OPERATION & SET-UP MANUAL - tracsystemshelpdesk.tracsystems.com/export/7508_ITC_Coin-OP 5400_USA_rev1_7.pdf · Using a Paper Clutch ... Coin Return Coin Slot COM1 Lock COM2 USB Bill

Copyright © 2008 ITC SYSTEMS. All rights reserved. No part of this publication may be reproduced, distributed, copied, or recorded in any form or by any means without the express written permission of ITC SYSTEMS. Notice: ITC SYSTEMS shall not be held liable for errors or omissions contained in this manual nor for any damages in connection with the use of this material or content.

OPERATION & SET-UP MANUAL

5400 Series Coin Operated Controllers

USA Market

ITC SYSTEMS 705 Progress Ave.

Building 63 Toronto ON Canada

M1H 2X1

800 Fee Fee Rd. St Louis MO USA

63043

Document:

5400_USA_rev1_7.doc Firmware Release 1.21 and Higher

May, 2008 P 2 of 82 Z:\CABINETS\Service\MANUALS\CURRENT\5400\5400_USA_rev1_7.doc rev 1.7

Table of Contents TABLE OF CONTENTS ........................................................................................................................................... 2

SALES AND SERVICE ............................................................................................................................................. 7

INTRODUCTION ...................................................................................................................................................... 8

IDENTIFYING THE COMPONENTS ............................................................................................................................... 8 OPERATING MODE DISPLAYS ................................................................................................................................... 9

PROGRAMMING AND SET-UP ........................................................................................................................... 11

BOARD LAYOUT ..................................................................................................................................................... 12 USING THE KEYPAD FOR PROGRAMMING ............................................................................................................... 12 SERVICE MENUS WITH BYPASS KEY OFF ............................................................................................................... 13 COIN TUBE REPORTING .......................................................................................................................................... 14

Changing Coin Tube Inventory ......................................................................................................................... 14 RE-SETTABLE METERS REPORTING ........................................................................................................................ 14 CLEAR RE-SETTABLE METERS ................................................................................................................................ 15 GRAND METERS REPORTING .................................................................................................................................. 15 LOADING THE COIN TUBES ...................................................................................................................................... 16 TOPPING OFF THE COIN TUBES ................................................................................................................................ 16 METERS REPORTS ............................................................................................................................................. 17

Re-settable Meters ............................................................................................................................................ 17 Grand Total Meters .......................................................................................................................................... 18

BYPASS/PROGRAMMING MODE ...................................................................................................................... 19

COIN TUBE (INVENTORY) MODE ............................................................................................................................ 23

SYSTEM SETUP MODE ........................................................................................................................................ 23

Set Date ....................................................................................................................................................... 23 Set Time ....................................................................................................................................................... 23 Unit ID .......................................................................................................................................................... 23 Copier Type ................................................................................................................................................ 24 Enable Printing ....................................................................................................................................... 24 Enable Fax .................................................................................................................................................. 24 Language ....................................................................................................................................................... 24

PERIPHERALS SETUP MODE ............................................................................................................................ 25

Card Reader ................................................................................................................................................ 25 Bill Installed ......................................................................................................................................... 25

BILLS SETUP MODE ............................................................................................................................................. 26

Accept 1.00 ................................................................................................................................................ 26 Accept 5.00 ................................................................................................................................................ 26 Accept 10.00 .............................................................................................................................................. 26 Accept 20.00 .............................................................................................................................................. 26 Accept 50.00 .............................................................................................................................................. 26 Accept 100.00 ........................................................................................................................................... 26

COIN CHANGER SETUP MODE ......................................................................................................................... 27

Return Escrow ........................................................................................................................................... 27 Max Escrow Value .................................................................................................................................... 27 Min Escrow Value .................................................................................................................................... 27 ESCROW<P2=CANCEL .................................................................................................................................... 27


CARD READER SETUP MODE ........................................................................................................................... 28

Accept Types .............................................................................................................................................. 28 Card Format ................................................................................................................................................ 28 Accept ICS/XCP ......................................................................................................................................... 28 Convert to ACDI ....................................................................................................................................... 28 Accept Danyl .............................................................................................................................................. 28

STX AND ROM DEFINITION ................................................................................................................................... 29 Reader STX .................................................................................................................................................. 29 Reader ROM .................................................................................................................................................. 29 Site 1 ............................................................................................................................................................ 29 Site 2 ............................................................................................................................................................ 29 Site 3 ............................................................................................................................................................ 30 Display tenths/c .................................................................................................................................... 30 Max Value Cash ......................................................................................................................................... 30 Max Value Units ....................................................................................................................................... 30 Add Value w/Coin .................................................................................................................................... 30 Add Value w/Bill .................................................................................................................................... 30 Add Val to units .................................................................................................................................... 30 Cents per unit ......................................................................................................................................... 30 dSite 4 (5-10) ......................................................................................................................................... 31 Sideboard Type ......................................................................................................................................... 31

CASH PRICES SETUP MODE .............................................................................................................................. 32

COPIER TYPE 2: PRICE SETTINGS ............................................................................................................................ 32 Line 1 Cash Cost .................................................................................................................................... 32 Line 2 Cash Cost .................................................................................................................................... 32

COPIER TYPE MINOLTA 1: PRICE SETTINGS ............................................................................................................ 32 Small BW Cash ........................................................................................................................................... 32 Med. BW Cash .............................................................................................................................................. 33 Lrg. BW Cash .............................................................................................................................................. 33 Small BW 2side ......................................................................................................................................... 33 Med. BW 2side ........................................................................................................................................... 33 Lrg. BW 2side ........................................................................................................................................... 33 Small CLR Cash ......................................................................................................................................... 33 Med. CLR Cash ........................................................................................................................................... 33 Lrg. CLR Cash ........................................................................................................................................... 33 Small CLR 2side ....................................................................................................................................... 33 Med. CLR 2side ......................................................................................................................................... 34 Lrg. CLR 2side ......................................................................................................................................... 34

COPIER TYPE MINOLTA 2: PRICE SETTINGS ............................................................................................................ 34 Fax Page Cash ........................................................................................................................................... 34 Fax Connect fee ....................................................................................................................................... 34 Scan BW Cash .............................................................................................................................................. 34 Scan Color Cash ....................................................................................................................................... 34

COPIER TYPE PANASONIC CASH PRICE SETTINGS ................................................................................................... 35 Small BW Cash ........................................................................................................................................... 35 Med. BW Cash .............................................................................................................................................. 35 Lrg. BW Cash .............................................................................................................................................. 35 Small CLR Cash ......................................................................................................................................... 35 Med. CLR Cash ........................................................................................................................................... 35 Lrg. CLR Cash ........................................................................................................................................... 35 Scan Job Cash ........................................................................................................................................... 35

CARD PRICES SETUP MODE ............................................................................................................................. 36

COPIER TYPE 2 PRICE: SETTINGS ............................................................................................................................ 36


Line1 Card Cost1 .................................................................................................................................... 36 Line1 Card Cost2 .................................................................................................................................... 36 Line1 Card Cost3 .................................................................................................................................... 36 Line1 Unit Cost1 .................................................................................................................................... 36 Line1 Unit Cost2 .................................................................................................................................... 37 Line1 Unit Cost1 .................................................................................................................................... 37 Line2 Card Cost1 .................................................................................................................................... 37 Line2 Card Cost2 .................................................................................................................................... 37 Line2 Card Cost3 .................................................................................................................................... 37 Line2 Unit Cost1 .................................................................................................................................... 37 Line2 Unit Cost2 .................................................................................................................................... 37 Line2 Unit Cost1 .................................................................................................................................... 37

COPIER TYPE MINOLTA 1; PRICE SETTINGS ............................................................................................................ 38 Small BW Card ........................................................................................................................................... 38 Med. BW Card .............................................................................................................................................. 38 Lrg. BW Card .............................................................................................................................................. 38 Small BW 2side ......................................................................................................................................... 38 Med. BW 2side ........................................................................................................................................... 38 Lrg. BW 2side ........................................................................................................................................... 38 Small CLR Card ......................................................................................................................................... 38 Med. CLR Card ........................................................................................................................................... 38 Lrg. CLR Card ........................................................................................................................................... 39 Small CLR 2side ....................................................................................................................................... 39 Med. CLR 2side ......................................................................................................................................... 39 Lrg. CLR 2side ......................................................................................................................................... 39 Small BW Units ......................................................................................................................................... 39 Med. BW Units ........................................................................................................................................... 39 Lrg. BW Units ........................................................................................................................................... 39 Small BW 2side ......................................................................................................................................... 39 Med. BW 2side ........................................................................................................................................... 39 Lrg. BW 2side ........................................................................................................................................... 40 Small CLR Units ....................................................................................................................................... 40 Med. CLR Units ......................................................................................................................................... 40 Lrg. CLR Units ......................................................................................................................................... 40 Small CLR 2side ....................................................................................................................................... 40 Med. CLR 2side ......................................................................................................................................... 40 Lrg. CLR 2side ......................................................................................................................................... 40

COPIER TYPE MINOLTA 2: PRICE SETTINGS ............................................................................................................ 40 Fax Page Card ........................................................................................................................................... 40 Fax Connect fee ....................................................................................................................................... 41 Scan BW Card .............................................................................................................................................. 41 Scan Color Card ....................................................................................................................................... 41 Fax Page Units ......................................................................................................................................... 41 Fax Connect fee ....................................................................................................................................... 41 Scan BW Units ........................................................................................................................................... 41 Scan Color Units .................................................................................................................................... 41

