Office Tender

8/6/2019 Office Tender

1/19

!!"

" ! #$ %& ' ($&'$$

)

* + , - , " ($ ./ 0 " 0

'$1.#

2 % 3 $

"$$),

4500,$$

$$

65"%$0$3$$

3"

7-"%0

#),/$.)-%0"%0$

31.#880$0-&/$

.)

9!""#""$#%&"'$(%($!$)*

:/$$/3/$$00$%0;;0

$


2/19

SRNO

DESCRIPTION QTY UNIT

1 Aluminium frame : Providing and fixing in position Aluminium Frame work for amaximum height of 3.5m for partitions, panelling, boxing, soffits etc. with vertical &horizontal members at not more than 600 mm c/c, size of vertical members -

50x50x1.62mm size of horizontal members - 50x25x1.62mm. All complete includingnecessary additional supports, bracing, runner etc so that lateral movement isarrested, as per instructions of Project - in - Charge. Frame work will be measuredand paid as per actual measurement on site. Rates quoted shall include cost ofproviding and fixing supports up to floor ceiling, Angle Support to ceiling. Allcomplete as per detail drawing, as specified and as directed by Architect /Consultant / Project - in - Charge. (Actual executed area will be measured).

3612.50 KG

2 Wooden frame: Providing and fixing in position Wooden Frame work for maximumheight of 3.5m for partitions, panelling, boxing, soffits etc. with vertical & horizontalmembers at not more than 600 mm c/c size of vertical members - 50x50mm size ofhorizontal members - 50x50mm. All complete including necessary additionalsupports, bracing, runner etc so that lateral movement is arrested, as perinstructions of Project - in - Charge. Rate to include one coat painting with fire

retardant paint. Frame work will be measured and paid as per actual measurementat site. Rates quoted shall include cost of providing and fixing supports up to floorceiling, Angle Support to ceiling. All complete as per detail drawing, as specified andas directed by Architect / Consultant / Project - in - Charge. (Actual executed areawill be measured). Height: 1250/2400mm

1542.00 SQM

3 9 MM THICK MARINE PLYWOOD: Providing and fixing 9 mm thick ApprovedMarine Grade Plywood of approved quality & make for partitions, facias, skirtings,wall panelling & soffit etc as per required width and size or as per drawing. Includingcost of making openings for switches, AC facias with the help of adhesives likefevicol etc, nails / screws etc. The rates quoted shall include providing openings forwiring and necessary screws etc. All complete as per detail drawing, as specifiedand as directed by Architect / Consultant / Project - In - Charge. (Actual executedarea will be measured).

2385.00 SQM

4 12 MM THICK MARINE PLYWOOD Providing and fixing in position 12 mm thickApproved Marine Grade Plywood of approved quality & make for partitions, facias,skirtings, wall panelling & soffit etc as per required width and size or as per drawing.Including cost of making openings for switches, AC facias with the help of adhesiveslike fevicol etc, nails / screws etc and providing openings for wiring and necessaryscrews etc. All complete as per detail drawing, as specified and as directed byArchitect / Consultant / Project - In - Charge. (Actual executed area will bemeasured).

450.00 SQM

5 9 MM THICK GYPSUM BOARD ON WALL / PARTITION: Providing and fixingGypsum Board (9 mm thick) to wall / partition in line and level. Rate to include costof filling joints with joint tapes & jointing powder) (Actual execute area will bemeasured).

70.00 SQM

NOTE FOR FINISHES IN PARTITION, PANELING, ETC: - Actual executed area willbe measured as two sides of same partition are likely to have different finishes. Thefinishing material shall be fixed in required divisions/panels/pattern with propergrooves etc. as per drawings & directions. All complete as per detail drawing, asspecified and as directed by Architect / Consultant / Project - In - Charge. It may benoted that for cross grains/pattern etc no additional wastage area will be given inmesurements and quoted rate of the contractor shall include all the above in theirrates.


3/19

6 Veneer Finish in partition Providing and fixing 3.5 to 4.0 mm thick group matchingApproved Decorative Veneer of approved quality and make, of required size andwidth as per site condition including 3 coat of melamine polish on the veneersurface. Additional coat if required for finish surface to be provide free of cost. Thecost shall be including surface preparation, pasting with approved adhesive andfinishing it evenly to get flat surface. The cost of openings for switches, AC facia,any other cutout etc. shall be included in the rates quoted. All complete as per detail

drawing, as specified and as directed by Architect / Consultant / Project - In -Charge. (Actual executed area will be measured). VENEER FINISH (BASIC RATERS 2763/- PER SQM)

575.00 SQM

7 Item same as above VENEER FINISH (BASIC RATE OF VENEER RS 1692/- PERSQM)

480.00 SQM

8 Item same as above VENEER FINISH (BASIC RATE OF VENEER Rs. 956/- PERSQM)

1350.00 SQM

9 Item same as above VENEER FINISH (BASIC RATE OF VENEER Rs. 4510/- PERSQM)

100.00 SQM

10LAMINATE FINISH IN PARTITION (BASIC RATE OF LAMINATE RS 800/- PERSqm) Providing and fixing 1.0 mm thick Laminate of approved quality, make &colour of required size and width as per site condition in approved pattern includingsurface preparation, pasting of laminate with approved adhesive & finishing it evenlyto make a flat surface without bubble etc. complete. The rates shall include the costof cut outs in the surface as required. All complete as per detail drawing, asspecified and as directed by Architect / Consultant / Project - in - Charge. (Actualexecuted area will be measured).

