Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
16 1716 17
SOFFIT FIXED FACE FIXED
High quality hardware makes medium weight folding doors efficient and easy-to-use. Two and four leaf kits are available.
HARDWARE PACK (no. "HF2/100PACK") = KIT w/o track:1 ea 283 nylon bodied, needle bearing, acetal wheel hanger1 ea 289T heavy duty top pivot1 ea 289B heavy duty bottom pivot3 ea 282HD heavy duty butt hinges1 ea 106HF/94 roller guide (use w/94A)(For 4 leaf configurations, order 2 each of the above hardware pack HF2/100PACK)
HUSKYFOLDING100
OPTIONAL EXTRAS include:2815 281 brackets - 5 each400 aluminum flush pull (4-1/4" x 1-7/8")333 aluminum flush bolt (6" x 1-3/8")
HF2/100 KITS (complete, ready to install) include:1 ea 280/4 or pre-drilled track, in steel or 280A/4 aluminum, 4 feet1 ea 94A/4 aluminum floor channel, 4 feet1 ea 283 nylon bodied, needle bearing, acetal wheel hanger1 ea 289T heavy duty top pivot1 ea 289B heavy duty bottom pivot3 ea 282HD heavy duty butt hinges1 ea 106HF/94 roller guide (use w / 94A)(Kit components can be ordered individually)
FOR FOLDING DOORS AND ROOM DIVIDERS TO 100 lbs.
HF4/100 KITS (complete, ready to install) include:1 ea 280/8 or pre-drilled track, in steel or 280A/8 aluminum, 8 feet1 ea 94A/8 aluminum floor channel, 8 feet2 ea 283 nylon bodied, needle bearing acetal wheel hangers2 ea 289T heavy duty top pivots2 ea 289B heavy duty bottom pivots6 ea 282HD heavy duty butt hinges2 ea 106HF/94 roller guides (use w/94A)(Kit components can be ordered individually)
Kit No. Track Max Door Max No. of Door Leaf Mat'l / Length Leaf Size Opening Leaves Thickness
HF2/100/4 steel/4 ft. 96" H x 24" W 48" 2 13/16" - 1-3/4"
HF2/100A/4 aluminum/4 ft. 96" H x 24" W 48" 2 13/16" - 1-3/4"
HF4/100/8 steel/8 ft. 96" H x 24" W 96" 4 13/16" - 1-3/4"
HF4/100A/8 aluminum/8 ft. 96" H x 24" W 96" 4 13/16" - 1-3/4"
Order KITS based on material, length of track and number of leaves:
100 lbs.max door weight
Top Pivot289T
BottomPivot289B
Track 280Hanger 283
Hinge282HD
Guide106HF/94
Channel94A
281(optional)
94A
1-1/8" 2-13/16" MAX2-1/2" MIN
289T
289B13/16"
2" MAX1-3/4" MIN
280
283
282HD
15/16" MAX5/8" MIN
106HF/94
13/16"
100 lbs.
100 lbs.
1/4"
18 1918 19
PACER INTERIOR CENTERFOLD FOR WOOD DOORS
Use in Place of401/402/403 Hinges:
PemkoHinge™Continuous Geared
Aluminum Hinges
Track600A
Hanger61B - 61B/4
Lock NutAdjustable Nut
Butts403
102 x 57
Channel 94A
Guide106N/94
(4"-21/4")
(28.6)13 8
(17.5)11 16
(52.4)21 16
3 16(4.7)
13 16(20.6)
13 16(20.6)
3 16(4.7)
(55.5)23 16
11 16(17.5)
3 8(9.5)
1 2(12.7)
(25.4)1
18 1918 19
PACER INTERIOR CENTERFOLD FOR WOOD DOORS
All full leaves are of equal width.A pivoting half-leaf (dimension C) is half the width of a full leaf
(dimension A), less half of the leaf thickness (dimension B).
CAPACITY
Max. door weight: 77 lbs. (35kg) (61B hanger)
165 lbs. (75kg) (61B/4 hanger)
Max. door height: 8'10" (2700mm)
Max. door width: 2'11" (900mm)
Door thickness: 13/8"-115/16" (35mm-50mm)
APPLICATIONS
Top-hung Pacer gear and fittings for center folding wood partition doors. Leaves are hung centrally and can fold to one or both sides. For applications hinged to the jamb, 31/2, 51/2 or 71/2 leaves can be used with the half-leaf hinged to the jamb. For best operation of floating units, 5, 7 or 9 leaves should be used. Any access door should be hinged separately to the jamb.
DOOR TYPES
Residential and commercial wood doors.
TECHNICAL INFORMATION
Track: Aluminum 600A Available in 6', 8', 10', and 16'5", lengths
Brackets: Face fix 1B Jointing bracket 1BX
Hangers: Two-wheeled hanger 61B Four-wheeled hanger 61B/4
Guides: Nylon guide roller 106N/94
Guide Channel: Brass 94 Aluminum 94A 94 channel available in 4'11" (1.5 meter) and 9'10" (3 meter) lengths. 94A channel available in 6', 8', and 12' lengths.
Hinges: Butt hinges 403
Accessories: Flush pull 400 Flush bolts 333/454 Narrow flush bolt and keep F3715 & F3734
Track600
Plan 1 Plan 2 Plan 3
Rebated Joints
Note:No offset to butts on post
31/2 leaveshinged to post.
As Plan 1
5 leavesfloating folding.
As Plan 2
51/2 leaveshinged to post.
As Plan 3
C
B
A
Hanger61B
Hanger61B/4
20 2120 21
PACER INTERIOR ENDFOLD FOR WOOD DOORS
Use in Place of401/402/403 Hinges:
PemkoHinge™Continuous Geared
Aluminum Hinges
26
Track600
Track600A
Top Pivot21B/P
Top View of Pivot21B/P
21K/PXTop Pivot
Note: track face fixed use bracket 1B - 1BX. See page 89.
Butts403
21B-21B/4Hanger
Lock NutAdjustableNut
Lock Nut
Locking Bolt
21B - (2 Wheels)
AdjustableNut
26
12
DoorThickness
Guide21N/94
Cover
(40x45x3)
Clearance3mm
Radiusrequired:which sideof doordependson swingdirection
Channel94A
(70)
12
13 13
1/2"
1"
1/2"
1/2" 1/2"
1"
(4.7)3/16"
(3.1)1/8 "
(13/16")
423/ "
(3/16")
19/16"x13/4"x1/8"
(1/8")
(52.4)21 16
(55.5)23 16
(152.4)6
(38.1)11 2
(38.1)11 2
(38.1)11 2
(28.7)11 8
(4.8)
3 16
(4.8)
3 16
(20.6)
13 16
(20.6)
13 16
(4.8)
3 16
(4.8)
3 16
(17.5)
11 16
(9.5)
3 8
(17.5)
11 16
(9.5)
3 8
(33.3)(22.2)17 8 5 16
BottomPivot
(155.5)6 1 8
(155.5)6 1 8
(25.4)1
(25.4)1(152.4)
6
(101.6)4
(25.4)1
(25.4) 1
13/8"-13/4"(35-44)
20 2120 21
B
X A
Note: Butt hinges on posts are not offset
All leaves are of equal width except the leaf hinged to the post. The dimension for the leaf hinged to the post (X) is, A, less B (half the leaf thickness), less 11/2" (38mm).
Formula: X=(A-B)-11/2" (38mm)
Hinged to Post Option
Note: Hangers and guides are to be fitted to alternate leaves only.
CAPACITY
Max. door weight: 77 lbs. (35kg) (21B hanger)
165 lbs. (75kg) (21B/4 hanger)
165 lbs. (75kg) (21BO/4 hanger)
Max. door height: 8'10" (2700mm)
Max. door width: 2'11" (900mm)
Door thickness: 13/8"-13/4" (35mm-44mm)
APPLICATIONS
Pacer Endfold offers both two-wheeled and four-wheeled hangers to cover a wide range of residential and commercial applications. Leaves can be hung to the left or the right of an opening, or hung as floating units. In applications using the four-wheeled hanger with an even number of leaves folding left and right meeting in the center of the opening, an offset hanger is required (Plan 4).
DOOR TYPES
Residential and commercial wood doors.
TECHNICAL INFORMATION
Track: Aluminum 600A Available in 6', 8', 10', and 16'5", lengths
Brackets: Face fix 1B Jointing bracket 1BX Hangers: Two-wheeled hanger 21B Four-wheeled hanger 21B/4 Four-wheeled offset hanger 21BO/4
Pivots: For door widths between 1"-13/8" (25-34mm) 21K/PX For door widths between 13/8"-13/4" (35-44mm) 21B/P Guides: Nylon end guide roller 21N/94
Guide Channel: Brass 94 Aluminum 94A
Hinges: Butt hinges 403
Accessories: Flush pull 400 Flush bolts 333/454 Narrow flush bolt and keep F3715 & F3734
* Note: Using a pivot allows leaves to be of equal width.
Side toOpen
Side toOpen
Side toOpen
Side toOpen
Plan 3
4 leaves startingwith pivot
Plan 2 Plan 1
Plan 4
5 leaves starting with pivotNo.5 is swing leaf
6 leaves floatingto left
21K/PX21B/4
(4 Wheels)
4 leaves to eitherside startingwith pivot
21BO/4Offset
21B/4
21K/PXPivot
21B/P
21B(2 Wheels)
(38.1)11 2
(38.1)11 2
(38.1)11 2
(38.1)11 2
(100)315 16
min.
22 2322 23
PACER ENDFOLD FOR GLASS DOORS
(5/16"-3/8")
1/4"13/16"
(6’6")
* For Glass Dimensions and Cutting Please Contact P C Henderson Technical Sales.* In Combination with 971 Glass Height is the Opening Height less 67.5mm (25/8")
TopPivotEF07
HingeEF05
LockNut
Hinge withFlush Bolt
EF04BottomPivotEF08
Mid GuideEF06 End Guide
EF02
LockNut
LockNut
LockNut
LockNut
MidHangerEF03 End Hanger
EF01/2 (2 Wheels)or EF01/4 (4 Wheels)Lock
Nut
(6.4)
(20.6)
Inside Outside Inside Inside Inside
8-10mm
(31/2")
*Glass Heightis the
OpeningHeight less
88.5mm(31/2")
*Glass Heightis the
OpeningHeight less
88.5mm(31/2")
*Glass Heightis the
OpeningHeight less
88.5mm(31/2")
*Glass Heightis the
OpeningHeight less
88.5mm
Optional Hingefor DoorsExceeding2000mm
Track 600A
971Threshold
971Threshold
971Threshold
971Threshold
(52.4)21 16
(44.5)13 4
(52.4)21 16
(52.4)21 16
(52.4)21 16
(55.5)23 16
(55.5)23 16
(55.5)23 16
(55.5)23 16
(4.7)3/16"
(25.4)1
(25.4)1
(25.4)1
(25.4)1
Section D-DSection B-B Section C-CSection A-A
Outside Outside Outside
(44.5)13 4
(44.5)13 4
(44.5)13 4
22 2322 23
* For other options see Guide to Quantities
TECHNICAL INFORMATION
Track: Aluminum 600A Available in 6', 8', 10', and 16'5", lengths
Brackets: Face fix 1B Jointing bracket 1BX Hangers: Two-wheeled end hanger with single hinge* EF01/2 Four-wheeled intermediate hanger with double hinge* EF03 Four-wheeled end hanger with single hinge* EF01/4
Hinges: Double hinge EF05
Pivots: Top pivot with single hinge* EF07 Bottom pivot with single hinge* EF08 Guides: End guide with single hinge* EF02 Intermediate guide with double hinge* EF06
Guide Channel: Brass 94 Aluminum 94A
Accessories: Double hinge with spring-loaded foot operated bolt EF04 Sliding door lock for glass panels 618 Sliding door receiving lock 619 Spring-loaded foot operated bolt EF09
* All with stainless steel strapbolt/spindle.
CAPACITY
Max. panel weight: 99 lbs. (45kg)
Max. panel height: 7'10" (2400mm)
Max. panel width: 2'6" (750mm)
Panel thickness: 5/16" (8mm) or 3/8" (10mm)
APPLICATIONS
Pacer Endfold for glass is a system designed for both interior and exterior applications. Panels and hinges are connected using a system of glass hinges.
DOOR TYPES
Glass panels of 5/16" (8mm) or 3/8" (10mm) thickness in tempered glass.
GLASS WEIGHT
3/8" glass 5.05 lbs./sq. ft.1/2" glass 6.4 lbs./sq. ft.
C
CBA B
DBBA
D
415/16"
(5/16")
Outside
Inside
For Glass Dimensions and CuttingPlease Contact P C Henderson Technical Sales.
Track 600A
EF05 EF03 EF01/2orEF01/4
EF07
EF08 EF04 EF06
Channel 94A
EF02
(125.4)
Lock618
R=8
Plan: 4 doors folding to the left.
OptionalHinges,Refer toGuide toQuantities
(4.7)
3 16(3.1)
1 8(3.1)
1 8(3.1)
1 8(4.7)
3 16
(55.6)23 16
24 2524 25
PACER EXTERIOR ENDFOLD FOR WOOD DOORS
Nut
LockNut
OutsideInside OutsideInside
Nut
LockNut
Guide67B
(43-57)
Hinge Sleeve
Channel 94A
Clearance
971
111/16"-21/4"
(20.6)13 16
(20.6)13 16 (20.6)13 16
(20.6)
13 16
(4.8)3 16
(85.7)3 3 8
Track600A
CramPlate
Hanger62B
(60.3)2 3 8
(55.5)2 3 16
(85.7)3 3 8
(85.7)3 3 8
(52.4)2 1 16
(34.9)13 8
Hinge65B
(3/4” or 1-9/16”)(20mm 0r 40mm)
For Fixing InstructionsSee Flexirol
page 28
Threshold
(4.8)3 16(20.6)13 16
(20)
13 16
24 2524 25
Hinges for hangers and guides must be ordered separately.Use a single hinge for end hangers and guides, double hinge for intermediate hangers and guides.
