully Automatic Bar Shearing Machines

Various modules are available to meet production requirements

• Bunker feed unit

• Bar loading magazine

• Feeder unit

• First and last piece separation

• Tube cutting


Cutt

ing

TubeMartTM | NotchingTubeMartTM | Notching |4140|


Not

chin

g

TubeMartTM | NotchingTubeMartTM | Notching |4342|

TNM 70 Tube Notcher

Tube Notching machine ideal for round and square mild steel tubes up to 70mm. Abrasive belt of 75 x 2000mm runs at a speed of 2800rpm.Machine is supplied standard with a contact roller of 31.8mm.

TNM 70

Options

• Two speed motor to work stainless steeland mild steel tubes (TNS 70)

• Contact rolls with bearings from dia 20 to 70mm

Tube notching machine ideal for round and square mild steel tubes up to 145mm.Abrasive belt of 150 x 2000mm runs at a speed of 2800 rpm for mild steel and at 1400rpm for stainless steel. Machine is supplied standard with three contact rollers of19.05 mm, 31.8mm and 76.2mm.

TNS 145 Heavy Duty Tube Notcher

TNS 145


Not

chin

g

TubeMartTM | PolishingTubeMartTM | Polishing |4544|


Polis

hing

TubeMartTM | PolishingTubeMartTM | Polishing |4746|

Planetary Polishing Machines

TTP 70

TTP 100

Straight Tube Polishing Machines

TTL 100

SPECIFICATION UNIT TTL 100

Belt Length mm 4000

Belt Width mm Up to 100

Diameter Range mm 6 – 180

Motor 3.2 / 4kW – 1450 / 2900 rpm with motor start device

Feed Speed mm / min 0 – 25 infinitely variable


Polis

hing

TubeMartTM | End FinishingTubeMartTM | End Finishing |4948|


End

Fini

shin

g

End

Fini

shin

g


Tube End Forming

The TM 70 end forming machine is a basic machine for expanding and reducing tube by the use of segmented tooling.

Tubing up to 76.2mm diameter is expanded using segmented fingers and amandrel inside the tube, or reduced using segmented jaws forced through afixed cone on the outside of the tube.

The segmented tooling is standard drop in type used by leading tube end formers globally.

TM 70

TME 40-3

TME 40-2

Tube end form tooling

SPECIFICATION UNIT TM 70

Max Round Tube Mild Steel mm 76.2 x 2

Max Forming Length mm 60

Cycle Time Per Form Sec 4

Working Height mm 950

Hydraulic Motor Kw 7.5

Total Power Kw 7.5

Hydraulic Pressure Bar 150

Hydraulic Tank Capacity L 190

Machine Length mm 1420

Machine Width mm 650

Machine Height mm 2000

Machine Weight Kg 1200

SPECIFICATION UNIT TME 40 TME 40-2 TME 40-3 TME 60 TME 60-2

Max Round Tube Mild Steel mm 40 x 1.5 40 x 1.5 40 x 4.5 60 x 1.5 60 x 1.5

Max Forming Length mm 110 100 100 120 110

Number of Forming Heads 1 2 3 1 2

Cycle Time Per Form Secs 6 6 6 7 7


Hydraulic Motor Kw 4 5.5 5.5 5.5 5.5

Total Power Kw 4 5.5 5.5 5.5 5.5

Hydraulic Pressure Bar 120 120 120 120 120

Hydraulic Tank Capacity L 240 240 240 320 320

Machine Length mm 1180 1180 1180 1380 1380

Machine Width mm 1180 1180 1180 1250 1250

Machine Height mm 1400 1400 1400 1450 1450

Machine Weight Kg 400 850 1000 520 1000

Standard Features

• Allen-Bradley PLC control

• Foot pedal cycle start

• Air heat exchange

• 100mm ram stroke

Optional

• Tooling

TM 70



Tube End Finishing MachinesTube Tapering Machines

SPECIFICATION UNIT TA 50 M TA 50 H

Max Round Tube Mild Steel mm 50 x 2 50 x 2

Max Forming Length mm 290 290

Cycle Time Per Form Sec 7 ~ 30 7 ~ 30


Motor Kw 4 8

Total Power Kw 4 8

Hydraulic Tank Capacity L 150




Machine Weight Kg 2300 3000

SPECIFICATION UNIT TEF 50 TEF 110

Max Round Tube Mild Steel mm 50 x 2 110 x 2Cycle Time Per Form Sec 4 5Working Height mm 1050 1050Motor Kw 2 2Total Power Kw 2 2Air Pressure Required Bar 4 ~ 6 4 ~ 6Machine Length mm 1200 1400Machine Width mm 900 900Machine Height mm 1200 1200Machine Weight Kg 400 560

TA 50 H

TA 50 M

TEF 50TEF 110

De-BurrerDeburring machines for pipes and profiles.