290.00 SQM

11 Fully glazed partition Providing and fixing in position 12 mm thick Toughened ClearGlass in partition panels by using various glass fittings of approved make (DORMA /HAFELE) to be fixed with necessary supports on the ceiling duly finished withoutgiving any load on the false ceiling by using necessary hardware of Dorma / Hafelemake what ever necessary and required numbers to complete the job in all respect.Contractor is advised to submit working drawing with details of approved makepatch fitting, sizes of glass panels etc and take approvals of consultants beforeexecution of works. All complete as per detail drawing, as specified and as directedby Architect / Consultant / Project - in - Charge. (Actual executed area will bemeasured). Aluminium frame shall be paid separately. Glazed door in partition,

fittings in door such as handle, door closure, floor spring, hinges shall be paidseparately.

182 SQM

12 Full height storage Provision and fixing in position 450 mm wide Full Height Storagecomprising of 12 mm thick approved marine ply as shelves, 6 mm thick approvedmarine ply for back, 12 mm thick approved marine ply for shutter, 4 mm thickapproved Veneer to all external surfaces, 1 mm thick approved laminate to internalsurfaces of shutter including necessary hardware, approved fittings & fixtures likeapproved SS hinges, SS approved handle, approved locks (Godrej or equivalentmake), approved adhesive, melamine polish to all exposed surfaces, etc. allcomplete as per detail drawing, as specified and as directed by Architect /Consultant / Project - in - Charge. (Actual executed area of front elevation will bemeasured).

118.00 SQM

Detailed specification as followsi) Verticals - 19 mm thick marine ply finished with French Polish for all in sidesurfaces.

ii) Skirting ledge and soffit ledge - 19 mm plywood with necessary wooden beadingsetc.


4/19

iii) Shutters - Made out of 12 mm plywood along with 12 mm stiffining ply all aroundthe shutter for at least a width of 100 mm and finished with the 4mm thick Veneerfinish outside & 1 mm thick laminate of approved shade, make, texture & quality oninner side. Site modification as per requirement has to be undertaken with out anyextra cost. The shutters to be provided with locks. The veneer area will be dulymelamine polished. 6mm thick polished wooden lippings to be provided on allexposed ply surfaces and be finished with melamine polish on all the exposed

edges.

iv) Hardware - All necessary hardware such as SS hinges, SS tower bolts, Magneticcatches etc. Hardware shall be heavy duty brass oxidized type, brass body lock(Godrej or equivalent make with extra large group key),

All exposed woodwork to be Melamine polished, all internal surfaces to be finishedwith French polish complete as per drawing and directions. The external surface tobe finished with Veneer basic Rate of Rs 2500/- per Sqm

13 Low height storage unit Providing and Fixing in position Low Height Storage Unit ofheight 1250mm and width 450mm comprising of 19 mm thick approved marine ply,6 mm thick approved marine ply for back, 12mm thick approved marine ply forshutter with shelves as per design of 12mm thick approved marine ply. Shutter

Finished with 4 mm thick approved Veneer with polycoating to all external surfaces,1 mm thick approved laminate to internal surfaces. Including necessary hardware,approved fittings & fixtures like SS hinges, approved handle, approved locks (Godrajor equivalent make), approved adhesice, all drawer shall be of Hettich or approvedequivalent make, melamine polich to all exposed surfaces if required etc. Allcomplete as per detail drawing, as specified and as directed by Architect /Consultant / Project - in - Charge. (Actual executed area of front elevation will bemeasured). Basic Rate of Veneer Rs 2500/- per Sqm. Basic Rate of Laminate Rs800/- per Sqm.

110 SQM

14 Trap Door Providing trap door in 19 mm ply wood finished with 1 mm thick laminateon both sides. The item to include SS hinges, handles if any as per design. The itemalso include providing necessary support structure from the ceiling for fixing the trapdoor shutters.Basic cost of laminate Rs. 800/- per SQM

62 SQM

15 FULLY GLAZED DOOR Providing and fixing in position 12 mm thick ToughenedClear Glass door by using various glass patch fittings of M/S DORMA to be fixedwith necessary fittings on the ceiling duly finished without giving any load on thefalse ceiling by using necessary hardware of Dorma make ever necessary andrequired numbers to complete the job in all respect. Rate to include cost ofhardware such as patch fitting lock .Aluminium frame, door fittings such as floorspring, door closure, hinge, handle shall be paid separately. Contractor shallsubmit working drawing with details of approved make patch fitting, sizes of glasspanels etc and take approvals of consultants before execution of works. Allcomplete as per detail drawing, as specified and as directed by Architect /Consultant / Project - in - Charge. (Actual executed area will be measured).

36.00 SQM

16 PARTLY GLAZED PARTLY SOLID DOOR Providing & fixing 32mm thick Partlyglazed Partly Solid Door with 4mm thick veneer on both sides with melamine polishas per design pattern shown in drawing. All edges should finish with matching wood

lipping with melamine polish. Rate to include 10 mm thick glass Acid etched ,designed opening with wooden beadings finished with melamine polish whereverinstructed, providing necessary hardware, approved adhesive etc. all complete asper detail drawing, as specified and as directed by Architect / Consultant / Project -in - Charge. (Actual executed area will be measured). Basic Rate of Veneer Rs2763/- per Sqm.Frame, Door fittings such as door closure,floor springs, hinges,handles shall be paid separately.

