Operating instructions Washing machine€¦ · The washing machine is not suitable for outdoor use. It must only be used to wash garments which have been declared suitable for washing

Operating instructionsWashing machine

To avoid the risk of accidents or damage to the appliance, it is essentialto read these instructions before it is installed and used for the first time.

en-AU, NZ M.-Nr. 10 832 530

Caring for the environment

2

Disposal of the packingmaterialThe transport and protective packaginghas been selected from materials whichare environmentally friendly fordisposal, and can normally be recycled.

Recycling the packaging reduces theuse of raw materials in themanufacturing process and alsoreduces the amount of waste in landfillsites. Ensure that any plasticwrappings, bags etc. are disposed ofsafely and kept out of the reach ofbabies and young children. Danger ofsuffocation.

Disposing of your oldapplianceElectrical and electronic appliancesoften contain valuable materials. Theyalso contain specific materials,compounds and components, whichwere essential for their correct functionand safety. These could be hazardousto human health and to the environmentif disposed of with your domestic wasteor if handled incorrectly. Please do not,therefore, dispose of your old appliancewith your household waste.

Please dispose of it at your localcommunity waste collection / recyclingcentre for electrical and electronicappliances. You are also responsible fordeleting any personal data that may bestored on the appliance prior todisposal. Please ensure that your oldappliance poses no risk to childrenwhile being stored prior to disposal.

Contents

3

Caring for the environment .................................................................................. 2

Warning and Safety instructions ......................................................................... 6

Operating the washing machine ........................................................................ 13Control panel ......................................................................................................... 13How the control panel works ................................................................................ 14

Before using for the first time ............................................................................ 16Removing the protective foil and stickers ............................................................ 16

Washing environmentally and economically .................................................... 18

1. Preparing the laundry...................................................................................... 19

2. Loading the washing machine ....................................................................... 20

3. Selecting a programme .................................................................................. 21

4. Adding detergent............................................................................................. 23Detergent dispenser drawer .................................................................................. 23CapDosing............................................................................................................. 24

5. Starting the programme ................................................................................. 26

6. End of programme - unload the drum ........................................................... 27

Spinning................................................................................................................ 28

Delay start ............................................................................................................ 30

Programme chart ................................................................................................ 31

Extras.................................................................................................................... 34Short...................................................................................................................... 34Water plus ............................................................................................................. 34Pre-wash ............................................................................................................... 34Soak ...................................................................................................................... 34The following Extras can be selected in addition to the programme .................... 35

Programme sequence......................................................................................... 36

Changing the programme sequence ................................................................. 38Changing the programme ..................................................................................... 38Cancelling a programme ....................................................................................... 38Interrupting a programme...................................................................................... 38Adding or removing laundry .................................................................................. 39

Contents

4

Garment care label symbols............................................................................... 40

Detergent ............................................................................................................. 41The correct detergent............................................................................................ 41Detergent dispensing aids..................................................................................... 41Fabric softeners and liquid starch ......................................................................... 41Miele recommended detergents ........................................................................... 42

Cleaning and care ............................................................................................... 45External casing and fascia panel........................................................................... 45Cleaning the detergent dispenser drawer ............................................................. 45Cleaning the drum (Hygiene info) .......................................................................... 47Cleaning the water inlet filter ................................................................................. 47

Problem solving guide ........................................................................................ 48Problem solving guide........................................................................................... 48The programme does not start.............................................................................. 48The programme is cancelled and a fault indicator light lights up in the control panel.................................................................................................... 49During the programme, a symbol appears in the time display ............................. 50At the end of the programme, an indicator light lights up in the control panel ..... 50General problems with the washing machine ....................................................... 51An unsatisfactory wash result ............................................................................... 53The door will not open........................................................................................... 54Opening the door in the event of a blocked drain outlet and/or power cut .......... 55

Service.................................................................................................................. 57Contact in case of fault ......................................................................................... 57Optional accessories............................................................................................. 57Warranty ................................................................................................................ 57

Installation............................................................................................................ 58Front view .............................................................................................................. 58Rear view............................................................................................................... 59Installation surface ................................................................................................ 60Transporting the washing machine to its installation site...................................... 60Removing the transit bars ..................................................................................... 60Refitting the transit bars ........................................................................................ 62Levelling the machine............................................................................................ 63

Screwing out and adjusting the feet................................................................. 63Installing under a continuous worktop ............................................................. 64Washer and dryer stack ................................................................................... 64

Contents

5

The Miele water protection system ....................................................................... 65Connection to the water supply ............................................................................ 66Drainage ................................................................................................................ 67Electrical connection ............................................................................................ 68

Technical data...................................................................................................... 69

Consumption data ............................................................................................... 70Consumption data according to AS/NZS 2040.1 & AS/NZS 2040.2 .................... 70

Programmable functions .................................................................................... 72Choosing and selecting programmable functions ................................................ 72Editing and saving the programmable function .................................................... 73Exiting the programming level ............................................................................... 73 Keypad tone..................................................................................................... 73 PIN Code......................................................................................................... 74 Control panel standby status ......................................................................... 74 Memory .......................................................................................................... 75 Longer pre-wash Cottons .............................................................................. 75 Soak duration ................................................................................................. 75 Gentle action .................................................................................................. 75 Reduce temperature....................................................................................... 76 Water plus....................................................................................................... 76 Water plus level ............................................................................................... 76 Maximum rinse level ....................................................................................... 76 Suds cooling ................................................................................................... 77 Anti-crease ..................................................................................................... 77 Backlight brightness dimmed ........................................................................ 77

Optional accessories .......................................................................................... 78Detergent............................................................................................................... 78Specialist detergents............................................................................................. 79Fabric care............................................................................................................. 80Additives................................................................................................................ 80Machine care products.......................................................................................... 80

Warning and Safety instructions

6

This washing machine complies with all current local and nationalsafety requirements. However, inappropriate use can lead topersonal injury and damage to property.

Read the operating instructions carefully before using the washingmachine. They contain important information on safety,installation, use and maintenance of the appliance. This preventsboth personal injury and damage to the washing machine.

In accordance with standard IEC 60335-1, Miele expressly andstrongly advises that you read and follow the instructions in“Installation”, as well as in the “Warning and Safety instructions”.

Miele cannot be held liable for injury or damage caused by non-compliance with these instructions.

Keep these operating instructions in a safe place and pass themon to any future owner.

Correct application

This washing machine is designed for domestic use and for use insimilar environments by guests in hotel or motel rooms, bed &breakfasts and other typical living quarters. This does not includecommon/shared facilities or commercial facilities within hotels,motels or bed & breakfasts.

The washing machine is not suitable for outdoor use.

It must only be used to wash garments which have been declaredsuitable for washing by the manufacturer indicated on the garmentcare label. Any other use is not permitted. Miele cannot be heldliable for damage resulting from incorrect or improper use oroperation.


7

This washing machine is not intended for use by persons(including children) with reduced physical, sensory or mentalcapabilities, or lack of experience and knowledge, unless they havebeen given supervision or instruction concerning its use by a personresponsible for their safety.

Safety with children

Young children must not be allowed to use this appliance.

Older children may only use the appliance when its operation hasbeen clearly explained to them and they are able to use it safely,recognising the dangers of misuse.

Cleaning work may only be carried out by older children under thesupervision of an adult.

Please supervise children in the vicinity of the washing machineand do not let them play with it.

Technical safety

Please observe the instructions in “Installation” and “Technicaldata”.

Before setting up the washing machine, check it for any externallyvisible damage. Do not install or use a damaged machine.


8

Before connecting the washing machine, ensure that theconnection data on the data plate (fuse rating, voltage andfrequency) matches the mains electricity supply. If in any doubt,consult a qualified electrician.

Reliable and safe operation of this washing machine can only beassured if it has been connected to the mains electricity supply.

The electrical safety of this washing machine can only beguaranteed when continuity is complete between it and an effectiveearthing system which complies with current local and nationalsafety regulations. It is most important that this basic safetyrequirement is present and regularly tested and, where there is anydoubt, the household wiring system should be inspected by aqualified electrician. Miele cannot be held liable for theconsequences of an inadequate earthing system (e.g. electricshock).

Do not connect the washing machine to the mains electricitysupply by a multi-socket adapter, extension lead or similar. These donot guarantee the required safety of the machine (fire hazard due tothe risk of overheating).

Faulty components must only be replaced by genuine Miele spareparts. Miele can only guarantee the safety of the appliance whenMiele replacement parts are used.

The electrical socket must be easily accessible after installation sothat the machine can be disconnected from the electricity supply ifnecessary.


9

Unauthorised repairs could result in unforeseen dangers for theuser, for which Miele cannot accept liability. Repairs should only beundertaken by a Miele authorised service technician, otherwise anysubsequent damage will not be covered by the warranty.

If the connection cable is faulty, it must only be replaced by aMiele approved service technician to protect the user from danger.

In the event of a fault or for cleaning purposes, the washingmachine is only completely isolated from the electricity supply when:

– it is switched off at the wall socket and the plug is withdrawn, or

– it is switched off at the mains circuit breaker.

The machine must only be connected to the on-site water supplyusing a new hose kit. Old hose kits must not be re-used. Check thecondition of the hoses regularly so that you can replace them ingood time and avoid the risk of any water damage.

The water flow pressure must be at least 100 kPa and should notexceed 1000 kPa.

