View
214
Download
0
Tags:
Embed Size (px)
Citation preview
Naser Tarhuni 2
Outline
Introduction First Generation Optical Networks
Fiber Distributed Data Interface (FDDI) Synchronous Optical Network/Synchronous Digital
Hierarchy (SONET/SDH) Second Generation Optical Networks
Wavelength Division Multiplexing (WDM) Optical Networking Components Wavelength Routing Networks
Naser Tarhuni 4
Introduction(1) Advantages of Optical Transmission
Large bandwidth permits high data transmission, which also supports the aggregation of voice, video, and data
Technological improvements are occurring rapidly, often permitting increased capacity over existing optical fiber
Immunity to electromagnetic interference reduces bit error rate and eliminates the need for shielding within or outside a building
Glass fiber has low attenuation, which permits extended cable transmission distance
Light as a transmission medium provides the ability for the use of optical fiber in dangerous environments
Optical fiber is difficult to tap, thus providing a higher degree of security than possible with copper wire
Light weight and small diameter of fiber permit high capacity through existing conduits
Naser Tarhuni 5
Introduction(2) Disadvantages of Optical Transmission
Cable splicing: Welding or fusing: you must clean each fiber end, then
align and carefully fuse the ends using an electric arc. Time consuming Least amount of signal loss between joined elements.
Gluing Bonding material that matches the refractive index of the core of
the fiber. Time consuming Higher loss of signal power than fusing.
mechanical connectors Considerably facilitate the joining of fibers, More signal loss than do the other two methods Can reduce the span of the fiber to a smaller distance.
Naser Tarhuni 6
Introduction(3)
Fiber cost: On a (bit/s)/km basis, the fiber cost will always be
less than that for copper cable.
Some organizations may require only a fraction of the capacity of the optical fiber. It is often difficult to justify fiber to the desktop and similar
applications where the cost of copper cable may be half or less than the cost of fiber.
Naser Tarhuni 9
Fiber Distributed Data Interface (FDDI)
Dates back to the early 1980s FDDI uses token-passing scheme Uses two fiber pairs, each operating at 100 Mbits/s. Data rates approaching 90% of its 100 MB/s
operating rate FDDI was, and in some locations still is, commonly
used at the Internet Service Provider (ISP) peering points that provide interconnections between ISPs.
Relatively expensive
Naser Tarhuni 10
FDDI Position in the OSI Reference Model
FDDI is defined as the two bottom layers of the seven-layer OSI reference model
It provides a transport facility for higher-level protocols such as TCP/IP
Physical layer is subdivided into: physical-medium-dependent (PMD)
sublayer defines the details of the fiber-optic cable used
the physical (PHY) layer specifies encoding/decoding and clocking operation
Naser Tarhuni 11
FDDI 4B/5B Coding The selection of the 4B/5B coding was based on the need to reduce
the signaling level from 200 MHz to a 125-MHz rate (cost reduction) Each bit is encoded using non-returnto-zero-inversion (NRZI)
transmission Because 4 bits are encoded into 5 bits, this means there are 16, 4-
bit patterns. Those patterns were selected to ensure that a transition is present
at least twice for each 5-bit code. DC balance: important for thresholding at receiver For some input data sequences the worst case DC unbalance is 10%
Because 5-bit codes are used, the remaining symbols provide special meanings or represent invalid symbols.
Special symbols I symbol is used to exchange handshaking between
neighboring stations, J and K symbols are used to form the Start Delimiter for a
packet, which functions as an alert to a receiver that a packet is arriving.
Naser Tarhuni 12
FDDI Fiber Specifications
OPTICAL FIBER SUPPORT FDDI can support 62.5/125-, 50/125-, and 100/140-µm multimode fiber sizes.
Maximum distance 2 Km. FDDI also supports the use of single-mode fiber,
Long-distance transmission (up to 40 Km) FDDI single-mode fiber is commonly specified as 8/125, 9/125, and 10/125.
