Upload
phungthu
View
215
Download
0
Embed Size (px)
Citation preview
Anvil International is building the most advanced
Grooved Piping Resource in the industry. We seek to set
a new standard in Product Performance, Customer
Service, and Technical Support. Our Value Proposition is
clear. The Gruvlok team will meet and surpass Industry
Requirements in Manufacturing, Distribution, and Service
in Support of Every Customer – Every Time.
3
ANSI American National Standards InstituteAWWA American Water Works Association:C-606API American Petroleum Institute: API Std.5L, Sect.7.5ASHRAE American Society of Heating, Refrigerating and Air Conditioning EngineersASME American Society of Mechanical Engineers:
Power Piping, B-31.1;Chemical Plant and Petroleum Refinery Piping,B-31.3;Refrigeration Piping, B-31.5; Building Services Piping, B-31.9;Slurry Pipelines, B-31.11
ASTM American Society of Testing and Materials:F-1476, F-1387BBA British Board of AgrementCDF California State Fire MarshalCSA Canadian Standards Association:B-242FM Factory Mutual Engineering Corp. IAPMO International Association of Plumbing &Mechanical OfficialsLLOYD ’S Lloyd ’s Register of ShippingMEA Materials &Equipment AcceptanceNFPA National Fire Protection AssociationNY-BSA New York Board of Standards and AppealsNSF NSF InternationalSBCCI Southern Building Code Congress International:
Standard Plumbing and Mechanical CodeUL Underwriter ’s Laboratories, Inc. ULC Underwriter ’s Laboratories of Canada
Bureau of Marine Inspection:Salt and fresh water, oil transferBureau of Public Roads;Div. of Bridges:Drain lines and bridge crossings
Canadian Coast GuardU. S. Coast Guard – Approves each vessel individuallyABS American Bureau of Shipping
COE Corps of Engineers: CEGS 15000FAA Federal Aviation Administration:
HVAC, Plumbing, Fire ProtectionFHA Federal Housing AdministrationGSA General Services Administration:15000 SeriesMIL Military Specifications:
MILP-10388 Fittings;MIL-C-10387 Couplings; MIL-P-11087A(CE)Steel Pipe,Grooved MIL-I-45208 Inspection Procedure
NASA National Aeronautics and Space Administration:15000 SeriesNAVFAC Naval Facilities Engineering Command:NFGS 15000 SeriesNIH National Institute of Health (Dept. of Health):15000 SeriesTVA Tennessee Valley Authority:Fire protection, storm drainsVA Veterans Affairs :15000 Series
WorldwideBV Bureau VeritasDNV Det Norske VeritasHong Kong Fire Services BoardNew Zealand Insurance CouncilNew Zealand Building Act. (1991)SSL Scientific Services LaboratoryStandards AustraliaVdS Verband der Sachversicherer e. V.LPC Loss Prevention CouncilWRC Water Research CouncilDVGW Deutscher Vereindes Gas und Wasserfaches e. V. BBA SM Board of Agremont
INDUSTRY AND GOVERNMENT STANDARDS & APPROVALS
TABLE OF CONTENTSGruvlok® Valves
Series 7500 Ball Valves . . . . . . . .4Grooved End Diverter Valves . . . .4Series 7700 . . . . . . . . . . . . . . . . . .4
Swages, Bull Plugs, Tubing & CasingNipples
Bull Plugs . . . . . . . . . . . . . . . . . . . .5Line Pipe Swages . . . . . . . . . . . . .5Oil Country Swages . . . . . . . . . . . .5Tubing Nipples . . . . . . . . . . . . . . . .5Casing Nipples . . . . . . . . . . . . . . . .5
Catawissa® Wing UnionsFig. 100 . . . . . . . . . . . . . . . . . . . . . .6Fig. 200 . . . . . . . . . . . . . . . . . . . . . .6Fig. 202 . . . . . . . . . . . . . . . . . . . . . .6Fig. 206 . . . . . . . . . . . . . . . . . . . . . .6Fig. 211 . . . . . . . . . . . . . . . . . . . . . .7Fig. 300 . . . . . . . . . . . . . . . . . . . . . .7Fig. 301 . . . . . . . . . . . . . . . . . . . . . .7Fig. 400 . . . . . . . . . . . . . . . . . . . . .7Fig. 600 . . . . . . . . . . . . . . . . . . . . .7
Fig. 602 . . . . . . . . . . . . . . . . . . . . .8Fig. 607 . . . . . . . . . . . . . . . . . . . . . .8Fig. 1002 . . . . . . . . . . . . . . . . . . . .8Fig. 1502 . . . . . . . . . . . . . . . . . . . .8
Gruvlok® CouplingsFig. 7004 HPR Coupling . . . . . . . .9Fig. 7004 EG Coupling . . . . . . . . .9Fig. 7305 HDPE Coupling . . . . . . .9Fig. 7307 HDPE Transition Coupling .10Fig. 7401 Rigidlok Coupling . . . .10Fig. 7000 Lightweight FlexibleCoupling . . . . . . . . . . . . . . . . . . . .10Fig. 7400 RigidLiteTM Coupling . .10Fig. 7005 RoughneckTM Coupling .10Fig. 7003 HingelokTM Coupling . .10Fig. 7010 Reducing Coupling . . .11
Gruvlok® FittingsFig. 7012 Flange . . . . . . . . . . . . .11Gruvlok High Pressure End GuardFittings . . . . . . . . . . . . . . . . . . . . .11Gruvlok Plain-End Fittings . .11-13
Oil Field CouplingsCarbon Steel Merchant Couplings .14JB Smith Sub & Comb. Couplings .14API Line Pipe Couplings . . . . . . .14
Forged Steel Fittings and NipplesForged Steel Fittings . . . . . . . . . .15Steel Pipe Nipples . . . . . . . . . . . .15IPC Coatings . . . . . . . . . . . . . . . .15
Anvil Pipe HangersFig. 264 Pipe Stanchion . . . . . . .16Fig. 259 Pipe Stanchion Saddle .16Fig. 295 Double Bolt Pipe Clamp .16Fig. 46 Universal Trapeze Assembly .16
Anvil-Strut Strut and Strut Fittings . . . . . .17-18
Anvil Design Services . . . . . . . . .19Gruvlok Gasket Selection Guide 20Gruvlok Tools . . . . . . . . . . . . . . . .21Terms and Conditions . . . . . . . . .22
I
AP M
O
FOUNDED192
6
LISTED
PST&ESISBCCI ®
™
VdSISO 9001ISO 9001
APPROVED
Gruvlok Series 7500 Ball ValvesGruvlok Series 7500 Ball Valve line consists of 2” to 6” standard port
2-way valves, and full port diverter valves. All valves are available inseveral configurations to address a broad spectrum of applicationrequirements. Pressure ratings of 740 psig CWP in a ductile iron bodyand 720 psig CWP in a stainless steel body.The Series 7500 carries a generous factor of safety for pressureretention and stem strength, blow-out proof stem design, excellentseat performance, low operation torque, and high Cv. A rugged handleis provided as standard — an integral actuation mounting is included toaccommodate automation.The standard construction is NACE compliant, with ASTM A-395 ductileiron body and end, chrome plated carbon steel trim, RTFE seats andfluorocarbon stem and body seals. The DI valve is available with 316stainless ball and stem.The all stainless steel valves, available in 2-way and 3-way diverterarrangements, incorporate additional features for more demandingapplications. These valves include standard RTFE seats, live loadedPTFE chevron stem seals, and lock-out provisions.
