Owner’s Manual - Pyle Audio – PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual INSTALLATION GUIDELINES Connecting the GND (GROUND) screw terminal Connecting

Owner’s Manual

PYLE PRO

AM

PLIFIERS

warranty registration card

Thank you for purchasing this PYLE

product. To activate your

warranty, please m

ail this card

within 10 days.

Nam

e

Address

City, State ZIP

Model N

o. Serial # (if available)

Date of Purchase

Purchased at: M

usic Products StoreCatalog M

erchandiser Sound C

ontractor/InstallerM

ail Order

Other

Please com

plete w

arranty card, detach

and retu

rn

All PYLE PRO products are carefully constructed and tested beforeshipment. Units purchased in the USA are warranted to be free ofdefects in material and workmanship for two (2) years from the dateof purchase. This warranty is limited to the original retail purchaserof the amplifier.

Should the unit fail due to factory defects in material or workmanship,your unit will be repaired or replaced at the sole discretion of PYLE.

To obtain warranty service, you must first call our Consumer ReturnHotline at (718) 236-6948 to obtain a Return Authorization Number.This R.A. # must appear on the outside of your package and on allpaperwork relating to your return.

When returning the unit to us for warranty service, it must be carefullypacked and shipped, prepaid, to:

R.A.#: _____________PYLE PRO Service Center1600 63rd StreetBrooklyn, NY 11204

You must also include the following items with your return:

• A copy of your sales receipt or other proof of purchase • A brief letter, indicating the problem you are experiencing with the product • Include in your letter your return address, daytime phone number and R.A. number • Also include a check or money order for $15.00 for return shipping, handling and insurance, or provide your Visa/MC number with expiration date.

Our obligation under this warranty is limited to the repair or replacementof the defective unit when it is returned to us prepaid. This warrantywill be considered void if the unit was tampered with, improperlyserviced or subject to misuse, neglect or accidental damage.

Limited Warranty

www.pyleaudio.com

P Z R 6 X A A m p l i f i e rP Z R 1 0 X A A m p l i f i e r

P Z R 3 0 X A A m p l i f i e rP Z R 5 0 X A A m p l i f i e r

PROTECT

MIN MAX

CLIPSIG

CHANNEL 1 CHANNEL 2

CLIP SIG

MIN MAX

POWER

CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIREREPLACE ONLY WITH SAME TYPE FUSE.

DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.CAUTION:

-30 -20 -15 -10 -5 0 +3-30 -20 -15 -10 -5 0 +3

POWER

CLIPSIG SIG CLIPPROTECT PROTECT

ON

OFF

1 Features and Controls, PZR6XA/10XA and PZR30XA/50XA2 Installation Guidelines2 Input Connections2 Connecting a CD, DVD or tape player or tuner2 Connecting an equalizer or signal processor2 Stereo or Mono Inputs2 Speaker connecitons3 Bridged Mode Operation4 Connecting to standard AC power4 Mounting the amplifier4 Turning the amplifier on4 Using the power LED meter4 Caring for your Pyle Pro Amplifier4 Using the channel1 and channel2 output level controls4 About the internal clip circuitry5 Specifications5 Limited warranty

TABLE OF CONTENTS

Please read this manual throughly before you attempt to set up and use the amplifier. It contains arange of installation suggestions as well as instructions to ensure safe usage. Installed properly, youcan expect years of trouble-free service from this product.

PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual – 1PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual

FEATURES AND CONTROLS

Protection Circuit and IndicatorThe indicator will be illuminated whenthe amplifier is powered on and at turn-on delay status; the indicator will beturned off after internal outputs areconnected. The indicator will also beilluminated when the amplifier hasabnormal problems, such as overloador excessive heat.

