Omal Thor Split Body Carbon Steel PN 16- Pascal Control ... · API 6D 2 of 53. Materials and rating in compliance with ASME B16.34 for ANSI valves and EN 12516 for PN valves Brand

Pascal Control Sdn. Bhd.

Brand OmalStandard for connecting flanges

EN 1092-1 ed. 2008; ANSI B16.5Pressure class PN16-40; ANSI 150-300Intercepted fluid

air, water, gas, petroleum and petrochemical productsStem seal TFM 1600 V-packClosing angle >7°Superficial treatment blueing

Omal Thor Split Body Carbon Steel PN 16-40 ANSI 150-300

Description

Standard Features:No protuding floating ball, full bore

Soft-seat seal TFM 1600

Operating temperature see temperature pressure diagram

Antistatic device EN12662-2

Additional seal on stem with FKM O-ring

Anti Blow-out stem

Actuator connection as per standard ISO 5211

Special Features on Request:LF2 carbon steel for low temperature execution (-40 C°)

For other flange types please contact our sales department.

Sealing in: PTFE reinforced with glass (RPTFE-GF), PTFE reinforced withcarbon-graphite (RPTFE-CF) . For other types of materials please contactour sales department

Cavity filler seatin PTFE

Mono-directional version with pressure-relief hole in the ball

Stainless steel lever

For special versions in materials different from the standard (body, ball,stem), please contact our sales department.

Stainless steel Stem nuts and springs

Superficial treatment: white zinc coating ,epoxy coatingFor other coatingplease contact our sales department

Certifications:In compliance with European Directive 97/23 EC PED

In compliance with ATEX 2014-34-EU Directive (on request)

Fugitive Emission UNI EN ISO 15848.2006

TA-LUFT VDI 2440.2000

FIRE SAFE: API 607:2005/ISO 10497:2010 - API6FA:1999

1 of 43

Engineering Standards:Body thickness in compliance with: ASME B16.34, ASME VIII div.1, EN12516.

Materials and rating in compliance with ASME B16.34 for ANSI valvesand EN 12516 for PN valves

Brand OmalSoft-seat seal TFM 1600Standard for connecting flanges

EN 1092-1 ed. 2008; ANSI B16.5Pressure class PN16-40 - ANSI 150-300Intercepted fluid

air, water, gas, petroleum and petrochemical products,aggressive fluids

Stem seal TFM 1600 V-ring packingClosing angle >7°

Omal Thor Split Body Stainless Steel PN16-40 ANSI 150-300

Description

Standard Features:Floating ball, full bore




Anti Blow-out stem


Special Features on Request:For other flange types please contact our sales department.

Sealing in: PTFE reinforced with glass (RPTFE-GF), PTFE reinforced withcarbon-graphite (RPTFE-CF). For other types of materials please contactour sales department

PTFE cavity filler seat





Certifications:In compliance with European Directive 97/23 EC PED

In compliance with ATEX 2014-34-EU Directive (on request)

Fugitive Emission UNI EN ISO 15848:2006

TA-LUFT VDI 2440:2000

FIRE SAFE: API 607:2005/ISO 10497:2010 - API6FA:1999

API 6D: certificate no 6D-1007 only for valves with ANSI face to face

Engineering Standards:Body thickness in compliance with: ASME B16.34, ASME VIII div.1, EN12516

API 6D

2 of 43


Brand OmalSoft-seat seal DEVLONStandard for connecting flanges

EN 1092-1 ed. 2008;ANSI B16.5Pressure class PN63-100 - ANSI 600Stem seal TFM 1600 V-packClosing angle >7°

Omal Stainless Split Steel Wafer PN 63-100ANSI 600

Description

Standard Features:No protuding floating ball, full bore


Intercepted fluid: air, water, gas, petroleum and petrochemical products,aggressive fluids



Anti Blow-out stem


Features on Request:For other flange types please contact our sales department.






ATEX marking and certificateON REQUEST

Certifications:In compliance with European Directive 97/23 EC PED; Fugitive EmissonISO 15848 (ISO FE BH-C03-SSA 0); TA-LUFT VDI 2440; FIRE SAFE:ISO 10497 / API 607Safety integrity level up SIL3 according to the IEC 61508In compliance with ATEX 2014-34-EU Directive , ATEX certificate ONREQUEST.


Materials and rating in compliance with ASME B16.34 for ANSI valvesand EN 12516 for PN valvesSoft-seat sealStem sealStem sealTFM 1600 V-packTFM 1600 V-pack >7°

Brand Omal

Omal Carbon Split Steel Wafer PN 63-100ANSI 600

3 of 43

Soft-seat seal DEVLONStandard for connecting flanges

EN 1092-1 ed. 2008; ANSI B16.5Pressure class PN 63-100; ANSI 600Intercepted fluid

air, water, gas, petroleum and petrochemical productsStem seal TFM 1600 V-packSuperficial treatment blueing

Description

Features:No protuding floating ball, full boreOperating temperature see temperature pressure diagramAntistatic device EN12662-2Additional seal on stem with FKM O-ringAnti Blow-out stemActuator connection as per standard ISO 5211Closing angle >7°

Features on Request:LF2 carbon steel for low temperature execution (-40 C°)

For other flange types please contact our sales department.

Sealing in: PTFE reinforced with glass (RPTFE-GF), PTFE reinforced withcarbon-graphite (RPTFE-CF) . For other types of materials please contactour sales department





Superficial treatment: white zinc coating ,epoxy coating

For other coating please contact our sales department

ATEX marking and certificateON REQUEST

Certifications:

In compliance with European Directive 97/23 EC PED; Fugitive EmissonISO 15848 (ISO FE BH-C03-SSA 0); TA-LUFT VDI 2440; FIRE SAFE:ISO 10497 / API 607

Safety integrity level up SIL3 according to the IEC 61508

In compliance with ATEX 2014-34-EU Directive , ATEX certificate ONREQUEST.


Materials and rating in compliance with ASME B16.34 for ANSI valvesand EN 12516 for PN valvesblueing

4 of 43

Brand OmalSoft-seat seal TFM 1600Standard for connecting flanges

EN 1092-1 ed. 2008; ANSI B16.5Pressure class PN16-40 - ANSI 150-300Stem seal TFM 1600 V-packIntercepted fluid

air, water, gas, petroleum and petrochemical products,aggressive fluids

Omal Stainless Steel Wafer PN 16-40 ANSI150-300

Description

Features:No protuding floating ball, full boreOperating temperature see temperature pressure diagramAntistatic device EN12662-2Additional seal on stem with FKM O-ringAnti Blow-out stemActuator connection as per standard ISO 5211Closing angle >7°

Features On Request: For other flange types please contact our sales department

Heating jacket


PTFE cavity filled seat


Stainless steel lever; stainless steel Stem nuts and springs


ATEX marking and certificate ON REQUEST

Certifications:In compliance with European Directive 97/23 EC PED; Fugitive EmissionUNI EN ISO 15848; TA-LUFT VDI 2440; FIRE SAFE: UNI EN ISO 10497 -API 607

In compliance with ATEX 2014-34-EU Directive, ATEX certificate ONREQUEST



Brand Omal

Omal VIP - Pneumatic Coaxial Valve

Description

Features:Both Double Acting and Spring Return VIP valves (either Normally Openor Normally Closed) are available in sizes ranging from 3/8” to 2”.

5 of 43

Unidirectional flow.

GAS threaded ends as per UNI/ISO 7/1 Rp - DIN 2999 (NPT threads onrequest) with control fluid connections as per NAMUR interface.

Improved fluid dynamics allow minimum pressure losses. See FlowPressure Diagram.