COPIER TYPE PANASONIC CARD PRICE SETTINGS ................................................................................................... 42 Small BW Card ........................................................................................................................................... 42 Med. BW Card .............................................................................................................................................. 42 Lrg. BW Card .............................................................................................................................................. 42 Small CLR Card ......................................................................................................................................... 42 Med. CLR Card ........................................................................................................................................... 42 Lrg. CLR Card ........................................................................................................................................... 42 Scan Job Card ........................................................................................................................................... 42

COPIER SETUP MODE ......................................................................................................................................... 43


Line 2 mode ................................................................................................................................................ 43 L1 Disable Delay .................................................................................................................................... 44 L2 Disable Delay .................................................................................................................................... 44 Return Delay .............................................................................................................................................. 44 Pulse Time mS ........................................................................................................................................... 44 Blind Time mS ........................................................................................................................................... 45 Relay 2 mode .............................................................................................................................................. 45 Pulse Clear Dly ....................................................................................................................................... 45 Num Clear Pulses .................................................................................................................................... 45 Pulse Clear On ......................................................................................................................................... 45 Pulse Clear Off ....................................................................................................................................... 45

PRINT SETUP MODE ............................................................................................................................................ 46

Com Port? ..................................................................................................................................................... 46 Disable Relay ........................................................................................................................................... 46 Ignore Pulses ........................................................................................................................................... 46

4715 FAX SETUP MODE ....................................................................................................................................... 47

Com Port? ..................................................................................................................................................... 47 Disable Relay ........................................................................................................................................... 47 Ignore Pulses ........................................................................................................................................... 47 Num Digits Local .................................................................................................................................... 47 calls Allowed ........................................................................................................................................... 47 Local Call Area Codes ...................................................................................................................................... 48 Area Code X ................................................................................................................................................ 48

4715 FAX PRICING SETUP MODE ..................................................................................................................... 49

Local P1 Cash ........................................................................................................................................... 49 Local P2 Cash ........................................................................................................................................... 49 L.D. P1 Cash .............................................................................................................................................. 49 L.D. P2 Cash .............................................................................................................................................. 49 INTL P1 Cash .............................................................................................................................................. 49 INTL P2 Cash .............................................................................................................................................. 49 Local P1 Card ........................................................................................................................................... 49 Local P2 Card ........................................................................................................................................... 50 L.D. P1 Card .............................................................................................................................................. 50 L.D. P2 Card .............................................................................................................................................. 50 INTL P1 Card .............................................................................................................................................. 50 INTL P2 Card .............................................................................................................................................. 50 Local P1 Unit ........................................................................................................................................... 50 Local P2 Unit ........................................................................................................................................... 50 L.D. P1 Unit .............................................................................................................................................. 50 L.D. P2 Unit .............................................................................................................................................. 50 INTL P1 Unit .............................................................................................................................................. 51 INTL P2 Unit .............................................................................................................................................. 51

BONUS SETUP MODE ........................................................................................................................................... 52

Use Bonuses? .............................................................................................................................................. 52 Bonus lvl 1 ................................................................................................................................................ 52 Bonus1 % to add ....................................................................................................................................... 52 Bonus lvl 2 ................................................................................................................................................ 52 Bonus2 % to add ....................................................................................................................................... 52 Bonus lvl 3 ................................................................................................................................................ 53 Bonus3 % to add ....................................................................................................................................... 53

DIAGNOSTICS MODE ............................................................................................................................................... 53


SERIAL PRINTER CABLE ................................................................................................................................... 54

SEIKO DPU 414 PRINTER SETTINGS ....................................................................................................................... 54

SERIAL PC CABLE ................................................................................................................................................ 55

PC SERIAL SETTINGS .............................................................................................................................................. 55

SERIAL USB CABLE .............................................................................................................................................. 55

USB DRIVER ........................................................................................................................................................... 55

INSTALLATION ..................................................................................................................................................... 56

PLACEMENT OF THE COIN, BILL AND CARD CONTROLLER ..................................................................................... 56 CONNECTING TO POWER ......................................................................................................................................... 56 COPIER CONTROL CABLE ....................................................................................................................................... 57

901-10-45-52 Generic Copier Cable ............................................................................................................... 57 CONNECTION TO THE COPIER ................................................................................................................................. 58

Enable: .............................................................................................................................................................. 58 Pulse: ................................................................................................................................................................ 58

CONNECTION TO EARTH GROUND .......................................................................................................................... 58 ALTERNATE CONNECTIONS: ................................................................................................................................... 59

Using a Paper Clutch ....................................................................................................................................... 59 SECOND PRICE (I.E. LARGE PAPER) CONNECTION: ................................................................................................. 60

-“Line 2 LEVEL Mode” .................................................................................................................................... 60 SECOND PRICE (I.E. LARGE PAPER) CONNECTION: ................................................................................................. 61

-“Line 2 PULSE Mode” ................................................................................................................................... 61 SECOND PRICE (I.E. LARGE PAPER) CONNECTION: ................................................................................................. 62

-“Line 2 PREMIUM Mode” ............................................................................................................................. 62 SUPPLY VOLTAGE .................................................................................................................................................. 63

SETUP WITH PRINT MANAGER ....................................................................................................................... 64

CONNECTING COMMUNICATION CABLE .................................................................................................................. 64 CONFIGURATION OF PRINT MANAGER .................................................................................................................... 64

CONNECTION TO 4517 FAX INTERFACE ....................................................................................................... 65

4517 INTERFACE CABLE ......................................................................................................................................... 65 4517 CONFIGURATION ............................................................................................................................................ 65

COIN CHANGER MANUAL ................................................................................................................................. 66

BILL ACCEPTOR MANUAL ................................................................................................................................ 75

COINCO BA30 FLASH CODES ................................................................................................................................. 81

ITC SYSTEMS – WARRANTY AND LIABILITY CONTRACT ...................................................................... 82


Sales and Service At ITC Systems, complete customer satisfaction is our number one goal. As such, customer support is readily available to satisfy any need you may have. Whether its sales information, a service requirement or just general inquiry, you can be assured of a prompt response to your need(s). SALES If you are a new or existing customer with a new installation in mind, our highly qualified sales staff can custom tailor a product solution for "your" particular needs. Simply telephone ITC in the United States at 314-872-7772 or in Canada at 416-289-2344 and ask for sales assistance. You may also email us at [email protected] UNITED STATES CANADA 800 Fee Fee Road 705 Progress Avenue, Unit 63, St. Louis, MO Toronto, Ontario 63043 M1H 2X1 Tel: (314)-872-7772 Tel: (416) 289-2344 Fax: (314)-872-3353 Fax: (416) 289-4790 SERVICE If you require technical assistance advice or parts please contact our SUPPORTEX department at 1-877-ITC-TEAM (482-8326) or 416-438-9332 or email us at [email protected] Repairs in the U.S.A. should be sent to: Repairs in Canada or International: ITC Systems U.S.A.. ITC Systems 800 Fee Fee Rd. 705 Progress Ave., Unit 43 St. Louis, MO 63043 Toronto, ON M1H 2X1 Tel: 314-872-7772 Tel: 416-438-9332 Fax: 314-872-3353 Fax: 416-438-6219 Please visit us at http://www.itcsystems.com ITC SYSTEMS . . . COMMITTED TO COMPLETE CUSTOMER SATISFACTION


Introduction ITC Systems 5400 Series Coin ops are available as 4 basic Models: 5410 Coin Only Controller 5420 Coin and Bill Controller 5410-10X Coin and Card Controller (X designates Card Track) 5420-10X Coin, Bill and Card Controller (X designates Card Track) Identifying the Components

Bypass

Card Reader

Display

Plunger

CoinReturn

Coin SlotCOM1

Lock

COM2USB

BillAcceptor


Operating Mode Displays Upon powering on the Coin op it will display the model number and firmware revision for 5 seconds 5400 Controller Ver XX.YY.ZZ It will then check the response from all enabled peripherals displaying the message: Initializing Peripherals... If there are any peripherals that do not respond correctly the display will show what unit is malfunctioning Bill Validator Not Responding. In the case of the Coin Acceptor not responding the controller will be put out of service Coin Acc Error OUT OF SERVICE Provided all peripherals initialize properly the following messages will be displayed depending upon how the unit is configured: Insert Coins Insert Coins or

Card Insert Coins or

Card Or Bills In the case where there is not sufficient coins in the changer to properly give change the Red Exact Change LED will be lit and the message will be: Insert Exact Change Only

or Insert Exact Change or Card

When money is deposited into the changer or bill validator or if a card is inserted into the reader the message will be: Make Copies Cash: $ ##.##

Make Copies Card: $ ##.##

If the Fax interface is enabled and there is sufficient funds to send a fax the “Make Copies” display will change to: Copy &Fax Ready Cash: $ ##.##

Copy &Fax Ready Card: $ ##.##


If the BizHub 2 interface is enabled and there is sufficient funds to make a Scan the “Make Copies” display will alternate with: or make Scan Cash: $ ##.##

or make Scan Card: $ ##.##

If copies have been made but the amount falls below the cost of the last copy made, the message will be: Insert Funds Cash: $ ##.##

Insert Funds Card: $ ##.##


Programming and Set-up Before using the 5400 pricing, options and interface characteristics have to be set up. This is achieved by using the Bypass key and Programming Switches or Optional Keypad Programming assembly. Opening the back door will gain access to the programming switches; Menu, Enter, Up and Down. The view below is from “inside” the coin box; therefore, looking from the front and reaching into the Coin Box, these switches will be reversed (Menu on the Right). The Switches are located inside the upper left corner beside the LCD Display. The Menu button steps through different menus. The Enter button sets the current value displayed in memory and advances to the next menu or function. The UP and Down buttons are used to change the current value displayed. Note pressing the UP button while the Down button is depressed will clear the current value to Zero. Turning the “Key-switch on top of the Coin box will initiate Bypass/Programming mode.