Oil & Gas Products4
Gruvlok Series 7700 ValvesFor use in grooved end pipe systems Sizes: 2"–12" ISO 9001FEATURES:• 300 psi bubble-tight shutoff with Dead-End Service at full rated pressure.• Constant DISC-TO-SEAT loading provided by unique spherical bore of disc
seat area.• Increased valve life with low operating torques.• Thin profile disc provides outstanding flow characteristics and precise
flow control.• Strong stem to disc connection for unparalleled durability• Secure one-piece ductile body for strength and impact resistance.• Versatile nylon coated body inside and out for full corrosion protection.• Elastomer encapsulated disc provides excellent chemical resistance for a
range of applications.• EPDM or Nitrile disc coatings standard with other body coating options
available• Standard lockable handle of ductile iron and plated steel for sturdiness
Gruvlok Grooved End Diverter ValvesTwo inch full port ball valvePressure Rating: 740 psig CWP in ASTM A-395 Ductile Iron body
720 psig CWP in ASTM A-351 CF8M Stainless Steel bodyBody Materials: Stainless Steel
Ductile IronCoated options available
Valves
5
Swages, Bull Plugs, Tubing & Casing Nipples
Tubing NipplesS1-3-1/2” Upset and non-upset ends. Lengths are 4” – 18”. Tubing nipples areavailable with any combination of current API threads (8 round, 10 round, 11-1/2v, etc.) and are stock items in J-55, K-55, N-80 and L-80. Wall thicknessesavailable are standard through double extra heavy. For a different grade ofmaterial (stainless, brass, etc.) and different threads, consult factory.
Casing Nipples4-1/2” O.D. – 13-5/8” O.D.
Line Pipe SwagesSizes range 1/8” – 10”. Swages are manufactured out of A106 Grade B seamlesspipe or cold drawn bar, which is heat treated in accordance with ASTM A234.Choice of raw material is dependent on size and reduction. Swages are manufac-tured in standard, extra heavy, double extra heavy or schedule 160. End finishesavailable are current API threads, beveled for weld, square cut (socket weld) orgrooved. All line pipe swages are available concentric and eccentric.
Oil Country Swages2” and up 8 R.D. Through 10-3/4” O.D.
J.B. Smith is the leading manufacturer of oil country tubular fittings,swages, and bull plugs. J.B. Smith is dedicated to a continuousquality improvement process to help maximize all aspects of thecompany to service our customers.
Full TraceabilityAll J.B. Smith swages, bull plugs, tubing and casing nipples, andchambers are traceable to the original mill test report. To ensurethe traceability all fittings are steel stamped as follows:
Material Specifications WPB S9 (Line Pipe Only)J-55, N-80 etc.
Raw Material Code Each is stamped with a three letter code for identifying raw materi-al type, details of purchase, and mill test report.
Heat Treatment When marked WPB S9 an acceptable heat treatment is under-stood to have been performed. Fittings cold or hot formed frompipe bear an additional two letter code for final heat treatmenttraceability.
All J.B. Smith manufacturing conforms to the following specifications:
Depend on J.B. Smith for excellent services, high quality fittings,and full traceability.
API 5B– ThreadedAPI 5CT – License End FinishingsANSI B16.9 – Weld BevelsMSS-SP-95– Swages and Bull PlugsASTM A234-WPB-2000 – Heated Treatment Raw MaterialASTM B633 Type III – Zinc ElectroplateCHARPY IMPACT – As RequiredN.A.C.E. - MR-01-75 – As RequiredD.N.V. – As Required
Bull PlugsSizes range 1/8” – 10”. 2” and smaller bull plugs are manufactured out of cold drawn bar, which is heattreated in accordance with ASTM A234.2-1/2” – 10” bull plugs are manufactured out of A106 Grade B seamless pipeusing J.B. Smith’s unique spinning process, which ensures uniform wall thickness.Bull plugs are available in standard, extra heavy, double extra heavy, schedule 160,or solid. All Smith bull plugs can be tapped. End finishes available are current APIthreads, beveled for weld, square cut (socket weld) or grooved.
6
Figure 2002,000 PSI CWP - 138 BarSizes: 1” – 16” A general purpose union. Threaded and butt weld ends available.
Catawissa has been a leading manufacturer of quality industrial Forged Steel and Oilfield Wing Unions since 1942. Our Oilfield WingUnion products range in size from 1” to 16” and include the standard ball and cone design plus our unique Figure 300 Flat Facedesign, where space and pipe line separation are a consideration.
Full Traceability:All Catawissa Oilfield Wing Unions are fully traceable and are available with complete mill certifications upon request.
Interchangeability:All Catawissa Oilfield Wing Unions are machined to rigid quality standards ensuring that like components of the same size, figurenumber and pressure rating are fully interchangeable in the field. Catawissa Oilfield Unions are interchangeable with most leadingunion manufacturers.
Standard and Sour Service:Catawissa Unions are available for both Standard and Sour Gas Service. Catawissa Oilfield Sour Gas Unions meet or exceed NationalAssociation of Corrosion Engineers standard NACE MR-01-75 and API RP-14E, and are made in an ISO 9000 certified facility.
Full Range of End Connections:Catawissa Oilfield Wing Unions are also available in threaded ends as well as butt weld and non-pressure seal ends. When youchoose Catawissa you receive the utmost in quality, the widest selection and unmatched on-time deliveries.
Figure 1001,000 PSI CWP - 69 BarSizes: 2” – 8”Low pressure service. Manifold and general service. Female threaded ends. 2” available with 8RDthread. Consult Factory.
Wing Unions
Oil & Gas Products
Figure 2022,000 PSI CWP - 138 BarSize: 4"O-Ring seated dead-end cap. Perfect for transport and completion and stimulation services.
Figure 2062,000 PSI CWP - 138 BarSizes: 1” – 10” O-Ring in male sub for improved sealing. Available in threaded and weld ends.