VIP valves can be used in any mounting position (horizontal, vertical oroblique). They can be provided with seals in NBR, FKM or EPDM:

NBR: suitable for air, gas, oils, water etc..FKM: perfectly suitable for most fluid. Unsuitable for steam.EPDM: perfectly suitable for hot water and steam. Unsuitable for mineralproducts (oils, grease, etc..).

For further information about gas, explosive fluids, material compatibilitiesetc. please contact our technical department.

Valve opening and closing can be signalled by means of externalmagnetic limit switches (to be requested on ordering the valves, as theycannot be assembled afterwards).

According to 97/23 EC “PED” - ATEX version in conformity with directive94/9/EC (to request at time of order)

Control Media:Filtered compressed air, not necessarily lubricated. At temperatures from -20°C to 0°C, use dry air. In case of lubricated air, seal compatible oilmust be used.

Air supply:

3 bar min.- 8 bar max. in Double Acting execution

4,2 bar min.- 8 bar max. in Spring Return execution.

Operating Media:

Pressure: 10 bar max, see diagram

Temperature:from -20°C to +80°C (NBR);from -20°C to +150°C (FKM);from -20°C to +150°C (EPDM).Vacuum tightness: 740 mm Hg

Brand Omal

Omal Angle Seat Valve Special Ends

Description

General Features: Body valve material: AISI 316L

Valve ends: see code plan.

Assembling is possible in all positions: upright, flat or angled.

Range available from DN 15 to DN 50 in the Double Acting versions,Spring Return N.C. from above and below the plug, Spring Return N.O.from below the plug.

The performance and the pressure’s diagrams are the same as perStandard versions but limited at PN16

On request: versions for vacuum and oxygen service

2014-34-EU ATEX configuration to request at time of order

6 of 43

Operating Media:Air, water, alcohol, oil, petroleum products, saline solutions, steam, etc.(as long as compatible with AISI 316L or PTFE).

Pressure from 0 to 16 bar (steam from 180°C, from 0 to 10 bar)depending on the size and model chosen (see catalogue page: from 31 to34).

Temperature from –10°C to 180°C.

Max. viscosity 600 cst (mm2/s).

Control Media:Driving media: compressed air, lubricated or dry, gas or neutral media.

Ambient temperature: -10°C to +60°C

Brand Omal

Omal Angle Seat Valve

Description

General Features:Threaded valve ends, as per ISO 228/1 and ISO 7/1 – other typesavailable on request.

Assembling is possible in all positions: upright, flat or angled.

Range available from 3/8” to 2” in the Double Acting versions, SpringReturn N.C. from above and below the plug, Spring Return N.O. frombelow the plug.

According to 97/23 EC “PED”

ATEX version in conformity with directive 2014-34-EU (to request at timeof order)

The variations in the actioning of the valve, the several combinations andthe possibility to intercept the fluid from above or below the plug, originatemultiple versions of the automatic valve.

In the table below are indicated the standard versions with the mainparameters.

On the basis of the kind of valve and the variations of pressure ?P thatmust be intercepted, the necessary control pressure can be individuated,and consequently, the code for the corresponding valve.

Operating media:Air,water, alcohol, oil, petroleum products, saline solutions, steam, etc. (aslong as compatible with AISI 316 or Bronze RG5).

Pressure from 0 to 16 / 25 bar (steam from 180°C, from 0 to 10 bar)depending on the size and model chosen (see following pages).

Temperature from –10°C to 180°C.

Max. viscosity 600 cst (mm2/s).

Control media

Driving media: compressed air, lubricated or dry, gas or neutral media.

Ambient temperature: -10°C to +60°C

7 of 43

Brand Omal

Omal Aluminium Spring Return (SR) Type

Description

Technical Features:Torque from 15 Nm to 4000 Nm.Mounting flange according to EN ISO 5211F03 - F04 - F05 - F07 - F10 - F12 - F14 - F16.In compliance with EN 15714-3Rotation angle 90°Torque: the return torque depends on spring action only notwithstandingthe air supply. The spring is provided in four different sizes (see table).The code numbers after the letters SR, always correspond to thebreakaway torque in Nm by 5,6 bar air supply.The actuator automatic closing takes place in clockwise direction bymeans of its springs.ATEX version in conformity with directive 2014/34/EU. Please add YX atthe end of the code for ATEX version.

Working Condition:Temperature: from 0°C to +80°C; from -20°C to +80°C with dry air only.(Special versions: hight temperature:-20°C +150°C; low temperature: -50°C +60°)Air supply: 5,6 bar; maximum 8,4 bar.Operating media: compressed filtered air, not necessarily lubricated.In case of lubricated air, either non detergent oil or NBR compatible oil,must be used.

Brand Omal

Omal Aluminium Double Acting (DA)Pneumatic Actuator

Description

Technical Features:Torque from 8 Nm to 8000 Nm.Mounting flange according to EN ISO 5211F03 - F04 - F05 - F07 - F10 - F12 - F14 - F16 - F25.In accordance with EN 15714-3Rotation angle 90°Torque: directly proportional to the air supply (see table).The code numbers after the DA letters, always correspond to thebreakaway torque in Nm by 5,6 bar air supply.ATEX version in conformity with directive 2014/34/EU. Please add YX atthe end of the code for ATEX version.

Working Condition:Temperature: from 0°C to +80°C; from -20°C to +80°C with dry air only.(Special versions: hight temperature:-20°C +150°C; low temperature: -50°C +60°)Air supply: 5,6 bar; maximum 8,4 bar.Operating media: compressed filtered air, not necessarily lubricated.In case of lubricated air, either non detergent oil or NBR compatible oil,must be used.

8 of 43

Brand Omal

Omal Butterfly Valves

Description

OMAL butterfly valves, available in wafer or lug version from DN 40 to DN600 (lug DN 300), are designed and manufactured to be used in mostapplications in all industrial fields.

General requirements in accordance with UNI EN593 Face to face as per EN 558 series 20Tightness at 16 bar according to EN 12266-1 rate AIntegral sealing (with liner vulcanized on hard ring) which avoids anycontact between fluid and valve body.Sealing design allowing perfect adherence to the valve body and perfecttightness to the flanges, without additional parts. Clamping betweenflanges does not influence the torque of the valve.Improved disc shape which allows better tightness, reduced torque andlow wear of the linerPTFE bushes to support the shaftCoupling between stem and disc with two shafts (better Kv) carried outwith no additional fittings (e.g. screws, bolts, pins, etc.) to avoid any risk ofcorrosion and breakingValve neck with top work as per EN ISO 5211 for easy connections withall different types of actuatorsAll components properly treated against corrosion

Brand Flomec

Flomec Turbo Pulse Turbine Flowmeter

Description

FLOMEC® Turbopulse Turbine Flowmeters measure flows of lowviscosity liquids from 3 to 7000 litres/hr in a range of sizes from ½“ to 20”(12-500mm). TP series flowmeters have an axial rotor and flow guides &need to be installed in straight sections of pipe either horizontal or verticalso that the flow is conditioned. TP series flowmeters can be purchasedwith Intrinsically Safe (I.S) approvals for use in hazardous areas.

Applications include the distribution of fuels, alcohols, solvents, meteringof chemicals, insecticides, water & light hydraulic oils.

Features / Benefits:

High accuracy & repeatability, direct reading flowmeterLow cost of ownership, wide flow rangeRugged & compact designCertified I.S hazardous area versionsIntegral 4-20mA output option

Integral Instruments:FLOMEC® TP series meter options include integral LCD totalisers, flowrate totalisers & batch controllers. These instruments provide monitoring &control outputs including 4~20mA, scaled pulse, alarms & batch control:

BT LCD 5 digit reset, 8 digit cumulative totaliser. RT12 LCD 6 digit reset, cumulative totaliser & flow rate. Analogue andpulse outputsRT40 LCD 6 digit reset, cumulative totaliser & flow rate. Backlit Display.EB LCD 6 digit 2 stage batcher & cumulative totaliser.