FEATURES AND CONTROLSFRONT PANEL, PZR30XA/50XA

FRONT PANEL, PZR6XA/PZR10XA

Channel 1 and Channel 2Output Level ControlsLets you adjust the sound levelsfor each channel. Clip Circuit and Indicator

This special circuitry protectsthe amplifier and speaker systemfrom being damaged byoverdriving power levels.Indicator lights remind the userto reduce the volume whenamplifier output is excessive.

Channel 1 and Channel 2 Power LED DisplayIndicate the output signal level for each channel.(PZR6XA without)

Power On/Off

Protection Circuit and IndicatorThe indicator will be illuminated whenthe amplifier is powered on and at turn-on delay status; the indicator will beturned off after internal outputs areconnected. The indicator will also beilluminated when the amplifier hasabnormal problems, such as overloador excessive heat.

Channel 1 and Channel 2Output Level ControlsLets you adjust the sound levelsfor each channel.

Clip Circuit and IndicatorThis special circuitry protects the amplifier and speaker systemfrom being damaged by overdriving power levels. Indicator lightsremind the user to reduce the volume when amplifier output isexcessive.

Power On/Off

Your New Pyle Pro PZR series P.A.Amplifier gives you the power andversatility you need in a professionalsound system.The amplifier's wide frequencyresponse makes it suitable foramplifying music or vocal programmaterial. It can be used for live bands,office paging systems, publicannouncements, or a variety of otherinstallations.

REAR PANEL, PZR6XA/10XA

Fan CoolingCooling system is automatically activated whenever amplifier is turned on.This forced air cooling system rapidly exhausts interior heat, reducing operatingtemperature and aiding performance.

Stereo/Mono SwitchLets you select conventionalstereo operation with astereo input signal or bridgedmono input mode.

Input JacksLet you connect a variety of audioinput sources via the balanced(XLR/6.35mm phone jackcombinations) or unbalanced (RCA)inputs.

REAR PANEL, PZR30XA/50XA

Fan CoolingCooling system is automatically activatedwhenever amplifier is turned on. This forcedair cooling system rapidly exhausts interiorheat, reducing operating temperature andaiding performance.

Stereo/Mono SwitchLets you select conventionalstereo operation with a stereoinput signal or bridgedmono input mode.

Input JacksLet you connect a variety of audioinput sources via the balanced(XLR/6.35mm phone jackcombinations) or unbalanced (RCA)inputs.

CH-2 CH-1

CH-2 CH-1

OUTPUTSCH-2

GND

CAUTION

TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)PLUG WITH AN EXTENSION CORD RECEPTACLEOR OTHER OUTLET UNLESS THE BLADES CAN BE FULLYINSERTED TO PREVENT BLADE EXPOSURE

CAUTION:

BRIDGE

CH-1

GROUND LIFT

GROUND LIFT

INPUTS

MONO

STEREO BRIDGE

12

3

HO

T(+

)C

OLD

(-)

GN

D(+

)

BALANCED INPUTS

RISK OF ELECTRIC SHOCKDO NOT OPEN

Channel 1 and Channel 2 Power LED DisplayIndicate the output signal level for each channel.

AC 120V 60HZ~

ON

OFF

CHANNEL 2

MIN MAX

CHANNEL 1

MIN MAX

LOW CAPACITANCE SHIELDED WIRE GROUNDSCREW

EQ OR MIXER

PREAMP OR MIXER

EQ OR MIXER













PREAMP OR MIXER

CD PLAYER, TAPE PLAYEROR TUNER

EQ OR MIXER

EQ OR MIXER

2 – PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual

INSTALLATION GUIDELINES

Connecting the GND (GROUND) screw terminal Connectinga mixer or preamplifier may cause excessive noise or humin the amplifier output. To prevent this, connect one endof a low-capacitance shield wire to the amplifier's groundscrew (on the rear panel). Then connect the other end ofthis wire to the ground terminal on the mixer or preamplifierenclosure.

LOW CAPACITANCE SHIELD WIRE

GROUND SCREW

Input connectionsThese amplifiers accept a board range of input sources,including Compact Disc (CD,DVD) players; Cassette, Reel-to-Reel or other tape players; Radio Tuners; Equalizers;Signal Processors.

