Order Codes

Embed Size (px)

Citation preview

  • 8/13/2019 Order Codes

    1/6

    GE Multilin F35 Multiple Feeder Protection System 2-3

    2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

    b) ORDER CODES WITH TRADITIONAL CTS AND VTS

    The order codes for the horizontal mount units with traditional CTs and VTs are shown below.

    Table 23: F35 ORDER CODES (HORIZONTAL UNITS)F35 - * ** - * * * - F ** - H ** - M ** - P ** - U ** - W/X ** Full Size Horizontal Mount

    BASE UNIT F35 | | | | | | | | | | | Base UnitCPU E | | | | | | | | | | RS485 and RS485

    G | | | | | | | | | | RS485 and multi-mode ST 10Base-FH | | | | | | | | | | RS485 and multi-mode ST redundant 10Base-F

    J | | | | | | | | | | RS485 and multi-mode ST 100Base-FXK | | | | | | | | | | RS485 and multi-mode ST redundant 100Base-FXL | | | | | | | | | | RS485 and single mode SC 100Base-FXM | | | | | | | | | | RS485 and single mode SC redundant 100Base-FXN | | | | | | | | | | RS485 and 10/100Base-TP | | | | | | | | | | RS485 and single mode ST 100Base-FXR | | | | | | | | | | RS485 and single mode ST redundant 100Base-FXS | | | | | | | | | | RS485 and six-port managed Ethernet switch

    SOFTWARE 00 | | | | | | | | | No Software Options01 | | | | | | | | | Ethernet Global Data (EGD); not available for Type E CPUs03 | | | | | | | | | IEC 61850; not available for Type E CPUs04 | | | | | | | | | Ethernet Global Data (EGD) and IEC 61850; not available for Type E CPUs

    MOUNT/COATING H | | | | | | | | Horizontal (19 rack)A | | | | | | | | Horizontal (19 rack) with harsh environmental coating

    FACEPLATE/ DISPLAY C | | | | | | | English displayD | | | | | | | French displayR | | | | | | | Russian displayA | | | | | | | Chinese displayP | | | | | | | English display with 4 small and 12 large programmable pushbuttonsG | | | | | | | French display with 4 small and 12 large programmable pushbuttonsS | | | | | | | Russian display with 4 small and 12 large programmable pushbuttonsB | | | | | | | Chinese display with 4 small and 12 large programmable pushbuttonsK | | | | | | | Enhanced front panel with English displayM | | | | | | | Enhanced front panel with French displayQ | | | | | | | Enhanced front panel with Russian displayU | | | | | | | Enhanced front panel with Chinese displayL | | | | | | | Enhanced front panel with English display and user-programmable pushbuttonsN | | | | | | | Enhanced front panel with French display and user-programmable pushbuttonsT | | | | | | | Enhanced front panel with Russian display and user-programmable pushbuttonsV | | | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons

    POWER SUPPLY

    (redundant supply must

    be same type as main supply)

    H | | | | | | 125 / 250 V AC/DC power supplyH | | | | | RH 125 / 250 V AC/DC with redundant 125 / 250 V AC/DC power supplyL | | | | | | 24 to 48 V (DC only) power supplyL | | | | | RL 24 to 48 V (DC only) with redundant 24 to 48 V DC power supply

    CT/VT MODULES 8F | 8F | 8F | Standard 4CT/4VT8G | 8G | 8G | Sensitive Ground 4CT/4VT8H | 8H | 8H | Standard 8CT8J | 8J | 8J | Sensitive Ground 8CT8L | 8L | 8L | Standard 4CT/4VT with enhanced diagnostics8M | 8M | 8M | Sensitive Ground 4CT/4VT with enhanced diagnostics8N | 8N | 8N | Standard 8CT with enhanced diagnostics8R | 8R | 8R | Sensitive Ground 8CT with enhanced diagnostics

    DIGITAL INPUTS/OUTPUTS XX XX XX XX XX No Module4A 4A 4A 4A 4A 4 Solid-State (no monitoring) MOSFET outputs4B 4B 4B 4B 4B 4 Solid-State (voltage with optional current) MOSFET outputs4C 4C 4C 4C 4C 4 Solid-State (current with optional voltage) MOSFET outputs4D 4D 4D 4D 4D 16 digital inputs with Auto-Burnishing4L 4L 4L 4L 4L 14 Form-A (no monitoring) Latching outputs67 67 67 67 67 8 Form-A (no monitoring) outputs6A 6A 6A 6A 6A 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs6B 6B 6B 6B 6B 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs6C 6C 6C 6C 6C 8 Form-C outputs6D 6D 6D 6D 6D 16 digital inputs6E 6E 6E 6E 6E 4 Form-C outputs, 8 digital inputs6F 6F 6F 6F 6F 8 Fast Form-C outputs6G 6G 6G 6G 6G 4 Form-A (voltage with optional current) outputs, 8 digital inputs6H 6H 6H 6H 6H 6 Form-A (voltage with optional current) outputs, 4 digital inputs6K 6K 6K 6K 6K 4 Form-C and 4 Fast Form-C outputs6L 6L 6L 6L 6L 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs6M 6M 6M 6M 6M 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs6N 6N 6N 6N 6N 4 Form-A (current with optional voltage) outputs, 8 digital inputs6P 6P 6P 6P 6P 6 Form-A (current with optional voltage) outputs, 4 digital inputs6R 6R 6R 6R 6R 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs

    6S 6S 6S 6S 6S 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs6T 6T 6T 6T 6T 4 Form-A (no monitoring) outputs, 8 digital inputs6U 6U 6U 6U 6U 6 Form-A (no monitoring) outputs, 4 digital inputs6V 6V 6V 6V 6V 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs

    TRANSDUCER

    INPUTS/OUTPUTS

    (select a maximum of 3 per unit)

    5A 5A 5A 5A 5A 4 dcmA inputs, 4 dcmA outputs (only one 5A module is allowed)5C 5C 5C 5C 5C 8 RTD inputs5D 5D 5D 5D 5D 4 RTD inputs, 4 dcmA outputs (only one 5D module is allowed)5E 5E 5E 5E 5E 4 RTD inputs, 4 dcmA inputs5F 5F 5F 5F 5F 8 dcmA inputs

    INTER-RELAY

    COMMUNICATIONS

    (select a maximum of 1 per unit)

    2A 2A C37.94SM, 1300nm single-mode, ELED, 1 channel single-mode2B 2B C37.94SM, 1300nm single-mode, ELED, 2 channel single-mode2E 2E Bi-phase, single channel2F 2F Bi-phase, dual channel2G 2G IEEE C37.94, 820 nm, 128 kbps, mul timode, LED, 1 Channe l2H 2H IEEE C37.94, 820 nm, 128 kbps, mul timode, LED, 2 Channe ls| 2S Six-port managed Ethernet switch with high voltage power supply (110 to 250 V DC / 100 to 240 V AC)| 2T Six-port managed Ethernet switch wi th low vol tage power supply (48 V DC)

    72 72 1550 nm, single-mode, LASER, 1 Channel73 73 1550 nm, single-mode, LASER, 2 Channel74 74 Channe l 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER75 75 Channe l 1 - G.703; Channe l 2 - 1550 nm, Single-mode LASER76 76 IEEE C37.94, 820 nm, 64 kbps, mult imode, LED, 1 Channel77 77 IEEE C37.94, 820 nm, 64 kbps, mult imode, LED, 2 Channels7A 7A 820 nm, multi-mode, LED, 1 Channel7B 7B 1300 nm, multi-mode, LED, 1 Channel7C 7C 1300 nm, single-mode, ELED, 1 Channel7D 7D 1300 nm, single-mode, LASER, 1 Channel7E 7E Channel 1 - G.703; Channel 2 - 820 nm, multi-mode7F 7F Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode7G 7G Channe l 1 - G.703; Channe l 2 - 1300 nm, s ing le-mode ELED7H 7H 820 nm, multi-mode, LED, 2 Channels

    7I 7I 1300 nm, multi-mode, LED, 2 Channels7J 7J 1300 nm, single-mode, ELED, 2 Channels7K 7K 1300 nm, single-mode, LASER, 2 Channels7L 7L Channe l 1 - RS422; Channel 2 - 820 nm, mu lt i-mode, LED7M 7M Channe l 1 - RS422; Channel 2 - 1300 nm, mul ti -mode, LED7N 7N Channe l 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED7P 7P Channe l 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER7Q 7Q Channe l 1 - G.703; Channe l 2 - 1300 nm, s ing le-mode LASER7R 7R G.703, 1 Channel7S 7S G.703, 2 Channels7T 7T RS422, 1 Channel7W 7W RS422, 2 Channels

  • 8/13/2019 Order Codes

    2/6

    2-4 F35 Multiple Feeder Protection System GE Multilin

    2.1 INTRODUCTION 2 PRODUCT DESCRIPTION

    2

    The order codes for the reduced size vertical mount units with traditional CTs and VTs are shown below.

    Table 24: F35 ORDER CODES (REDUCED SIZE VERTICAL UNITS)F35 - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)

    BASE UNIT F35 | | | | | | | | | Base UnitCPU E | | | | | | | | RS485 and RS485

    G | | | | | | | | RS485 and multi-mode ST 10Base-FH | | | | | | | | RS485 and multi-mode ST redundant 10Base-FJ | | | | | | | | RS485 and multi-mode ST 100Base-FXK | | | | | | | | RS485 and multi-mode ST redundant 100Base-FXL | | | | | | | | RS485 and single mode SC 100Base-FX

    M | | | | | | | | RS485 and single mode SC redundant 100Base-FXN | | | | | | | | RS485 and 10/100Base-TP | | | | | | | | RS485 and single mode ST 100Base-FXR | | | | | | | | RS485 and single mode ST redundant 100Base-FX

    SOFTWARE 00 | | | | | | | No Software Options01 | | | | | | | Ethernet Global Data (EGD); not available for Type E CPUs03 | | | | | | | IEC 61850; not available for Type E CPUs04 | | | | | | | Ethernet Global Data (EGD) and IEC 61850; not available for Type E CPUs

    MOUNT/COATING V | | | | | | Vertical (3/4 rack)B | | | | | | Vertical (3/4 rack) with harsh environmental coating

    FACEPLATE/ DISPLAY C | | | | | English displayD | | | | | French displayR | | | | | Russian displayA | | | | | Chinese displayK | | | | | Enhanced front panel with English displayM | | | | | Enhanced front panel with French displayQ | | | | | Enhanced front panel with Russian displayU | | | | | Enhanced front panel with Chinese displayL | | | | | Enhanced front panel with English display and user-programmable pushbuttonsN | | | | | Enhanced front panel with French display and user-programmable pushbuttonsT | | | | | Enhanced front panel with Russian display and user-programmable pushbuttonsV | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons

    POWER SUPPLY H | | | | 125 / 250 V AC/DC power supplyL | | | | 24 to 48 V (DC only) power supply

    CT/VT MODULES 8F | 8F | Standard 4CT/4VT8G | 8G | Sensitive Ground 4CT/4VT8H | 8H | Standard 8CT8J | 8J | Sensitive Ground 8CT8L | 8L | Standard 4CT/4VT with enhanced diagnostics8M | 8M | Sensitive Ground 4CT/4VT with enhanced diagnostics

    8N | 8N | Standard 8CT with enhanced diagnostics8R | 8R | Sensitive Ground 8CT with enhanced diagnostics

    DIGITAL INPUTS/OUTPUTS XX XX XX No Module4A 4A 4A 4 Solid-State (no monitoring) MOSFET outputs4B 4B 4B 4 Solid-State (voltage with optional current) MOSFET outputs4C 4C 4C 4 Solid-State (current with optional voltage) MOSFET outputs4D 4D 4D 16 digital inputs with Auto-Burnishing4L 4L 4L 14 Form-A (no monitoring) Latching outputs67 67 67 8 Form-A (no monitoring) outputs6A 6A 6A 2 Form-A (voltage wit h opt ional current ) and 2 Form-C outputs, 8 digital inputs6B 6B 6B 2 Form-A (voltage wit h opt ional current ) and 4 Form-C outputs, 4 digital inputs6C 6C 6C 8 Form-C outputs6D 6D 6D 16 digital inputs6E 6E 6E 4 Form-C outputs, 8 digital inputs6F 6F 6F 8 Fast Form-C outputs6G 6G 6G 4 Form-A ( voltage wit h opt ional current ) outp uts, 8 digital inputs6H 6H 6H 6 Form-A ( voltage wit h opt ional current ) outp uts, 4 digital inputs6K 6K 6K 4 Form-C and 4 Fast Form-C outputs6L 6L 6L 2 Form-A (current wit h opt ional voltage) and 2 Form-C outputs, 8 digital inputs6M 6M 6M 2 Form-A (current w ith opt ional vol tage) and 4 Form-C outputs, 4 d igi ta l i nputs6N 6N 6N 4 Form-A ( current wit h opt ional voltage) outp uts, 8 digital inputs6P 6P 6P 6 Form-A ( current wit h opt ional voltage) outp uts, 4 digital inputs6R 6R 6R 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs6S 6S 6S 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs6T 6T 6T 4 Form-A (no monitoring) outputs, 8 digital inputs6U 6U 6U 6 Form-A (no monitoring) outputs, 4 digital inputs6V 6V 6V 2 Form-A ou tputs, 1 Form-C output , 2 Form-A (no moni to ring) la tching outpu ts , 8 digi ta l i nputs

    TRANSDUCER

    INPUTS/OUTPUTS

    (select a maximum of 3 per unit)

    5A 5A 5A 4 dcmA inputs, 4 dcmA outputs (only one 5A module is allowed)5C 5C 5C 8 RTD inputs5D 5D 5D 4 RTD inputs, 4 dcmA outputs (only one 5D module is allowed)5E 5E 5E 4 RTD inputs, 4 dcmA inputs5F 5F 5F 8 dcmA inputs

    INTER-RELAY

    COMMUNICATIONS

    (select a maximum of 1 per unit)

    For the last module, slot P is used for digital and transducer

    input/output modules; slot R is used for inter-relay

    communications modules.

    2A C37.94SM, 1300nm single-mode, ELED, 1 channel single-mode2B C37.94SM, 1300nm single-mode, ELED, 2 channel single-mode2E Bi-phase, single channel2F Bi-phase, dual channel2G IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel2H IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels72 1550 nm, single-mode, LASER, 1 Channel73 1550 nm, single-mode, LASER, 2 Channel74 Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER75 Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels7A 820 nm, multi-mode, LED, 1 Channel7B 1300 nm, multi-mode, LED, 1 Channel7C 1300 nm, single-mode, ELED, 1 Channel7D 1300 nm, single-mode, LASER, 1 Channel7E Channel 1 - G.703; Channel 2 - 820 nm, multi-mode7F Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED7H 820 nm, multi-mode, LED, 2 Channels7I 1300 nm, multi-mode, LED, 2 Channels7J 1300 nm, single-mode, ELED, 2 Channels7K 1300 nm, single-mode, LASER, 2 Channels7L Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED7M Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER

    7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER7R G.703, 1 Channel7S G.703, 2 Channels7T RS422, 1 Channel7W RS422, 2 Channels

  • 8/13/2019 Order Codes

    3/6

    GE Multilin F35 Multiple Feeder Protection System 2-5

    2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

    c) ORDER CODES WITH PROCESS BUS MODULES

    The order codes for the horizontal mount units with the process bus module are shown below.