OPTICAL TRANSMITTER 850, 1300, and 1550 nm 850 and 1300 nm for multimode fiber 1300 and 1500 nm for single-mode fiber For single-mode fiber laser diodes must be used
ATTENUATION For multimode fiber
PMD standard specifies a power budget of 11.0 dB Maximum cable attenuation is 1.5 dB/km at 1300 nm.
single-mode fiber power budget extends from 10 to 32 dB
Core/Cladding
this means that up to 11 dB of the optical signal can be lost.
Naser Tarhuni 13
FDDI Ring Structure
FDDI backbone consists of two separate fiber-optic rings, primary ring: active secondary ring: “on hold,”
Station Types Class A:dual-attachment stations, Class B: single-attachment station.
Naser Tarhuni 14
SONET/SDH(1)
Current transmission and multiplexing standard for high speed signals North America: Synchronous Optical Network (SONET) Europe, Japan and rest of the world: Synchronous Digital Hierarchy
(SDH) Prior to SONET and SDH: Plesiochronous Digital Hierarchy (PDH)
4KHz sampled at 8KHz quantized at 8 bits per sample 64kb/s
LevelNorth America [Mb/s]Europe [Mb/s]Japan [Mb/s]
0DS00.0640.0640.064
1DS1/T11.544E12.0481.544
2DS2/T26.312E28.4486.312
3DS3/T344.736E334.36832.064
4139.264E4139.26497.728
Transmission rates for PDH
Naser Tarhuni 15
SONET/SDH(2) PDH versus SONET/SDH
Multiplexing PDH: Difficult to pick low bit rate stream from high bit rate stream In PDH, clocks of lower bit streams are not perfectly synchronous
Higher rates are not integral multiples of 64Kb/s Bit stuffing needed Mulltiplexers and Demultiplexers complicated
In SONET/SDH a master clock is usedMUX and DEMUX much easier
Management Unlike PDH, SONET/SDH standards are rich of management and
traffic performance monitoring information Interoperability
SONET/SDH define standard optical interfaces PDH: different vendors define different line coding, optical
interfaces,... Networking
SONET/SDH: Service restoration time is less than 60 ms PDH: restoration time is several seconds to minutes
Naser Tarhuni 16
SONET/SDH(3) SONET/SDH
Lower speed PDH is mapped into synchronous payload envelope (SPE), or synchronous container in SDH
Path overhead bytes are added to the SPE Path overhead unchanged during transmission Allows PDH monitoring end-to-end
SPE+path overhead = virtual tributary VT (container in SDH) VT may be placed at different points within a frame (125 µs) Many small VTs can be multiplexed into a larger VT (see next
slide) The overhead of each VT includes a pointer to smaller VTs
multiplexed into the payload of the larger VT This hierarchical structure simplifies extraction of low speed
stream from high speed stream
Naser Tarhuni 17
SONET/SDH(4)
Smaller VT
Poi
nter
Small VT Small VTSmall VT
Poi
nter
Poi
nter
Poi
nter
Big VT
Hierarchical multiplexing structure employed in SONET and SDH
In SONET: VTs with four sizes VT1.5, VT2, VT3, VT6 that carry 1.5, 2, 3, 6 Mb/s PDH streams VT group = 4 VT1.5s or 3 VT2s or 2 VT3s or a single VT6 Basic SONET SPE (STS-1) = 7 VT groups = 51.84 Mb/s STS-N = N × STS-1 (byte interleaved) STS = Synchronous Transport Signal STM-1 = synchronous Transport Module = 155 MB/s
Naser Tarhuni 18
SONET/SDH(5)
VT1.5 SPE VT1.5
(SPE + path overhead)DS11.544 Mb/s
VT2 SPE VT2
E12.048 Mb/s
VT3 SPE VT3
DS1C3.152 Mb/s
VT6 SPE VT6
DS26.312 Mb/s
VT group
STS-1 SPE
DS344.736 Mb/s
ATM48.384 Mb/s
STS-3c SPE
E4139.264 Mb/s
ATM149.760 Mb/s
STS-1
STS-3c
STS-N
× 4
× 3
× 2
× 1 × 7byte interleaved
× N
× N/3
The mapping of lower-speed PDH streams into VTs in SONET
Locked payload: not possible to demultiplex into lower-speed streams
SONET SignalSDH signal