Connecting a CD, DVD, tape player or tunerIn a normal installation, one would use the RCA JACKS forconnecting a CD player, DVD player,tape player or tuner.

use RCA jacks

Connecting an equalizer or external signal processorConnect the processor's OUT to the amplifier's IN connector.

use XLR/6.35mm combo jacks

Speaker connectionsYou can connect 4 Ohm, 8 Ohm or 16 Ohm speakers toChannel 1 and/or Channel 2 of the amplifier. If you connecttwo pairs of speakers, be sure to follow these guidelines:

• Speakers which are connected to the same channel arepart of a pair, and must be of the same impedance.

• Speakers connected to different channels are NOT partof a pair, and can be of different impedances.

1. Prepare the speaker wire by removing about 1 inch ofinsulation from the end of the speaker wire you intend toconnect to the amplifier. Then twist the exposed wire tosecure all the wire strands.

NOTE: Use 16-gauge speaker wire for lengths up to25 feet; 14-gauge wire for lengths over 25 feet. It is recommended that you use the shortest length of wire possible.

2. Connect the speaker wires to the speaker's positive andnegative terminals.

NOTE: Most speaker terminals are either color-coded or have a mark that indicates the terminal's polarity. Usually positive terminals are red or have a plus symbol (+), and negative terminals are black or have a minus symbol (-).

3. Connect the speaker wires to the amplifier's left andright speaker terminals according to the terminal colorpolarity.

Stereo or Mono InputsYour Pyle Pro amplifier can be operated in Stereo, Mono orBridged mode, depending on the input source. If the inputsignal is mono, slide the Stereo/Mono/Bridged selectorswitch to MONO and the signal will be routed through bothchannels. If you wish to run the amplifier in bridged outputmode, slide the switch to Bridged.

SWITCH IN “STEREO” POSITION

STEREO OPERATION

STEREO SIGNAL SOURCE

CH 2 CH 1

CAUTION! Do not usebalanced and unbalancedinputs simultaneously!!

Bridged Mode OperationThis amplifier can operate in a mono bridged output mode, ifyour speakers can handle the following power output levels:

As shown in the diagram below, connect the speaker's positive(+) to the amplifier's red speakers left (1/2) terminals andnegative (-) to red speakers right (1/2) terminals.

The speaker right (+) on the amplifier is used as a negative (-)terminal for a bridged connection.

NOTE: The extra amplifier output of 6.35mm phonejacks can not be used for the bridged connection. It can onlybe used in normal (non-bridged) operation as a stereo speakeroutput.

MONO SIGNAL SOURCEUSECHANNEL 1INPUT ONLY


CH 2 CH 1

MONO SIGNAL SOURCE USECHANNEL 1INPUT ONLY

SWITCH IN “BRIDGED” POSITIONMONO BRIDGED OPERATION


DO NOT USEBLACK TERMINALS

PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual – 3

SWITCH IN “MONO” POSITIONMONO OPERATION

CH 2 CH 1CD PLAYER, DVD , TAPE PLAYEROR TUNER

use RCA jacks

use XLR/6.35 mmcombo jacks

STEREO SIGNAL SOURCE


CH 2 CH 1



DO NOT USEBLACK TERMINALS


CH-2 CH-1

CH-2 CH-1

OUTPUTSCH-2

GND

CAUTION


CAUTION:

BRIDGE

CH-1

GROUND LIFT

GROUND LIFT

INPUTS

MONO

STEREO BRIDGE

12

3

HO

T(+

)C

OLD

(-)

GN

D(+

)

BALANCED INPUTS


CH-2 CH-1

CH-2 CH-1

OUTPUTSCH-2

GND

CAUTION


CAUTION:

BRIDGE

CH-1

GROUND LIFT

GROUND LIFT

INPUTS

MONO

STEREO BRIDGE

12

3

HO

T(+

)C

OLD

(-)