TECHNICAL INFORMATION
Track: Aluminum 600A Available in 6', 8', 10', and 16'5", lengths
Brackets: Face fix 1B Joining track 1BX Hangers: Intermediate hanger for wood doors with 513/16" (148mm) strapbolt, no hinge 62BA/148 End hanger for wood doors with 41/16" (104mm) strapbolt, no hinge 63BA/104 Offset end hanger for all doors with 41/2" (114mm) strapbolt, no hinge 63BOA/114
Guides: Intermediate guide for wood doors with 515/16" (150mm) spindle, no hinge 67BA/150 End guide for wood doors with 43/16" (110mm) spindle, no hinge 68BA/110
Guide Channel: Brass 94 Aluminum 94A
Hinges:✝ 13/16" (20mm) single hinge for wood/aluminum doors 65B/20/1 13/16" (20mm) double hinge for wood/aluminum doors 65B/20 19/16" (40mm) single hinge for wood/aluminum doors 65B/40/1 19/16" (40mm) double hinge for wood/aluminum doors 65B/40 13/16"-19/16" (20-40mm) double hinge for wood/aluminum frames 65B/20-40
Accessories: Flush pull 400 Flush bolts 333/454 Narrow flush bolt and keep F3715 & F3734
✝ Refer to page 110 for hinge installation.
CAPACITY
Max. door weight: 143 lbs. (65kg)
Max. door height: 9'10" (3000mm)
Max. door width: 2'11" (900mm)
Door thickness: 111/16"-21/4" (43mm-57mm)
APPLICATIONS
Top-hung Pacer gear for end folding exterior doors in wood. Pacer Endfold offers four-wheeled hangers with offset option to cover a wide range of residential and commercial applications. In applications using the four-wheeled hanger with an even number of leaves folding left and right meeting in the center of the opening, an offset hanger is required.
DOOR TYPES
Residential and commercial wood doors.
Outside
InsideA B
XX
OpeningWidth
Opening Width Track600
65BHinge
68BAGuidewithSingleHinge
63BOAOffsetHanger
with SingleHinge
F3715
Channel 94A*2 doors folding to the left.
Note: Width of Door Bis Door A + 15mm
(41.2)15 8
Center toCenter XDistanceof Hingesis AlwaysEven
(4.7)
3 16(4.7)
3 16(3.2)
1 8
SwingDoor
Track600
65BHinge 62BA
Hangerwith
65B DoubleHinge
F3715
67BA Guidewith
65B DoubleHinge
Channel 94A*3 doors folding to the left
EvenX
EvenX
Opening Width
Opening Width
Outside
InsideAll
Doorsof SameWidth
(41.3)15 8
(41.3)15 8
(4.7)
3 16(3.2)
1 8(3.2)
1 8(4.7)
3 16
26 2726 27
PACER EXTERIOR ENDFOLD FOR ALUMINUM DOORS
971 Threshold
Track 600A
Swing Door
67BAGuidewith65B
DoubleHinge
7mm (1/4") Packer - S7
Stainless SteelRoller Guide
Spindle
(20mm or 40mm)
(1/2")
13/16"or 19/16"
Track 600A
Doors notby PCH
Doors notby PCH
NutLock Nut
PlasticCover
Nut
Lock Nut
PlasticCover
(52.4)2 1 16
(55.5)2 3 16
(54.0)2 1 8
(54.0)2 1 8
Channel 94A
HangerOutside
Track 600A
Inside
(20.6)
13 16
(4.7)
3 16
(130.2)5 1 8
(104.8)4 1 8
Hanger62BA/250with 65BDouble Hinge
(25.4)1
(20mm or 40mm)13/16"or 19/16"
67BA/220with 65B Hinge
Even Even
Plan: 3 doors folding to the right
26 2726 27
Squared Joint
Hinges for hangers and guides must be ordered separately.Use a single hinge for end hangers and guides, double hinge for intermediate hangers and guides.
Mitred Joint
CAPACITY
Max. door weight: 143 lbs. (65kg)
Max. door height: 9'10" (3000mm)
Max. door width: 2'11" (900mm)
Door thickness: 13/8"-115/16" (35mm-50mm)
APPLICATIONS
Top-hung Pacer gear for end folding exterior doors in aluminum. Pacer Endfold offers four-wheeled hangers with an offset option to cover a wide range of residential and commercial applications. In applications with an even number of leaves folding left and right meeting in the center of the opening, an offset hanger is required.
DOOR TYPES
Pacer Exterior Endfold is suitable for both residential and commer-cial aluminum doors. Fixing components are not supplied as standard for aluminum doors.
TECHNICAL INFORMATION
Track: Aluminum 600A Available in 6', 8', 10', and 16'5", lengths
Brackets: Face fix 1B Joining track 1BX
*Hangers: Intermediate hanger for aluminum doors with no hinge 513/16" (148mm)/915/16" (250mm) strapbolt 62BA/148 62BA/250 End hanger for aluminum doors with no hinge 51/2" (140mm)/81/16" (205mm) strapbolt 63BA/104 63BA/205 Offset end hanger for all doors with no hinge 41/2" (114mm) strapbolt 63BOA/114 63BOA/114
*Guides: Intermediate guide for aluminum doors with no hinge 515/16" (150mm)/811/16" (220mm) spindle 67BA/150 67BA/220 End guide for aluminum doors with no hinge 45/16" (110mm)/71/16" (180mm) spindle 68BA/110 68BA/180
Guide Channel: Brass 94 Aluminum 94A
Hinges: 13/16" (20mm) single hinge for wood/aluminum doors 65B/20/1 13/16" (20mm) double hinge for wood/aluminum doors 65B/20 19/16" (40mm) single hinge for wood/aluminum doors 65B/40/1 19/16" (40mm) double hinge for wood/aluminum doors 65B/40 13/16"-19/16" (20-40mm) double hinge for wood/aluminum frames 65B/20-40
Accessories: Flush pull 400 Flush bolts 333/454 Narrow flush bolt and keep F3715 & F3734
* All with stainless steel strapbolt/spindle.
S7 Packer
67BA/220
Channel 94A
Alternative Guiding System
65BDoubleHinge
(13/16” or 1-9/16”)(20mm or 40mm)
(6.4)
1 4
(19.1)
3 4
(20.6)
13 16
(20.6)
13 16(4.7)3/16"
(104.8)4 1 8
28 2928 29
FLEXIROL INTERIOR CENTERFOLD FOR WOOD DOORS
Use in Place of401/402/403 Hinges:
PemkoHinge™Continuous Geared
Aluminum Hinges
38
(6)
(19)(11/2")
3/4"
1/4"
4"x21/4"
Suspended Ceiling Bracketwith Vertical Adjustment
Track550A
Butts 403102 x 57
Adjustable Nut
Guide 106N/94
Channel 94A(20.6)
13 16
(4.7)
3 16
(20.6) 13 16
(98.4)3 7 8
(73.0)2 7 8
(39.7)(7.9)15 16 9 16
28 2928 29
All full leaves are of equal width.A pivoting half-leaf (dimension C) is half the width of a full leaf
(dimension A), less half of the leaf thickness (dimension B).
Note: Hangers and guides are to be fitted to alternate leaves only.
TECHNICAL INFORMATION
Track: 550A
Brackets: Face fix 1A/550 Soffit fix 3S/550 Hangers: Wood doors 556/61
Guides: Nylon roller guide 106N/94
Guide Channel: Brass 94 Aluminum 94A
Hinges: Butt hinges 403
Accessories: Flush pull 400 Flush bolts 333/454 Narrow flush bolt and keep F3715 & F3734
CAPACITY
Max. door weight: 275 lbs. (125kg)
Max. door height: 14'9" (4500mm)
Max. door width: 4' (1200mm)
Door thickness: 111/16"-21/4" (43mm-57mm)
APPLICATIONS
Top-hung Flexirol gear and fittings for center folding wood partition doors. Leaves are hung centrally and can fold to one or both sides. For applications hinged to the jamb, 31/2, 51/2 or 71/2 leaves can be used with the half-leaf hinged to the jamb. For best operation of floating units, 5, 7 or 9 leaves should be used. Any access door should be hinged separately to the jamb.
DOOR TYPES
Heavy commercial wood doors.
Note:No offset tobutts on post
A
31/2 leaveshinged to post.
As Plan 1
5 leaves floatingfolding.
As Plan 2
51/2 leaveshinged to post.
As Plan 3
C
B
A
Plan 1
Track550
Plan 2 Plan 3
30 3130 31
FLEXIROL INTERIOR ENDFOLD FOR WOOD DOORS
Use in Place of401/402/403 Hinges:
PemkoHinge™Continuous Geared
Aluminum Hinges
(6)
(19)
Adjustable Nut
Locking Bolt
(6)
(38)
(3)
(28)
Clearance
(19)3/4"
1/4"
11/2"3/4"
1/4"
(3mm)1/8"
11/8"13/16"
81/ "3/16"(5)
(98.4)3 7 8
(44.5)13 4
(44.5)13 4
(38.1)11 2
(73.0)2 7 8
Hanger556/21
Top Pivot21/550P
Top Viewof Pivot21/550P
Channel 94A
Guide21R/94
Channel94A
(25.4)1
(20.6)13 16
(20.6)13 16
(39.7)(7.9)15 16 9 16
Butts403
DoorThickness
(57.2)(42.9)2111 16 1 4
(1/4")Radius required: which side depends on swing direction
30 3130 31
B
X A
Note: Butt hinges on posts are not offset
All leaves are of equal width except the leaf hinged to the post. The dimension for the leaf hinged to the post (X) is, A, less B (half the leaf thickness), less 45mm (13/4").
Formula: X=(A-B)-45mm (13/4")
Hinged to Post Option
CAPACITY
Max. door weight: 275 lbs. (125kg)
Max. door height: 14'9" (4500mm)
Max. door width: 4' (1200mm)
Door thickness: 111/16"-21/4" (43mm-57mm)
APPLICATIONS
Top-hung Flexirol gear and fittings for end folding wood partition doors. Leaves can be hung to the left or right of an opening or hung as floating units.
DOOR TYPES
Heavy commercial wood doors.
TECHNICAL INFORMATION
Track: 550 (see component section for range of finishes)
Brackets: Face fix 1A/550 Soffit fix 3S/550 Hangers: Wood doors 556/21
Pivots: Wood doors 21/550P
Guides: Brass end guide roller 21R/94
Guide Channel: Brass 94 Aluminum 94A
Hinges: Butt hinges 403
Accessories: Flush pull 400 Flush bolts 333/454 Narrow flush bolt and keep F3715 & F3734
21/550P
556/21
Side to Open
4 leaves startingwith pivot
5 leaves starting with pivot# 5 is swing leaf
6 leaves floatingto left
4 leaves to either sidestarting with pivots
Side to Open
Side toOpen
Side toOpen
Plan 4
Plan 1 Plan 2 Plan 3
(44.5)13 4
(44.5)13 4
(100 min.)315 16
32 3332 33
FLEXIROL EXTERIOR ENDFOLD FOR WOOD DOORS
Lock Nut
Nut
971 Thresh.
Clearance
Hanger 556A/221with 65B Hinge
Track 550A
(20mm or 40mm)
NutLockNut
Inside Outside
CramPlate
Hinge65B
Guide67BA
Inside Outside
(43-57)
HingeSleeve
Channel 94A
13/16" or 19/16"
111/16"-21/4"
1/4"
(98.4)3 7 8
(73)31 8
(85.7)33 8
(85.7)33 8
(85.7)33 8
(34.9)13 8
(60.3)23 8
(39.7)19 16
(36.5)17 16
(4.7)
3 16
(20.6)
13 16
(20.6)
13 16
(20.6)
13 16
(20.6)
13 16 (20.6)13 16
(20.6)
(20.6)
(5)
13 16
13 16
3 16
32 3332 33
* For other options see Hinge Installation page 110.
Hinges for hangers and guides must be ordered separately.Use a single hinge for end hangers and guides, double hinge for intermediate hangers and guides.
TECHNICAL INFORMATION
Track: Aluminum 550A
Brackets: Face fix 1A/550 Joining track 3S/550 Hangers: Intermediate or end hanger for wood/ aluminum doors with 83/4" (221mm) strapbolt, no hinge 556A/221 Guides: Intermediate guide for wood doors with 515/16" (150mm) spindle, no hinge 67BA/150 End guide for wood doors with 45/16" (110mm) spindle, no hinge 68BA/110 Guide Channel: Brass 94 Aluminum 94A
Hinges:✝ 13/16" (20mm) single hinge for wood/aluminum doors 65B/20/1 13/16" (20mm) single hinge for wood/aluminum doors 65B/20 19/16" (40mm) single hinge for wood/aluminum doors 65B/40/1 19/16" (40mm) double hinge for wood/aluminum doors 65B/40 13/16"-19/16" (20-40mm) double hinge for wood/aluminum frames 65B/20-40
Accessories: Flush pull 400 Flush bolts 333/454 Narrow flush bolt and keep F3715 & F3734
* All with stainless steel strapbolt/spindle.
✝ Refer to page 110 for hinge installation.
CAPACITY
Max. door weight: 275 lbs. (125kg)
Max. door height: 14'9" (4500mm)
Max. door width: 4' (1200mm)
Door thickness: 111/16"-21/4" (43mm-57mm)
APPLICATIONS
Top-hung Flexirol gear and fittings for heavy end folding wood doors. Leaves can be hung to the left or right of an opening.
DOOR TYPES
Heavy commercial wood doors.