64.26 SQM


5/19

17 Flush door one side veneer one side laminate Providing and fixing 32mm thickFlush door finished with 4mm thick veneer & melamine polish on one side and 1.0mm thick laminate on other side as per design pattern shown in drawing. All edgesshall be finished with matching wood lipping with melamine polish. Rate to includecost of necessary hardware, approved adhesive. All complete as per detail drawing,as specified and as directed by Architect / Consultant / Project - in - Charge. (Actualexecuted area will be measured) Basic Rate of Veneer Rs 2763/- per Sqm. Basic

Rate of Laminate Rs 800/- per Sqm.Frame, Door fittings such as door closure,floorsprings, hinges, handles shall be paid separately.

45.36 SQM

18 Flush door both side veneer Providing and fixing 32mm thick Flush Solid Doorfinished with 4mm thick veneer on both sides with melamine polish as per designpattern shown in drawing. All edges shall be finished with matching wood lippingwith melamine polish. Rate to include cost of necessary hardware, approvedadhesive. All complete as per detail drawing, as specified and as directed byArchitect / Consultant / Project - in - Charge. (Actual executed area will bemeasured). Basic Rate of Veneer Rs 2763/- per Sqm. Frame, Door fittings such asdoor closure,flor springs, hinges, handles shall be paid separately.

68.00 SQMNote: - All hardwares except that of hinges, floor spring/door closure and handlerequired for door shall be included in the quoted rates for door. The above

hardwares will be paid separately under different item specified in Job Schedule.19 Door frame 75mmx50mm Providing and fixing 1st class T.W. Door frame of finished

size 75mmX50mm applicable as per profile shown in the drawing and finished withapproved Veneer and melamine polish and holdfasts/screws as per details.Measurement of the frame will be taken along the center line of frame. All completeas per detail drawing, as specified and as directed by Architect / Consultant / Project- in - Charge. (Actual executed area will be measured). Basic Rate of Veneer Rs2763/- per Sqm. Measurement of frame shall be taken along the center line offrame. 17 CUM

20 Door frame 125mmx50mm ITEM SAME AS ABOVE BUT FOR BRICK WALLS OFFINISHED SIZE - 125 MM X 50 MM WITH HOLD FASTS OF APPROVED SIZE.

2.50 CUM

21 SOFT BOARD Providing and fixing Soft Board panel of specified sizes having 12mm thick soft board covered with felt fabric of approved make and shade of

premium quality and cost of fabric not less than Rs. 1200/- per RM. The board shallhave teakwood / cedar / beech / matching wooden beading, lipping all round. Theboard shall be fixed on prepared surface with necessary hardware fittings etc.complete. All concealed wood works shall have sealer polish as directed. Ratequoted shall be for the complete finished work including all the materials and labourmentioned above. All complete as per detail drawing, as specified and as directedby Architect / Consultant / Project - in - Charge. (Actual executed area will bemeasured). Basic Rate of Fabric Rs 1200/- per Rmt.

49.00 SQM22 White Board Providing and fixing matt finish "white mark/approve equivalent writing

board with enamelled sheet steel front, GI back over approved inner core", ofspecified size black of chocolate colour anodized aluminium beading to form thescreen including the necessary accessories such as magnetic symbols, magneticletters, magnetic strips, magnetic eraser, magnetic bry marker 4 Nos., spare felt for

eraser, board fixing clips etc. and the board shall be made out of enamelled sheetwith backing of AC sheet to suitable thickness etc. complete and all as permanufacturer's specification and as directed by the EIC / Architect. Rate shallinclusive of making and fixing wooden ledge for full length of the board for keepingmarker pen, eraser etc. Rate quoted shall be for the complete finished workincluding ledge board to keep accessories, and all materials and labour mentionedabove. All complete as per detail drawing, as specified and as directed by Architect /Consultant / Project - in - Charge. (Actual executed area will be measured).

18.00 NOS


6/19

23 Providing and fixing in position T.W. Moulding of size 15 mm x 15 mm sizecomplete as per profile given in the detail drawing or as explained out of woodensections of sizes given below. All should be finished with melamine polish ofapproved shade & colour with minimum 3 coats. This item will operate only for thosemouldings which are to be fixed independent of any other item as mentioned in theBill of Quantities and not measured under any other item etc. All complete as perdetail drawing, as specified and as directed by Architect / Consultant / Project - in -

Charge. (Actual executed area will be measured). 320 RMT24 SAME AS ABOVE BUT OF SIZE 75 X 25 MM 444.00 RMT

25 SAME AS ABOVE BUT OF SIZE 25 X 50 MM 382.05 RMT

26 Silhouette Blinds Providing and fixing Luxaflex/Vista livolor make Silhouette ShadesBlinds of approved shade as per the following specification:

42.5 SQMThe blind shall be one part blind, one part drapery and shall be made of soft sheerfabric front and back facings, bonded to translucent fabric vanes. Silhouette shadeshall be operated using a continuous cord loop and with the shade lowered, thevanes could be tilted to any position from fully open to closed. With the vanes open,the sheer fabric facings shall soften the outside view and filter the incoming sunlight.With the shading raised, the fabric shall be concealed into the headrail. Allcomponents are to be colour co-ordinate and the specification is as follows.