This washing machine must not be installed and operated inmobile installations (e.g. on a ship).

Do not make any alterations to the machine, unless authorised todo so by Miele.

In areas which may be subject to infestation by cockroaches orother vermin, pay particular attention to keeping the machine and itssurroundings in a clean condition at all times. Any damage whichmay be caused by cockroaches or other vermin will not be coveredby the machine warranty.


10

Correct use

Do not install the washing machine in a room where there is a riskof frost. Frozen hoses may burst or split. The reliability of theelectronic control unit may be impaired at temperatures belowfreezing point.

Before using the machine for the first time, check that the transitbars at the rear of the machine have been removed (see “Installation- Removing the transit bars”). During spinning, a transit bar which isstill in place may result in damage to both the machine and adjacentfurniture or appliances.

Turn off the tap if the machine is to be left for any length of time(e.g. holiday), especially if there is no floor drain (gully) in theimmediate vicinity.

Flooding danger. If hooking the drain hose into a wash basin, check that the water candrain off quickly enough to prevent the sink from overflowing. Makesure the drain hose is secure, so that the force of the water flowingout of the hose does not dislodge it.

Take care to ensure that foreign objects (e.g. nails, pins, coins,paper clips) do not find their way into the machine with the laundry.These may damage components of the machine (e.g. sudscontainer, drum), which in turn can result in damage to the laundry.

The maximum load for this washing machine is 7 kg (dry weight).See the “Programme chart” for the maximum recommended loadsfor individual programmes.


11

If the correct amount of detergent is dispensed, the machineshould not need to be descaled. If, however, you do wish to descaleit, only use a proprietary natural citric acid based descaling agent.Miele recommends using Miele descaler for washing machineswhich is available to order online at shop.miele.com (depending oncountry) or from Miele. Strictly observe the instructions on thepackaging.

Textiles which have been pre-treated in solvent based cleaningagents must be thoroughly rinsed in clean water before beingwashed in the machine.

Do not use solvent based cleaning agents, e.g. those containingbenzine, in this machine, as this may result in damage to componentparts and create toxic fumes. Such agents also pose a fire andexplosion hazard.

Do not use solvent based cleaning agents, e.g. those containingbenzine, to clean the external surfaces of the machine. They cancause damage to plastic surfaces.

Only use dyes specified by the manufacturer as being suitable foruse in a domestic washing machine. Always observe themanufacturer's instructions carefully.

Colour run and dye removers contain sulphur compounds whichcan cause damage such as corrosion. Do not use these products inthis machine.

If detergent comes into contact with the eyes, rinse themthoroughly with lukewarm water immediately. If swallowed, seekmedical assistance immediately and retain the packaging or label forreference. Those with skin problems or sensitive skin should avoidtheir skin coming into contact with detergent.


12

Accessories

Only use genuine Miele spare parts and accessories with thisappliance. If spare parts or accessories from other manufacturersare used, this will invalidate the warranty, and Miele cannot acceptliability.

A Miele tumble dryer can be stacked on top of a Miele washingmachine using the appropriate stacking kit (available as an optionalaccessory). Please make sure you order the correct one for the Mielewashing machine and Miele tumble dryer.

Miele cannot be held liable for damage caused by non-compliancewith these Warning and Safety instructions.

Operating the washing machine

13

Control panel

a Control panel

b Sensor controls – temperaturefor selecting the temperature.

c Sensor controls – spin speedfor selecting the spin speed.

d Sensor controls – Extrasvarious options can be added to thewash programmes.

e Indicator lights light up when necessary

f Sensor controls – CapDosing

g Time displayfor the programme duration

h Sensor controls for the Delay start function

i Start/Stop sensorfor programme start/cancellation

j Optical interfacefor service technicians

k Programme selectorfor selecting programmes and forswitching off. The washing machineis switched on by selecting aprogramme, and switched off byturning the programme selector tothe position.


14

How the control panel works

The , , , , and sensorsreact to fingertip contact. Selection ispossible as long as the respectivesensor is illuminated.

If a sensor is brightly lit, this means:currently selected

If a sensor is dimly lit, this means:selection possible

and sensors for temperatureand spin speed

After selecting a wash programme withthe programme selector, therecommended temperature (in °C) andspin speed (in rpm) light up brightly.

Selectable temperatures and spinspeeds light up dimly.

Sensor controls for Extras

You can select Extras to augment thewash programmes.

If a wash programme has beenselected, the sensor controls for thepossible Extras light up dimly.

Indicator lights

– lights up if there are faults with thewater inlet and drainage

– lights up if excess detergent wasused

– lights up as a reminder about hygieneinformation

– flashes for as long as it is possible toadd laundrylights up when the door of thewashing machine is locked

CapDosing

The CapDosing sensors are used foractivating cap dosing.

– Fabric care (e.g. fabric conditioner)

– Additives (e.g. detergent enhancers)

– Detergent (for the main wash only)


15

Time display

After the programme has started, theprogramme duration will appear in thedisplay in hours and minutes.

When Delay start is being used, theprogramme duration will appear afterthe Delay start time has elapsed.

Sensor controls

– After touching the sensor, a laterstart time for the programme (Delaystart) can be selected. Onceselected, lights up brightly.

– The duration of the Delay start periodis selected by touching the or sensor.

The Delay start time selected willappear in the time display.

After the programme has started, theDelay start time will begin to countdown.

Once the Delay start time has elapsed,the programme begins and theestimated programme duration appearsin the time display.

Start/Stop sensor

Touching the Start/Stop sensor startsthe selected programme or cancels aprogramme that has already beenstarted. The sensor flashes slowly assoon as it is possible for a programmeto be started and then lights upconstantly after the programme hasstarted.

Before using for the first time

16

Damage resulting from incorrectinstallation and connection.Installing and connecting thewashing machine incorrectly willcause serious damage to property.See “Installation”.

Removing the protective foiland stickers Remove:

– the protective foil from the door

– any stickers from the front and the lid

Please do not remove any labels(e.g. the data plate) which are visiblewhen you open the door.

Remove the drain hose elbowfrom the drumAn elbow piece for the drain hose isstored in the drum.

Reach under the door grip and pullthe door open.

Remove the elbow piece.

Shut the door with a gentle swing.

This washing machine has undergonea complete functional test at thefactory and there will be some residualwater in the drum from this process.

For safety reasons, spinning is notpossible until the machine has beenprepared for using for the first time. Toactivate the spinning function, you mustrun a wash programme without laundryand without detergent.

Using detergent could result in anexcessive build-up of foam.

This also activates the ball valve. Theball valve prevents detergent escapingfrom the suds container into the sumpduring a wash programme, thus makingmaximum use of the detergent.

Before using for the first time

17

Running the first programme Turn on the tap.

Turn the programme selector toCottons.

The washing machine is now switchedon and in the control panel, thetemperature 60°C lights up.

Touch the Start/Stop sensor.

The programme will start and the symbol lights up in the control panel.

After 10 minutes, the indicators dimand the Start/Stop sensor lights upconstantly.

After the end of the programme

At the end of the programme, the Anti-crease function is switched on. The symbol lights up in the control panel;: appears in the time display andthe drum occasionally rotates.


The door will be unlocked.


When the programme has ended,turn the programme selector to .

The washing machine is switched offand is now ready for use.

Useful tip: For safety reasons close thedoor. Otherwise there is a danger ofobjects being placed inadvertently inthe drum. If these remain unnoticed andwere washed in the next load, theycould damage the laundry. An opendoor is also a danger to pets andchildren.

Energy savings

– 10 minutes after the beginning of theanti-crease phase, the indicators dimand the Start/Stop sensor startsflashing.

– 15 minutes after completion of theanti-crease phase, the washingmachine switches off completely andthe door lock is released.

Washing environmentally and economically

18

Energy and water consumption

– To get the most out of your machine,load the maximum dry load for theprogramme you are using.The energy and water consumptionwill be the lowest in relation to thesize of the load.

– When smaller amounts of laundry arewashed, the Auto load control systemwill reduce the amount of water andenergy used.

– Use the Express 20 programme forsmall, lightly soiled loads.

– Modern detergents make it possibleto wash at lower temperatures (e.g.20°C). Using lower temperaturesettings will save energy.

– To maintain the hygiene of themachine, carry out a hot wash (above60°C) at regular intervals. The indicator will come on to remind youto carry out a hot wash.

Detergent consumption

– Do not exceed the amounts ofdetergent recommended by themanufacturer on the packaging.

– Adjust the dosage to the degree ofsoiling of the laundry.

– Reduce the amount of detergent withsmaller loads (approx. ⅓ less thanthe amount recommended can beused when washing a half load).

Choosing the correct Extra option(Short, Soak, Pre-wash)

Select:

– a wash programme together with theShort Extra option for light tomoderate soiling where there are noobvious marks.

– a wash programme without any Extraoptions for moderate to heavy soilingwith visible staining.

– a wash programme together with theSoak Extra option for heavily soiledlaundry.

– the Pre-wash Extra option for laundrywith large amounts of dirt (e.g. dust,sand).

When drying with a tumble dryer

Selecting the highest possible spinspeed for the wash programme willsave energy when drying in a tumbledryer afterwards.

1. Preparing the laundry

19

Empty all pockets.

Damage due to foreign objects.Nails, coins, paper clips, and so oncan cause damage to garments andcomponents in the machine.Check the laundry before washingand remove any foreign objects.