B and CSameWidth
F3715 67BAwith
DoubleHinge
Channel 94A
3 doors folding to the left*
Outside
InsideA B C
XEven Even
X
Door WidthA is Door
Width B or C(15mm) 9/16"
65B
65B
15/8"15/8"
(14.2)
9 16
556A/221with
DoubleHinge
Opening Width
+
XX
Opening Width25
TrackLength =OpeningWidth+25mm
65B 556A/221and
Single Hinge
F371568Band
SingleHinge
2 doors folding to the left*
Outside
InsideA BA+
15mm
(1")
(1")
(15/8") (9/16")
34 3534 35
FLEXIROL EXTERIOR ENDFOLD FOR ALUMINUM DOORS
Even
SwingDoor
Even
971 Threshold
Track 550
Track 550
67BA/220with 65BDoubleHinge
Channel 94A
Center to Center Hinge Distance
Plan: 3 doors folding to the left
Inside
Outside
Doors notby PCH
1/2"
(98.4)3 7 8
(54)2 1 8
(27)11 16
(104.8)41 8
(100)315 16
Track550A
Strap BoltStainless Steel
Hanger556A/221
Doors notby PCH
Nut M12
(20mm or 40mm)
13/16" or 19/16"
65B DoubleHinge
(20mm or 40mm)
13/16" or 19/16"
65B DoubleHinge
Lock Nut M12
Nut M12
Plastic Cover
RollerGuide
67BA/220
Lock Nut M12
(12mm)
(54)2 1 8
34 3534 35
Hinges for hangers and guides must be ordered separately.Use a single hinge for end hangers and guides, double hinge for intermediate hangers and guides.
TECHNICAL INFORMATION
Track: Aluminum 550A
Brackets: Face fix 1A/550 Joining track 3S/550 Hangers: Intermediate or end hanger for wood/ aluminum doors with 83/4" (221mm) strapbolt, no hinge 556A/221
Guides: Intermediate guide for aluminum with 515/16" (150mm) spindle, no hinge 67BA/220 End guide for aluminum doors with 45/16" (110mm) spindle, no hinge 68BA/180
Guide Channel: Brass 94 Aluminum 94A
Hinges:✝ 13/16" (20mm) single hinge for aluminum doors 65B/20/1 13/16" (20mm) double hinge for aluminum doors 65B/20 19/16" (40mm) single hinge for aluminum doors 65B/40/1 19/16" (40mm) double hinge for aluminum doors 65B/40 13/16"-19/16" (20-40mm) double hinge for aluminum frames 65B/20-40
Accessories: Flush pull 400 Flush bolts 333/454 Narrow flush bolt and keep F3715 & F3734 1/4" (7mm) packer S7
* All with stainless steel strapbolt/spindle.
✝ Refer to page 110 for hinge installation.
CAPACITY
Max. door weight: 275 lbs. (125kg)
Max. door height: 14'9" (4500mm)
Max. door width: 4' (1200mm)
Door thickness: 111/16"-21/4" (43mm-57mm)
APPLICATIONS
Top-hung Flexirol gear and fittings for end folding aluminum doors. Leaves can be hung to the left or right of an opening.
DOOR TYPES
Flexirol Exterior Endfold is suitable for aluminum doors Fixing components are not supplied as standard for aluminum doors.
Alternative Guiding System
(5)
Channel 94A
19
13/16� or 19/16�
(3/4�)
(6.4)
1 4
65BDoubleHinge
S7 Packer
67BA/220
(20mm or 40mm)
(104.8)41 8
(20.6)
13 16
(20.6)
13 16
36 3736 37
Channel 94A
Channel 94A
Insert AC115 FLI (21/550GP)
3/8"-1/2"
13/16"
3/16"
(65.1)2 9 16
(65.1)2 9 16
(71.4)213 16
(100)315 16
(33.3)1 5 16
(31.8)1 1 4
(98.4)3 7 8
(73)2 7 8
(12.7)1 2
(6.4)1 4
11 4
Hanger556
Brush
MountingBlock
InsertAC118
TopPivot
Top Glass -Clamp
Glass
(10-12mm)
SpringLoadedHinge60.12
BrushStrip
GP10 orGP12
BottomPivot
AC246(21/550GP)
FillingIn-Piece
MountingBlock
Brush
Guide104N/94
Insert - AC118 (21/550GP)
Top Pivot P117 (21/550GP)End Cap FRE12
Glass ProfileFRP02
Glass ProfileFRP02
End CapFRE13
Track 550A
(20.6)
13 16
(20.6)
13 16
FLEXIROL FOLDING GLASS CAN ALSO BE USED WITH PACER
‘Turn knob locking detail’
36 3736 37
fl20
33
73
80
Hanger556
MountingBlock
13 Clearance
GlassClamp
100
SpringLoadedHinge60.12
Track550
Rear View Front View
Top View
End FixedFace Fixed
Channel94(X)
Hanger556
Brush
MountingBlock
SpringLoadedHinge60.12
98
13
100
Top PivotP117
InsertAC118
Top Glass -Clamp
323272
10-12mmGlass
5Filling
In-Piece
Channel 94(X)
Guide104N/94
Brush
MountingBlock
Track 550
End Cap FRE 12 Top Pivot P117 (21/550GP)
Insert - AC 118 (21/550GP)
65
BrushStrip
BP010 orBP012
End CapFRE13
65Insert AC115 FLI (21/550GP)
BottomPivot
AC246(21/550GP)
H
550Track
P117+ AC118
60.12Hinge
556 Hanger
P117+ AC118
60.12Hinge
556 Hanger
104P GuideChannel 94A
*Center Fold. 31/2 Panels *End Fold. 4 Panels
Lock618
21
20
100
7
AC115 FLI+ AC246
H-240
FRP02
FRP02
21/550GPPivot Set
AC115 FLI+ AC246
Channel 94A
fl20
33
73
80
Hanger556
MountingBlock
13 Clearance
GlassClamp
100
SpringLoadedHinge60.12
Track550
Rear View Front View
Top View
End FixedFace Fixed
Channel94(X)
Hanger556
Brush
MountingBlock
SpringLoadedHinge60.12
98
13
100
Top PivotP117
InsertAC118
Top Glass -Clamp
323272
10-12mmGlass
5Filling
In-Piece
Channel 94(X)
Guide104N/94
Brush
MountingBlock
Track 550
End Cap FRE 12 Top Pivot P117 (21/550GP)
Insert - AC 118 (21/550GP)
65
BrushStrip
BP010 orBP012
End CapFRE13
65Insert AC115 FLI (21/550GP)
BottomPivot
AC246(21/550GP)
H
550Track
P117+ AC118
60.12Hinge
556 Hanger
P117+ AC118
60.12Hinge
556 Hanger
104P GuideChannel 94A
*Center Fold. 31/2 Panels *End Fold. 4 Panels
Lock618
21
20
100
7
AC115 FLI+ AC246
H-240
FRP02
FRP02
21/550GPPivot Set
AC115 FLI+ AC246
Channel 94A
CAPACITY
Max. door weight: 275 lbs. (125kg)
Max. door height: 8'2" (2500mm)
Max. door width: 2'11" (900mm)
Door thickness: 3/8"-1/2" (10mm or 12mm)
APPLICATIONS
Flexirol Folding Glass covers both center fold and end fold applications depending on the placement of the hangers within the profile.
DOOR TYPES
Glass panels of 3/8" (10mm) or 1/2" (12mm) thickness in tempered or laminated glass. All profiles for glass panels are made to measure with all necessary routing completed.
TECHNICAL INFORMATION
Track: 550A
Brackets: Face fix 1A/550 Soffit fix 3S/550 Hangers: 556 with mounting block Pivots: Glass pivot set 21/550GP
Guides: 104N/94 with mounting block Guide Channel: Brass 94 Aluminum 94A
Hinges: Adjustable face fixed, 60.12 spring-loaded hinge Accessories: Glass door lock 618 Glass door receiving lock 619
GLASS WEIGHT
3/8" glass 5.05 lbs./sq. ft.1/2" glass 6.4 lbs./sq. ft.
MountingBlock
Clearance
SpringLoadedHinge60.12
1/2"
Track 550
Face Fixed End Fixed
Top View
Front View
Rear View
Hanger556
(79.4)3 1 8
GlassClamp
(100)
60.12HInge
Lock618
21/550GPPivot Set
P117+AC118
AC115 ���+ AC2��
AC115 ���+ AC2��
P117+AC118
�0�12�i��e
55� ����e�
�����G�i�e C����e�
10�P G�i�e �����G�i�e C����e�
55� ����e�550
�� �� �
75
Answer the questions below and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware. Or use the chart on the following pages to select appropriate hardware for your job.
76
TangentUse the chart below to select appropriate hardware for your job. Or answer the questions on the previous page and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware.
HARDWARE FOR FOLDING METAL OR WOOD DOORS
Max. Door Size up to 8 ft./2'8" wide up to 8 ft./2'8" wide up to 11 ft./3ft. wide up to 11 ft./3ft. wide up to 12 ft./3ft. wide up to 12 ft./3ft. wide up to 15 ft./3ft. wide
Max. Door Weight up to 80 lbs. up to 80 lbs. up to 120 lbs. up to 120 lbs. up to 150 lbs. up to 150 lbs. up to 180 lbs.
Door Thickness 13/8-2" 13/8-2" 13/4-21/4" 13/4-21/4" 13/4-21/4" 13/4-21/4" 13/4-21/4"
SYSTEM Standard 8 ft. Deluxe 8 ft. Standard 11 ft. Deluxe 11 ft. Standard 12 ft. Deluxe 12 ft. Standard 15 ft.
Track
Brackets (one bracket for every three feet of track)
Hangers (one every two doors)
Hinges
Guides(one every two doors)
Guide Channel
Optional Extras414 flush pull
413flush pull
cane bolts
994 994R 994S
89 steel guide channel
290 301
3A/290overhead-
use for limited
installation space
1A/290sidewall-use
for limited installation
space
4R/290Soverhead-suspended
4A/290overhead-
use for ample
installation space
290
403/2 403/3
In cast aluminum alloy (deluxe=S.A.A.) or painted cast iron.
863 bow handle - 51/4"
63Kpivot hanger
65In cast aluminum alloy or painted cast iron.
3A/290overhead-
use for limited
installation space
1A/290sidewall-use
for limited installation
space
4R/290Soverhead-suspended
4A/290overhead-
use for ample
installation space
67/89 68/89
Brass roller guides mounted on alloy or cast iron hinge parts
62Kfolding pivot hanger
94A aluminum guide channel
3A/301overhead-
use for limited installation
space
1A/301sidewall-use for limited
installation space
4R/301Soverhead-suspended
4A/301overhead- use for ample
installation space
4/301Soverhead-suspended
63Apivot hanger
62Afolding pivot hanger
65In cast aluminum alloy or painted cast iron.
97 steel guide channel
400 in satin anodized aluminum
333454
464 bow handle - 101/4"
78
Jointing Brackets available for joining two pieces of track at bracet (i.e. 1AX/301)
67/94P 68/94P
Brass roller guides mounted on alloy or cast iron hinge parts (deluxe = polished aluminum)
67/97 68/97
Brass roller guides mounted on alloy or cast iron hinge parts
flush bolts
77J
414 flush pull
413flush pull
cane bolts
994 994R 994S
863 bow handle - 51/4"
400 in satin anodized aluminum
333454
464 bow handle - 101/4"
78
flush bolts
77J
414 flush pull
413flush pull
cane bolts
994 994R 994S
863 bow handle - 51/4"
400 in satin anodized aluminum
333454
464 bow handle - 101/4"
78
flush bolts
77J
63A/Ppivot hanger-polished
62A/Pfolding pivot hanger-polished
77
TangentUse the chart below to select appropriate hardware for your job. Or answer the questions on the previous page and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware.
HARDWARE FOR FOLDING METAL OR WOOD DOORS
Max. Door Size up to 8 ft./2'8" wide up to 8 ft./2'8" wide up to 11 ft./3ft. wide up to 11 ft./3ft. wide up to 12 ft./3ft. wide up to 12 ft./3ft. wide up to 15 ft./3ft. wide
Max. Door Weight up to 80 lbs. up to 80 lbs. up to 120 lbs. up to 120 lbs. up to 150 lbs. up to 150 lbs. up to 180 lbs.
Door Thickness 13/8-2" 13/8-2" 13/4-21/4" 13/4-21/4" 13/4-21/4" 13/4-21/4" 13/4-21/4"
SYSTEM Standard 8 ft. Deluxe 8 ft. Standard 11 ft. Deluxe 11 ft. Standard 12 ft. Deluxe 12 ft. Standard 15 ft.
Track
Brackets (one bracket for every three feet of track)
Hangers (one every two doors)
Hinges
Guides(one every two doors)
Guide Channel
Optional Extras
305301H301 301H
3A/301overhead-
use for limited installation
space
1A/301sidewall-use for limited
installation space
4R/301Soverhead-suspended
4A/301overhead- use for ample
installation space
4/301Soverhead-suspended
403/2 403/3
In cast aluminum alloy (deluxe=S.A.A.) or painted cast iron.
94A aluminum guide channel
3A/301overhead-
use for limited installation
space
1A/301sidewall-use for limited
installation space
4R/301Soverhead-suspended
4A/301overhead- use for ample
installation space
4/301Soverhead-suspended
63Apivot hanger
62Afolding pivot hanger
65In cast aluminum alloy or painted cast iron.
97 steel guide channel
3A/301overhead-
use for limited installation
space
1A/301sidewall-use for limited
installation space
4R/301Soverhead-suspended
4A/301overhead- use for ample
installation space
4/301Soverhead-suspended
403/2 403/3
In cast aluminum alloy (deluxe=S.A.A.) or painted cast iron.
94A aluminum guide channel
3A/305overhead-
use for limited
installation space
1A/305 sidewall-use for limited
installation space
4A/305 overhead-use for ample installation space
4R/305Soverhead-
suspended
63Cpivot hanger
62Cfolding pivot hanger
65In cast aluminum alloy or painted cast iron.
