Operating Instructions Dishwasher - Miele · 2017-02-21 · IMPORTANT SAFETY INSTRUCTIONS 7 Correct use This dishwasher is intended for use in domestic households and similar residential

Operating InstructionsDishwasher

To prevent accidents and machine damage, read these instructions be-fore installation or use.

en-US M.-Nr. 10 546 840HG05

2

Contents

3

IMPORTANT SAFETY INSTRUCTIONS ................................................................ 6

Guide to the dishwasher ..................................................................................... 15Appliance overview ............................................................................................... 15Control panel ......................................................................................................... 16Display functions................................................................................................... 17

Caring for the environment ................................................................................ 18Energy-saving dishwashing................................................................................... 19

Before using for the first time ............................................................................ 20Opening the door .................................................................................................. 20Closing the door.................................................................................................... 20Basic settings........................................................................................................ 21Before using the appliance for the first time, you require: .................................... 23Dishwasher salt ..................................................................................................... 23

Filling the salt reservoir..................................................................................... 24Salt refill indicator............................................................................................. 25

Rinse aid................................................................................................................ 26Adding rinse aid ............................................................................................... 26Rinse aid indicator............................................................................................ 27

Loading the dishwasher...................................................................................... 28Tips........................................................................................................................ 28Loading examples ................................................................................................. 30FlexAssist .............................................................................................................. 34Upper basket......................................................................................................... 34

Adjusting the upper basket .............................................................................. 37Lower basket......................................................................................................... 38Pot rests and filters................................................................................................ 41Cutlery ................................................................................................................... 43

3D cutlery tray+ (depending on model) ............................................................ 43Cutlery basket (depending on model) .............................................................. 45

Operation.............................................................................................................. 46Detergent............................................................................................................... 46Turning on.............................................................................................................. 49Selecting a program .............................................................................................. 49Starting a program ................................................................................................ 50Time display .......................................................................................................... 50Energy management ............................................................................................. 51At the end of the program ..................................................................................... 51Turning off the dishwasher .................................................................................... 52Unloading the dishwasher..................................................................................... 52

Contents

4

Interrupting a program........................................................................................... 53Changing a program.............................................................................................. 53

Options ................................................................................................................. 54Options.................................................................................................................. 54FlexiTimer with EcoStart ....................................................................................... 55

Program overview ............................................................................................... 58

Settings menu...................................................................................................... 62Opening the Settings menu................................................................................... 62Language ........................................................................................................... 62Time of day............................................................................................................ 62Water hardness ..................................................................................................... 63Rinse aid................................................................................................................ 64EcoStart................................................................................................................. 64Soak ...................................................................................................................... 66Pre-Rinse............................................................................................................... 67Brightness ............................................................................................................. 67Volume................................................................................................................... 67Refill indicators ...................................................................................................... 68Check filters .......................................................................................................... 68AutoOpen .............................................................................................................. 69Optimize Standby.................................................................................................. 69Software version.................................................................................................... 70Showroom program............................................................................................... 70Factory default settings......................................................................................... 70Closing the Settings menu .................................................................................... 70

Cleaning and care ............................................................................................... 71Cleaning the wash cabinet .................................................................................... 71Cleaning the door and the door seal..................................................................... 71Cleaning the control panel .................................................................................... 71Cleaning the indicator reflector panel ................................................................... 71Cleaning the door front ......................................................................................... 72Filter system .......................................................................................................... 73Cleaning the spray arms........................................................................................ 75

Frequently Asked Questions .............................................................................. 76Technical problems ............................................................................................... 76Water intake fault................................................................................................... 78Water drainage fault .............................................................................................. 79General problems .................................................................................................. 80Noises.................................................................................................................... 81

Contents

5

Poor cleaning results ............................................................................................. 82

Frequently asked questions ............................................................................... 85Cleaning the drain pump and non-return valve..................................................... 85

Customer service ................................................................................................ 86Repairs .................................................................................................................. 86Warranty ................................................................................................................ 86

Optional accessories .......................................................................................... 87

Installation Instructions ......................................................................................... 89Electrical connection .......................................................................................... 90

Water connection ................................................................................................ 92Water intake .......................................................................................................... 92Drainage ................................................................................................................ 93

Sound emission testing ...................................................................................... 94

IMPORTANT SAFETY INSTRUCTIONS

6

This dishwasher complies with current safety requirements. Inap-propriate use can, however, lead to personal injury and damage toproperty.

To avoid the risk of accidents and damage to the dishwasher,please read the installation plan and the operating instructionscarefully before it is installed and used for the first time. Both con-tain important information on its installation, safety, use and main-tenance.

Keep the installation plan and the operating instructions in a safeplace and pass them on to any future owner.

Miele cannot be held liable for damage caused by non-compliancewith this information.


7

Correct use

This dishwasher is intended for use in domestic households andsimilar residential environments.

This dishwasher is not suitable for outdoor use.

It must only be used as specified in these operating instructionsfor cleaning domestic dishes and cutlery. Any other usage is notsupported by the manufacturer and could be dangerous.

This appliance is not intended for use by persons (including chil-dren) with reduced physical, sensory or mental capabilities, or lackof experience and knowledge.


8

Safety with children

Children must be kept away from the appliance unless they areconstantly supervised.

Children should be supervised to ensure that they do not play withthe appliance. Keep small children away from the appliance at alltimes to avoid the risk of injury. There is the risk that children maylock themselves in the dishwasher.

If the automatic door opening mechanism (depending on model) isactive keep young children away from the area in which the dooropens. Danger of injury in the unlikely event of a fault with the open-ing mechanism.

Danger of suffocation! Ensure that any plastic wrappings, bags,etc. are disposed of safely and kept out of the reach of children.

Keep children away from detergents. Dishwasher detergents cancause burning in the mouth, nose and throat if swallowed, or inhibitbreathing. Keep children away from the dishwasher when the door isopen. There could still be detergent residues in the cabinet. Seekmedical attention immediately if your child has swallowed or inhaleddetergent.


9

Technical safety

Installation, repair, and maintenance work should only be per-formed by a Miele-authorized service technician. Work by unquali-fied persons could be dangerous and may void the warranty.

Before installation, check the dishwasher for visible signs of dam-age. Under no circumstances should you use a damaged dish-washer. A damaged dishwasher could be dangerous.

The electrical safety of this appliance can only be guaranteedwhen continuity is complete between it and an effective groundingsystem. It is most important that this basic safety requirement ispresent and regularly tested and, where there is any doubt, the elec-trical system in the house should be checked by a qualified electri-cian.Miele cannot be held liable for the consequences of an inadequategrounding system (e.g. electric shock).

Reliable and safe operation of this dishwasher can only be as-sured if it has been connected to the electrical supply.

If the dishwasher is plugged into the electricity supply using a 3-pin plug with a grounding contact (it must not be hard-wired), theelectrical socket must be easily accessible after the dishwasher is in-stalled so that it can be disconnected from the electrical supply atany time.

There must be no electrical sockets behind the dishwasher. Thereis a danger of overheating and fire risk if the dishwasher is pushedup against a plug.

The dishwasher must not be installed under a cooktop. The highradiant temperatures which are sometimes generated by a cooktopcould damage the dishwasher. For the same reason, it should not beinstalled next to open fires or other appliances which give off heat,such as heaters, etc.


10

To avoid the risk of damage to the dishwasher, make sure that theconnection data on the data plate (fuse rating, voltage, and fre-quency) matches the electrical supply before connecting the dish-washer to the mains. Consult a qualified electrician if in any doubt.

Do not connect the dishwasher to the electrical supply until it hasbeen fully installed and any adjustment has been made to the doorsprings.

The dishwasher may only be operated if the door opening mecha-nism is working correctly. Otherwise there could be a risk of dangerwhile the automatic door opening mechanism (depending on model)is active.To check that the door opening mechanism is working correctly:

– The door springs must be adjusted equally on both sides. Theyare correctly adjusted when the door remains stationary when lefthalf open (approx. 45° opening angle). It is also important that thedoor cannot fall open.

– The door locking pins automatically retract when the door opensat the end of the drying phase.

Do not connect the appliance to the electrical supply by a multi-socket adapter or an extension lead. These do not guarantee the re-quired safety of the appliance (e.g. danger of overheating).

This appliance must not be installed and operated in a non-sta-tionary location (e.g., on a ship).

Do not install the dishwasher in a room where there is a risk offrost. Frozen hoses may burst or split. The reliability of the electronicmodule may be impaired at temperatures below freezing point.

To avoid any damage to the appliance, the dishwasher must onlybe operated when it is connected to a fully vented plumbing system.

The water pressure (flow pressure at the connection point) mustbe between 7.25 - 145 psi.


11

A damaged appliance could be dangerous. If the dishwasher getsdamaged, turn off the electrical supply and contact Miele.

The manufacturer's warranty will be invalidated if the appliance isnot repaired by a Miele-authorized service technician.

Defective components should be replaced by Miele original partsonly. Only with these parts can the manufacturer guarantee thesafety of the appliance.

During installation, maintenance and repair work, the appliancemust be disconnected from the electrical supply (turn it off and with-draw the plug from the socket).

If the connection cable is damaged, it must be replaced with aspecial cable of the same type (available from Miele) by a Miele-au-thorized service technician only.

This dishwasher is supplied with a special bulb to cope with par-ticular conditions (e. g. temperature, moisture, chemical resistance,abrasion resistance and vibration). This special bulb must only beused for the intended purpose. It is not suitable for room lighting.Replacement bulbs may only be fitted by a Miele-authorized techni-cian or the Miele Technical Service.


12

Proper installation

The dishwasher must be installed and connected in compliancewith the installation plan.

Be careful when installing the dishwasher. Wear protec-tive gloves to avoid injury on any sharp metal components.

The dishwasher must be correctly aligned horizontally to ensureproblem-free operation.

In order to ensure stability, built-under and integrated dishwashersmust only be installed under a continuous counter which is securedto adjacent cabinetry.

The door springs must be adjusted equally on both sides. Theyare correctly adjusted when the door remains stationary when lefthalf open (approx. 45° opening angle). It is also important that thedoor cannot fall open. The appliance may only be used with correctly adjusted doorsprings.


13

Proper use

Do not use solvents in the dishwasher. Danger of explosion!

Do not inhale or ingest powder detergent. Dishwasher detergentscontain irritant or corrosive ingredients which can cause burning inthe nose, mouth, and throat if swallowed, or inhibit breathing. Seekmedical attention immediately if detergent has been swallowed or in-haled.

Avoid leaving the door open unnecessarily as someone could tripover it and be injured by it.