Sorting the laundry

Sort the laundry by colour and bycare label. Most garments have atextile care label in the collar or sideseam.

Useful tip: Dark textiles often containexcess dye and should be washedseparately several times before beingincluded in a mixed load. Always washwhite and coloured items separately.

Pre-treating stains

Badly soiled areas and stains shouldbe cleaned as soon as possible,preferably whilst still fresh. Spillagesshould be carefully dabbed off usinga soft, colourfast cloth. Do not rub.

Useful tip: Please refer to the Mielewebsite or Miele@mobile App for moreinformation on stain removal.

Damage due to solvent-basedcleaning agents.Cleaning agents containing benzine,stain remover, etc., can damageplastic parts.When pre-treating garments, makesure that any plastic parts (e.g.buttons) do not come into contactwith cleaning agent.

Risk of explosion due to solvent-based cleaning agents.If solvent-based cleaning agents areused, an explosive mixture can form.Never use solvent-based cleaningagents in the washing machine.

General tips

– Curtains: Remove lead weights firstor place in a laundry bag.

– Underwiring and collar stiffeners: Anyloose wiring in bras, shirt collarstiffeners, etc. should be removed orsewn in.

– Close any zips, attach velcrofasteners, fasten hooks and eyes etc.before washing.

– Fasten duvet covers and pillow casesto prevent small items from beingrolled up inside them.

Do not wash any items in this machinewhich are specified by the manufactureras not washable on the care label (symbol).

2. Loading the washing machine

20

Opening the door


Check the drum for pets or foreignobjects before loading it withlaundry.

The most efficient use of energy andwater is achieved when a full load iswashed. However, do not overload asthis reduces cleaning efficiency andcauses creases.

Unfold the laundry and load loosely inthe drum.

Mixing both large and small itemsgives better wash results and alsohelps distribute the load evenly duringspinning.

Useful tip: Please note the maximumload for the different wash programmes.

Closing the door

Make sure that no items are caughtbetween the door and the seal.

Shut the door with a gentle swing.

3. Selecting a programme

21

Programme selectionThe washing machine is switched on byturning the programme selector to awash programme.

Turn the programme selector to therequired programme.

The likely wash time is shown in thetime display and the pre-settemperature and spin speed light up inthe control panel.

Selecting the temperature and spinspeed

The wash programme's pre-settemperature and spin speed light upbrightly. The choice of temperaturesand spin speeds selectable for thewash programme light up dimly.

The temperatures reached in thewashing machine may differ from theselected temperatures. Thecombination of energy input andwashing time achieves an optimumwashing result.

Touch the sensor for the temperatureyou want. It then lights up brightly.

Touch the sensor for the spin speedyou want. It then lights up brightly.

3. Selecting a programme

22

Selecting Extras

The selection of Extras available forthe wash programme lights up dimly.

Touch the sensor for the Extra youwant. It then lights up brightly.

Useful tip: You can select multipleExtras for a wash programme.

Please refer to “Extras” for moreinformation.

4. Adding detergent

23

Detergent dispenser drawerAny detergent suitable for automaticfront loading washing machines can beused with this appliance. Pleaseobserve the instructions for use anddosage on the detergent packaging.

Tips on dosing

Adjust the detergent dosage to the levelof soiling of the laundry and the size ofthe load. Reduce the amount ofdetergent with smaller loads (e.g.reduce the amount of detergent by ⅓when washing a half load).

Too little detergent results in:

– laundry not getting properly cleanand with time it may become greyand hard to the touch.

– a build-up of mould in the washingmachine.

– grease not being completely removedfrom the laundry.

– limescale deposits on the heaterelements.

Too much detergent results in:

– poor wash, rinse, and spin results.

– a higher water consumption as anextra rinse cycle is automaticallyactivated.

– a greater burden on the environment.

Filling with detergent

Pull out the detergent drawer and adddetergents to the compartments.

Detergent for the pre-wash (dividethe total recommended amount asfollows: add ⅓ to compartment and ⅔ to compartment )

Detergent for the main wash andsoaking

Fabric softener, liquid starch, orcapsules

See “Detergent” for further information.

4. Adding detergent

24

CapDosingThree different types of capsule areavailable:

= Fabric care (e.g. fabricsoftener)

= Additives (e.g. detergentenhancers)

= Detergent (for the main washonly)

Each capsule contains the correctamount for one wash cycle.

You can order the capsules online atshop.miele.com (depending on country)or from Miele (see the end of thisbooklet for contact details).

Sie können die Caps über den MieleWebshop, den Miele Werkkundendienstoder Ihren Miele Fachhändler beziehen.

Capsules pose a health risk.The ingredients of capsules can behazardous to health if they areswallowed or come into contact withskin.Keep capsules out of the reach ofchildren.

Activating CapDosing Touch the sensor for the capsule you

want to use.

Sensor Capsule

for

for

for

Inserting a capsule Open the detergent dispenser drawer.

Open the lid of the /compartment.

Press the capsule in firmly.

https://shop.miele.de

https://shop.miele.de

4. Adding detergent

25

Close the lid and press it firmly shut.

Close the detergent dispenserdrawer.

The capsule is opened by the act ofinserting it in the detergent dispenserdrawer. The contents can run out ofthe capsule if you then remove itfrom the drawer before it is used.Dispose of opened capsules.

The wash programme will dispense thecontents of the capsule at the correcttime.

Water intake to the compartmentis solely via the capsule.Do not add any additional fabricsoftener to the compartment.

Remove the empty capsule at theend of the programme.

For technical reasons a small amountof water will remain in the capsule.

Deactivating/ChangingCapDosing In order to switch off CapDosing,

touch the brightly lit sensor.

In order to change CapDosing, touchone of the other capsule sensors.

5. Starting the programme

26

Starting the programme Touch the flashing Start/Stop sensor.

The door will lock and the programmewill start.

– As long as the symbol is flashingin the control panel you can addlaundry.

– When the symbol lights upconstantly, the door is locked untilthe end of the programme.

If a Delay start time has been selected,it will count down in the time display. Atthe end of the Delay start time orimmediately after the programme hasstarted (if no Delay start time has beenselected), the programme duration willappear in the time display.

Energy savings

After 10 minutes, if a programme hasnot been started or a sensor has notbeen touched, the indicators will dim.The Start/Stop sensor flashes slowly.

You can reactivate the indicators:

To do this, touch the Start/Stopsensor (this does not have any effecton a running programme).

6. End of programme - unload the drum

27

At the end of the programmeThe time display shows 0:00. The symbol will remain lit up in the controlpanel. The door is locked in the anti-crease phase.


The door will unlock and the symbol in the control panel goes out.

Pull open the door.

Remove the laundry.

Energy savings

– 10 minutes after the beginning of theanti-crease phase, the indicators dimand the Start/Stop sensor startsflashing.

– 15 minutes after completion of theanti-crease phase, the washingmachine switches off completely andthe door lock is released.

Items left in the drum could discolourother items in the next wash orbecome discoloured themselves.Check that all items have beenremoved from the drum.

Check the folds in the door seal forany small articles, e.g. buttons, whichmight be lodged there.

Turn the programme selector to the position. This switches the washingmachine off.

If applicable, remove the usedcapsule from the detergent dispenserdrawer.

Useful tip: Leave the detergentdispenser drawer slightly open to allowit to dry. Close the door of the washingmachine.

Spinning

28

Final spin speed

Programme Max. possiblerpm

Cottons 1400

Cottons 1400

Minimum iron 1200

Delicates 900

Woollens 1200*

Shirts 900

Express 20 1200

Dark garments/Denim 1200

Outerwear 900

Proofing 1200

Drain/Spin 1400

Separate rinse/Starch 1200

Final spin speed in theprogrammeWhen a programme is selected, thesensor for the optimum spin speed forthat programme will be brightly lit up inthe control panel. For programmesmarked with a * in the chart, theoptimum spin speed is not themaximum spin speed.

You can reduce the final spin speed or,depending on the programme, increaseit.

However, you cannot select a final spinspeed higher than that shown in thechart.

Rinse and interim spinThere is a spin after the main wash andbetween the rinses. A reduction in thefinal spin speed will also reduce theinterim spin speed. If a spin speed ofless than 700 rpm is selected for theCottons programme, an additional rinseis introduced.

Spinning

29

Omitting the final spin (Rinsehold) Touch the sensor (Rinse hold).

The laundry is not spun after the finalrinse and remains in the rinse water.This helps prevent creasing if thelaundry is not going to be removed fromthe drum immediately after the end ofthe programme.

After the end of a programme

The sensor for the optimum spinspeed lights up in the control panel.You can change the spin speed. TheStart/Stop sensor will light up,flashing.

Start the final spin:touch the flashing Start/Stop sensoronce.

The final spin is carried out.

End the programme:touch the flashing Start/Stop sensortwice.

The water will be pumped away.

Omitting rinse and interim spinand the final spin Touch the sensor.

After the last rinse, the water will bepumped away and the anti-creasephase will switch on.

In some programmes an additional rinseis introduced with this setting.

Delay start

30

With Delay start you can delay the startof a programme from 30 minutes up toa maximum of 24 hours. This allowsyou to make use of night-time economyelectricity rates, for example.

Selecting Delay start

Delay start cannot be selected withDrain/Spin or Proofing.

Select the programme required.

Touch the sensor.