Headrail : Channel shall measure 81 mm wide and 61 mm deep with a normal wallthickness of 1.0 - 1.2 mm & extruded from 6063 aluminium alloy with powder coatedfinish.

Cord Tendioner / Cartridge Assembly.

The assembly consists of the following components:Cord tensioner: Cord Tensioner Body, Cord Tensioner Cover, Cord TensionerSpring, Cord Tensioner Cradle, Cord Tensioner Spool, Loop Cord.

Cartrige Assembly : Cartridge, Cord Wheel Shaft, Cord Wheel, Cord Wheel Cover,Clutch / Limit Assembly Set.

Clutch / Limit Assy : Made from high engineering grade plastics and consist of thecord pulley and the limit adjustment and levelling screw.

Any assembly consist of the following:Clutch Side : Right or left Specific Headrail End Cap Cord Pulley, Screw, Torsion,Spring, Spring Release.

Limit Side : Right or Left Specific Headrail End Cap, Right or Left Specific BackPlastic Screw, Right or Left Specific Limit Nut, Limit Adjustment screw, Spring,Screw Limit Bracker, Rotator, Right or Left specific Fabric Sensor, Levelling Screw.

27 VENETIAN/VERTICAL BLINDS :Providing and fixing Luxaflex/Vista Livolor makevertical/venetian blinds of approved shade. The blinds to be fixed andcommissioned as per manufactures specification. All complete as per detaildrawing, as specified and as directed by Architect / Consultant / Project - in -Charge. (Actual executed area will be measured) Basic Rate of Vertical/VenetianBlinds Rs 160 per sqft.

460.80 SQM28 Cable Manager Providing and fixing in position MS powder - Coated Cable

Managers of dia. 75 mm for table tops/side unit wherever directed. The itemincludes cutting necessary holes on glass/side unit/table etc for fixing the cablemanager. All complete as per detail drawing, as specified and as directed byArchitect / Consultant / Project - in - Charge.

115 NOS29 SOFFIT VENEER FINISHED 545.00 RMT


7/19

Providing and fixing in position 250mm width Soffit made of 19 mm thick plywoodfinished with approved veneer with melamine polish including 25X25mm thick T.W.wooden frame work/supports & mouldings, grooves finished with melamine polish.All complete as per detail drawing, as specified and as directed by Architect /Consultant / Project - in - Charge. (Actual executed area will be measured). Basicrate of veneer Rs 1692/- per sqm.

30 JAMB LINING (AVG WIDTH 250 MM) 545.00 RMTProviding and fixing in position 250 mm Jamb Lining in 19 mm thick marine plywoodand finished with approved veneer with melamine polish to wooden moulding andexposed edges finish with melamine polish. All complete as per detail drawing, asspecified and as directed by Architect / Consultant / Project - in - Charge. (Actualexecuted area will be measured). VENEER FINISHED (BASIC COST OF VENEERRS 1692/- PER SQM).

31 100 MM HIGH WOODEN SKIRTING 1200.00 RMTProviding and fixing in position 1st quality matching Badam Wood Skirting of 100mmx 15mm size including 3 coats of melamine polish of approved shade. All completeas per detail drawing, as specified and as directed by Architect / Consultant / Project- in - Charge. (Actual executed area will be measured).

32 DUST BIN SS 120 NOSProviding and arranging in position dust bins out of perforated SS Sheets (min Size200mm dia x 400mm Height). All complete as per detail drawing, as specified andas directed by Architect / Consultant / Project - in - Charge.

33 PHENOTHERM INSULATION (50 MM THICK) 2120.00 SQMProviding and Fixing in position 50 mm thick Phenotherm insulation (KP/AL) with inpartitions / doors wherever as shown and as per the site directions. The rate shallinclude covering of aluminium foils as per manufacturer's specifications.

34 MOVABLE PARTITION 24.50 SQMProviding and fixing 'DORMA' approved movable partition wall in canteen made outof Prelaminated boards with 'STYRO FOAM' INSULATION in between and runningof Anodised Aluminium track capable of taking 500 kgs load and fixed to ceiling withnecessary accessories, with multidirectional rolless, pinious, functions, switch andtrack divertess as required all complete as directed by Architect.

35 8mm GLASS IN PARTITION Providing and fixing 8mm thick toughened clear floatglass with etching design as per drawing and fixed to partition as shown in drawingwith necessary polished T.W. beading all complete as directed.(BASIC RATE OFGLASS Rs. 1412 PER SQM).Wooden/Aluminium frame shall be paid separately.

53.00 SQM36 6mm GLASS FOR TABLE TOP 50.00 SQM

Providing and fixing 6mm thick toughened clear float glass for E/F/D GRADE

Officers table top all as per design and drawing and complete in all respects withnecessary bevelling, cutting, fixing steel vacuum suction arrangements as directedby Architect.

37 WALL PAPER 42.00 SQMProviding and fixing Decorative wall paper on to partition / ply finish / wall etc withapproved adhesive as approved over panelling in any shape, length etc. includingpreparing surface for wall paper. (Rate to include wastage due to shape). (BasicCost Rs 2500/- Per Sqm).