MENU Button ENTER Button UP Button DOWN Button

5400 Programming Push Button Locations and Keypad Assembly Connector

Connect Optional Keypad Cable Assembly Here


Board Layout

Using the Keypad for Programming Open the door of the Coin-op and Locate the Keypad Port J12 on the control board in the top of the cabinet. Connect the Keypad programming to J12. The D button is to Select a Menu (the same as the Menu button of the control board). The A button is used to move UP one level or selection in Menu or selection mode. The B button is used to move DOWN one level or selection in Menu or selection mode. Numeric entries can be made directly with the 0-9 buttons The CLR button is used to reset a current setting to its minimum or default value The ENT button is to Set or choose a selection or register a setting (the same as the Enter button of the control board).


Service Menus with Bypass Key OFF Press the Menu button to move between Root Menus. Press Enter button to select the root menu. The Up and Down also allow the user to toggle through the Root Menu as well as the menus themselves. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If a Keypad assembly is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set an entry to default or its minimum value.

BYPASS KEYOFF Idle Mode (Insert Coins, Bills or Card)

Coin Tube Levels View and Adjust Coin tube levels

Resetable Meters View or Send meters to Serial Port

Clear Resetable Meters

Grand Total Meters View or Send meters to Serial Port


Coin Tube Reporting In Idle mode (where the LCD displays Insert cash.) Pressing the Menu button once will initiate the Coin Tube Reporting function. Pressing the Enter button will scroll through the coin tube inventories by denomination. .25 .10 .05 ### ### ###

where ### is the number of coins in each tube

$0.05 0.00

$0.10 0.00

$0.25 0.00

Changing Coin Tube Inventory While a tube inventory is displayed on the LCD it can be manually manipulated via the Up or Down button. Pressing the Up and Down at the same time will set the inventory count for that tube to 0. Use the Up and down buttons until the inventory count matches the number of coins for that tube then press the Enter button to set it in memory. $0.05 0.15 Re-settable Meters Reporting Pressing the menu button again will advance to the Re-settable Meters Reporting module. At the prompt Resettable Meter

Press ENTER to select Resettable Meters

Send Meters to: LCD

Use the UP and Down button to select LCD, Com 1, USB, Com 3 or Com 4 followed by Enter.

Selecting LCD will scroll through the meters via LCD display. Selecting a Com port will send the meters out that port in an ASCII Text format that can be printed or captured on a PC. Refer to METERS REPORTS for an explanation and sample print out of the meters..


Clear Re-settable Meters Pressing the menu button again will advance to the Clear Re-settable Meters module. At the prompt Clear Resetable Meters UP+DOWN Pressing the Up and down button simultaneously will clear the re-settable meters and increase the meters clears counter by one. Grand Meters Reporting Pressing the menu button again will advance to the Grand total (Non re-settable) Meters Reporting module. At the prompt Grand Meters

Press ENTER to select Grand Total Meters

Send Meters to: LCD

Use the UP and Down button to select LCD, Com 1, USB, Com 3 or Com 4 followed by Enter.

Selecting LCD will scroll through the meters via LCD display. Selecting a Com port will send the meters out that port in an ASCII Text format that can be printed or captured on a PC. Refer to METERS REPORTS for an explanation and sample print out of the meters.. Pressing the Menu button again will return the controller to Idle mode. Insert Coins Insert Coins or

Card Insert Coins or

Card Or Bills


Loading the coin tubes To initially load the tubes it is permissible to load coins directly into the Coin changer’s Inventory tubes. Fill the tubes with a known quantity of each coin. After loading the tubes the quantity of each coin must be programmed into memory. Press the “MENU” button on the main control board. The display will indicate .25 .10 .05 ### ### ###


NOTE: The tube configuration in your controller may have a different tube configuration depending on the model and market. Press the “ENTER” button. To adjust the Quarters tube level press the “UP” or “Down” button until the correct value is displayed on the LCD. Press the “ENTER” button. To adjust the Dimes tube level press the “UP” or “Down” button until the correct value is displayed on the LCD. Press the “ENTER” button. To adjust the Nickels tube level press the “UP” or “Down” button until the correct value is displayed on the LCD. Press the “ENTER” button. $0.05 0.00

$0.10 0.00

$0.25 0.00

Topping off the coin tubes To add coins to the partially filled turn the “BYPASS KEY” then, press the “MENU” Button. The display will indicate: .25 .10 .05 ### ### ###


As coins are inserted the appropriate value will increment. Turn the bypass key to off when finished to record new values and exit the mode. Any coins added in this mode will be added to the total coin count automatically. Coins added directly to the inventory tubes will not be counted causing false “Out Of Change” situations. Tube Capacity: Approx. Values 5¢ tube ....................... 85 coins ................. $4.30 10¢ tube ..................... 125 coins ............. $12.50 25¢ tube ..................... 95 coins ............... $23.75


METERS REPORTS Re-settable Meters Below is a sample print out of the Re-settable meters. Meters for options that are not enabled (card, bill, fax etc) will not be displayed or printed. ******************************* Model 5400 Transaction log for Unit ID # 1 07/03/07 10:38:48 RESETTABLE Meters User Coin In $ .00 User Coin Out $ .00 Coin To Bin $ .00 Bypass Coin In $ .00 Unpaid Escrow $ .000 Slugs rejected # 0 User Bills In $ .00 $Card In Site 1 $ .000 $Card In Site 2 $ .000 $Card In Site 3 $ .000 UCard In Site 1 # 0 UCard In Site 2 # 0 UCard In Site 3 # 0 Amt added to $ $ .000 Amt added to U # 0 Bonus to $ Card $ .000 Bonus to U Card # 0 L1 Bypas Copies # 0 L2 Bypas Copies # 0 Value Print Cash $ .000 Value Print Card $ .000 Value Print Unit # 0 L1 Cash Copies # 0

L2 Cash Copies # 0 L1 Card Copies # 0 L2 Card Copies # 0 L1 Unit Copies # 0 L2 Unit Copies # 0 FAX Loc P1 Byp # 0 FAX Loc P2 Byp # 0 FAX Lng P1 Byp # 0 FAX Lng P2 Byp # 0 FAX Int P1 Byp # 0 FAX Int P2 Byp # 0 FAX Loc P1 Cash # 0 FAX Loc P2 Cash # 0 FAX Lng P1 Cash # 0 FAX Lng P2 Cash # 0 FAX Int P1 Cash # 0 FAX Int P2 Cash # 0 FAX Loc P1 $Card # 0 FAX Loc P2 $Card # 0 FAX Lng P1 $Card # 0 FAX Lng P2 $Card # 0 FAX Int P1 $Card # 0 FAX Int P2 $Card # 0 FAX Loc P1 UCard # 0 FAX Loc P2 UCard # 0 FAX Lng P1 UCard # 0 FAX Lng P2 UCard # 0 FAX Int P1 UCard # 0 FAX Int P2 UCard # 0 End of report


Grand Total Meters Below is a sample print out of the Grand Total Meters. Meters for options that are not enabled (card, bill, fax etc) will not be displayed or printed. ******************************* Model 54xx Transaction log for Unit ID # 1 07/03/07 13:51:00 NON_RESETTABLE Meters User Coin In G $ .00 User Coin Out G $ .00 Coin To Bin G $ .00 Bypass Coin In G $ .00 Unpaid Escrow G $ .000 Slugs rejected G # 0 User Bills In G $ .00 $Card In Site 1 G $ .000 $Card In Site 2 G $ .000 $Card In Site 3 G $ .000 UCard In Site 1 G # 0 UCard In Site 2 G # 0 UCard In Site 3 G # 0 Amt added to $ G $ .000 Amt added to U G # 0 Bonus to $ Card G $ .000 Bonus to U Card G # 0 L1 Bypas Copies G # 0 L2 Bypas Copies G # 0 Value Print Cash G $ .000 Value Print Card G $ .000 Value Print Unit G # 0 L1 Cash Copies G # 0

L2 Cash Copies G # 0 L1 Card Copies G # 0 L2 Card Copies G # 0 L1 Unit Copies G # 0 L2 Unit Copies G # 0 FAX Loc P1 Byp G # 0 FAX Loc P2 Byp G # 0 FAX Lng P1 Byp G # 0 FAX Lng P2 Byp G # 0 FAX Int P1 Byp G # 0 FAX Int P2 Byp G # 0 FAX Loc P1 Cash G # 0 FAX Loc P2 Cash G # 0 FAX Lng P1 Cash G # 0 FAX Lng P2 Cash G # 0 FAX Int P1 Cash G # 0 FAX Int P2 Cash G # 0 FAX Loc P1 $Card G # 0 FAX Loc P2 $Card G # 0 FAX Lng P1 $Card G # 0 FAX Lng P2 $Card G # 0 FAX Int P1 $Card G # 0 FAX Int P2 $Card G # 0 FAX Loc P1 UCard G # 0 FAX Loc P2 UCard G # 0 FAX Lng P1 UCard G # 0 FAX Lng P2 UCard G # 0 FAX Int P1 UCard G # 0 FAX Int P2 UCard G # 0 End of report

May 2008 P 19 of 82 Z:\CABINETS\Service\MANUALS\CURRENT\5400\5400_USA_rev1_7.doc rev 1.6B2

Bypass/Programming Mode The Bypass mode serves 2 functions. The first is to allow “Free” copies for administration or service technicians. When the bypass mode is enabled the display reads: Bypass Mode Copies: ###

Where ### is the number of copies made during this bypass session

The second Bypass Mode function sets up the prices, options and necessary parameters needed for the controller’s operation. By turning the “BYPASS KEY” and pressing the “MENU” button it is possible to step to a specific setup function without going through all. If a Keypad assembly is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set an entry to default or its minimum value. The functions available in Programming mode are: Coin Tube Levels Language Diagnostics Mode Peripherals Coin Changer Bill Acceptor Costs Interface To initiate the “Bypass/Programming” mode turn the “BYPASS KEY.” 90 degrees clockwise. The display will indicate: “Bypass Mode” “Copies X”. In Bypass mode the copier is “enabled” to allow copies. Any copies made in the bypass mode are recorded as “Bypass copies” by the Coin box meters. The meters are described in detail later in this manual. To initiate the Programming mode press the “MENU” button on the CPU board (D on the Keypad).


