Embed Size (px)
Citation preview
Airless Line Striper
ENGLISHOPE
RATI
NG A
ND M
AINT
ENAN
CE
INST
RUCT
ION
OPE
RATI
NG A
ND M
AINT
ENAN
CE
INST
RUCT
ION
PAINTING EQUIPMENT
Ed.
005
11 -
10
1
English
ABC
ED
FG
IH
JLM
N
OP
Q
R
TS
U
WV
Z
INTRODUCTION.................................................... p.1WORKING PRINCIPLE ......................................p.2TECHNICAL DATA ..............................................p.2DESCRIPTION OF THE EQUIPMENT ...............p.3CONTROLS DESCRIPTION ..............................p.4TRANSPORT AND UNPACKING .......................p.5SAFETY RULES .................................................p.5SETTING-UP ......................................................p.6WORKING ..........................................................p.8CLEANING AT THE END OF THE WORK .........p.9ROUTINE MAINTENANCE ................................p.9PROBLEMS AND SOLUTIONS .........................p.10CORRECT PROCEDURE OF DECOMPRESSION ............................................p.11REPLACEMENT OF THE PUMPINGGROUP'S GASKETS .........................................p.12
CHARGING THE BATTERY ...............................p.12CLEANING AND/OR REPLACEMENT OFTHE PRESSURE TRANSMITTER .....................p.13COMPLETE PRESSURE CONTROLDEVICE REF. 16350 ...........................................p.14COMPLETE PUMPING REF. 16100 ....................p.16FILTER GROUP .................................................p.18RECIRCULATING-SAFETY VALVEGROUP REF.16400 ............................................p.19DRIVE ASSEMBLY .............................................p.20SUCTION SYSTEM ............................................p.2250L TANK ............................................................p.23ACCESSORIES ..................................................p.24
HIGH PRESSUREPAINTING EQUIPMENT
HIGH PRESSUREPAINTING EQUIPMENT
WE ADVISE THE USE OF THIS EQUIPMENT ONLY BY PROFESSIONAL OPERATORS.ONLY USE THIS MACHINE FOR USAGE SPECIFICALLY MENTIONED IN THIS MANUAL.
Thank you for choosing a LARIUS S.R.L. product.As well as the product purchased,
you will receive a range of support servicesenabling you to achieve the results desired,
quickly and professionally.
It indicates an accident risk or serious damage to equipment if
this warning is not followed.
It indicates a fire or explosion risk if this warning is not
followed.
It is obligatory to wear suitable clothing as gloves, goggles and face shield.
Read this operator’s manual carefully before using the equipment. An
improper use of this machine can cause injuries to people or
things.
It indicates important recommendations
about disposal andrecycling process
of products in accordance with
the environmental regulations.
2
Engl
ish
AB
C
B
K-2
MOTOR POWER
TRACTION ENGINE POWER
MAX. WORKING PRESSURE
MAX. DELIVERY
SUPPLY
WEIGHT
WEIGHT WITH BATTERIES
LENGTH
WIDTH
HEIGHT
1 kW (1,3 Hp)
0,6 kW (0,8 Hp)
200 bar
2 L/min
24 V
185 Kg
260 Kg
(A) 1800 mm
(B) 1100 mm
(C) 800 mm
DATI TECNICI
A WoRKING PRINCIPLE
The unit LARIUS K-2 is defined “piston pump”. This pump is used for high pressure painting without air (from this process derives the term “airless”). The pump is controlled by an motor coupled with a reduction gear. A cam shaft and a connecting rod allow to obtain the reciprocating motion necessary to the working of the “pumping group” diaphram. The piston movement produces a “depression”.
The product is sucked, pushed towards the pump outlet and then sent to the gun through the flexible hose. A mechanical device allows to adjust and control the pressure of the material coming out of the pump. A safety valve avoiding overpressure, guarantees the total reliability of the equipment.
3
English
11
8
1
2
12
3713
910
4
5
6 8
C
PoS.