8/19

38 PELMET VENEER FINISHED 10.00 SQMProviding and fixing in position pelmet out of 19 mm thick plywood finished withveneer & melamine polish from the front and synthetic enamel paint from inside.Size of the pelmet - 150 mm x 175 mm. All complete as per detail drawing, asspecified and as directed by Architect / Consultant / Project - in - Charge. The modeof measurement will be total width in both the planes multiplied by length. (BasicCost of Veneer Rs 1692/- Per Sqm).

39 PLY WOOD FACIA VENEER FINISHED 240.00 RMTProviding and fixing in position Plywood Facia - 300 mm wide made out of 19 mmthick plywood finished with approved Veneer & 3 Coats of melamine polish. Rateshall include wooden edge moulding on exposed edge of facia with melaminepolish etc. All complete as per detail drawing, as specified and as directed byArchitect / Consultant / Project - in - Charge. (Basic Cost of Veneer Rs 1692/- PerSqm)

40 FLOOR SPRING (DORMA/HAFELE) BTS 75 19 NOSProviding and fixing floor springs Dorma make BTS 75 V with zero degree openfunction or approved equivalent. The floor spring should be with adjustable closingforce and closing speed. Closing action effective form approx 175 degree, with fullhydraulic sequential control and back check. Including cement box, replaceable

standard spindle and SS cover plate. Non handed; also suitable for double actiondoors cover plate material and finish: stainless steel of approved make andspecification etc. All complete as per detail drawing, as specified and as directed byArchitect / Consultant / Project - in - Charge.

41 DOOR CLOSER (DORMA / HAFELE) TS 72 95 NOSProviding and fixing Door Closures, Dorma TS 72EN -2/4 rack & pinion overheaddoor closure suitable for door width max 1100 mm with standard arm or approvedequivalent. All complete as per detail drawing, as specified and as directed byArchitect / Consultant / Project - in - Charge.

42 S.S HANDLES - 600 MM HIGH 152 NOS

Providing SS Handles of size 600 mm high in pairs to doors etc of SS garde 316 asper approved profile of M/S Kitch or approved equivalent.

43 SAME AS ABOVE BUT OF SIZE 200 MM HIGH 28 NOS44 STAINLESS STEEL BALL BEARING HINGES SIZE

100 X 73 X 3 MM380 NOS

Providing and fixing Heavy duty ball bearing hinges of size 3/4" (100 mm x 75 mm x3 mm) suitable for wooden and steel doors with all accessories complete (Cat No.551 BB stainless steel of M/S Dorma or approved equivalent). All complete as perdetail drawing, as specified and as directed by Architect / Consultant / Projcet - in -Charge.

45 DEAD LOCK 95 NOS

Supply and fixing of SS dead locks of Dorma ref no- 778 make / approvedequivalent with standard lock case for europrofile cylinder of required size forminimum 60 mm thick door.

46 ACRYLIC EMULSION PAINT 3100.00 SQMProviding and applying 3 or more coats of superior quality of Acrylic Emulsion Paintof approved make on Ceiling / Partition of approved make and shade and to give aneven shade including preparation of surface, applying primer of approved make etcincluding surface preparation. All complete as per detail drawing, as specified andas directed by Architect / Consultant / Project - in - Charge & manufacturer'sspecifications. Rate to include additional coat of paint if required to get smooth anduniform finish.

47 TEXTURE PAINT ON WALL 240.00 SQM


9/19

Providing and applying Texture Paint including preparing surface, using roller to getapproved texturised surface. Job to include making required surface preparation, toreceive Texture paint finish etc. All complete as per detail drawing, as specified andas directed by Architect / Consultant / Project - in - Charge.

48 LUSTER PAINT 120.00 SQMProviding and applying Luster paint including, using roller to get approved texturised

surface. Job to include making necessary surface preparation to receive paint etc.All complete as per detail drawing, as specified and as directed by Architect /Consultant / Project - in - Charge.

49 SYNETHETIC ENAMEL PAINT 240.00 SQMProviding and applying 3 coats of Synthetic Enamel Paint of approved make quality,shade over one coat of primer and levelling course. Rate to include scrapping wallsurfaces, applying putty for proper finish, applying necessary. Coat or primer to getfirm surface to receive paint. All complete as per detail drawing, as specified asdirected by Architect / Consultant / Project - in - Charge.

50 DUCO PAINT 126.00 SQMProviding and applying in 3 coats lacquer paint of "DUCO" / approved equivalent.Make and shade over metallic surfaces / wooden surfaces after preparing the

surface with water proof putty to get proper surfaces, applying necessary coats ofprimer and finishing with matt / textured finish laquer paint. All complete as per detaildrawing, as specified and as directed by Architect / Consultant / Project - in -Charge.

FALSE CEILING WORK

51 GYPSUM BOARD CEILING 2070.00 SQM

Providing and fixing in position Gypsum Board False Ceiling of India Gypsum /approved equivalent as per manufacturer's specifications and instructions with 12.5mm thick 'Gypboard' Screw-fixed to the underside of suspended G.I. grid. G.I. gridshould be constructed and suspended from the main ceiling as per manufacturer'sinstructions and specifications. G.I. grid should consist of ceiling sections (IndiaGypsum Code No. MF5) at maximum centre to centre distance 450 mm, Perimeterchannel (India Gypsum Code No. MF 6A) intermediate channels (India GypsumCode No. MF7) at maximum centre to centre distance 1200 mm. The ceilingsections should be fixed to intermediate channels with connecting clips (IndiaGypsum Code No. MF9). G.I. grid should be fixed to R.C.C slab above with the helpof 25 mm x 0.5 mm strap hanger (India Gypsum Code No. MF8) and Soffit cleat(India Gypsum Code No. P534). The joints between soffit cleat and strap hangerand G.I. grid and strap hanger should be with 6.4 x 12.7 mm nut and bolt (IndiaGypsum Code No. P526).


