FLYWHEEL HORSEPOWER107 kW 143 HP @ 1950 rpm

OPERATING WEIGHT22710– 23260 kg

50,070 – 51,280 lb

BUCKET CAPACITY0.50–1.52 m3 0.65–2.0 yd3

Photo may include optional equipment.

HY

DR

AU

LIC

EX

CA

VA

TO

R

PC228USLC-3PC228USLC

WITH E.M.M.S

WALK-AROUNDWALK-AROUND

2

PC228USLC-3 Series Hydraulic Excavator

Working in congested or confined areas can be a challenge. Komatsu’s PC228USLC-3 SeriesHydraulic Excavators have a short tail swing profiledesigned specifically for work in confined areas. By reducing tail swing, thePC228USLC-3 can work in areas where conventional profile excavators wouldpose a safety risk. Perfect for work on roadways, bridge work, urban areas, oranywhere space is limited, the PC228USLC-3 provides you with performance andproductivity you expect from Komatsu equipment.

Larger cab● Komatsu’s low noise design

incorporates a fully pressed, highly-rigid cab that utilizes viscous cabmounting.

● A sliding convex door facilitateseasy entrance in confined areasand reduces the danger of beingdamaged on roadways becausethe door does not protrude whenopen.

● Komatsu’s large cab meets ISOworking space standards toprovide secure, safe, andcomfortable operation.

Wide working ranges● Maximum digging height of the

PC228USLC-3 is larger than that of thePC200LC-7. Raising the boom on thePC228USLC-3 to a wider angle enhancesoverall working performance. Job sitesthat require a long upper reach, such asdemolition and slope cutting benefitfrom the increased digging anddumping ranges of the PC228USLC-3.

High mobility● Large drawbar pull and steering force display

its ability when operating on a slope.

3

FLYWHEEL HORSEPOWER107 kW 143 HP @ 1950 rpm

OPERATING WEIGHT22710 – 23260 kg50,070 – 51,280 lb

BUCKET CAPACITY0.50 – 1.52 m3

0.65 – 2.0 yd3

PC228USLC-3HYDRAULIC EXCAVATOR

Photo may include optional equipment.

Komatsu’s highly productive, innovativetechnology, environmentally friendlymachines built for the 21st century.

Small road occupied widthKomatsu’s PC228USLC-3 occupies a roadwidth of 3.99 m 13'1" or less with a loadedbucket. This allows the machine to work oneither side of the lane without having to closeboth sides of the road.

Safe operationThe PC228USLC-3’s round form reduces the riskof hitting objects with the rear end of the machine.

High stabilityThe PC228USLC-3 offers exceptional lifting capacity and high stability with a large counterweight that requires no additional clearance.

Other features● Cup holder● Effortless joy stick● Internal storage with hot and cold box● Large capacity air conditioner● Sliding window

Multi-Function Color Monitor● Four working modes designed to match

engine speed, pump delivery, and systempressure

● Active mode for maximumproduction/power

● Breaker mode for optimum engine rpm,hydraulic flow, and pressure

● Economy mode for lower fuelconsumption and noise

● Lifting mode for high lifting capacity

PRODUCTIVITYFEATURES

PRODUCTIVITYFEATURES

4

PC200LC

180° swing width: 3.99 m 13'1"

3040 mm 10'0" 2750 mm 9'0"

2310 mm 7'7"

Protrusion from track:PC228USLC 770 mm 2'6"PC200LC 1500 mm 4'11"

Protrusion from track:PC228USLC 140 mm 5.5"PC200LC 1210 mm 4'0"

1680 mm 5'6"Implement swing radius

reduced by 730 mm 2'5"

Tail swing radius

reduced by 1070 mm

3'6"

Short implement swing radius:

2310 mm 7'7"—The Boom raising

angle of the PC228USLC-3

is larger than the PC200LC-7,

while front implement protrusion

is reduced.

Road and Bridge Work

Lane Width4.5 m 14'9"

3990

mm

13'1

"

Logging Road Work

Logging road widthapprox. 13'1" 4 m

Short tail swing radius:

1680 mm 5'6"— The reduced

tail swing of the PC228USLC-3

allows the machine to work in

more confined areas then a

conventional machine.