1
2
3
4
5
6
7
DESCRIPTIoN oF THE EQUIPMENT
Pressure control knob
Reduction casting
Suction Tube
High pressure hose
Airless gun
Product tank
Suction filter
Description PoS.
8
9
10
11
12
13
High pressure manometer
Airless manual gun
Trigger safety clamp
Battery charger
Drain valve
Recirculation tube
Description
4
Engl
ish
AV IND
PUSH
SToP
D1
D3D2
D6 D5
D7 D4
D8
D9
D CoNTRoLS DESCRIPTIoN
D1) Steerage lever. Pulling the lever the straight only "mode" will be unlocked
allowing the machine to run.
D2) Internal gun operating lever. Pulling the lever the gun placed at the internal side will
spray.
D3) Pull the lever to release the motors brake.
D4) LED Indicates whether the power to the panel is on or off.
D5) Key-operated selector switch Used to switch on machine.
Steerage lever
Motor brake release
Gun control lever
D6) Indicator Indicates the charge in the electrical battery.
D7) Adjustment knob Used to progressively adjust the machine’s running speed.
D8) Direction selector Allows the user to select the machine’s advancement direction;
stops the machine’s movement if pressed..
D9) Speed
5
English
E
F
TRANSPoRTAND UNPACKING
• The packed parts should be handled as indicated in the symbols and markings on the outside of the packing.
• Before installing the equipment, ensure that the area to be used is large enough for such purposes, is properly lit and has a clean, smooth floor surface.
• The user is responsible for the operations of unloading and handling and should use the maximum care so as not to damage the individual parts or injure anyone.
To perform the unloading operation, use only qualified and trained personnel (truck and crane operators, etc.) and also suitable hoisting equipment for the weight of the installation or its parts.
Follow carefully all the safety rules. The personnel must be equipped with the necessary
safety clothing.
• The manufacturer will not be responsible for the un-loading operations and transport to the workplace of the machine.
• Check the packing is undamaged on receipt of the equipment. Unpack the machine and verify if there has been any damage due to transportation.
In case of damage, call immediately LARIUS and the Shipping Agent. All the notices about possible damage or anomalies must arrive timely within 8 days at least from the date of receipt of the plant through Registered Letter to the Shipping Agent and to LARIUS.
• The disposal of packaging materials is a customer’s competence and must be performed in accordance with the regulations in force in the country where the plant is installed and used.It is nevertheless sound practice to recycle packaging materials in an environment-friendly manner as much as possible.
SAFETY RULES
• THE EMPLOYER SHALL TRAIN ITS EMPLOYEES ABOUT ALL THOSE RISKS STEMMING FROM ACCI-DENTS, ABOUT THE USE OF SAFETY DEVICES FOR THEIR OWN SAFETY AND ABOUT THE GENERAL RULES FOR ACCIDENT PREVENTION IN COMPLIAN-CE WITH INTERNATIONAL REGULATIONS AND WITH THE LAWS OF THE COUNTRY WHERE THE PLANT IS USED.
THE BEHAVIOUR OF THE EMPLOYEES SHALL
STRICTLY COMPLY WITH THE ACCIDENT PREVEN-TION AND ALSO ENVIRONMENTAL REGULATIONS IN FORCE IN THE COUNTRY WHERE THE PLANT IS INSTALLED AND USED.
Read carefully and entirely the following in-structions before using the product. Please save these instructions in a safe place
The unauthorised tampering/replacement of one or more parts composing the machine, the use of accessories, tools, expendable materials other than those recommended by the manu-facturer can be a danger of accident.
The manufacturer will be relieved from tort and criminal liability.
• KEEP YOUR WORK PLACE CLEAN AND TIDY. DISORDER WHERE YOU ARE WORKING CREATES A POTENTIAL RISK OF ACCIDENTS.
• ALWAYS KEEP PROPER BALANCE AVOIDING UNUSUAL STANCE.