BYPASS KEYON Bypass Mode (make bypass Copies)

Coin Tube Levels View Coin tube levels while topping off

System Setup Set ID

Set Date

Set Time

Set Copier Type

Enable Printing

Enable Faxing (Via 4517 Interface)

Set Language

Peripherals Enable Card Reader

Enable Bill Acceptor

Coin Changer Settings Return Escrow Setting

Maximum Escrow Value

Minimum Escrow Value

Cancel if Escrow is less than Price 2

Card Reader Setup * Card Types (Cash / Units) to Accept

Card Format

Accept ICS / XCP Format Cards *

Convert to ACDI *

Accept Danyl Format Cards *

Set Card STX *

Set Card ROM *

Bill Acceptor Settings * Set each bill value to accept

NOTE:Menus and Options

denoted with * (Asterisk) will not

appear if they do not apply to the current configuration of the

Coin-op.i.e. if the Bill Acceptor

is Disabled, the Bill Acceptor Settings menu would not

appear.

Page 1 of 3


Card Reader Setup (Continued)* Set Site 1

Set Site 2

Set Site 3

Display tenth of a Cent

Maximum Cash Value card to Accept *

Maximum Units Value card to Accept *

Allow adding of Value with Coins

Allow adding of Value with Bills *

Allow adding of Value to Units Cards *

Value of cents to add 1 Unit *

Danyl Site codes to Convert *

Sideboard Type

BYPASS KEYON (Continued)






appear.

Copier Cash Prices Setup Set Prices for different Sizes and Options

Copier Card Prices Setup Set Prices for different Sizes and Options

Copier Settings * Input Line 2 Operation Mode *

Input Line 1 Disable Delay *

Input Line 2 Disable Delay *

Coin (Card) Return Delay time

Copy Signal Pulse Time *

Copy Signal Blind Time *

Relay 2 Mode *

Delay before Clear Pulses *

Number of Clear Pulses *

Clear Pulses ON Time *

Clear Pulses OFF Time *

Page 2 of 3


Print Setup Mode * Assign Com Port

Set Disable Enable Relay

Set Ignore Copy Pulses

BYPASS KEYON (Continued)






appear.

Fax Interface Setup Mode * Assign Com Port

Set Disable Enable Relay

Set Ignore Copy Pulses

Set Number of Digits for a Local call

Set Call types Allowed

Set Dialing Prefix

Set Area Codes of Local Calls

Fax Prices Setup Set Cash Prices for Sending Faxes

Set Cash Card Prices for Sending Faxes

Set Units Card Prices for Sending Faxes

Cash to Card Bonus Setup Mode * Set Use Bonuses

Setup Bonus 1*

Setup Bonus 2*

Setup Bonus 3*

Diagnostic Mode (Factory use Only)

Page 3 of 3


Coin Tube (Inventory) Mode In Coin Tube Inventory mode the display will show: .25 .10 .05 ### ### ###


Coins can be added through the coin slot at this time and the coin inventory will be adjusted appropriately. Press the “MENU” button to Continue System Setup Mode Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. System Setup Set Date

Press Enter to set date.

yy mm dd ##/##/##

Change year with UP and Down then press Enter. Set month and day.

System Setup Set Time

Press Enter to set time.

hh mm ss ##/##/##

Change hour with UP and Down then press Enter. Set minute and seconds.

System Setup Unit ID

Press Enter to set ID.

Unit ID 1

Change Unit ID with UP and Down then press Enter.

The unit ID is for tracking the Controller when meters reports are printed or viewed.


System Setup Copier Type

Press Enter to set Copier type.

Copier Type Copier/2 Pr

Change the Copier type with UP and Down then press Enter.

Copier types include: Copier 2 Price (uses standard or copier Specific cable). Minolta Vendor 1 (uses Optional cable through J8 on PCB). Minolta Vendor 2 (uses Optional cable through J8 on PCB). *4210 Panasonic (uses 4210 Interface Configured for Panasonic) *4210 Sharp (uses 4210 Interface Configured for Panasonic). *4210 Generic (uses 4210 Interface in Generic Configuration). None (used for controlling Faxing and or Printing only). * See additional Install / operation manuals and documents for these 4210 Interface Modes System Setup Enable Printing

Press Enter to set Printing.

Enable Printing No

Select Yes or No with the UP and Down then press Enter.

Enables printing through a print management station connected to Serial port. System Setup Enable Fax

Press Enter to set Fax.

Enable Fax No


Enables Faxing through an optional interface (4517). System Setup Language

Press Enter to set language.

Language English

Select English or French with the UP and Down then press Enter.

Press Menu to exit System Setup mode


Peripherals Setup Mode Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. System Setup Card Reader

Press Enter to set card reader.

Peripherals Card Reader


System Setup Bill Installed

Press Enter to set card bill acceptor.

Peripherals Bill Installed


Press Menu to exit Peripherals Setup mode


Bills Setup Mode This mode will only appear if the bill acceptior is enabled in peripherals Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. Set Bills Accept 1.00

Press Enter to set 1.00 bill acceptance. Only appears if installed acceptor accepts this bill.

Accept $1.00 Yes


Set Bills Accept 5.00


Accept $5.00 Yes

Select Yes, No or “card only” with the UP and Down then press Enter. Card only enables bill only if a card is in the reader



Accept $10.00 Yes




Accept $20.00 Yes




Accept $50.00 Yes




Accept $100.00 Yes


Press Menu to exit Bill Acceptor Setup mode


Coin Changer Setup Mode Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. Coin Changer Return Escrow

Press Enter to set Coin Return Escrow

Return Escrow Anytime

Select Return Escrow operation with the UP and Down then press Enter.

Return Escrow Options: -Any Time (coins will be returned anytime the plunger is pressed) -Only after use(coins will be only after a job has been made. This prevents the controller from being used as a change machine) -Serial Control (gives control to Print Management application). Coin Changer Max Escrow Value

Press Enter to set Maximum Escrow Value.

Max Escrow Value $5.00

Set the Max Escrow value allowed to accumulate before disabling cash acceptance, with the UP and Down then press Enter.

Coin Changer Min Escrow Value

Press Enter to set Minimum Escrow Value.

Min Escrow Value $5.00

Set the Minimum Escrow value before the enable relay opens, with the UP and Down then press Enter. 0.00 disables this function.

Coin Changer ESCROW<P2=CANCEL

Press Enter to set Escrow Cancel mode.

ESCROW<P2=CANCEL No


This function will disable the controller if the credit in Escrow falls below the price of Line 2 job. Press Menu to exit Coin Changer Setup mode


Card Reader Setup Mode This mode will only appear if the card reader is enabled in peripherals Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. Card Readr Setup Accept Types

Press Enter to set cards types to accept

Accept Both

Select Cash, Units or Both with UP and Down then press Enter to set the card types accepted by the controller.

Card Readr Setup Card Format

Press Enter to set card Format to accept

Card Format ACT/ITC

Select the card format ACT/ITC, VCS, Danyl, ICS/XCP with UP and Down then press Enter.

Card Readr Setup Accept ICS/XCP

Press Enter to set conversion of ICS or XCP formatted cards.

Accept ICS/XCP NO

Select No, Convert to Site 1 or Convert to site 2 with UP and Down then press Enter.

This will allow ICS or XCP formatted cards to be accepted and converted to ACT/ITC format. The cards will be encoded to site 1 or 2 as selected. Card Readr Setup Convert to ACDI

Press Enter to set conversion of cards to ACDI format.

Convert to ACDI NO


Card Readr Setup Accept Danyl

Press Enter to set conversion of Danyl cards.

Accept Danyl NO


This will allow Danyl cards to be accepted and converted to ACT/ITC format. The cards will be encoded to site 1 or 2 as selected.


STX and ROM Definition Within most card formats there are different “ROM Code” combinations to expand the availability of unique site codes for different institutions and installations. Traditionally these have been set on DIP Switches or hard coded into the firmware. With the Coin controller these are set under the Card Reader set-up mode. To set the “ROM Code” on the controller it must be broken into 2 “nibbles” hence the terms STX (Start nibble of the “ROM Code”) and ROM (second nibble of the “ROM Code”). The STX and ROM are hexadecimal (HEX) values which have to be converted to decimal for entry purposes. The tables below the HEX to Decimal conversions and some common examples of “ROM Codes”. STX or ROM

in HEX

Setting to use In

Decimal

STX or ROM

in HEX

Setting to use

In Decimal

Common “ROM Codes”

STX Setting Rom Setting

0 0 8 8 B9 11 9 1 1 9 9 C1 12 1 2 2 A 10 C2 12 2 3 3 B 11 C3 12 3 4 4 C 12 C4 12 4 5 5 D 13 C5 12 5 6 6 E 14 40 4 0 7 7 F 15 A5 10 5

Card Readr Setup Reader STX

Press Enter to set card STX

Reader STX 12

Set the value with UP and Down then press Enter.