67C/97 68C/97
Brass roller guides mounted on alloy or cast iron hinge parts
97 steel guide channel
67/94P 68/94P
Brass roller guides mounted on alloy or cast iron hinge parts (deluxe = polished aluminum)
67/97 68/97
Brass roller guides mounted on alloy or cast iron hinge parts
67/94P 68/94P
Brass roller guides mounted on alloy or cast iron hinge parts (deluxe = polished aluminum)
414 flush pull
413flush pull
cane bolts
994 994R 994S
863 bow handle - 51/4"
400 in satin anodized aluminum
333454
464 bow handle - 101/4"
78
flush bolts
77J
414 flush pull
413flush pull
cane bolts
994 994R 994S
863 bow handle - 51/4"
400 in satin anodized aluminum
333454
464 bow handle - 101/4"
78
flush bolts
77J
414 flush pull
413flush pull
cane bolts
994 994R 994S
863 bow handle - 51/4"
400 in satin anodized aluminum
333454
464 bow handle - 101/4"
78
flush bolts
77J
414 flush pull
413flush pull
cane bolts
994 994R 994S
863 bow handle - 51/4"
400 in satin anodized aluminum
333454
464 bow handle - 101/4"
78
flush bolts
77J
63A/Ppivot hanger-polished
62A/Pfolding pivot hanger-polished
63A/Ppivot hanger-polished
62A/Pfolding pivot hanger-polished
78
COMPOSITION
Track and Track Curves: Cold-rolled steel section hot-dip galvanized.Brackets: Cast aluminum alloy or pressed steel, suitable for side wall or overhead fixing. Closed brackets or end-clips are available for track ends, and jointing brackets for both ends of the track curve.Hangers: Steel wheels are fitted with maintenance free precision needle bearings sealed for life. Adjustable in height. Steel parts are rustproofed by electrozinc plating or painted, and hinge parts are in cast aluminum alloy, or painted cast iron. Deluxe finish hangers have polished aluminum hinge parts.Hinges: In cast aluminum alloy or painted cast iron.Channel and Guides: Bottom channel steel section in three sizes, lugged for concrete and drilled for drainage. Brass roller guides are mounted on alloy or cast iron hinge parts Bolts, Stops andHandles: In painted or galvanized steel.
APPLICATIONS◆ The hardware is suitable for commercial or industrial Tangent doors, windows and showroom doors.◆ The doors slide clear of the opening and are parked along the side walls.◆ Openings may be covered by any number of units sliding to one or both sides.◆ Units should not be less than three panels nor more than six panels hinged together.◆ The end panel under the curve normally forms an access swing door.
For "round-the-corner" metal or wood doors, the following are included: ◆ Support brackets and track ◆ Hangers ◆ Hinges ◆ Guides ◆ Bottom channel ◆ Full range of accessories
For smooth operation, no more than six door panels should be hinged togeth-er in one unit. Doors may be panelled or flush, glazed if required, with framing and joints designed to provide suitable fixing for hinges.
TangentFOR ROUND THE CORNER WOOD OR METAL DOORS
Bracket 1A Track Curve 600
Guide 67
Channel Curve 601
Hanger 62Hanger 63
Four track sizes are available to suit doors
of different weights up to 180 lbs. 301 301H 305290
Hinge 65
Guide 68
All Dimensions in Feet and Inches
Track 290 301/301H 305
A 1/23/4 1
B 25/8 313/16 51/2
C 7/167/16
9/16
D 11/16 13/8 11/2
E 1/41/4
3/8
F 3/85/8
5/8
G 21/4 21/4 31/4
H 1 11/2 11/2
J 5/161/2
5/8
K 1 11/2 11/2
L 5/161/2
5/8
Door Type lbs./sq. ft.Hollow Metal 18 ga 4.6 lbs.Hollow Metal 16 ga 5.8 lbs.Flush Wood, Particleboard Core 4.8 lbs.Flush Wood, Stave Core 4.3 lbs.Flush Wood, Mineral Core 4.7 lbs.
Use the table below to estimate the approximate weight (pounds per square foot) of doors of different materials.
79
Answer the questions below and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware. Or use the chart on the following pages to select appropriate hardware for your job.
80
Max. Door Height up to 8ft.- System 290 up to 11 ft. - System 301 up to 12 ft. - System 301H up to 15 ft. - System 305
Max. Door Weight up to 80 lbs. 80-120 lbs. 120-150 lbs. 150-180 lbs.
Door Thickness/Width 13/8-2" thick, 32" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide
Track and Track
Curve
Brackets (one bracket for every three feet of track)
Guides (two per door)
Hangers
Hinges
Guide Channel/Channel Curve
Bow Handles, FlushPulls, Flush Bolts
Optional Extras
TangentUse the chart below to select appropriate hardware for your job. Or answer the questions on the previous page and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware.
HARDWARE KIT FOR ROUND-THE- CORNER WOOD OR METAL DOORS
3A/290overhead-use for
limited installation space
4A/290overhead-use for ample installation space
1A/290sidewall-use for
limited installation space
4R/290Soverhead-suspended
89 steel guide channel
290 301
67/89 68/89
Brass roller guides mounted on alloy or cast iron hinge parts
63Kpivot hanger(for end panel)
62Kfolding pivot hanger(1per panel joint)
65In cast aluminum alloy or painted cast iron.
414 flush pull
463 bow handle - 61/4"863 bow handle - 51/4"
400 flush pull 994R cane bolt
109 or 107stops
109
107
994X offset cane bolt
109 or 107stops
109
107
994X offset cane bolt
Jointing Brackets available for joining two pieces of track at bracet (i.e. 1AX/301)
97 steel guide channel
1A/301sidewall-use for
limited installation
space
3A/301overhead-use for
limited installation space
4A/301 overhead-use for ample installation space
4R/301Soverhead-suspended
67/97 68/97
Brass roller guides mounted on alloy or cast iron hinge parts
63Apivot hanger(for end panel)
62Afolding pivot hanger(1per panel joint)
65In cast aluminum alloy or painted cast iron.
414 flush pull
463 bow handle - 61/4"863 bow handle - 51/4"
400 flush pull 994R cane bolt
600K track curve
600B track curve
601/97 guide channel curve
601/89 guide channel curve
81
Max. Door Height up to 8ft.- System 290 up to 11 ft. - System 301 up to 12 ft. - System 301H up to 15 ft. - System 305
Max. Door Weight up to 80 lbs. 80-120 lbs. 120-150 lbs. 150-180 lbs.
Door Thickness/Width 13/8-2" thick, 32" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide
Track and Track
Curve
Brackets (one bracket for every three feet of track)
Guides (two per door)
Hangers
Hinges
Guide Channel/Channel Curve
Bow Handles, FlushPulls, Flush Bolts
Optional Extras
TangentUse the chart below to select appropriate hardware for your job. Or answer the questions on the previous page and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware.
HARDWARE KIT FOR ROUND-THE- CORNER WOOD OR METAL DOORS
3A/305 overhead-use for limited
installation space
4R/305Soverhead-suspended
1A/305sidewall-use for
limited installation space
305301H
4A/305overhead-use for ample installation space
109 or 107stops
109
107
994X offset cane bolt
109 or 107stops
109
107
994X offset cane bolt
414 flush pull
463 bow handle - 61/4"863 bow handle - 51/4"
400 flush pull 994R cane bolt
413 flush pull463 bow handle - 61/4" 994R cane bolt
97 steel guide channel
1A/301sidewall-use for
limited installation
space
3A/301overhead-use for
limited installation space
4A/301 overhead-use for ample installation space
4R/301Soverhead-suspended
63Apivot hanger(for end panel)
62Afolding pivot hanger(1per panel joint)
65In cast aluminum alloy or painted cast iron.
67/97 68/97
Brass roller guides mounted on alloy or cast iron hinge parts
63Cpivot hanger(for end panel)
62Cfolding pivot hanger(1per panel joint)
65In cast aluminum alloy or painted cast iron.
67C/97 68C/97
Brass roller guides mounted on alloy or cast iron hinge parts
97 steel guide channel
600BHtrack curve
600Dtrack curve
601/97 guide channel curve
601/97 guide channel curve
82
Council290-305FOR END FOLDING WOOD PARTITION DOORS
Bracket 3A
Hanger 21
Flush Bolt
Guide Channel
Hinge 403
Flush Pull 400
Guide 21
Track
APPLICATIONS◆ The hardware is suitable for residential, commercial and public buildings where concealed fixing of the fittings is required. ◆ Only the neat flush pulls and bolts are visible on the face of the screen. ◆ Folding units should consist of an even number of panels up to a maximum of six hinged to jamb or anchored by pivots.◆ For wide openings, the center units may be "floating" and these should consist of four or six panels. ◆ A swing door independently hinged to post is recommended for easy access, or alternatively one can be added to a two or four panel unit. Avoid these on partitions over 10" high and if access is required a wicket door should be arranged.
COMPOSITION
Track: Cold-rolled steel section hot-dip galvanized.Brackets: Cast aluminum or pressed steel electrozinc plated finish. Suitable brackets available for side wall or overhead fixing as well as closed brackets for each end.Hangers: Fitted with maintenance free precision needle bearings sealed for life. Adjustable in height. Steel wheels and other parts are electrozinc plated.Hinges: Aluminum alloy satin anodized finish. For economy, specify electrozinc plated steel hinges.Guides: Brass rollers fitted to steel aprons which are electrozinc plated.Guide Channel: Brass or aluminum drilled and counter-sunk for wood or lugged for concrete.Pivot Set (if required): Comprises a top pivot, standard bottom guide and alternative sockets for wood or concrete floors.Flush Pulls and Bolts: In satin anodized aluminum.
Door Type lbs./sq. ft.Hollow Metal 18 ga 4.6 lbs.Hollow Metal 16 ga 5.8 lbs.Flush Wood, Particleboard Core 4.8 lbs.Flush Wood, Stave Core 4.3 lbs.Flush Wood, Mineral Core 4.7 lbs.
Use the table below to estimate the approximate weight (pounds per square foot) of doors of different materials.
For flush end-folding wood doors, the following are included: ◆ Support brackets and track ◆ Hangers ◆ Hinges ◆ Guides ◆ Bottom channel ◆ Full range of accessories
For smooth operation, the recommended maximum number of panels in one unit is six hinged to jamb. If the panels are all of equal width and are required to be anchored at one end, Council "Flush fold pivot" hardware can be used. Panels may be panelled, glazed or flush and should be constructed with solid top and bottom rails to provide a secure fixing for edge fit-ting, hangers and guides.
All Dimensions in Feet and Inches
Track 290 301/301H 305
A 21/2 4 5
B 31/4 51/8 65/8
C 23/16 33/8 43/4
D 3/4 13/8 23/8
E 1/211/16
11/16
F 41/2 51/4 51/4
G 11/2 13/4 13/4
H 19/16 17/8
J 3/4 13/8
K 19/16 17/8
L 23/4 3
M1 5/161/2
5/8
M2 1/25/8
5/8
M3 1/45/16
Use in Place of401/402/403 Hinges:
PemkoHinge™Continuous Geared
Aluminum Hinges
301 301H 305290
Four track sizes are available to suit doors
of different weights up to 180 lbs.
83
Answer the questions below and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware. Or use the chart on the following pages to select appropriate hardware for your job.
84
Max. Door Height up to 9ft.- System 290 up to 11 ft. - System 301 up to 12 ft. - System 301H up to 15 ft. - System 305
Max. Door Weight up to 80 lbs. 80-120 lbs. 120-150 lbs. 150-180 lbs.
Door Thickness/Width 13/8-13/4" thick, 32" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide
Track
Brackets (one bracket for every three feet of track)
Guides (two per door)
Hangers
Hinges, Pivots
Guide Channel
Flush Pulls, Flush Bolts
Optional Extras
Council 290-305Use the chart below to select appropriate hardware for your job. Or answer the questions on the previous page and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware.
HARDWARE FOR END FOLDING WOOD PARTITION DOORS
3A/290overhead-use for
limited installation space
4A/290overhead-use for ample installation space
1A/290sidewall-use for
limited installation space
290 301
1A/301sidewall-use for
limited installation
space
3A/301overhead-use for
limited installation space
21K/Sendfold hanger (1 for every 2 panels)
403/1
In cast aluminum alloy (deluxe=S.A.A.) or painted cast iron.
21K/Pendfold pivot
top bottom
94 brass guide channel
94A aluminum guide channel
21K/4Nto be used adjacent to swing door
414 flush pull 400 flush pull 454 flush bolt 333 flush bolt
113Rguide
113Rguide
1/301EC end clip for 301 steel brackets (1A/301 end clips also available for aluminum brackets)
4A/301overhead-use for ample installation space
21A/Sendfold hanger (1 for every 2 panels)
21A/4Sto be used adjacent to swing door
topbottom
403/2
In cast aluminum alloy (deluxe=S.A.A.) or painted cast iron.
21A/Pendfold pivot
top bottom
94 brass guide channel
94A aluminum guide channel
414 flush pull 400 flush pull 454 flush bolt 333 flush bolt
1/290EC (not shown)end clip for 290 steel brackets (1A/290 end clips also available for aluminum brackets)
21KR/94guide
21KR/94guide
21R endfold guide
21R endfold guide
85
Max. Door Height up to 9ft.- System 290 up to 11 ft. - System 301 up to 12 ft. - System 301H up to 15 ft. - System 305
Max. Door Weight up to 80 lbs. 80-120 lbs. 120-150 lbs. 150-180 lbs.
Door Thickness/Width 13/8-13/4" thick, 32" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide
Track
Brackets (one bracket for every three feet of track)
Guides (two per door)
Hangers
Hinges, Pivots
Guide Channel
Flush Pulls, Flush Bolts
Optional Extras
Council 290-305Use the chart below to select appropriate hardware for your job. Or answer the questions on the previous page and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware.