Working Mode Application Advantage

Active mode● Maximum production/power

A● Fast cycle times

E Economy mode ● Excellent fuel economy

L Lifting mode ● Hydraulic pressure isincreased by 7%

B Breaker ● Optimum engine rpm,operation hydraulic flow

5

PC228USLC-3HYDRAULIC EXCAVATOR

Excellent ProductivityEngine

The PC228USLC-3 gets its exceptional power and work

capacity from the Komatsu SAA6D102E engine. Output is

107 kW 143 HP, giving you increased hydraulic power while

improving fuel efficiency. The engine meets EPA emissions

regulations and noise levels have been reduced for greater

operator comfort.

Wider Working Ranges

Raising the boom on the PC228USLC-3 to a wider angle

enhances overall working performance.

Large Digging Force

The PC228USLC-3 has a large bucket digging force and arm

crowd force.

Forces using Power Max function:

Power Max Function

This function temporarily increases digging force for added

power in tough situations.

PC228USLC-3 PC200LC-7Maximum digging height 10700 mm 35'1" 10000 mm 32'10"Maximum digging depth 6620 mm 21'9" 6620 mm 21'9"Maximum digging reach 9875 mm 32'5" 9875 mm 32'5"

PC228USLC-3

Bucket digging force (ISO) 15200 kg149kN/33,500 lb

Arm crowd force (ISO) 11000 kg108kN/24,250 lb

High Stability

The PC228USLC-3 offers exceptional lifting capacity and

high stability with a large counterweight that requires no

additional clearance.

High Mobility

The PC228USLC-3 has 13% greater drawbar pull than the

PC200LC-7 and the automatic gear shifting function provides

improved mobility on uneven ground or slopes.

PC228USLC-3 PC200LC-7

Maximum drawbar pull 20600 kg 18200 kg202kN/45,410 lb 178kN/40,120 lb

Automatic Three-Speed Travel

Travel speed is automatically shifted from high to low speed according to the pressure of the travel.

Multi-Function Color MonitorA newly developed Multi-Function Color Monitor has multiplefunctions, such as Working mode selection, hydraulic pumpoil flow adjustment for matching to attachment, andmaintenance interval notice, etc.

Lifting Mode

When the Lifting mode isselected, lifting capacity isincreased by raising hydraulicpressure 7%.

Economy Mode

Economy mode isenvironmentally friendly. Fuelconsumption is reduced.

High Mid Low

Travel Speed5.5 km/h 4.1 km/h 3.0 km/h3.4 mph 2.5 mph 1.9 mph

Working Mode Selection

WORKINGENVIRONMENT

WORKINGENVIRONMENT

6

Operator’s CabMulti-Position Controls

The multi-position, pressure

proportional control levers allow

the operator to work in comfort

while maintaining precise control.

A double-slide mechanism allows

the seat and controllers to move

together or independently, allowing the

operator to position the controllers for

maximum productivity and comfort.

Cab Mount

The cab rests on viscous damping

mounts to reduce vibration and noise

from the machine body. The result is

reduced operator fatigue.

Noise

Komatsu’s low noise design

incorporates a fully pressed highly-rigid

cab that utilizes viscous cab mounting.

Sliding Convex Door

The sliding convex door facilitates

easy entrance in confined areas

while reducing the danger of being

damaged on roadways because the

door does not protrude when open.

The cab also features a sliding

window on the door.

Washable Floor

The PC228USLC-3’s floor is easy to

keep clean. The gently inclined surface

has a flanged floormat and drainage

holes to facilitate run-off.

The PC228USLC-3 cab interior is spacious and provides a comfortable working environment…