Bit rate [Mb/s]
STS-151.84
STS-3 (OC-3)STM-1155.52
STS-12 (OC-12)STM-4622.08
STS-24 1244.16
STS-48 (OC-48)STM-162488.32
STS-192 (OC-192)
STM-649953.28
Optical Carrier
Naser Tarhuni 19
SONET/SDH(6)
SONET/SDH network configurations (see next slide) Point-to-point
Node at ends Terminal Multiplexers (TM) Line Terminating Equipment (LTE)
Linear Inserting add/drop multiplexers (ADM) between TM in point-to
point-links. Allows insertion or extraction of smaller traffic at mid-points
Rings ADM with added function of protection: High level of availability Unidirectional path-switched rings (UPSRs) Bidirectional line-switched rings (BLSRs)
Two fibers BLSR/2, four fibers BLSR/4
Naser Tarhuni 20
SONET/SDH(7)
Digital crossconnect (DCS): Manage all transmission
facilities in the central office
UPSR
OC-3/OC-12
ADM
ADMADM
ADM
BLSR/2Or
BLSR/4OC-12/OC-48
ADM
ADMADM
ADM
UPSR
OC-3/OC-12
ADM
ADM
ADM
UPSR
OC-3/OC-12
ADM
ADM
ADM
TM
TM
ADM
ADM
DCS
DCS
BLSR/2Or
BLSR/4OC-12/OC-48
ADM
ADMADM
ADM
Backbone ring
Backbone ring
Access ring
Access ring
Access ring
Linear add/drop
Point to point
Central office
Central office
Naser Tarhuni 21
SONET/SDH(8) Path layer: End-to-end connections Line layer:
Multiplexes a numer of path-layer connection into a single link
Responsible for protection switching Section layer: Links consist of sections
Present at each regenerator
Path layer
Line layer
Section layer
Physical layer
Section layer
Physical layer
Line layer
Section layer
Physical layer
Path layer
Line layer
Section layer
Physical layer
SONET/SDH layers
connection
SONET terminal
Regenerator
SONET ADM
SONET terminal
Naser Tarhuni 22
SONET/SDH(9)SELF-HEALING SONET/SDH RINGS
Causes for a ring to go down: Failure of a fiber link:
Fiber is accidentally cutoff The transmission or receiver equipment on the fiber link fail. SONET/SDH device fails (rare)
Services automatically restored: using the automatic protection switching (APS) protocol. The time to restore the services has to be less than 60 msec.
Link protection: Dedicated 1 + 1,
The two devices are connected with two different fibers.
The SONET/SDH signal is split and simultaneously transmitted over both fibers.
The destination selects the best of the two signals based on their quality.
The working and protection fibers have to be diversely routed
Naser Tarhuni 23
SONET/SDH(10)SELF-HEALING SONET/SDH RINGS
Link protection: 1:1 scheme,
Two diversely routed fibers: a working fiber and a protection fiber.
The signal is transmitted over the working fiber. If this fiber fails, then the source and destination both switch to
the protection fiber. The 1:N scheme
Generalization of the 1:1 scheme, N working fibers are protected by a single protection fiber. Only one working fiber can be protected at any time. Once a working fiber has been repaired, the signal is switched
back, either automatically or manually, from the protection fiber to the working fiber.
Naser Tarhuni 24
SONET/SDH(11)SELF-HEALING SONET/SDH RINGS
Self-healing SONET/SDH ring architectures are distinguished by Number of fibers: A SONET/SDH ring can consist of either two or
four fibers. the working and protection rings are route diverse. Direction of transmission: A SONET/SDH ring can be
unidirectional or bidirectional. Line or path switching: Protection on a SONET/SDH ring can be
at the level of a line or a path. Line is a link between two SONET/SDH devices and might include
regenerators. A path is an end-to-end connection between
the point where the SPE originates and the point where it terminates.