• BEFORE USING THE TOOL, ENSURE THERE ARE NOT DAMAGED PARTS AND THE MACHINE CAN WORK PRO-PERLY.
• ALWAYS FOLLOW THE INSTRUCTIONS ABOUT SAFETY AND THE REGULATIONS IN FORCE.
• KEEP THOSE WHO ARE NOT RESPONSIBLE FOR THE EQUIPMENT OUT OF THE WORK AREA.
• NEVER EXCEED THE MAXIMUM WORKING PRESSURE INDICATED.
• NEVER POINT THE SPRAY GUN AT YOURSELVES OR AT OTHER PEOPLE. THE CONTACT WITH THE CASTING CAN CAUSE SERIOUS INJURIES.
• IN CASE OF INJURIES CAUSED BY THE GUN CASTING, SEEK IMMEDIATE MEDICAL ADVICE SPECIFYING THE TYPE OF THE PRODUCT INJECTED. NEVER UNDER-VALUE A WOUND CAUSED BY THE INJECTION OF A FLUID.
• ALWAYS DISCONNECT THE SUPPLY AND RELEASE THE PRESSURE IN THE CIRCUIT BEFORE PERFORMING ANY CHECK OR PART REPLACEMENT OF THE EQUIPMENT.
• NEVER MODIFY ANY PART IN THE EQUIPMENT. CHECK REGULARLY THE COMPONENTS OF THE SYSTEM.
REPLACE THE PARTS DAMAGED OR WORN.
6
Engl
ish
High pressure hose
G
• TIGHTEN AND CHECK ALL THE FITTINGS FOR CONNEC-TION BETWEEN PUMP, FLEXIBLE HOSE AND SPRAY GUN BEFORE USING THE EQUIPMENT.
• ALWAYS USE THE FLEXIBLE HOSE SUPPLIED WITH STANDARD KIT. THE USE OF ANY ACCESSORIES OR TOOLING OTHER THAN THOSE RECOMMENDED IN THIS MANUAL, MAY CAUSE DAMAGE OR INJURE THE OPERATOR.
• THE FLUID CONTAINED IN THE FLEXIBLE HOSE CAN BE VERY DANGEROUS. HANDLE THE FLEXIBLE HOSE CAREFULLY. DO NOT PULL THE FLEXIBLE HOSE TO MOVE THE EQUIPMENT. NEVER USE A DAMAGED OR A REPAIRED FLEXIBLE HOSE.
The high speed of travel of the product in the hose can create static electricity through di-scharges and sparks. It is suggested to earth the equipment.
The pump is earthed through the earth cable of the supply. The gun is earthed through the high pressure flexible hose. All the conductors near the work area must be earthed.
• NEVER SPRAY OVER FLAMMABLE PRODUCTS OR SOL-VENTS IN CLOSED PLACES.
• NEVER USE THE TOOLING IN PRESENCE OF POTEN-TIALLY EXPLOSIVE GAS.
Always check the product is compatible with the materials composing the equipment (pump, spray gun, flexible hose and accessories) with which it can come into contact. Never use
paints or solvents containing halogen hydrocarbons (as the methylene chloride). If these products come into contact with aluminium parts can provoke dangerous chemical reactions with risk of corrosion and explosion.
IF THE PRODUCT TO BE USED IS TOXIC, AVOID INHALATION AND CONTACT BY USING PROTECTION GLOVES, GOGGLES AND PROPER FACE SHIELDS
TAKE PROPER SAFETY MEASURES FOR THE PROTECTION OF HEARING IN CASE OF WORK NEAR THE PLANT.
Electrical safety precautions
• Check the "ON/OFF" switch is on the "OFF" position before connecting the cable to the mains.
• Never carry a plugged-in equipment.
• Disconnect the equipment before storing it and before per-forming any maintenance operation or replacing of acces-sories.
• Do not carry the equipment neither unplug it by pulling the electric cable.
Protect the cable from heat, oil and sharp edges.
• When the tool is used outdoors, use only an extension cable suited for outdoor use and so marked.