Large Capacity Air Conditioningand Heating Unit

The PC228USLC-3 air conditioner

capacity is 43% greater than the

PC228USLC-2. The bi-level controls

provide cool air to the operator’s head

and warm air to the feet allowing

comfort throughout the year. The

defroster function keeps the front glass

clear.Capacities

Cooling 6900 kcal 27,379 btuHeating 5200 kcal 20,634 btu

Skylight

Air conditioner and radio Joystick controls

Control panel

PC228USLC-3HYDRAULIC EXCAVATOR

7

8

1

4

2

3

5

1. E.M.M.S MONITOR

2. CONTROL LOCK

3. AM/FM RADIO

4. A/C HEATER

5. RETRACTABLESEAT BELT

6. THROTTLE CONTROL

7. HOT/COLD BOX

8. CUP HOLDER

7

6

MAINTENANCEFEATURES

MAINTENANCEFEATURES

8

Easy MaintenanceKomatsu designed the PC228USLC-3 to have easy service access. By doing so, routine maintenance and servicing are less

likely to be skipped, which can mean a reduction in costly downtime later on. Here are some of the many service features found

on the PC228USLC-3:

Optimum Maintenance Layout

Effortless access to engine-related maintenance items such as oil

filter, oil dipstick, coolant reserve tank, fuel filter, and air cleaner.

New Hydraulic Filter Element

The new hydraulic oil filter uses high performance filtering

material for long element replacement intervals, which

significantly reduces maintenance costs. The new hydraulic filter

extends the element replacement interval to 1000 hours and keeps

the hydraulic oil replacement interval at 5,000 hours. Its small size

reduces waste material.

1 2 11 10

7

6

9

8

1214

13

3

4

5 EnginePump

Central partition

Left rear side cover

Control valve

Hydraulic tank

Fuel tank

RadiatorOil cooler

Air-cooled aftercooler

Engine hood

Right rear side cover

Right front side cover

Comparison of Replacement Intervals unit: hours

PC228USLC-3 PC228USLC-2Engine oil 500 250Engine oil filter 500 250Hydraulic oil 5,000 5,000Hydraulic oil filter 1,000 500

Left rear side cover1. Cooling water reserve tank2. Air cleaner3. Battery4. Tool box5. Grease gun holder

Right rear side cover6. Engine oil filter*7. Water separator8. Oil fill port for PTO*9. Fuel drain valve*

Right front side cover10. Windshield washer tank

Central partition11. Oil filler for swing machinery

and oil level check pipe

Opening/Closing of engine hood12. Engine oil fill port13. Engine oil dip stick14. Fuel filter

*Remote maintenance items

9

PC228USLC-3HYDRAULIC EXCAVATOR

Long greasing Interval

Special material is used for the bushings of the work equipment to lengthen greasing

intervals. All bushing lubrication intervals of the work equipment, excluding the bucket

connection, are extended from 100 hours to 250 hours, reducing maintenance costs.

Safety Features

Side-by-Side Cooling

The oil cooler and aftercooler which

previously were installed in front of the

radiator are installed side by side. As a result,

it is very easy to clean the radiator, etc.

Removal and installation of the radiator and

oil cooler can now be done independently.

Water Separation

A Water Separator is standardequipment, removing water mixed in fueland preventing fuel system damage.

Steps with non-skid sheetsprovide improved footing formaintenance.

A Large handrail is installedto aid in getting on/off themachine safely.

EMMS (Equipment Management Monitoring System)

Monitor FunctionThe controller monitors engine oil level,coolant temperature, battery charge, airclogging, etc. If the controller finds anyabnormality, it is displayed.

Maintenance FunctionThe monitor informs replacement time ofoil and filters when the replacementinterval is reached.

Trouble Data Memory FunctionThe monitor stores abnormalities foreffective troubleshooting.

SPECIFICATIONSSPECIFICATIONS

10

UNDERCARRIAGE

Center frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-leg frameTrack frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Box-sectionSeal of track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sealed trackTrack adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HydraulicNumber of shoes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 each side Number of carrier rollers . . . . . . . . . . . . . . . . . . . . . . . . . 2 each sideNumber of track rollers . . . . . . . . . . . . . . . . . . . . . . . . . . 9 each side

COOLANT AND LUBRICANT

CAPACITY (REFILLING)

Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 ltr 84.5 U.S. galRadiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.4 ltr 5.9 U.S. galEngine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 ltr 6.3 U.S. galFinal drive, each side . . . . . . . . . . . . . . . . . . . . 5.2 ltr 1.4 U.S. galSwing drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6 ltr 1.7 U.S. galHydraulic tank . . . . . . . . . . . . . . . . . . . . . . . . 126 ltr 33.3 U.S. gal