9 of 43

Brand Flomec

Flomec TM Series Water Meters

Description

FLOMEC® TM Series Water Meters are accurate, economical anddesigned to last. Choose TM Water Meters for water processing andirrigation applications:

Meets Schedule 80 PVC specificationsStandard low-profile displaySeven sizes with three fitting types available –1/2 inch, 3/4 inch, 1 inch, 1-1/2 inch, 2 inch. 3 inch & 4 inch;Spigot (Pipe) End, NPT or BSPP Female (1 inch thru 4 inch only) and150# ANSI Flange (3 and 4 inch only)Flowrates from 1 to 800 gallons per minute

Features / Benefits

Easy to install.Displays in gallons, litres and cubic feet.Indicates Batch, Cumulative Totals and Rate of Flow.Non-volatile totals means amounts are retained when batteries arereplaced or power is lost.Lithium battery life: 5 years

Brand Flomec

Flomec Insertion Flowmeter DP490

Description

DP490 and DP525 are cost effective stainless steel flow meters formeasuring the flow of water, fuels and other low viscosity liquids in pipesizes 1.5"~100" (40~2500mm).

Insertion flow meters are installed with the metering head 1/8th into thepipe resulting in very little pressure drop. They do not require externalpower when used with the Flomec rate totalisers, however some optionssuch as high temperature and non-magnetic models require externalpower.

Applications include HVAC, hot and chilled water, fire systems, waterdistribution (management and treatment), boiler feed water and hydrantflow testing.

Features:

IP68 (NEMA6) submersible 316SS construction Low cost of ownership, wide flow rangeRugged and compact designIntrinsically safe hazardous area versionsIntegral or remote pre-amplifiers and flow instrumentsDP525 version suitable for "hot tap" installationQuadrature pulse output option and Bi-Directional Flow MeasurementIntegral 4-20mA output option

Brand Flomec

Flomec Large Capacity Flowmeter

Description

Common transfer applications involve fuels, oils, solvents, alcohols alongwith the blending of bio and ethanol fuels either pumped or gravity fed.The meters are compact and light weight in construction, importantbenefits when used in mobile installations or within confined spaces.

10 of 43

Features and Benefits:

High accuracy and repeatability, direct reading flowmeterNo requirement for flow conditioning (straight pipe runs)Various rotor material optionsMeasures high and low viscosity liquidsQuadrature pulse output option and bi-directional flowIntegral 4-20mA output optionOptional Exd I/IIB approval (ATEX, IECEx)

Brand Flomec

Flomec Medium Capacity Flowmeter

Description

Applications include the distribution of fuels, fuel oils, lubricants, alcohols,solvents, blending of bio and ethanol fuels, metering of chemicals, grease,adhesives, ink, insecticides and non-conductive liquids either pumped orgravity fed.

Features and Benefits:

High accuracy and repeatability, direct reading flowmeterNo requirement for flow conditioning (straight pipe runs)Various rotor material optionsMeasures high and low viscosity liquidsQuadrature pulse output option and bi-directional flowIntegral 4-20mA output optionOptional Exd I/IIB approval (ATEX, IECEx)

Integral Instruments

Flomec meter options include integral LCD totalisers, flow rate totalisersand batch controllers.

These instruments provide monitoring and control outputs including4~20mA, scaled pulse, alarms and batch control and are alsoavailable with robust mechanical registers:

FBT LCD 5 digit reset, 8 digit cumulative totaliserFRT12 LCD 6 digit reset, cumulative totaliser and flow rate - Analogueand pulse outputsFRT40 LCD 6 digit reset, cumulative totaliser and flow rate - BacklitdisplayFEB LCD 6 digit 2 stage batcher and cumulative totaliserFM / V* = Mechanical registers (see model numbering)

Brand Flomec

QSE Mag Flowmeter

Description

A dependable highly accurate electromagnetic flowmeter designed forflow and usage monitoring in a wide variety of applications including:HVAC, Turf/ Irrigation and other water reclamation applications.

FEATURES | BENEFITS

NSF-61 CertificationLow investment and operating costs± 0.5% accuracy of reading (from 0.25fps to 15 fps)Wide turndown ratio of 60:1Non-intrusive, with no moving parts to wear out, virtually maintenance freeand tolerates high flows without damageThe slightly modified bore permits unobstructed flow, and minimizes flowdisturbances and straight pipe requirements

11 of 43

7 lines sizes (1/2" to 4"): 1/2", 3/4", 1-1/2", 2", 3" & 4"Housing ported with "Thermal Well Supports" for sensors (EnergyManagement)Compatible with FLOMEC® 09 Electronics Display or FLOMEC QSI I/OBoard

Brand Flomec

RT40 Flow Rate Totaliser

Description

FLOMEC® LCD display RT40 battery powered flow rate totaliser isspecifically designed for computing & displaying flow rates & totals fromflow meters with pulse, sine wave or frequency outputs.

The instrument displays resettable (batch) total, cumulative total andinstantaneous flow rate in engineering units as programmed by the user.

ROBUST FIELD & PANEL ENCLOSUREDesigned for the more rugged applications in mines sites & mobileinstallations, the RT40 LCD display has a backlight panel & large digits fordistance viewing at night.

FEATURES

Battery or external powered, 6 digit large LCD total & 8 digit cumulativetotaliser, 5 digit rate displayRobust IP66/67~NEMA 4X Aluminium field & panel mountable housingLCD Backlighting standardScalable universal pulse or frequency inputsScaled pulse output PIN protected programmingSimple flow chart touch key programmingReverse polarity protectionLong battery lifeHeavy duty facia protector shieldRelay board with SPDT outputsFlowmeter & pipe mount kits

Brand Flomec

RT12 Flow Rate Totaliser

Description

FLOMEC® LCD display RT12 is a fully programmable self-powered flowrate totaliser specifically designed for computing & displaying flow rates &totals from flow meters with pulse, sine wave or frequency outputs.

The instrument displays resettable (batch) total, cumulative total andinstantaneous flow rate in engineering units as programmed by the user.

FEATURESSelf or external powered, 8 digit LCD total & 8 digit cumulative totaliser, 5digit rate displayRobust IP66/67~NEMA 4X universal mount or DIN Panel mount versionAluminium/GRN field & panel mountable housingScaled pulse, 4-20mA (Loop Powered) Output, Dual flow inputs (A+B, A-B, A÷B), multi point linearization of flow input or frequency inputsHigh & low flow alarms & Low Frequency cutoffPIN protected programmingSimple flow chart touch key programmingReverse polarity protectionNon volatile memory, Long battery lifeRelay board with SPDT outputs (Optional)Optional Intrinsically safe version to Exia IIB T4 version (IECEx & ATEX

12 of 43

approved)

Brand Flomec

RT14 Flow Rate Totalizer

Description

FLOMEC® OM-Series Mechanical FlowmetersLCD display RT14 is a fully programmable self-powered flow rate totaliserspecifically designed for computing & displaying flow rates & totals fromflow meters with pulse, sine wave or frequency out-puts. The instrumentdisplays resettable (batch) total, accumulated total and instantaneous flowrates in engineering units as programmed by the user. Flow meter inputs:suitable use with most pulse/frequency output meters such as reedswitch, coil, voltage pulse (Wiegand), NPN and PNP.

CONTROL OUTPUTSAn unscaled pulse output serves as an i nput signal amplifier ideally suitedfor coil type inputs from turbine or paddle wheel meters. The output can betransmitted over and can be configured for NPN/PNP with wiringconnection.