7
Figure 300Flat Face 2,000 PSI - 138 BarSizes: 1” – 4” Unique Flat-Face Design permits lateral removal of valves and fittings without linespreading.
Wing Unions
Figure 3013,000 PSI CWP - 207 BarSizes: 1”, 2”, 3”Ideal Steam Service Union.
Figure 2112,000 PSI CWP - 138 BarSizes: 1”, 2” Insulating Union. Laminated rings provide full insulation from electrolytic corrosion. Total of 35million Ohms resistance. O-Ring in male sub and seal ring female sub provide primary and sec-ondary seals. All seal rings are field replaceable. Available in threaded and butt weld ends.
Figure 4004,000 PSI CWP - 276 BarSizes: 2”, 3”, 4” Ideal for manifold and pumping service. Available in threaded and weld ends.
Figure 6006,000 PSI CWP - 414 BarSizes: 1” – 4” Features bronze seat for primary seal to prevent rust and corrosion conditions in well servicingand drilling. Available in threaded and weld ends.
8
Figure 100210,000 PSI CWP - 690 BarSizes: 1” – 4” Alloy steel forgings for use in high pressure manifold and treating iron connections. Field replace-able lip-type elastomer seal protects the metal to metal seal. Available for sour gas service.Available in threaded and welded ends.
Catawissa QuickReference Chart
Figure 6076,000 PSI CWP - 414 BarSizes: 1-1/2”, 2”Ideal for hot oil trucks and any application similar to Figure 602. Extended Subs allow forquick breakout on trucks and manifolds. metal to metal connection.
Figure 150215,000 PSI CWP - 1304 BarSizes: 1-1/2”, 2”, 3”Alloy steel forgings for use in high pressure manifold and treating iron connections. Fieldreplaceable lip-type elastomer seal protects the metal to metal seal. Available for sour gasservice. Available in threaded and welded ends.
FIG. NO. 100 200 206 211 300 301 400 600 602 607
1002 1502
Standard Service Sour Service Pipe Size (in.)CWP CWPTEST TEST 1" 11⁄4" 11⁄2" 2" 21⁄2" 3" 4" 6" 8"1,000 2,000 2,000 2,000 2,000 3,000 4,000 6,000 6,000 6,000
10,000 15,000
1,500 3,000 3,000 3,000 3,000 4,500 6,000 9,000 9,000 9,000
15,000 22,500
N/A N/A N/A N/A N/A N/A
4,000 N/A
6,000 N/A
7,500 10,000
N/A N/A N/A N/A N/A N/A
6,000 N/A
9,000 N/A
12,500 15,000
Wing Unions
Oil & Gas Products
Figure 6026,000 PSI CWP - 414 BarSizes: 1” – 4” Compact design is well suited for manifold service. Lip type elastomer seal protects the metal tometal seal. Seal design reduces line turbulence. Available for sour gas service. Available in thread-ed and welded ends.
9
Couplings
Gruvlok Figure 7004 HPRIs designed to provide the versatility of a grooved joint while providing a connection for rigidpipe joint applications. The Fig. 7004 HPR coupling permits working pressure ratings up to 1200psi (82.8 bar).Working Pressure and End Load Values are based on cut grooved standardor extra heavy steel pipe. Fig. 7004 provides a basically rigid joint anddoes not allow for expansion or contraction.Available 2" – 12" nominal pipe sizes.
Gruvlok Figure 7004 EGUses the specially designed “END GUARD” gasket with “EG” grooved pipe. The “EG” gasket hasa center rib that extends between the pipes to provide for pipe end protection, which makes itideally suited for internally lined or coated pipe applications.The Fig. 7004EG Coupling permits working pressure ratings up to 2500 psi(172.4 bar). Working Pressure and End Load Values are based on “EG” cutgrooved standard or extra heavy steel pipe. Fig. 7004EG provides a basi-cally rigid joint and does not allow for expansion or contraction.Available 2" – 12" nominal pipe sizes.
Gruvlok Couplings for Grooved End PipeGruvlok has grown from the early days of standard couplings and fittings to today's broad range of grooved product, plain endproduct, valving, pipe preparation tools, and various accessories.• Provides flexibility above ground and below• Reduces pipe assembly time 50% or more• Provides union at every joint for easy retrofit and maintenance• Leak tight joints
Gruvlok couplings for grooved end pipe are available in nominal pipe sizes 1" through 30" and in metric sizes. The variety ofof coupling designs provides a universal means for the connection of pipe, fittings, and pipe system components. The wideassortment of Gruvlok couplings and gaskets permits selection of the most suitable combination for a specific application,thus providing the most versatile and economical pipe installation.
Material Specifications:Housing:Ductile Iron conforming to ASTM A-536, Grade 65-45-12
Gaskets:EPDM, Nitrile, Fluoro Elastomer, Silicone withproperties as designated in accordance withASTM D-2000 for each gasket grade. EG gasketsare available in high modulus Grade T Nitrileelastomer only.
Fig. 7004HPR withstandard gasket
Fig. 7004EG with "EG" gasketAPPROVED
Gruvlok Figure 7305 HDPE CouplingIs designed for mechanically joining HDPE (high density polyethylene) pipe and fittings. Eachcoupling uses four bolts to drive the sharply machined housing teeth into the outside of thepipe. The teeth are arranged in two banks, each bank consisting of at least two rows of spiralteeth. These effectively grip the pipe, providing a secure mechanical joint with pressure capabili-ties exceeding that of the HDPE pipe itself. Available in 2”-12” diameters.
Gruvlok Figure 7003 HingeLok™ CouplingIs specially designed for applications requiring a quick connection and/or disconnection of a pipejoint. The two coupling halves are hinged for ease of handling and are secured by a cam-actionhandle. Sizes 11⁄2” to 4” use toggle link plates and sizes 5” to 8” use a toggle bolt to attach thecam-action handle to the housings. A locking pin through the handle prevents accidental open-ing of the coupling. The Fig. 7003 Hingelok Coupling allows working pressure ratings up to 300psi (20.7 bar). Available with Viton and silicone gaskets for more critical services. An optionalheavy-duty locking pin can be furnished on request.Available 11⁄2" – 8" nominal pipe sizes.
Figure 7000 Lightweight Flexible CouplingHas a working pressure ratings up to 600 psi (41.4 bar).Fig. 7000 coupling is designed for applications requiring moderate internal pressures. The Fig. 7000coupling is approximately 30% lighter in weight than the Fig. 7001 Coupling. Superior performancein FRAC and cement applications.Available 1" – 8" nominal pipe sizes.