TBE 60


End

Fini

shin

g

TubeMartTM | ConsumablesTubeMartTM | Consumables |5554|


Cons

umab

les

Cons

umab

les

Lubricants

PRODUCT DESCRIPTION ADDISONMCKEE CUTTING QUALITIES FORMING METALS PACK SIZENAME PRODUCT CODE QUALITIES

AMgel Light/Med Duty Tube Bending Gel XE11020 3 3 3 3 3 X X X 3 3 3 3 3AMgel Plus Med/Heavy Duty Tube Bending Gel XE12020 4 4 X 3 X 3 3 3 3 3 3 3AMgel Ultimate Med to Heavy Duty Forming XE13020 5 5 3 3 3 3 3

Turn

ing

Hea

vyTu

rnin

gM

illin

gH

eavy

Mill

ing

Dril

ling

Dee

pH

ole

Dril

l&Bo

reTa

ppin

g&

Thre

adin

gTh

read

Rolli

ngSi

ngle

Poin

tRe

amin

gBr

oach

ing

Gea

rCu

ttin

g&

Hob

bing

Saw

ing

&Ba

ndSa

win

gSh

earin

gFo

rmin

gD

eep

Dra

win

gRo

llFo

rmin

gFi

neBl

anki

ngBe

ndin

gM

andr

elTu

beBe

ndin

gSt

eel

Zinc

Coat

edSt

eels

Stai

nles

sSt

eel

Alum

iniu

mAl

umin

ised

Stee

lCo

pper

/Br

ass

5U

SG

allo

ns19

lt/

20lt

25lt

55U

SG

allo

ns20

5lt


AMform 1 Med to Heavy Duty Forming XE21025 5 4 4 2 4 4 3 X 3 3 3 3 3 3AMmist 1 Micro Applied GP Coolant XE25025 3 3 2 3 1 3 2 3 3 3 3 3 3 3 3AMmist 2 Micro Applied GP Coolant XE26025 3 3 2 3 1 3 2 3 3 3 3 3 3 3 3AMform 2 Heavy Duty Oil Based Lub XE22025 5 4 3 2 4 4 3 3 3 3 3 3AMform 3 Oil Based Lub XE23025 5 3 4 2 3 3 3 3 3 3 3 3

Turn

ing

Hea

vyTu

rnin

gM

illin

gH

eavy

Mill

ing

Dril

ling

Dee

pH

ole

Dril

l&Bo

reTa

ppin

g&

Thre

adin

gTh

read

Rolli

ngSi

ngle

Poin

tRe

amin

gBr

oach

ing

Gea

rCu

ttin

g&

Hob

bing

Saw

ing

&Ba

ndSa

win

gSh

earin

gFo

rmin

gD

eep

Dra

win

gRo

llFo

rmin

gFi

neBl

anki

ngBe

ndin

gM

andr

elTu

beBe

ndin

gSt

eel

Zinc

Coat

edSt

eels

Stai

nles

sSt

eel

Alum

iniu

mAl

umin

ised

Stee

lCo

pper

/Br

ass

5U

SG

allo

ns19

lt/

20lt

25lt

55U

SG

allo

ns20

5lt


AMcut 1 Gen Purpose - Low Oil Content Emulsion XE31025 3 X 3 X 3 X X X X X X X 3 3 1 3 1 3 3AMcut 2 Extreme Pressure Emulsion XE32025 3 3 3 3 3 X X 3 3 3 X 3 3 4 2 3 1 3 3 3 3 3 3 3 X 3 3AMcut 3 Fully Synthetic Multi Purpose Coolant XE33025 3 X 3 X 3 X X X X X X X 3 3 1 3 1 3 3 3 3 3 3 3 3 3 3

