OWNERS MANUALdl.owneriq.net/7/7a067e8c-5732-4c77-8d1d-237c40ae5f0e.pdfPrecision Comfort Owners Manual 7 MATTRESS RETAINER INSTALLATION 1.Before discarding any packing materials, check

99300642-b 1/06EDR10611

Serial No.

OWNERS MANUAL

www.lpadjustablebeds.com

CONTENTS

Advisory ............................................................................................................... 4

Acoustics .............................................................................................................. 6

Installation ............................................................................................................ 7

Sleep Number® Mattress Installation ............................................................... 13

Hand Control Operation .................................................................................... 16

Receiver Unit Operation .................................................................................... 17

Programming ..................................................................................................... 18

Accessories ........................................................................................................ 23

Troubleshooting ................................................................................................. 24

1-2-20 Warranty ................................................................................................. 25

© Leggett & Platt, Inc.

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

4

ADVISORY

ELECTRICAL GROUNDINGThis product is equipped with a polarized,grounded electrical power cord. Thepower cord will only fit into a grounded,electrical surge protection device (notincluded) or a grounded electrical outlet.

READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCTThis Precision Comfort™ adjustable foundation has been quality engineered with designfeatures to assure comfort and safety when operated properly.

WARRANTY WARNINGDo not open any control boxes, motors orhand control devices (with the exceptionof the hand control and power down boxbattery compartments). The productwarranty will be void if these componentsare tampered with. Do not attempt to altercomponent wiring or adjust or modify thestructure of the product in any way or thewarranty will be void. Any repair orreplacement of adjustable bed parts mustbe performed by authorized personnel.

LUBRICATIONThis product is designed to bemaintenance free. The lift motors arepermanently lubricated and sealed—noadditional lubrication is required. Do notapply lubricant to lift motor lead screws orany nylon nuts or the bed mayinadvertently creep downward from theelevated position.

PRODUCT RATINGSThe bed lift motors are not designed forcontinuous use. Reliable operation and fulllife expectancy will be realized as long asthe lift motors do not operate any morethan five (5) minutes over a thirty (30)minute period, or approximately 15% dutycycle. Note: massage equipped beds arenot designed for continuous, extendedmassage operation. Massage systems arerated for a maximum of 2 hours of usewithin any 6 hour period. Any attempt tocircumvent or exceed product ratings willshorten the life expectancy of the productand may void the warranty.

The recommended weight restrictions forPrecision Comfort™ adjustablefoundations are as follows: Twin-300 lbs(136.07kg), Full-375 lbs (170.09kg) andQueen-425 lbs (192.77kg). The bed willstructurally support the recommendedweights distributed evenly across thehead and foot sections. This product is notdesigned to support or lift this amountonly in the head or foot sections alone.Note: Exceeding the recommendedweight restrictions could damage youradjustable bed and void your warranty.

For best performance, consumers shouldenter and exit the adjustable bed with thebed in the flat (horizontal) position. DONOT SIT ON THE HEAD OR FOOT SECTIONS

WHILE IN THE RAISED POSITION.

IMPORTANT INFORMATION

FOR OPTIMUM ADJUSTABLE BEDOPERATION, USE A GROUNDED,

ELECTRICAL SURGE PROTECTIONDEVICE (NOT INCLUDED). FAILURE TOUSE A SURGE PROTECTION DEVICECOULD COMPROMISE SAFETY ORCAUSE PRODUCT MALFUNCTION.

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

5

LOCKING CASTERDETAIL

LO

CK

ADVISORY

READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCTThis Precision Comfort™ adjustable foundation has been quality engineered with designfeatures to assure comfort and safety when operated properly.

IMPORTANT INFORMATION

SMALL CHILDREN / PETS WARNINGAfter the foundation is unboxed,immediately dispose of packagingmaterial as it can smother small childrenand pets. To avoid injury, children or petsshould not be allowed to play under or onthe bed. Children should not operate thisbed without adult supervision.

HOSPITAL USE DISCLAIMERThis foundation is designed for in-homeuse only. It is not approved for hospitaluse and does not comply with hospitalstandards. Do not use this bed with tenttype oxygen therapy equipment, or usenear explosive gases.

PACEMAKER WARNINGThis product produces a vibratingsensation. It is possible that individualswith heart-assist pacemakers mayexperience a sensation similar to exercise.Consult physician for completeinformation.