The sensor lights up brightly.

Touch the or sensor repeatedlyuntil the required delayed start timeappears in the time display.

– For less than 10 hours, the Delaystart time changes in increments of30 minutes

– For more than 10 hours, the Delaystart time changes in increments of 1hour

Starting Delay start

Touch the flashing Start/Stop sensor.

The Delay start process starts andcounts down in the time display.

Altering Delay start


The Delay start process stops and the symbol in the control panel goes out.

Touch the or sensor repeatedlyuntil the required delayed start timeappears in the time display.

Touch the flashing Start/Stop sensor.

To cancel a Delay start that hasalready started


The Delay start process stops and the symbol in the control panel goes out.

Touch the brightly lit sensor.

Delay start is cancelled and the sensor goes out. The programmeduration appears in the time display.

Touch the flashing Start/Stop sensorin order to start the wash programme.

Programme chart

31

Cottons 60°C Max. load 7.0 kg

Items Cottons, linens or cotton mix fabrics, e.g. table linen, towelling,underwear, T-shirts etc.

Note With 60°C the actual wash temperature reached will be lower than60°C although the wash performance is the same as with thestandard Cottons 60°C programme.

Cottons 40°C Max. load 7.0 kg

Items Normally soiled cotton garments

Note These settings are the most efficient in terms of energy and waterconsumption for washing cottons.

Energy labelling programme according to AS/NZS 2040.1 & AS/NZS 2040.2

Cottons Cold to 90°C Max. load 7.0 kg

Items Cottons, linens or cotton mix fabrics, e.g. table linen, towelling,underwear, T-shirts etc.

Note The settings 60°/40°C differ from / as follows:

– Shorter programme durations

– Longer temperature holding times

– Higher energy consumption

Where particularly high levels of hygiene are required, please selecta temperature of 60°C or higher.

Minimum iron Cold to 60°C Max. load 3.5 kg

Items Synthetic, mixed fibre and easy care cotton

Note Reduce the spin speed for fabrics which crease easily.

Programme chart

32

Delicates Cold to 40℃ Max. load 2.0 kg

Items Delicate garments made from synthetic fibre, mixed fibre, rayon andviscose.

Curtains, including net curtains, specified as machine-washable bythe manufacturer.

Notes – Dust in curtains usually makes using a programme with a pre-wash advisable.

– For items which crease easily, deselect the spin.

Woollens Cold to 40°C Max. load 2.0 kg

Items Machine-washable or hand-washable wool or wool blend fabric. Ifthe care label does not specify a temperature, wash using the coldsetting.

Notes Reduce the spin speed for items which crease easily.

Shirts Cold to 60°C Max. load 2.0 kg

Items Shirts and blouses made of cotton and mixed fibre

Notes – Pre-treat collars and cuffs if necessary.

– Wash silk shirts and blouses in the Delicates programme.

Express 20 Cold to 40°C Max. load 3.5 kg

Items Cotton garments that have hardly been worn or are only very lightlysoiled.

Note The Short Extra is activated automatically.

Darks / Denim Cold to 60°C Max. load 3.0 kg

Items Black and dark garments made from cotton, mixed fibres anddenim.

Notes – Wash inside out.

– Denim often contains excess dye and may run during the first fewwashes. Wash light and dark coloured items separately.

Programme chart

33

Outerwear Cold to 40°C Max. load 2.5 kg

Items Performance outerwear (e.g. jackets and trousers) made frommembrane fabric such as Gore-Tex®, SYMPATEX®,WINDSTOPPER® etc.

Notes – Zip up or close jackets before washing.

– Do not use fabric softener.

– If required, these garments can also be re-proofed using theProofing programme. Proofing should not be done every time thegarment is washed.

Proofing 40°C Max. load 2.5 kg

Items Treating microfibre fabric, skiwear and table linen made from mainlysynthetic fibres to provide a water and dirt resistant finish.

Notes – The items should be freshly laundered and spun or dried beforeproofing.

– For best results, the items should be heat-treated afterwards eitherin a tumble dryer or by ironing.

Drain/Spin –

Notes – Drain only: Select for the spin speed.

– Make sure you select the appropriate spin speed.

Separate rinse/Starch Max. load 7.0 kg

Items – For rinsing hand-washed items.

– Starching table cloths, serviettes and workwear.

Notes – Reduce the spin speed for items which crease easily.

– Laundry that is to be starched should be washed but not treatedwith fabric softener.

– Items will be rinsed very effectively with two rinses by activatingthe Water plus Extra.

Extras

34

You can use the Extras sensors toaugment the wash programmes.

Extras are selected and deselectedusing the relevant sensors on thecontrol panel.

Touch the sensor for the Extra youwant.

The relevant sensor will light up brightly.

Not all the Extras can be used withevery programme.

An Extra that is not permitted for thewash programme is not lit dimly andcannot be activated by touch.

ShortFor light soiling with no visible staining.

The wash duration is reduced.

Water plusThe water level in the wash and rinsestages is increased and a second rinseis carried out in the “Separate rinse/Starch” programme.

You can select other functions for theWater plus sensor. These are describedin “Programmable functions”.

Pre-washFor laundry with large amounts of dirt,e.g. dust and sand.

SoakFor heavily soiled and stained itemswith protein stains.

– A duration of between 30 minutesand two hours can be programmed in30-minute increments for the soakprocess.

– The factory default setting is30 minutes.

See “Programmable functions - Soakduration” for instructions on how toprogramme a different soak period.

Extras

35

The following Extras can be selected in addition to theprogrammeThese Extras cannot be selected with programmes which are not listed in thechart below.

Sho

rt

Wat

er p

lus

Pre

-was

h

Soa

k

Cottons X X X X

Cottons X X X X

Minimum iron X X X X

Delicates X X X X

Shirts X X X X

Express 20 X1) – – –

Dark garments/Denim X X X X

Outerwear X X X X

Separate rinse/Starch – X – –

X = Can be selected 1) = Can be deselected

– = Cannot be selected

Programme sequence

36

Main wash Rinse Spin

Waterlevel

Washrhythm

Waterlevel

Rinses

Cottons 2-52)3)

Cottons 2-51)2)3)

Minimum iron 2-42)3)

Delicates 2-42)3)

Woollens 2

Shirts 3-43)

Express 20 1

Darks / Denim 3-52)3)

Outerwear 3-43)

Proofing – 1

Drain/Spin – – – –

Separate rinse / Starch 0-15)

Please see the next page for a description of the symbols.

Programme sequence

37

= Low water level

= Medium water level

= High water level

= Intensive rhythm

= Normal rhythm

= Sensitive rhythm

= Ultra sensitive rhythm

= Handwash rhythm

= Carried out

– = Not carried out

The washing machine has fullyelectronic controls with automatic loadrecognition. It takes in the right amountof water required for the programmedepending on the amount of laundryand its absorbency rate.

The programme sequences outlined inthe chart are based on the basicprogramme with a full load.

Special features in theprogramme sequenceAnti-crease:At the end of the programme the drumcontinues to turn at intervals for up to30 minutes to help prevent creasing.Exception: there is no anti-creasephase in the Woollens programme.The door can be opened at any timeduring the anti-crease phase.1) If a temperature of 60°C or higher is

selected and with 40°C and60°C two rinses are carried out.If a temperature of less than 60°C isselected, three rinses are carried out.

2) An additional rinse is carried out if:

– there is too much foam in the drum

– a spin speed lower than 700 rpm hasbeen selected.

3) An additional rinse is carried out if:

– Water plus has been selected and theoptions or have been activatedin Programmable functions.

5) An additional rinse is carried out if:the Water plus Extra is selected.

Changing the programme sequence

38

Changing the programmeIt is not possible to change theprogramme, the temperature, the spinspeed or the selected Extras after theprogramme has started.

Cancelling a programmeYou can cancel a programme at anytime after it has started.

Touch and hold the Start/Stop sensoruntil the time display switches to:.

The water will be pumped away. Assoon as the symbol in the controlpanel goes out, the programme hasbeen cancelled and the door can beopened.

Open the door.

Selecting a different programme aftercancelling the programme

Close the door.

Check that there is still detergent inthe dispenser drawer. Add moredetergent if necessary.

Turn the programme selector to theprogramme you want and start it bytouching the Start/Stop sensor.

Removing laundry after cancellingthe programme

If you want to remove the laundry whenit is dripping wet:

Open the door.

Remove the laundry.

If you want to remove the laundry afterit has been spun (damp):

Open the door.

Close the door.

Turn the programme selector toDrain/Spin.

Useful tip: Select an appropriate spinspeed.

Touch the Start/Stop sensor. Thelaundry is spun and can be removedafter spinning.

Interrupting a programme Turn the programme selector to the

position.

The washing machine switches off.

To continue: turn the programmeselector to the position of the washprogramme that was started.

Useful tip: If appears in the timedisplay, the programme selector is inthe incorrect position.

Changing the programme sequence

39

Adding or removing laundry

You can add or remove laundry at thestart of a wash programme as long asthe symbol is flashing in the controlpanel.

Briefly touch the Start/Stop sensor.

The programme will stop and the doorwill unlock.

Pull open the door.

Add or remove items.

Close the door.


The wash programme will continue.

Garment care label symbols

40

Washing

The figure quoted in the symbol is themaximum temperature at which thegarment can be washed. The numberof bars under the symbol indicates thelevel of agitation permitted.