Never attempt to tamper with the calibre of instruments.
• Take care when the pumping rod is moving. Stop the machine whenever someone is within its vicinity.
• Repairs of the electrical equipment should only be carried out by skilled personnel, otherwise considerabledanger to the user may result.
SETTING-UPCoNNECTIoN oF THE FLExIBLE HoSE To THE GUN
• Connect the high pressure flexible hoses to the pump and the guns tightening the fittings strongly (the use of two wrenches is suggested).
NEVER use sealants on fittings threads. It is ADVISED to mount a high pressure manometer at the
pump outlet (see on page "Accessories") to read the product pressure.
• It is recommended to use the hose provided with the standard kit.
NEVER use a damaged or a repaired flexible hose.
7
English
G3
G2
G5
G4
G1
oNoFF
WASHING oF THE NEW EQUIPMENT
• The equipment has already been adjusted at our factory with light mineral oil left inside the pumping group as protection. Therefore, wash with diluent before sucking the product.
• Lift the suction pipe and dip it into the solvent tank.
• Ensure the gun (G1) is without nozzle.
• Turn the key (G2) of the equipment to the oN (I) position.• Turn clockwise the pressure control knob (G3) so as the
machine works at idle speed.
• Point the gun at the solvent tank and press the trigger so as to recover the residual solvent.
• As soon as the pump starts to over-rev turn the key to the oFF (0) position to switch off the equipment.
Absolutely avoid to spray solvents indoors. In addition, it is recommended to keep away from the pump in order to avoid the contact between the solvent fumes and the electric motor.
• Now the machine is ready. Should you use water paints, besides the solvent wash, a wash with soapy and then clean water is suggested.
• Insert the gun trigger lock and assemble the nozzle.
PREPARATIoN oF THE PAINT
• Make sure the product is suitable to be used with a spray gun.
The use of non-compliant products causes damage to the machine thus annulling the guarantee (only use specific filtered paints for airless applications).
Make sure the product to be used is compatible with the materials employed for manufacturing the equip-ment (stainless steel and aluminium). Because of that, please contact the supplier of the product.
Never use products containing halogen hydrocarbons (as methy-lene chloride). If these products come into contact with aluminium parts of the equipment, can provoke dangerous chemical reactions with risk of explosion.
• Remove the suction pipe and take away the solvent tank.
• Point the gun (G4) at a container (G5) keeping the trigger pressed (so as to drain the oil inside) till a clean solvent comes out. Now, release the trigger.
8
Engl
ish
H1
H3
H5
H2
H4H WoRKING
Delivery pipe connection
START oF THE PAINTING oPERATIoNS
• Use the tooling after performing all the SETTING UP ope-rations above described.
• Dip the suction pipe (H1) into the product tank (H2).
• Make sure the product recycles from the return tube (H5).
• Close the drain valve (turn clockwise till the valve has rele-ased).
• Now the machine carries on sucking the product till the flexible hose is full, up to the gun. Then it will stop automatically.
SPRAY ADJUSTMENT
• Slowly turn clockwise the pressure control knob to reach the pressure value in order to ensure a good atomization of the product.
• An irregular and marked spray on the sides indicates a low working pressure. On the contrary, a too high pressure causes a high fog (“overspray”) and waste of product.
• In order to avoid overthickness of paint, let the gun advance sideways (right-left) when spraying.
• Always paint with regular parallel bands coats.
• Keep a safety and constant distance between the gun and the support to be painted and also keep yourselves perpendicular to it.
NEVER point the spray gun at yourselves or at other people. The contact with the casting can cause serious injuries.In case of injuries caused by the gun casting, seek immediate medical advice specifying the
type of the product injected.
The drain valve is a safety valve too. When working at the maximum pressure available, releasing the gun trigger sudden increases of pressure can occur. In this case, the drain valve
opens automatically eliminating part of the product from the recirculating tube. Then it closes so as to go back to the first working conditions.