Card Readr Setup Reader ROM

Press Enter to set card STX

Reader ROM 4


Card Readr Setup Site 1

Press Enter to set card site 1

Site 1 164




Site 2 4095

Set the value with UP and Down then press Enter. A setting of 4095 indicates site 2 is not used.




Site 3 4095

Set the value with UP and Down then press Enter. A setting of 4095 indicates site 3 is not used.

Card Readr Setup Display tenths/c

Press Enter to set tenth of a cent display option

Display tenths/c No


Card Readr Setup Max Value Cash

Press Enter to set the maximum Cash Card value to accept.

Max Value Cash $79.00

Set the value with UP and Down then press Enter. $0.00 will disable Cash cards.

Card Readr Setup Max Value Units

Press Enter to set the maximum Units Card value to accept.

Max Value Units 200

Set the value with UP and Down then press Enter. 0 will disable Units cards.

Card Readr Setup Add Value w/Coin

Press Enter to set Adding value to the card with coins option

Add Value w/coin Yes


Card Readr Setup Add Value w/Bill

Press Enter to set Adding value to the card with Bills option

Add Value w/Bill Yes


Card Readr Setup Add Val to units

Press Enter to set Adding value to Units card option

Add Val to units Yes


Card Readr Setup Cents per unit

Press Enter to set the number of cents to add 1 unit to the card.

Cents per unit 1

Set the value with UP and Down then press Enter. i.e. A setting of 5 would add 20 units per dollar inserted.


Card Readr Setup dSite 4 (5-10)

Press Enter to set the site code (s) 4 to 10 of Danyl cards to be converted to ITC format.

dSite 4 (5-10) 4

Set the value with UP and Down or Via keypad for each site then press Enter.

Card Readr Setup Sideboard Type

Press Enter to set the Card reader’s Sideboard type.

Sideboard Type Advanced

Set Advanced or Classic with UP and Down then press Enter.

Select Advanced for “902-1500-SB” Side board Select Classic for “A5050-2” Side board Contact Supportex for details if unsure of side board type. Press Menu to exit Card Reader Setup mode


Cash Prices Setup Mode This mode is used to set the prices for copies. Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. Copier Type 2: Price settings The following price settings will be set if the copier type in system setup is set to 2 price interface. The 2 price interface is built into the controller board and is the default interface. With the 2 Price interface there are 2 input lines to indicate when copies have been made. Depending upon the model of copier and installation method this allows a different price to be charged for 2 sizes of paper or a different price between Black and Colour copies. Copy Prices Cash Line 1 Cash Cost

Press Enter to set the cash price for copy input line 1

Line1 Cash Cost $ .10

Set the price with the Up and Down then press Enter.

Copy Prices Cash Line 2 Cash Cost

Press Enter to set the cash price for copy input line 2

Line1 Cash Cost $ .20


Press Menu to exit Cash Price Setup mode Copier Type Minolta 1: Price settings The following price settings will be set if the copier type in system setup is set to Minolta 1 interface. Costs Cash Small BW Cash

Press Enter to set the cash price for a Small sized Black and White copy.

Small BW Cash $ .05



Costs Cash Med. BW Cash

Press Enter to set the cash price for a Medium sized Black and White copy.

Med BW Cash $ .10


Costs Cash Lrg. BW Cash

Press Enter to set the cash price for a Large sized Black and White copy.

Lrg BW Cash $ .15


Costs Cash Small BW 2side

Press Enter to set the cash price for a Small sized Black and White 2 sided copy.

Small BW 2side $ .20


Costs Cash Med. BW 2side

Press Enter to set the cash price for a Medium sized Black and White 2 sided copy.

Med BW 2side $ .25


Costs Cash Lrg. BW 2side

Press Enter to set the cash price for a Large sized Black and White 2 sided copy.

Lrg BW 2side $ .30


Costs Cash Small CLR Cash

Press Enter to set the cash price for a Small sized Colour copy.

Small CLR Cash $ .35


Costs Cash Med. CLR Cash

Press Enter to set the cash price for a Medium sized Colour copy.

Med CLR Cash $ .40


Costs Cash Lrg. CLR Cash

Press Enter to set the cash price for a Large sized Colour copy.

Lrg CLR Cash $ .45


Costs Cash Small CLR 2side

Press Enter to set the cash price for a Small sized Colour 2 sided copy.

Small CLR 2side $ .50



Costs Cash Med. CLR 2side

Press Enter to set the cash price for a Medium sized Colour 2 sided copy.

Med CLR 2side $ .55


Costs Cash Lrg. CLR 2side

Press Enter to set the cash price for a Large sized Colour 2 sided copy.

Lrg CLR 2side $ .60


Press Menu to exit Cash Price Setup mode Copier Type Minolta 2: Price settings In addition to the prices set in Minolta 1, the following price settings will be set if the copier type in system setup is set to Minolta 2 interface. Costs Cash Fax Page Cash

Press Enter to set the cash price for a Faxed Page.

Fax Page Cash $ .01


Costs Cash Fax Connect fee

Press Enter to set the cash price for a Fax to connect (initiate a call)

Connect fee $ .01


Costs Cash Scan BW Cash

Press Enter to make a Black and White Scan

Scan BW Cash $ .01


Costs Cash Scan Color Cash

Press Enter to make a color Scan

Scan Color Cash $ .04


Press Menu to exit Cash Price Setup mode


Copier Type Panasonic Cash Price settings The following price settings will be set if the copier type in system setup is set to 4210 Panasonic interface. Prices Cash Small BW Cash

Press Enter to set the cash price for a Small sized Black and White copy.

Small BW Cash $ .05


Prices Cash Med. BW Cash

Press Enter to set the cash price for a Medium sized Black and White copy.

Med BW Cash $ .10


Prices Cash Lrg. BW Cash

Press Enter to set the cash price for a Large sized Black and White copy.

Lrg BW Cash $ .15


Prices Cash Small CLR Cash

Press Enter to set the cash price for a Small sized Colour copy.

Small CLR Cash $ .35


Prices Cash Med. CLR Cash

Press Enter to set the cash price for a Medium sized Colour copy.

Med CLR Cash $ .40


Prices Cash Lrg. CLR Cash

Press Enter to set the cash price for a Large sized Colour copy.

Lrg CLR Cash $ .45


Prices Cash Scan Job Cash

Press Enter to set the cash price to make a Scan

Scan Cost Cash $ ..01



Card Prices Setup Mode This mode is used to set the prices for copies. If the card reader is disabled under peripherals the menus for card prices will not appear. Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. Copier Type 2 Price: settings The following price settings will be set if the copier type in system setup is set to 2 price interface. The 2 price interface is built into the controller board and is the default interface. With the 2 Price interface there are 2 input lines to indicate when copies have been made. Depending upon the model of copier and installation method this allows a different price to be charged for 2 sizes of paper or a different price between Black and Colour copies. Copy Prices Cash Line1 Card Cost1

Press Enter to set the cash card price for copy input line 1 Site Code 1

Line1 Cash Cost1 $ .080


Copy Prices Cash Line1 Card Cost2








Copy Prices Cash Line1 Unit Cost1

Press Enter to set the Unit card price for copy input line 1 Site Code 1

Line1 Unit Cost1 $ .080












Press Enter to set the cash card price for copy input Line 2 Site Code 1












Press Enter to set the Unit card price for copy input Line 2 Site Code 1











Press Menu to exit Card Price Setup mode


Copier Type Minolta 1; Price settings The following price settings will be set if the copier type in system setup is set to Minolta 1 interface. Costs Card Small BW Card

Press Enter to set the Card price for a Small sized Black and White copy.

Small BW Card $ .05


Costs Card Med. BW Card

Press Enter to set the Card price for a Medium sized Black and White copy.

Med BW Card $ .10


Costs Card Lrg. BW Card

Press Enter to set the Card price for a Large sized Black and White copy.

Lrg BW Card $ .15


Costs Card Small BW 2side

Press Enter to set the Card price for a Small sized Black and White 2 sided copy.



Costs Card Med. BW 2side

Press Enter to set the Card price for a Medium sized Black and White 2 sided copy.

Med BW 2side $ .25


Costs Card Lrg. BW 2side

Press Enter to set the Card price for a Large sized Black and White 2 sided copy.

Lrg BW 2side $ .30


Costs Card Small CLR Card

Press Enter to set the Card price for a Small sized Colour copy.

Small CLR Card $ .35


Costs Card Med. CLR Card

Press Enter to set the Card price for a Medium sized Colour copy.

Med CLR Card $ .40



Costs Card Lrg. CLR Card

Press Enter to set the Card price for a Large sized Colour copy.

Lrg CLR Card $ .45


Costs Card Small CLR 2side

Press Enter to set the Card price for a Small sized Colour 2 sided copy.



Costs Card Med. CLR 2side

Press Enter to set the Card price for a Medium sized Colour 2 sided copy.

Med CLR 2side $ .55


Costs Card Lrg. CLR 2side

Press Enter to set the Card price for a Large sized Colour 2 sided copy.