Do not sit or lean on the opened door. This could cause the dish-washer to tip and be damaged, and you could get injured.

Dishes can be very hot at the end of a program. Allow them tocool until they are comfortable enough to handle before unloading.

Only use detergent and rinse aid formulated for domestic dish-washers. Do not use dishwashing liquid.

Do not use commercial or industrial detergents as these maycause damage, and there is a risk of a severe explosive chemical re-action (such as an explosive oxyhydrogen gas reaction).

Do not fill the rinse aid reservoir with powder or liquid detergent.This will cause serious damage to the reservoir.

Inadvertently filling the salt reservoir with powder or liquid dish-washer detergent will damage the water softener. Make sure youhave picked up the correct packet of dishwasher salt before fillingthe salt reservoir!

Only use special coarse grained dishwasher salt for reactivation.Do not use other salts such as cooking salt, agricultural grade orgritting salt. These may contain insoluble additives which can impairthe functioning of the water softener.


14

In an appliance with a cutlery basket (depending on model), cut-lery is cleaned and dried more efficiently if placed in the basket withthe handles downwards. However, to avoid the risk of injury, placeknives and forks with the handles upwards.

Plastic items which cannot withstand being washed in hot water,such as disposable plastic containers or plastic cutlery should notbe cleaned in the dishwasher. The high temperatures in the dish-washer may cause them to melt or lose shape.

If you use the "FlexiTimer/Delay Start" option (depending onmodel), make sure that the dispenser is dry before adding detergent.Wipe dry if necessary. Detergent will clog if poured into a damp dis-penser and may not be thoroughly dispersed.

Please observe the information given in "Technical data" regardingthe capacity of the dishwasher.

Accessories

Use only genuine original Miele parts. If spare parts or acces-sories from other manufacturers are used, the warranty may becomeinvalid.

Disposal of your old dishwasher

Make the door lock inoperative so that children cannot acciden-tally shut themselves in. Remove or destroy the locking bracket ofthe door lock, and make appropriate arrangements for the disposalof the appliance.

SAVE THESE INSTRUCTIONS AND PASS THEM ON TO ANY FUTURE USER

Guide to the dishwasher

15

Appliance overview

a Upper spray arm (not visible)

b Cutlery tray (depending on model)

c Upper basket

d Middle spray arm

e Heat exchanger return (depending onmodel)

f Lower spray arm

g Filter combination

h Data plate

i Rinse aid reservoir

j Double-chamber detergent dispenser

k In-operation indicator light

l Reservoir for reactivation salt


16

Control panel

a In-operation indicator light

b Program selection

c Short and Extra Economical optionbuttons with indicator lights

d Arrow buttons

e button (FlexiTimer) with indicatorlight

f OK button

g Display

h Program selection button

i (On/Off) button

These operating instructions apply to several different dishwasher models withdifferent heights. The specific dishwasher models are referred to as follows: Standard = 31 11/16" (80.5 cm) high dishwashers (integrated) and 33 1/4" (84.5 cm) high dishwashers (freestanding) XXL = 33 1/4" (84.5 cm) high dishwashers (integrated)


17

Display functions

General information

The display is used to select or set thefollowing:

– The program

– The FlexiTimer (Delay Start)

– The Settings menu

The display can show the following:

– The program stage

– The estimated time left for the pro-gram to run

– Any relevant fault messages and in-formation

To save energy, the dishwasherswitches off after a few minutes if youdo not press any buttons during thistime. To switch the dishwasher back onagain, press the button.

Settings menu

The Settings menu is used to adapt theelectronic module of the dishwasher tochanging requirements. See the "Set-tings menu" chapter for more informa-tion on accessing the settings menu.

The arrows in the display indicate addi-tional options. You can use the ar-row buttons next to the display, as ap-propriate, to select these additional op-tions.

The OK button is used to confirm amessage or setting and also to move tothe next menu or another level.

The option which is selected will have acheck next to it.

To exit a sub-menu, use the arrowbuttons to select the Back option inthe display and confirm your choicewith OK.If you do not press any of the buttonsfor several seconds, the display with re-turn to the previous level. You may needto enter your settings again.

Caring for the environment

18

Disposal of the packing mate-rialThe cardboard box and packing materi-als protect the appliance during ship-ping. They have been designed to bebiodegradable and recyclable.

Ensure that any plastic wrappings,bags, etc. are disposed of safely andkept out of the reach of children. Dan-ger of suffocation!

Disposal of your old applianceElectrical and electronic appliancescontain valuable materials. They alsocontain certain substances, compoundsand components which were essentialfor the proper functioning and safe useof the equipment. Handling these mate-rials improperly by disposing of them inyour household waste can be harmful toyour health and the environment. There-fore, please do not dispose of your oldappliance with regular household wasteand follow local regulations on properdisposal.

Consult with local authorities, dealers orMiele in order to dispose of and recycleelectrical and electronic appliances.Miele assumes no responsibility fordeleting any personal data left on theappliance being disposed. Please en-sure that your old appliance is keptaway from children until removal. Ob-serve safety requirements for appli-ances that may tip over or pose an en-trapment hazard.

Caring for the environment

19

Energy-saving dishwashingThis dishwasher is economical in theconsumption of water and energy. For best results follow these tips:

– For most economical dishwashing,make full use of the baskets withoutoverloading the dishwasher.

– Choose a program that best suits thedegree of soiling and the type ofdishes being washed.

– Select the Normal program (depend-ing on model) for energy-saving dish-washing. This program is the most ef-ficient in terms of its combined en-ergy and water consumption at clean-ing normally soiled dishes.

– Follow the detergent manufacturer'srecommendations on detergentdosage.

– When using powder or liquid deter-gent, you can use 1/3 less detergent ifbaskets are only half full.

– The dishwasher can be connected toa hot water supply for furthereconomies. If the water is heated byfor example, solar panels, this wouldbe energy efficient. However, if your water is heated byelectricity we recommend cold waterconnection.

Before using for the first time

20

Opening the doorAt the end of programs with a dryingphase (see "Program overview"), thedoor will open automatically a little inorder to help the drying process. This function can be deactivated if pre-ferred (see "Settings menu - Au-toOpen").

Pull the handle to open the door.

Open the door fully so that the doorcatch rail retracts again.

If the door is opened during operation,all functions are automatically inter-rupted.

Water in the dishwasher may behot. Danger of scalding!Only open the door during operationif absolutely necessary and exerciseextreme caution when doing so.

Keep the area around the doorfree of obstructions.

Closing the door Push the baskets in.

Then lift the door upwards and pushuntil it clicks into position.

Danger of crushing injuries!Do not put your hand inside the dooras it is closing.


21

Basic settings Open the door.

Turn the dishwasher on with the button.

The welcome screen will appear whenthe dishwasher is turned on for the firsttime.

Language

The display will change automatically tothe screen for setting the language.

Use the arrow buttons to selectthe language you want and also thecountry, if appropriate, and confirmyour selection with OK.

For more information about the func-tion of the display, see "Display".

A check will appear next to the lan-guage that has been set.

Time of day

The display will then change to thescreen for setting the time.

The current time of day must be set be-fore you can use the "FlexiTimer" pro-gramming option.

Use the arrow buttons to set thehour and confirm with OK.

Then set the minutes and confirmwith OK.

Keeping the arrow buttonspressed will increase or decrease thetime automatically.


22

Water hardness

The display changes to the screen forsetting the water hardness.

– The dishwasher must be pro-grammed to the correct water hard-ness for your area.

– Your local water authority will be ableto advise you of the water hardnesslevel in your area.

– Where the water hardness fluctuatese.g. between 10 - 16 gr/gal (10 - 15°d), always program the dishwasherto the higher value (16 gr/gal or 15 °din this example).

It is useful to know your water hardnessso that you can provide the servicetechnician with this information in theevent of any service calls.

Enter the water hardness below:

____________ gr/gal (°d)

The dishwasher is programmed at thefactory for a water hardness level of 1gr/gal (1 °d).

Use the arrow buttons to selectthe hardness of your water supplyand confirm with OK.

See "Settings menu, Water hardness"for more information.

The message Set-up successfully com-pleted will then appear in the display.

After confirming this with OK, theprompts Refill salt and Refill rinse aidmay appear.

Add salt and rinse aid if necessary(see "Before using for the first time,Dishwasher salt" and "Rinse aid").

Confirm the messages with OK.

The program selected will appear brieflyin the display and the appropriate indi-cator light will come on.Then, the display will show the esti-mated program duration for the pro-gram selected.

These basic settings will be saved afterthe dishwasher has been through onecomplete program.


23

Before using the appliance forthe first time, you require:– Approx. 2 qt (2 l) of water

– Approx. 2 kg (4 lbs) of dishwashersalt

– Domestic dishwasher detergent

– Rinse aid formulated for domesticdishwashers

Every dishwasher is tested at the fac-tory. There will be residual water in theappliance from this test. It is not an in-dication that it has been used previ-ously.

Dishwasher saltIn order to achieve good cleaning re-sults, the dishwasher needs to operatewith soft water. Hard water results in abuild-up of calcium deposits on dishesand in the dishwasher. Water supplies with a hardness levelhigher than 4 gr/gal (4 °d) needs to besoftened. This takes place automaticallyin the integrated softener assembly. Thesoftener assembly in the dishwasher issuitable for a water hardness level of upto 73 gr/gal (70 °d).

The softener assembly requires dish-washer salt. Depending on the water hardness level(< 22 gr/gal or 21 °d), dishwasher salt isnot required if combination tablets arebeing used (see "Operation - Deter-gent").

If the water in your area is very softand consistently lower than 5 gr/gal(5 °d - German scale) you do nothave to add dishwasher salt. Theprompt to add salt will be switched offautomatically if the softener assemblyhas been programmed for this to hap-pen.

Dishwasher detergent will dam-age the softener assembly.Do not fill the salt container withdishwasher detergent (even liquiddetergent).

Use only special, coarse-graineddishwasher salt or other pure kitchensalt.Other types of salt may contain in-soluble components which can dam-age the softener assembly.


24

Filling the salt reservoir

Important! Before filling the saltreservoir with dishwasher salt for thefirst time, you must fill it with approx.2 qt (2 l) of water to enable the salt todissolve.Once the dishwasher has been usedfor the first time, there is always suf-ficient water in the reservoir.

Remove the lower basket from thewash cabinet and unscrew the saltreservoir cap.

Water will run out of the reservoirwhen the cap is removed.It should therefore only be removedin order to refill the salt reservoir.

Fill the reservoir with approx. 2 qt (2 l)of water (first use only).

