Operating ManualHEADS UP DISPLAY

-1- -2-

-3- -4-

-5- -6-

Contents1. Introduction to the HUD

2. Unit Display & Functions

3. Installation process

4. Setting Modes

5. Installed program displays

6. Additional information

7. Product specifications

8. Contents

3

4

6

7

8

9

10

10

1. Introduction to the HUD

2. Unit Display & Functions

2-1 Unit Display

2-2 Button and interface functions

A. Power Switch B. Light SensorC. Micro USB Connection Port D. Scrolling Button

Scroll down: switch on to display multi-functionsScroll up: set warning for exceeding speedkm/h: 60 80 100 120 mph: 25 45 65 80(For choice, every time the button is scrolled down, the screen will display the current set-speed.)Press down the middle button lightly to switch between metric and imperial unit.

A. Digital display B. RPM display C. Battery voltage warning D. Speed unit E. Water temperature warning F. Engine check warning lightG. Setup status indicator

km/h: Kilometer per hour mph: Mile per hour C: Centigrade F: Fahrenheit V: Voltage

C

D

B

A

G

E F

1

2

3

DC

A

B

HUD is the common term used for "Head Up Display". The HUD allows the driver to see the vehicles essential dashboard data without looking away from the road.

This is a multifunctional product, developed specifically for the OBDII interfaceproviding stable performance, safe application and plug & play installation.

This HUD has been tested on a variety of vehicles with an OBDII interface and a 12V battery system manufactured after December 31, 2008. Please refer to your car's user manual before installation. The HUD is compatible with the OBDII interface which allows for "Plug & Play" installation without the need to modify your vehicles wiring.

The all-digital display will project the vehicles speed and engine rotation speed (RPM) directly onto the windscreen for direct viewing while driving. The HUD also includes an automatic power On/Off function as well as automatic brightness controlled by the built in ambient light sensor. All settings can be accessed by the built-in scroll button for easy one finger operation.

3. Installation process

3-1

3-2 Start the vehicles engine

3-3 Turn on the HUD

2-3 Detail drawing

A. Micro USB socket B. Scrolling button C. SpeakerD. Light Sensor E. Power switch F. Display Screen

A E

D

F

BC

DO NOT start the vehicle's engine before completing the HUD installation.

Connect the supplied cable to the HUD and the vehicles OBDII port ensuring the engine is switched off.

-7-

4. Setting Modes

-8-

Protocal detection and selection (0~8): Default value is 0. The protocol is automatically from 1 to 8, the valued display is the applicable protocol which is automatically selected.

Correction factor of vehicle speed (50~150): Default value is 108km/h. Please adjust it according to the actual condition.

Voltage warning setting (9~14): Default value is 11 Volt.

The opening time of buzzer (0~10 second): Default value is 0, ie in “mute” mode.

-11-

8. 7. Contents

9-1 HUD Display Module 9-2 Adhesive Mounting Pad9-3 Display Membrane9-4 Micro USB to OBDII cable9-5 User Manual

-12-

This product is guaranteed against defects for a period of 12 months from date of purchase. This warranty is provided by SRGS Pty Ltd ABN 23 113 230 050 (SupecheapAuto) of 751 Gympie Rd Lawnton QLD 4501 Ph (07) 3482 7500. Supercheap Auto will offer a repair, replacement product or store credit if the product is assessed as being defective during the warranty period.To claim under this warranty, take this product to the Front Service Desk of your nearest Supercheap Auto Store. For store locations, visit www.supercheapauto.com.au (AUS) or www.supercheapauto.co.nz (NZ). You will need your receipt or proof of purchase. Additional information may be requested of you to process your claim. Should you not be able to provide proof of purchase with a receipt or a bank statement, identification showing your name, address and signature may be required to process your claim. This product may need to be sent to the manufacturer to assess the defect before determining any claim. Faults or defects caused by product modification, misuse and abuse, normal wear and tear or failure to follow user instructions are not covered under this warranty. Our goods come with guarantees that cannot be excluded under the AustralianConsumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.Any expenses incurred relating to the return of this product to store will normally have to be paid by you. For more information contact your nearest Supercheap Auto store.The benefits to the consumer given by this warranty are in addition to other rights and remedies of the Australian Consumer Law in relation to the goods and services to which this warranty relates.

Water temperature alarm setting (90~130): Default value is 110 C.

-9- -10-

5. Installed program displays

5-1 After the installation of this HUD, turn on its power switch. The software version number will be displayed when you start the car engine.

5-2 OBDII Protocol detection

6. Additional Information

6-1 The information shown from the device is for reference only.6-2 Set-up device only when vehicle is turned off. 6-3 Do Not use a chemical cleanser on the panel to avoid damage.6-4 To protect the vehicle's battery, please turn off the power for long-term parking. 6-5 The micro USB to OBDII cable is for this product only. Don’t connect to other equipment.

5-3 Showing OBDII Protocol number detected after automatic detection

5-4 Officially launched: switch on the display by scrolling up the button.

Over speed warning (20~200): Default value is 80km/h.

Correction factor of trip distance (80~120): Default value is 104. Pleaseadjust it according to the actual condition.

Auto Power On/Off (1~2): Option 1 (Default) is suitable for 95% of vehicles.Option 2 is to be used on hybrid vehicles or vehicles with engine stop start technology.

4-1

4-2

4-3

4-4

4-5

4-6

4-7

4-8

While the unit is in the powered off position, roll and hold the scrolling button (refer figure 2-3) downwards and switch the power switch (refer figure 2-3) to the on position. The HUD will now enter the setting mode. Use the scrolling button up or down to select the desired setting and press in the scrolling button for “Enter” and “Save”. To exit the setting mode, simply switch the HUD off.