SERVICE REQUIREMENTSService technicians are not responsible formoving furniture, removing headboardsand footboards or any items required toperform maintenance on your adjustablefoundation. In the event the technician isunable to perform service due to lack ofaccessibility, the service call will be billedto the purchaser and the service will haveto be rescheduled.

FCC COMPLIANCEPrecision Comfort™ electrical componentsare rated for 110/120 voltage, 60Hz, 3.9amp. Components meet Class B digitaldevice rating (Part 15, FCC rules) forresidential use. Precision Comfort™adjustable foundations generate, use andmay radiate radio frequency energy. Radiocommunication may be affected if notinstalled and operated as recommendedin this manual.

LOCKING CASTER SAFETY FEATURE(If applicable)The Precision Comfort™ foundation isequipped with locking casters to prohibitthe bed from movement. For best results,place rubber caster cups under lockingcasters when the bed is located onsmooth or hard surface flooring—it ispossible for locking caster equipped bedsto slide without the use of rubber castercups.

To activate locking casters, push down onthe lock tab. To disengage the lockingmechanism, lift up the lock tab (seeillustration below).

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

6

ACOUSTICS

LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimalhumming sound during operation. This isnormal.

During Precision Comfort™ operation, thelift arm wheels make contact with theplatform support of the bed. This appliesslight tension on the moving componentsand resonance is reduced to a minimumlevel. If excessive noise or vibration isexperienced, reverse the movementaction (up or down) of the bed with thehand control. This should realign the bed’sactivating mechanisms to the properoperational position.

MASSAGE OPERATIONThe massage feature will emit a minimaltone during operation. This is normal.When the massage level is increased,motor resonance will intensifyaccordingly.

LOCATION ENVIRONMENTThe level of sound experienced duringPrecision Comfort™ operation is directlyrelated to the location environment. Forexample, when a bed is located on ahardwood floor with the massage featurein operation, a vibrating tone will beaudible. To minimize this resonance, placea piece of carpet—or optional rubbercaster cups—under each leg or caster ofthe bed. See the accessory sheet includedwith this product for rubber caster cuporder information.

It is possible to experience vibration ornoise from the headboard brackets,headboards or footboards if mountingbolts are not firmly tightened.

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

7

MATTRESSRETAINER

INSTALLATION

1. Before discarding any packing materials,check the adjustable bed shipping cartonand verify the following items areincluded:

• (1) Mattress Retainer

• (1) Mattress Retainer Hardware Kit

• (4) Bed Legs

• (4) Locking Leg Casters

• (2) Headboard Bracket Assemblies

• (1) Headboard Bracket Hardware Kit

• (1) Precision Comfort® FoundationHardware Kit (not shown)

• (1) Hand Control

• (1) Owners Manual

• (1) Registration Card

For Precision Comfort™ installation and setup, complete the numbered procedureindicated below and on the following pages:

LOCKING LEG CASTER(4 pieces)

HEADBOARD BRACKETHARDWARE KIT(hardware: 16 pieces)

LEG (4 pieces)

MATTRESS RETAINERHARDWARE KIT(hardware: 16 pieces)

ANGLE BRACE

HEADBOARD BRACKET ASSEMBLIESQueen size shown—twin size (or smaller)headboard brackets are notequipped with angle brace.

HAND CONTROL

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

8

INSTALLATION

6. Remove the plastic packaging from thebed base frame. Carefully rotate the baseframe over to position the bed top-side-up.

7. Plug power cord into a working, groundedelectrical outlet. Note: an electrical surgeprotection device is recommended (notincluded).

8. Install batteries in hand control. Brieflyactivate all functions of the bed with thehand control to verify all features are inworking order. If foundation does notoperate, refer to the Troubleshootingsection of this manual.

9. Return foundation to the level position.

2. Carefully Lift the bed base frame from theshipping carton, keeping the unit top-side-down.

3. Install (4) legs into the base frame. Simplyscrew each leg into a tapped hole at eachcorner of the base frame (FIGURE 1). Insertcasters into the bottom of each bed leg (ifapplicable).

4. Remove and extend out power cord fromthe protective packaging.

5. Install (2) 9 volt batteries into the receiverunit (FIGURES 2 and 3). The DC receiverunit is commonly referred to as a powerdown box.

FIGURE 1: Precision Comfort™ leg installation. Casterinstallation (if applicable).