10
Gruvlok Figure 7307 HDPE CouplingAllows for transition from HDPE pipe or fittings to grooved end pipe prepared per Gruvlok standardcut or roll groove specifications for steel pipe or Gruvlok fittings. Machined teeth engage specifical-ly grooved steel pipe or fittings. The banks of teeth on one side of the housing are positionedaway from the gasket, enhancing the sealing capability of the gasket. Temperature and pressurecapabilities exceed the highest temperature and pressure ratings of the HDPE pipe.Available 2" – 12" nominal pipe sizes.
Gruvlok Figure 7401 RigidLok™ CouplingThe Fig. 7401 Rigidlok Coupling installation is fast and easy: remove only one nut and swing thehousing over the gasket and into the grooves. The exclusive Guidelok® feature automatically sep-arates the grooved pipe ends and guides the coupling into position as the bolts are tightened.Precisely sized and oriented tines in the housing key section firmly grip the pipe. The combinationof these designed in features produces a secure, rigid pipe joint connection. This coupling is anideal connector for pumps, valves and fiberglass applications that require a rigid connection. Available 11⁄2" – 24" nominal pipe sizes.
Couplings
Oil & Gas Products
Gruvlok Figure 7400 RigidLite™ CouplingThe Figure 7400 Rigidlite Coupling from Gruvlok is specially designed to provide a rigid, locked-inpipe connection to meet the specific demands of rigid design steel pipe and copper tube systems.Fast and easy swing-over installation of the rugged lightweight housing produces a secure, rigidpipe joint. The Figure 7400 Rigidlite Coupling is UL Listed and FM Approved for 300 psi (20.7 bar)fire protection service in both wet and dry systems with roll grooved or cut grooved steel pipe pre-pared in accordance with Gruvlok grooving specifications. Provides rigidity in rig fire systems.The Figure 7400 Rigidlite Coupling with a DRI-SEAL™ pre-lubricated gasket is intended for use inambient temperature fire protection systems installed in accordance with NFPA Standard 13“Sprinkler Systems”. For other applications, optional EPDM and Nitrile gaskets are furnished.Available 1" – 8" nominal pipe sizes.
Gruvlok Figure 7005 Roughneck™ CouplingIs an efficient and cost effective method of joining either plain end or beveled end pipe. GruvlokPlain End Couplings and Fittings allow a complete piping system to be installed without any pipeend preparation. The Gruvlok Plain End Method is especially suited for repair or cut-in work, aswell as new installations where rigid joints are required. The Roughneck Coupling “grippers” biteinto the outside diameter of the steel pipe, providing for positive rigid joint connections. Availablein 2” - 18” diameters.
11
Couplings
Gruvlok Figure 7010 Reducing CouplingThe Figure 7010 Reducing Coupling makes it possible to directly connect two different pipe sizes,eliminating the need for two couplings and a reducing fitting. The specially designed reducingcoupling gasket with a center rib assures proper positioning of the gasket and prevents thesmaller pipe from telescoping into the larger during assembly. Figure 7010 Reducing Couplingallows for working pressure ratings up to 500 PSI (34.5 bar).ranges 15” of Hg. vacuum to 300psig on standard wall steel pipe.Available 2" – 8" nominal pipe sizes.
Gruvlok Figure 7012 FlangeAllows direct connection of Class 125 or Class 150 flanged components to a grooved piping system.The two interlocking halves of the 2” through 24” sizes of the Gruvlok Flange are hinged for easeof handling, and are drawn together by a latch bolt which eases assembly on the pipe. Precisionmachined bolt hole, key and mating surfaces, assure concentricity and flatness to provide exactfit-up with flanged, lug and wafer styles of pipe system equipment. A specially designed gasketprovides a leak-tight seal on both the pipe and the mating flange face. The 14” through 24” sizesof the Gruvlok Flange are cast in four segments. A sleek profile gasket design allows quick andeasy assembly of the Gruvlok Flange onto the pipe. All Gruvlok Fig. 7012 Flanges have designed-in anti-rotation tines which bite into and grip thesides of the pipe grooves to provide a secure, rigid connection. The Gruvlok Fig. 7012 Flangerequires the use of a metal adapter insert when used against rubber faced surfaces, wafer/lugdesign valves and serrated or irregular sealing surfaces.
Gruvlok High Pressure End Guard FittingsSizes: 2” – 6”Gruvlok End Guard Fittings are fabricated from extra heavy (XS) materials. These fittings may beused for high pressure systems or where lined or coated fittings are required.Available configurations: 90˚ and 45˚ elbows, tees, reducing tees, and crosses.
Gruvlok Fittings for Grooved End PipeGruvlok fittings are available through 24" nominal pipe size in a variety of styles. Use the Fitting Size Table from the Gruvlok catalogto convert nominal pipe size to corresponding pipe O.D. These fittings are designed to provide minimum pressure drop and uni-form strength. Refer to Flow Data in the catalog for details. Depending on styles and size, Gruvlok fittings are provided in variousmaterials including malleable iron, ductile iron, forged steel or fabricated steel. Pressure ratings of Gruvlok standard fittings conform to those of Figure 7001 Gruvlok coupling.
Gruvlok Plain-End FittingsGruvlok plain end fittings are designed for use with the Fig. 7005 Roughneck Coupling only.Available in nominal pipe sizes through 8" in a variety of styles. Depending on size and configu-ration, fittings are either segment-welded steel or forged steel.
Fittings
12
Material Specificationsu Cast Fittings:
Ductile iron conforming to ASTM A 536 or Malleable iron conformingto ASTM A 47
u Fabricated Fittings:1-4" Carbon steel, Schedule 40, conforming to ASTM A53, Grade B5-6" Carbon steel, Schedule 40 conforming to ASTM A53, Grade B8" Carbon steel, Schedule 30, conforming to ASTM A53, Grade B
u Coating:Rust inhibiting lead-free paint, ORANGE (Standard), RED (Optional)Hot-dipped zinc galvanized (Optional). For other coatings contact Gruvlok.
The Fitting SizeChart is used todetermine the ODof the pipe thatthe fitting is to beused with.Gruvlok Fittingsare identified byeither theNominal size ininches or the PipeOD in mm.