10/19

Soffits cleats should be fixed to R.C.C ceiling with w.E. type 12 mm dia, 17/16" longsteel Rawl plug maximum centre to centre distance (both ways) of strap hangersshould be 1200 mm. The Gypboard should be fixed to G.I grid with 25 mm longDrawall screws. The 'Gypboard' to be used should be 12.5 mm thick tapered edgeboards. The boards should be taped and filled from underside to ceiling. Item to becomplete as per manufacturer's specification and instructions. The rate shouldinclude necessary additional ceiling sections and intermediate channels should be

provided at openings for light fixtures, A.C. Ducts, vertical drops, offsets, etc.Additional intermediate channels should be fixed to strap hangers for additionalsupports to prevent strap hangers from buckling/swayng at every 1200 mm. Item tobe complete in all respect including necessary sleeves for ducts finishing of jointscut outs supports for A.C grills, light fixtures, speakers etc. complete as perdirections.

Note: - No extra will be paid for ceiling drops and it will be considered as flat ceilingand if there is projected drop ceiling curved as per design in different level it will alsobe paid as addition to that but only average bottom surface area will be considered.No extra will be paid for light cuttings, cutting for glass or stain glass. No extrachannel will be paid if it is required for additional support.

52 METALLIC FALSE CEILING 290.00 SQMProviding and fixing Luxalon 600X600mm Perforated Aluminium panel of M/S.Hunter Douglass make/Armstrong/Interarch make consisting of panel600X600mmX15.5mm deep x 0.6 mm thick with bevel edge, Coil Coated on aContinuous Paint Line, Double baked and roll formed from enamelled corrosionresistance aluminium alloy AA 3005 (Al. Mg) for higher strength and good rollforming characteristics. The Panels shall about each other with a narrow V grove.Panel shall be clipped to a baked enamelled aluminium Panel carrier of 32 mm widex 39 mm deep x 0.95 mm thick in standard length of 5 mtr made of doubled bakedenamelled aluminium alloy AA 5050 (Al. Mg) black with cut outs to hold carrier shallbe suspended by means of G.I. suspension rod 4 mm diameter and a Galvanisedsuspension spring clip at a distance of 1.7 mtr C/c. Overdeck insulation boards shallbe placed above the panels.

Mode of Measurements :- Measurements shall be wall to wall without anydeductions for lights, diffusers, columns etc.

53 CALCIUM SILICATE BOARD CEILING 714.00 SQM

Providing and fixing Calcium silicate board of 8 mm thick Ramco Hilux/ HyderabadInsulation Ltd make with regular frame of suspended ceiling comprisis of galvanisedsteel perimetre channel of having 55 mm thickness and unequal flanges fixed towalls/partion using nylon sleeves and screws at 450 mm centers. The intermeditechannel (91 mm thick) having two equal flanges of 15 mm each and web of 45 m issuspended from the at 1220 mm wit ceiling angle of width 25 mm x 10 mm x 0.5 mmfixed with cleat and steel expansion fasternes. The calcium silcate board to be fixedalong / acroos the ceiling sections with 25 mm long self driling and tappings screwsat 200 m C/c. The joints to be finished with 48 mm wide fibre tape to provideseamless finish. Additional perimeter channel and suporting materials are to be

provided to make any opening for light fittings, diffusers etc. The frame work to besupported properly to maintain the integrity or ceiling and shall be at no extra cost.Rate shall include joining tape and compound. The item shall be paid any on thefinished surface only and any wastage will be in contractors scope.

54 POP CORNICES / MOULDINGProviding, casting and fixing in position decorative plaster of Paris mouldings ofsizes given below as per drgs and direction from EIC.SIZE 100 X 75 MM

250.00 RMT55 Item same as above SIZE 150 X 75 MM 250.00 RMT


11/19


12/19

Providing and fixing in position Table of approved shape made up of 19 mm thickapproved marine plywood including, Drawer Unit, Filing Storage, Space for CPU,12mm thick marine ply for footrest with veneer finish. 6 mm thick approved marineplywood for rear side of side unit. The Table Top shall be finished with 4mm thicknatural veneer of approved colour, shade, sides apron, front sides finish with naturalveneer and melamine polish. All drawers and trays to be in marine plywood with 19mm in front and 12mm thick in rear and sides and bottom in 6 mm thick. marine

plywood finished with approved veneer to all external surfaces and 1.0 mm thickapproved laminate to all internal surfaces. Drawer unit fronts and sides to befinished with veneer and melamine polish. Edges of table 38 x 25 mm thick woodenmoulding with melamine polish.