LEGS – SCREW INTOTAPPED HOLE ATEACH CORNER

CASTERS – PRESS-FITINTO BOTTOM OFLEGS (IF APPLICABLE)

POWER CORDS MUST NOT INTERFEREWITH ANY ADJUSTABLE BED

MECHANISMS.

FIGURE 2: Receiver unit (power down box) batterycompartment door removal.

PRESS IN (SLIGHTLY) ANDPUSH DOWN TO REMOVEBATTERY COMPARTMENTDOOR

POWER DOWN BOXBATTERY COMPARTMENT DOOR

BATTERY ORIENTATION ISINDICATED INSIDE BATTERYCOMPARTMENT

DOOR REINSTALLATION:PRESS COMPARTMENT DOORAGAINST THE BATTERY ENDS,SLIDE DOOR UP AND INTO ENGAGE THE DOOR TABS

TABS

FIGURE 3: Power down box battery installation and batterycompartment door reinstallation.

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

9

INSTALLATION

10. Install mattress retainer as follows:

a. Locate (1) mattress retainer and (1)mattress retainer hardware kit (bag).

b. Install (1) cupped washer, (1) spacerand (1) flat washer on (4) mattressretainer bolts (FIGURE 4).

c. Locate (4) threaded lugs in the top sideof the foot section of the foundationbase. The lugs will be marked withlocating pins.

d. Remove the locating pins (pull out).

e. Install the mattress retainer bolts (loosely)into the (4) threaded lugs (FIGURE 5).

f. Slide each U-shaped end of themattress retainer around the mattressretainer bolts. Position the retainerends between the spacer and thewasher (FIGURE 5).

MATTRESS RETAINER HARDWARE

KIT CONTAINS:

(4) MATTRESS RETAINER BOLTS - A

(4) FLAT WASHERS - B

(4) SPACERS - C

(4) CUPPED WASHERS - D

CUPPEDWASHER

FLATWASHER

SPACER

MATTRESSRETAINERBOLT

ASSEMBLE ASSHOWN BELOW:

A

B

C

D

FIGURE 4: Mattress retainer hardware.

g. Tighten screws to complete mattressretainer installation (FIGURE 6).

Note: if adjustable foundation is to be setup without a headboard, install mattresson the foundation base frame andinstallation is complete. If headboard isto be installed, proceed to step 11.

DO NOT USE POWER SCREWDRIVER TOINSTALL MATTRESS RETAINER. DO NODO NODO NODO NODO NOTTTTTOOOOOVERTIGHTEN MAVERTIGHTEN MAVERTIGHTEN MAVERTIGHTEN MAVERTIGHTEN MATTRESS RETTTRESS RETTTRESS RETTTRESS RETTTRESS RETAINERAINERAINERAINERAINERHARDHARDHARDHARDHARDWWWWWARE!ARE!ARE!ARE!ARE!

NOTE

FIGURE 6: Typical mattress retainer installed.

FLAT WASHERS FIT BETWEENTHE FOUNDATION BASE FRAMEAND THE MATTRESS RETAINER

(2) THREADED LUGS INEACH SIDE OF THE

FOUNDATION FOOTSECTION (MARKED WITH

LOCATING PINS)

MATTRESSRETAINER

FIGURE 5: Mattress retainer installation.

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

10

INSTALLATION

FAILURE TO FOLLOW HEADBOARDBRACKET INSTALLATION INSTRUCTIONSMAY CAUSE HEADBOARD BRACKETINTERFERENCE WITH BASE FOAM DURINGADJUSTABLE BED OPERATION. BASEFOAM OR BASE COVER DAMAGE COULDRESULT.

NOTE

11. Install headboard brackets to thefoundation base frame. When attaching (2)twin size units to a king size headboard,use swing-away hinges (see accessories)to connect the twin units.

3 inches M

AX.

FIGURE 7: headboard cross member location must notexceed 3 inches (76.2mm) from the top of the mattress.

12. Install headboard bracket assemblies perthe following procedure:

a. Raise the head section of the bed (withhand control) to gain access to the bedbase frame.

b. Slide one headboard bracket channelonto one side of the bed base frame.Using (2) bolts/nuts (FIGURE 8) attachchannel to base frame (FIGURE 9).Hand tighten bolts/nuts (loosely) toallow adjustment of the headboardbracket channels. Repeat procedure toinstall the other headboard bracketchannel to the other side.

FIGURE 8: Headboard bracket hardware.