FITTING SIZENom. Size Pipe OD Nom. Size Pipe OD In. /DN(mm) In. /mm In. /DN(mm) In. /mm
1 1.315 41⁄4 OD 4.25025 33.7 100 108.011⁄4 1.660 5 5.56332 42.2 140 141.311⁄2 1.900 51⁄4 OD 5.23640 48.3 125 133.02 2.375 51⁄2 OD 5.500
50 60.3 125 139.721⁄2 2.875 6 6.62565 73.0 150 168.3
3 OD 2.996 61⁄4 OD 6.25965 76.1 150 159.03 3.500 61⁄2 OD 6.500
80 88.9 150 165.131⁄2 4.000 8 8.62565 101.6 200 219.14 4.500
100 114.3
Gruvlok Figure 7050Standard 90˚ Elbow
Gruvlok Figure 7060Standard Tee
Gruvlok Figure 7072Concentric Reducer
Fittings
Oil & Gas Products
13
Gruvlok Figure 7051Standard 45˚ Elbow
Gruvlok Figure 7061Reducing Tee
Gruvlok Figure 7050LR Long Radius 90˚ Elbow
Gruvlok Figure 7051LR Long Radius 45˚ Elbow
Gruvlok Figure 7075Bull Plug
Gruvlok Figure 7077Swaged Nipple
Gruvlok Figure 7068Cross
Gruvlok Figure 7074End Cap
Gruvlok Figure 7063Threaded Tee
Gruvlok Figure 7064Reducing Threaded Tee
Fittings
14
JB Smith Sub & Combination CouplingsJ.B. Smith’s full range of Sub-Tubing and Combination Couplings are availablein regular, EUE, and round, sharp and combination threads.Sizes 2” regular through 4” EUEMaterial J-55 and N-80
API Line Pipe CouplingsSizes 1/8” – 12”These couplings are manufactured in accordance with American PetroleumInstitute Specification 5L. All sizes are taper tapped 3/4” per foot on the diameter.Line pipe couplings in sizes 1/8” – 1-1/2” are dipped in rust preventative.Couplings in sizes 2” and larger are phosphated.
Carbon Steel Merchant CouplingsSizes 1/8” – 6”Manufactured in accordance with ASTM specification A865. Merchant cou-plings in sizes 1/8” through 2” are normally supplied straight tapped. Sizes 2-1/8” and larger are taper tapped. Taper tapped standard merchant couplingsin sizes 1/8” through 2” are available upon request. API line pipe couplingsare used in all sizes over 6”. Couplings from 1/8” through 2” are dipped inrust preventative. Couplings 2-1/8” and larger are phosphated. Galvanized fullcouplings are also available.
Oil Field Couplings
Oil & Gas Products
15
Steel Pipe NipplesAnvil nipples are manufactured in accordance with ASTM SpecificationsA733 – Welded and seamless carbon steel nipples (A53 C/W and 106SMLS). Where possible, each nipple is identified with Anvil Trademark,Seamless or Welded indication, Pipe Schedule and Material designation.Anvil can supply special nipples pertaining to lengths, threading and finishes.
Forged Steel FittingsSteel Pipe Fittings add an important dimension to the industry-leading lineof flow control products already offered by Anvil. Anvil is a respected nameand its products are well-regarded for high quality and consistency.
Materials:The Anvil Forged Carbon Steel Fittings consist of forgings, bars, seamless pipeor tubes which conform to the requirements for melting process, chemicalcomposition and mechanical properties of ASTM A105.
Design Basis:ASME B16.11 — Forged fittings, socket welding and threaded.
Dimensions:ASME B16.11, unless otherwise noted. All catalog dimensions are in inches.
Threads:ASME 1.20.1
Forged Steel Fittings and Nipples
IPC COATINGSScotchkote 134A fusion bonded epoxy coating designed for corrosion protection of metal.Coating is resistant to wastewater, corrosive soils, hydrocarbons, harshchemicals, brine and saltwater. Also can be used in potable water services.
Corvel 1660Designed to protect the inside diameter of tubular goods fromcorrosive environment encountered in the oil and gas industry. Typicalapplications include fittings, valves, drill pipe, sucker rods and meteringsystems. Coating is resistant to H2S, acids, CO2, harsh chemicals, brine andsaltwater.
For additional information regarding IPC Coatings please contact an Anvilrepresentative.
16 Oil & Gas Products
Pipe Hangers
Anvil Figure 259 Pipe Stanchion SaddleCast iron stanchion saddle with steel yoke and nuts. Size range: 4 through 36inch pipe.
FEATURES:• U-bolt yoke provides stability
Anvil Figure 295 Double Bolt Pipe ClampRecommended for suspension of pipe requiring insulation and where flexibility of the clamp is desirable. Size range: 3⁄4 through 36 inch.
FEATURES:• Accommodates up to 4" thick insulation.• Load ratings meet ASME code requirements and are substantiated by
laboratory test.
Anvil Figure 264 Pipe StanchionStanchion-type support where vertical adjustment of steel pipe is required.
FEATURES:• Vertical adjustment of approximately 41⁄2 inches.• Saddle supports a broad range of pipe sizes.
Anvil Figure 46 Universal Trapeze AssemblyTrapeze assembly is to be suspended by two rods. Designed for top loading exclusively.
Anvil's large and complete line of pipe hangers is based on over a century of experience in the industrial piping field. Anvil furnisheshangers and supports for a wide range of industrial markets, including Power, Petrochemical, Refinery, and Pulp and Paper.
Anvil's domestic manufactured pipe support product offerings include Pipe Clamps, Clevises, Structural and Concrete Attachments,Brackets, Pipe Saddles and Rollers, Slides and Anchors, and Pipe Alignment Guides. Anvil also offers capabilities in providing SpecialFabrication and miscellaneous Structural Steel Fabrication.
1122
33
The Anvil-Strut Connection, Easy as 1 – 2 – 3 …
Insert the clamping nut anywhere along thecontinuous slot channel. A 90˚ clockwise turnpositions the grooves and teeth in the nut with theinturned edges of the channel
The strut fitting provides theconnection of channels
Tighten the bolt(s) to secure theconnection
Strut and Strut FittingsContinuous Metal Framing
17
Strut and Strut Fittings
Anvil-Strut offers a complete line of continuous slot metal framing complete with channels, fittings and accessories forany framing or support problem...large or small, heavy or light.
Anvil-Strut’s offering comes complete with exacting standards of research, design, engineering and manufacturing.Maximum recommended load ratings for channels have been established through testing and are based on allowablestresses applicable to strut material specifications.
Beyond the versatility that strut and strut fittings offer as a basic building material, metal framing is popular for more exoticapplications such as clean rooms, satellite dish supports, x-ray supports, storage racks, theater screens, tunnel stanchions andoffshore catwalks.
TRAPEZE SUPPORT SYSTEM
Anvil-Strut metal framing is ideal for electricaland mechanical pipe support applications.
PlasticEnd Cap(For safety)
Pre-slotted channel allowthrough channel connections
SquareWasherPS 619
Acceptable Methods to Hang Channels
Threaded Rod
TRAPEZE SUPPORT SYSTEM
Anvil-Strut metal framing is ideal for electricaland mechanical pipe support applications.
PlasticEnd Cap(For safety)
Pre-slotted channel allowthrough channel connections
SquareWasherPS 619
Acceptable Methods to Hang Channels
Threaded Rod
STANDARD CHANNEL AND FITTING ASSEMBLY
The factory punched holes in “ H” series channelallow fittings to be attached to either side.