HARDWARE FOR END FOLDING WOOD PARTITION DOORS
3A/305 overhead-use for limited
installation space
1A/305sidewall-use for
limited installation space
305301H
4A/305overhead-use for ample installation space
113Rguide
1/301EC end clips for 301 steel brackets (1A/301 end clips also available for aluminum brackets)
113Rguide
3A/301overhead-use for
limited installation space
4A/301overhead-use for ample installation space
21A/Sendfold hanger (1 for every 2 panels)
21A/4Sto be used adjacent to swing door
topbottom
403/2
In cast aluminum alloy (deluxe=S.A.A.) or painted cast iron.
21A/Pendfold pivot
top bottom
94 brass guide channel
94A aluminum guide channel
414 flush pull 400 flush pull 454 flush bolt 333 flush bolt
1A/301sidewall-use for
limited installation
space
21C/Sendfold hanger (1 for every 2 panels)
403/3
In cast aluminum alloy (deluxe=S.A.A.) or painted cast iron.
94 brass guide channel
94A aluminum guide channel
414 flush pull 400 flush pull 454 flush bolt
21KR/94guide
21KR/94guide
21R endfold guide
21R endfold guide
86
Track 290 301/301H 305
A 21/2 4 5
B 31/4 51/8 65/8
C 23/16 33/8 43/4
D 3/4 13/8 23/8
E 11/2 2 21/2
F 1/23/4
3/4
G 5/161/2
5/8
H 17/8 3 31/4
J 25/8 33/4 53/8
K 51/2 71/4 91/2
Council290-305FOR CENTER FOLDING WOOD PARTITION DOORS
Bracket 3A
Hanger 61
Flush Bolt
Guide Channel
Hinge 403
Flush Pull 400
Guide 106R/94
Track
APPLICATIONS◆ The hardware is suitable for residential, commercial and public buildings. ◆ Partitions are usually hung centrally under the lintel and fold to one or both sides, occupying a minimum of space during closing operation. ◆ The folding units should consist of an odd number of full panels with one half panel hinged to jamb. ◆ For wide openings, the center units may be "floating" and consist of five or seven panels in one unit. ◆ Where an access door is required this may be hung separately to the jamb and not form part of the folding unit, or a wicket door should be arranged in one panel.
COMPOSITION
Track: Cold-rolled steel section hot-dip galvanized.Brackets: These are of cast aluminum or pressed steel. Suitable brackets are available overhead fixing as well as closed brackets for each end.Hangers: These are fitted with maintenance free precision needle bearings sealed for life. Adjustable in height. Steel wheels and other parts are electrozinc plated.Hinges: Aluminum alloy satin anodized finish. For economy, specify electrozinc plated steel hinges.Guides: Brass rollers fitted to steel plates which are electrozinc plated.Channel: Brass or aluminum drilled and counter-sunk for wood or lugged for concrete.Flush Pulls and Bolts: In satin anodized aluminum.
For center-folding wood doors, the following are included: ◆ Support brackets and track ◆ Hangers ◆ Hinges ◆ Guides ◆ Bottom channel ◆ Full range of accessories
For smooth operation, the recommended maximum num-ber of panels in one unit is five and a half hinged to jamb. Panels may be panelled, glazed or flush and should be constructed with solid top and bot-
All Dimensions in Feet and Inches
Use in Place of401/402/403 Hinges:
PemkoHinge™Continuous Geared
Aluminum Hinges
Door Type lbs./sq. ft.Hollow Metal 18 ga 4.6 lbs.Hollow Metal 16 ga 5.8 lbs.Flush Wood, Particleboard Core 4.8 lbs.Flush Wood, Stave Core 4.3 lbs.Flush Wood, Mineral Core 4.7 lbs.
Use the table below to estimate the approximate weight (pounds per square foot) of doors of different materials.
301 301H 305290
Four track sizes are available to suit doors
of different weights up to 180 lbs.
87
Answer the questions below and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware. Or use the chart on the following pages to select appropriate hardware for your job.
88
Max. Door Height up to 9ft.- System 290 up to 11 ft. - System 301 up to 12 ft. - System 301H up to 15 ft. - System 305
Max. Door Weight up to 80 lbs. 80-120 lbs. 120-150 lbs. 150-180 lbs.
Door Thickness/Width 13/8-13/4" thick, 32" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide
Track
Brackets (one bracket for every three feet of track)
Guides (two per door)
Hangers
Hinges, Pivots
Guide Channel
Flush Pulls, Flush Bolts
Optional Extras
Council 290-305Use the chart below to select appropriate hardware for your job. Or answer the questions on the previous page and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware.
HARDWARE FOR CENTER FOLDING WOOD PARTITION DOORS
3A/290overhead-use for
limited installation space
4A/290overhead-use for ample installation space
1A/290sidewall-use for
limited installation space
290 301
3A/301overhead-use for
limited installation space
1A/301sidewall-use for
limited installation
space
21K/Sendfold hanger (1 for every 2 panels)
403/1
In cast aluminum alloy (deluxe=S.A.A.) or painted cast iron.
21K/Pendfold pivot
top bottom
94 brass guide channel
414 flush pull 400 flush pull 454 flush bolt 333 flush bolt
94A aluminum guide channel
21K/4Nto be used adjacent to swing door
113Rguide
4A/301overhead-use for ample installation space
1A/301EC end clips for 301 brackets
113Rguide
top bottom
1A/301EC end clips for 301 brackets
414 flush pull 400 flush pull 454 flush bolt 333 flush bolt
21A/Sendfold hanger (1 for every 2 panels)
21A/4Sto be used adjacent to swing door
403/2
In cast aluminum alloy (deluxe=S.A.A.) or painted cast iron.
21A/Pendfold pivot
top bottom
94 brass guide channel
94A aluminum guide channel
21KR/94guide
21R/94guide
21R endfold guide
21R endfold guide
topbottom
89
Max. Door Height up to 9ft.- System 290 up to 11 ft. - System 301 up to 12 ft. - System 301H up to 15 ft. - System 305
Max. Door Weight up to 80 lbs. 80-120 lbs. 120-150 lbs. 150-180 lbs.
Door Thickness/Width 13/8-13/4" thick, 32" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide 13/4-21/4" thick, 36" wide
Track
Brackets (one bracket for every three feet of track)
Guides (two per door)
Hangers
Hinges, Pivots
Guide Channel
Flush Pulls, Flush Bolts
Optional Extras
Council 290-305Use the chart below to select appropriate hardware for your job. Or answer the questions on the previous page and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware.
HARDWARE FOR CENTER FOLDING WOOD PARTITION DOORS
3A/305 overhead-use for limited
installation space
1A/305sidewall-use for
limited installation space
305301H
4A/305overhead-use for ample installation space
113Rguide
1A/301EC end clips for 301 brackets
113Rguide
1A/301EC end clips for 301 brackets
4A/301overhead-use for ample installation space
3A/301overhead-use for
limited installation space
top bottom
21A/Sendfold hanger (1 for every 2 panels)
414 flush pull 400 flush pull 454 flush bolt
21A/4Sto be used adjacent to swing door
403/2
In cast aluminum alloy (deluxe=S.A.A.) or painted cast iron.
21A/Pendfold pivot
top bottom
94 brass guide channel
94A aluminum guide channel
414 flush pull 400 flush pull 454 flush bolt 333 flush bolt
1A/301sidewall-use for
limited installation
space
21C/Sendfold hanger (1 for every 2 panels)
403/3
In cast aluminum alloy (deluxe=S.A.A.) or painted cast iron.
94 brass guide channel
94A aluminum guide channel
21R/94guide
21R/94guide
21R endfold guide
21R endfold guide
topbottom
90
ArcadeA70FOR END AND CENTER FOLDING ALUMINUM AND WOOD SECTION DOORS
Bracket 3/900 Top Guide Channel 900
Brass Bottom Rail 918
Glazing
Bottom Roller 922 or 923
Top Guide Roller 902
APPLICATIONS◆ High-quality bottom roller hardware and fittings for end and center folding aluminum section glazed for retail and display applications to a maximum leaf weight of 150 lbs.
For end folding and center folding aluminum and wood par-tition doors, the following are included: ◆ Top guide brackets ◆ Bottom rollers ◆ Top guide channel ◆ Bottom rail ◆ Top guide rollers ◆ Full range of accessories ◆ Back flap hinges
For best endfold operation, not more than 8 leaves should be hinged to one jamb; alternatively leaves may be floating in units of 6 or 8. Any access door should be hung sepa-rately to the jamb. For best centerfold operation, not more than 71/2 leaves to be hinged to one jamb; alter-natively leaves may be floating in units of 5 or 7. Any access door should be hung separately to the jamb.
Use in Place of401/402/403 Hinges:
PemkoHinge™Continuous Geared
Aluminum Hinges
COMPOSITION
Top Guide Channel: 900 galvanized steel with safety lip.Top Guide Brackets: Pressed steel zinc plated.Top Guide Rollers: Fitted with adjustable nylon rollers. Vertical adjustment is simple and positive.Bottom Rollers: Supported on thrust bearings.Hinges: Proprietary hinges used to suit the aluminum rails and stile used to construct the leaves.Rail: Pre-drilled and countersunk for wood or lugging into concrete.Accessories: Flush Pulls, Flush Bolts and Locks.
Door Type lbs./sq. ft.Hollow Metal 18 ga 4.6 lbs.Hollow Metal 16 ga 5.8 lbs.Flush Wood, Particleboard Core 4.8 lbs.Flush Wood, Stave Core 4.3 lbs.Flush Wood, Mineral Core 4.7 lbs.
Use the table below to estimate the approximate weight (pounds per square foot) of doors of different materials.
91
Answer the questions below and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware. Or use the chart on the following pages to select appropriate hardware for your job.
92
Max. Folding Leaf Height up to 12 ft. - Endfold System A70 up to 12 ft. - Centerfold System A70
Max. Door Weight up to 150 lbs. up to 150 lbs.
Door Thickness/Width 13/4-17/8", 2'8" wide 13/4-17/8", 3' wide
Top Guide Channel
Brackets (fix every 3' max and at channel joints. Fix extra bracket where doors stack)
Top Guide Rollers (one every two doors)
Hinges (three in height)
Bottom Rollers (one every two doors)
Bottom Rail
Flush Pull
Flush Bolt
Arcade A70Use the chart below to select appropriate hardware for your job. Or answer the questions on the previous page and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware.
HARDWARE FOR END AND CENTER FOLDING ALUMINUM AND WOOD SECTION DOORS
3/900overhead-use for limited installation space
1/900sidewall-use for limited installation space
400 flush pull
454 flush bolt
65/65P hinge
902comes with flat mounting plate (not shown)
918 brass bottom rail
900
922for aluminum doors
923for wood doors
93
Max. Folding Leaf Height up to 12 ft. - Endfold System A70 up to 12 ft. - Centerfold System A70
Max. Door Weight up to 150 lbs. up to 150 lbs.
Door Thickness/Width 13/4-17/8", 2'8" wide 13/4-17/8", 3' wide
Top Guide Channel
Brackets (fix every 3' max and at channel joints. Fix extra bracket where doors stack)
Top Guide Rollers (one every two doors)
Hinges (three in height)
Bottom Rollers (one every two doors)
Bottom Rail
Flush Pull
Flush Bolt
Arcade A70Use the chart below to select appropriate hardware for your job. Or answer the questions on the previous page and fax (800-283-4050) or call (800-283-9988) Pemko Customer Service for assistance with choosing your hardware.