HEADBOARD BRACKETHARDWARE KIT CONTAINS:

(4) 3 INCH CARRIAGE BOLTS - A(4) 1 INCH HEX HEAD BOLTS - B(8) NUTS - C

CA

B

IN ORDER TO AVOID A PERSON OR PETBEING CAUGHT IN THE SPACEREFERENCED BELOW WHILE THE BED IS INMOTION, THE BOTTOM OF THEHEADBOARD CROSS MEMBER MUST BEPOSITIONED SO THAT THERE IS NO MORETHAN 3 INCHES (76.2mm) BETWEEN THEHEADBOARD AND THE TOP OF THEMATTRESS (FIGURE 7). DO NODO NODO NODO NODO NOT EXT EXT EXT EXT EXCEEDCEEDCEEDCEEDCEED3 INCHES (76.23 INCHES (76.23 INCHES (76.23 INCHES (76.23 INCHES (76.2mmmmmmmmmm).).).).). FAILURE TO FOLLOWTHIS INSTRUCTION COULD RESULT INSERIOUS PERSONAL INJURY OR DEATH.

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

11

INSTALLATION

c. Attach one headboard bracket flangeto one of the bracket channels with (2)bolts/nuts. (FIGURE 10) Tighten bolts.Repeat procedure to attach the otherheadboard bracket flange.

FIGURE 10: Headboard bracket flange installation (attach oneflange to each of the headboard bracket channels).

USE (2) 1 INCH BOLTS ANDNUTS (TIGHTEN) TO ATTACHHEADBOARD BRACKET FLANGETO EACH BRACKET CHANNEL

ANGLEBRACE

QUEEN SIZE HEADBOARD BRACKETASSEMBLIES ARE SHOWN. TWIN SIZEHEADBOARD BRACKETS (OR SMALLER)ARE NOT EQUIPPED WITH ANGLE BRACE(FIGURES 9 and 10).

NOTE

FIGURE 9: Headboard bracket channel installation (one eachside of the head section of the bed).

SLIDE HEADBOARDBRACKET CHANNEL OVERTHE FRAME EXTENSION

USE (2) 3 INCH CARRIAGE BOLTS ANDNUTS TO ATTACH EACH BRACKETCHANNEL TO THE FRAME EXTENSIONS

ANGLEBRACE

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

12

d. Slide headboard bracket assemblies (inor out) to achieve a distance of 1.5inches (38.1mm) to 2 inches (50.8mm)between the edge of the foundationbase and headboard bracket flangeassemblies (FIGURE 11).

e. Firmly tighten the 3 inch carriage boltsof both headboard bracket channels.

f. Measure the distance (center-to-center) between the mounting holes inthe headboard.

g. Measure the center-to-center distancebetween the mounting slots of theheadboard bracket flanges (FIGURE 12).

h. If bracket flange adjustment is requiredto accept the headboard, remove the 1inch headboard bracket flange boltsand moveflanges side-to-side for theadjustment(FIGURE 12).Reinstall boltsand tighten.

i. Installheadboard.

13. Install mattress onthe foundation.

Typical PrecisionComfort™ installationis now complete.

INSTALLATION

FIGURE 12: Headboard bracket measurement and adjustment to accept headboard.

MEASURE FLANGE SLOTS

CENTER-TO-CENTER TO CHECK

HEADBOARD HOLE LOCATION

REMOVE 1 INCH BOLTS AND RELOCATEFLANGES TO ACHIEVE CENTER-TO-CENTER DISTANCE REQUIRED FOR

HEADBOARD MOUNTING HOLES

FIGURE 11: Headboard bracket position from the edge of thefoundation base frame.

1.5 to 2 inches

SLIDE BRACKET

ASSEMBLIES IN OR

OUT TO ACHIEVE

POSITION

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

13

Sleep Number® MATTRESS INSTALLATION

IMPORTANT: Wash hands beforebeginning installation. Residue onhands will easily transfer to clothcovered bedding components.

A

B

“A” = 32-1/2” (approx.)“B” = 6” (approx.)

FIGURE 13

APPROXIMATELOCATOR PINPOSITION

FIGURE 14: Locator pin removal.

PULL OUT EACH PIN FROMTHE THREADED LUGS.

INSTALLATION INSTRUCTIONSTools required—utility knife, Phillips® head screwdriver.