Just loosen the
nuts to easily
adjust position
FLOOR MOUNTED STAND
Utility PipingConduit
Island stands allow you to mount equipment or piping on both sides in trenches and in service isles.
ElectricalPanel
Metal framing is ideal for mounting electrical or telecommunication panels. It allows you to create a floor stand, suspend panels from an overhead beam or even attach panels to adjacent structural steel. Bracing may be added for heavier load requirements.
ELECTRICAL PANEL SUPPORTS
TRAPEZE SUPPORT SYSTEM
Anvil-Strut metal framing is ideal for electricaland mechanical pipe support applications.
PlasticEnd Cap(For safety)
Pre-slotted channel allowthrough channel connections
SquareWasherPS 619
Acceptable Methods to Hang Channels
Threaded Rod
Standard Channel andFitting Assembly
Floor Mounted Stand
Electric PanelSupports
Trapeze Support System
GANGED PIPE SUPPORT
Standard “ I” beam
Standard channel
Pipe clamps
Pipe clamp fittingsPS 1100 (typical)
Standard back-to-backcombination channel
Plastic End Cap (typical)
Anchor(suitable for wall material)
Square WasherPS 619 w/Hex Nut
OVERHEAD SUPPORTVERTICAL TO HORIZONTAL
Pipe clamp fittingsPS 1100 (typical)
Standard back-to-backcombination channel
Plastic End Cap (typical)
Anchor(suitable for wall material)
Square WasherPS 619 w/Hex Nut
OVERHEAD SUPPORTVERTICAL TO HORIZONTAL
Ganged Pipe SupportVertical to Horizontal
18 Oil & Gas Products
Strut and Strut Fittings
B
M-1
CHILLED WATER ISO
NO SCALE
36
36
32
32 65
64
3332
32
9036
32
58
32
3266 54
5932
3532
5832
54
6054
32
3052
545556
63
9036
32
5832
32
5832
62
5454
61
54 60
54 59
5459
54
39
90
36
32
3732
36
32
3432
3332
31
90
36
3238
3236
32
34
32
72
59
54
5466
32
69
32
32
36
3257
56
5453545754
55
54
5954
66
32
69
32
36
32
32
80
73
74
41
40
80
81
80
82
80
87
86
8687
8082
80
81
89
8980
80
8280 58
82
80
5880
80
50
Features, Advantages, BenefitsuStandardized facility constructionuAccurate battery take-offsuRepresentation on your locationuFaster retrofit turnarounds
ApplicationsOnshore Production Facilities Offshore Rigs and Platformsu Tank batteries u Design layout for grooved pipingu Water floods u Drain systemsu CO2 floods u Fuel linesu Header systems u Bulk storage and delivery systemsu Gas processing u Air systems
Anvil's unique design services group for conceptualizing to finalizing projects.
Providing complete three-dimensional drawings for threaded, grooved systemsapplications.
19
Design Services
“C ” StyleThe “C” Style cross section configurationis the most widely used gasket. It is thegasket style provided as standard inmany Gruvlok Couplings (Fig. 7000,7001, 7003, 7004, 7307, 7400 and7401). Grade “E” and “T” are standardgrades while other grades are availablefor special applications.
Roughneck®
This “C” Style gasket is similar in appear-ance and design to the Standard gasket butis only used with Fig. 7005 RoughneckCouplings and Fig. 7305 HDPE Couplings.The Roughneck gasket is wider, whichallows for minor pipe end separation asline pressure sets the grippers into theplain end pipe.
End Guard®
The protecting rib fits between the endsof lined pipe to prevent damage tounprotected pipe ends during couplingjoint assembly.The EG gasket is provided as standardwith the Fig. 7004EG Coupling.The EG gasket is available only in high-modulus Grade "T" elastomer.
Gruvlok Gasket StylesGruvlok offers a variety of pressure responsive gasket styles. Each serves a specific
function while utilizing the same basic sealing concept. Proper installation of the gasketcompresses the inclined gasket lips on the pipe O.D., forming a leak-tight seal. This seal-ing action is reinforced when the gasket is encompassed and compressed by the cou-pling housings. The application of internal line pressure energizes the elastometric gasketand further enhances the gasket sealing action.
STANDARD GASKETS*Temperature Color
Grade Range Compound Code General Service Application-40˚F to +230˚F Water, dilute acids, alkalies, salts, and many chemical services notE (-40˚C to 110˚C) EPDM Green involving hydrocarbons, oils, or gases. Excellent oxidation resistance.
NOT FOR USE WITH HYDROCARBONS-20˚F to +180˚F Petroleum products, vegetable oils, mineral oils, and air contaminatedT (-29˚C to 82˚C) Nitrile Orange with petroleum oils.
(Buna-N) NOT FOR USE IN HOT WATER SERVICES
STANDARD GASKETS FOR PETROLEUM PRODUCTS*Temperature Color
Grade Range Compound Code General Service Application+20˚F to +300˚F High temperature resistance to oxidizing acids, petroleum oils, hydraulic fluids,O (-20˚C to 149˚C) Fluoro Blue halogenated hydrocarbons and lubricants.
Elastomer
Gasket Grade Index
PETROLEUM PRODUCTS
Gasket GasketService Grade Service GradeCrude Oil - Sour T JP-6, 100˚F (38˚C) Maximum Temp. ODiesel Oil T Kerosene TFuel Oil T Lube Oil, to 150˚F (66˚C) TGasoline, Leaded T Motor Oil TGasoline, Unleaded* (O) Tar and Tar Oil THydraulic Oil T Transmission Fluid -- Type A OJP-3, JP-4 and JP-5 T/O Turbo Oil #15 Diester Lubricant O
Gasket Recommendation Listing
Where more than one gasket grade is shown the preferred gasket grade is listed first.Where the gasket grade is shown in parentheses, contact Gruvlok for an engineeringevaluation and recommendation.Specify gasket grade when ordering. Use Gruvlok lubricant on gasket. Check gasketcolor code to be certain it is recommended for the service intended.
Unless otherwise noted, all gasket listings are based upon 100˚F (38˚C) maximum temperature service conditions.For services not listed, contact Gruvlok for recommendation.*Contact Gruvlok for service evaluation.