HARDWARE FOR END AND CENTER FOLDING ALUMINUM AND WOOD SECTION DOORS
3/900overhead-use for limited installation space
1/900sidewall-use for limited installation space
400 flush pull
454 flush bolt
65/65P hinge
902comes with flat mounting plate (not shwon)
918 brass bottom rail
900
922for aluminum doors
923for wood doors
110 111110 111
3
3
7
15
Hinge65B
40 40
20
20
3
20
5
CramPlate
Rubber Sealingnot by PCH
Door Just Folding
20 40
3
40
520
35
Distance from the edge of thedoor leaf to the centre of the hinge
Standard Fixing to Post(Flush) Hinge 65B/40
*Double SealedDoor
Standard Fixing to Post(Flush) Hinge 65B/20-40
Standard Fixing to Post(Flush) Hinge 65B/20
*SingleSealedDoor
Hinge65B/40
Hinge65B/20-40
Hinge65B/20
(19/16")
(3/16")
(13/16")
(1/8")
(1/8")
(13/16")(13/8")
(3/16")
(13/16") (19/16")
(19/16")
(13/16")
(19/16")
(9/16")
(1/8")
(1/8")
(1/4")
(13/16")
H I N G E I N S TA L L AT I O N
65B/20
85
23
20
65B/40
40
23
85
65B/20-40
23
20
85
40
40 40 40
11090
70
35 20
(19/16")
(7/8") (33/8")
(19/16")
(45/16")
(7/8")
(13/16")
(19/16")
(33/8")
(19/16")
(31/2")
(13/8")
(23/4")
(13/16")
(19/16")(13/16")
(7/8")
(33/8")
H I N G E SCOMPONENTS
110 111110 1113S/5501A/550
280 A
600 FP 600 CFP
45 O
Pacer Curve 600 C
Face Fix Bracket 281
(Bottom View) (Bottom View)
550 Track 600 Track52
55.5
100
Bolt NotSuppliedby PCH
Bolt NotSuppliedby PCH
Pacer Switch 45R/600 Pacer Switch 45L/600350 350
14.0
Thr
ough
out
R 374
91
79.5
85.5
38
Jointing Bracket 1BX
fl 9
Bracket 1B
20
fl 9
13
80
7
40
25
20
40
34
33
24
34
48
40
48
34
70
13
140
70
70
100-1000
100
6
6
29
20
20
29
2
73
98
(15/16")
(15/16")
(33/8")
(11/2")
(15/16")
(21/16")
(23/16")
(31/8")
(39/16")
(19/16")
(133/4") (133/4")
(17/8")
(15/16")
(13/16")
(1/2")
(19/16")
(3/8")
(17/8")
(15/16")
(23/4")
(1/2")(3/8")
(315/16") (31/8")
(315/16")
(315/16"-393/8")
(23/4")
(23/4")
(51/2")
(19/16")
(1")(1/4")
(13/16")
(13/16")
(11/8")
(1/4")
(1/4") (11/8")
(13/16")
(1/16")
(37/8")
(27/8")
Pacer
Bracket 1B
Pacer
Jointing Bracket 1BX
B R AC K E T S
v
3S/5501A/550
280 A
600 FP 600 CFP
45 O
Pacer Curve 600 C
Face Fix Bracket 281
(Bottom View) (Bottom View)
550 Track 600 Track52
55.5
100
Bolt NotSuppliedby PCH
Bolt NotSuppliedby PCH
Pacer Switch 45R/600 Pacer Switch 45L/600350 350
14.0
Thr
ough
out
R 374
91
79.5
85.5
38
Jointing Bracket 1BX
fl 9
Bracket 1B
20
fl 9
13
80
7
40
25
20
40
34
33
24
34
48
40
48
34
70
13
140
70
70
100-1000
100
6
6
29
20
20
29
2
73
98
(15/16")
(15/16")
(33/8")
(11/2")
(15/16")
(21/16")
(23/16")
(31/8")
(39/16")
(19/16")
(133/4") (133/4")
(17/8")
(15/16")
(13/16")
(1/2")
(19/16")
(3/8")
(17/8")
(15/16")
(23/4")
(1/2")(3/8")
(315/16") (31/8")
(315/16")
(315/16"-393/8")
(23/4")
(23/4")
(51/2")
(19/16")
(1")(1/4")
(13/16")
(13/16")
(11/8")
(1/4")
(1/4") (11/8")
(13/16")
(1/16")
(37/8")
(27/8")
3S/5501A/550
280 A
600 FP 600 CFP
45 O
Pacer Curve 600 C
Face Fix Bracket 281
(Bottom View) (Bottom View)
550 Track 600 Track52
55.5
100
Bolt NotSuppliedby PCH
Bolt NotSuppliedby PCH
Pacer Switch 45R/600 Pacer Switch 45L/600350 350
14.0
Thr
ough
out
R 374
91
79.5
85.5
38
Jointing Bracket 1BX
fl 9
Bracket 1B
20
fl 9
13
80
7
40
25
20
40
34
33
24
34
48
40
48
34
70
13
140
70
70
100-1000
100
6
6
29
20
20
29
2
73
98
(15/16")
(15/16")
(33/8")
(11/2")
(15/16")
(21/16")
(23/16")
(31/8")
(39/16")
(19/16")
(133/4") (133/4")
(17/8")
(15/16")
(13/16")
(1/2")
(19/16")
(3/8")
(17/8")
(15/16")
(23/4")
(1/2")(3/8")
(315/16") (31/8")
(315/16")
(315/16"-393/8")
(23/4")
(23/4")
(51/2")
(19/16")
(1")(1/4")
(13/16")
(13/16")
(11/8")
(1/4")
(1/4") (11/8")
(13/16")
(1/16")
(37/8")
(27/8")
3S/5501A/550
280 A
600 FP 600 CFP
45 O
Pacer Curve 600 C
Face Fix Bracket 281
(Bottom View) (Bottom View)
550 Track 600 Track52
55.5
100
Bolt NotSuppliedby PCH
Bolt NotSuppliedby PCH
Pacer Switch 45R/600 Pacer Switch 45L/600350 350
14.0
Thr
ough
out
R 374
91
79.5
85.5
38
Jointing Bracket 1BX
fl 9
Bracket 1B
20
fl 9
13
80
7
40
25
20
40
34
33
24
34
48
40
48
34
70
13
140
70
70
100-1000
100
6
6
29
20
20
29
2
73
98
(15/16")
(15/16")
(33/8")
(11/2")
(15/16")
(21/16")
(23/16")
(31/8")
(39/16")
(19/16")
(133/4") (133/4")
(17/8")
(15/16")
(13/16")
(1/2")
(19/16")
(3/8")
(17/8")
(15/16")
(23/4")
(1/2")(3/8")
(315/16") (31/8")
(315/16")
(315/16"-393/8")
(23/4")
(23/4")
(51/2")
(19/16")
(1")(1/4")
(13/16")
(13/16")
(11/8")
(1/4")
(1/4") (11/8")
(13/16")
(1/16")
(37/8")
(27/8")
3S/5501A/550
280 A
600 FP 600 CFP
45 O
Pacer Curve 600 C
Face Fix Bracket 281
(Bottom View) (Bottom View)
550 Track 600 Track52
55.5
100
Bolt NotSuppliedby PCH
Bolt NotSuppliedby PCH
Pacer Switch 45R/600 Pacer Switch 45L/600350 350
14.0
Thr
ough
out
R 374
91
79.5
85.5
38
Jointing Bracket 1BX
fl 9
Bracket 1B
20
fl 9
13
80
7
40
25
20
40
34
33
24
34
48
40
48
34
70
13
140
70
70
100-1000
100
6
6
29
20
20
29
2
73
98
(15/16")
(15/16")
(33/8")
(11/2")
(15/16")
(21/16")
(23/16")
(31/8")
(39/16")
(19/16")
(133/4") (133/4")
(17/8")
(15/16")
(13/16")
(1/2")
(19/16")
(3/8")
(17/8")
(15/16")
(23/4")
(1/2")(3/8")
(315/16") (31/8")
(315/16")
(315/16"-393/8")
(23/4")
(23/4")
(51/2")
(19/16")
(1")(1/4")
(13/16")
(13/16")
(11/8")
(1/4")
(1/4") (11/8")
(13/16")
(1/16")
(37/8")
(27/8")
3S/5501A/550
280 A
600 FP 600 CFP
45 O
Pacer Curve 600 C
Face Fix Bracket 281
(Bottom View) (Bottom View)
550 Track 600 Track52
55.5
100
Bolt NotSuppliedby PCH
Bolt NotSuppliedby PCH
Pacer Switch 45R/600 Pacer Switch 45L/600350 350
14.0
Thr
ough
out
R 374
91
79.5
85.5
38
Jointing Bracket 1BX
fl 9
Bracket 1B
20
fl 9
13
80
7
40
25
20
40
34
33
24
34
48
40
48
34
70
13
140
70
70
100-1000
100
6
6
29
20
20
29
2
73
98
(15/16")
(15/16")
(33/8")
(11/2")
(15/16")
(21/16")
(23/16")
(31/8")
(39/16")
(19/16")
(133/4") (133/4")
(17/8")
(15/16")
(13/16")
(1/2")
(19/16")
(3/8")
(17/8")
(15/16")
(23/4")
(1/2")(3/8")
(315/16") (31/8")
(315/16")
(315/16"-393/8")
(23/4")
(23/4")
(51/2")
(19/16")
(1")(1/4")
(13/16")
(13/16")
(11/8")
(1/4")
(1/4") (11/8")
(13/16")
(1/16")
(37/8")
(27/8")
T R AC K , I N T E R S E C T S A N D C U RV E S
FLEXIROL 555 JUNCTIONS/INTERSECTS
Husky Pacer Pacer Pacer Flexirol
�
����������������������
�������
����������
��������������������������
�������������
�������
�������������
�������
������
�������������
�������
90ß 90ß90ß
90ß Elbow
551H/90 Jointing Strip
H90/550
90ß T-Junction
552H/90 Track/Hanger Guide
JointingStrip
551/180
JointingStrip
551H/90
TW/550
JointingStrip
551/180
FLEXIROL 556 JUNCTIONS/INTERSECTS(Top Views)
PACER CURVES/INTERSECTS(Bottom Views)
3S/5501A/550
280 A
600 FP 600 CFP
45 O
Pacer Curve 600 C
Face Fix Bracket 281
(Bottom View) (Bottom View)
550 Track 600 Track52
55.5
100
Bolt NotSuppliedby PCH
Bolt NotSuppliedby PCH
Pacer Switch 45R/600 Pacer Switch 45L/600350 350
14.0
Thr
ough
out
R 374
91
79.5
85.5
38
Jointing Bracket 1BX
fl 9
Bracket 1B
20
fl 9
13
80
7
40
25
20
40
34
33
24
34
48
40
48
34
70
13
140
70
70
100-1000
100
6
6
29
20
20
29
2
73
98
(15/16")
(15/16")
(33/8")
(11/2")
(15/16")
(21/16")
(23/16")
(31/8")
(39/16")
(19/16")
(133/4") (133/4")
(17/8")
(15/16")
(13/16")
(1/2")
(19/16")
(3/8")
(17/8")
(15/16")
(23/4")
(1/2")(3/8")
(315/16") (31/8")
(315/16")
(315/16"-393/8")
(23/4")
(23/4")
(51/2")
(19/16")
(1")(1/4")
(13/16")
(13/16")
(11/8")
(1/4")
(1/4") (11/8")
(13/16")
(1/16")
(37/8")
(27/8")
3S/5501A/550
280 A
600 FP 600 CFP
45 O
Pacer Curve 600 C
Face Fix Bracket 281
(Bottom View) (Bottom View)
550 Track 600 Track52
55.5
100
Bolt NotSuppliedby PCH
Bolt NotSuppliedby PCH
Pacer Switch 45R/600 Pacer Switch 45L/600350 350
14.0
Thr
ough
out
R 374
91
79.5
85.5
38
Jointing Bracket 1BX
fl 9
Bracket 1B
20
fl 9
13
80
7
40
25
20
40
34
33
24
34
48
40
48
34
70
13
140
70
70
100-1000
100
6
6
29
20
20
29
2
73
98
(15/16")
(15/16")
(33/8")
(11/2")
(15/16")
(21/16")
(23/16")
(31/8")
(39/16")
(19/16")
(133/4") (133/4")
(17/8")
(15/16")
(13/16")
(1/2")
(19/16")
(3/8")
(17/8")
(15/16")
(23/4")
(1/2")(3/8")
(315/16") (31/8")
(315/16")
(315/16"-393/8")
(23/4")
(23/4")
(51/2")
(19/16")
(1")(1/4")
(13/16")
(13/16")
(11/8")
(1/4")
(1/4") (11/8")
(13/16")
(1/16")
(37/8")
(27/8")
3S/5501A/550
280 A
600 FP 600 CFP
45 O
Pacer Curve 600 C
Face Fix Bracket 281
(Bottom View) (Bottom View)
550 Track 600 Track52
55.5
100
Bolt NotSuppliedby PCH
Bolt NotSuppliedby PCH
Pacer Switch 45R/600 Pacer Switch 45L/600350 350
14.0
Thr
ough
out
R 374
91
79.5
85.5
38
Jointing Bracket 1BX
fl 9
Bracket 1B
20
fl 9
13
80
7
40
25
20
40
34
33
24
34
48
40
48
34
70
13
140
70
70
100-1000
100
6
6
29
20
20
29
2
73
98
(15/16")
(15/16")
(33/8")
(11/2")
(15/16")
(21/16")
(23/16")
(31/8")
(39/16")
(19/16")
(133/4") (133/4")
(17/8")
(15/16")
(13/16")
(1/2")
(19/16")
(3/8")
(17/8")
(15/16")
(23/4")
(1/2")(3/8")
(315/16") (31/8")
(315/16")
(315/16"-393/8")
(23/4")
(23/4")
(51/2")
(19/16")
(1")(1/4")
(13/16")
(13/16")
(11/8")
(1/4")
(1/4") (11/8")
(13/16")
(1/16")
(37/8")
(27/8")
H90/550
45R/550Intersect
Right
45L/550Intersect
Left
(Top View) (Top View)
551/180
551H/45551H/135
Track Hanger Guide 552H/135
551/180
551H/135 551/180551H/135
45R/55045R/550Intersect
Right
45L/550Intersect
Left
(Top View) (Top View)
551/180
551H/45551H/135
Track Hanger Guide 552H/135
551/180
551H/135 551/180551H/135
45R/550Intersect
Right
45L/550Intersect
Left
(Top View) (Top View)
551/180
551H/45551H/135
Track Hanger Guide 552H/135
551/180
551H/135 551/180551H/135
45R/550Intersect
Right
45L/550Intersect
Left
(Top View) (Top View)
551/180
551H/45551H/135
Track Hanger Guide 552H/135
551/180
551H/135 551/180551H/135
TW/550
Pacer track supplied in mill finish as standard. Flexirol track supplied in mill finish and RAL 9010 as standard.