Install the Sleep Number® mattress, perthe following procedure:

1. Verify Precision Comfort® adjustablefoundation setup is complete.

2. Identify and remove (2) locator pins in theadjustable foundation (FIGURES 13 and14). Note: approximate locator pinposition is 32-1/2” from the top and 6”from the side of the adjustablefoundation. Locator pins mark threadedlug location used for Sleep Number®

mattress attachment.

3. Unzip the top panel of theSleep Number® mattresscover and set the panelaside.

4. Position the bottom of theSleep Number® mattress on topof the adjustable foundation.

5. Insert foam border walls andcorner locks into the mattress cover perthe Sleep Number® mattress installationinstructions.

6. Align the Sleep Number® mattress coverflush against the adjustable foundationmattress retainer bar (at the foot end of thebed). Align the top and side edges of themattress cover flush with the adjustablefoundation so the mattress cover and thefoundation are a matched pair.

7. Locate the 2 threaded lug mountinglocations (with fingers).

EXACT SIDE AND END ALIGNMENT OF THESLEEP NUMBER® MATTRESS COVERASSEMBLY WITH THE ADJUSTABLEFOUNDATION MUST BE ACHIEVED BEFOREPROCEEDING TO STEP 8.

NOTE

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

14


EXERCISE EXTREME CAEXERCISE EXTREME CAEXERCISE EXTREME CAEXERCISE EXTREME CAEXERCISE EXTREME CAUTION WHENUTION WHENUTION WHENUTION WHENUTION WHENUSING UTILITY KNIFE!USING UTILITY KNIFE!USING UTILITY KNIFE!USING UTILITY KNIFE!USING UTILITY KNIFE! THE DANGER OFSERIOUS FINGER CUTS ARE POSSIBLE IFUTILITY KNIFE IS NOT USED CORRECTLY.

8. At each threaded lug location, make asmall cut (no larger than 1/4” long) throughthe mattress cover fabric with a utility knife(FIGURE 15).

9. Position a large plastic washer over eachcut in the mattress cover fabric (FIGURE15).

10. Position a metal washer over each plasticwasher (FIGURE 15).

11. Insert one of the mounting bolts throughboth washers and screw into one of themounting lugs. Snug fit...Do notovertighten!

12. Insert the other mounting bolt per Step 11.

13. Complete mattress setup per the SleepNumber® installation instructions. This willinclude fitting the base pad, air chambers,center wall and topper pad.

14. Position and zip the top panel to the SleepNumber® mattress cover to completeinstallation.

SLEEP NUMBER® MATTRESS HARDWAREAND COMPONENTS VARY PER MODEL.

NOTE

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

15


IF ADJUSTABLE FOUNDATION SERVICE ISREQUIRED, REMOVE THE SLEEP NUMBERÆ

MATTRESS BEFORE THE SERVICETECHNICIAN ARRIVES.

NOTE

SLEEP NUMBER®

MATTRESS COVEREQUIPPED WITH

ZIPPERED TOP PANEL

MOUNTINGBOLTS

METALWASHERS

LARGEPLASTICWASHERS

FOAM WALLSECTIONS

LOCATOR PINS(THREADED LUGLOCATION)

ADJUSTABLEFOUNDATION

FIGURE 15

IMPORTANT: makecertain all 4 sides of theSleep Number® mattresscover are flush alignedwith the adjustablefoundation before cuttingsmall slit (no larger than1/4” long) in the bottompanel of the mattresscover.

CORNERLOCK (4)

FOAM WALLCENTER SECTION

MATTRESS RETAINER BAR(FOOT END OF BED)

CUT 1/4 INCH SLITTHROUGH BOTTOMFABRIC PANEL OFMATTRESS COVER

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

16

HAND CONTROL OPERATION

HAND CONTROL REQUIRES FOUR (4) AAA SIZE BATTERIES. TO CONSERVEBATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANYBUTTON IS PRESSED FOR MORE THAN 50 SECONDS.

NOTE

TRANSMISSIONINDICATOR LIGHT

MASSAGE SET BUTTONPress to capture a setting of themassage and/or wave functions

as a programmed position. Pressthe favorite massage button to

activate the preset position.

POSITION RECALL BUTTONSPress to recall a massage/wavesetting assigned by the programset button.

FOOT UP/DOWN BUTTONPress and hold to raise orlower the foot section.

HEAD UP/DOWN BUTTONPress and hold to raise or lower

the head section.