Turn

ing

Hea

vyTu

rnin

gM

illin

gH

eavy

Mill

ing

Dril

ling

Dee

pH

ole

Dril

l&Bo

reTa

ppin

g&

Thre

adin

gTh

read

Rolli

ngSi

ngle

Poin

tRe

amin

gBr

oach

ing

Gea

rCu

ttin

g&

Hob

bing

Saw

ing

&Ba

ndSa

win

gSh

earin

gFo

rmin

gD

eep

Dra

win

gRo

llFo

rmin

gFi

neBl

anki

ngBe

ndin

gM

andr

elTu

beBe

ndin

gSt

eel

Zinc

Coat

edSt

eels

Stai

nles

sSt

eel

Alum

iniu

mAl

umin

ised

Stee

lCo

pper

/Br

ass

5U

SG

allo

ns19

lt/

20lt

25lt

55U

SG

allo

ns20

5lt


AMwash 1 Neutral Inhibited Degreaser XE41025 3 3 3 3 3 3 3 3AMwash 2 Med to Heavy Duty Degreaser XE42025 3 X 3 X 3 X 3 3

Turn

ing

Hea

vyTu

rnin

gM

illin

gH

eavy

Mill

ing

Dril

ling

Dee

pH

ole

Dril

l&Bo

reTa

ppin

g&

Thre

adin

gTh

read

Rolli

ngSi

ngle

Poin

tRe

amin

gBr

oach

ing

Gea

rCu

ttin

g&

Hob

bing

Saw

ing

&Ba

ndSa

win

gSh

earin

gFo

rmin

gD

eep

Dra

win

gRo

llFo

rmin

gFi

neBl

anki

ngBe

ndin

gM

andr

elTu

beBe

ndin

gSt

eel

Zinc

Coat

edSt

eels

Stai

nles

sSt

eel

Alum

iniu

mAl

umin

ised

Stee

lCo

pper

/Br

ass

5U

SG

allo

ns19

lt/

20lt

25lt

55U

SG

allo

ns20

5lt

Excellent 5

Very High 4

Good 3

Medium 2

Low 1

Can be used 3

Not Recommended X

NB – Information should only be used as a guideline. It is always recommended that trials be undertaken to establish the optimum product for conditions prevailing andcustomer’s specific performance requirements.

Forming Gels Cutting Fluids

End Forming Lubricants Tube Washing

Key



Cons

umab

les



Saw Blades

Saw blades are supplied against customers specific requirements.

TubeMartTM dealers will assist with orders.

The following information will guide you as to what tooling is required to produce a quality mandrel bent component. As material vary, the tooling requirements may also vary.

Mandrel and Wiper Die Selection Guide for TubeMartTM Benders

Tube OD to Wall Thickness Ratio = Tube Outside Diameter = Factor 1Tube Wall Thickness

Centreline Radius to Tube OD Ratio = Centreline Radius = Factor 2Tube Outside Diameter

FACTOR 2

FACTOR 1 1.5 2 2.5 3 4 5

10 M1 M1 P P

15 M1 M1 P P

20 M1W M1 M1 M1 P

25 M1W M1W M1 M1 M1

30 M2W M2W M1W M1 M1 M1

35 M3W M2W M2W M2W M2 M1

40 M3W M3W M3W M3W M2W M2

45 M3W M3W M3W M3W M2W M2W



Mandrel + 1 Ball M1Wiper Die WPlug Mandrel P

Key

TubeMartTM | NotesTubeMartTM | Notes |6160|

In order for TubeMartTM to offer the best prices on bend tooling, the following information is required per set of tools:

Ordering Tooling

Machine MakeMachine ModelMaterial to be BentGrade of MaterialMaterial ProfileDimensionsMaterial Wall ThicknessMax Bend AngleVolumes Per Month. Single Shaft ProductionCentre Line Radius

Mild Steel: Stainless Steel: Other:

Round: Square: Other:Min: Max:Min: Max:

Sketch of Component

TOOLING REQUIREDBend DieClamp DieFollower SlideColletMandrelWiper Die

One Piece:: Segments:Shank: Balls: Links:Solid: Insert: Insert Holder:


Notes:

Cons

umab

les

Documents

- Tube Solutions subsidiary of To find out how you can participate in the ... Max Round Tube Mild Steel mm 18 x 2 38.1 x 2 50.8 x 3 63 x 3 80 x 3 89 x 6 114 x 8