• Open the safety- relief valve (H3) (turn clockwise so as the pin slides on the cam track).
• Press the switch oN (I) of the equipment and turn a little the pressure control knob (H4) clockwise, so as the machine works at the idle speed.
9
English
J1
J2
I1
I2
oNoFF
• Open the safety valve to release the pressure in the circuit.
• Lift the suction pipe and replace the product tank with that of the solvent (ensure it is compatible with the product being used).
• Unscrew the gun nozzle (do not forget to clean it with sol-vent).
• Turn the key (I2) oN (I) and turn a little the pressure control knob (I1) clockwise so as the machine works till the motor starts.
• Make sure the solvent recycles the washing fluid from the
return tube.
• Close the safety valve.
• Point the gun at the product tank and, keeping the trigger pressed, release the remaining product till a clean solvent comes out. Now, release the trigger.
• Lift again the suction pipe and remove the solvent tank.
• Now point the gun at the solvent tank and press the trigger so as to recover the residual solvent.
• As the pump starts idling, press the switch oFF (0) to stop the equipment.
I CLEANING AT THE ENDoF THE WoRK
• Reduce pressure to the minimum (turn counterclockwise the pressure control knob (I1)).
• Turn the key (I2) placed on the box of the electric motor, to stop the equipment.
J RoUTINE MAINTENANCE
CHECK oN THE PACKING NUT
Daily check the packing nut is tight in order to avoid wastes but not excessively to prevent the piston from seizing and the gaskets from wearing.
• For tightening, use the wrench (J1) supplied (ref. 11503).
ALWAYS DISCoNNECT THE PoWER SUPPLY AND RELEASE THE PRESSURE IN THE PUM-PING GRoUP (open the drain valve) BEFoRE TIGHTENING THE PACKING NUT.
• Use the lubricant (J2) supplied (rif. 16325) to allow an easy sliding of the piston inside the gasket group.
Daily top up the packing nut.
Oil ring
• In case of long storage, we recommend you to suck and to leave light mineral oil inside the pumping group and the flexible hose.
Follow the washing procedure before using again the equipment.
10
Engl
ish
L PRoBLEMS AND SoLUTIoNS
SolutionCauseProblem
• The equipment does not start
• The equipment does not suck the product
• The equipment sucks but does not reach the pressure desired
• When pressing the trigger, the pressure lowers considerably
• The pressure is normal but the product is not atomized
• The atomization is imperfect
• When releasing the trigger of the gun, the equipment does not stop (the motor runs slowly and the piston rod keeps on going up and down)
• Lack of voltage;
• Breakdown of pressure transmitter;• Breakdown of motor electric control box;• The product is solidified inside the
pump;
• Suction filter clogged;• Suction ilter too fine;
• The equipment sucks air;
• Lack of product;• The equipment sucks air;• The drain valve is open;• The gaskets of the pumping group are
worn;• Suction or delivery valve dirty;
• Nozzle too big or worn;• The product is too dense;• The filter of the gun-butt is too fine;
• The nozzle is partially clogged;• The product is too dense;• The filter of the gun-butt is too fine;
• The nozzle is worn;
• The gaskets of the pumping group are worn;
• Suction or delivery valve dirty;
• Drain valve defective;
• Check the correct connection to the power supply;
• Verify and replace it, if necessary;• Verify and replace it, if necessary;• Open the drain valve to release
pressure in the circuit and stop the machine. Disassemble the pumping group and the pressure transmitter and clean;
• Clean or replace it;• Replace it with a larger-mesh filter
(with very dense products, remove the filter);
• Check the suction pipe;
• Add the product;• Check the suction pipe;• Close the drain valve;• Replace the gaskets;
• Disassemble the pumping group;
• Replace it with a smaller one;• Dilute the product, if possible;• Replace it with a larger-mesh filter;
• Clean or replace it;• Dilute the product, if possible;• Replace it with a larger-mesh filter;
• Replace it;
• Replace the gaskets;
• Disassemble the pumping group and clean;
• Verify and replace it, if necessary;
Always close the air compressed supply and unload the plant pressure before performing any check or repla-cement of pump parts (see "correct procedure of decompression").