FEATURES / BENEFITS• Self or external powered, 8 digit LCD total, accumulated total and rate• Robust IP66/67-NEMA4X universal mount glass reinforced nylonenclosure with rubberized buttons and polycarbonate lens• GRN field & panel mountable housing• Sealed pulse, 4-20mA (Loop Powered) output, multi point linearization offlow input or frequency inputs• Flow alarm for high, low or high/low• PIN protected programming• Simple flow chart touch key programming• Non volatile memory, Long battery life• Flowmeter & pipe mount kits available• Reverse polarity protection• Non volatile memory, Long battery life• Flowmeter & pipe mount kits available

13 of 43

Brand Flomec

F130 Batch Controller

Description

The batch controller model F130 is a microprocessor driven instrumentdesigned for batching and filling of small batch sizes up to large quantitiesas well as displaying total and accumulated total.

INTEGRAL OPTIONS• OM Series• Ultra High Pressure Meters

Brand Flomec

EB10 Batch Controllers

Description

The EB10 is a high speed batch controller is specifically designed to beeither mounted direct to a meter, field mounted or in a panel and be usedin either single or dual stage batching processes. The EB10 is able tooperate on either extra low DC voltage or low low AC voltage.

INTEGRAL OPTIONS• OM Series• TP Turbine Meters• UM Utility Meters• Ultra High Pressure Meters

14 of 43

Brand Flomec

Explosion Proof Totalizers E018

Description

The E018 features an explosion proof microprocessor that is capable of15-point linearization table, a scaled pulse output and high and lowflowrate alarms. Furthermore the unit isHART-enabled and is analogue output (4-20mA capable. The E018 isdesigned for hazardous areas and harsh conditions and is available witheither metric or imperial connections. The housing is also available withbeing either. Stainless Steel or Aluminum bodies (Stainless Steel shownhere).

INTEGRAL OPTIONS• Selected OM Series• Ultra High Pressure Meters

Brand TRIMEC

Multipulse Medium Capacity PositiveDisplacement Flowmeters

Description

The Multipulse range of positive displacementflowmeters offer a high level of accuracy andrepeatability. These precision meters are used forflow rate measurement in flow monitoring andcontrol applications and for totalising in dispensingand batching. Multipulse meters are suitable for usewith a wide range of clean liquids including viscouslubricants, chemicals, food bases and non-conductive low viscositysolvents either pumped or gravity fed.

Features / Benefits• Flows: 0.2~330 litres/min ( 0.05~90 US gal/min )• Sizes: 15, 20, 25, 40 & 50mm ( 1/2”, 3/8”, 1”, 11/2”& 2”) connections• High accuracy & repeatability, direct reading flowmeter• No requirement for flow conditioning ( straight pipe runs etc. )• Intrinsically safe & explosion proof models available• Quadrature pulse output option & bi-directional flow

Calibration – PD FlowmetersAll Trimec Flow Products positive displacement (PD) flowmetersare flow tested and each is supplied with an individual calibrationcertificate. Calibration is traceable to the National MeasurementsInstitute (NMI) Australia.PD flowmeters, due to their application on a wide range of liquidviscosities, are calibrated at one point, multipoint calibration forPD meters is available on request at an additional charge.

15 of 43

Brand Sure InstrumentPower Supply 85-265Vac (Optional: 18-36 Vdc)Power Consumption 1OWAccuracy ± 0.5% accuracy of rate from 0.5-10 m/s- ± 1.0% accuracy of rate from 0.1-0.5 m/sRepeatability: 0.2%Minimum Fluid Conductivity: 5.0 micromhos/cmFlow Direction

Unidirectional or bidirectional, 2 separate totalizers(programmable)

Analog Outputs 4-20mA, 5OOohms Max LoadOutput Frequency

Scaled Pulse output, (open collector) Max 5KhzNoise Damping ProgrammablePulse Width Programmable up to 5OOmsZero-point Stability Automatic correctionAmbient Temperature -4 to 140º F (-20 to 60º C)Electrode Materials :Standard 316 Stainless SteelOptional Conduct FactoryLiner Material PTFE, FEP (Rubber)Fluid Temperature :PTFE 100ºC Standard (Customized: 180ºC)Rubber 60ºCPressure Limits 1.0 Mpa; Optional1.6; 2.5; 4.0 MpaCoil Power Pulsed DCPipe Spool Material 316 Stainless SteelMeter Housing Material Carbon Steel weldedFlanges :

LDG Series Electromagnetic Flowmeter -

Description

SURE corporation offers a broad selection of electromagnetic (Mag) flowmeters for industrial, water, and waste water flow measurementapplications worldwide. The units are offered in a wide variety of sizes andflow ranges for many industrial as well as OEM service.

Features and benefits

No moving parts; Virtually no pressure drop; Minimal maintenanceWide range of nominal diameters;Broad selection of lining and electrode materials

Applications

Agricultural; Food & Beverage; Chemical; Pulp & Paper; Water & WasteWater

Brand Sure InstrumentDiameter 15-250mmConnection flange;SanitaryType Compact;RemoteBody Material SS304;SS316Power Supply 24VDC; BatterySignal Output 4-020mA/PulseCommunication HartAccuracy 1.5%;1.0%Application Liquid;Gas

Rotameter

16 of 43

Brand Sure InstrumentModel Code LDGS- 0050SM1F - 012Explanation - Diameter 150mmTransmitter CompactElectrode Material SS316LSignal Output 4 -20mA/PulseLiner Material PTFEPower Supply 110 - 240VacCommunication RS485; Grounding ELECTRODE

Sanitary Magnetic Flow Meter - LDGSSeries

Description

The sanitary magnetic flow meter Is specifically designed formeasurement of food llquidslike milk, cream, juices of various fruits, pharma liquids etc. lt is availablewith compactor remote version of transmitter can be installed either horizontally orvertically with a variety of optional end-fittings to meet your need.

note: Please read the nameplate or calibration certificate forspecifications.

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug VITONPiston Stainless SteelPiston plug PTFEValve body Stainless Steel

SUS-80FNO

Description

PRODUCT DESCRIPTION• SUS-FNO series is multiplex, piston guiding, conductive and normallyclosed (NC)2/2 way solenoid valve.• Applied fluid type : water, air, light oilCAUTIONS:• Minimum pressure to open: over 1kgf-cm'• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-type filter at the front end of solenoid valve.• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

17 of 43

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug VITONPiston Spring Stainless SteelPiston Stainless SteelPiston plug PTFEValve body Stainless Steel

SUS-15NO~50NO

Description

PRODUCT DESCRIPTION

• SUS-NO series is multiplex, piston guiding, conductive and normallyclosed(NC) 2/2 way solenoid valve.• Recommend to apply to frequent operation• Applied fluid type : water, air, steam, light oil• Acceptable for customize Viton, Silicone and EPDM for seal plug anddiaphragmCAUTIONS:• Minimum pressure to open: over 0.5kgf-cm'• Before pipelining, the pipe line must be very clean without anycontaminants orimpurity.• To extend the lifetime, Y-type filter at the front end of solenoid valve.• AC voltage tolerance:± 10%; DC voltage tolerance:± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20 est

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug VITONO-ring NBRValve body Stainless Steel

SUS-6NO~10NO

Description

PRODUCT DESCRIPTION

• SUS series is direct-acting, conductive, and normally closed (NC) 2/2way solenoid valve.• Able to operate under no differential pressure• Applied fluid type : water, air, steam, light fuel, gas, vacuum• Acceptable for customize Viton (130"C), Silicone (130"() and EPDM(130"()for seal plug and diaphragmCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants orimpurity.• To extend the lifetime, Y-type filter at the front end of solenoid valve.• The temperature of steam should not over 185"(• AC voltage tolerance:± 10%; DC voltage tolerance:± 1%