45L/550 H135/550 H90C/550
112 113112 113
H A N G E R S
57B
25
561/2B56B 56BX
HENDERSON
90
62BA/148
61B61B/4
52B
HENDERSON
HENDERSON
HENDERSON
HENDERSON
HENDERSON
HENDERSON
HENDERSON
21B 21B/4 21B0/4
63BA/10463B0A/114 63BA/20562BA/250
205
12
90
fl10
148
12
250
909090
fl10
114
fl10
90
104
25
38 38
140
65
5
185
5
124
133
25
13
155
1325 25 13
(39/16")90
(29/16")65
(51/2")
(39/16")
(29/16")
(51/2")139
(1")
(75/16")185
(3/16")(75/16")
(3/16") (51/4")
(1")
(47/8")
(11/2")
(6")152
(61/8")
(11/2")
(6")
(61/8")
152
38
155
(11/2")
(6")
(61/8")
152
155
(1") (1/2") (1") (1/2") (1") (1/2")
(39/16")
(41/2")
(3/8") (3/8")
(3/8")
(39/16") (39/16") (39/16") (39/16")
(41/8")(513/16")
(913/16")
(1/2")
(1/2")
(81/16")
(1/2")
25.4
35
21B/MD
12.7
76
152.5
152.5
61B/MD
34.5
76
140
25
(3")
(13/8")
(51/2")
(1") (6")
(6")
(1")
(3")
(13/8")
PACER HANGERS
B R AC K E T S
3S/5501A/550
280 A
600 FP 600 CFP
45 O
Pacer Curve 600 C
Face Fix Bracket 281
(Bottom View) (Bottom View)
550 Track 600 Track52
55.5
100
Bolt NotSuppliedby PCH
Bolt NotSuppliedby PCH
Pacer Switch 45R/600 Pacer Switch 45L/600350 350
14.0
Thr
ough
out
R 374
91
79.5
85.5
38
Jointing Bracket 1BX
fl 9
Bracket 1B
20
fl 9
13
80
7
40
25
20
40
34
33
24
34
48
40
48
34
70
13
140
70
70
100-1000
100
6
6
29
20
20
29
2
73
98
(15/16")
(15/16")
(33/8")
(11/2")
(15/16")
(21/16")
(23/16")
(31/8")
(39/16")
(19/16")
(133/4") (133/4")
(17/8")
(15/16")
(13/16")
(1/2")
(19/16")
(3/8")
(17/8")
(15/16")
(23/4")
(1/2")(3/8")
(315/16") (31/8")
(315/16")
(315/16"-393/8")
(23/4")
(23/4")
(51/2")
(19/16")
(1")(1/4")
(13/16")
(13/16")
(11/8")
(1/4")
(1/4") (11/8")
(13/16")
(1/16")
(37/8")
(27/8")
3S/5501A/550
280 A
600 FP 600 CFP
45 O
Pacer Curve 600 C
Face Fix Bracket 281
(Bottom View) (Bottom View)
550 Track 600 Track52
55.5
100
Bolt NotSuppliedby PCH
Bolt NotSuppliedby PCH
Pacer Switch 45R/600 Pacer Switch 45L/600350 350
14.0
Thr
ough
out
R 374
91
79.5
85.5
38
Jointing Bracket 1BX
fl 9
Bracket 1B
20
fl 9
13
80
7
40
25
20
40
34
33
24
34
48
40
48
34
70
13
140
70
70
100-1000
100
6
6
29
20
20
29
2
73
98
(15/16")
(15/16")
(33/8")
(11/2")
(15/16")
(21/16")
(23/16")
(31/8")
(39/16")
(19/16")
(133/4") (133/4")
(17/8")
(15/16")
(13/16")
(1/2")
(19/16")
(3/8")
(17/8")
(15/16")
(23/4")
(1/2")(3/8")
(315/16") (31/8")
(315/16")
(315/16"-393/8")
(23/4")
(23/4")
(51/2")
(19/16")
(1")(1/4")
(13/16")
(13/16")
(11/8")
(1/4")
(1/4") (11/8")
(13/16")
(1/16")
(37/8")
(27/8")
Husky
Flexirol Flexirol
112 113112 113
556/62/20
fl12
225
20 35
85
110
68
40
4022535
85
fl12
110
2323
556/63/40 556/62/40
5
221
458262
50
122
556 556/57 82
85
38
555 555/57 555/52
165
225
3881555/21
555/61
81
152
81
81
38
38
85
81
85
38
(27/16") (31/4")
(13/4")
(115/16")
(413/16") (11/2")
(33/8")
(31/4")
(31/4")
(31/4")
556/52
165
225
38
82
556/61
6
82
38
185
127
(87/8")
(5")
(11/2")
(3/16")
(61/2")
(75/16")
(1/4")
(11/2") (63/4")
556/21
81
81
82
152
38
5
44
172
(13/4")
(3/16")
(6")
(31/4")
(33/16")
(33/16")
(11/2")
(83/4")
556A/221
(33/16")
(11/2")
(33/16")
(33/16")
(6")
(11/2")
(33/8")
H A N G E R S
57B
25
561/2B56B 56BX
HENDERSON
90
62BA/148
61B61B/4
52B
HENDERSON
HENDERSON
HENDERSON
HENDERSON
HENDERSON
HENDERSON
HENDERSON
21B 21B/4 21B0/4
63BA/10463B0A/114 63BA/20562BA/250
205
12
90
fl10
148
12
250
909090
fl10
114
fl10
90
104
25
38 38
140
65
5
185
5
124
133
25
13
155
1325 25 13
(39/16")90
(29/16")65
(51/2")
(39/16")
(29/16")
(51/2")139
(1")
(75/16")185
(3/16")(75/16")
(3/16") (51/4")
(1")
(47/8")
(11/2")
(6")152
(61/8")
(11/2")
(6")
(61/8")
152
38
155
(11/2")
(6")
(61/8")
152
155
(1") (1/2") (1") (1/2") (1") (1/2")
(39/16")
(41/2")
(3/8") (3/8")
(3/8")
(39/16") (39/16") (39/16") (39/16")
(41/8")(513/16")
(913/16")
(1/2")
(1/2")
(81/16")
(1/2")
25.4
35
21B/MD
12.7
76
152.5
152.5
61B/MD
34.5
76
140
25
(3")
(13/8")
(51/2")
(1") (6")
(6")
(1")
(3")
(13/8")
57B
25
561/2B56B 56BX
HENDERSON
90
62BA/148
61B61B/4
52B
HENDERSON
HENDERSON
HENDERSON
HENDERSON
HENDERSON
HENDERSON
HENDERSON
21B 21B/4 21B0/4
63BA/10463B0A/114 63BA/20562BA/250
205
12
90
fl10
148
12
250
909090
fl10
114
fl10
90
104
25
38 38
140
65
5
185
5
124
133
25
13
155
1325 25 13
(39/16")90
(29/16")65
(51/2")
(39/16")
(29/16")
(51/2")139
(1")
(75/16")185
(3/16")(75/16")
(3/16") (51/4")
(1")
(47/8")
(11/2")
(6")152
(61/8")
(11/2")
(6")
(61/8")
152
38
155
(11/2")
(6")
(61/8")
152
155
(1") (1/2") (1") (1/2") (1") (1/2")
(39/16")
(41/2")
(3/8") (3/8")
(3/8")
(39/16") (39/16") (39/16") (39/16")
(41/8")(513/16")
(913/16")
(1/2")
(1/2")
(81/16")
(1/2")
25.4
35
21B/MD
12.7
76
152.5
152.5
61B/MD
34.5
76
140
25
(3")
(13/8")
(51/2")
(1") (6")
(6")
(1")
(3")
(13/8")
PACER MULTIDIRECTIONAL HANGERS
FLEXIROL HANGERS (135° movement)
PACER HANGERS
114 115114 115
fl 16
21K/PX(Top)
21B/P(Top)
(Bottom) (Bottom)
2513 13
13
38
13
45
38
13
45
(Bottom)
45
fl21
40
102
45
17.5
154
38
(Top)
7
45
19
152
178
7
152
38
Bolt M6
25
35
102
fl 21
25
40 102
fl 21
25
40
(61/8")155
(6")152
(11/2")
(61/8")
(6")
(11/2")
155
(1/2")
(1")(1/2")(1")(1/2")
(1/2") (1/2")
(61/8")
(11/2")
155(61/8")
(11/2")
(1") (1")
(19/16")
155
(4")
(13/16")
(13/4")
(4")
(13/16")(19/16")
(13/4")
(13/4") (61/16")
(4")
(19/16")
(13/4")(13/16")
(1/4")
(11/16")
(5/8")
(11/2")
(23/4")
(11/16")
(215/16")38
70
1874
(13/4")
(1/4")
(7")
(6")
(13/8")
(3/4")
P I VOT S E T S
H A N G E R S
FLEXIROL HANGERS (90° movement)
556/62/20
fl12
225
20 35
85
110
68
40
4022535
85
fl12
110
2323
556/63/40 556/62/40
5
221
458262
50
122
556 556/57 82
85
38
555 555/57 555/52
165
225
3881555/21
555/61
81
152
81
81
38
38
85
81
85
38
(27/16") (31/4")
(13/4")
(115/16")
(413/16") (11/2")
(33/8")
(31/4")
(31/4")
(31/4")
556/52
165
225
38
82
556/61
6
82
38
185
127
(87/8")
(5")
(11/2")
(3/16")
(61/2")
(75/16")
(1/4")
(11/2") (63/4")
556/21
81
81
82
152
38
5
44
172
(13/4")
(3/16")
(6")
(31/4")
(33/16")
(33/16")
(11/2")
(83/4")
556A/221
(33/16")
(11/2")
(33/16")
(33/16")
(6")
(11/2")
(33/8")
556/62/20
fl12
225
20 35
85
110
68
40
4022535
85
fl12
110
2323
556/63/40 556/62/40
5
221
458262
50
122
556 556/57 82
85
38
555 555/57 555/52
165
225
3881555/21
555/61
81
152
81
81
38
38
85
81
85
38
(27/16") (31/4")
(13/4")
(115/16")
(413/16") (11/2")
(33/8")
(31/4")
(31/4")
(31/4")
556/52
165
225
38
82
556/61
6
82
38
185
127
(87/8")
(5")
(11/2")
(3/16")
(61/2")
(75/16")
(1/4")
(11/2") (63/4")
556/21
81
81
82
152
38
5
44
172
(13/4")
(3/16")
(6")
(31/4")
(33/16")
(33/16")
(11/2")
(83/4")
556A/221
(33/16")
(11/2")
(33/16")
(33/16")
(6")
(11/2")
(33/8")
556/62/20
fl12
225
20 35
85
110
68
40
4022535
85
fl12
110
2323
556/63/40 556/62/40
5
221
458262
50
122
556 556/57 82
85
38
555 555/57 555/52
165
225
3881555/21
555/61
81
152
81
81
38
38
85
81
85
38
(27/16") (31/4")
(13/4")
(115/16")
(413/16") (11/2")
(33/8")
(31/4")
(31/4")
(31/4")
556/52
165
225
38
82
556/61
6
82
38
185
127
(87/8")
(5")
(11/2")
(3/16")
(61/2")
(75/16")
(1/4")
(11/2") (63/4")
556/21
81
81
82
152
38
5
44
172
(13/4")
(3/16")
(6")
(31/4")
(33/16")
(33/16")
(11/2")
(83/4")
556A/221
(33/16")
(11/2")
(33/16")
(33/16")
(6")
(11/2")
(33/8")
114 115114 115
fl 16
21K/PX(Top)
21B/P(Top)
(Bottom) (Bottom)
2513 13
13
38
13
45
38
13
45
(Bottom)
45
fl21
40
102
45
17.5
154
38
(Top)
7
45
19
152
178
7
152
38
Bolt M6
25
35
102
fl 21
25
40 102
fl 21
25
40
(61/8")155
(6")152
(11/2")
(61/8")
(6")
(11/2")
155
(1/2")
(1")(1/2")(1")(1/2")
(1/2") (1/2")
(61/8")
(11/2")
155(61/8")
(11/2")
(1") (1")
(19/16")
155
(4")
(13/16")
(13/4")
(4")
(13/16")(19/16")
(13/4")
(13/4") (61/16")
(4")
(19/16")
(13/4")(13/16")
(1/4")
(11/16")
(5/8")
(11/2")
(23/4")
(11/16")
(215/16")38
70
1874
(13/4")
(1/4")
(7")
(6")
(13/8")
(3/4")
P I VOT S E T S
fl16
fl10
67B/2012
70
20
40
67B/2012
70
40
20
47 68
40152
68B/2068BX/40
110
fl16
fl10
114
20
40
40
47 68
1325
102
155
38
13
89/2N 104N/94 104NX/94
21N/94
68B/2068BA/180
110
fl16
fl10
114
40
40
180
152
9
5448
25
35 80
16
32
23
58fl10
21R/94
133
106N/94
3
103
(57/8")150
(31/8")(13/8")
(3/8")
(5/8")
(1")
(21/8")(17/8")
(25/16") (3/8")
(11/4")
(7/8")
(3/8")
(51/4")
(7/8")
(11/4")32
23
(1")
(5/8")(41/16")
(1/8")
25
(11/2")
(61/8")
(1/2")
(4")
(1")
(1/2") (3/16")
(61/16")(4")
(13/4")
154
102
45
5
G U I D E S
21/550P
116 117116 117
HENDERSON
HENDERSON
201
55
fl32mm
9
90
55 55 46
46
101
38
25
42
4655
101
37
90
4655
101
(15/8") (11/2")
(1")
(113/16")(23/16")
(4")
(39/16")
(17/16")
(113/16")(23/16")
(4")
(23/16")
(4")
(3/8")
(113/16")
(11/4")
(39/16")
(23/16") (23/16")
(715/16")
(113/16")
G L A S S F I T T I N G S
EF07 EF03
EF01/4 EF01/2
67BA/150
20
fl10
110 40
(19/16")
(3/8")
(13/16")
(45/16")
68BA/110 68BA/180
110
fl16
180
12
70(23/4")
(45/16")
(5/8")
(71/8")
(1/2")
fl16
67BA/220
12
110
110
220
(45/16")
(5/8")
(1/2")
(811/16")
(45/16")
40
40
150(515/16")
(19/16")
(19/16")
G U I D E S
PACER ENDFOLD
67BA/150 67BA/220 68BA/110 68BA/180
116 117116 117
EF05 EF04
EF06
EF09Loose Bolt EF08
EF02
55 55
201
46
201
4655 55
55
fl16
4655
201
30
60
55
85
28
15
50
46
101
55
fl16
46
101
55
30
(23/16")
(715/16")
(23/16")
(113/16")(715/16")
(23/16") (23/16")
(113/16")
(715/16")
(23/16") (23/16")
(113/16")
(13/16")
(5/8")
(23/16")
(113/16")
(13/16")
(5/8")
(4")
(23/16")
(33/8")
(115/16")
(23/8")
(11/8")
(9/16")
(4")
(23/16")
(113/16")
G L A S S F I T T I N G S EF05 EF04
EF06 EF02
EF08Loose Bolt
✝ Standard hinge finishes: White (RAL 9010), Polished Anodized, Silver Anodized and Black Anodized.