Place the funnel provided over thesalt reservoir and carefully fill with saltuntil the reservoir is full. The saltreservoir holds approx. 4 lbs (2 kg) ofsalt depending on the brand used.

Clean any excess salt from aroundthe reservoir opening and then screwthe cap on again firmly.

Immediately after filling the salt reser-voir, run the QuickIntenseWash pro-gram with the Short programming op-tion selected and without any dishesin the dishwasher to remove anytraces of salt from the wash cabinet.


25

Salt refill indicator

Fill the salt reservoir with dishwashersalt for reactivation when Refill saltappears in the display. If it appearsduring a program, wait until the endof the program.

Confirm with OK.

The salt refill indicator will go out.

Risk of corrosion! Immediately after filling the saltreservoir, run the QuickIntenseWashprogram with the Short programmingoption selected and without anydishware in the dishwasher to re-move any traces of salt from thewash cabinet.

After the salt reservoir has been filled,the refill indicator may still appear in thedisplay if the salt concentration has notyet reached the correct level. If this isthe case, confirm again with OK.

The salt refill indicator will be turned offif you have programmed the dishwasherfor a water hardness below 5 gr/gal(5 °d).

If you only ever use Tab products inyour dishwasher, you can switch offboth refill indicators for salt and rinseaid if you wish (see "Settings menu,Switching off the refill indicators").

If you switch to using detergent thatdoes not contain salt or rinse aid, itis important to remember to adddishwasher salt and rinse aid and toswitch the indicators back on.


26

Rinse aidRinse aid is needed to prevent spottingon dishes and glassware. The rinse aidis filled in the reservoir and the setamount will be automatically dosed.

Filling the rinse aid reservoir withdetergent will damage the reservoir.Only pour rinse aid formulated forresidential dishwashers into thereservoir.

When using "Tab" detergents rinseaid is not needed.

Adding rinse aid

Press the button on the lid of therinse aid reservoir in the direction ofthe arrow until the flap springs open.


27

Add rinse aid only until it is visible inthe opening.

The rinse aid reservoir holds approx.3.7 oz. (110 ml).

Close the flap firmly so that it clicksinto place. Otherwise water can enterthe rinse aid reservoir during a pro-gram.

Wipe up any spilled rinse aid. Thisprevents over-foaming occurring dur-ing the next program.

You can adjust the rinse aid dosagefor best results (see "Settings menu -Rinse aid").

Rinse aid indicator

When the Refill rinse aid message ap-pears in the display, the reservoir con-tains sufficient rinse aid for 2 - 3 pro-grams only.

Add rinse aid.

Confirm with OK.

The rinse aid refill indicator will go out.

If you only ever use Tab products inyour dishwasher, you can turn off bothrefill indicators for salt and rinse aid ifyou wish (see "Settings menu - Turn-ing off the refill indicators").

Loading the dishwasher

28

TipsRemove coarse food residues from thedishes.

There is no need to rinse items underrunning water!

Do not wash items soiled withash, sand, wax, grease, or paint inthe dishwasher. These will damagethe dishwasher.

Dishes can be loaded anywhere in thebaskets, but the following notes shouldbe observed:

– Do not place dishes or cutlery insideother pieces. They will cover eachother.

– Load the dishes so that water canaccess all surfaces. This ensures thatthey get properly cleaned.

– Make sure that all items are securelypositioned.

– Hollow items such as cups, glasses,pans, etc. must be inverted in thebasket.

– Tall, narrow, hollow items, e.g.,champagne glasses, should beplaced in the center of the basket toensure better water coverage.

– Concave items such as mugs orbowls should be placed at an angleso that the water can run off.

– The spray arms must not be blockedby items which are too tall or hangthrough the baskets. If in doubt, testfor free movement by manually rotat-ing the spray arms.

– Make sure that small items cannotfall through the holders in the bas-kets. Small items, e.g., lids, should there-fore be placed in the cutlery tray orcutlery basket (depending on model).

Some foods may contain naturaldyes, e.g., carrots, tomatoes ortomato sauce. Plastic items in thedishwasher may discolor if largequantities of these foodstuffs findtheir way into the dishwasher on thedishes. The stability of plastic itemsis not affected by this discoloration.Cleaning silver cutlery in the dish-washer may also cause plastic itemsto discolor.


29

Items not recommended for dish-washing

– Wooden cutlery, cutting boards anddishes or items with wooden parts

– Craft items, antiques, valuable vases,and decorative glassware

– Plastic items which are not heat-re-sistant: the high temperatures in thedishwasher may cause them to meltor lose shape.

– Copper, brass, tin and aluminumitems may discolor or become matt.

– Colors painted over a glaze may fadeafter a number of washes.

– Delicate glassware and glasswarecontaining lead crystal: clouding mayoccur over time.

Please note:

Silverware previously cleaned with asilver polish may still be damp or spot-ted at the end of a program, where wa-ter has not run off smoothly. It mayneed to be rubbed dry with a soft cloth.

Silver which has been in contact withfoods containing sulphur can discolor.These include egg yolk, onions, mayon-naise, mustard, fish, and marinades.

Aluminum components (e.g.,range hood grease filters) must notbe cleaned with a commercial or in-dustrial cleaning agent.These may damage the material.

Tip: When purchasing new dishes andcutlery, make sure they are dishwasher-safe.

Glass care

– Clouding may occur on glasses afterfrequent washing. If delicate glass-ware is washed in the dishwasher,ensure that only very low tempera-tures are used (see program chart), ora special glass-care program is used(depending on model). This will re-duce the risk of clouding.

– Purchase glassware which is dish-washer-safe (e.g., Riedel glassware).

– Use detergents with glass protectiveadditives.


30

Loading examples

Loading for 10 standard place settings with cutlery tray

Upper basket Lower basket

Cutlery tray (depending on model)


31

Loading for 16 standard place settings with cutlery tray


Cutlery tray (depending on model)


32

Loading for 10 standard place settings with cutlery basket


Cutlery basket


33

Loading for 13 standard place settings with cutlery basket


Cutlery basket


34

FlexAssistThe yellow FlexAssist components indi-cate which elements of the baskets fordishes and cutlery tray are moveable.They also act as grips and have sym-bols embossed on them to show whatthe moveable parts are used for.

Upper basket

For safety reasons, do not oper-ate the dishwasher without the upperand lower baskets in place (exceptwhen running the Tall items program,if available).

Use the upper basket for small, light-weight and delicate items such ascups, saucers, glasses, dessertbowls, etc. Shallow pans or casserole dishes canalso be placed in the upper basket.

Long items such as soup ladles, mix-ing spoons, and long knives shouldbe placed lying down across the frontof the upper basket.

Cup rack

Using the yellow lever , lift the cuprack upwards to make room for tallitems.

Glasses can be arranged along the po-sitioning rail of the cup rack to givethem some support during the program.

Lower the cup rack and lean theglasses against it or double stacksmaller pieces.


35

Hinged spikes

The rows of spikes can be lowered tomake more room for larger items suchas casserole dishes.

Press the yellow lever downwards and then lower the spikes .

XXL cup rack (depending on model)

The cup rack can be set at two differentwidths so that it can also accommodatelarge cups.

Pull the cup rack upwards and click itback into position at the requiredwidth.


36

Glassware rail

The glassware rail is designed to holdglasses with long stems securely.

Lower the glassware rail with the yel-low lever and lean tall glassesagainst it.

You can also move one of the side in-serts in the cutlery tray to make moreroom for tall glasses (see "Cutlery, 3Dcutlery tray").

Adjusting the height

You can set the glassware rail at twodifferent heights.

Pull the rail upwards and click it backinto position at the required height.

Use the lower position for small glassesand tumblers.

Use the higher position for tall glassesand glasses with stems.


37

Adjusting the upper basket

In order to gain more space for talleritems the upper basket can be adjustedon three levels with 3/4" (2 cm) betweeneach level.

The upper basket can also be set at anangle with one side high and the otherside low. Make sure, however, that thebasket can slide smoothly in and out ofthe cabinet.

Pull the upper basket out.

To raise the upper basket:

Lift the basket until it clicks intoplace.

To lower the upper basket:

Pull upwards on the levers at eitherside of the upper basket.

Adjust the basket to the desiredheight and then push the levers se-curely back down into position.

Depending on the setting of the upperbasket, the following plate dimensionscan be accommodated.

Dishwashers with cutlery basket (see data plate for model number)

Upperbasketadjust-ment

Plate in inches (cm)Upper basket Lower

basketADA Full-size

Upper 7 7/8" (20)

9 7/16" (24)

12 3/16"(31)13

3/4" (35*)Middle 8 11/16"

(22)10 1/4"

(26)11 7/16"

(29)Lower 9 7/16"

(24)11" (28)

10 5/8"(27)

Dishwashers with cutlery tray (see data plate for model number)

Upperbasketadjust-ment

Plate in inches (cm)Upper basket Lower

basketADA Full-size

Upper 7 7/8" (15)

7 1/2" (19)

12 3/16"(31) 13

3/4" (35*)Middle 6 11/16"

(17)8 1/4"

(21)11 7/16"

(29)Lower 7 1/2"

(19)9 1/16"

(23)10 5/8"

(27)

* When tilted, plates of up to 13 3/4" (35 cm)can be accommodated (see "Lower bas-ket").Depending on the setting of the upperbasket, a variety of plate dimensionscan be accommodated.


38

Lower basket

For larger and heavier items such asplates, serving platters, saucepans,bowls, etc.Glasses, cups and small items suchas saucers can also be placed in thelower basket. Do not place thin, deli-cate glassware in the lower basket.

Place large platters and dishes in thecenter of the lower basket.

When tilted, plates up to 13 3/4" (35cm) in diameter can be accommodated.

Removable MultiComfort insert

The rear section of the lower basket isused for washing cups, glasses, plates,pots and pans.

You can remove the MultiComfort insertto make more room for larger itemssuch as casserole dishes.

Removing the insert

Pull the yellow handle forwards andremove the insert.

Refitting

Fit the insert into the lower basketwith the hooks under the long cross-piece .

Press down on the insert until it clicksinto position .


39

FlexCare glass holder

Silicone padding in the FlexCare glassholder provides a stable and securehold for delicate stemware.

Stem glassware, e.g. wine glasses orchampagne flutes, can be leanedagainst the glass rack or suspendedfrom it.

The glass holder can be raised tomake more room for tall items.

You can set the glass holder at two dif-ferent heights.

Slide the glass holder to the desiredheight until the catches click intoplace at the top or bottom.

Glassware rail

The glassware rail is designed to holdglasses with long stems securely.

Lower the rail and lean tall glassesagainst it.


40

Hinged spikes

The spikes at the front are used forwashing plates, soup bowls, platters,dessert bowls, and saucers.