18 of 43

• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over SOcst

Brand mit-UNID-cnsMATERIAL MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug VITONPiston Spring Stainless SteelPiston BrassPiston plug PTFEValve body Forged Brass

UPS-15NO~25NO

Description

PRODUCT DESCRIPTION• UPS-NO series is multiplex, piston guiding, conductive and normallyclosed (NC)2/2 way solenoid valve.• Recommend to apply to frequent operation• Applied fluid type : water, air, steam, light oil• Acceptable for customize Viton, Silicone and EPDM for seal plug anddiaphragmCAUTIONS:• Minimum pressure to open: over 0.5kgf-cm'• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-type filter at the front end of solenoid valve.• AC voltage tolerance:± 10%; DC voltage tolerance:± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20 est

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug NBRDiaphragm NBRValve body Forged Brass

UW-10NO~50NO

Description

PRODUCT DESCRIPTION• UW-NO series is direct, multiplex, connected diaphragm, conductive andnormally closed(NC) 2/2 way solenoid valve.• Able to operated directly under low pressure• Applied fluid type : water, air, light oil• Acceptable for customize Viton (130°(), Silicone (130°() and EPDM(130°() for sealplug and diaphragmCAUTIONS:

19 of 43

• Before pipelining, the pipe line must be very clean without anycontaminantsor impurity.• To extend the lifetime, Y-type filter at the front end of solenoid valve.• AC voltage tolerance:± 10%; DC voltage tolerance:± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug NBR(Viton, Silicone, PTFE)O-ring NBR (PTFE)Valve body Forged Brass

UD-6NO~10NO

Description

PRODUCT DESCRIPTION• UDNO series is direct-acting, conductive, and normally closed (NC) 2/2way solenoid valve.• Able to operate under no differential pressure• Applied fluid type :water, air, light fuel, gas, vacuum• Acceptable for customize Viton (130.(), Silicone (130°() and EPDM(130°()for seal plug and diaphragmCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants orimpurity.• To extend the lifetime, Y-type filter at the front end of solenoid valve.• AC voltage tolerance:± 10%; DC voltage tolerance:± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug PTFEPiston Spring Stainless SteelPiston plug PTFEValve body Cast Iron (FC-20)

US-35F~100F

Description

PRODUCT DESCRIPTION• SUW series is multiplex, piston guiding, conductive and normally closed(NC) 2/2 way solenoid valve.• Applied fluid type :water, air, light oil• Acceptable for customization Viton (130°() , Silicone (130°() and EPDM(130°() for seal plug

20 of 43

CAUTIONS:• Minimum pressure to open: over O.Skgf-cm2• Before pipelining, the pipe line must be very clean without anycontaminants orimpurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoidvalve.• AC voltage tolerance:± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug NBRDiaphragm NBRValve body Cast Iron (FC-20)

UW-35F~100F

Description

CAUTIONS:• Minimum pressure to open: over O.Skgf-cm'• Before pipelining, the pipe line must be very clean without anycontaminants orimpurity.• To extend the lifetime,Y-Iine filter should be installed in the front end ofsolenoidvalve.• AC voltage tolerance:± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug PTFEPiston Spring Stainless SteelPiston Stainless SteelPiston plug PTFEValve body Stainless Steel

SUS-80F

Description

PRODUCT DESCRIPTION• SUS-F series is multiplex, piston guiding, conductive and normallyclosed(NC) 2/2 way solenoid valve.• Applied fluid type :water, air, light oilCAUTIONS:

21 of 43

• Minimum pressure to open: over 1kgf-cm'• Before pipelining, the pipe line must be very clean without anycontaminants orimpurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoidvalve.• AC voltage tolerance:± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug NBRDiaphragm NBRValve body Stainless steel

SUW-80F

Description

PRODUCT DESCRIPTION• SUW-F series is multiplex, piston guiding, conductive and normallyclosed{NC} 2/2 way solenoid valve.• Applied fluid type :water, air, light oilCAUTIONS:• Minimum pressure to open: over O.Skgf-cm2• Before pipelining, the pipe line must be very clean without anycontaminants orimpurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoidvalve.• AC voltage tolerance:± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst


SUSF-15~50

Description

PRODUCT DESCRIPTION

22 of 43

• SUSF series is multiplex, piston guiding, conductive and normally closed

(NC) 2/2 way solenoid valve.• Applied fluid type : water, air, steam, light oil• Recommend to apply to frequent operation• Acceptable for customization Viton (130°() , Silicone (130°() and EPDM(130°()for seal plugCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants orimpurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst


SUS-15~50

Description

PRODUCT DESCRIPTION• SUS series is multiplex, piston guiding, conductive and normally closed(NC) 2/2 waysolenoid valve.• Applied fluid type : water, air, steam, light oil• Recommend to apply to frequent operationCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug NBRDiaphragm NBRValve body Stainless Steel

SUWF-15~50

23 of 43

Description

PRODUCT DESCRIPTION• SUWF series is direct, multiplex, connected diaphragm, conductive andnormallyclosed (NC) 2/2 way solenoid valve.• Able to operate under low pressure• Applied fluid type :water, air, light oil, gas, vacuum• Acceptable for customization Viton (130"C), Silicone (130"(} and EPDM(130"(}for seal plug and diaphragmCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants orimpurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug NBRDiaphragm NBRValve body Stainless Steel

SUW-15~50

Description

PRODUCT DESCRIPTION• SUW series is direct, multiplex, connected diaphragm, conductive andnormallyclosed (NC) 2/2 way solenoid valve.• Able to operate under low pressure• Applied fluid type :water, air, light oil, gas, vacuum• Acceptable for customization Viton (130"C), Silicone (130"() and EPDM(130"()for seal plug and diaphragmCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants orimpurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)

SUS-6~10

24 of 43

Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug PTFE(standard) NBRO-ring PTFE(standard) NBRValve body Stainless Steel

Description

PRODUCT DESCRIPTION

• SUS series is direct-acting, conductive, and normally closed (NC) 2/2way solenoid valve.• Able to operate under no differential pressure• Applied fluid type :water, air, steam, light oil, gas, vacuum• Acceptable for customization Viton (13o•q , Silicone (130°() and EPDM(13o•q for seal plug.CAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• The temperature of steam should not over 18s•c• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over SOcst

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelOring Synthetic rubberDiaphragm PTFEValve body PVC

UDC-8~25

Description

PRODUCT DESCRIPTION• UDC series is direct-acting, conductive and normally closed {NC) 2/2way solenoid valve.• Able to operate under no differential pressure• Applied fluid type : water, air• PVC valve body is corrosion-resistant {pH 3-11)CAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• No frequent operation• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Viscosity over 20 est

Brand mit-UNID-cnsPARTS MATERIAL

USF-15~50

25 of 43

Coil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug PTFE +15%GFPiston BrassPiston plug PTFEValve body Cast Bronze

Description

PRODUCT DESCRIPTION• USF series is multiplex, piston guiding, conductive and normally closed(NC}2/2 way solenoid valve.• Applied fluid type : water, air, steam, heavy oilCAUTIONS:• Minimum pressure to open: over O.S-1kgf-cm'• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20 est

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug PTFE +15%GFPiston BrassPiston plug PTFEValve body Cast Bronze

US-15~50

Description

PRODUCT DESCRIPTION

• US series is multiplex, piston guiding, conductive and normally closed(NC)2/2 way solenoid valve.• Applied fluid type : steam, heavy oilCAUTIONS:• Minimum pressure to open: over O.S-1kgf-cm'• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• AC voltage tolerance:± 10%; DC voltage tolerance:± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20 est