ENGINE

Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Komatsu SAA6D102EType . . . . . . . . . . . . . . . . . . . . 4-cycle, water-cooled, direct injectionAspiration . . . . . . . . . . . . . . . . . . . Turbocharged and air aftercooledNumber of cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 mm 4.02"Stroke. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 mm 4.72"Piston displacement. . . . . . . . . . . . . . . . . . . . . . . . . . 5.88 ltr 359 in3

Flywheel horsepower . . . 107 kW 143 HP @ 1950 rpm (SAE J1349)Governor . . . . . . . . . . . . . . . . . . . . . . . . . . . . All-speed, mechanical

Meets 2001 EPA Tier 2 emission standards.

HYDRAULIC SYSTEM

Type . . . . . . . . . . . . . . . . . . . . . . HydrauMind (Hydraulic MechanicalIntelligence New Design) system

Closed-center system with load-sensing valves and pressure-compensated valves

Number of selectable working modes . . . . . . . . . . . . . . . . . . . . . . . 4Main pump . . . . . . . . . . . . . . . . . . . . . Variable-capacity piston pumpPumps for. . . . . . . . . . Boom, arm, bucket, swing, and travel circuitsMaximum flow . . . . . . . . . . . . . . . . . . . . . . . . . 428 ltr 113 U.S. gpmSupply for control circuit . . . . . . . . . . . . . . . . . . . Self-reducing valve

Hydraulic motors:Travel . . . . . . . . . . . . . . . 2 x axial piston motor with parking brakeSwing . . . . . . . . . . 1 x axial piston motor with swing holding brake

Relief valve setting:Implement circuits . . . . . . . . . . . . . . . . . . . 355 kg/cm2 5,050 psi(At power max. and lifting mode . . . . . . . . . 380 kg/cm2 5,400 psiTravel circuits . . . . . . . . . . . . . . . . . . . . . . . 380 kg/cm2 5,400 psiSwing circuits . . . . . . . . . . . . . . . . . . . . . . . 285 kg/cm2 4,050 psiPilot circuit . . . . . . . . . . . . . . . . . . . . . . . . . . 33 kg/cm2 470 psi

Hydraulic cylinders:Number of cylinders – bore x strokeBoom. . . . . . . . . . . . . . . . . 2 – 130 mm x 1385 mm 5.1" x 54.5"Arm . . . . . . . . . . . . . . . . . . 1 – 135 mm x 1490 mm 5.3" x 58.7"Bucket . . . . . . . . . . . . . . . . 1 – 115 mm x 1120 mm 4.5" x 44.1"

PC228USLC-3Triple Shoes Operating Weight Ground Pressure

mm in kg lb kPa kg/cm2 psi600 mm 24" 22710 50,070 48.0 0.48 6.83700 mm 28" 22979 50,660 41.2 0.42 5.97800 mm 31.5" 23260 51,280 36.3 0.37 5.26

SWING SYSTEM

Driven method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HydrostaticSwing reduction. . . . . . . . . . . . . . . . . . . . Planetary double reductionSwing circle lubrication . . . . . . . . . . . . . . . . . . . . . . . Grease-bathedSwing lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil disc brakeSwing speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.0 rpmSwing torque . . . . . . . . . . . . . . . . . . . . . . . . 6656 kg.m 48,124 ft lbs

OPERATING WEIGHT (APPROXIMATE)

Operating weight, including 5700 mm 18'8" one-piece boom, 2925mm 9'7" arm, SAE heaped 0.80 m3 1.05 yd3 backhoe bucket,operator, lubricant, coolant, full fuel tank, and the standard equipment.