The spikes can be lowered to makemore room for large items, e.g. pots,pans and dishes.

Press the yellow lever downwards ,and then lower the spikes .

Bottle holder

The bottle holder can be used to washnarrow items, e.g., milk and baby bot-tles.

If the bottle holder is not needed, liftit up and fold the sides down ,as illustrated.


41

Pot rests and filtersYou can also wash Miele pot rests andMiele hood filters.

Select the Grates & Filters program foroptimum dishwashing results.

Protruding parts can damage thedishwasher.Load the dishwasher in such a waythat no corners protrude over theside of the basket.

Heavy and sharp wash loads candamage the coating of the basketstruts.Load pot rests and filters carefully.

Pot rests

Rust damages the dishwasher.Wash only pot rests that are undam-aged and not rusty.

Place the upper basket in the top po-sition.

Load the pot rest in the lower basket.To do so, remove the MultiComfortinsert and fold over the front row ofspikes.

Place the pot rest on the bottom ofthe basket and against the struts onone side. On the other side of thebasket, flip up the glass holder andplace this side of the pot rest on thesilicone padding of the glass holder.


42

Filters

You can wash two range hood filters inthe upper basket and two in the lowerbasket at once.If you only want to wash two filters, putthem in the top basket.

Upper basket

Lower basket

Be careful when unloading thefilters. At the end of the program, thefilters may still contain hot water.


43

Cutlery

3D cutlery tray+ (depending on model)

Arrange the cutlery in the tray asshown.

To make unloading much easier, cutleryshould be grouped in zones, one forknives, one for forks, one for spoons,etc.

Spoon heads should be placed in con-tact with at least one of the serrated re-tainers on the base of the cutlery tray toensure that water runs off them freely.

For optimum cleaning results arrangespoons with the inner part facing thecenter of the cutlery tray.

The upper spray arm must not beblocked by items which are too big.

The side sections of the tray can bemoved into the middle using the yellowgrips in order to accommodate tallcookware in the upper basket (see also"Upper basket - Glassware rack").

If spoon handles do not fit between theholders, lay them the other way round.


44

You can use the yellow slide to adjustthe height of the middle section of thecutlery tray to make more room for largeitems of cutlery, such as servingspoons and ladles.

Both rows of spikes in the middle sec-tion of the cutlery tray can be flippedover to make room for larger pieces ofcutlery.

Raise the spikes and then flip themover .


45

Cutlery basket (depending on model)

The cutlery basket can be placed any-where on the front rows of spikes in thelower basket.

To avoid the risk of injury, knives andforks should be placed with the han-dles upwards in the basket. However,cutlery placed handle down in thebasket will come out cleaner anddrier.

Place small items of cutlery in the in-dividual slots on three sides of thecutlery basket.

Cutlery insert for the cutlery basket

Use the insert supplied for heavilysoiled items of cutlery. The insert sepa-rates the items so that they can bemore easily accessed by water.

Fit it onto the cutlery basket if re-quired.

Insert cutlery with the handles facingdownwards.

Distribute them evenly along the in-sert.

Operation

46

Detergent

Only use detergents formulatedfor domestic dishwashers.

Active ingredients

Modern detergents contain various ac-tive ingredients, the most important ofwhich are:

– Complexing agents to prevent calcifi-cation.

– Alkalis to aid the removal of dried-onsoiling.

– Enzymes to break down starch andloosen protein.

– Oxygen-based bleaching agents toremove colored stains (e.g., tea, cof-fee, tomato sauce).

Most dishwasher detergents are mildlyalkaline and contain enzymes and oxy-gen-based bleaching agents.

There are different types of detergent:

– Powder and liquid gel detergents.These detergents allow you to adjustthe amount dispensed according tothe amount of load and level of soil-ing.

– Tab detergents. These are suitable formost levels of soiling.

You can also buy Tab products (see"Options, DetergentAgent", if applica-ble). In addition to detergent, these productscontain rinse aid and salt substitutes.They are available as "3 in 1" or whenthey also contain other componentssuch as glass and stainless steel pro-tective additives and enhanced cleaningpower, as "5 in 1", "7 in 1", "All in 1"etc. Refer to the manufacturer's packagingas to whether Tab products are suitablefor the water hardness level in yourarea. Please note that the cleaning and dry-ing results of Tab detergents can varygreatly.

For optimum cleaning and drying re-sults, use Miele dishwasher detergentand add Miele salt and Miele rinse aidseparately.

Operation

47

Detergent dosage

Follow the dosage recommended bythe manufacturer on the packaging.

Unless directed otherwise, use onedetergent tab or add 1 1/4 - 2 table-spoons (20 - 30 ml) detergent tocompartment II, depending on thelevel of soiling. With very heavy soil-ing you can also add a small amountof detergent to compartment l.

Tabs may not dissolve completelywhen the "QuickIntenseWash" pro-gram (if available) is used.

Use only the recommended amountof detergent. Continued use of toomuch detergent may cause machinedamage.

Dishwasher detergents cancause burning in the nose, mouth,and throat if swallowed, or inhibitbreathing.Avoid inhaling or swallowing dish-washer detergent. Keep childrenaway from detergent. Keep detergentout of the reach of children. Keepchildren away from the dishwasher when the dooris open. There could still be deter-gent residues in the dishwasher. Onlyadd detergent just before starting theprogram and lock the door with thechild lock (depending on model).

Operation

48

Adding detergent

Press the opening catch on the deter-gent dispenser. The flap will springopen.

The flap is always open at the end of aprogram.

Add the required amount of detergentand close the flap.

Make sure that the detergent packag-ing is properly closed after use toavoid it getting damp and becominglumpy.

Dispensing aid

Compartment I holds a maximum of 2teaspoons (10 ml), Compartment II holds a maximum of3.5 tablespoons (50 ml) of detergent.

The marks in compartment II indicatethe levels of approximately 1 ¼ and 2tablespoons (20 and 30 ml) respec-tively. The marks indicate the approxi-mate fill level in ml when the door isopen in a horizontal position.

Operation

49

Turning on Turn on the water supply if it is turned

off.

Open the door.

Make sure the spray arms are not ob-structed.

Press the button for at least 2 sec-onds.

The program selected will appear brieflyin the display and the appropriate indi-cator light will come on.Then, the display will show the esti-mated program duration for the pro-gram selected.

Selecting a programChoose your program according to thetype of load and the degree of soiling.

The different programs and their usesare described in the Program Over-view chapter.

Use the program selection button to select the program required.

The indicator light of the selected pro-gram will come on.

Additional programs can be selectedusing the Additional option.

Use the program selection button to select the Additional option.

The first of the additional programs willappear in the display.

Use the arrow buttons to selectthe program required.

During the course of the program, youcan use OK to display the name of theprogram which is currently running.

You can now select program options(see "Options").

If any program options are selected, theappropriate indicator lights will alsolight up.

Operation

50

Starting a program Start the program by closing the door

within four seconds of the last pressof a button.

The program will begin.

The Optical Interface comes on to showthat a program has been started.

If you do not close the door withinfour seconds, the indicator light ofthe selected program will flash andthe message Press OK to start will ap-pear in the display.The program cannot be started untilyou press the OK button and closethe door within four seconds.

A program should only be canceledin the first few minutes, if at all. Oth-erwise important program stagescould be omitted.

Time displayThe estimated duration of the programselected appears in hours and minutesin the display before the program be-gins. During the program, the time leftuntil the end of the program can only beviewed with the door open.

Each program phase is indicated by asymbol:

Pre-wash / Soak

Wash

Interim rinse

Rinse cycle

Drying

Finish

The program duration displayed mayvary with the same program. It is influ-enced by, among other things, the wa-ter temperature at each intake, the re-activation process, the softener assem-bly, the type of detergent, the amountof dishes, and the amount of soiling.

When a program is selected for the firsttime, the display will show the averageprogram duration for a cold water in-take.

The times shown in the program over-view refer to standard test loads andtemperatures.

Each time a program is run, the elec-tronic module calculates the programduration required depending on thetemperature of the water taken into thedishwasher and the amount of dishes.

Operation

51

Energy managementTo save energy, the dishwasher willswitch off automatically 10 minutes af-ter the last time a button has beenpressed or after the end of the program(see "Settings menu - Optimizestandby").

Press the button to switch thedishwasher back on.

The dishwasher will not switch offwhile a program or the FlexiTimer isrunning or if there is a fault.

At the end of the programAt the end of a program, the In-opera-tion indicator light will be visible flashingslowly with the door shut. The buzzermight also be sounding.

The program has finished when Endappears in the display and the door hasopened slightly (if applicable).

In the QuickIntenseWash program, thedoor will not open until a few minutesafter the program has finished.

The drying fan may continue to run fora few minutes at the end of the pro-gram.

Open the door fully so that the doorlocking pins retract again.

You can now empty the dishwasher.

The In-operation indicator light will goout 10 minutes after the end of the pro-gram if the door is closed.

If you have deactivated the auto-matic door opening function (see"Settings menu, AutoOpen"), butwould still like to open the door atthe end of the program, make surethat you open the door fully.Otherwise steam from the dish-washer could damage the edge ofthe counter because the fan is nolonger running.

Operation

52

Turning off the dishwasherAt the end of a program:

Open the door.

The dishwasher can be switched offat any time using the button.

Switching the dishwasher off during aprogram stops the program.

Turning the dishwasher off during therun-up to a delay start time (FlexiTimer)will also stop the process.

If the dishwasher is not going to beused for a longer period of time, e.g.,while on vacation, the water supplyshould be turned off.

Unloading the dishwasherDishes tend to break and chip moreeasily when they are hot. Allow thedishes to cool until they are comfortableenough to handle before unloadingthem.

The dishes will cool much faster if youopen the door when the program hasended.

First unload the lower basket, then theupper basket, and finally the cutlery tray(depending on model). This will prevent water drops from theupper basket and cutlery tray from fall-ing onto the dishes in the lower basket.

Operation

53

Interrupting a programThe program will be interrupted as soonas you open the door.After four seconds, the indicator light ofthe selected program will flash and themessage Continue with OK will appear inthe display.

Press the OK and close the doorwithin four seconds.

The program will continue from thepoint at which it was interrupted.

Water in the dishwasher may behot. Danger of scalding!Only open the door if absolutely nec-essary and exercise extreme cautionwhen doing so. Before closing thedoor again, leave it ajar for approx.20 seconds. This will enable the tem-perature in the wash cabinet to set-tle. After that, press the OK andclose the door within four seconds.

Changing a program

If the detergent dispenser flap has al-ready opened, do not change theprogram.