    Table 25: F35 ORDER CODES (HORIZONTAL UNITS WITH PROCESS BUS)F35 - * ** - * * * - F ** - H ** - M ** - P ** - U ** - W/X ** Full Size Horizontal Mount

    BASE UNIT F35 | | | | | | | | | | | Base UnitCPU E | | | | | | | | | | RS485 and RS485

    G | | | | | | | | | | RS485 and multi-mode ST 10Base-FH | | | | | | | | | | RS485 and multi-mode ST redundant 10Base-F

    J | | | | | | | | | | RS485 and multi-mode ST 100Base-FXK | | | | | | | | | | RS485 and multi-mode ST redundant 100Base-FXL | | | | | | | | | | RS485 and single mode SC 100Base-FXM | | | | | | | | | | RS485 and single mode SC redundant 100Base-FXN | | | | | | | | | | RS485 and 10/100Base-TP | | | | | | | | | | RS485 and single mode ST 100Base-FXR | | | | | | | | | | RS485 and single mode ST redundant 100Base-FX

    SOFTWARE 00 | | | | | | | | | No Software Options01 | | | | | | | | | Ethernet Global Data (EGD); not available for Type E CPUs03 | | | | | | | | | IEC 61850; not available for Type E CPUs04 | | | | | | | | | Ethernet Global Data (EGD) and IEC 61850; not available for Type E CPUs

    MOUNT/COATING H | | | | | | | | Horizontal (19 rack)A | | | | | | | | Horizontal (19 rack) with harsh environmental coating

    FACEPLATE/ DISPLAY C | | | | | | | English displayD | | | | | | | French displayR | | | | | | | Russian displayA | | | | | | | Chinese displayP | | | | | | | English display with 4 small and 12 large programmable pushbuttonsG | | | | | | | French display with 4 small and 12 large programmable pushbuttonsS | | | | | | | Russian display with 4 small and 12 large programmable pushbuttonsB | | | | | | | Chinese display with 4 small and 12 large programmable pushbuttonsK | | | | | | | Enhanced front panel with English displayM | | | | | | | Enhanced front panel with French displayQ | | | | | | | Enhanced front panel with Russian displayU | | | | | | | Enhanced front panel with Chinese displayL | | | | | | | Enhanced front panel with English display and user-programmable pushbuttonsN | | | | | | | Enhanced front panel with French display and user-programmable pushbuttonsT | | | | | | | Enhanced front panel with Russian display and user-programmable pushbuttonsV | | | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons

    POWER SUPPLY

    (redundant supply must

    be same type as main supply)

    H | | | | | | 125 / 250 V AC/DC power supplyH | | | | | RH 125 / 250 V AC/DC with redundant 125 / 250 V AC/DC power supplyL | | | | | | 24 to 48 V (DC only) power supplyL | | | | | RL 24 to 48 V (DC only) with redundant 24 to 48 V DC power supply

    PROCESS BUS MODULE | 81 | | | | Eight-port digital process bus moduleDIGITAL INPUTS/OUTPUTS XX XX XX XX XX No Module

    4A 4A | 4 Solid-State (no monitoring) MOSFET outputs4B 4B | 4 Solid-State (voltage with optional current) MOSFET outputs4C 4C | 4 Solid-State (current with optional voltage) MOSFET outputs4D 4D | 16 digital inputs with Auto-Burnishing4L 4L | 14 Form-A (no monitoring) Latching outputs67 67 | 8 Form-A (no monitoring) outputs6A 6A | 2 Form-A ( voltage wit h optional cur rent) and 2 Form-C outputs, 8 digit al inputs6B 6B | 2 Form-A ( voltage wit h optional cur rent) and 4 Form-C outputs, 4 digit al inputs6C 6C | 8 Form-C outputs6D 6D | 16 digital inputs6E 6E | 4 Form-C outputs, 8 digital inputs6F 6F | 8 Fast Form-C outputs6G 6G | 4 Form-A (voltage with optional current) outputs, 8 digital inputs6H 6H | 6 Form-A (voltage with optional current) outputs, 4 digital inputs6K 6K | 4 Form-C and 4 Fast Form-C outputs6L 6L | 2 Form-A ( cur rent with optional voltage) and 2 Form-C outputs, 8 digit al inputs6M 6M | 2 Form-A ( cur rent with optional voltage) and 4 Form-C outputs, 4 digit al inputs6N 6N | 4 Form-A (current with optional voltage) outputs, 8 digital inputs6P 6P | 6 Form-A (current with optional voltage) outputs, 4 digital inputs6R 6R | 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs6S 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs6T 6T | 4 Form-A (no monitoring) outputs, 8 digital inputs6U 6U | 6 Form-A (no monitoring) outputs, 4 digital inputs6V 6V | 2 Form-A outpu ts , 1 Form-C output , 2 Form-A (no monitor ing) la tch ing outpu ts , 8 d ig ital i npu ts

    INTER-RELAY

    COMMUNICATIONS

    (select a maximum of 1 per unit)

    2A 2A C37.94SM, 1300nm sing le -mode, ELED, 1 channel s ingle -mode2B 2B C37.94SM, 1300nm sing le -mode, ELED, 2 channel s ingle -mode2E 2E Bi-phase, single channel2F 2F Bi-phase, dual channel