Line switching restores all of the traffic that pass through a failed link
Path switching restores some of the connections that are affected by a link failure.
Naser Tarhuni 25
SONET/SDH(12)SELF-HEALING SONET/SDH RINGS
Two-fiber Unidirectional Path Switched Ring (2F-UPSR) Example: The working ring consists of fibers 1, 2, 3, and 4; the
protection ring consists of fibers 5, 6, 7, and 8. Unidirectional: A transmits to B over fiber 1 (working), and B
transmits to A over fibers 2, 3, and 4 (working).
Protection: path level using 1 + 1
Simple ring architecture: Used as a metro edge ring to interconnect PBXs and access networks to a metro core ring.
Typical transmission speeds are OC-3/STM-1 and OC-12/STM-4. Disadvantage:The maximum amount of traffic it can carry is equal
to the traffic it can carry over a single fiber.
Naser Tarhuni 26
SONET/SDH(13)SELF-HEALING SONET/SDH RINGS
Two-fiber Bidirectional Line Switched Ring (2F-BLSR) Used in metro core rings. Example:
Clockwise transmission (Ring 1): Fibers 1, 2, 3, 4, 5 and 6.
Counter-clockwise transmission (Ring 1): Fibers 7, 8, 9, 10, 11, and 12.
Rings 1 and 2 carry working and protection traffic.
Assume: each fiber is OC-12/STM-4. Then, two OC-3/STM-1s are allocated to working traffic and the other two to protection traffic.
Since only two OC-3/STM-1s can be used for working traffic, the maximum capacity that the 2F-BLSR can carry over both Rings 1 and 2 is OC-12/STM-4.
The capacity allocated to protection traffic on either Rings 1 and 2 can be used to carry low priority traffic.
Naser Tarhuni 27
SONET/SDH(14)SELF-HEALING SONET/SDH RINGS
2F-BLSR Bidirectional:
Ring 1 or Ring 2, depending on the route of the shortest path to the destination.
A transmits to B over the working part of fibers 1 and 2 of Ring 1, B transmits to A over the working part of fibers 8 and 7 of Ring 2.
Fiber 2 fails: line switching: Traffic over fiber 2 automatically switched to the
protection part of Ring 2. All of the traffic will be rerouted to ADM 3 over the protection part of
Ring 2 using fibers 7, 12, 11, 10, and 9. From there, the traffic continue on following the original path of the
connection. Consider a connection from A to C (solid line). When fiber 2 fails, the traffic from A will be rerouted (dotted line). At ADM 3, it will be routed back to ADM 4 over fiber 3.
Naser Tarhuni 29
Optical Layers(1)
Physical Layer First generation networks:
Point-to-point, full bandwidth over single wavelength to layers above Second generation networks:
Variable amounts of bandwidth Optical layer: Provide lightpaths to varaity of first-generation optical
layers
ATM layer
SONET/SDH layer ATM layer
Optical layer
ESCON layer
Virtual circuitsVirtual circuitsVirtual circuits
User applications
SONET/SDH connections
Lightpaths
Enterprise Serial Connection
Naser Tarhuni 30
Optical Layers(2)
Optical layer OC (lightpath layer): end-to-end connections Each lightpath traverses a number of links, each link carries multiple wavelengths
(WDM). Optical multiplex section OMS: point-to-point
Consists of several segments
MultiplexSection
connection
WDM node
Amplifier
WDM node
WDM node
OpticalChannel
AmplifierSection
MultiplexSection
OpticalChannel
AmplifierSection
AmplifierSection
MultiplexSection
AmplifierSection
Path
Line
SectionPhysical
MultiplexSection
Channel
AmplifierSection
SO
NE
T/S
DH
laye
r
Opt
ical
laye
r
Example:SONET over optical layer
Naser Tarhuni 31
WDM OPTICAL NETWORKS Considerable increase in traffic became a driving force for WDM
and its evolution into dense WDM (DWDM). WDM refers to the technology of combining multiple wavelengths
onto the same optical fiber. Each wavelength is a different channel. At the transmitting end, there are W independent transmitters. Each
transmitter Tx is a light source, such as a laser, and is independently modulated with a data stream. The output of each transmitter is an optical signal on a unique wavelength λi , i = 1, 2, . . . , W.