No bar under the symbol =normal agitation

One bar under the symbol =reduced agitation

Two bars under the symbol =much reduced agitation

Hand wash (If no temperature isspecified, use the lowesttemperature or cold)

Do not wash

Programme selection examples

Programme Garment care labelsymbols

Cottons

Minimum iron

Delicates

Woollens

Express 20

Drying

The number of dots indicates thedrying temperature.

Normal temperature

Low temperature

Do not tumble dry

Ironing

The number of dots indicates theironing temperature.

approx. 200℃

approx. 150℃

approx. 110℃Do not steam iron garmentscarrying this symbol as thiscould cause irreversibledamage.

Do not iron

Professional cleaning

Dry clean only. The lettersindicate the type of cleaningagent required.

Professional Wet Clean only

Do not dry clean

Bleaching

Any oxidising bleaching agentcan be used

Only use an oxygen basedbleach or a non-chlorine bleach

Do not bleach

Detergent

41

The correct detergentAll detergents produced for automaticfront loading washing machines aresuitable. Follow the manufacturer'sinstructions and dosagerecommendations on the packaging.

The right amount to dispensewill depend on the following:– The soiling level of the laundry.

– The quantity of laundry.

– The water hardness level. Check withyour local water authority if you donot know the water hardness level inyour area.

Detergent dispensing aidsUse dispensing aids (e.g. balls) if theseare supplied with the detergent,particularly when using liquid detergent.

Refill packs of detergentWhen purchasing detergent, buy refillpacks wherever possible. This helpsreduce the amount of waste packaging.

Fabric softeners and liquidstarchFabric softeners make garments soft to handle and helpprevent static cling when tumble drying.

Fabric shapers are synthetic starches and give an evenstiffer hold.

Starch stiffens and gives body to items oflaundry, e.g. shirts, tablecloths and bedlinen.

Detergent

42

Miele recommended detergentsMiele detergents and care products have been specially designed for Mielewashing machines. They are available to order via the internet at shop.miele.com(depending on country) or from Miele.

MieleUltraWhite

MieleUltraColor

MieleCap

MieleCap

MieleCap

Cottons – Cottons – Minimum iron – – Delicates – –

Woollens – – – –

Shirts – Express 20 – – –

Dark garments/Denim – – –

Outerwear – – – – –

Proofing – – – – –

Separate rinse/Starch –/– –/– –/– /– –/–

Recommended Sportswear Fabric Softener

– Not recommended Down items Booster

WoolCare

Detergent

43

The recommendations apply to the temperature ranges given in the Programmechart.

Universal Colour Delicates andwoollens

Special

detergent

Cottons – –

Cottons – –

Minimum iron – – –

Delicates – – –

Woollens – –

Shirts – –

Express 20 – 1) – –

Dark garments/Denim – 1) –

Outerwear – –

Recommended 1) Liquid detergent

– Not recommended 2) Powder detergent

Detergent

44

Dispensing fabric softener andliquid starch at the end of theprogramme

Add the fabric softener or liquidstarch to the compartment orinsert the appropriate capsule. Donot exceed the maximum levelmark.

It will be automatically dispensed in thefinal rinse. At the end of the programmea small amount of water remains in thefabric softener compartment.

Starch can make the siphon tubesticky.If starching frequently, clean thedispenser compartment, especiallythe siphon tube, regularly.

Adding fabric softener or liquidstarch separately

Prepare the starch in accordance withthe manufacturer's instructions on thepackaging.

Useful tip: When adding fabricsoftener, activate the Water plus Extra.

Add fabric softener to the compartment or insert theappropriate capsule.

Add liquid starch to the compartment and powder or viscousstarch to the compartment.

Select the Separate rinse/Starchprogramme.

Change the spin speed if necessary.

Activate the Cap sensor if using acapsule.


Colour run and dye removers/dyes

Damage due to colour run/dyeremovers.Colour run and dye removers cancause corrosion in the washingmachine.Do not use colour run or dyeremovers in this washing machine.

Dyes suitable for use in domesticwashing machines can be used.However, please note that the salt usedin the dyeing process can causecorrosion to stainless steel componentsin the machine if you dye frequently.Always observe the manufacturer'sinstructions carefully.

Cleaning and care

45

External casing and fasciapanel

Risk of electric shock!Mains voltage is present when thewashing machine is switched off.Disconnect the machine from theelectricity supply before cleaning ormaintenance.

Risk of damage due to ingress ofwater.The pressure of a water jet cancause water to get into the washingmachine, resulting in damage tocomponents.Do not spray the washing machinewith a water jet.

Clean the casing and control panelwith a mild cleaning agent or soapand water and dry both with a softcloth.

The drum can be cleaned using asuitable stainless steel cleaning agentfollowing the manufacturer'sinstructions on the packaging.

Damage caused by cleaningagents.Solvent based cleaning agents,abrasive cleaners, glass cleaners ormulti-purpose cleaning agents cancause damage to plastic surfacesand other parts.Do not use any of these cleaningagents.

Cleaning the detergentdispenser drawer

Washing at low temperatures and theuse of liquid detergent can lead to abuild-up of mould and bacteria in thedetergent dispenser drawer.

For hygiene reasons, clean the entiredrawer at regular intervals.

Removing the detergent dispenserdrawer

Pull out the detergent dispenserdrawer until a resistance is felt. Pressdown the release button and at thesame time pull the drawer right out ofthe machine.

Clean the detergent drawer withwarm water.

Cleaning and care

46

Cleaning the siphon and the /compartment channel

Liquid starch results in clogging. Ifclogged, the siphon in the /compartment will not work and thecompartment can overflow.Clean the siphon particularlythoroughly after using liquid starch afew times.

1. Remove the siphon from compartment and clean underwarm running water. Clean thesiphon tube in the same way.

2. Refit the siphon.

Clean the fabric softener channelusing a brush and warm water.

Cleaning the detergent dispenserdrawer housing

Use a bottle brush to removedetergent residues and limescalefrom the jets inside the detergentdispenser drawer compartment.

Replace the detergent dispenserdrawer.

Useful tip: Leave the detergentdispenser drawer slightly open to allowit to dry.

Cleaning and care

47

Cleaning the drum (Hygiene info)Washing at low temperatures and/orusing liquid detergent can causebacteria and unpleasant odours to buildup in the washing machine. Use theCottons 90°C programme to clean themachine. This should be done at thelatest when the indicator light comeson.

Cleaning the water inlet filterThe washing machine has two filters toprotect the water inlet valve. Thesefilters should be checked every sixmonths or so, or more often if there arefrequent interruptions to the watersupply.

Cleaning the filter in the union in theopen end of the inlet hose

First turn off the tap.

Unscrew the inlet hose from the tap.

Remove the rubber seal 1 from therecess.

Using pointed pliers, take hold of theplastic filter bar 2 and remove it.

Clean the filter and the seal.

Put the filter and seal back in thereverse order and reconnect thehose.

Cleaning the filter in the water inletvalve

Using pliers, carefully loosen theribbed plastic nut (seal) on the inletvalve and unscrew.

Use pointed nose pliers to withdrawthe plastic filter by the bar (seeillustration).

Clean the filter and the plastic nut(seal).

Put the filter and plastic nut (seal)back in the reverse order andreconnect the hose.

After cleaning the filters, turn on thetap and check the connections arewatertight. If water drips out, tightenthe connections.

The two filters must be put back inplace after cleaning.

Problem solving guide

48

Problem solving guideWith the help of the following guide, minor faults in the performance of theappliance, some of which may result from incorrect operation, can be put rightwithout contacting Miele. This will save time and money.

Please note that a call-out charge will be applied to unnecessary service visitswhere the problem could have been rectified as described in these operatinginstructions.

Repair work to electrical appliances should only be carried out by anauthorised Miele service technician. Repairs and other work by unqualifiedpersons could be dangerous. Miele cannot be held liable for unauthorised work.

The programme does not start

Problem Possible cause and remedy

The control panelremains dark.

There is no power to the machine. Check whether the mains plug is plugged in and

switched on. Check whether the circuit breaker has tripped.

The washing machine has switched off automaticallyto save energy. Switch the washing machine on again by turning

the programme selector.

and alternatelyappear in the timedisplay.

The door is not closed properly. The door lock couldnot engage. Close the door again. Start the programme again.

If the fault message appears again, contact Miele.


49

The programme is cancelled and a fault indicator light lights upin the control panel.


The fault indicator light lights up, and appear alternately in thetime display and thebuzzer sounds.

The water inlet is blocked or restricted. Check whether the tap is turned on properly. Check whether the inlet hose is kinked. Check whether there is sufficient water pressure.

The filter in the water inlet is blocked. Clean the filter.


The water outlet is blocked or restricted.The drain hose has been fixed too high. Clean the drain filter and the pump. The maximum drain height is 1 m.


The water protection system has reacted. Turn off the tap. Call Miele.

and alternatelyappear in the timedisplay and the buzzersounds.

There is a fault. Disconnect the washing machine from the mains

electricity supply, either by switching it off at thewall socket and withdrawing the plug, or bydisconnecting it at the circuit breaker.

Wait at least 2 minutes before reconnecting thewashing machine to the mains electricity supply.

Then switch the washing machine on again. Restart the programme.

If the fault message appears again, contact Miele.