HEAD MASSAGE BUTTONSPress and hold to increase or

decrease head massage intensity.

HEAD MASSAGE ON/OFF BUTTONSwitches head massage on or off.

When switched on, the massagefunction will automatically shut off

after 30 minutes.

FOOT MASSAGE ON/OFF BUTTONSwitches foot massage on or off.When switched on, the massagefunction will automatically shut offafter 30 minutes.

FOOT MASSAGE BUTTONSPress and hold to increase ordecrease foot massage intensity.

FLAT BUTTONPress to return bed to thelevel position.

FAVORITE MASSAGE BUTTONPress to recall a massage and/orwave function set by the massageset button.

WAVE SPEED BUTTONSPress and hold—after the head

and foot massagers, and thewave system have been

activated—to increase ordecrease the wave speed.

WAVE ON/OFF BUTTONPress to activate or deactivatethe wave vibration system.

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

17

RECEIVER UNIT OPERATION

In case of a power outage, press and holdthe learn button on the receiver unit(power down box) to lower the bed to theflat position (FIGURE 18).

This function is only for lowering the bedand will not operate the bed to any otherposition. The (2) 9 volt batteries should bereplaced after this function is used.

In the event the power down feature doesnot work, check to make sure the (2) 9 voltbatteries are good.

LEARNBUTTON

FIGURE 16: Power down box learn button.

POWERDOWN BOX

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

18

The two step procedure below is required to program 1 hand control to operate 1 bed.Before beginning, make certain the bed is plugged into a working grounded electricaloutlet.

STEP 1Locate the receiver unit (power down box)for the bed and press the learn buttonfor 1 second and release (FIGURE 16).

STEP 2On the hand control, simultaneously pressand hold the POS 1 and head massage on/off buttons (FIGURE 17). The transmissionindicator light will flash slowly and thenflash rapidly. Continue to hold for 5seconds and then release the buttons.

One hand control is now programmed tooperate one bed.

IF PROGRAMMING FAILS, INITIATE THEPROGRAMMING PROCEDURE A SECONDTIME.

NOTE

PROGRAMMING 1 hand control - 1 bed

LEARNBUTTON


POWERDOWN BOX

POS 1BUTTON


FIGURE 17

HEAD MASSAGEON/OFF BUTTON

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

19

PROGRAMMING 2 hand controls - 1 bed

The three step procedure below is required to program 2 hand controls to operate 1 bed.Before beginning, make certain the bed is plugged into a working grounded electricaloutlet.

STEP 1Locate the power down box for the bedand press the learn button for 1 secondand release (FIGURE 16).

STEP 2On hand control 1, simultaneously pressand hold the POS 1 and the head massageon/off buttons (FIGURE 17). Thetransmission indicator light will flashslowly and then flash rapidly. Continue tohold for 5 seconds and then release thebuttons.

STEP 3Repeat Step 1 and Step 2 with handcontrol 2.

Two hand controls are now programmedto operate one bed.

HANDCONTROL 1

HANDCONTROL 2


NOTE

LEARNBUTTON


POWERDOWN BOX

POS 1BUTTON


FIGURE 17


Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

20


NOTE

The three step procedure below is required to program 1 hand control to operate 2 beds.Before beginning, make certain the beds are plugged into a working grounded electricaloutlet.

STEP 1Locate the power down box for bed 1 andpress the learn button for 1 second andrelease (FIGURE 16).

STEP 2On the hand control, simultaneously pressand hold the POS 1 and the head massageon/off buttons (FIGURE 17). Thetransmission indicator light will flashslowly and then flash rapidly. Continue tohold for 5 seconds and then release thebuttons.

STEP 3Repeat Step 1 and Step 2 with bed 2

One hand control is now programmed tooperate two beds.

BED 1

BED 2

PROGRAMMING 1 hand control - 2 beds

LEARNBUTTON


POWERDOWN BOX

POS 1BUTTON


FIGURE 17


Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

21

STEP 6Repeat Step 4 and Step 5 with hand control 2.

Two hand controls are now programmed tooperate two beds.


STEP 2On hand control 1, simultaneously press andhold the POS 1 and the head massage on/offbuttons (FIGURE 17). The transmissionindicator light will flash slowly and then flashrapidly. Continue to hold for 5 seconds andthen release the buttons.


STEP 4Locate the power down box for bed 2 andpress the learn button for 1 second andrelease. (FIGURE 16).