WDM: ~200 GHz spacing DWDM: ~50 GHz spacing
Naser Tarhuni 32
Components: Lasers(1)
A laser is a device that produces a very strong and concentrated beam. It consists of an energy source which is applied to a lasing material, a
substance that emits light in all directions and it can be of gas, solid, or semiconducting material.
The light produced by the lasing material is enhanced using a device such as the Fabry-Perot resonator cavity.
This cavity consists of two partially reflecting parallel flat mirrors, known as facets.
These mirrors are used to create an optical feedback which causes the cavity to oscillate with a positive gain that compensates for any optical losses.
Light hits the right facet and part of it leaves the cavity through the right facet and part of it is reflected.
Part of the reflected light is reflected back by the left facet towards the right facet, and again part of it exits through the right-facet and so on.
Naser Tarhuni 33
Components: Lasers(2)
Consider a wavelength for which the cavity length (i.e., the distance between the two mirrors) is an integral multiple of half the wavelength. For such a wavelength, all of the light waves transmitted through the right
facet are in phase. Such a wavelength is called a resonant wavelength of the cavity.
Since there are many resonant wavelengths, the resulting output consists of many wavelengths.
It is desirable that only a single wavelength comes out from the laser. Using a filtering mechanism that selects the desired wavelength. Another cavity can be used after the primary cavity where gain occurs. Using reflective facets in the second cavity, the laser can oscillate only at
those wavelength resonant for both cavities. Tunable lasers
More convenient than making different lasers for specific wavelengths. Several different types of tunable lasers exist, varying from slow tunability
to fast tunability.
Naser Tarhuni 34
Components: 2 × 2 Couplers(1)
The 2 × 2 coupler is a basic device in optical networks, Fused-fiber coupler.
Fabricated by twisting together, melting, and pulling two single-mode fibers so that they get fused together over a uniform section of length.
Known also as directional coupler. The coupled optical power is varied by varying the length of the
coupling region, the size of the reduced radius of the core in the coupling region, and the difference in the radii of the two fibers in the coupling region.
There is always some power loss when the light goes through the coupler.
Naser Tarhuni 35
Components: 2 × 2 Couplers(2) Waveguide coupler
A waveguide is a medium that confines and guides a propagating electromagnetic wave. A waveguide coupler has two identical parallel guides in the coupling region.
As in the fused-fiber coupler, part of the light going down one guide is coupled onto the other guide.
The degree of interaction between the two guides can be varied through the width of the guide, the gap between the two guides, and the refractive index between the two guides.
3-dB coupler: Power is divided evenly between output ports
Splitter: One input, two outputs Combiner: Two inputs, one output
Naser Tarhuni 36
Components: 2 × 2 Couplers(3) Star coupler: Combines power from N inputs and splitts evenly to N
outputs Fused-fiber method, limited to small N
Combining 3-dB couplers in Banyan network Number 3-dB of couplers = (N/2) log2 N Each input is associated with a different wavelength. The star coupler combines
all of the wavelengths together and then evenly distributes them on all of the output ports.
It can also be used as 1-to-N splitter (demultiplexer) or an N-to-1 combiner (multiplexer).
Naser Tarhuni 37
Components: Optical Amplifiers(1) Optical amplification is used to restore the strength
of the signal. In a WDM link we can use:
power amplifiers, in-line amplifiers, preamplifiers.
Prior to optical amplifiers, the optical signal was regenerated by first converting it into an electrical signal, then apply 1R or 2R or 3R regeneration, and then converting the regenerated signal back into the optical domain. 1R, the electrical signal is simply re-amplified, in 2R, the signal is re-amplified and re-shaped, and in 3R, the signal is reamplified, re-shaped, and re-timed.