If a program has already started andyou wish to change it, proceed as fol-lows:

Open the door.

Turn the dishwasher off with the button.

Turn the dishwasher on again with the button.

Select the desired program.

Start the program by closing the doorwithin four seconds.

The Optical Interface comes on to showthat a program has been started.

Options

54

OptionsYou can select and deselect the optionsbefore starting the program using theappropriate buttons and the display

Open the door.

Turn the dishwasher on with the button.

The indicator light next to the programselected will come on.

Select a program.

Press the button for the option youwant.

The indicator light for the relevant but-ton will come on if the option is avail-able for the program selected.

If the option is not compatible with theprogram selected, a message to this ef-fect will appear in the display.

In this instance, confirm the messagewith OK.

Start the program by closing thedoor.

The option selected will remain activefor that particular program until the set-ting is changed.

Short

The Short option reduces the durationof programs in which this option isavailable by up to 30% (see "Programoverview").

In order to achieve optimum cleaningresults, energy consumption may in-crease slightly with this option.

When used in combination with theQuickIntenseWash program, the Shortoption results in a wash program with-out drying or automatic opening of thedoor (if available).

Extra economical

The Extra Economical option reducesthe energy consumption of programs inwhich this option is available by up to20%.

In order to achieve optimum cleaningresults, the program duration is ex-tended with this option.

Options

55

FlexiTimer with EcoStartThe FlexiTimer gives you three waysof starting the program by means of de-laying the start. You can set the starttime or the finish time of a program. Youalso have the option of taking advan-tage of time variable economy rates ofelectricity using the EcoStart function.

When using the delay start function,make sure that the detergent com-partment is dry before adding deter-gent. Wipe dry with a cloth if neces-sary. If the compartment is wet, pow-der detergent can become lumpyand stick to the dispenser, with theresult that it is not fully dispensed.Do not use liquid detergent when se-lecting delay start, as it can run intothe dishwasher before it is required.

Open the door.

Switch the dishwasher on with the button.

Select the desired program.

Press the button.

The indicator light will light up.

You can use the arrow buttons toselect the Start at, Finish at, or EcoStartfunction or Back .

Confirm selection of the function youwant with OK.

The set time will appear and the hournumber block will be highlighted.

You can now enter the time you wantusing the arrow buttons and con-firm with OK.

If, while you are setting the time, you donot press any buttons for several sec-onds, the display will revert to the previ-ous menu. You will then have to enteryour settings again.

If you open the door for more thanfour seconds before the start time isreached, the message Continue with OKappears in the display. Press the OKbutton and close the door within fourseconds to restart the FlexiTimer.

Options

56

Start at

With the Start at function, you set theexact time at which you want the pro-gram to start.


The hour will be saved and the minutenumber block will be highlighted.

Use the arrow sensors to set theminutes and confirm with OK.

The saved start time for the programselected will appear in the display.The indicator light will come on.

Close the door within four seconds.

When the set time is reached, the pro-gram selected will begin automatically.

Finish at

With the Finish at function, you set thetime at which you wish the program toend.




The estimated start time for the pro-gram selected will appear in the display.The indicator light will come on.


A message will appear in the display ifthe program cannot be completed bythe set finish time because it has toolong a running time.

The program will start automaticallywhen the estimated start time isreached.

Options

57

EcoStart

The EcoStart function allows you to takeadvantage of time variable economyrates of electricity. Before you can usethis option, you must set up to threeelectricity rate time zones (see "Settingsmenu - EcoStart"). You then set the latest time at which theprogram selected should end. The dishwasher will start automaticallyin the cheapest rate zone within thetime set.




The estimated start time for the pro-gram selected will appear in the display.The indicator light will come on.


The selected program will start auto-matically during the most cost effectivetime zone. It will finish at the latest bythe set finish time.

Changing or deleting set times

You can change the set times or theprogram before the start time in the dis-play is reached.

Open the door.

Press the button.

Use the arrow buttons to selectthe setting you want to change andconfirm with OK.

Use the arrow buttons to selectthe Change or Delete function andconfirm with OK.

After confirming the Change function,you can change the set time.

After confirming the Delete function, theprogram duration will appear in the dis-play for the selected program. The indicator light will go out and theindicator light for the selected programwill come on.

Start the program by closing thedoor.

If you open the door for more thanfour seconds before the start time isreached, the message Continue with OKappears in the display. Press the OKbutton and close the door within fourseconds to restart the FlexiTimer.

Program overview

58

Program When to use Program sequence

Pre-wash

Mainwash

Interimrinse

Finalrinse

Drying

°F/°C °F/°C

Normal 1) Program for regular use to completelywash a full load of normally soileddishes with the ability to adjust en-ergy and water consumption basedon the soil load of the dishes.

Asneeded

117-140/47-60

X 140/60

X

Pots &Pans

For heavily soiled dishes and normallysoiled pots,pans and utensils withdried on residue; use 20% more de-tergent than recommended.

2X 167/75

X 136/58

X

China& Crystal

For temperature sensitive glasswareand lightly soiled dishes, use 50% de-tergent recommended. GlassCareprogram for temperature-sensitiveglasses and dishes with light soiling.Use 50% of the detergent amount.

X 113/45

X 136/58

X

QuickIntense-Wash

"Quick program" for standard dishessoiling that has not dried on.

149/65

X 140/60

X

SaniWash To sanitize dishes, e.g. baby bottles,cutting boards and preparation dish-ware.

156/69

2X 158/70

X

1) This program is the most efficient in terms of its combined energy and water consumptionfor cleaning normally soiled crockery.This program is used for energy labeling purposes.

Program overview

59

Consumption 2) Duration 2)

Energy Water

Cold water Hot water Gallons/Liters Cold water Hot water

50°F/10°C 120°F/49°C 50°F/10°C 120°F/49°C

kWh kWh h:min h:min

1.02 1.11 3.2/12.1 2:19 2:00

1.30 1.55 3.8/14.5 3:24 3:07

0.85 1.05 3.4/13.0 2:23 2:03

1.15 1.25 3.0/11.5 1:15 0:58

1.45 1.65 3.3/12.5 2:50 2:31

2) Values quoted are in accordance with 10 CFR 430 / C373-04. In practice there may bevariations to these figures due to variable conditions and data recorded by the sensors.Durations shown will reflect your household conditions.Selecting program options will also affect consumption levels and program durations (see"Programme options").The energy consumption with a hot water supply includes the energy used to heat thewater (exception: EnergySaver, if available).

Program overview

60

Program When to use Program sequence

Pre-wash

Mainwash

Interimrinse

Finalrinse

Drying

°F/°C °F/°C

Rinse &Hold

To rinse dishes when a completeprogram is not needed.

X

Extra Quiet Extra quiet program for mixed loadswith standard, slightly dried-on foodresidue with a longer program dura-tion.

115/46

X 131/55

X

Grates &Filters

Wash program for cleaning Mielegrates, the Miele griddle plate, andMiele ventilation hood filters.

2X 167/75

X 136/58

X

Clean Machine

Special cleaning program to removegrease deposits from the dish-washer.

167/75

2X 158/70

X

Program overview

61

Consumption 2) Duratiion 2)

Energy Water

Cold water Hot water Gallons/Liters Cold water Hot water

50°F/10°C 120°F/49°C 50°F/10°C 120°F/49°C

kWh kWh h:min h:min

0.01 0.20 1.1/4.0 0:14 0:14

0.80 1.00 2.5/9.5 4:35 4:28

1.45 1.70 3.8/14.5 3:48 3:25

1.95 2.25 5.7/21.5 2:43 2:11

2) Values quoted are in accordance with 10 CFR 430 / C373-04. In practice there may bevariations to these figures due to variable conditions and data recorded by the sensors.Durations shown will reflect your household conditions.Selecting program options will also affect consumption levels and program durations (see"Programme options").The energy consumption with a hot water supply includes the energy used to heat thewater (exception: EnergySaver, if available).

Settings menu

62

Adjusting default values

Opening the Settings menu Switch the dishwasher on with the button if it is switched off.

Use the program selection button to select the Additional option.

The first of the additional programs willappear in the display.

Select the Settings menu option withthe arrow buttons and confirmwith OK.

The first option in the Settings menu willappear in the display.

For more information about the func-tion of the display, see "Display".

Use the arrow buttons to selectthe menu option you want to changeand confirm your selection with OK.

Sub-menu options which have alreadybeen selected will have a check be-side them.

To exit a sub-menu, use the ar-row buttons to select Back andconfirm with OK.

The display will revert to the menuabove.

Language The display can be set to appear in oneof several different languages.

You can change the language in thedisplay via the Language sub-menu.

Select the language you want as wellas the country, if appropriate, andconfirm with OK.

The flag after the word Language acts as a guide if a language whichyou do not understand has alreadybeen set.If this is the case, keep selecting theoption which has a flag after it untilyou reach the Language sub-menu.

Time of dayYou can select either a 24-hour or 12-hour clock.

The current time of day must be set be-fore you can use the "FlexiTimer" pro-gramming option.

Setting the clock format

Select the Clock format menu option.

Select the setting you want and con-firm with OK.

Setting the time of day

Select the Set menu option.

Set the hour with the arrow but-tons and confirm with OK.Then set the minutes and confirmwith OK.

The time of day has now been saved.

Settings menu

63

Water hardnessThis appliance is fitted with a softenerassembly.The dishwasher must be programmedfor the water hardness in your area.

– The dishwasher must be pro-grammed to the correct water hard-ness for your area.

– Your local water authority will be ableto advise you of the water hardnesslevel in your area.

– Where the water hardness fluctuatese.g. between 10 - 16 gr/gal (10 -15 °d), always program the dish-washer to the higher value (16 gr/galor 15 °d in this example).

Select the water hardness level foryour area and confirm your selectionwith OK.

A check will appear beside the waterhardness which has been set.

°d gr/gal °f Display

1 1 2 1

2 2 4 2

3 3 5 3

4 4 7 4

5 5 9 5

6 6 11 6

7 7 13 7

8 8 14 8

9 9 16 9

10 10 18 10

°d gr/gal °f Display

11 11 20 11

12 13 22 12

13 14 23 13

14 15 25 14

15 16 27 15

16 17 29 16

17 18 31 17

18 19 32 18

19 20 34 19

20 21 36 20

21 22 38 21

22 23 40 22

23 24 41 23

24 25 43 24

25 26 45 25

26 27 47 26

27 28 49 27

28 29 50 28

29 30 52 29

30 31 54 30

31 32 56 31

32 33 58 32

33 34 59 33

34 35 61 34

35 36 63 35

36 38 65 36

37-45 39-47 66-80 37-45

46-60 48-63 82-107 46-60

61-70 64-73 109-125 61-70

Settings menu

64

Rinse aidYou can adjust the rinse aid dosage forbest results. The rinse aid dosage is set in stagesfrom 0 to 6. It is set to 3 at the factory.