For glass cutting dimensions contact Henderson.
88
41
F3734
HENDERSONHENDERSON
F3715 400333 454
HH3/30135
10
24
225
3
80
30
65
151
190
108
47
18
45
(87/8")
(3/8")
(515/16")
(5/16")
(15/16")
(13/8")
(71/2")
(15/8")
(5/16")
(41/4")
(17/8")
(11/16")
(31/8")
(13/16")
(1/8")
(1/4")
(11/8")
(13/4")
(13/8")
(13/4")
(29/16")
7
28
fl11
45
35
HH3/290
AC C E S S O R I E S A N D S TO P S
F3734 S7
HH3/301
F3715 333 454 400Pacer
Flexirol
HH3/290
EF09
118 119118 119
TRACK & CHANNEL
All tracks are in galvanized finish. Once installed they should be kept greased, to reduce wear and increase life. Any length of track is obtained by butting 2 pieces of track together and fixing a brack-et at the joint, and closed brackets at each end.
(ft) 280 290 301 301H 305 307
6 • • • • • •
8 • • • • • •
10 • • • • • •
12 • •
20 •
(ins) 280 290 301 301H 305 307
A 11/16 13/4 25/8 25/8 311/16 43/32
B 13/16 17/16 25/32 25/32 21/4 27/8C 18G 14G 14G 12G 12G 6G
(ins) 89 94 97 99A 1 3/4 11/2 11/2B 1 13/16 11/16 113/16C 12G 17G 12G 12G
118 119118 119
TRACK BRACKETS
All brackets are aluminum alloy die castings except where otherwise indicated.
Pressed steel brackets in painted finish.
Pressed steel brackets – galvanized.Fit closed brackets at track ends, or fit end-clips 1A/301 EC (for alloy brackets) or 1/301 EC (for steel brackets) in the case of all 301 track brackets. Jointing brackets are only required at track curve ends. Maximum brack-et spacing is every 3 ft.
Fig no. A B C D E Bolt
281 19/16 1/4 11/8 15/8 9/16 8G screw
1A/290 25/8 1/2 2 11/4 11/165/16
1/290/S 3 1/2 25/32 23/8 11/16 5/16
1A/301 313/16 3/4 27/8 21/4 13/8 1/21/301/S 315/16 5/8 27/8 23/8 115/32 1/21A/305 51/2 1 33/8 3 11/2 5/81/307/S 61/4 1 35/8 3 125/32 5/8
•
•
•
*
Fig no. A B C D E Bolt
9A/290 111/16 5/8 23/4 15/16 2 14G screw
9/301/S 29/16 15/32 415/16 11/2 31/2 18G screw
9A/305 35/16 11/2 65/16 25/16 51/8 1/29/307/S 35/16 2 71/4 22 3/32 51/2 5/8
*
*
Fig no. A B D E F Bolt
5/290 31/8 13/16 11/2 21/8 11/161/2
5/301 43/8 15/16 21/4 31/8 19/165/8
5/305 61/8 11/2 3 35/8 17/8 3/45/307/S 71/2 1 4 35/8 12 5/32 3/4*
Fig no. A B D E F Bolt
7/301/S 49/16 11/2 23/8 25/8 19/165/8*
Fig no. A B C D E Bolt
3A/290 27/32 - 31/4 11/4 21/2 5/16
3A/301 33/8 - 51/8 21/4 315/161/2
3/301/S 315/32 - 51/8 21/4 313/16 1/23A/305 43/4 - 65/8 3 415/16 5/83/307/S 67/32 - 71/4 31/2 51/2 5/8
*
*
Fig no. A B C D E Bolt
4A/290 25/8 - 17/8 3 23/8 5/164A/301 33/4 - 3 45/8 33/4 1/24A/305 53/8 - 31/4 71/2 51/8 5/84/307/S 61/4 - 35/8 71/2 51/2 5/8*
Fig no. A B C D E Bolt
4/301S 311/16 - 13/4 45/8 33/4 1/2*
Fig no. A B C D Bolt
4R/280S 113/16 2 13/8 13/8 3/84R/290/S 113/16 13/16 13/4 21/16 3/84R/301/S 29/16 21/4 29/16 31/16 1/24R/305/S 211/16 3 213/16 4 7/32 5/84R/307/S 213/16 3 39/16 4 9/32 3/4
•••••
Fig no. A B&E C D F Bolt
6/301 33/4 31/8 6 5 35/8 3/8*
Fig no. A B C D E F Bolt
8/301/S 37/8 5 7 45/8 25/8 35/8 1/2*
•*
120 121120 121
HANGERS /N = Nylon wheels /S = Steel wheelsNylon wheels are quieter and avoid the need to grease track to reduce wear. Hence their car-rying capacity is greater. For automatic doors halve the carrying capacity and use nylon wheels if possible.
DimensionsA B C D 0
37/16 11/4 11/8 17/16 13/32
55/8 23/4 111/16 27/32 5/8
55/8 23/4 111/16 27/32 5/8
63/8 23/4 111/16 3 5/8
87/16 33/8 21/4 37/16 13/16
DoorWeight
Capacity300 lbs.300 lbs.400 lbs.
600 lbs.800 lbs.
800 lbs.1000 lbs.
1500 lbs.
2500 lbs.4400 lbs.
Trackno.
290
301
301H
305
307
Hangerno.
56X/N56K/S
56K/S 20056A/S56A/N
56A/S56A/S
56C/S
56F/S56FJ/S
DimensionsA B C D E
37/16 33/4 21/4 17/16 11/2 17/8
55/8 7 3 27/32 13/4 21/4
55/8 7 3 27/32 13/4 21/4
63/8 7 3 3 13/4 21/4
87/16 15 21/2 37/16 23/4
DoorWeight
Capacity300 lbs.300 lbs.400 lbs.
600 lbs.800 lbs.
800 lbs.1000 lbs.
1500 lbs.
4400 lbs.
Trackno.
290
301
301H
305307
Hangerno.
53K/N53K/S
53K/S 20053A/S53A/N
53A/S53A/N
53C/S
53FJ/S
-
-
-
-
DimensionsA B C D
71/16 21/4 111/16 17/1671/16 21/4 111/16 27/32
211/2 31/4 2 3
Trackno.290301
301H305
Hangerno.
62K
62A
62C
DimensionsA B C D E
6 6 1 17/16 3/16
7 6 11/2 27/32 1/4
7 6 11/2 3 1/4
Trackno.
290
301301H305
Hangerno.
21K/S21K/N21K/4N21A/S21A/4S
21C/S
DimensionsA B C D 0
37/16 43/8 11/8 17/16 13/32
55/8 511/16 111/16 27/32 5/8
55/8 511/16 111/16 27/32 5/8
63/8 511/16 111/16 3 5/8
87/16 51/2 21/4 37/16 13/16
DoorWeight
Capacity300 lbs.400 lbs.
600 lbs.800 lbs.
800 lbs.1000 lbs.
1500 lbs.
2500 lbs.4400 lbs.
Trackno.
290
301
301H
305
307
Hangerno.
56KX/S56KX/N56AX/S56AX/N
56AX/S56AX/N
56CX/S
56FX/S56FJX/S
DimensionsA C D E F
37/16 1 51/2 1/16 1
55/8 23/8 75/161/16 11/2
55/8 23/8 75/161/16 11/2
63/8 21/2 75/161/16 11/2
Trackno.
290
301
301H
305
Hangerno.
57K/N
57A/S
57A/N
57C/S
DoorWeight
Capacity
300 lbs.
600 lbs.
1000 lbs.
1500 lbs.
DimensionsA C D1 D2 E F
37/16 1 3 2 51/4 1
55/8 23/8 4 5 61/2 11/255/8 23/8 4 5 61/2 11/263/8 21/2 4 61/2 11/2
Trackno.
290
301
301H
305
Hangerno.
52K/S52K/N
52A/S
52A/N
52C/S
DoorWeight
Capacity300 lbs.300 lbs.
600 lbs.
1000 lbs.
1500 lbs.
DimensionsA B C D4 21/4 111/16 17/164 21/4 111/16 27/32
87/8 31/4 2 3
Trackno.290301
301H305
Hangerno.
63K
63A
63C
DimensionsA B C D51/2 3/16 1 17/1671/4 1/4 11/2 27/32
71/4 1/4 11/2 3
Trackno.
290301
301H305
Hangerno.
61K/S
61A/S
61C/S
120 121120 121
GUIDES OTHERS
No. 31S Single Wall Mounted Stay Roller (Bi-parting doors) - Provides clear threshold - fit No. 128 shoe guide with center stop. Nylon Rollers, galv. steel angle.
No. 31D Double Wall Mounted Stay Roller (Double line) - Provides clear threshold - Nylon Rollers, galv. steel angle.
No. 126HD/A Ground Stay Rollers - Provides clear threshold - Nylon Rollers, covered by shields to prevent traffic damage. Galv. steel.No. 128 Shoe Guide with Center Stop Grey painted iron, adjustable. Center stop plate provided, for bi-parting doors.
No. 299 Curtailed Rail with Inverted No. 89 Channel to underside of doors. - Provides clear threshold - fit No. 128 shoe guide with center stop on bi-parting doors.
No. 126 Ground Stay Rollers - Provides clear threshold - fit No. 128 shoe guide with center stop on bi-parting doors. Galv. steel.
Most roller guides are fitted with brass rollers. The assemblies are rustproofed by electrozinc galvanizing. Fit two guides per door. Always specify channel type when ordering guides (eg 104P/97).
No. 1021/2 Side Guide Roller (Patented) Heavy duty plough guide, ideal for most applications. Malleable body with self-adjusting roller spindles. Use with channel No. 97.
No. 105R Roller Guide - General purpose guide suitable for most applications. Is economical yet very strong. Use with channel Nos. 89 or 97.
No. 106R Under Guide Roller - Steel plate with a brass roller. Ideal for small, light doors especially internal application. Not recommended for dirty conditions. Use with channel Nos. 89, 94, or 97.
No. 113R Side Guide Roller - Steel plate with a brass roller. Not recommended for heavy doors or dirty conditions. Use with channel Nos. 89 or 94.
No. 104P Under Guide Roller (Patented) - Brass roller used for metal doors. Easily removable without dismounting doors. Use with channel Nos. 89 or 97.
No. 104PX Long Under Guide Roller - Same as 104P but with extra long bolt.
No. 67 Intermediate Guide - folding doors No. 67/89 for track 290 and channel 89.No. 67/97 for track 301 or 301H and channel 97.No. 67C/97 for track 305 and channel 97.
No. 68 End Guide - folding doors No. 68/89 for track 290 and channel 89.No. 68/97 for track 301 or 301H and channel 97.No. 68C/97 for track 305 and channel 97.
No. 21R End Fold Guide - folding doors No. 21KR/94 for track 290 and channel 94.No. 21R/94 for track 301, 301H and 305.
No. 106R Center Fold Guide - folding doors No. 106R/94 for all tracks.
No. 994 Cane Bolt - No. 994 15" electro galvanized steel shoot with socket for concrete, when required.
No. 994X Offset Cane Bolt - No. 994X 15" electro galvanized steel shoot with socket for concrete.
No. 994R Roller Guide Cane Bolt - No. 994R electro galvanized steel shoot with brass roller. Use with channel Nos. 89 or 97.
No. 994S Locking Cane Bolt - No. 994S 15" electro galvanized steel shoot with socket for concrete. Use with padlock (Not by PCH).
No. 77 Flush Bolt - No. 77J suitable for framed doors with bottom rails up to 6" x 17/8 ". Gray painted steel.No. 77S suitable for framed doors with bottom rails up to 9" x 23/4 ". Gray painted steel.
No. 78 Flush Bolt - Designed for fitting to stile of flush doors minimum 5" x 13/4 ". Gray painted steel.
No. 333 Semi-Flush Bolt - 6" x 13/8 " aluminum alloy in satin anodized finish. No. 454 Semi-Flush Bolt - 71/2" x 19/16 " aluminum alloy in satin anodized finish.
No. 863 Bow Handle - Gray painted iron. 51/4" x 13/4 "
No. 463 Bow Handle - Gray painted iron. 61/4" x 17/8 "
No. 464 Bow Handle - Gray painted iron. 101/4" x 21/4 "
No. 400 Flush Pull - Aluminum alloy in satin anodized finish. 41/4" x 17/8" with 5/8" mortise.
No. 414 Flush Pull - Aluminum self finish. 51/4" x 21/2" with 3/4" mortise.
No. 413 Flush Pull - Heavy duty Gray painted iron. 6" x 33/4" with 1" mortise.
No. 115 Corner Protection Plates - Rustproofed by electrozinc plating - Fit a pair on the leading door edge.
No. 109 Single Wall or Ground Stop - Gray painted steel with rubber buffer. For light doors. Fit on wall, 2/3 up door height.
No. 107E Buffer Stop - Rubber. For fitting to slamming post when other stops cannot be used.
No. 107 Single Wall Stop - Gray painted steel with rubber buffers. For medium weight doors, fit one on wall, 2/3 up door height. For heavier door fit 2.
No. 431 Swivel Locking Bar - Rustproofed by zinc plating. For doors sliding on outside face of wall or for securing to end post. Use with padlock (Not by PCH).
No. 430 Detachable Locking Bar - Rustproofed by zinc plating. For Straight-Run doors sliding inside and locked outside. Use with padlock (Not by PCH).
No. 65 Back Flap Hinges - No. 65 for track 290, 301 or 301H. Aluminum. No. 65C track 305. Gray painted iron.
No. 403 Butt Hinge - No. 403/1 31/2" x 2" aluminum alloy.No. 403/2 4" x 21/8" aluminum alloy.No. 403/3 4" x 3" aluminum alloy.
Also available in steel to similar sizes and referred to as No. 37, No. 41, No. 42 respectively.