50

During the programme, a symbol appears in the time display

Message Possible cause and remedy

lights up The programme selector was moved to a differentposition after the programme had started. Turn the programme selector back to the original

position.The programme has been interrupted. Open the door. Close the door.

At the end of the programme, an indicator light lights up in thecontrol panel


The indicator light lights up.

Excessive foam has built up during washing. Use less detergent next time and follow the

manufacturer's instructions on dosage given onthe packaging.

The indicator light lights up.

A programme using a temperature above 60°C hasnot been run for a long period of time. In order to prevent bacteria and unpleasant odours

building up in the machine, run the Cottons 90°Cprogramme using Miele dishwasher and washingmachine cleaner or powder detergent.


51

General problems with the washing machine


The washing machinesmells.

The indicator light was ignored. A programmeusing a temperature above 60°C has not been run fora long period of time. In order to prevent bacteria and unpleasant odours

building up in the machine, run the Cottons 90°Cprogramme using Miele dishwasher and washingmachine cleaner or powder detergent.

The detergent dispenser drawer was left closed afterwashing. Leave the detergent dispenser drawer slightly

open to allow it to dry.

The machine shakesduring the spin cycle.

The machine feet are not level. Level the machine and adjust the feet correctly.

The laundry has notbeen spun properly andthe laundry is still wet.

The machine detected an imbalance during the finalspin and reduced the spin speed automatically. Include both large and small items in the load as

this will give better distribution.

The pump makesstrange noises.

This is not a fault.These slurping noises occur at the end of the pumpsequence as a normal part of operation.

Large amounts ofdetergent residueremain in the detergentdispenser drawer.

The water pressure is too low. Clean the filter in the water inlet. It may be useful to select the Water plus Extra

option.Powder detergent used with water softeners canbecome sticky. Clean the detergent dispenser drawer and in future

add washing powder and then add the watersoftener.


52

General problems with the washing machine


Fabric softener is notcompletely dispensedor too much waterremains in the compartment.

The siphon tube is not correctly positioned, or isclogged up. Clean the siphon (see “Cleaning and care -

Cleaning the detergent dispenser drawer”).

At the end of theprogramme there is stillliquid in the capsule.

The small pipe in the detergent dispenser drawer ontowhich the capsule is placed is blocked. Clean the small pipe.

This is not a fault.For technical reasons, a small amount of water willremain in the capsule.

There is water next tothe capsule in the fabricsoftener compartment.

The Cap sensor was not activated or an emptycapsule was not removed at the end of the lastprogramme. Make sure that you remember to activate the Cap

sensor the next time you insert a capsule. Remove and then dispose of the empty capsule at

the end of each programme.The small pipe in the detergent dispenser drawer ontowhich the capsule is placed is blocked. Clean the small pipe.


53

An unsatisfactory wash result


Liquid detergent doesnot give the requiredresult.

Liquid detergents usually contain no bleachingagents. They do not remove fruit, coffee and teastains. Use a general purpose powder detergent

containing a bleaching agent. Use the appropriate capsule or add stain removers

to the compartment. Never put stain removers and liquid detergent

together in the dispenser drawer.

Grey, greasy particlescling to washed laundry.

Insufficient amounts of detergent were used to breakdown the particles of grease in heavily soiled laundry. Use more detergent or liquid detergent. Before washing the next load, run a Cottons 60°C

programme with powder detergent but without aload.

White residues whichlook like powderdetergent are seen ondark textiles afterwashing.

The detergent contained compounds (zeolites) to aidwater softening which are not soluble in water. Thesehave ended up on the laundry. Try and brush off the residues with a soft brush

once the laundry is dry. Wash dark textiles using a detergent which does

not contain zeolites. Liquid detergents usually donot contain zeolites.

Use the Dark garments/Denim programme.


54

The door will not open


The door cannot bepulled open during aprogramme.

The drum is locked during a programme. Touch the Start/Stop sensor to cancel the

programme.

The programme is cancelled, the door unlocks andyou can pull it open.There is still water in the drum and the machine isunable to drain. Clean the drain filter and the drain pump as

described in “Opening the door in the event of ablocked drain outlet and/or power cut”.

After the programme iscancelled, flashing bars......... appearin the time display.

For safety reasons, the door cannot be opened if thesuds temperature is higher than 55°C. Wait until the temperature in the drum has

decreased and the bars have stopped flashing inthe display.

and alternatelyappear in the timedisplay.

The door lock has jammed. Call Miele.


55

Opening the door in the eventof a blocked drain outlet and/or power cut Switch off the washing machine.

Open the drain pump access panel.

Blocked drain outlet

If the drain outlet is blocked, a largerquantity of water can remain in thewashing machine.

Risk of scalding due to hot suds.Escaping suds will be hot if laundryhas been washed at hightemperatures!Carefully allow all suds to drain off.

Procedure for draining the machine

When removing the drain filter, donot remove it completely.

Place a suitable container under theaccess panel, e.g. a universal oventray.

Slowly and carefully unscrew the filterto let the water out. Be careful not torelease too much water at once. If theflow of water is too strong, somewater can seep into the washingmachine base and activate the waterprotection float switch. This willprevent the washing machine fromfunctioning.

Tighten the drain filter back up againif you need to interrupt the flow ofwater.

Once the flow of water ceases:

Remove the drain filter completely.


56

Clean the drain filter thoroughly.

Remove any foreign objects (e.g.,buttons, coins etc.) and clean theinterior. Turn the impeller by hand tocheck that it rotates freely.

Replace the drain filter correctly andtighten it securely.

Close the drain pump access panel.

Risk of water damage.Make sure the drain filter is securelytightened. Otherwise there is a risk ofwater leakage during use.Replace the drain filter correctly andtighten it securely.

Opening the door

Danger of injury due to rotatingdrum!Reaching into a moving drum isextremely dangerous. Danger ofinjury!Always make sure that the drum isstationary before reaching in toremove laundry.

Use a screwdriver to unlock the doorof the machine as shown.

Pull open the door.

Service

57

Contact in case of faultIn the event of any faults which youcannot remedy yourself, please contactMiele.

Contact information for Miele can befound at the end of this booklet.

Please quote the model and serialnumber of your appliance whencontacting Miele. This information canbe found on the data plate.

The data plate is found above theporthole glass when the door isopened.

Optional accessoriesOptional spare parts and accessoriesfor this washing machine are availablefrom Miele.

WarrantyThe manufacturer's warranty for thisappliance is 2 years.

For further information, please refer toyour warranty booklet.

Installation

*INSTALLATION*

58

Front view

a Inlet hose (tested to withstandpressures up to 7000 kPa)

b Electrical connection cable

c Flexible drain hose (with detachableswivel elbow)

d Control panel

e Detergent dispenser drawer

f Door

g Access to drain filter, drain pump andemergency release

h Four height-adjustable feet

Installation

*INSTALLATION*

59

Rear view

a Drain hose

b Transport clips for electricalconnection cable, inlet and drainhoses

c Electrical connection cable

d Protruding lid for holding whenmoving the machine

e Inlet hose (tested to withstandpressures up to 7000 kPa)

f Safety caps for transit bars

g Transport clips for inlet and drainhoses and for storing transit barswhen not in use

Installation

*INSTALLATION*

60

Installation surfaceA concrete floor is the most suitableinstallation surface. It is far less proneto vibration during the spin cycle thanwooden floorboards or a carpetedsurface.

Please note:

The machine must be level andsecurely positioned.

To avoid vibrations during spinning,the machine should not be installedon soft floor coverings.

If installing on a wooden joist floor:

Install the machine on a plywoodbase (at least 59 x 52 x 3 cm). Thebase should span several joists andbe bolted to the joists and not only tothe floorboards. Check for thepresence of pipes and cables first.

Useful tip: If possible, install themachine in a corner. This is usually themost stable part of the floor.

Transporting the washingmachine to its installation site

Danger of injury due tounsecured lid.Make sure the fixings at the back ofthe lid are secure. They may becomebrittle due to external circumstances.There is a danger of the lid beingpulled off when carrying theappliance.Before carrying the appliance, checkthat the lid is secure where itprotrudes at the back.

Carry the washing machine by thefront feet and by the lid where itprotrudes at the back of theappliance.

Removing the transit bars

Remove the left and right covers.

1. Pull off the transit bar covers and

2. then use a screwdriver to release thecatches at the top and bottom.

Installation

*INSTALLATION*

61

Using the spanner supplied, turn theleft-hand transit bar 90°, then

withdraw the transit bar.

Turn the right-hand transit bar 90°,then

withdraw the transit bar.

Installation

*INSTALLATION*

62

Risk of injury from sharp edges.There is a risk of injury from reachinginto holes that are not covered.To avoid the risk of injury, the holesfor the transit bars must be coveredafter the transit bars have beenremoved!

Fit the stoppers onto the two holes.

Secure the transit bars to the back ofthe washing machine. Make sure thatthe top catch is located above theholder.

Risk of damage from incorrecttransport.The washing machine may becomedamaged if moved without the transitbars in place.Keep the transit bars in a safe place.Fit them again if the machine is to bemoved (e.g. when moving house).

Refitting the transit barsRefitting is carried out by reversing theprocedure.

Installation

*INSTALLATION*

63

Levelling the machineThe washing machine must standperfectly level on all four feet to ensuresafe and proper operation.

Incorrect installation may increaseelectricity and water consumption andmay cause the machine to move about.