Brand mit-UNID-cns

UWF-10~50

26 of 43

PARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelPlug NBRDiaphragm NBRValve body Forged Brass

Description

PRODUCT DESCRIPTION• UWF series is direct, multiplex, connected diaphragm, conductive andnormally closed (NC)2/2 way solenoid valve.• Able to operate under low pressure• Applied fluid type : water, air, light oil• Acceptable for customization Viton (13o•q , Silicone (13o•q and EPDM(13o•q for sealplug and diaphragmCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst


UW-10~50

Description

PRODUCT DESCRIPTIONNPT: NPT• UW series is direct, multiplex, connected diaphragm, conductive andnormally closed (NC)2/2 way solenoid valve.• Able to operate under low pressure• Applied fluid type : water, air, light oil• Acceptable for customization Viton (130"C), Silicone (130"C) and EPDM(130"C) for sealplug and diaphragmCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

27 of 43

Brand mit-UNID-cnsPARTS MATERIALCoil Special copper wire (H class)Tube Stainless steelSpring Stainless steelCore Stainless steelPlug NBRDiaphragm NBRValve body Forged Brass

UV-10~50

Description

PRODUCT DESCRIPTION• UV series is direct, multiplex, connected diaphragm, conductive andnormally closed (NC)2/2 way solenoid valve.• Able to operate under no differential pressure• Applied fluid type : vacuumCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• AC voltage tolerance:± 10%; DC voltage tolerance:± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst


UG-10~50

Description

PRODUCT DESCRIPTION• UG series is direct, multiplex, connected diaphragm, conductive andnormally closed (NC)2/2 way solenoid valve.• Able to operate under no differential pressure• Applied fluid type : gasCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• AC voltage tolerance:± 10%; DC voltage tolerance:± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

28 of 43

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug PTFEPiston Spring Stainless SteelPiston BrassPiston plug PTFEValve body Cast Bronze

UPS-15~25

Description

PRODUCT DESCRIPTION• UPS series is multiplex, piston guiding, conductive and normally closed(NC) 2/2 way solenoid valve.• Recommend to apply to frequent operation• Applied fluid type : water, air, steam, light oil• Acceptable for customization Viton , Silicone and EPDM for seal plugCAUTIONS:• Minimum pressure to open: over 0.5kgf-cm'• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front endof solenoid valve.• AC voltage tolerance:± 10%; DC voltage tolerance:± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20 cst

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug PTFEPiston BrassPiston plug PTFEValve body Cast Bronze

USS-15

Description

PRODUCT DESCRIPTION• USS series is direct-acting, piston guiding, conductive, and normallyclosed (NC) 2/2 waysolenoid valve.• Recommend to apply to frequent operation• Applied fluid type : water, air, steam, light oilCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants or anyimpurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• The temperature of steam should not over 1ss•c• AC voltage tolerance:± 10%; DC voltage tolerance:± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.

29 of 43

• Corrosive fluid• Viscosity over 5Ocst

Brand mit-UNID-cnsPARTS MATERIALCoil Special copper wire (H class)Tube Stainless steelSpring Stainless steelCore Stainless steelPlug NBR (Viton, Silicone, PTFE)Piston BrassPiston plug NBRValve body Brass

UAO-8~15

Description

PRODUCT DESCRIPTION• UAO series is multiplex, piston guiding, conductive, and normally closed{NC} 2/2 waysolenoid valve.• Applied fluid type : water, air, heavy oil• Recommend to apply to frequent operation• Applied to sand blasting machine and high-pressure air and oil injectionsystem.CAUTIONS:• Minimum pressure to open: over O.Skgf-cm'• Before pipelining, the pipe line must be very clean without anycontaminants impurity.• To extend the lifetime, Y-line filter should be installed in the front endof solenoid valve.• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 5Ocst

Brand mit-UNID-cnsPARTS MATERIALCoil Special copper wire (H class)Tube Stainless steelSpring Stainless steelCore Stainless steelPlug PTFEO-ring PTFEValve body Forged Brass

US-6~10

Description

PRODUCT DESCRIPTION• US series is direct-acting, conductive, and normally closed (NC) 2/2 waysolenoid valve.• Able to operate under no differential pressure• Material PTFE is applied to steam.CAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• The temperature of steam should not over 1ss•c• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:

30 of 43

• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 5Ocst

Brand mit-UNID-cnsPARTS MATERIALCoil Special Copper Wire ( H class)Tube Stainless SteelSpring Stainless SteelCore Stainless SteelPlug NBR (Viton, Silicone, PTFE)O-ring NBR (PTFE)Valve body Forges Brass

UD-6~15

Description

PRODUCT DESCRIPTIONNPT: NPT• UD series is direct-acting, conductive, and normally closed (NC) 2/2 waysolenoid valve.• Able to operate under no differential pressure• Applied fluid type :water, air, light oil, gas, vacuum• Acceptable for customization: Viton (130'C) , Silicone (130'C) and EPDM(130'C) for seal plugCAUTIONS:• Before pipelining, the pipe line must be very clean without anycontaminants or impurity.• To extend the lifetime, Y-line filter should be installed in the front end ofsolenoid valve.• AC voltage tolerance: ± 10%; DC voltage tolerance: ± 1%• It should be installed horizontally; vertical installation is not advisable.Not Suitalbe For Fluid As Below:• Liquid status when it is in high temperature; solid status when it is in lowtemperature.• Corrosive fluid• Viscosity over 20cst

31 of 43

Brand mit-UNID-cnsModels UM-3-1Power 30WSpeed 90 sec (60Hz) 1-8Torque(5%} kgf-cm2 AC24V 500 / 1500No-loadcurrent consumption (AC24V) 0.3AFlange/Mounting Type( ISO 5211) F07Max Width (mm / inch) L=17.05 / L=0.67Max Depth (mm / inch) D=27 / D=1.06Weight (kg) 7.5Manual Override Device Hand Wheel

UM-3-1

Description

Product Specification

• DC24V Electric Actuator Product Specification• The following values are based on 60HZ as reference.The value varies slightly from the different frequency of the power supply.

* If the working pressure is more than 10kgf-cm2 , you should replace itwith a bigger one.

* If you need to install modulating series or the torque of valve is too tight,you should replace it with a bigger one.

Brand mit-UNID-cnsModels UM-3Power 30WSpeed 90 sec (60Hz) 1-8Torque(5%} kgf-cm2 AC24V 500 ~ 1500No-loadcurrent consumption (AC24V) O.5AFlange/Mounting Type( ISO 5211) F07Max Width (mm / inch) L=17.05 / L=0.67Max Depth (mm / inch) D=18 / D=0.71Weight (kg) 4.5Manual Override Device Wrench

UM-3

Description





32 of 43

Brand mit-UNID-cnsModels R-5~15Power 10W~20WSpeed 90 sec (60Hz) 20Torque(5%} kgf-cm2 AC24V 600No-loadcurrent consumption (AC24V) 0.1AFlange/Mounting Type( ISO 5211) F04 / F05 / F07Max Width (mm / inch) L=17.15 / L=0.68Max Depth (mm / inch) D=17 / D=0.67Weight (kg) 2.5Manual Override Device Wrench

R-5~15

Description





Brand mit-UNID-cnsModels UM2-5 / UM2-7Power 10WSpeed 90 sec (60Hz) 16Torque(5%} kgf-cm2 AC24V 700No-loadcurrent consumption (AC24V) 0.1AFlange/Mounting Type( ISO 5211) F03 / F05, F04, F05 / F07Max Width (mm / inch) L=14.03 / L=0.55Max Depth (mm / inch) D=17 / D=0.67Weight (kg) 1.6 / 1.8 kgManual Override Device Wrench

UM2-5~2-7

Description


• DC24V Electric Actuator Product Specification

• The following values are based on 60HZ as reference.