*Note: Other gasket compounds and details available on request
20
Gasket Selection Guide
Oil & Gas Products
Model 3007 Roll GrooverModel 1007 Roll Groover
u WIDE GROOVING RANGE2" thru 16" standard wall & schedule 10 steel pipe, 2" thru 12" Schedule 10S and 40S Stainless Steel and2" thru 8" copper tube type K, L, M, and DWV.
u PIPE LENGTHS20' random schedule 40 (standard wall) to 5" groove bygroove nipples. The shortest roll groove nipple capabilityin the industry; hands-clear operation.
u HANDS CLEAR GROOVING OF PIPE AND NIPPLESEnhanced operator safety provided by outboard guide rollassembly.
u ACCURATE, REPEATABLE-GROOVE DIAMETER CONTROLSimplified direct action design provides positive, repeat-able, control.
u FAST GROOVING TIMESLarge capacity two-stage pump. Two-stage design savestime engaging pipe while providing smooth application ofoptimum grooving force with reduced operator effort.
u BETTER CONTROL OF PIPE FLAREOutboard guide roll assembly registers pipe for properorientation.
u QUICK, EASY SETUP AND ROLL CHANGE
u RUGGED DESIGN REQUIRES ZERO MAINTENANCESealed bearings eliminate need for periodic maintenance.
u USER FRIENDLY DESIGNPump location is adjustable for operator comfort andsafety.
u EASE OF OPERATIONHigh grooving forces obtained through use of larger capa-bility ram requires less pump effort.
u FOOT SWITCH POWER APPLICATION
u OPERATOR SAFE DESIGN
Features:
21
Tools
The new Gruvlok Model 1007 and Model 3007 Roll Grooversoffer an advanced zero maintenance design to make rollgrooving a more efficient, safer and easier task saving bothtime and money. Fast, accurate and repeatable grooves arethe standard for all pipe sizes from 2" through 16" on pipe
lengths from 5" to 20 feet and all with hands clear operation.Quick and easy to set up with foot switch operation, rollgrooving is now user friendly. Call your Gruvlok branch for ademonstration of the future of roll grooving.
22 Oil & Gas Products
1. CONTROLLING PROVISIONS: These termsand conditions shall control with respectto any purchase order or sale of Seller’sproducts. No waiver, alteration or modifi-cation of these terms and conditionswhether on Buyer’s purchase order orotherwise shall be valid unless the waiver,alteration or modification is specificallyaccepted in writing and signed by anauthorized representative of Seller.
2. DELIVERY: Seller will make every effort tocomplete delivery of products as indicat-ed on Seller’s acceptance of an order, butSeller assumes no responsibility or liabili-ty, and will accept no back charge, for lossor damage due to delay or inability todeliver caused by acts of God, war, labordifficulties, accident, delays of carriers, bycontractors or suppliers, inability to obtainmaterials, shortages of fuel and energy, orany other causes of any kind whatsoeverbeyond the control of Seller. Seller mayterminate any contract of sale of its prod-ucts without liability of any nature, bywritten notice to Buyer, in the event thatthe delay in delivery or performanceresulting from any of the aforesaid causesshall continue for a period of sixty (60)days. Under no circumstances shall Sellerbe liable for any special or consequentialdamages or for loss, damage, or expense(whether or not based on negligence)directly or indirectly arising from delays orfailure to give notice of delay.
3. WARRANTY: Seller warrants for one yearfrom the date of shipment Seller’s manu-factured products to the extent that Sellerwill replace those having defects in mate-rials or workmanship when used for thepurpose and in the manner which Sellerrecommends. If Seller’s examination shalldisclose to its satisfaction that the prod-ucts are defective, and an adjustment isrequired, the amount of such adjustmentshall not exceed the net sales price of thedefective products only and no allowancewill be made for labor or expense ofrepairing or replacing defective productsor workmanship or damage resultingfrom the same. Seller warrants the prod-ucts which it sells of other manufacturersto the extent of the warranties of theirrespective makers. Where engineeringdesign or fabrication work is supplied,Buyer’s acceptance of Seller’s design or ofdelivery of work shall relieve Seller of allfurther obligation, other than asexpressed in Seller’s product THIS ISSELLER’S SOLE WARRANTY. SELLERMAKES NO OTHER WARRANTY OF ANYKIND, EXPRESSED OR IMPLIED AND ALLIMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PAR-TICULAR PURPOSE WHICH EXCEED SELL-ER’S AFORESTATED OBLIGATION AREHEREBY DISCLAIMED BY SELLER ANDEXCLUDED FROM THIS WARRANTY. Sellerneither assumes, nor authorizes any per-son to assume for it, any other obligationin connection with the sale of its engi-neering designs or products. This warran-ty shall not apply to any products or partsof products which (a) have been repairedor altered outside of Seller’s factory, inany manner; or (b) have been subjectedto misuse, negligence or accidents; (c)have been used in a manner contrary toSeller’s instructions or recommendations.Seller shall not be responsible for designerrors due to inaccurate or incompleteinformation supplied by Buyer or its rep-resentatives.
4. SELLER’S LIABILITY: Seller will not beliable for any loss, damage, cost ofrepairs, incidental or consequential dam-ages of any kind, whether based uponwarranty (except for the obligationaccepted by Seller under “Warranty”above), contract or negligence arising inconnection with the design, manufacture,sale, use or repair of the products or ofthe engineering designs supplied toBuyer.
5. RETURNS: Seller cannot accept return ofany products unless its written permissionhas been first obtained, in which casesame will be credited subject to the fol-lowing: (a) All material returned must, onits arrival at Seller’s plant, be found to bein first-class condition; if not, cost of put-ting in saleable condition will be deduct-ed from credit memoranda; (b) A han-dling charge deduction of twenty percent(20%) will be made from all credit mem-oranda issued for material returned; (c)Transportation charges, if not prepaid, willbe deducted from credit memoranda.
6. SHIPMENTS: All products sent out will becarefully examined, counted and packed.The cost of any special packing or specialhandling caused by Buyer’s requirementsor requests shall be added to the amountof the order. No claim for shortages willbe allowed unless made in writing withinten (10) days for products damaged orlost in transit should be made on the car-rier, as Seller’s responsibility ceases, andtitle passes, on delivery to the carrier.
7. SPECIAL PRODUCTS: Orders covering spe-cial or non-standard products are notsubject to cancellation except on suchterms as Seller may specify on applica-tion.
8. PRICES AND DESIGNS: Prices and designsare subject to change without notice. Allprices are F. O. B. Point of Shipment,unless otherwise stated.
9. TAXES: The amount of any sales, excise orother taxes, if any, applicable to the prod-ucts covered by this order, shall be addedto the purchase price and shall be paidby Buyer unless Buyer provides Sellerwith an exemption certificate acceptableto the taxing authorities.