Lrg CLR 2side $ .60


Costs Units Small BW Units

Press Enter to set the Units price for a Small sized Black and White copy.

Small BW Units $ .05


Costs Units Med. BW Units

Press Enter to set the Units price for a Medium sized Black and White copy.

Med BW Units $ .10


Costs Units Lrg. BW Units

Press Enter to set the Units price for a Large sized Black and White copy.

Lrg BW Units $ .15


Costs Units Small BW 2side

Press Enter to set the Units price for a Small sized Black and White 2 sided copy.



Costs Units Med. BW 2side

Press Enter to set the Units price for a Medium sized Black and White 2 sided copy.

Med BW 2side $ .25



Costs Units Lrg. BW 2side

Press Enter to set the Units price for a Large sized Black and White 2 sided copy.

Lrg BW 2side $ .30


Costs Units Small CLR Units

Press Enter to set the Units price for a Small sized Colour copy.

Small CLR Units $ .35


Costs Units Med. CLR Units

Press Enter to set the Units price for a Medium sized Colour copy.

Med CLR Units $ .40


Costs Units Lrg. CLR Units

Press Enter to set the Units price for a Large sized Colour copy.

Lrg CLR Units $ .45


Costs Units Small CLR 2side

Press Enter to set the Units price for a Small sized Colour 2 sided copy.



Costs Units Med. CLR 2side

Press Enter to set the Units price for a Medium sized Colour 2 sided copy.

Med CLR 2side $ .55


Costs Units Lrg. CLR 2side

Press Enter to set the Units price for a Large sized Colour 2 sided copy.

Lrg CLR 2side $ .60


Press Menu to exit Cash Price Setup mode Copier Type Minolta 2: Price settings In addition to the prices set in Minolta 1, the following price settings will be set if the copier type in system setup is set to Minolta 2 interface. Costs Card Fax Page Card

Press Enter to set the Card price for a Faxed Page.

Fax Page Card $ .01



Costs Card Fax Connect fee

Press Enter to set the Card price for a Fax to connect (initiate a call)

Connect fee $ .01


Costs Card Scan BW Card


Scan BW Card $ .01


Costs Card Scan Color Card


Scan Color Card $ .04


Costs Units Fax Page Units

Press Enter to set the Units price for a Faxed Page.

Fax Page Units $ .01


Costs Units Fax Connect fee

Press Enter to set the Units price for a Fax to connect (initiate a call)

Connect fee $ .01


Costs Units Scan BW Units


Scan BW Units $ .01


Costs Units Scan Color Units


Scan Color Units $ .04


Press Menu to exit Units Price Setup mode


Copier Type Panasonic Card Price settings The following price settings will be set if the copier type in system setup is set to 4210 Panasonic interface. Prices Card Small BW Card

Press Enter to set the Card price for a Small sized Black and White copy.

Small BW Card $ .05


Prices Card Med. BW Card

Press Enter to set the Card price for a Medium sized Black and White copy.

Med BW Card $ .10


Prices Card Lrg. BW Card

Press Enter to set the Card price for a Large sized Black and White copy.

Lrg BW Card $ .15


Prices Card Small CLR Card

Press Enter to set the Card price for a Small sized Colour copy.

Small CLR Card $ .35


Prices Card Med. CLR Card

Press Enter to set the Card price for a Medium sized Colour copy.

Med CLR Card $ .40


Prices Card Lrg. CLR Card

Press Enter to set the Card price for a Large sized Colour copy.

Lrg CLR Card $ .45


Prices Card Scan Job Card

Press Enter to set the Card price to make a Scan

Scan Cost Card $ ..01



Copier Setup Mode This mode is used to set the Copier interface characteristics. Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. Copier Setup Line 2 mode

Press Enter to set the line 2 mode

Line 2 mode Pulse

Select Pulse, Level or Premium with the UP and Down then press Enter.

In Pulse Mode, Price 2 is charged whenever a pulse is detected on the Line 2 input. This mode would be used when individual cassette pick-up solenoids are connected to the Line 1 and PLine 2 signal inputs. In the LEVEL Mode, the input on line 2 acts like a Shift key on a keyboard. If line 2 is active before, during and after a pulse is detected on price input1, the value programmed for Price 2 is charged.

ON Line 2 Signal OFF ON Line 1 Signal OFF

Price 2 Charged Price 1 Charged

ON Line 2 Signal OFF “Large Paper Clutch” ON Line 1 Signal OFF “Auditron Output”

Price 2 Charged Price 1 Charged


In Premium Mode, Price 2 is deducted when the line 2 input is activated and the Price 1 input is ignored for the next pulse as this is for the same page. Copier Setup L1 Disable Delay

Press Enter to set the line 1 Disable Delay.

L1 Disable Delay mS 0

Set the Disable Delay time in milliseconds with the Up and Down then press Enter.

L1 Disable Delay time can be used to cause the controller to delay the delay by the number of seconds specified after reception of a copy pulse on Line 1. This feature is sometimes necessary to prevent paper jams or blank pages from being printed. Copier Setup L2 Disable Delay

Press Enter to set the line 2 Disable Delay.

L2 Disable Delay mS 0

Set the Disable Delay time in milliseconds with the Up and Down then press Enter.

L2 Disable Delay time can be used to cause the controller to delay the delay by the number of seconds specified after reception of a copy pulse on Line 2. This feature is sometimes necessary to prevent paper jams or blank pages from being printed. Copier Setup Return Delay

Press Enter to set the Coin / Card mode Return delay

Return Delay Sec 2

Set the Disable Delay time in seconds with the Up and Down then press Enter.

Return Delay is used to ensure that all copy pulses have been received by the controller before coins or the card is returned to the patron. On some copiers it may take up to 12 seconds after pressing copy before the pulse is generated. Copier Setup Pulse Time mS

Press Enter to set the pulse time coming from the copier.

Pulse Time mS 20

Set the Pulse Time in Milliseconds with the Up and Down then press Enter.

The Pulse time sets the shortest pulse that the controller will recognize as a valid copy.

ON line 2 Signal OFF “Large Paper Clutch” ON line 1 Signal OFF “Auditron”

Price 2Charged No Charge Price 1 Charged


Copier Setup Blind Time mS

Press Enter to set the Blind time between copy pulses

Blind Time mS 500

Set the Blind Time in Milliseconds with the Up and Down then press Enter.

The Blind time is set to ignore activity after a valid copy pulse is received. This can be used to ignore multiple pulses generated by the copier or to avoid noisy circuits from triggering false pulses. Copier Setup Relay 2 mode

Press Enter to set the relay 2 mode

Relay 2 mode Price 2

Select Price 2 or Pulse Clear with the Up and Down then press Enter.

In Price 2 mode Relay 2 turns on when there is sufficient credit to make a Line 2 copy In Pulse Clear mode the second relay can be used to simulate the pressing of the Stop or Clear button on the Copier. In this case the relay would be hard wired across the Stop or Clear button of the Copiers control panel. A custom harness would be required for this connection. Copier Setup Pulse Clear Dly

Press Enter to set the Pulse clear delay time. This setting will only appear if pulse clear mode was selected above.

Pulse Clear Dly 100

Set the Pulse Clear Delay in Milliseconds with the Up and Down then press Enter.

This is the delay time between disabling the copier and generating the Pulse clear pulses. Copier Setup Num Clear Pulses

Press Enter to set the number of Clear Pulses. This setting will only appear if pulse clear mode was selected above.

Num Clear Pulses 2

Set the number of pulses with the Up and Down then press Enter.

Copier Setup Pulse Clear On

Press Enter to set the Pulse On time. This setting will only appear if pulse clear mode was selected above.

Pulse Clear On Time 100

Set the Pulse Clear On Time Milliseconds with the Up and Down then press Enter.

This is the length of time the relay will be turned On (Closed) for each clear pulse Copier Setup Pulse Clear Off

Press Enter to set the Pulse Off time. This setting will only appear if pulse clear mode was selected above.

Pulse Clear Off Time 100

Set the Pulse Clear Off Time Milliseconds with the Up and Down then press Enter.

This is the length of time the relay will be turned Off (Opened) between each clear pulse Press Menu to exit Copier Setup mode


Print Setup Mode This mode is used to set the Print Settings. Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. When printing on some multifunction machines the following settings may be needed. Print Setup Com Port?

Press Enter to select the Com port to be used for printing.

Com Port? Com 1

Select COM1 (DB9) or USB with the Up and Down then press Enter.

IMPORTANT NOTE: The power must be re-set after changing the Com port setting for the change to be applied. Print Setup Disable Relay

Press Enter to Disable the enable relay when printing.

Disable Relay Yes

Select Yes or No with the Up and Down then press Enter. If set to yes and printing is initiated the Enable relay will open

Print Setup Ignore Pulses

Press Enter to ignore copy pulses when printing.

Ignore Pulses Yes

Select Yes or No with the Up and Down then press Enter. If set to yes and printing is initiated copy pulses will not be counted

Press Menu to exit Print Setup mode


4715 Fax Setup Mode This mode is used to set 4517 Fax interface Settings. Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. 4517 Fax Setup Com Port?

Press Enter to select the Com port that the 4517 Fax Controller is connected to

Com Port? COM4

Select COM1 or COM4 with the Up and Down then press Enter.

4517 Fax Setup Disable Relay

Press Enter to Disable the enable relay when Faxing. When faxing on some multifunction machines this settings may be needed.