The value varies slightly from the different frequency of the power supply.


33 of 43


Brand mit-UNID-cnsModels UM-1Power 10WSpeed 90 sec (60Hz) 2.5Torque(5%} kgf-cm2 AC24V 250No-loadcurrent consumption (AC24V) O.lAFlange/Mounting Type( ISO 5211) F03 / F05, F04, F05 / F07Max Width (mm / inch) L=14.03 / L=0.55Max Depth (mm / inch) D=17 / D=0.67Weight (kg) 1.6, 1.8Manual Override Device Wrench

UM-1

Description





PNEUMATIC ROTARY ACTUATORS -AP·APM SERIES

Description

ATTUATORI A SEMPLICE EFFETTO (SR) ISO 5211

SPRING RETURN ACTUATORS (SR) ISO 5211

PRINCIPIO Dl FUNZIONAMENTO • PRINCIPLE OF OPERATION

Pressione di alimentazione

2 bar ( 29 psig ) a B bar ( 116 psig ) doppio effetto

3 bar ( 44 psig) a B bar ( 116 psig) semplice effetto

34 of 43

max. pressione di alimentazione 10 bar ( 145 psig ).

Alimentazione: aria secca o lubrificata, filtrata.Per gas non corrosive, acqua o olio idraulicoconsultare Ufficio Tecnico Sirca

Temperatura: STD -2oac (-4aF) a +Boac (175aF). . +20°C (+6BaF) a +150°C (302°F)a riChlesta - 50aC (-58aF) a +100°C (212aF).

Rotazione: antioraria quando l'alimentazione 9 in PORT 'A'oraria quando l'alimentazione l:! in PORT 'B' enegli attuatori con molle di ritorno (vedereprincipia di funzionamento).

Corsa: eoa con regolazione meccanica ± 3a (serie AP)o doppia regolazione ± 5a (serie APM)

Brand IWAItem ITS-300Enclosure IP67, Explosion-proof Ex dII BT6Electrical Interface PF 3/4”Terminals 10Position Indicator

0°-90° Rotary (Yellow – Open, Red – Close)Ambient Temperature -20°C~+70°CMounting Brackets

VDI/VDE 3845, Namur Standard, Stainless SteelMicro-switch SPDT, SPST

ITS-300 Limit Switch Box (Explosion ProofType) (MIT)

Brand IWAItem StandardEnclosure Weatherproof IP67/NEMA4 & 4XTemperature -20°C to 80°CConduit Entries 2 x M20Terminal Strips 8 points (.08-2.5mm²)Position Indicator Closed: Red, Open: YellowSwitches Mechanical switch x 2 SPDTExternal Coating Polyester powder coating (black)Shaft ISO Standard (17mm long)Housing Powder coated die cast aluminiumCam

Quick Set spring loaded splined cam (no need to adjustagain after initial setting, set without tools)

Mounting Interface Namur

ITS-100 Limit Switch Box

35 of 43

Max Current 10 AMP AC, 2 AMP DC

Description

Powder coated aluminum body. IP67 protection.Two M20 cable entry.High visability dome indicator.Two single pole double throw voltage freeswitches.Max current 10 AMP AC, 2 AMP DC

Brand I-TORK

ITQ 0080 Series

Description

Newly Designed and developed for especially small ball & plug valves anddamper automation.Self-Locking combination of spur and worm gears that require no brake.The motor is a specially designed induction motor that produces highstarting torques and thermally protected from overheating.Mechanical Stopper bolts to prevent from over travel.Easy set cams without special toolManual operation by wrench directly to the worm gear box and dialpostion indication

Brand I-TORK

ITQ 0040 Series

Description

Suitable for on-off small ball/plug vavles and damper automationBy combination of spur gears, provide vvery high efficiencyThe motor is a specially designed induction motor that produces highstarting torques and thermally protected from overheating.Manual Operation by Spanner and dial position indicationVery compact and light weight & High Duty Cycle

36 of 43

Brand I-TORK

ITS 100 Series

Description

Whetherproof ITS series position monitoring switch boxes are primaryrotary position indication device designed to integrate valve and NAMURrotary pneumatic actuator with a variety of mounting options, internalswitches or sensors and configulations.Rigid and compact design constructed from aluminum alloy die-castingcapable of operating even in arduous conditions. Dome position indicator constructed from high resistance poly-carbonatematerial which offers instant visual recognition of valve or actuatorposition up to 50 meters distance.

Brand PowerGenex

SS3 Smart Positioner

Description

Smart performance with flameproof enclosure and innovative and ever-strong coil module even under harsh working environments.

Features:- Easy and quick auto-calibration - Detecting RA (reverse acting) or DA (direct acting) automatically regardless of wrong air connections- Available to use for single or double acting without any specialadjustments - Compact design allowing to be installed on small actuators- Providing error messages against performance failures- Possible to test the actuator with any fixed signal under a test mode- Programmable characteristic curve with 17 points- Wide operating temperature range -30 ~ +75℃- Improved control of high-friction globe and ball valves by eliminating an overshoot and a hunting- Low air consumption- Providing a mounting bracket to meet IEC 60534-6-1 for linear valves- Supporting a NAMUR mounting pattern VDI/VDE 3845 (IEC 60534-6-2)and providing a multi-size mounting bracket for rotary valves

Option:- Output position transmitter (4 - 20 mA)- 2 x alarm limit or micro switch (SPDT)- By-pass (Auto-manual screw)- HART communication- Profibus PA communication - Fieldbus FF communication

Brand PowerGenex

EPR (Rotary Type)

Description

Robust valve control device giving a confidence in reliable performanceand outstanding durability under harsh working environments.

Features:- Easy maintenance- Precise calibration with simple SPAN and ZERO adjustments- Simple conversion to direct acting or reverse acting

37 of 43

- 1/2 split range available- Rugged aluminum housing with corrosion-resistant coating- Vibration resistant design- Stainless steel gauges standard- Restricted pilot valve orifice kit for small actuators included- Certified for ATEX Eex md IIB T5 (05 ATEX 1076X) by NEMKO inconformance with EN 50014:1997, EN 50018:2000 and EN 50028:1987- Certified for EMC (K1046/E04) in conformance with EN 61000-6-2:2001and EN 61000-6-4:2001 by RWTUV- Certified for Ex md IIB T6 (99-1075-Q1), Ex md IIC T6 (2000-1057-Q1),and Ex ia IIB T6 (2000-1056-Q1) by KOSHA

Brand PowerGenex

EPL (Linear Type)

Description

Robust valve control device giving a confidence in reliable performanceand outstanding durability under harsh working environments.

Features:- Easy maintenance- Precise calibration with simple SPAN and ZERO adjustments- Simple conversion to direct acting or reverse acting- 1/2 split range available- Rugged aluminum housing with corrosion-resistant coating- Vibration resistant design- Stainless steel gauges standard- Restricted pilot valve orifice kit for small actuators included- Certified for EMC (K1046/E04) in conformance with EN 61000-6-2:2001and EN 61000-6-4:2001 by RWTUV

Brand Eurotec

NAMUR Solenoid Valves Aluminum MNI52

Brand Eurotec

NAMUR Solenoid Valves AluminumMNF532

38 of 43

Brand Eurotec

Housing EPP IP67

Description

For More Details:https://www.eurotec1996.com/english/products/3-wave-standard/

Brand Eurotec

i-box Housing IP66/IP67

Description

For More Details:http://files.eurotec-shop.com/S02_i-box_IP.pdf

39 of 43

https://www.eurotec1996.com/english/products/3-wave-standard/

http://files.eurotec-shop.com/S02_i-box_IP.pdf

Brand italvalvole

Pneumatic Control Valve

Description

For More Details:https://www.italvalvole.com/en/pages/control-valves-36.html

Brand FIP

VM/CP DN 80÷100 PNEUMATICALLYACTUATED DIAPHRAGM VALVE

Description

The VM is particularly suitable for shutting off and regulating abrasive ordirty fluids. The handwheel control and diaphragm seal provide preciseand effective control, while reducing the risk of water hammer to aminimum.