11
English
M1
M3
M2
oNoFF
M CoRRECT PRoCEDURE oF DECoMPRESSIoN
• Insert the gun clamp (M1).• Turn the key (M2) to the oFF (0) position to stop the equip-
ment.
WARNING: If the equipment is still under pressure after performing the operations above described because of the nozzle or the flexible hose clogged, proceed as follows:• Loosen very slowly the gun nozzle.• Release the clamp.• Point the gun at the container of the product and press the trigger to release
pressure.• Loosen very slowly the fitting of connection from the flexible hose to the gun.• Clean or replace the flexible hose and the nozzle.
• Open the drain valve (M3) to release the residual pressure always clockwise.
12
Engl
ish
O1
O2
N REPLACEMENT oF THE PUMPING GRoUP’S GASKETS
• Carry out this operation after cleaning the tooling.
Always disconnect the power supply and release pressure before going on with the operations (fol-low the “correct procedure of decompression).
• Disconnect the pumping group by unscrewing the two fastening screws.
• Using a screwdriver, turn the motor till the piston rod is on its stroke lowest point.
• Extract the pumping group from the housing paying attention to the dowel pins.
• Unscrew the rigid suction pipe from the pumping group by loosening the locknut;
• Unscrew the upper packing nut;• Unscrew the suction valve and clean and/or replace its parts,
if necessary;• Extract the piston rod from the bottom;• Disassemble the piston rod and replace the gaskets group
if worn;• If necessary, remove the upper gaskets for their replace-
ment;• See the exploded view of the pumping group for the correct
assembly.
Lock nut
Dowel pins
Clamping screws
o CHARGING THE BATTERY• Pull out the plug (o1);• Connect the battery charger cables (o2) to the socket (o1);• Switch on the battery charger (o2) and wait until the machines
battery is completely charged.
The batteries must be recharged at least once a month in order to prevent them from dete-riorating.
13
English
P1
P3
P2
oNoFF
P CLEANING AND/oR RE-PLACEMENT oF THE PRES-SURE TRANSMITTER
CHECK oN THE PRESSURE TRANSMITTER
Before evaluating if the cause of the malfunction is due to the pres-sure transmitter or to the electric control box, proceed as follow:
• Check the correct connection to the power supply.
• Make sure that the key (P1) is on the oN (I) position.
• Turn a little the pressure control knob (P2) clockwise till the electric motor starts.
• In case, after these checks, the tooling does not start, verify the pressure transmitter.
• Make sure the equipment does not suck materials (remove the product tank).
• Open the drain valve (P3).
• Disassemble the pumping group as shown on the previous chapter.
Pressure sensor
Pressure pin
• Remove the pressure sensor from its housing and chek if the pin can move. If necessary, clean thoroughly.
• Check the seals (O-ring and teflon ring): if worn or "pinched", replace them.
• Disassemble the supporting block and check the microswitch operates properly by using a tester. If damaged, replace it.
• Reassemble the whole unit centering the block with the fastening screws.
• Reassemble the whole unit and start again the machine following the procedure indicating.
• If the machine does not start, check the electrical connections and the motor electric control box: if damaged, replace it.
14
Engl
ish
30
28
29
12
13
11
11
23
2725
24
22
20
17
18
16
15
15
19
26
14
10
9
8
7
6
5
4
3
2
1
Q CoMPLETE PRESSURE CoNTRoL DEVICE REF. 16350WARNING: always indicate code and quantity for each part required.
15
English
Pos. Pos.