GN

D(+

)

BALANCED INPUTS


CH-2 CH-1

CH-2 CH-1

OUTPUTSCH-2

GND

CAUTION


CAUTION:

BRIDGE

CH-1

GROUND LIFT

GROUND LIFT

INPUTS

MONO

STEREO BRIDGE

12

3

HO

T(+

)C

OLD

(-)

GN

D(+

)

BALANCED INPUTS


CH-2 CH-1

CH-2 CH-1

OUTPUTSCH-2

GND

CAUTION


CAUTION:

BRIDGE

CH-1

GROUND LIFT

GROUND LIFT

INPUTS

MONO

STEREO BRIDGE

12

3

HO

T(+

)C

OLD

(-)

GN

D(+

)

BALANCED INPUTS


CH-2 CH-1

CH-2 CH-1

OUTPUTSCH-2

GND

CAUTION


CAUTION:

BRIDGE

CH-1

GROUND LIFT

GROUND LIFT

INPUTS

MONO

STEREO BRIDGE

12

3

HO

T(+

)C

OLD

(-)

GN

D(+

)

BALANCED INPUTS


CH-2 CH-1

CH-2 CH-1

OUTPUTSCH-2

GND

CAUTION


CAUTION:

BRIDGE

CH-1

GROUND LIFT

GROUND LIFT

INPUTS

MONO

STEREO BRIDGE

12

3

HO

T(+

)C

OLD

(-)

GN

D(+

)

BALANCED INPUTS


AC 120V 60HZ~

AC 120V 60HZ~

AC 120V 60HZ~

AC 120V 60HZ~

AC 120V 60HZ~

AC 120V 60HZ~

Amplifier Specifications

Input Impedance, balanced (unbalanced)

Continuous Output Power

Stereo Mode20 Hz to 20 kHz, 8 Ohms1 kHz, 4 OhmsMaximum Power, 8 OhmsMaximum Power, 4 OhmsPeak Power, 8 Ohms

Bridged Mode20 Hz to 20 kHz, 8 Ohms1 kHz, 8 OhmsPeak Power

THD at rated output power

Frequency Response +/– 3 dB

Input Sensitivity for rated output power

Signal-to-Noise Ratio A-Weighted

Speaker ImpedanceStereoBridged

Power Requirement

Dimensions H x W x D, inches(mm)

Weight, lbs (kg)

120 VAC, 60 Hz / 230 VAC, 50 Hz 120 VAC, 60 Hz120 VAC, 60 Hz

4 – PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual - 5

PYLE

PRO

Aud

io,

Inc.

1600

63r

d St

reet

Broo

klyn

, N

Y 11

204

Plac

eSt

amp

Her

e

Connecting to standard AC powerAfter making all other connections, set the POWER switchto OFF position. Then connect the power cord to a standardAC outlet.

Mounting the amplifierThis amplifier is designed to accept standard rack mountinginstallations. Two slots on each end of the front panel makeit suitable for such an installation.

Tightly secure four mounting screws (not supplied) throughthese fours slots and into your standard electronics equipmentrack.

Turning the amplifier on1. Turn on the audio input source equipment which isconnected to the amplifier INPUT jacks.

2. Set the amplifier’s Channel 1 and Channel 2 output levelgain controls to the minimum level settings.

3. Push in the power switch to turn the amplifier on.

Using the power blue LED metersThe meter pointer position indicates the amplifier outputpower. For ease of reading in dark environments, the meteris illuminated.

Using the Channel 1 and Channel 2 Output Level controlsRotate output level gain clockwise to increase, or counter-clockwise to decrease the output power. To get the bestperformance with the least sound distortion, always adjustthe output level gain so the meter's pointer does notcontinuously exceed the extreme right of the meter's scale.

CAUTION: It is possible to overdrive the amplifier by setting output level gain too high, which may cause damage or failure.