If spots appear on dishware and glass-ware:

– Increase the rinse aid dosage.

If clouding or smearing appears ondishware and glassware:

– Decrease the rinse aid dosage.

Select the setting you want and con-firm your choice with OK.

EcoStartIn order to run your dishwasher in themost economical way, you can use theEcoStart option to take advantage ofyour electricity supplier's time variablerates (see "Options - FlexiTimer withEcoStart"). With this option selected, your dish-washer will start automatically at yourelectricity supplier's cheapest ratetimes.

To use this option, you must first set upto three electricity rate time zones inwhich the dishwasher can start. Youcan allocate different priorities to thesetime zones. The time with the cheapestelectricity rate will be given Priority 1.

Contact your electric supplier to findout the times of the cheapest electricityrates.

Once the electricity rate times havebeen set, you can use the EcoStart op-tion to set the latest finish time requiredfor each program. The dishwasher will then start automati-cally in the cheapest electricity rate timeand the program will end at the latest atthe finish time set.

Settings menu

65

Setting the electricity rate times

Before you can use the EcoStart option,you must set at least one electricity ratetime.

Use the arrow buttons to selectthe electricity rate time (R1-R3) youwant to set and confirm with OK.

The start of the electricity rate time se-lected will appear in the display and thehour number block will be highlighted.

Use the arrow buttons to set thehours and minutes for the start timeand confirm both with OK.

The end of the electricity rate time se-lected will appear in the display and thehours number block will be highlighted.

Use the arrow buttons to set thehours and minutes for the end timeand confirm both with OK.

The electricity rate time will be savedand its priority will appear in the display.

Use the arrow buttons to set thepriority you want and confirm withOK.

Confirm the message with OK.

The electricity rate time will be acti-vated.

Changing the electricity rate times

You can change the start, finish or pri-ority of an electricity rate time.

Use the arrow buttons to selectthe electricity rate time (R1-R3) youwant to change and confirm with OK.

Select the setting you want to changeand confirm with OK.

Use the arrow buttons to changethe setting and confirm with OK.


The change will be saved.

Settings menu

66

Deleting the electricity rate times

You can delete the settings for anelectricity rate time and in doing sodeactivate the EcoStart option for thistime zone.

Use the arrow buttons to selectthe electricity rate time (R1 - R3) youwant to delete and confirm with OK.

For example, select Delete R1 andconfirm with OK.

For example, select Delete R1? andconfirm with OK.

The settings for the electricity rate timeselected will be reset.


The electricity rate time has now beendeleted.

SoakYou can use this function to loosendried-on food residues in the programselected.Once activated, this function will becarried out with all programs until youdeactivate it.If you are using powder dishwasher de-tergent, add approx. 5 g to compart-ment I.


Settings menu

67

Pre-RinseYou can use this function to removeeasily loosened food residues in theprogram selected.Once activated, this function will becarried out with all programs until youdeactivate it.


BrightnessThere are seven different display bright-ness settings.

Select the brightness you want andconfirm this with OK.

VolumeA sequence of buzzer tones will soundat the end of the program or if there is afault as long as the buzzer has been ac-tivated.

Buzzer in the event of a fault

The buzzer in the event of a fault willsound four times at intervals with ashort pause between each set of tones.

The buzzer which sounds when thereis a fault cannot be deactivated.

Buzzer at the end of a program

The buzzer at the end of a program willsound four times at intervals with ashort pause between each set of tones.

The volume of the buzzer which soundsat the end of the program can be set toone of seven stages. If no volume is se-lected, the buzzer is switched off.

Select the Buzzer tone option.

Use the arrow buttons to set thevolume required and confirm your se-lection with the OK button.

Keypad tone

An buzzer tone sounds each time a but-ton is pressed.

The volume of the keypad tone can beset to one of seven stages. If no volumeis selected, the keypad tone is switchedoff.

Use the arrow buttons to set thevolume required and confirm your se-lection with the OK button.

Settings menu

68

Refill indicatorsIf you consistently use a Tab detergentand the refill indicators for salt and rinseaid are bothering you, you can deacti-vate them if you wish.


If you switch to using detergent thatdoes not contain salt or rinse aid, itis important to remember to adddishwasher salt and rinse aid and toswitch the indicators back on.

Check filtersYou can adjust the interval at which themessage to remind you to check the fil-ters appears. You can set an interval between 30 and60 program cycles.

The "Check filters" message is set atthe factory to appear after every 50 pro-gram cycles.

Select the interval you want and con-firm this with OK.

Settings menu

69

AutoOpenAt the end of programs with a dryingphase, the door will open automaticallya little in order to help the dryingprocess (see "Program overview").In the QuickIntenseWash program, thedoor will open a few minutes after theprogram has finished.

This function can be deactivated ifwished.


If you have deactivated the auto-matic door opening function andwould like to open the door as soonas the program has finished, makesure that you open the door fully.Otherwise steam from the dish-washer could damage the edge ofthe counter because the fan is nolonger running.

Optimize StandbyThe dishwasher is supplied with the Op-timize standby function switched on asstandard.

To save energy, the dishwasher willswitch off automatically a few minutesafter the last time a button has beenpressed or after the end of a program.

The dishwasher will not switch off inthe event of a fault.

Optimize Standby can be switched off ifyou prefer. If you do this the durationbefore the dishwasher switches off au-tomatically increases to 6 hours. Doingthis will increase energy consumption.


Settings menu

70

Software versionYou can display the electronic softwareversion of your dishwasher electronicsfor technical support purposes.

Confirm the display with OK.

Showroom program

For demonstration purposes only.

The dishwasher is fitted with variousdemonstration programs for showroomuse.

– Demo modeDemonstration program for show-rooms.

– Demo with sound This program activates the circulationpump to demonstrate the sound ofthe dishwasher.

– Demo Drying Plus The door will open automatically.

– BrilliantLightThe interior lighting is on constantly.

Factory default settingsYou can reset all dishwasher settings tothe factory default settings.

WLAN module settings (where applica-ble) have to be reset separately (see"Settings -Miele@home - Module set-tings").

Select Reset and confirm with OK.

Closing the Settings menuYou can exit the Settings menu usingClose.

Select Close and confirm with OK.

The program selected will appear in thedisplay briefly and the indicator light forthe program selected will come on.

Cleaning and care

71

Check and clean your dishwasherregularly. This will help avoid prob-lems and faults.

All surfaces are susceptible toscratching.Contact with unsuitable cleaningagents can alter or discolor all sur-faces.

Cleaning the wash cabinetGenerally, the wash cabinet is selfcleaning if the correct amount of deter-gent is used.

If, however, there are limescale orgrease deposits in the wash cabinet,these can be removed with a specialcleaning agent (available from Miele).Follow the instructions on the packag-ing.

If you mainly use low temperature pro-grams (< 120°F/50 °C), there is a risk ofbacteria and unpleasant odors buildingup in the wash cabinet. To prevent thishappening the dishwasher will automat-ically increase the temperature in the fi-nal rinse of the selected program afterseveral programs using low tempera-tures have been run.

Clean the filters in the wash cabinetregularly.

Cleaning the door and the doorsealBacteria could build up on the door sealand the sides of the dishwasher door asthese surfaces are outside the washcabinet and are not accessed andcleaned by the spray arm jets.

Wipe the door seals regularly with adamp cloth to remove food deposits.

Wipe off any food or drink residueswhich may have dripped onto thesides of the dishwasher door beforeclosing it.

Cleaning the control panel The control panel should only be

wiped with a damp cloth.

Cleaning the indicator reflectorpanelThe indicator reflector panel for the Op-tical Interface / TimeControl function(depending on model) is situated in thecover plate underneath the counter.

The indicator reflector panel shouldonly be wiped with a damp cloth or asuitable cleaning agent designed foruse on plastic.

Cleaning and care

72

Cleaning the door front

If soiling remains longer, it mayhappen that the surfaces can be-come discolored or changed.Remove any soiling immediately.

Clean the front with a solution ofwarm water and a little dishwashingliquid applied with a soft sponge.Wipe the surfaces dry using a softcloth.

Glass cleaners may be used toclean the exterior. However do notallow them to sit or "puddle", thiscan cause damage to the surface.Remove the cleaner promptly.

To better maintain your applianceavoid the following:

– Cleaning products containing soda,ammonia, acid, or chloride

– Descaling agents

– Abrasive cleaning products, such asscouring powder, scouring liquid, orpumice stones,

– Cleaners containing solvents

– Stainless steel cleaners

– Dishwasher cleaner

– Oven cleaners

– Glass cleaner

– Hard, abrasive brushes or sponges,e.g., pot scourers, brushes orsponges which have been previouslyused with abrasive cleaning agents

– Eraser sponges

– Sharp metal scrapers

– Steel wool

– Steam cleaning appliances

Cleaning and care

73

Filter systemThe filter system in the base of thewash cabinet prevents food from beingredeposited on dishes. It also protectsthe circulation pump from damagecaused by foreign objects.

This dishwasher must not beused without all the filters in place!

Collection of coarse soil may cause thefilters to clog. The level of soiling andtime it takes before the filters needcleaning will vary depending on use.

The message Check filters will appear inthe display after every 50 program cy-cles (factory default setting).

You can set the interval for the "Checkfilters" message to appear to a valuebetween 30 and 60 program cycles (see"Settings menu - Check filters").

Check the filter system.

Clean it if necessary.

Then confirm the message with OK.

The message will go out.

Filter system Turn the dishwasher off.

Turn the handle counter-clockwise torelease the filter system .

Lift the filter system out of the dish-washer . Remove any coarse parti-cles and rinse the filter well underrunning water. Use a nylon brush if necessary.

Ensure that coarse soil does notget into the circulation system andcause a blockage.

Cleaning and care

74

To clean the inside of the filter, the flapmust be opened:

Press catches together in the di-rection of the arrows as shown, andopen the filter .

Rinse all the filters under running wa-ter.

Then close the flap so that the catchengages.

Replace the filter system so that it liesflat in the base of the wash cabinet.

Then turn the handle clockwise untilboth arrows point towards eachother. This will lock the filter system inplace.

Take care when you are fittingthe filter system that it is secured inposition correctly.Otherwise coarse soil could get intothe circulation system and cause ablockage.

Cleaning and care

75

Cleaning the spray armsParticles of food can get stuck in thespray arm jets and bearings. The sprayarms should therefore be inspected andcleaned regularly (approx. every 4 - 6months).