    2G 2G IEEE C37.94, 820 nm, 128 kbps, mu lt imode, LED, 1 Channel2H 2H IEEE C37.94, 820 nm, 128 kbps, mu lt imode, LED, 2 Channels72 72 1550 nm, single-mode, LASER, 1 Channel73 73 1550 nm, single-mode, LASER, 2 Channel74 74 Channe l 1 - RS422; Channel 2 - 1550 nm, single -mode, LASER75 75 Channe l 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER76 76 IEEE C37.94, 820 nm, 64 kbps, mult imode, LED, 1 Channel77 77 IEEE C37.94, 820 nm, 64 kbps, mult imode, LED, 2 Channels7A 7A 820 nm, multi-mode, LED, 1 Channel7B 7B 1300 nm, multi-mode, LED, 1 Channel7C 7C 1300 nm, single-mode, ELED, 1 Channel7D 7D 1300 nm, single-mode, LASER, 1 Channel7E 7E Channel 1 - G.703; Channel 2 - 820 nm, multi-mode7F 7F Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode7G 7G Channe l 1 - G.703; Channe l 2 - 1300 nm, s ing le-mode ELED7H 7H 820 nm, multi-mode, LED, 2 Channels7I 7I 1300 nm, multi-mode, LED, 2 Channels7J 7J 1300 nm, single-mode, ELED, 2 Channels7K 7K 1300 nm, single-mode, LASER, 2 Channels7L 7L Channe l 1 - RS422; Channel 2 - 820 nm, mu lt i-mode, LED7M 7M Channe l 1 - RS422; Channel 2 - 1300 nm, mul ti -mode, LED7N 7N Channe l 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED7P 7P Channe l 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER7Q 7Q Channe l 1 - G.703; Channe l 2 - 1300 nm, s ing le-mode LASER7R 7R G.703, 1 Channel7S 7S G.703, 2 Channels7T 7T RS422, 1 Channel7W 7W RS422, 2 Channels

  • 8/13/2019 Order Codes

    4/6

    2-6 F35 Multiple Feeder Protection System GE Multilin

    2.1 INTRODUCTION 2 PRODUCT DESCRIPTION

    2

    The order codes for the reduced size vertical mount units with the process bus module are shown below.

    2.1.3 REPLACEMENT MODULES

    Replacement modules can be ordered separately as shown below. When ordering a replacement CPU module or face-plate, please provide the serial number of your existing unit.

    Not all replacement modules may be applicable to the F35 relay. Only the modules specified in the order codes areavailable as replacement modules.

    Replacement module codes are subject to change without notice. Refer to the GE Multilin ordering page at http://www.GEindustrial.com/multilin/order.htm for the latest details concerning F35 ordering options.

    Table 26: F35 ORDER CODES (REDUCED SIZE VERTICAL UNITS WITH PROCESS BUS)F35 - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)

    BASE UNIT F35 | | | | | | | | | Base UnitCPU E | | | | | | | | RS485 and RS485

    G | | | | | | | | RS485 and multi-mode ST 10Base-FH | | | | | | | | RS485 and multi-mode ST redundant 10Base-FJ | | | | | | | | RS485 and multi-mode ST 100Base-FXK | | | | | | | | RS485 and multi-mode ST redundant 100Base-FXL | | | | | | | | RS485 and single mode SC 100Base-FX

    M | | | | | | | | RS485 and single mode SC redundant 100Base-FXN | | | | | | | | RS485 and 10/100Base-TP | | | | | | | | RS485 and single mode ST 100Base-FXR | | | | | | | | RS485 and single mode ST redundant 100Base-FX

    SOFTWARE 00 | | | | | | | No Software Options01 | | | | | | | Ethernet Global Data (EGD); not available for Type E CPUs03 | | | | | | | IEC 61850; not available for Type E CPUs04 | | | | | | | Ethernet Global Data (EGD) and IEC 61850; not available for Type E CPUs

    MOUNT/COATING V | | | | | | Vertical (3/4 rack)B | | | | | | Vertical (3/4 rack) with harsh environmental coating

    FACEPLATE/ DISPLAY C | | | | | English displayD | | | | | French displayR | | | | | Russian displayA | | | | | Chinese displayK | | | | | Enhanced front panel with English displayM | | | | | Enhanced front panel with French displayQ | | | | | Enhanced front panel with Russian displayU | | | | | Enhanced front panel with Chinese displayL | | | | | Enhanced front panel with English display and user-programmable pushbuttonsN | | | | | Enhanced front panel with French display and user-programmable pushbuttonsT | | | | | Enhanced front panel with Russian display and user-programmable pushbuttonsV | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons

    POWER SUPPLY H | | | | 125 / 250 V AC/DC power supplyL | | | | 24 to 48 V (DC only) power supply

    CT/VT MODULES | 81 | | Eight-port digital process bus moduleDIGITAL INPUTS/OUTPUTS XX XX XX No Module

    4A 4 Solid-State (no monitoring) MOSFET outputs4B 4 Solid-State (voltage with optional current) MOSFET outputs4C 4 Solid-State (current with optional voltage) MOSFET outputs4D 16 digital inputs with Auto-Burnishing

    4L 14 Form-A (no monitoring) Latching outputs67 8 Form-A (no monitoring) outputs6A 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs6B 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs6C 8 Form-C outputs6D 16 digital inputs6E 4 Form-C outputs, 8 digital inputs6F 8 Fast Form-C outputs6G 4 Form-A (voltage with optional current) outputs, 8 digital inputs6H 6 Form-A (voltage with optional current) outputs, 4 digital inputs6K 4 Form-C and 4 Fast Form-C outputs6L 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs6M 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs6N 4 Form-A (current with optional voltage) outputs, 8 digital inputs6P 6 Form-A (current with optional voltage) outputs, 4 digital inputs6R 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs6S 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs6T 4 Form-A (no monitoring) outputs, 8 digital inputs6U 6 Form-A (no monitoring) outputs, 4 digital inputs6V 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs

    INTER-RELAY

    COMMUNICATIONS

    (select a maximum of 1 per unit)

    For the last module, slot P is used for digital and transducer

    input/output modules; slot R is used for inter-relay

    communications modules.