Disable Relay Yes

Select Yes or No with the Up and Down then press Enter. If set to yes and faxing is initiated the Enable relay will open

4517 Fax Setup Ignore Pulses

Press Enter to ignore copy pulses when faxing. When faxing on some multifunction machines this settings may be needed.

Ignore Pulses Yes

Select Yes or No with the Up and Down then press Enter. If set to yes and faxing is initiated copy pulses will not be counted

4517 Fax Setup Num Digits Local

Press Enter to set the number of digits dialed for a local Fax. Applies to numbers not starting with 0 or 1

Num Digits Local 0

Set the number of digits dialed for a local Fax with the Up and Down then press Enter.

4517 Fax Setup calls Allowed

Press Enter to set the code for the types of Faxes allowed

calls Allowed 1

Set the code number with the Up and Down then press Enter. Code description is listed below:

1 = Local Faxes 2 = Long Distance Faxes 3 = Local + Long Distance Faxes 4 = International Faxes 5 = International + Local Faxes 6 = International + Long 7 = International + Long Distance + Local Faxes Distance Faxes


Local Call Area Codes In some locations there are area codes that although take on a long distance dialing pattern but are not actually long distance calls. To allow for this up to 10 area codes can be set to charge as local calls. 4517 Fax Setup Area Code X

Press Enter to set an area code to be charged as local. 10 area codes can be set.

Are Code X 000

Set the each digit with the Up and Down then press Enter to move to the next digit.

Press UP and Down together to reset to 000 (used to indicate no area code) Press Menu to exit 4517 Fax Setup mode


4715 Fax Pricing Setup Mode This mode is used to set 4517 Fax interface pricing. Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. 4517 Fax Pricing Local P1 Cash

Press Enter to change the Units price for the first page of a local Fax

Local P1 Cash .20


4517 Fax Pricing Local P2 Cash

Press Enter to change the Units price for each additional page of a local Fax

Local P2 Cash .10


4517 Fax Pricing L.D. P1 Cash

Press Enter to change the Units price for the first page of a long distance Fax

L.D. P1 Cash .20


4517 Fax Pricing L.D. P2 Cash

Press Enter to change the Units price for each additional page of a long distance Fax

L.D. P2 Cash .10


4517 Fax Pricing INTL P1 Cash

Press Enter to change the Units price for the first page of international Fax

INTL P1 Cash .20


4517 Fax Pricing INTL P2 Cash

Press Enter to change the Units price for each additional page of an international Fax

INTL P2 Cash .10


4517 Fax Pricing Local P1 Card

Press Enter to change the Card price for the first page of a local Fax

Local P1 Card .20



4517 Fax Pricing Local P2 Card

Press Enter to change the Card price for each additional page of a local Fax

Local P2 Card .10


4517 Fax Pricing L.D. P1 Card

Press Enter to change the Card price for the first page of a long distance Fax

L.D. P1 Card .20


4517 Fax Pricing L.D. P2 Card

Press Enter to change the Card price for each additional page of a long distance Fax

L.D. P2 Card .10


4517 Fax Pricing INTL P1 Card

Press Enter to change the Card price for the first page of international Fax

INTL P1 Card .20


4517 Fax Pricing INTL P2 Card

Press Enter to change the Card price for each additional page of an international Fax

INTL P2 Card .10


4517 Fax Pricing Local P1 Unit

Press Enter to change the Unit price for the first page of a local Fax

Local P1 Unit 1


4517 Fax Pricing Local P2 Unit

Press Enter to change the Unit price for each additional page of a local Fax

Local P2 Unit 1


4517 Fax Pricing L.D. P1 Unit

Press Enter to change the Unit price for the first page of a long distance Fax

L.D. P1 Unit 1


4517 Fax Pricing L.D. P2 Unit

Press Enter to change the Unit price for each additional page of a long distance Fax

L.D. P2 Unit 1



4517 Fax Pricing INTL P1 Unit

Press Enter to change the Unit price for the first page of international Fax

INTL P1 Unit 1


4517 Fax Pricing INTL P2 Unit

Press Enter to change the Unit price for each additional page of an international Fax

INTL P2 Unit 1


Press Menu to exit Fax Pricing Setup mode


Bonus Setup Mode The Bonus function can be used to encourage patrons to add larger values to the Units card by offering a “bonus” percentage on monies added to the card. There are 3 levels of bonus available based upon the value of money being added. NOTE: The bonus is determined by the Value added to the card during the session NOT the balance on the card Press the Menu button to move between Root Menus. Press Enter button to select the root menu. Press up or down to change settings. Pressing UP and Down at the same time will clear the current setting to Zero (or its Minimum value). Press Enter to select current setting and move to next menu. If the Keypad is connected the A button will move UP, the B button will move down, the D button will function as the Menu button, and numerical entries will be made directly via keypad. The Clear button will re-set and entry to default or its minimum value. Bonus Use Bonuses?

Press Enter to set the Pulse On time. This setting will only appear if the card reader is enabled in peripherals.

Use Bonuses No

Select Yes or No with the Up and Down then press Enter.

Bonus Bonus lvl 1

Press Enter to set the bonus level 1. This setting will only appear if the card reader is enabled in peripherals.

bonus lvl 1 $5.00

Set the level for bonus 1 to be applied with the Up and Down then press Enter.

Bonus Bonus1 % to add

Press Enter to set the bonus % for level 1. This setting will only appear if the card reader is enabled in peripherals.

bonus1 % to add 5

Set the % to add for bonus 1 with the Up and Down then press Enter.

When the deposited amount reaches the set level the corresponding percentage will be added to the card balance as a bonus. Bonus Bonus lvl 2


bonus lvl 2 $12.00




bonus2 % to add 7


When the deposited amount reaches the set level the corresponding percentage will be added to the card balance as a bonus.


Bonus Bonus lvl 3


bonus lvl 3 $20.00




bonus3 % to add 10


When the deposited amount reaches the set level the corresponding percentage will be added to the card balance as a bonus. Press Menu to exit Bonus Setup mode Diagnostics Mode Diagnostic mode was developed for production testing only and should not be used in the field.


Serial Printer Cable

ITC Part Number 901-06-91-91-NL Seiko DPU 414 Printer Settings Dip SW-1 Dip SW-2 Dip SW-3 1 (OFF) Input = Serial 1 (OFF) Printing Col. = 80 1 (ON) Data Length = 8 Bits 2 (ON) Print Speed = High 2 (ON) User Font = On 2 (ON) Parity Setting = NO 3 (OFF) Auto Loading = Off 3 (OFF) Character Select = Special 3 (ON) Parity Condition = Odd 4 (OFF) Auto LF = Off 4 (OFF) Zero = Slash 4 (OFF) Busy Control = Xon/Xoff 5 (ON) SettingCommand = Enable 5 (ON) International 5 (OFF) Baud 6 (OFF) Printing 6 (ON) Character 6 (ON) Rate 7 (ON) Density 7 (ON) Set 7 (ON) Select 8 (ON) = 100% 8 (OFF) = U.S.A. 8 (ON) = 9600bps

9D-SubMale

55400 toPrinter

GREEN

9D-SubMale

BLACK

GREENRED

2 33

BLACK

5

2

RED


Serial PC Cable

ITC Part Number 901-06-90-91 PC Serial Settings

Serial USB Cable To connect to a PC via USB a standard A to B type USB cable is used. USB Driver To use the USB connectivity a driver will need to be installed onto the PC. The appropriate Windows driver can be downloaded from http://www.ftdichip.com/FTDrivers.htm or contact ITC systems.

REDREDBLACK

GREEN

BLACK

9D-SubFemale

53

9D-SubMale

25400 to PC

532

GREEN


INSTALLATION Most photocopiers provide connection through a “Key Counter” or “Auditron” harness. The Coin Box enables the copier through the ENABLE Circuit of by closing a switch when sufficient credit is available. A voltage signal or relay contact closure signals the Coin Box that a copy has been produced through the PULSE circuit. If the copier does not have this circuitry available please contact ITC Systems Service department for other options. Placement of the Coin, Bill and Card Controller The Coin Box is designed to be mounted on or near the copier to be controlled. Different mounting brackets or stands can be provided by ITC Systems as an option. Mounting holes are located on the back (door) of the housing to secure it to the surface on which it is placed, i.e. adjacent wall or to the machine. The Coin Box should always be attached in a proper way for safety and security. Connecting to Power Power is supplied to the Controller by plugging the external Class 2, 24VAC transformer into a standard grounded 120 Volt wall outlet. The use of long extension cords or power bars is not recommended.


Copier Control Cable 901-10-45-52 Generic Copier Cable The Coin-op is shipped with the Generic copier cable unless a “Copier Specific” cable is ordered. The Generic cable comes with connectors to “Splice” onto the Copier’s Control Harness. Coin-op Interface Connector J6 “Connection to Copier”

BROWN

8

WHITE

12

3

BLUE

7

Enable 2 COM

ORANGE

Enable 2 N.O (N.C)

RED

6

Enable 1 COM

YELLOW

Enable 1 N.O.

#22 AWG X 9

5Enable 1 N.C.

Pulse 2 Signal

10

Pulse 2 Return

2

V+ Out 35mA Max

9 VIOLET

V- Out 35mA Max

GREEN

Pulse 1 Return

BLACK4

11

Pulse 1 Signal

1

Chassis Ground


Connection to the Copier Enable: The Enable is provided on the Black and White wires from the Coin-Op. This is a dry relay contact which is NORMALLY OPEN (open when disabled, closed when enabled). The relay is capable of switching ½ Amp at 60 Volts AC or DC. Typically, the Enable is attached to the copier Key Counter Plug by removing any jumper on the plug then attaching the Black wire to one side of the circuit and the White to the other side.