Screwing out and adjusting the feet

The four adjustable screw feet are usedfor levelling the washing machine. Allfour feet are screwed in when theappliance is delivered.

Using the spanner supplied, turncounter nut 2 in a clockwise direction.Then turn counter nut 2 together withfoot 1 to unscrew.

Use a spirit level to check that thewashing machine is standing level.

Hold foot 1 securely with a pipewrench. Turn counter nut 2 againusing the spanner supplied until it sitsfirmly up against the housing.

Risk of damage due toincorrectly aligned washing machine.There is a danger of the washingmachine moving about if the feet arenot secured.Turn all four counter nuts for the feetuntil they sit firmly up against thehousing. Please also check this forthe feet which did not needadjustment.

Installation

*INSTALLATION*

64

Installing under a continuousworktop

Risk of electric shock due toexposed cables.There is a risk of coming into contactwith live parts while the lid isremoved.Do not remove the washing machinelid.

This washing machine (with lid intact)can be pushed under a worktop if thereis space to do so.

Washer and dryer stack

A Miele tumble dryer can be stackedwith the washing machine. Theappropriate “WTV” stacking kit* tomatch your tumble dryer is required.

All parts marked * are available fromMiele.

Please note the following:

a = at least 2 cm

b = WTV without drawer: 172 cmWTV with drawer: 181 cm

c = 68 cm

Installation

*INSTALLATION*

65

The Miele water protectionsystemThe Miele water protection systemprotects all parts of the washingmachine and surrounds from waterdamage.

The system consists of three maincomponents:

– the inlet hose

– the electronic unit and drainage andoverflow protection

– the drain hose

Inlet hose

– Protection against burstingThe inlet hose is tested to withstandpressures up to 7000 kPa.

Electronic unit and washing machinehousing

– Sump: Any leaking water is collectedin a sump in the base of the machine.A float switches off the water inletvalves, preventing any more waterfrom flowing into the machine andwater in the suds container ispumped away.

– Overflow protection: This preventsthe washing machine taking in toomuch water. If the water levelexceeds a certain level, the drainpump switches on and pumps theexcess water away in a controlledway.

Drain hose

The drain hose is protected by aventilation system which prevents thewashing machine from being emptiedcompletely.

Installation

*INSTALLATION*

66

Connection to the water supplyThe washing machine should beconnected to a mains water supply inaccordance with current local andnational safety regulations.

IMPORTANT Australia and NewZealand

This appliance must be installedaccording to AS/NZS 3500.1. Backflowprevention is already integrated in theappliance.

The machine is designed to operatewith a flow pressure of between 100and 1000 kPa. If it is higher than1000 kPa, it is essential to fit a reducervalve.

Connection to the mains water supplyshould incorporate a mains tap with ¾"threaded union. The tap should be fittedby a qualified plumber.

The connection point is subjectto mains water pressure. Turn on thetap slowly and check for leaks.Correct the position of the washerand union if appropriate.

The washing machine is not suitablefor connection to a hot water supply.

Maintenance

Only use a genuine Miele hose shouldyou ever need a replacement. These aretested to withstand pressures up to7000 kPa.

A filter is located in the open endof the inlet hose and another in theintake point to protect the inlet valve.Neither filter may be removed.

Hose extension

Longer hoses 2.5 m or 4.0 m in lengthare available from Miele as optionalaccessories.

Installation

*INSTALLATION*

67

DrainageThe suds are drained through a drainpump with a 1 m delivery head. For thewater to drain freely, the hose must beinstalled free of kinks.If required, the hose can be extended toa length of up to 5 m. The necessaryparts can be purchased from Miele.

For a delivery head of more than 1 m(up to a max. of 1.8 m) a replacementdrain pump will need to be fitted.Please contact Miele for advice.For a delivery head of 1.8 m the hosecan be extended to a length of up to 2.5m. The necessary parts can bepurchased from Miele.

Drain hose connection options

1. Directed into a sink or basin.

Please note:

– Hook the hose over the edge andsecure it.

– Make sure that the water can drainaway freely without hindrance.Otherwise there is a risk of wateroverflowing or of some of thedrained water being sucked backinto the machine.

2. Connected securely to a plastic drainpipe with a rubber nipple (there is noneed to use a siphon).

3. Connected securely to a floor drain(gully).

4. Connected securely to a standpipe.

Please note:

a Adapter

b Nut

c Hose clip

d End of the hose

Fit the adapter to the sink drainoutlet using the nut .

Attach the end of the hose to theadapter .

Use a screwdriver to tighten the hoseclip up close to the nut.

Installation

*INSTALLATION*

68

Electrical connectionThe washing machine is supplied with amains cable with moulded plug readyfor connection to a switched socket.

The socket must be easily accessibleafter the machine has been installed. Ifthe switch is not accessible afterinstallation an additional means ofdisconnection must be provided for allpoles.

Risk of fire from overheating!Connecting the washing machine toa multi-socket plug adapter or to anextension lead can overload thecable.Do not use an extension lead ormulti-socket plug adapter.

All electrical work must be carried outby a suitably qualified and competentperson, in strict accordance withnational and local safety regulations.For extra safety, it is advisable to installa residual current device (RCD) with atrip current of 30 mA. Ensure power isnot supplied to the appliance until afterthe installation has been completed.Connection should be made via asuitable switched socket.

If the connection cable is damaged, itmust only be replaced with a specificconnection cable of the same type(available from Miele) in order to avoid ahazard. For safety reasons, suchreplacement may only be carried out bya suitably qualified and competenttechnician or Miele.

The data plate indicates the nominalpower consumption and theappropriate fuse rating. Compare thespecifications on the data plate withthose of the mains electricity supply.

If in any doubt, consult a qualifiedelectrician.

Do not connect the washing machine toa stand-alone inverter such as thoseused with an autonomous energysource, e.g. solar power. When thewashing machine is switched on, powersurges could result in a safety switch-off. This could damage the electronics.

Technical data

69

Height 850 mm

Width 596 mm

Depth 636 mm

Depth with door open 1.054 mm

Height for building under 850 mm

Width for building under 600 mm

Weight Approx. 100 kg

Capacity 7 kg dry laundry

Voltage See data plate

Rated load See data plate

Fuse rating See data plate

Consumption data See “Consumption data”

Water flow pressure minimum 100 kPa

Water flow pressure maximum 1000 kPa

Inlet hose length 1.60 m

Drain hose length 1.50 m

Connection cable length 2.00 m

Drain pump head max. 1.00 m

Drain pump length max. 5.00 m

LEDs Class 1

Test certificates awarded See data plate

Power consumption when switched off 0.3 W

Power consumption when not switchedoff

2.5 W

Consumption data

70

Consumption data according to AS/NZS 2040.1 & AS/NZS 2040.2

Load Consumption data

Energyin kWh

Waterin litres

DurationCold water

Cottons 40°C 7.0 kg 0.63 63 3 h 59 min

Note for test institutes:

The detergent must be added via the detergent dispenser drawer.

Consumption data can vary from the nominal values listed depending on waterpressure, water hardness, water inlet temperature, room temperature, type andvolume of load, fluctuations in the electricity supply and any Extras select

Consumption data

71

Load Energy Water Duration Residualmoisture

kg kWh Litres h:min %

Cottons 60°C 7,0 0,90 50 2:59 53

60°C 3,5 0,88 48 2:59 53

40°C 3,5 0,50 40 2:59 53

Cottons 90°C 7,0 2,00 50 2:29 53

60°C 7,0 1,20 50 2:29 53

60°C 3,5 1,00 48 2:19 53

40°C 7,0 0,84 69 2:39 53

40°C 3,5 0,60 48 2:29 53

20°C 7,0 0,35 69 2:39 53

Minimum iron 30°C 3,5 0,35 47 1:59 30

Delicates 30°C 2,0 0,25 30 1:09 –

Woollens 30°C 2,0 0,23 35 0:38 –

Express 201) 40°C 3,5 0,34 30 0:20 –

Shirts 60°C 2,0 0,77 40 1:31 –

1) Short Extra activated

Consumption data can vary from the nominal values given depending on waterpressure, water hardness, water inlet temperature, room temperature, type andvolume of load, fluctuations in the electricity supply and any Extras selected.

Programmable functions

72

The programmable functions are usedto alter the machine's electronics tosuit changing requirements.Programmable functions can bealtered at any time.

Programming is carried out in 8 steps(, , ... ) using buttons andsensors.

Accessing the programming level

Before you begin, ensure the following:

– The washing machine is switched on(the programme selector is pointingto a wash programme).

– The washing machine door is open.

Touch the Start/Stop sensor andhold it down during step .

Close the washing machine door.

Wait until the Start/Stop sensor lightsup constantly ...

... and then release the Start/Stopsensor.

After approx. four seconds, will lightup in the time display.

Choosing and selectingprogrammable functions

The number of the programmablefunction will appear in the display as and a number: e.g. .

Touch the or sensor to scroll tothe next or previous programmablefunction:


Keypad tone

PIN Code

Control panel standby status

Memory

Longer pre-wash Cottons

Soak duration

Gentle action

Reduce temperature

Water plus

Water plus level

Maximum rinse level

Suds cooling

Anti-crease

Backlight brightness dimmed

Confirm the selected programmablefunction by touching the Start/Stopsensor.


73

Editing and saving theprogrammable functionYou can either switch a programmablefunction on or off or select differentoptions.