    2A C37.94SM, 1300nm single-mode, ELED, 1 channel single-mode2B C37.94SM, 1300nm single-mode, ELED, 2 channel single-mode2E Bi-phase, single channel2F Bi-phase, dual channel2G IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel2H IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels72 1550 nm, single-mode, LASER, 1 Channel73 1550 nm, single-mode, LASER, 2 Channel74 Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER75 Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels7A 820 nm, multi-mode, LED, 1 Channel7B 1300 nm, multi-mode, LED, 1 Channel7C 1300 nm, single-mode, ELED, 1 Channel7D 1300 nm, single-mode, LASER, 1 Channel7E Channel 1 - G.703; Channel 2 - 820 nm, multi-mode7F Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED7H 820 nm, multi-mode, LED, 2 Channels7I 1300 nm, multi-mode, LED, 2 Channels7J 1300 nm, single-mode, ELED, 2 Channels7K 1300 nm, single-mode, LASER, 2 Channels7L Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED7M Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER7R G.703, 1 Channel7S G.703, 2 Channels7T RS422, 1 Channel7W RS422, 2 Channels

    NOTE

    NOTE

  • 8/13/2019 Order Codes

    5/6

    GE Multilin F35 Multiple Feeder Protection System 2-7

    2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

    The replacement module order codes for the horizontal mount units are shown below.

    Table 27: ORDER CODES FOR REPLACEMENT MODULES, HORIZONTAL UNITSUR - ** - *

    POWER SUPPLY

    (redundant supply only available in horizontal units;

    must be same type as main supply)

    | 1H | 125 / 250 V AC/DC| 1L | 24 to 48 V (DC only)| RH | redundant 125 / 250 V AC/DC| RH | redundant 24 to 48 V (DC only)

    CPU | 9E | RS485 and RS485 (Modbus RTU, DNP 3.0)| 9G | RS485 and 10Base-F (Ethernet , Mo dbus TCP/IP, DNP 3.0)| 9H | RS485 and Redundant 10Base-F (Ethernet , Modbus TCP/IP, DNP 3.0)| 9J | RS485 and multi -mode ST 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)| 9K | RS485 and multi -mode ST redundant 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)| 9L | RS485 and single mode SC 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)| 9M | RS485 and single mode SC redundant 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)| 9N | RS485 and 10 /100Base-T (Etherne t, Modbus TCP/IP, DNP 3 .0)| 9P | RS485 and single mode ST 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)| 9R | RS485 and single mode ST redundant 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)| 9S | RS485 and six-port managed Ethernet switch

    FACEPLATE/DISPLAY | 3C | Horizontal faceplate wit h keypad and Engli sh display| 3D | Horizontal faceplate wit h keypad and French display| 3R | Horizontal faceplate wit h keypad and Russian display| 3A | Horizontal faceplate wit h keypad and Chinese display| 3P | Horizontal faceplate wi th keypad, user-programmable pushbuttons, and Engl ish display| 3G | Horizontal faceplate wi th keypad, user-programmable pushbuttons, and French display| 3S | Horizontal faceplate wi th keypad, user-programmable pushbuttons, and Russian display| 3B | Horizontal faceplate wi th keypad, user-programmable pushbuttons, and Chinese display| 3K | Enhanced front panel with English display| 3M | Enhanced front panel with French display| 3Q | Enhanced front panel with Russian display| 3U | Enhanced front panel with Chinese display| 3L | Enhanced front panel with English display and user-programmable pushbuttons| 3N | Enhanced front panel with French display and user-programmable pushbuttons| 3T | Enhanced front panel with Russian display and user-programmable pushbuttons| 3V | Enhanced front panel with Chinese display and user-programmable pushbuttons

    DIGITAL INPUTS AND OUTPUTS | 4A | 4 Solid-State (no monitoring) MOSFET outputs| 4B | 4 Sol id-State (vo ltage wi th op tiona l current) MOSFET outpu ts| 4C | 4 Sol id-State (curren t with opt iona l vol tage) MOSFET outputs| 4D | 16 digital inputs with Auto-Burnishing| 4L | 14 Form-A (no monitoring) Latching outputs| 67 | 8 Form-A (no monitoring) outputs| 6A | 2 Form-A (vol tage wi th optional current) and 2 Form-C outputs, 8 digital inputs| 6B | 2 Form-A (vol tage wi th optional current) and 4 Form-C outputs, 4 digital inputs

    | 6C | 8 Form-C outputs| 6D | 16 digital inputs| 6E | 4 Form-C outputs, 8 digital inputs| 6F | 8 Fast Form-C outputs| 6G | 4 Form-A (vo ltage wi th op tional curren t) ou tpu ts , 8 dig ital inpu ts| 6H | 6 Form-A (vo ltage wi th op tional curren t) ou tpu ts , 4 dig ital inpu ts| 6K | 4 Form-C and 4 Fast Form-C outputs| 6L | 2 Form-A (current wi th optional voltage) and 2 Form-C outputs, 8 digital inputs| 6M | 2 Form-A (current wi th optional voltage) and 4 Form-C outputs, 4 digital inputs| 6N | 4 Form-A (curren t wi th opt iona l vo ltage) ou tputs, 8 digi tal inputs| 6P | 6 Form-A (curren t wi th opt iona l vo ltage) ou tpu ts , 4 dig ital inputs| 6R | 2 Form-A (no mon itor ing) and 2 Form-C outputs, 8 d ig ital inpu ts| 6S | 2 Form-A (no moni tor ing) and 4 Form-C outputs, 4 d ig ital inpu ts| 6T | 4 Form-A (no monit or ing) outputs, 8 digital inputs| 6U | 6 Form-A (no monit or ing) outputs, 4 digital inputs| 6V | 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs

    CT/VT

    MODULES

    (NOT AVAILABLE FOR THE C30)

    | 8F | Standard 4CT/4VT| 8G | Sensitive Ground 4CT/4VT| 8H | Standard 8CT| 8J | Sensitive Ground 8CT| 8L | Standard 4CT/4VT with enhanced diagnostics| 8M | Sensit ive Ground 4CT/4VT wit h enhanced diagnost ics| 8N | Standard 8CT with enhanced diagnostics| 8R | Sensit ive Ground 8CT with enhanced diagnost ics

    INTER-RELAY COMMUNICATIONS | 2A | C37.94SM, 1300nm single-mode, ELED, 1 channel s ing le -mode| 2B | C37.94SM, 1300nm single-mode, ELED, 2 channel s ing le -mode| 2E | Bi-phase, single channel| 2F | Bi-phase, dual channel| 2G | IEEE C37.94, 820 nm, 128 kbps, mult imode, LED, 1 Channel| 2H | IEEE C37.94, 820 nm, 128 kbps, mult imode, LED, 2 Channels| 2S | Six-port managed Ethernet switch with high voltage power supply (110 to 250 V DC / 100 to 240 V AC)

    | 2T | Six-port managed Ethernet swi tch with low vol tage power supply (48 V DC)| 72 | 1550 nm, single-mode, LASER, 1 Channel| 73 | 1550 nm, single-mode, LASER, 2 Channel| 74 | Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER| 75 | Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER| 76 | IEEE C37.94, 820 nm, multimode, LED, 1 Channel| 77 | IEEE C37.94, 820 nm, multimode, LED, 2 Channels| 7A | 820 nm, multi-mode, LED, 1 Channel| 7B | 1300 nm, multi-mode, LED, 1 Channel| 7C | 1300 nm, single-mode, ELED, 1 Channel| 7D | 1300 nm, single-mode, LASER, 1 Channel| 7E | Channel 1 - G.703; Channel 2 - 820 nm, multi-mode| 7F | Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode| 7G | Channel 1 - G.703; Channel 2 - 1300 nm, single-mod e ELED| 7H | 820 nm, multi-mode, LED, 2 Channels| 7I | 1300 nm, multi-mode, LED, 2 Channels| 7J | 1300 nm, single-mode, ELED, 2 Channels| 7K | 1300 nm, single-mode, LASER, 2 Channels| 7L | Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED| 7M | Channel 1 - RS422; Channel 2 - 1300 nm, mult i-mode, LED| 7N | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED| 7P | Channe l 1 - RS422; Channel 2 - 1300 nm, s ingle-mode, LASER| 7Q | Channe l 1 - G.703; Channel 2 - 1300 nm, s ingle-mode LASER| 7R | G.703, 1 Channel| 7S | G.703, 2 Channels| 7T | RS422, 1 Channel| 7W | RS422, 2 Channels

    TRANSDUCER

    INPUTS/OUTPUTS

    | 5A | 4 dcmA inputs, 4 dcmA outpu ts (onl y one 5A module i s a llowed)| 5C | 8 RTD inputs| 5D | 4 RTD inputs, 4 dcmA outpu ts (on ly one 5D module is a llowed)| 5E | 4 dcmA inputs, 4 RTD inputs

    | 5F | 8 dcmA inputs

  • 8/13/2019 Order Codes

    6/6

    2-8 F35 Multiple Feeder Protection System GE Multilin

    2.1 INTRODUCTION 2 PRODUCT DESCRIPTION

    2

    The replacement module order codes for the reduced-size vertical mount units are shown below.

    Table 28: ORDER CODES FOR REPLACEMENT MODULES, VERTICAL UNITSUR - ** - *

    POWER SUPPLY | 1H | 125 / 250 V AC/DC| 1L | 24 to 48 V (DC only)

    CPU | 9E | RS485 and RS485 (Modbus RTU, DNP 3.0)| 9G | RS485 and 10Base-F (Ethernet, Modbus TCP/ IP, DNP 3.0)| 9H | RS485 and Redundant 10Base-F (Etherne t, Modbus TCP/IP, DNP 3.0)| 9J | RS485 and multi -mode ST 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)| 9K | RS485 and multi -mode ST redundant 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)| 9L | RS485 and single mode SC 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)| 9M | RS485 and single mode SC redundant 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)| 9N | RS485 and 10/100Base-T (Ethernet , Modbus TCP/IP, DNP 3.0)| 9P | RS485 and single mode ST 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)| 9R | RS485 and single mode ST redundant 100Base-FX (Ethernet, Modbus TCP/IP, DNP 3.0)

    FACEPLATE/DISPLAY | 3F | Vert ical f aceplate wit h keypad and English display| 3D | Vert ical f aceplate wit h keypad and French d isplay| 3R | Vert ical faceplate wit h keypad and Russian display| 3K | Vert ical f aceplate wit h keypad and Chinese display| 3K | Enhanced front panel with English display| 3M | Enhanced front panel with French display| 3Q | Enhanced front panel with Russian display| 3U | Enhanced front panel with Chinese display| 3L | Enhanced front panel wi th Engl ish display and user-programmable pushbuttons| 3N | Enhanced front panel with French display and user-programmable pushbuttons| 3T | Enhanced front panel wi th Russian display and user-programmable pushbuttons| 3V | Enhanced front panel wi th Chinese display and user-programmable pushbuttons