The six step procedure below is required to program 2 hand controls to operate 2 beds.Before beginning, make certain the beds are plugged into a working grounded electricaloutlet.

PROGRAMMING 2 hand controls - 2 beds

HAND CONTROL 1 BED 1


LEARNBUTTON


POWERDOWN BOX


NOTE

POS 1BUTTON


FIGURE 17


Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

22

PROGRAMMING separating 2 beds

The six step procedure below is required to separate 2 hand controls from operating 2 beds.One hand control per bed operation will result. Before beginning, make certain the beds areplugged into a working grounded electrical outlet.



STEP 3Repeat Step 1 and Step 2 with hand control 1.Note: wait 90 seconds before proceeding toStep 4.

STEP 4Locate the power down box for bed 2 andpress the learn button for 1 second andrelease. The bed will be equipped witheither a power down box or J box (FIGURE

16).



Independent hand control operation is nowrestored (hand control 1 operating bed 1;hand control 2 operating bed 2).




NOTE

LEARNBUTTON


POWERDOWN BOX

POS 1BUTTON


FIGURE 17


Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

23

ACCESSORIES

Precision Comfort™ OPTIONAL EQUIPMENTContact your nearest Select Comfort® retail dealer or call toll free at 800-582-7216 foraccessory pricing and to order the accessories indicated in the chart below:

107397

107396

107398

1 Headboard brackets cannot be used with glides.

ACCESSORY DESCRIPTION

Glides1 (set of 4, replaces legs) 107397

7” Legs (set of 4) 107399

Swing-away Hinges 107396

Bed Straps (connects 2 Precision Comfort® foundations together) 107398

CODE

107399

7”

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

24

TROUBLESHOOTING

In the event the Precision Comfort™ adjustable bed fails to operate, investigate thesymptoms and possible solutions provided in the chart below:

SYMPTOM

• Verify power cord is plugged into a working,

grounded electrical outlet. A grounded,

electrical surge protection device is recommended.

Test outlet by plugging in another working appliance.

• Program the hand control (see Programming, for

procedures). If equipped with power down box, make

certain power down box is easily accessible. Relocate

power down box if required.

• Unplug power cord, wait 45 seconds and plug in to

reset electronic components.

• Electrical circuit breaker may be tripped. Check

electrical service breaker box to verify.

• Defective surge protection device or electrical outlet.

Test outlet by plugging in another working appliance.

• Replace batteries in the hand control.

• Bed mechanism may be obstructed. Elevate bed and

check for obstruction. Remove obstruction.

• Head section may be too close to the wall.

• Headboard may be too close the edge of the mattress.

Verify a 1.5’” (38.1mm) to 2” (50.8mm) distance

between headboard brackets and mattress. Adjust if

required.

• Verify headboard brackets were removed during

installation. Remove headboard brackets if still

attached to the underneath side of bed.

• If bed is located on hard surface flooring, place carpet

pieces or rubber caster cups under each leg or caster

of the bed. (see accessory sheet, included with this

product, for rubber caster cup order information).

• Elevate the head or foot section a short distance (with

the hand control) to realign the lift/lower mechanisms

with the bed support platform.

• Verify that bed is not positioned against a wall,

nightstand, or other object that may cause vibration or

noise.

• If adjustable bed is installed over a bed frame, verify

massage motors are not causing bed frame (or bed

frame components) to vibrate.

• Verify that headboard attachment hardware is

tightened firmly (if used).

Excessive massage motor noise.

Head or foot section will elevate, but will notreturn to the horizontal (flat) position.

Hand control will not illuminate.

No features of the adjustable bed will activate.

Hand control illuminates and appears to beoperable, but will not activate bed.

SOLUTION

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

25

1-2-20 WARRANTY

FULL 1 YEAR WARRANTYThis adjustable bed is warranted againstdefects in the workmanship or materials fora period of one year from the warrantycommencement date. Upon notice duringthe first year after the warrantycommencement date, L&P will repair orreplace (at no cost to the purchaser) anydefective adjustable bed part, and L&P willpay all authorized labor and transportationcosts associated with the repair orreplacement of any parts found to bedefective.

2-YEAR LIMITED WARRANTYDuring the second year from the warrantycommencement date, upon receipt of notice,L&P will replace any adjustable bed partfound to be defective. This limited two yearwarranty shall not apply unless the defectivepart is returned to L&P within ten (10) days ofpurchaser’s receipt of the replacement part.Purchaser shall pay all service andtransportation costs related to thereplacement of the defective part.