10. NUCLEAR PLANTS: Where the products,engineering design or fabrication is fornuclear plant applications, Buyer agrees:(a) to take all necessary steps to addSeller as an insured under the AmericanNuclear Insurers’ (ANI)-pool and underthe Mutual Atomic Energy ReinsurancePool (MAERP) for property damage andliability insurance and if necessary stepscould have been taken, but are not taken,Buyer shall hold Seller harmless againstall such losses which could have beenthus covered, (b) to hold Seller harmlesswith respect to any personal injury (ordeath), property damage or other loss ina nuclear incident which is caused directlyor indirectly by defective de-sign, material,or workmanship furnished by Seller andwhich is covered by insurance maintainedby Buyer (or which could be so coveredbut with respect to which Buyer haselected to self-insure), and further agreesto waive subrogation by its carriers ofsuch insurance against Seller, and (c) asto nuclear hazards for which Buyer can-not obtain insurance coverage, the liabilityof Seller for any personal injury (ordeath), property damage or other lossdirectly caused by defective design, mate-rial, or workmanship furnished by Sellershall not exceed the value of the materialfurnished by Seller at the time of the lossoccurrence.
11. MINIMUM INVOICE: $25.00 plus trans-portation.
12. TERMS: Cash, net 30 days unless other-wise specified.
Terms and Conditions
1850 Providence Steam & Gas Pipe Co. is formed, and Frederick Grinnell purchases a controlling interest.
1919 General Fire Extinguisher Co. becomes Grinnell® Co.
1909 Frederick Grinnell opens a foundry in Cranston, RI.Companies express interest in buying its piping products, laying the groundwork for what would become the Grinnell Supply Sales Division. It would be these manufacturing and sales operations that eventually become Anvil International.
1969 Grinnell Co. is acquired by International Telephoneand Telegraph. Two years later, ITT divests the FireProtection Division, but keeps the manufacturing and sales divisions that will become known as Anvil International.
1999 Tyco sells the distribution and manufacturing operations known up to this point as “Grinnell Supply Sales,” but keeps the Grinnell® trademark.
1994 J.B. Smith and Catawissa join the Grinnell Supply Sales and Manufacturing division.
2000 The industry’s trusted manufacturer of pipe fittings, hangers and grooved fittings is renamed Anvil International, Inc.
2001 Anvil International acquires Merit Manufacturing and Beck Manufacturing.
2004 Anvil International acquires Star Pipe Products, Building and ConstructionDivisions (SPF) and forms AnvilStarTM Fire Products Division.
Today Anvil International is the largest and most complete fitting and hangermanufacturer in the world.
1960 Gruvlok line of grooved fittings is introduced.
B U I L D I N G C O N N E C T I O N S T H A T L A S T
ANVIL BRANDS:
We built our reputation from the ground up.
Anvil’s history stretches back to the mid 1800s, whena company named Grinnell® began providing its customers with the finest quality pipe products. Since2000, those quality products and services—and thepeople who provide them—have been known as Anvil International. Anvil customers receive the quality and integrity that have been building strong connections in both products and businessrelationships for over 150 years.
TRUSTED FOR 150 YEARS
Focused Product Line:
Anvil® Malleable and Cast Iron Threaded Fittings
SPFTM Cast Iron and Ductile Iron Threaded Fittings
Anvil® Engineered Hangers,Staple Hangers, Supports andStruts
Anvil® Seamless Pipe Nipples
Beck Welded Pipe Nipples
SPFTM Steel Pipe Nipples
J.B. Smith Swage Nipples and Bull Plugs
Anvil® Steel Pipe Couplings,Forged Steel Fittings and SmallSteel Fittings
Gruvlok® Couplings, Fittings and Valves
SPFTM Grooved Couplings, Fittings and Flanges
Merit® Tee® Lets and Drop Nipples
SPFTM O’Lets
Catawissa® Wing Unions and Check Valves
To find out more about our products and services, or to get help updating your specifications and files to our new name, call Anvil at 1-603-422-8000 or visit www.anvilintl.com.
Grinnell® is a registered trademark of Grinnell Corporation, a Tyco International Ltd. Company.
#320 / Printed in USA / RPI / 12.05 / 2.5M / ©2005
CANADAMichael J. Warne, General Manager470 Seaman StreetStoney Creek, Ontario L8E 2V9Tel: 905-664-1459 • Fax: 905-664-3190
EUROPE & MIDDLE EAST REGIONRick van Meesen, Sales DirectorThe NetherlandsTel: +31 53 5725570 • Fax: +31 53 5725579U.S. Customer Service Tel: +1 708 534 1414
LATIN AMERICAU.S. Customer Service Tel: +1 708 534 1414Fax: +1 708 534 5441
PUERTO RICOR.R. Barril, Inc.Tel: +1 787 982 1550 • Fax: +1 787 982 1570U.S. Customer Service Tel: +1 708 534 1414
MEXICOJose Antonio BuenoMexico Tel: +52 777 169 4546U.S. Customer ServiceTel: +1 708 534 1414 • Fax: +1 708 534 5441
Corporate Offices110 Corporate Drive, Suite 10 • P.O. Box 3180 • Portsmouth, NH 03802-3180Tel: 603-422-8000 • Fax: 603-422-8033E-mail address — [email protected]
For Sales and Service Information Contact the Regional ServiceCenter Nearest You or Visit Our Website at www.anvilintl.com
EASTERN REGION Servicing: Connecticut, Delaware, Florida, Georgia,Maine, Maryland, Massachusetts, New Hampshire, NewJersey, New York, North and South Carolina, EastPennsylvania, Rhode Island, Vermont, Virginia
800 Malleable RoadColumbia, PA 17512Tel: 717-684-4400 • Fax: 717-684-8863
NORTHERN REGIONServicing: Illinois, Indiana, Iowa, Kentucky, Michigan,Minnesota, Nebraska, North and South Dakota, Ohio,West Pennsylvania, West Virginia, Wisconsin
750 Central AvenueUniversity Park, IL 60466Tel: 708-534-1414 • Fax: 708-534-5441Toll Free: 1-800-301-2701
SOUTHERN REGION Servicing: Alabama, Arkansas, Kansas, Louisiana,Mississippi, Missouri, Oklahoma, Tennessee, Texas
1313 Avenue RGrand Prairie, TX 75050Tel: 972-343-9206 • Fax: 972-641-8946Toll Free: 1-800-451-4414
WESTERN REGIONServicing: Alaska, Arizona, California, Colorado, Hawaii,Idaho, Montana, Nevada, New Mexico, Oregon, Utah,Washington, Wyoming
1385 Greg StreetSparks, NV 89431Tel: 775-331-7029 • Fax: 775-331-5075Toll Free: 1-800-572-0051
U.S. Regional Service Centers
International Sales RepresentativesEnglish and Spanish Speaking Service Center (Se habla Español)
For Fire Protection Products Contact AnvilStar™750 Central Avenue • University Park, IL 60466 • Tel: 708-534-1414 • Fax: 708-534-5441 • Toll Free: 1-800-301-2701
ANVIL INTERNATIONALWORLDWIDE CUSTOMER SERVICE CENTERTel: +1 708 534 1414 • Fax: +1 708 534 5441