Turn the dishwasher off.

Remove the spray arms as follows:

Take out the cutlery tray (if your dish-washer is fitted with one).

Push the top spray arm upwards toengage the inner ratchet. Then un-screw the spray arm.

Push the middle spray arm upwards to engage the ratchet. Then un-screw the spray arm .

Remove the lower basket.

Pull the lower spray arm firmly up-wards to remove it.

Use a pointed object to push the foodparticles that are stuck in the sprayarm jets into the spray arm.

Rinse the spray arms thoroughly un-der running water.

Replace the spray arms and checkthat they rotate freely.

Frequently Asked Questions

76

With the help of the following guide, minor faults in the performance of the appli-ance, some of which may result from incorrect operation, can be put right withoutcontacting Miele Service. This will save time and money.

The following guide may help you to find the reason for a fault, and to correct it.You should, however, note the following:

Unauthorized or incorrect repairs could cause personal injury or damage tothe appliance.Repair work to electrical appliances must only be carried out by a suitably qual-ified and competent person in strict accordance with current local and nationalsafety regulations. The manufacturer cannot be held liable for unauthorizedwork.

Technical problems

Problem Possible cause and solution

The dishwasher doesnot start.

The door is not properly closed. Push the door firmly shut.

The dishwasher is not plugged in. Insert the plug.

The circuit breaker has tripped. Reset the fuse (see data plate for the correct fuse

rating).The dishwasher is not switched on. Turn the dishwasher on with the button.

The dishwasher stopsduring a program.

The circuit breaker has tripped. Reset the fuse (see data plate for the correct fuse

rating). If the circuit breaker trips again, contact Miele Ser-

vice.

After the program hasstarted, the Optical In-terface is not visible.

The indicator reflector panel was not correctly fitted. Refit the indicator reflector panel correctly (see the

installation plan).

The buzzer is sounding. The program will notstart. The In-operation indica-tor light is not lit up.

The door has not closed properly, because it had notbeen fully opened after the door had been openedautomatically. Open the door fully so that the door locking pins

retract again. Then close the door.


77


The Optical Interface isflashing quickly.The buzzer is sounding.One of the followingfaults appears in thedisplay:

Before fixing the fault: Turn the dishwasher off with the button.

Fault FXX There may be a technical fault.

After a few seconds: Turn the dishwasher back on. Select the desired program. Close the door.

If the error message is displayed again, there is atechnical fault. Contact Miele Service.

Waterproof The WaterProof System has reacted. Turn off the water supply. Contact Miele Service.

Fault F78 A fault has occurred in the circulation pump. Turn the dishwasher off for at least 30 seconds

with the button. Turn the dishwasher back on. Select the desired program. Close the door.

If the error message is displayed again, there is atechnical fault. Contact Miele Service.


78

Water intake fault


The In-operation indica-tor light is flashingquickly.The buzzer is sounding.One of the followingfaults appears in thedisplay:

Open water supply The water supply is turned off. Turn on the water supply fully.

Intake Before fixing the fault: Turn the dishwasher off with the button.

There is a problem with the water intake. Turn on the water supply fully and start the pro-

gram again. Clean the water intake filter (see "Frequently asked

questions"). The water pressure at the intake is lower than 4.35

psi.Contact a plumber.

The following messageappears in the displayduring the Energy Saverprogram: Intake temp. low

The intake water has not reached the required tem-perature of 120°F (45°C) (see "Water connection, Wa-ter intake"). Start the program again. If the fault message appears again, select a differ-

ent program.


79

Water drainage fault


The Optical Interface isflashing quickly.The buzzer is sounding.The following fault ap-pears in the display: Drain


There is a problem with the water intake. There might be water in the wash cabinet. Clean the filter system (see "Cleaning and care -

Filter system"). Clean the drain pump (see "Frequently asked

questions"). Clean the non-return valve (see "Frequently asked

questions"). Remove any kink or loop in the drain hose.


80

General problems


The Optical Interface isflashing quickly.The warning buzzer issounding.The indicator light ofthe selected programand the message Con-tinue with OK will appearin the display.The dishwasher doesnot start or the Flex-iTimer stops running.

The safe mode of the dishwasher was activated.The following takes place:

– If you do not close the door within four seconds ofthe last press of a button at program start

– If the door is open for longer than four secondsduring a program or within the delay start time

Press the OK and close the door within four sec-onds.

Detergent residue is leftin the dispenser at theend of a program.

The dispenser was still damp when detergent wasadded. Make sure the dispenser is dry before adding de-

tergent.

The dispenser covercannot be closed.

Detergent residue is blocking the latch. Remove the detergent residue.

The inside of the doorand/or the interior wallsare wet after a programhas finished.

This is caused by the drying system and does not in-dicate a fault. The moisture will dissipate after awhile.

Water remains in thewash cabinet at the endof a program.


The filter system in the wash cabinet is clogged. Clean the filter system (see "Cleaning and care -

Filter system").The drain pump or non-return valve is blocked. Clean the drain pump or the non-return valve (see

"Frequently asked questions").The drain hose is kinked. Remove the kink.


81

Noises


There is a knockingnoise in the wash cabi-net.

A spray arm is hitting the dishes. Interrupt the program, and rearrange the items

which are obstructing the spray arm.

There is a rattling noisein the wash cabinet.

Dishes is moving around in the wash cabinet. Interrupt the program and rearrange loose pieces.

A foreign object (e.g., a cherry pit) has becomelodged in the drain pump. Remove the foreign object from the drain pump

(see "Maintenance - Cleaning the drain pump andnon-return valve").

There is a knockingnoise from the waterpipe

This may be caused by the installation or the diameterof the water pipe. This has no influence on dishwasher function. If in

doubt, contact a suitably qualified plumber.


82

Poor cleaning results


The dishes are notclean.

The dishes were not loaded correctly. See notes in "Loading the dishwasher".

The program was not powerful enough. Select a more intensive program (see "Program

overview").Not enough detergent was dispensed. Use more detergent, or change your detergent.

Items are blocking the path of the spray arms. Rearrange the items so that the spray arms can ro-

tate freely.The filter system in the base of the wash cabinet isnot clean or is not correctly fitted. This may cause the spray arm jets to get blocked. Clean and/or fit the filter system correctly. Clean the spray arm jets if necessary (see "Clean-

ing and care - Cleaning the spray arms").The non-return valve is open and blocked. Dirty waterhas flowed back into the wash cabinet. Clean the drain pump and the non-return valve

(see "Frequently asked questions").

Smearing appears onglassware and cutlery.There is a bluish sheenon the surface of glass-ware; film can be wipedoff.

The rinse aid dosage is set too high. Reduce the dosage (see "Settings menu - Rinse

aid").


83


Dishes is not dry or cut-lery and glasses arespotty.

The rinse aid dosage is set too low or the rinse aidreservoir is empty. Replenish the reservoir, increase the dosage, or

change the brand of rinse aid (see "Before usingfor the first time - Rinse aid").

Dishes was taken out of the cabinet too soon. Leave it in for longer (see "Operation").

Combination tabs have been used which have im-paired drying performance. Change your detergent, or replenish the rinse aid

(see "Before using for the first time - Rinse aid").

Glasses have a brown-ish-blue discoloration;the deposit cannot bewiped off.

Detergent deposits. Switch to another detergent.

Glasses are dull anddiscolored; the depositcannot be wiped off.

The glassware is not dishwasher-safe. The surfacesare affected. There is no remedy.

Purchase glassware which is dishwasher-safe.

Tea or lipstick stainshave not been com-pletely removed.

The wash temperature of the selected program wastoo low. Select a program with a higher wash temperature.

The bleaching effect of the detergent is too low. Switch to another detergent.

Plastic parts are discol-ored.

Natural dyes, e.g., from carrots, tomatoes, or ketchupmay be the cause. The amount of detergent used orits bleaching effect was not sufficient to deal with nat-ural dyes. Use more detergent (see "Operation - Detergent").

Discoloration is irreversible.


84


White residue is visibleon dishes and cutlery,clouding occurs onglassware; this film canbe wiped off.

The rinse aid dosage is too low. Increase the dosage (see "Settings menu, Rinse

aid").The salt reservoir is empty. Fill the salt reservoir (see "Before using for the first

time, Dishwasher salt").The salt reservoir cap has not been screwed on cor-rectly. Replace it, making sure that it screws back on cor-

rectly.An unsuitable Tab detergent has been used. Change your detergent.

The softener assembly is programmed too low for thewater hardness level. Program the softener assembly to a higher water

hardness level (see "Settings menu, Water hard-ness").

There are rust stains onthe cutlery.

The affected items are not corrosion resistant. There is no remedy.

Purchase cutlery which is dishwasher-safe.A program was not run after dishwasher salt wasadded. Traces of salt have got into the wash cycle. Always run the QuickIntenseWash program with

the Short programming option selected and with-out any dishes in the dishwasher after addingdishwasher salt.

The salt reservoir cap has not been screwed on cor-rectly. Replace it, making sure that it screws back on cor-

rectly.

Frequently asked questions

85

Cleaning the drain pump andnon-return valveIf the water has not been pumped awayat the end of a program, the drain pumpor the non-return valve might beblocked. They are, however, easy toclean.

Disconnect the dishwasher from theelectrical supply. Turn off the dish-washer and withdraw the plug.

Take the filter system out of the washcabinet (see "Cleaning and care,Cleaning the filters").

Scoop the water out of the wash cab-inet using a suitable container orutensil.

Press the catch for the non-returnvalve inwards .

Tilt the non-return valve inwards untilit is released .

Rinse it thoroughly under running wa-ter and remove any dirt from the non-return valve.

The drain pump is located underneaththe non-return valve (see arrow).

Remove all foreign objects from thedrain pump (glass or bone splinters). Before returning the non-returnvalve, check that the drain pump isnot blocked. Spin the impeller severaltimes in both directions to check forobstructions.

Carefully reinsert the non-return valveand secure it with the locking clamp.

Make sure the locking clampclicks into place!

Be careful not to damage anydelicate components when cleaningthe drain pump and the non-returnvalve.

Customer service

86

RepairsFor problems that you cannot resolveon your own, please contact:

– your Miele dealer or

– Miele Service

The telephone number for Miele islisted at the back of these instruc-tions.

In the event of a fault which you cannotcorrect yourself please contact theMiele Service Department at the phonenumber on the back of this booklet.

WarrantyFor more information, please refer to theincluded warranty.