20-YEAR LIMITED WARRANTYUpon notice during the third through thetwentieth years from the warrantycommencement date, L&P will replace, uponterms and conditions set forth in thisparagraph, any mechanical bed part foundto be defective. Electronics, electricalcomponents, drive motors and massagemotors are excluded. Purchaser shall pay 1/18of the then current replacement cost of thedefective part multiplied by the number of yearsafter two (2) years from the warrantycommencement date, and L&P shall bear the

Leggett & Platt, Incorporated (“L&P”) warrants this adjustable bed to the consumer who is theoriginal purchaser (the “purchaser”), subject to the terms and conditions set forth herein. Thiswarranty begins on the “warranty commencement date” which is the date of purchase for newunused beds and the date of manufacture for beds that have been used as floor or displaymodels. Thus, on a floor model bed, the warranty is a portion of the limited 20-year warranty.

remainder of the cost of the replacementpart. This twenty (20) year warranty shall notapply unless the defective part is returned toL&P within ten (10) days of purchaser’sreceipt of the replacement part. Purchasershall pay all service and transportation costsrelated to the replacement of the defectivepart. After the twentieth year, purchaser shallbear the entire cost of repair andreplacement of all parts and materials,including labor and transportation.

ADDITIONAL TERMS AND CONDITIONSThis warranty does not apply; (a) to anydamage caused by the purchaser; (b) if therehas been any repair or replacement ofadjustable bed parts by an unauthorizedperson; (c) if the adjustable bed has beenmishandled (whether in transit or by othermeans), subjected to physical or electricalabuse or misuse, or otherwise operated inany manner inconsistent with the operationand maintenance procedures outlined in theOwners Manual and this warranty; (d) todamage to mattresses, fabric, cables,electrical cords or items supplied by dealers.Contact the dealer for warranty informationon these items; (e) if there has been anymodification of the adjustable bed withoutprior written consent by L&P; (f) to costs forunnecessary service calls, including costsfor in-home service calls solely for thepurpose of educating the consumer aboutthe adjustable bed or finding anunsatisfactory power connection; (g) if therecommended weight restrictions are notfollowed (300-Twin; 375-Full; 425-Queen),the warranty will be void.

Continued on back of page...

Prec

isio

n C

omfo

rt™

Ow

ners

Man

ual

26

1-2-20 WARRANTY

Repairs to or replacement of an adjustablebed or its components under the terms ofthis limited warranty will apply to the originalwarranty period and will not serve to extendsuch period.

The decision to repair or to replace defectiveparts under this warranty shall be made, orcause to be made, by L&P at its option and inits sole discretion.

Repair or replacement shall be the soleremedy of the purchaser. There shall be noliability on the part of L&P for any special,indirect, incidental, or consequentialdamages or for any other damage, claim, orloss not expressly covered by the terms ofthis warranty.

This limited warranty does not includereimbursement for inconvenience,removal, installation, setup time, loss ofuse, shipping, or any other costs orexpenses. Leggett & Platt or its servicetechnicians shall not be responsible formoving furniture, removing headboards &footboards or any other items in order toperform service on your adjustable bed.

It is the sole responsibility of the purchaserto provide adequate space and accessibilityto the adjustable bed. In the event that thetechnician is unable to perform service dueto lack of accessibility, the service call will bebilled to the purchaser and the service willhave to be rescheduled.

L&P makes no other warranty whatever,express or implied, and all impliedwarranties of merchantability and fitnessfor a particular purpose are disclaimed byL&P and excluded from this agreement.

Some states do not allow the exclusion orlimitation of incidental or consequentialdamages, so the above limitation orexclusion may not apply to every purchaser.

This warranty gives the purchaser specificlegal rights, and the purchaser may alsohave other rights, which may vary from stateto state. This warranty is valid in all 50states, Puerto Rico, and Canada.

CONTACT INFORMATION

Select Comfort Customer Service Department

6105 Trenton Lane NorthMinneapolis, MN 55442

800-580-7216

Documents

OWNERS MANUALdl.owneriq.net/7/7a067e8c-5732-4c77-8d1d-237c40ae5f0e.pdfPrecision Comfort Owners Manual 7 MATTRESS RETAINER INSTALLATION 1.Before discarding any packing materials, check