Embed Size (px)
Citation preview
4 1/2" or 3/4" MNPT rigid vessel connection, with 5/8" or 3/4" OD Gauge Glass Connection
4 500 psi Working Pressure
4 Inline Vent and Drain connection
4 All valves are supplied with 316 Stainless Steel Valve Stem, Ball Check, and Stem packing washer
4 All assemblies are Hydro tested to 750 psi
Environmental Sealed Gauge (ESG)
4 Replaces unprotected gauge glass, eliminates two most common breakage points, Stainless Steel nozzles
The Superior Products Gauge Cocks are manufactured to offer a higher standard in sight flow indication management. The bodies are made in a forging process vs. a casting process, with each body pressure tested to assure quality. Forged products are stronger and more reliable than that of castings. When used in combination with the Superior Products Gauge Glass and Glass Guards this trifecta will provide a superior amount of operator and environmental safety.
Superior Products manufactures the Industry Legacy (old school) design and Now offers the New Innovative Hammer Union design.
Listed below are several reasons the Industry is changing and asking for the Patent PendingHammer Union Design.
4 Cost of ownership for the BPR’s life cycle 4 Built in Safety Factor 4 End-user Approved/Proven in the Field 4 Faster Field Repair/Inline Repairable 4 Fewer Tools Required 4 No More Rope Packing Leaks 4 HNBR Loaded Seal Design 4 Up to 5,000 psi working pressure 4 Maintain Pressure Settings during Repair 4 All Internals Interchangeable with Competitors*
It’s a no brainer. Order your Hammer Union Design today and start saving your Precious Time and Money!
Place your order with the local Representative or Call Superior Products direct 888-634-4717
Old School or the NeW hAMMer UNIoN DeSIGN
quick. safe. durable.*Consult Factory to Confirm
www.sup-prod.comPlace your order with the local Representative or Call Superior Products direct 888-634-4717
WARNING: Superior Products is not responsible for improper installation. Improper installation can cause glass breakage, which may result in bodily injury and dangerous accidents.
Gauge Cocks Carbon & Stainless Steel Design/Features:
4 1/2" MNPT Fittings
4 Available with dual bleeders
4 Ball Checks are standard
4 Rated @ 200 psig @ 400 degrees F, or 400 psig @ 100 degrees F
Gauge Cocks Brass Design/Features:
4 Red Line or Transparent, Standard, High Pressure, or Heavy Wall
Gauge Glass:
OVERVIEW
Gauge Guards:
4 Used to prevent breakage of Gauge Glass
TO CONTACT SUPERIOR PRODUCTS, CALL (888) 634-4717 OR EMAIL [email protected] Old Highway 40, Junction City, KS, 66441©2019 Superior Products, All rights reserved • SP-GaugeCGG-flyer-July-2019-tmm-ig • Superior reserves the right to change designs, materials, or specifications without notice or without obligation to furnish or install such changes on products previously or subsequently sold. Nothing in this brochure is intended to extend any type of warranty, expressed or implied.
AVAILABLE AT:
OTHER PRODUCTS
4 Bleed Rings4 Closures4 Pig Signals4 Chemical Injection
Pumps 4 Chemical Atomizers
FLOW CONTROL
4 BPR’S• Traditional• Hammer Union• Extreme
4 CHOKES• 2” 5000# N60• 2” Mini Choke• 3” Mini Choke• H2 Profile• JWA Profile
4 SPRING LOADED BALL CHECKS• 1/4” 6000PSI• 1/2” 6000PSI• 1” 3000PSI• 2” 2000PSI• 3” 2000PSI
TANK & FABRICATION
4 GAUGE COCKS• Carbon Steel• Stainless Steel• Brass
4 GAUGES• Environmentally
Sealed Gauge (ESG)• Gauge Glass• Glass Guards
4 LEVEL CONTROLLERS• 2” Pneumatic• 4” Pneumatic• 8” Mechanical
4 BIRD CAGES
Ask about our Patent Pending
Design
TCL k
Phone: (888) 634-4717Fax: (785) 579-4758
www.sup-prod.com