All the tables shall have metal key board trays to accommodate keyboards andmouse where ever necessary as per drawings and also shall include C.P.U unit asshown in the drawings. All drawer use Hettich / Haffele approved equivalent slidingchannels and central lock no separate payment shall be made for this. All completeas per detail drawings, as specified and as directed by Architect / Consultant /Project - in - Charg. BASIC RATE OF VENEER RS 2421/- PER SQM, BASIC RATEOF LAMINATE RS 800/- PER SQM

62 Item same as above E GRADE OFFICER SIZE (1800X750X750mm HEIGHT)

11 NOS63 Item same as above F GRADE OFFICER SIZE (2000X900X750mm HEIGHT)

4 NOS64 Item same as above OFFICER GRADE A,B,C & NON MANAGEMENT STAFF

TABLE 80 NOSProviding and fixing table of size 1500mmX600mmX750mm height of shape asshown in drawing made up of 19mm thick marine grade plywood including Keyboard tray, pencil tray, space for CPU.

Table Top and sides made up of 19mm thick marine grade ply finished with 1.0mmthick laminate of approved shade and make and footrest with 12mm thick marinegrade ply finished with laminate as shown in drawing complete in all respects.

Key board trays to accommodate key boards where ever necessary as per drawingwith Hettich/Haffele approved equivalent sliding channels, stoppers, No separatepayment shall be made for this.

Two nos. of Pencil tray made up of 19mm thick marine grade ply wood on all sidesand finished with exterior grade 1.0mm thick laminate on the outside and internalcomplete with Haffele approved sliding channels. Size of tray(500mmX350mmX100mm) . BASIC RATE OF LAMINATE - Rs. 800/- PER SQM

65 "D" GRADE OFFICER TABLE 14 EACHProviding and fixing table of size 1550mmX750mmX750mm height of shape asshown in drawing made up of 19mm thick marine grade plywood including Keyboard tray, pencil tray, space for CPU.

66 GM's TABLE 1 EACHProvision and fixing table of size 1840X900mm (avg)X750mm height with a side unit

attached to the table as per approved design and drawing with necessary hollowstainless steel pipe framework. Table made up of 19mm thick marine plywood on allsides finished with 4.0mm thick natural veneer of approved shade with melaminepolish as directed by Architect/Project-in-charge. Table top made of bevelled edge10mm thick clear glass with necessary chromium plated stainless steel fixingmanets.


13/19

Attached side uint of size 800X450X1200mm height as per design made up of19mm thick marine ply veneer finish with melamine polish and 8mm thick frostedglass on top complete with necessary hardware, etc. in all respects.

One complete drawer unit as per design of size 460X400X750mm height made of19mm thick marine plywood laminate finish (exterior grade) with Haffele approvedslilding channels, stopprs, central lock etc. complete in all respects.

BASIS RATE OF VENEER Rs. 1050/- PER SQM

BASIS RATE OF LAMINATE Rs. 800/- PER SQM

67 DGM's TABLE 3 EACH

Same as above

68 SIDE UNITS OF ALL OFFICER GRADE 59 EACH

Providing and fixing side units made of 19mm marine grade plywood with exteriorgrade laminate (1.0m) finish of approved shade complete with 12mm thick shelvesfinished with exterior grade 1.0mm thick laminate with necessary polished teakwood lipping and back made of 6mm thick marine plywood laminate finish all as perdrawing including 50mm high skirting plate of polished wood.

SIZE - 1200X450X700 mm HEIGHT

Sliding shutters made up of 19mm thick marine grade plywood finished with exterior

grade matching and approved shade laminate of 1.0mm thickness with polishedteak wood lipping, with necessary PVC sliding channel, brass tower bolt, chromiumplated handles, rollers etc. complete in all respect.

5 Nos. Pencil trays made of 19mm thick marine plywood of size 300X450X120mmheight with Haffele approved sliding channel, stoppers finished with exterior grade1.0mm thick laminate of approved shade all as per drawing and as per instruction ofArchitect.

69 SIDE UNIT OF NON-MANAGEMT STAFF 50 EACH

Providing and fixing side unit made of 19mm marine grade plywood on all sides andtop and 6mm thick plywood for back finished with 1.0mm thick exterior gradelaminate of approved shade all as per drawing complete with drawers, open shelvesmade up of 19mm thick MR grade plywood necessary Haffele approved drawersliding channels, central lock keys and finished with exterior grade 1.0mm thicklaminates all as directed by the Architect including skirting plate of polished solidwood 60mm high.

SIZE 900mmX450mm WIDE X750mm HEIGHT

DRAWER SIZE 400mmX450mm DEEP.

BASIS RATE OF LAMINATE Rs. 800/- PER SQM

70 SIDE UNIT FOR GM AND DGM 4 EACH

Providing and fixing side unit made of 19mm thick MR grade plywood on all sidesand top and 6mm thick plywood for back side with drawer units, shelves coveredwith sliding shutters made out of 19mm thick MR grade plywood finished withnatural veneer of approved shade complete as per drawing and as directed by theArchitect with all necessary Haffele approved sliding channels, stoppers, centrallock, keys, handles, tower bolts etc.and 50mm high wooden skirting polished as

desired.

SIZE 1880mmX450mmX750mm HEIGHT.