DRIVES AND BRAKES

Steering control . . . . . . . . . . . . . . . . . . . . . . . . Two-lever with pedalsDrive method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HydrostaticTravel motor . . . . . . . . . . . . . . . . . Axial piston motor, in-shoe designReduction system . . . . . . . . . . . . . . . . . . Planetary double reductionMaximum drawbar pull . . . . . . . . . . . . . . . . . . . . 20600 kg 45,410 lbMaximum travel speed: High . . . . . . . . . . . . . . . . . 5.5 km/h 3.4 mph

Mid. . . . . . . . . . . . . . . . . . 4.1 km/h 2.5 mphLow . . . . . . . . . . . . . . . . . 3.0 km/h 1.9 mph

Service brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic lockParking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil disc brake

11

PC228USLC-3HYDRAULIC EXCAVATOR

WORKING RANGE AND BUCKET/ARM COMBINATION

PC228USLC-3Arm 2925 mm 9'7"

A Overall length 8890 mm 29'2"B Overall width 3080 mm 10'1"C Overall height (to top of cab)* 3010 mm 9'11"D Ground clearance, counterweight* 1060 mm 3'6"E Minimum ground clearance 440 mm 1'5"F Tail swing radius 1680 mm 5'6" G Length of track on ground 3640 mm 11'11"H Track length 4450 mm 14'7"I Track gauge 2380 mm 7'10"J Width of crawler 3080 mm 10'1" K Shoe width 700 mm 28"L Grouser height 26 mm 1"M Machine cab height* 2285 mm 7'6"N Upper structure width 2980 mm 9'9"O Distance, swing center to rear end 1680 mm 5'6"

Arm 2925 mm 9'7"

A Maximum digging height 10700 mm 35'1"

B Maximum dumping height 7825 mm 25'8"

C Maximum digging depth 6620 mm 21'9"

D Maximum vertical wall digging depth 5980 mm 19'7"

E Maximum digging depth of cut for 8' level 6370 mm 20'11"

F Maximum digging reach 9875 mm 32'5"

G Maximum digging reach at ground 9700 mm 31'10"

H Minimum swing radius 2310 mm 7'7"

I Maximum height at minimum swing radius 8250 mm 27'1"

Bucket digging force (ISO) 15200 kg/149kN/33,500 lb

Bucket digging force (SAE) 13700 kg/134kN/30,200 lb

Arm crowd force (ISO) 11000 kg/108kN/24,250 lb

Arm crowd force (SAE) 10700 kg/105kN/23,590 lb

DIMENSIONS

F

G

2440 8'

0

-1

-2

-3

-4

-5

-7

-8

-6

012345678910

5

6

7

8

9

11

10

1112(m)

1

2

3

4

(m)

C ED

AI B

H

AVAILABLE BUCKETS

Digging force at power maximum

A

F,O

M

D

GH

C

LK E

J

N

I

B

* Excluding grouser height

ArmBucket Capacity Width Outside Lip Weight Teeth 2.4 m 7'11" 2.9 m 9'7"

0.50 m3 0.66 yd3 610 mm 24" 639 kg 1,409 lb 3 V VKomatsu 0.67 m3 0.88 yd3 762 mm 30" 679 kg 1,496 lb 4 V V

“H” Series 0.86 m3 1.13 yd3 914 mm 36" 767 kg 1,690 lb 4 V VHD 1.04 m3 1.36 yd3 1067 mm 42" 842 kg 1,856 lb 5 V W

1.22 m3 1.59 yd3 1219 mm 48" 910 kg 2,007 lb 6 W X1.38 m3 1.80 yd3 1372 mm 48" 962 kg 2,121 lb 6 X Y1.53 m3 2.0 yd3 1524 mm 48" 1102 kg 2,430 lb 6 Y Z

V – Material weight up to 2.1 ton/m3 3,500 lb/yd3, W – Material weight up to 1.8 ton/m3 3,000 lb/yd3

X – Material weight up to 1.5 ton/m3 2,500 lb/yd3, Y – Material weight up to 1.2 ton/m3 2,000 lb/yd3, Z – Not useable

AESS626-00 ©2003 Komatsu Printed in USA DK07(5M)SFI 07/03(EV-2)

www.KomatsuAmerica.com Materials and specifications are subject to change without noticeis a trademark of Komatsu Ltd. Japan

440 N. Fairway Dr.,Vernon Hills, IL 60061

STANDARD EQUIPMENT

● Air cleaner, double element with auto dustevacuation

● Air conditioner/heater● Alternator, 60 A● Batteries, 110 Ah / 2 x 12 V● Boom holding valve● Cab which includes: AM/FM radio,

antenna, floormat, intermittent wiper and

washer, large ceiling hatch, pull-up frontwindow, openable rear window, removablelower windshield, sliding seat with 76 mm3" retractable seat belt, tinted safety glass