Elastic ring
Washer
Gasket
Pin
O-ring
Antiextrusion ring
Sensor
Gas-ring
O-ring
Ball
Screws
Gasket
Cover
Cable fastener
Screws
Bush
Dowel
Screws
Microswitch
Support box
Control rod
Quill
Elastic ring
Ball
Spring
Pin
Adjusting pin
Knob
Dowel
Label
16336
16335
11955
16334
9287
16333
16331
16332
4077
96090
96028
16037
16042
16280
16312
16307
22059
16310
16313
16311
16306
16304
81017
4060
16303
16309
16315
16301
95210
16308
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Code Description Code Description
16
Engl
ish
1
2
3
56
910
11
12
13
7
8
8
4
4
14
15
16
17
18
19
20
21
22
R CoMPLETE PUMPING REF.16100WARNING: always indicate code and quantity for each part required.
* Complete gasket kit cod. 16555** Pumping maintenance kit cod. 40116
***
Pos.
Packing nut
Complete upper seals
Dowel
Assembly pins
Pumping case
Screws
Piston rod
Screws
Piston rod
Elastic pin
Ball
Nut
Complete lower seals
Union
Lock nut
O-ring
Pumping cylinder
Ball guide
Ball
O-ring
Foot valve
Pin
16109
16105
96205
16033
16101
33007
33006
16111
16110
91010
16130
16113
16115
16128
16127
16126
16112
98466
16120
16121
16129
16122
1
2
3
4
5
6
7
8
9
10
11**
12
13
14
15
16**
17
18
19**
20**
21
22
Code Description
***
17
English
System of assemblage
Upper seals
Leather cod.16155
Steel male ringcod. 16108
Red cod. 16104
White cod. 16124
Steel female ringcod. 16106
Steel male ringcod. 16116
Steel female ringcod. 16118
White cod. 16136
Red cod. 16114
cod. 16132
cod. 16105
Red cod. 16104
White cod. 16124
White cod. 16136
Red cod. 16114
cod. 16133
cod. 16115
Lower seals
18
Engl
ish
S FILTER GRoUPWARNING: always indicate code and quantity for each part required.
1
2
3
4
5
6
8
8
7
Manometer 0-400 bar code 33008
Pos.
Filter tank
Spring
Standard sieve
Standard sieve 100
Standard sieve 200
Sieve support
Gasket
Filter base
Union
Dowel
16201
96202
16205
16204
16203
16202
96203
96204
96206
96205
1
2
3
3
3
4
5
6
7
8
Code Description
19
English
1
2
43
5
6
7
8
9
10
T RECIRCULATING-SAFETY VALVE GRoUP REF. 16400
WARNING: always indicate code and quantity for each part required.
Pos.
O-ring
Valve housing
O-ring
Antiextrusion ring
Material rod
Spring
Bush
Dowel
Knob
Dowel
4033
16415
53007/3
16419
16420
16410
46409
16408
16405
90018
1
2
3
4
5
6
7
8
9
10
Code Description
20
Engl
ish
1 2
3
4
6
516
12 13
1415
7 8 9 10 11
U DRIVE ASSEMBLY
21
English
18
17
Pos. Pos.
Bearing
Connecting rod
Bush
Pin
Pad
Bearing
Screw
Gearcase
Screw
Bushing
Closing bracket
Screws
Cover
Screw
Tornado label
Dowel
Battery charger
Batteries 6V 240Ah
16024
16025
16040
16026
16028
16019
8029
16029
95623
16027
16030
81032
16031
16036
16045
16023
4605
19461
Code Description Code Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
22
Engl
ish
1
8
32
4
5 7 6
V SUCTIoN SYSTEM
Pos.
Filter
Dispersion bell
Breaker flux
Bell pipe
Pipe fitting with spring
16802
18351
18352
18353
18608
1
2
3
4
5
Codice Description Pos.
Female extension 3/8" - male 1/4"
Pipe fitting
Delivery compensation hose length
15 mt
22028
16058
18026
.
6
7
8
.
Codice Description
23
English
1
2
3
4
5
6
78
9
10
11
W 50L TANK
Pos.
CoverStainless stell fine drum filter UnionTank 50LSupportSealUnionTapUnionElbow connectorSuction tube
18249/185014182311824918246960999503230532837520833
18223/1
1234567891011
Code Description
TYPE D REF.18238
TYPE E REF.18225 N°2PZ.