About the internal clip circuitrySpecial clip circuitry incorporated into your Pyle Proamplifier’s design protects the amplifier and speaker systemfrom being damaged from overdriving power.

Under normal conditions, the amplifier’s clip indicator willflicker as the output power momentarily exceeds the levelas set by the output level gain selector.

However, under excessive output conditions, the clipindicator lights remain on continuously, alerting you thatthe special clip circuitry has become active. When thisoccurs, you should simply reduce the output power levelby rotating the Master Volume control counterclockwise.

All PYLE PRO products are carefully constructed and tested before shipment.Units purchased in the USA are warranted to be free of defects in materialand workmanship for two (2) years from the date of purchase. This warrantyis limited to the original retail purchaser of the amplifier.

Should the unit fail due to factory defects in material or workmanship, yourunit will be repaired or replaced at the sole discretion of PYLE.

To obtain warranty service, you must first call our Consumer Return Hotlineat (718) 236-6948 to obtain a Return Authorization Number. This R.A. # mustappear on the outside of your package and on all paperwork relating to yourreturn.

When returning the unit to us for warranty service, it must be carefully packedand shipped, prepaid, to:

R.A.#: _____________PYLE PRO Service Center1600 63rd StreetBrooklyn, NY 11204

You must also include the following items with your return:

• A copy of your sales receipt or other proof of purchase • A brief letter, indicating the problem you are experiencing with the

product • Include in your letter your return address, daytime phone number and

R.A. number • Also include a check or money order for $15.00 for return shipping,

handling and insurance, or provide your Visa/MC number with expiration date.

Our obligation under this warranty is limited to the repair or replacement ofthe defective unit when it is returned to us prepaid. This warranty will beconsidered void if the unit was tampered with, improperly serviced or subjectto misuse, neglect or accidental damage.

Limited Warranty

20 k-Ohms (10 k-Ohms)

70W x 2100W x 2110W x 2130W x 2

1100W x 2

175W x 1200W x 1

2200W x 1

0.1%

10 Hz to 50 kHz

1.0V

100 dB

4-16 Ohms8-16 Ohms

3 15/32 x 19 x 10 11/16

(88 x 482 x 271)

16.5 (7.5)

PZR6XA


170W x 2220W x 2230W x 2260W x 2

1650W x 2

380W x 1440W x 1

3300W x 1

0.1%

10 Hz to 50 kHz

1.0V

100 dB

4-16 Ohms8-16 Ohms

3 15/32 x 19 x 10 11/16

(88 x 482 x 271)

20.02 (9.1)

PZR10XA

Caring for your Pyle Pro AmplifierYour Pyle Pro Amplifier is an example of superior designand craftsmanship. The following suggestions will help youcare for your amplifier so you can enjoy years of use:

• Keep the amplifier dry. If it gets wet, wipe immediately.• Use the amplifier only in well-ventilated installations.• Handle the amplifier gently and carefully - do not drop!• Keep the amplifier away from dust and dirt.• Wipe occasionally with a damp cloth to keep it looking

new. Do not use harsh chemicals, solvents or detergents!


200W x 2300W x 2230W x 2350W x 2

2200W x 2

500W x 1600W x 1

4400W x 1

0.1%

10 Hz to 50 kHz

1.0V

100 dB

4-16 Ohms8-16 Ohms

5 3/16 x 19 x 15 3/8

(132 x 482 x 390)

28.16 (12.8)

PZR30XA


260W x 2400W x 2300W x 2450W x 2

2750W x 2

700W x 1800W x 1

5500W x 1

0.1%

10 Hz to 50 kHz

1.0V

100 dB

4-16 Ohms8-16 Ohms

5 3/16 x 19 x 15 3/8

(132 x 482 x 390)

29.7 (13.5)

PZR50XA

Documents

Owner’s Manual - Pyle Audio – PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual INSTALLATION GUIDELINES Connecting the GND (GROUND) screw terminal Connecting