Naser Tarhuni 38
Components: Optical Amplifiers(2)
1R can be done optically without knowledge of the bit rate and the framing format Currently, re-shaping and re-timing cannot be done in the
optical domain. Optical 1R can be applied simultaneously to the
combined signal of all of the wavelengths in a WDM link.
Types of optical amplifiers, Erbium-doped fiber amplifier (EDFA), (see next slide). Semiconductor optical amplifier (SOA) Raman amplifier.
Naser Tarhuni 39
Components: Erbium-doped fiber amplifier
A laser that operates at 980 nm or 1480 nm is emitted into the fiber and is combined through a coupler with the signal in the 1550 nm window that needs to be amplified.
An isolator is used to prevent reflections into the amplifier. Two-stage EDFA shown is much more common.
In the first stage, a co-directional laser pumps into the coupler in the same direction as the signal to be amplified, and
in the second stage, a counter-directional laser pumps into the coupler in the opposite direction of the signal to be amplified.
Counter-directional pumping gives higher gain, Co-directional pumping gives better noise performance.
Two-stage EDFA
Naser Tarhuni 40
Components: Optical Cross-connects(1) An optical cross-connect (OXC) is an N × N optical switch,.
it can switch the optical signal on incoming wavelength λi of input fiber k to the outgoing wavelength λi of output fiber m.
If it is equipped with converters, it can also switch the optical signal of the incoming wavelength λi of input fiber k to another outgoing wavelength λj of the output fiber m.
OXC can also be used as an optical add/drop multiplexer (OADM). In the example shown, wavelengths λ1 and λW of input fiber 1 are directed to
output fiber N. Likewise, wavelengths λ1 and λW of input fiber N are directed to output fiber 1.
An OXC should have: Low switching time (burst switching appl.) Low insertion loss: power lost because of
the presence of the switch in the optical network.
Low crosstalk: the ratio of the power at an output from an input to the power from all other inputs.
Low polarization-dependent loss.
Naser Tarhuni 41
Components: Optical Cross-connects(2) Technologies for building a switch fabric of an OXC,
Multi-stage interconnection networks of 2 × 2 switches (directional couplers) electro-optic switch, thermo-optic switch, and the Mach-
Zehnder interferometer. Digital micro electronic mechanical systems (MEMS), Semiconductor optical amplifiers (SOA).
Micro electronic mechanical systems (MEMS): dimension from a few hundred microns to millimeters. fabricated on silicon substrates using standard
semiconductor processing techniques.
robust, long-lived, and inexpensive to produce.
Naser Tarhuni 42
Components: Optical Cross-connects(3)
The 2D MEMS is a square array of N × N micro-mirrors (actuator and a mirror) arranged in a crossbar. Each row of micro-mirrors = an input port, (single wavelength) Each column of micro-mirrors = output port. A micro-mirror can be either in the down or up position.
For a wavelength on input port i to be switched to output port j , all micro-mirrors along the ith row, from
column 1 to port j − 1 have to be in the down position,
the micro-mirror in the (i, j ) position has to be up,
the micro-mirrors on the jth column from rows i + 1 to N have to be in the down position.
Naser Tarhuni 43
Components: Optical Add-Drop Multiplexer OADM can drop a number of incoming wavelengths and insert new
optical signals on these wavelengths. The remaining wavelengths of the WDM link are allowed to pass through.
The wavelengths that it adds/drops can be either statically or dynamically configured.
OADM can be easily implemented using the 2D MEMS architecture.
OADM Logical diagram 2D MEMS OADM
Naser Tarhuni 44
Wavelength Routing Optical Networks
Lightpaths Circuit-switched network. This connection is a circuit-switching connection and is established by
using a wavelength on each hop along the connection’s path. Exmaple
Lightpaths from router A to C over OXCs 1 and 2; from B to D over OXCs 1 and 3; and from C to D over OXCs 2 and 3.
OXC 3 contains wavelength converter
Assumed single fiber carrying W wavelengths,
Unidirectional transmission.