In addition to manually operated version, the VM is also available inconfiguration with pneumatical actuator VM/CP.

VM/CP are produced using actuators complying with current regulationsand selected by FIP according to its requirements of quality and reliability.

MAIN FEATURES:

Connection system for solvent weld, threaded and flanged jointsCompact and lightweight constructionHigh flow coefficient and minimum pressure dropInternal components in metal totally isolated from the conveyed fluid, withanti-friction disk to reduce friction to a minimumModularity of the range: only 5 diaphragm and bonnet sizes for 9 differentvalve sizesHandwheel that stays at the same height during rotationBonnet fastening screws that screw into the built-in bush preventing thedeposit of dirt or impuritiesCDSA system (Circular Diaphragm Sealing Angle) used up to DN50,offering the following advantages:uniform distribution of shutter pressure on the diaphragmreduction in the tightening torque of the screws fixing the actuator to thevalve bodyreduced mechanical stress on all valve components (actuator, body anddiaphragm)easy to clean valve interiorlow risk of the accumulation of deposits, contamination or damage to thediaphragm due to crystallisationoperating torque reduction

For More Details:http://www.fipnet.com/prodotti/vmcp-dn-80%C3%B7100/?lang=en

40 of 43

https://www.italvalvole.com/en/pages/control-valves-36.html

http://www.fipnet.com/prodotti/vmcp-dn-80%C3%B7100/?lang=en

Brand FIP

TKD/CE - TKD/CP DN 10÷50ELECTRICALLY AND PNEUMATICALLYACTUATED DUAL BLOCK® 3-WAY BALLVALVE

Description

FIP has developed a TKD DUAL BLOCK® ball valve to introduce a highreference standard in thermosplastic valve design. TKD is a True Uniondiverting and mixing ball valve that meets the most stringent needsrequired in industrial applications.

In addition to manually operated version, the TKD is also available inconfiguration with electrical actuator TKD/CE or pneumatical actuatorTKD/CP.The actuators are firmly connected to the valve with a special modulePower Quick made by FIP entirely produced in technopolymer PP-GR.

The TKD/CE and TKD/CP are produced using actuators complying withcurrent regulations and selected by FIP according to its requirements ofquality and reliability. The efficiency of these valves, tested according tothe company quality standards, is guaranteed by the expertise and know-how that FIP dedicates to the manufacture of its products.

MAIN FEATURES:

Connection system for solvent weld, threaded and flanged jointsPatented SEAT STOP® ball carrier system that lets you micro-adjust ballseats and minimise axial force effectsEasy radial dismounting allowing quick replacement of O-rings and ballseats without any need for toolsPN16 True Union valve body made for rigid PVC-U injection mouldingequipped with built-in bores for actuation. ISO 9393 compliant testrequisitesOption of dismounting downstream pipes with the valve in the closedpositionHigh surface finish stem with double O-Ring and double connection key tothe ballIntegrated bracket for valve anchoringPneumatic or electric actuators installed on the robust anchor towerthrough the Power Quick module

For More Details:http://www.fipnet.com/prodotti/tkdce-tkdcp-dn-10%C3%B750/?lang=en

Brand FIP

FE DN 40÷200 BUTTERFLY VALVE

Description

The FE is a butterfly valve for shutting off or regulating flow, specificallydesigned for water applications and equipped with a customisableLabelling System.

Disk in PVC-U with through shaft Zinc plated square section steel stem completely isolated from thefluid complying with standard ISO 5211:

DN 40 ÷ 65: 11 mmDN 80 ÷ 100: 14 mm DN 125 ÷ 150: 17 mmDN 200: 22 mm

Can also be installed as an end line valve, bottom discharge valve or tankdump valveThe wafer valve can be transformed into a one-way Lug body valvethanks to the set of zinc plated steel inserts available as an optional extra

41 of 43

http://www.fipnet.com/prodotti/tkdce-tkdcp-dn-10%C3%B750/?lang=en

Valve material compatibility (PVC-U) with water conveyance, drinkingwater and other food substances according to current regulations.Possibility of directly installing a gearbox or pneumatic and/or electricactuators with a standard drilling pattern according to standard ISO 5211F05, F07, F10

MAIN FEATURES:

Ergonomic multifunctional handle in HIPVC with the option for quickoperation, graduated adjustment in 12 positions (every 7.5°). 180°reversible mounting Customisable Labelling System: integrated module, made of atransparent protection plug customisable tag holder using the LSE set(available as accessory). The customisation lets you identify the valve onthe system according to the specific needsDrilling pattern with oval slots that allow coupling to flanges accordingto numerous international standardsInterchangeable liner with the dual function of forming a hydraulic sealand isolating the body from the fluid.One-piece top flange with PVC-U rack. Drilling according to standardISO 5211 for direct drive:

DN 40 ÷ 65: F05DN 80 ÷ 150: F07DN 200: F10

For More Details:http://www.fipnet.com/prodotti/fe-dn-40%C3%B7200-2/?lang=en

Brand FIP

VKD DN 10÷50 DUAL BLOCK® 2-WAYBALL VALVE

Description

FIP has developed a VKD DUAL BLOCK® ball valve to introduce a highreference standard in thermosplastic valve design.

VKD is a True Union ball valve that meets the most stringent needsrequired by industrial applications.

• Connection system for solvent weld, threaded and flanged joints• Patented SEAT STOP® ball carrier system that lets you micro-adjust ballseats and minimise the axial force effect.• Easy radial dismounting allowing quick replacement of O-rings and ballseats without any need for tools• PN16 True Union valve body made for rigid PVC-U injection mouldingequipped with built-in bores for actuation. ISO 9393 compliant testrequisites• Option of dismounting downstream pipes with the valve in the closedposition• Floating full bore ball with high surface finish• Integrated bracket for valve anchoring• Ball seat carriers can be adjusted using the Easytorque adjustment kit

MAIN FEATURES:

Ergonomic HIPVC handle equipped with removable tool to adjust the ballseat carrier.Handle lock 0°- 90° SHKD (available as an accessory) ergonomicallyoperable during service and padlockableRobust integrated bracket for valve anchoring, for easy and quickautomation even after valve installation on the system via the PowerQuick module (optional)DUAL BLOCK® patented lock system that ensures union nut tighteninghold even in severe conditions such as vibrations or heat dilation

For More Details:http://www.fipnet.com/prodotti/valvola-a-sfera-a-2-vie-dual-block/?lang=en&lang=en

42 of 43

http://www.fipnet.com/prodotti/fe-dn-40%C3%B7200-2/?lang=en

http://www.fipnet.com/prodotti/valvola-a-sfera-a-2-vie-dual-block/?lang=en&lang=en

Tel 03-8060 5700Tel 012-399 3230Fax 03-8060 5900E-Mail [email protected] [email protected] www.pascalcontrol.com


No. 9, Jalan Intan 2/7, Taman Puchong Intan, 47150, Puchong, Selangor,Malaysia


43 of 43

Documents

Omal Thor Split Body Carbon Steel PN 16- Pascal Control ... · API 6D 2 of 53. Materials and rating in compliance with ASME B16.34 for ANSI valves and EN 12516 for PN valves Brand