Touch the or sensor to switchthe programmable function on/off orto select an option:

Programmable function

Available options

–

X O

O X

X O

O X

O X X X

O X X X

O X

O X

O X X

O X X X

O X

O X

O X

X X O X X

X = can be selected

O = factory setting

Confirm the chosen selection withthe Start/Stop sensor.

The number of the programmablefunction, e.g. will light up again.

Exiting the programming level Turn the programme selector to .

The settings have been changed. Youcan alter the settings again at any time.

Keypad tone

Each touch of a sensor is confirmedwith an audible tone.

Options

= Keypad tone is switched off

= Keypad tone is switched on(factory default setting)


74

PIN Code

The PIN code prevents the washingmachine being used without yourknowledge.

When the code has been activated, youhave to enter a code after switching thewashing machine on. Otherwise thewashing machine cannot be operated.

Options

= PIN code is switched off(factory default setting)

= PIN code is switched on

Using the washing machine with aPIN code

The code is 125 and cannot be altered.

Switch on the washing machine.

appears in the time display andthe and sensors light up.

Touch the sensor.

appears in the time display.

Confirm the number with the Start/Stop sensor.

The first number was saved and youcan now enter the second numberusing the and sensors.

Enter the second and third numbersand confirm the numbers with theStart/Stop sensor.

The lock is released and a washprogramme can now be selected andstarted.

Control panel standbystatus

To save energy the time display andsensors will go out after 10 minutes,and only the Start/Stop sensor willflash slowly.

Options

= OffThe time display and sensorswill remain lit up while thewashing machine is switchedon

= On (factory default setting)The time display and sensorswill switch off after 10 minutesif the programme is started.

However; the time display andsensors will remain lit up for10 minutes after a Delay starttime has elapsed, after the endof a programme, or at the endof the anti-crease phase.


75

Memory

The washing machine will save thelast settings (temperature, spin speedand some of the Extras) selected for aprogramme after the programme hasstarted.

When the programme is chosen again,the saved settings will appear in thedisplay.

Options

= Memory is switched off(factory default setting)

= Memory is switched on

Longer pre-wash Cottons

If you require a longer pre-wash youcan extend the pre-wash time.

Options

= No increase in the pre-washtime (factory default setting)

= + 6 minutes increase in thepre-wash time



Soak duration

You can set a duration for the soakprocess of between 30 minutes and2 hours.

A duration can be selected in 30-minuteincrements. When the Soak Extra isselected, the laundry will be soaked forthe duration selected.

Options

= 30 minutes soak duration(factory default setting)

= 1 hour soak duration

= 1 hour 30 minutes soakduration

= 2 hours soak duration

Gentle action

With gentle action activated, drumagitation is reduced. In this way, lightlysoiled items can be washed moregently.

Gentle action can be activated for theCottons and the Minimum ironprogrammes.

Options

= Gentle action is switched off(factory default setting)

= Gentle action is switched on


76

Reduce temperature

At high altitudes water has a lowerboiling point. Miele recommendsactivating the Reduce temperaturesetting at altitudes of or above 2000 mto prevent water from boiling. Themax. temperature is reduced to 80°C,even if a higher temperature isselected.

Options

= The Reduce temperaturesetting is switched off (factorydefault setting)

= The Reduce temperaturesetting is switched on

Water plus

You can determine the amount ofwater used if the Water plus Extra isselected.

Options

= More water is used in the washand rinse stages (factorydefault setting)

= An extra rinse is carried out

= The water level is increased inthe wash and rinse stages andan additional rinse is carriedout

Water plus level

There are three different water levelswhich can be selected by activatingthe Water plus Extra.

Options

= No higher water level (factorydefault setting)

= Water level increased by 1 levelwhen washing and rinsing

= Water level increased by2 levels when washing andrinsing

= Water level increased by3 levels when washing andrinsing

Maximum rinse level

The water level in the rinse can bepermanently set to the highest value.

This function is important for allergysufferers as it achieves excellent rinseresults. The water consumption will beincreased.

Options

= Maximum rinse level isswitched off (factory defaultsetting)

= Maximum rinse level isswitched on


77

Suds cooling

When this is activated, additionalwater flows into the drum at the end ofthe main wash to cool the suds down.Hot suds can damage plastic drainagepipes.

Suds cooling takes place when aCottons programme with a temperatureof 70°C or higher is selected.

Suds cooling should be activated:

– to prevent the danger of scalding ifthe drain hose is hooked over theedge of a sink or basin.

– where the drainage pipes do notcomply with DIN 1986.

Options

= Suds cooling is switched off(factory default setting)

= Suds cooling is switched on

Anti-crease

The Anti-crease function helps preventcreasing if laundry is not going to beremoved immediately after the end ofthe programme.

At the end of the programme, the drumcontinues to turn at intervals for up to30 min. The door can be opened at anytime during the anti-crease phase.

Options

= The Anti-crease function isswitched off (factory defaultsetting)

= The Anti-crease function isswitched on

Backlight brightnessdimmed

The brightness of the dimmed sensorsin the control panel can be selected atseven different levels.

It will change as soon as a differentsetting is chosen.

Options

= darkest level

= brightest level

= factory default setting

Optional accessories

78

Detergent, fabric care, additives andmachine care products are available forthis machine. All the products havebeen designed for Miele appliances.

These and many other useful productscan be ordered via the internet atshop.miele.com (depending on country)or from Miele (see end of this bookletfor contact details).

Detergent

UltraWhite

– Powder detergent

– Suitable for white and light colouredlaundry as well as heavily soiledcotton items

– Effective stain removal even at lowtemperatures

UltraColor

– Liquid detergent for coloured items

– Suitable for coloured and dark/blackitems

– Protects bright colours from fading

– Effective stain removal even at lowtemperatures

– Also available as a powder detergent.

Sensitive Skin Powder

– Powder detergent with a mildfragrance for use with white or lightcoloured garments

– Specially formulated for people withsensitive skin

– Excellent stain removal even at lowtemperatures

– Environmentally friendly (nophosphates) and no dyes orpreservatives

– Not suitable for silks or woollens


79

Specialist detergentsSpecialist detergents are available ascapsules in convenient single doseamounts or in a handy bottle.

Outerwear

– Liquid detergent for outerwear andperformance clothing

– Cleans with care and is gentle oncolours

– With lanolin to care for and conditionmembrane fabric

Sportswear

– Liquid detergent for sportswear andfleece garments

– Neutralises unpleasant odours

– Retains the shape of the textiles

Down Items

– Liquid detergent suitable for pillows,sleeping bags and down filled items

– Retains the elasticity of down andfeather filled items

– Retains the breathability of downfilled items

– Prevents down filling clumpingtogether


80

WoolCare

– Liquid detergent for woollens anddelicates

– Includes a special wheat proteinconditioning formula

– Helps prevent pilling and felting

– Gentle on colours

SilkCare

– Liquid detergent for silks

– Contains a special silk proteinconditioning formula

– Gentle on colours

– Only available as capsules

Fabric careFabric care is available as capsules in convenient single dose amounts or ina handy bottle.

Proofing agent

– For proofing microfibre fabrics, e.g.rain coats

– Retains the breathability of garments

Fabric softener

– Fresh, natural fragrance

– Makes laundry soft to handle

– Available as capsules in convenientsingle dose amounts and as liquiddetergent.

Additives

Booster

– For removing stains

– Suitable for white and colouredlaundry

– Available as capsules inconvenient single dose amounts

Machine care products

IntenseClean

– For cleaning the washing machinethoroughly and effectively

– Removes grease, bacteria andunpleasant odours

– Use 1–3 times per year

Descaler

– Removes heavy limescale deposits

– Mild and gentle with natural citricacid

Water softener tablets

– Reduces quantities of detergent forhard water

– Less detergent residue in textiles

– Less chemicals in waste water due toreduced amount of detergent

www.miele.com.au

Miele Experience Centre and Head Office Melbourne:1 Gilbert Park DriveKnoxfield, VIC 3180

Miele Experience Centre South Melbourne:206-210 Coventry StreetSouth Melbourne, VIC 3205

Miele Experience Centre and Office Sydney:3 Skyline PlaceFrenchs Forest, NSW 2086

Miele Experience Centre and Office Brisbane:Tenancy 4C, 63 Skyring TerraceNewstead, QLD 4006

Miele Experience Centre and Office Perth:

83-85 Sir Donald Bradman DriveHilton, SA 5033

205-207 Stirling HighwayClaremont, WA 6010

Miele Experience Centre and Office Adelaide:

Miele Australia Pty. Ltd.

Miele New Zealand Limited

Level 2, 10 College HillFreemans Bay, Auckland 1011

Miele Experience CentreAuckland:8 College HillFreemans Bay, Auckland 1011Telephone:0800 464 353 (0800 4 MIELE)www.miele.co.nz

Miele Global HeadquartersGermanyMiele & Cie. KGCarl-Miele-Straße 2933332 GüterslohFederal Republic of Germany

Head Office:

IRD 98 463 631

ACN 005 635 398ABN 96 005 635 398

Miele Experience Centre Gold Coast:131 Ferry RoadSouthport, QLD 4215

M.-Nr. 10 832 530 / 02en-AU, NZ

WDB 030

Documents

Operating instructions Washing machine€¦ · The washing machine is not suitable for outdoor use. It must only be used to wash garments which have been declared suitable for washing