    DIGITAL

    INPUTS/OUTPUTS

    | 4A | 4 Solid-State (no monitoring) MOSFET outputs| 4B | 4 So lid -State (vo ltage with opt ional curren t) MOSFET outpu ts| 4C | 4 So li d-State (current wi th opt ional vo ltage) MOSFET outputs| 4D | 16 digital inputs with Auto-Burnishing| 4L | 14 Form-A (no monitoring) Latching outputs| 67 | 8 Form-A (no monitoring) outputs| 6A | 2 Form-A (vol tage wi th optional current) and 2 Form-C outputs, 8 digital inputs| 6B | 2 Form-A (vol tage wi th optional current) and 4 Form-C outputs, 4 digital inputs| 6C | 8 Form-C outputs| 6D | 16 digital inputs| 6E | 4 Form-C outputs, 8 digital inputs| 6F | 8 Fast Form-C outputs| 6G | 4 Form-A (vol tage with opt iona l current) outputs, 8 digi tal inputs| 6H | 6 Form-A (vol tage with opt iona l current) outputs, 4 digi tal inputs| 6K | 4 Form-C and 4 Fast Form-C outputs

    | 6L | 2 Form-A (current wi th optional voltage) and 2 Form-C outputs, 8 digital inputs| 6M | 2 Form-A (current wi th optional voltage) and 4 Form-C outputs, 4 digital inputs| 6N | 4 Form-A (current with opt ional vo ltage) outpu ts, 8 digital inpu ts| 6P | 6 Form-A (current with opt ional vo ltage) outpu ts, 4 digital inpu ts| 6R | 2 Form-A (no moni to ri ng) and 2 Form-C ou tputs, 8 digi tal inputs| 6S | 2 Form-A (no moni to ri ng) and 4 Form-C ou tputs, 4 digi tal inputs| 6T | 4 Form-A (no monitoring) outputs, 8 digital inputs| 6U | 6 Form-A (no monitoring) outputs, 4 digital inputs| 6V | 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs

    CT/VT

    MODULES

    (NOT AVAILABLE FOR THE C30)

    | 8F | Standard 4CT/4VT| 8G | Sensitive Ground 4CT/4VT| 8H | Standard 8CT| 8J | Sensitive Ground 8CT| 8L | Standard 4CT/4VT with enhanced diagnostics| 8M | Sensitive Ground 4CT/4VT with enhanced diagnostics| 8N | Standard 8CT with enhanced diagnostics| 8R | Sensitive Ground 8CT wit h enhanced diagnostics

    INTER-RELAY COMMUNICATIONS | 2A | C37.94SM, 1300nm s ingle -mode, ELED, 1 channe l s ingle -mode| 2B | C37.94SM, 1300nm s ingle -mode, ELED, 2 channe l s ingle -mode| 2E | Bi-phase, single channel| 2F | Bi-phase, dual channel| 2G | IEEE C37.94 , 820 nm, 128 kbps, multimode, LED, 1 Channel| 2H | IEEE C37.94 , 820 nm, 128 kbps, mul timode, LED, 2 Channels| 72 | 1550 nm, single-mode, LASER, 1 Channel| 73 | 1550 nm, single-mode, LASER, 2 Channel| 74 | Chann el 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER| 75 | Chann el 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER| 76 | IEEE C37.94, 820 nm, 64 kbps, mult imode, LED, 1 Channel| 77 | IEEE C37.94, 820 nm, 64 kbps, mult imode, LED, 2 Channels| 7A | 820 nm, multi-mode, LED, 1 Channel| 7B | 1300 nm, multi-mode, LED, 1 Channel

    | 7C | 1300 nm, single-mode, ELED, 1 Channel| 7D | 1300 nm, single-mode, LASER, 1 Channel| 7E | Channel 1 - G.703; Channel 2 - 820 nm, multi-mode| 7F | Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode| 7G | Chann el 1 - G.703; Channel 2 - 1300 nm, single-mode ELED| 7H | 820 nm, multi-mode, LED, 2 Channels| 7I | 1300 nm, multi-mode, LED, 2 Channels| 7J | 1300 nm, single-mode, ELED, 2 Channels| 7K | 1300 nm, single-mode, LASER, 2 Channels| 7L | Chann el 1 - RS422; Channel 2 - 820 nm, mult i-mo de, LED| 7M | Chann el 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED| 7N | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED| 7P | Chann el 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER| 7Q | Chann el 1 - G.703; Channel 2 - 1300 nm, single-mode LASER| 7R | G.703, 1 Channel| 7S | G.703, 2 Channels| 7T | RS422, 1 Channel| 7W | RS422, 2 Channels

    TRANSDUCER

    INPUTS/OUTPUTS

    | 5A | 4 dcmA inputs, 4 dcmA outpu ts (on ly one 5A module is al lowed)| 5C | 8 RTD inputs| 5D | 4 RTD inputs , 4 dcmA outputs (onl y one 5D modu le i s a ll owed)| 5E | 4 dcmA inputs, 4 RTD inputs| 5F | 8 dcmA inputs