MieleCare (USA only)MieleCare, our Extended Service Con-tract program, gives you the assuranceof knowing that your appliance invest-ment is covered by 5 years of worry freeownership. MieleCare is the only Extended ServiceContract in the industry that guaranteesrepairs by a Miele Authorized ServiceProvider using genuine Miele parts.Only genuine Miele parts installed byfactory trained professionals can guar-antee the safety, reliability, andlongevity of your Miele appliance.

Please note that unless expressly ap-proved in writing by Miele’s Service de-partment, Extended Service Contractsoffered by other providers for Mieleproducts will not be recognized byMiele. Our goal is to prevent unautho-rized (and untrained) service personnelfrom working on your Miele products,possibly doing further damage to them,you and/or your home.

To learn more about MieleCare Ex-tended Service Contracts, please con-tact your appliance dealer or visit usonline at: http://www.mieleusa.com

Optional accessories

87

Dishwasher detergent and rinse aid, aswell as cleaning and care products, areavailable as optional accessories.All the products are designed for usewith Miele dishwashers.

These and many other useful productscan be ordered from a Miele dealer orvia the Miele Webshop (see end of thisbooklet for contact details).

Dishwasher detergent, rinseaid, and saltWhen you decide to buy a Miele dish-washer, you choose excellent qualityand performance. However, ensuringthat your dishwasher always deliversthe best possible results will also de-pend on your choice of dishwasher de-tergent, rinse aid, and dishwasher salt,as cleaning results can vary dependingon the brand used. With Miele products, you can be sure ofoptimum results as these products havebeen specially designed for Miele dish-washers.

Detergent tabs

– Sparkling results even with stubbornfood deposits

– Combination product with other com-ponents such as rinse aid, salt, andglass protection additives

– Phosphate-free - kind to the environ-ment

– Water-soluble wrapping - no need tounwrap

Powder detergent

– With active oxygen for thoroughcleaning

– With enzymes which are effectiveeven in low temperature programs

– With glass protection against corro-sion

Rinse aid

– For sparkling glasses

– Helps dishware to dry

– With glass protection against corro-sion

– Specially designed cap for accurate,easy dispensing

Dishwasher salt

– Prevents lime scale on dishware andin the appliance

– Extra coarse-grained

Optional accessories

88

Dishwasher care productsMiele cleaning and care products pro-vide optimum care for your dishwasher.

Dishwasher cleaner

– Cleans the dishwasher effectivelyand thoroughly

– Removes grease, bacteria, and un-pleasant odors

– Ensures excellent dishwashing re-sults

Dishwasher descaler

– Removes heavy lime scale deposits

– Mild and gentle with natural citricacid

Dishwasher conditioner

– Removes odors, lime scale, and lightdeposits

– Maintains the elasticity and leaktightness of the seals

Dishwasher freshener

– Neutralizes unpleasant odors

– Fresh, pleasant lime and green teascent

– Easy to attach to the dishwasherbasket

– Very economical, lasts for 60 washcycles

89

Installation Instructions

Please refer to the Installation Diagram supplied with these instructions.To comply with IEC sound testing protocols, please contact Miele for additionalinstructions.

Information is subject to change. Please refer to our website to obtain the mostcurrent product specification, technical & warranty information.

Electrical connection

90

Installation, repairs and other workby unqualified persons could be dan-gerous.Check that the voltage, frequencyand fuse rating shown on the dataplate match the household mainssupply.The power outlet must be accessibleafter installation. Do not use an ex-tension cord to connect the dish-washer to the mains. Danger of over-heating! See data plate on the rightside of the door.A damaged power cord must only bereplaced with a genuine Miele cordby a Miele service technician.

Grounding instructions

THIS APPLIANCE MUST BEGROUNDED.

In the event of a malfunction or break-down, grounding will reduce the risk ofelectric shock by providing a path ofleast resistance for the electrical cur-rent. This appliance is equipped with acord having an equipment groundingconductor and a grounding plug. Theplug must be plugged into an appropri-ate outlet that is installed and groundedin accordance with all local codes andordinances.

Improper connection of the equip-ment grounding conductor can resultin electric shock.Do not modify the plug provided withthe appliance; if it will not fit the out-let, have a proper outlet installed bya qualified electrician.If there is any question concerningthe proper electrical connection orgrounding of this appliance to thepowersupply, please consult a li-censed electrician or call Miele’sTechnical Service Department:USA: 1-800-999-1360CDN: 1-800-565-6435

SpecificationsThe dishwasher comes equipped with a4 ft (1.2 m) powercord (measured fromthe rear of the dishwasher) with amolded plug for connection to 120 V,60 Hz, 15 A grounded receptacle.

Electrical connection

91

Hardwired electrical connectionIt is possible to hardwire this applianceto an existing power cable.

CAUTION: Before servicing, discon-nect the power supply by either re-moving the fuse, shutting off thepower main or manually "tripping"the circuit breaker.Installation work and repairs shouldonly be performed by a qualifiedtechnician in accordance with all ap-plicable codes and standards. Re-pairs and service by unqualified per-sons could be dangerous and themanufacturer cannot be held respon-sible.Before connecting the appliance tothe power supply, make sure that thevoltage and frequency listed on thedata plate correspond with thehousehold electrical supply. Thisdata must correspond to preventmachine damage. Consult an electri-cian if in doubt.

GROUNDING INSTRUCTIONS

THIS APPLIANCE MUST BEGROUNDED.

This appliance must be connected to agrounded metal, permanent wiring sys-tem, or an equipment-grounding con-ductor must be run with the circuit con-ductors and connected to the equip-ment-grounding terminal or lead on theappliance.

Prior to making a hardwire connec-tion to the terminal, remove the pow-ercord. Otherwise there will be a riskof electric shock from the attachedplug.

An existing flexible supply cord or cableshall have a minimum thickness ofAWG 14.120 V, 60 Hz, 15 A fuse ratingBlack wire (live): connect to LWhite wire (neutral): connect to NGreen wire (ground): connect to

After attaching the permanent powersupply cord, check that all screws onthe terminal block and the strain re-lief are tightened.

Water connection

92

Water intake

Water in the dishwasher mustnot be used as drinking water.

– The dishwasher may be connected toa cold or hot water supply up to amaximum of 140°F/60°C. For reduced energy consumption, werecommend a cold water connection.We recommend connection to a hotwater supply only if it is economical,e. g. a solar-powered supply with re-circulation line. When connected to ahot water supply, all program phaseswhich would otherwise be carried outwith cold water will be carried outwith hot water

– The Energy Saver program (if available)requires a hot water supply between115°F/45°C (minimum) and140°F/60°C (maximum). The higher the water intake tempera-ture, the better the cleaning and dry-ing results.

– The inlet hose is approx. 5 ft long. A5 ft long flexible metal hose (pressuretested to 2030 psi) is available as anoptional accessory if required.

– A faucet with a 3/8" male threadmust be provided on site.

– This appliance is constructed tocomply with ANSI/ASSE 1001 // IEC/EN/DIN 61770 // VDE 0700 Part 600,and may be connected to a suitablesupply without an extra non-returnvalve if national regulations permit.

– Water pressure: Must be between4.5 - 145 psi (0.3 - 10 bar) If the waterpressure is lower than this, the faultmessage Intake will appear in the dis-play (see "Frequently asked ques-tions"). If the water pressure is toohigh, a pressure relief valve must befitted.

After connecting the dishwasher tothe water supply, check that the wa-ter intake is airtight.

To avoid any damage to the ap-pliance, the dishwasher must only beoperated when it is connected to afully vented plumbing system.

The intake hose must not beshortened or damaged in any way asit contains electrical components(see illustration).

Water connection

93

Drainage– The machine comes equipped with a

built-in non-return valve on the dis-charge side to prevent waste waterfrom flowing back into the dish-washer.

– Take the drain line of the dishwasherand attach the drain line as high aspossible under the counter rim of thekitchen sink before connecting theend to the drain. The loop will serveto prevent a backed up drain or largevolume of water in the sink from si-phoning back into the dishwasher.

– The dishwasher is supplied with ap-prox. 5' 11" (1.5 m) of flexible drainhose with an internal diameter of7/8" (22 mm).

– The drain hose can be extended us-ing extensions and adapters. Thedrainage length must not be longerthan 13' 1 1/2" (4 m) and the deliveryhead must not exceed 3' 3 3/8" (1 m).

– If the hose is to be directly fitted tothe drainage outlet on site, use thehose clip supplied (see installation di-agram).

– The hose can be directed to the leftor the right of the appliance.

– The on-site connector for the drainhose can be adapted to differentwidths of hose. If the connector pro-trudes too far into the drain hose, itwill need to be shortened. Otherwisethe drain hose may become blocked.

– The drain hose must not be short-ened.

Make sure that there are no kinksin the hose, and that it is notsquashed or stretched.

After servicing the appliance, ensurethat the drain does not leak.

Venting the drain

If the on-site drain connection is situ-ated lower than the guide path for thebottom basket rollers in the open door,the drain must be vented. Otherwise asiphoning effect during a program cancause the appliance to empty itself ofwater.

To vent: open the dishwasher doorfully.

Pull the lower spray arm firmly up-wards to remove it.

Cut off the top of the vent valve in thewash cabinet.

Sound emission testing

94

Prerequisites for sound emission testsLoad the dishwasher with 16 standard place settings and use the Normal pro-gram.

Setup for sound emission testsThe dishwasher must be set up according to the following specifications.

Install the dishwasher into an analyzing unit.

Secure the front panel.


95

Push the provided fleece strips (depending on model) under the toe-kick until itis flush with the appliance feet .

Push the toe-kick into place in such a way that it is flush with the door front .


96

Remove the protective film from the provided insulating strip (depending onmodel) .

Push the insulating strip into the front top edge of the toe-kick .

9 Independence WayPrinceton, NJ 08540Phone:Fax:www.mieleusa.com

U.S.A.Miele, Inc.

National Headquarters

Please have the model and serial numberof your appliance available whencontacting Technical Service.

CanadaImporterMiele Limited

Headquarters and Miele Centre

800-843-7231609-419-4298

Technical Service & SupportPhone:Fax:[email protected]

161 Four Valley DriveVaughan, ON L4K 4V8www.miele.ca

800-999-1360888-586-8056

Customer Care CentrePhone:

[email protected]

800-565-6435905-532-2272

International HeadquartersMiele & Cie. KGCarl-Miele-Straße 2933332 GüterslohGermany

M.-Nr. 10 546 840 / 02en-US

G 6780 / G 6785

Documents

Operating Instructions Dishwasher - Miele · 2017-02-21 · IMPORTANT SAFETY INSTRUCTIONS 7 Correct use This dishwasher is intended for use in domestic households and similar residential