● Cooling fan, mixed flow with fan guard● Counterweight, 6050 kg 13,340 lb● Dustproof net for radiator and oil cooler● Instrument panel

● Light, one front● Pump/engine room partition cover● Shoes:—700 mm 28" triple grouser● Starting motor, 5.5 kW● Track guiding guards ● Travel alarm● Turbocharger exhaust manifold cover

● Arm—2400 mm 7'11" arm—2400 mm 7'11" arm with piping—2925 mm 9'7" arm—2925 mm 9'7" arm with piping

● Arm holding valve

● Boom —5700 mm 18'8" boom—5700 mm 18'8" boom with piping

● Hydraulic control unit—1 additional actuator—2 additional actuators

● Rain visor for cab

● Shoes 500 mm 20" road liner600 mm 24" triple grouser800 mm 31.5" triple grouser610 mm 24" flat860 mm 34" swamp

● Sun visor

OPTIONAL EQUIPMENT

PC228USLC-3 Shoe: 800 mm 31.5" Unit: kg lbA 3.0 m 10' 4.5 m 15' 6.0 m 20' 7.5 m 25' Maximum

B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs6.0 m *4850 kg 4450 kg *2700 kg *2700 kg

20' *10,700 lb 9,800 lb *6,000 lb *6,000 lb3.0 m *12800 kg 12650 kg *8400 kg 6800 kg *6800 kg 4250 kg 4800 kg 2950 kg *2900 kg 2300 kg

10' *28,300 lb 27,900 lb *18,500 lb 15,000 lb *15,000 lb 9,400 lb 10,500 lb 6,500 lb *6,300 lb 5,100 lb0.0 m *7900 kg *7900 kg *10500 kg 5950 kg 6800 kg 3850 kg 4750 kg 2750 kg *3650 kg 2300 kg

0' *17,500 lb *17,500 lb *23,100 lb 13,200 lb 14,900 lb 8,500 lb 10,500 lb 6,000 lb 8,000 lb 5,000 lb–3.0 m *16000 kg 11600 kg 10400 kg 5900 kg 6450 kg 3750 kg 5000 kg 3000 kg

–10' *35,300 lb 25,500 lb 22,900 lb 12,800 lb 14,200 lb 8,300 lb 11,000 lb 6,600 lb

PC228USLC-3 Shoe: 700 mm 28" Unit: kg lbA 3.0 m 10' 4.5 m 15' 6.0 m 20' 7.5 m 25' Maximum

B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs6.0 m *4850 kg 4400 kg *2700 kg *2700 kg

20' *10,700 lb 9,700 lb *6,000 lb 6,000 lb3.0 m *12800 kg 12500 kg *8400 kg 6700 kg *6800 kg 4200 kg 4750 kg 2900 kg *2900 kg 2250 kg

10' *28,300 lb 27,600 lb *18,500 lb 14,800 lb 15,000 lb 9,300 lb 10,400 lb 6,400 lb 6,300 lb 5,000 lb0.0 m *7900 kg *7900 kg 10350 kg 5900 kg 6700 kg 3800 kg 4700 kg 2700 kg *3650 kg 2250 kg

0' *17,500 lb *17,500 lb 22,800 lb 13,000 lb 14,700 lb 8,400 lb 10,400 lb 5,900 lb *8,000 lb 4,900 lb–3.0 m *16000 kg 11450 kg 10250 kg 5800 kg 6350 kg 3700 kg 4950 kg 2950 kg

–10' *35,300 lb 25,200 lb 22,600 lb 12,700 lb 14,000 lb 8,200 lb 10,900 lb 6,500 lb

LIFTING CAPACITY WITH LIFTING MODE ON MULTI-FUNCTION COLOR MONITOR

C

A

B

Equipment:● Arm: 2925 mm 9'7"● Boom: 5700 mm 18'8"● Bucket: 0.8 m3 1.05 yd3

A: Reach from swing centerB: Bucket hook heightC: Lifting capacityCf: Rating over frontCs: Rating over side

: Rating at maximum reach

* Load is limited by hydraulic capacity rather than tipping. Ratings are based on SAE Standard No. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.