TYPE F REF.18225
Type Liner
Type E
Type F
Type D
Type D
Type D
Type D
LARIETTE LINER
3000 LINER
DALì LINER
DRAGON LINER
EVEREST
K2
Type Type Ricirculation
Type A
Type A
Type A
Type B
Type B
Type C
RICIRCULATION TYPE A RIF.16680/2RICIRCULATION TYPE B RIF.95037RICIRCULATION TYPE C RIF.19191/1
24
Engl
ish
MX 750
MX 1000 E
MX 1100 E
Code 11250: AT 250 1/4"Code 11200: AT 250 M16x1,5
Code 270: FILTER 100 MESHCode 271: FILTER 60 MESH
PISTON GUNSTOCK FILTERSCode 11039: Green (30M) - Code 11038: White (60M)Code 11037: Yellow (100M) - Code 11019: Red (200M)
Code 85014: FILTER 40 MESH - Code 85012: FILTER 20 MESHCode 37215: FILTER 40 MESH inox - Code 37216: FILTER 20 MESH inox
Code 16205: FILTRO 60 MESHCode 16204: FILTRO 100 MESHCode16203: FILTRO 200 MESH
Code 217550: MX 750 - Code 217560: MX 1000 E - Code 217570: MX 1100 E
Code 18026: 1/4" - 15 mtANTIPULSATION HOSE
MANUAL GUN LX-TCode 14310: NOZZLE 4 mmCode 14311: NOZZLE 6 mmCode 14312: NOZZLE 8 mm
Z ACCESSoRIES
25
English
Code 18270: SUPER FAST-CLEAN base UE 11/16x16
Code 18280: GASKET
SUPER FAST-CLEAN TIP
SUPER FAST-CLEAN
Nozzles code
SFC07-20SFC07-40SFC09-20SFC09-40SFC11-20SFC11-40SFC13-20SFC13-40SFC13-60SFC15-20SFC15-40SFC15-60SFC17-20SFC17-40SFC17-60SFC19-20SFC19-40
SFC19-60SFC21-20SFC21-40SFC21-60SFC23-20SFC23-40SFC23-60SFC25-20SFC25-40SFC25-60SFC27-20SFC27-40SFC27-60SFC27-80SFC29-20SFC29-40SFC29-60
SFC29-80SFC31-40SFC31-60SFC31-80SFC33-40SFC33-60SFC33-80SFC39-40SFC39-60SFC39-80SFC43-40SFC43-60SFC43-80SFC51-40SFC51-60SFC51-80
PLA 1/4”+ FAST-CLEAN REVERSIBLE
TIP INCLUDEDCode 11420-11425-11430: cm 130-180-240
PLA M16x1,5+ FAST-CLEAN REVERSIBLE TIP INCLUDED
Code 11421-11426-11431: cm 130-180-240
PAINT ROLLER TELESCOPIC
Code 16988: Roller cover for
rough surfaces
Code 16997: Roller cover for
smooth surfaces
Code 16998: Roller cover for
very smooth surfaces
Code 16999: Roller cover for
semi-rough surface
Code 16780: Extension 120 - 195 cm
Due to a constant product improvement programme, the factory reserves the right to modify technical details mentioned in this manual without prior notice.
23801 CALOLZIOCORTE - LECCO - ITALY - Via Stoppani, 21Tel. (39) 0341/62.11.52 - Fax (39) 0341/62.12.43E-mail: [email protected] - Internet http://www.larius.com
PRODUCTOR:
DIRECT LINE
Tel. (39) 0341/621256Fax (39) 0341/621234
CUSTOMERS TECHNICAL SERVICE
LINE STRIPERS
LARIETTE 2000 Ref. 4220 3000 LINER Ref. 4300
STORM 4000 Ref. 4400 VIKING LINER Ref. 4800
EVEREST Ref. 4750