Pulse: The pulse is typically connected to the other 2 circuits on the Key Counter Plug. On most copiers, this will give 1 count per page printed (24vdc Pulse). Connect the Red to one wire of the Deduct circuit and the Brown to the other. Connection to Earth Ground IMPORTANT NOTE! The Green Ground wire on the Copier Harness is connected to the 5400 Chassis. This wire MUST be connected to the Copier Chassis or other Earth Ground for EMC and ESD shielding. Failure to connect this wire to Earth Ground could result in Interference with other electronic devices, Operational malfunction, and/or damage to the 5400. If the 5400 is used in an application where it is not connected to a Copier the chassis must still be connected to an earth ground. Contact ITC Systems Supportex department for assistance.

* NOTE: ThisDiagram is forgeneral referenceonly. The circuitpositions may notcorrespond to thecopier beingInstalled

"JUMPER"

KEY-COUNTERCONNECTOR

CUT JUMPEROR REMOVEPLUG

BLACK

WHITE

RED

BROWN


Alternate Connections: Using a Paper Clutch On some copiers, the Deduct pulse comes very late in the print cycle which may allow additional pages to be printed even though the credit is used up. To get around this, a common clutch (registration clutch for example) can be used for the billing pulse. Attach the Red wire to one side of the clutch and the Brown to the other.

The Deduct Pulse may also be taken off of the pick-up clutches for each tray using blocking diode as follows:

Note: Diodes are required (not supplied) (i.e. 1N4003 or equivalent). Diodes MUST be used to isolate the clutches, otherwise permanent damage may occur to the copier

Signal

REG Clutch

+24 Volts

PRICE 1 (RED)

PRICE 1 (BROWN)

+24 Volts

+24 Volts

Signal

1N4003

PRICE 1 (RED)

Signal

P/U Clutch 1

+24 Volts

Signal

PRICE 1 (BROWN)

P/U Clutch 3

1N4003

1N4003

P/U Clutch 2


Second Price (i.e. Large Paper) Connection: -“Line 2 LEVEL Mode” The Yellow and Violet wires on the interface plug are available to act as a “Shift to Price 2” input. When a voltage between 5 and 30 volts (AC or DC) is applied to this input, the Coin-Op will reflect the number of copies available to the second Price set in the parameters. Any Deduct Pulse received while this signal is active will change the second Price setting. Typically, the “Shift to Price 2” input is attached to an LED indicator that is lit when the larger paper cassette is being used.

INPUT 2 (VIOLET)

INPUT 2 (YELLOW)

LED


Second Price (i.e. Large Paper) Connection: -“Line 2 PULSE Mode” The Price 1 input is attached to each clutch to charge Price 1. The Price 2 input is attached to each clutch to charge Price 2.

Note: Diodes are required (not supplied) (i.e. 1N4003 or equivalent). Diodes MUST be used

to isolate the clutches, otherwise permanent damage may occur to the copier

1N4003

P/U Clutch 1

Signal

1N4003

Signal

Signal

+24 Volts

+24 Volts

1N4003

P/U Clutch 4

P/U Clutch 5

+24 Volts

+24 Volts

+24 Volts

PRICE 1 (RED)

1N4003

PRICE 2 (YELLOW)

PRICE 1 (BROWN)

PRICE 2 (VIOLET)

P/U Clutch 3

Signal

P/U Clutch 2

Signal

1N4003


Second Price (i.e. Large Paper) Connection: -“Line 2 PREMIUM Mode” The Price 1 input is attached to a common clutch (i.e. registration clutch) or signal (i.e. the Auditron or key counter port). The Price 2 input is attached to the paper tray clutch(es) that are to charge the Price 2 amount. Note: In this mode, when premium pages are printed, the Price 1 pulse immediately following the Price 2 pulse is ignored.

Note: Diodes are required (not supplied) (i.e. 1N4003 or equivalent). Diodes MUST be used

to isolate the clutches, otherwise permanent damage may occur to the copier

Signal

PremuimPaperClutch 2

+24 Volts

"Enable"

PremuimPaperClutch 1

+24 Volts

PRICE 1 (BROWN)

1N4003

Signal

Signal

OR REG ClutchPRICE 1 (RED)

"Pulse"

PRICE 2 (YELLOW)

+24 VoltsPRICE 2 (VIOLET)

PRICE 1 (BROWN)

1N4003

KEYCOUNTERConnector

PRICE 1 (RED)


Supply Voltage Orange and Blue A 15 Volt current limited supply is available for use with copiers that do not supply a deduct pulse but instead a contact closure, or transistor collector emitter path, when a copy is made. Xerox, OCE, and some Kodak copiers typically work in this fashion. Refer to the notes supplied with the copier to attach. Below is a typical connection as would be used on the Xerox bookmark 35 copiers.

"Pulse"

1N4003

BLUEWHITE

Copier Foreign Interf ace

DB15 FEMALE

815714613512411310291

RED

BROWN

ORANGE

"Enable"

5400 Custom Control Cable

DB15 MALE

8157

146

135

124

113

10291BLACK


Setup with Print Manager Connecting communication cable Connect a straight through male-female serial cable to COM 1 on the Coin Box (Top-Left-Corner). The other end is connected to COM1 or COM2 of the computer running Print Manager. Configuration of Print Manager Start Print Manger, click on Preferences button, then Readers button. Select “ITC Coin-Op ACT – Serial Interface” for Reader Identification. Set the Parity to “Odd”, Stop to “1”, Data to “8”, and Baud to “9600”. Select either Com1 or Com2 for Communication Port of the computer running Print Manager. The rest can use the default values. Refer to the manual that came with Print Manager for details. Set Coin Changer Return Escrow to Serial Control on the 5400


Connection to 4517 FAX Interface Connect the 4517 Fax Interface toCOM1 (External RS232) or COM4 (J14 on PCB) depending on the port selected in settings. The 4517 Fax Interface is powered separately from the Coin Op and must be plugged into an available AC outlet.

4517 Interface Cable

4517 Configuration Fax board firmware: CPU1- 4517_1 v3_5.inx CPU2- 4517_2 v3_2.inx Jumper on the fax board: JP12-3,4

1

9D-SubMale

4517 to 5400

Molex 522-01-305708-50-0117

GREEN

3BLACK

RED

2

REDBLACK

5GREEN

32

4517 Interface

Phone Jack

Fax Machine

AC Outlet

ITC Systems Coin Controller


Coin Changer Manual










Bill Acceptor Manual







Coinco BA30 Flash Codes

Flash codes 1-6 may appear during normal servicing of the BA30. To access flash codes 7-18, open bill box lid and remove power from the BA30 for 10seconds. Reapply power to BA30 with bill box lid open. Flash codes 7-18 will now appear for respective error or condition detected in the BA30. If more than one error or condition is exists, the lower number flash code will appear until its respective error or condition is corrected. The left and right sensors referenced below are given viewing the BA30 from the front. # of Flashes Description of Flash Codes 1 Bill box full 2 Bill box lid is open or bill box is off 3 Check bill path 4 All bill accept switches are off 5 Bill jam or sensor error 6 Stacker motor/home sensor 7 Transport motor/encoder sensor 8 Reserved for future use 9 EEPROM checksum error 10 RAM or ROM checksum error 11 Center optic sensor 12 Right optic sensor 13 Left optic sensor 14 Bill position sensor error 15 Right skew sensor 16 Left skew sensor 17 Lower board anti-pullback lever sensor 18 Upper board anti-pullback lever sensor


ITC SYSTEMS – WARRANTY AND LIABILITY CONTRACT By issuing a Purchase Order or contracting with ITC Systems to carry out the supply of products, clients are accepting the terms of this Warranty and Liability Contract. This document states the warranty and liability offered by ITC Systems on any products we manufacture or services we provide for our clients. ITC Systems shall not be liable for any direct, indirect and/or consequential damages or losses, including loss of use, revenue, profit incurred by the client, its customers and/or any third party as a result of the use of the work carried out by ITC Systems for the client, including any loss resulting from equipment failure or malfunctions, design or programming errors or any other use of the work carried out in this contract. The client specifically waives any claim or recourse it may have against ITC Systems in any of the above instances. When ITC Systems is manufacturing equipment, the equipment to be manufactured will be an exact replication of previously manufactured product, or the prototype, unless specified otherwise by the client, in writing. ITC Systems warrants all parts of new equipment for one year, from date of invoice or if warranty card is on file, from date on card, against DEFECTIVE MATERIAL OR WORKMANSHIP, but not against damage caused by accident, abuse, faulty installation, or improper operation. ITC Systems will repair, or at its option, replace without charge, F.O.B. factory, defective parts returned to its factory, transportation charges prepaid. ITC Systems’ obligation under this warranty is limited to repair or replacement as stated herein and does not include the return shipping charges. Any changes in design or improvements added to the line of equipment shall not create any obligation to install same on equipment previously sold and delivered to the client. Any unauthorized alteration of, or addition to, articles of the contractors manufacture voids this warranty. Equipment returned for Warranty repair must be accompanied by a copy of the Bill of Sale as verification of Purchase date. Equipment returned without a Bill of Sale will be charged to the customer at the normal repair rates.

Documents

OPERATION & SET-UP MANUAL - tracsystemshelpdesk.tracsystems.com/export/7508_ITC_Coin-OP 5400_USA_rev1_7.pdf · Using a Paper Clutch ... Coin Return Coin Slot COM1 Lock COM2 USB Bill