BASIS RATE OF VENEER Rs. 1950/- PER SQM


14/19

71 Providing and fixing back side console made of 19mm thick MR grade plywood onall sides and top and 6mm thick plywood for backside complete with natural veneerfinish for outside and 1.0mm thick exterior grade laminate finish for drawers,shelves, shutters. All drawers and shutters to have Haffele approved slidingchannels, stoppers, stainless steel matt finish handles, central lock, keys, magneticstoppers, brass oxidised hinges, teak wood lipping polished for edges all completeas per drawing and shades approved as per Architect's direction. (BASIC RATE OF

VENEER Rs. 1050/- PER SQM) (BASIC RATE OF LAMINATE Rs. 800/- PER SQM)SIZE 1800mmX450mmX700mm HEIGHT95 EACH

72 Same as above SIZE 2500mmX450mmX700mm HEIGHT

14 EACH73 same as above SIZE 2970mmX450mmX700mm HEIGHT

1 EACH74 RECEPTION TABLE

Providing and fixing reception table made up of 19mm thick marine grade plywoodfinished with approved natural veneer (4.0mm thick) as per drawing complete withnecessary hollow stainless steel pipe framework, 8mm thick toughened clear glasstable top supported on stainless steel manets, drawers on Haffele approved slidingchannels, central lock, keys etc and shelves finished with approved shade of 1.0mmthick exterior grade laminate, edge lipping with polished teak wood all as directed by

Architect / Project - in - charge.(BASIC RATE OF VENEER Rs. 2000/- PER SQM),(BASIC RATE OF LAMINATE Rs. 800/- PER SQM) . SIZE2100mm(L)X750mm(W)X750mm(H)

1 EACH75 Supply of sofa with stainless steel pipe frame, cushion Arms, PU leatherite

Tapestrey of approved shade as directed by Architect.SIZE1475mm(L)X760mm(D)X860mm(H)

25 EACH76 Sofa of SIZE 750mm(L)X750mm(D)X675mm(H) with same specification

16 EACH77 Providing and fixing mail Room Pigeon hole letter storage cabinet all as per drawing

complete with 19mm thick MR grade plywood with 1.0mm thick exterior gradelaminate finish and boxes of 150X150mm and 200mm deep.

6 SQM

ARTEFACTSProviding and fixing Murals / Pictures of approved design and make as per directionfrom EIC. The design / picture will be approved from any renowned agency/painterin Hyderabad / Mumbai for the following basic rate.

78 PICTURE/PAINTING WITH BASIC RATE RS 35000 5 NOS79 PICTURE/PAINTING WITH BASIC RATE RS 20000 20 NOS80 PICTURE/PAINTING WITH BASIC RATE RS 5000 15 NOS

FRP PLANTERS-Providing and arranging in position FPR planters of following sizes as per approveddesign with heavy gauge.

81 FRP planters of size - 350mm dia. 40 NOS

82 FRP planters of size 225mm X 225mm X 200mm ht. 40 NOS83 Brass planters 10 NOS

Providing lacquered brass planters of size 300mm approved shape and make.

84 WOODEN PLANTER: 20 NOSProviding 305 x 305 x 400 mm size of wooden planters made out of 18 mm thick.Marine ply cladded with veneer of approved veins & best quality Teak wood lipping& molding, polished in melamine finish ext. & French polish int.

ARTIFICIAL PLANTS:


15/19

Providing and arranging artificial plants like creepers, leaves etc or flowerarrangment. Including the pots with marble / stone pebbles, moss etc. as perapproval and section.

85 Artificial Medium bushes & Creepers up to 400 mm HT. 40 NOS

86 Artificial SMALL Plants arrangments up to 1100 mm HT. 40 NOS

87 Artificial BIG Plants arrangment up to 1500 mm HT. 20 NOS

CIVIL WORK88 125MM THICK BRICK WALL 180.00 SQM

Providing 115mm nominal thickness Brick Masonry with locally available bestquality bricks of compressive strength of minimum 75 Kg/sqcm in cement mortar1:4 in half brick thick wall including RCC bands of 100mm height with longitudinalsteel reinforcement of 2 no 8 mm dia bars constructed at every 1.0m height of thewall including scaffoldings, racking cut joints and watering complete. Rate should beapplicable for all heights etc. All complete as per detail drawing, as specified and asdirected by Architect / Consultant / Project - in - Charge.

89 15 MM THICK PLASTER 415.00 SQM

Providing internal cement plaster of average 15mm thick in a single coat in cementmortar 1:4 without neeru finish to concrete or brick surfaces in all positions includingscaffolding, curing, complete etc. All complete as per detail drawing, as specifiedand as directed by Architect / Consultant / Project - in - Charge.

FLOORING AND DADO

NOTE for flooring and Dado Work:

All granite and marble flooring and dado sizes will be based on the site dimensions.

All ceramic / glazed tiles flooring / dados shall be done on tile module.

Actually executed quatity will be measured and no consideration shall be given forwastage and difference of method of measurement between market/supplier's

method and site method.

The rate shall include laying the tiles / marble / granite / ceramic tiles / stone slabs toany pattern as specified and shown on drawings & no extra cost shall be paid forwastage of materials.

The rate shall also include cost of cutting tiles for fixing electrical boxes & switches,water-taps, nahani traps, plumbing accessories etc. for which no extra paymentshall be made.

90 ITALIAN MARBLE FLOORING 312.40 SQM

Providing and fixing Italian marble Slabs for flooring of uniform colour with 18 mmthick + 2mm tolerance machine cut, machine polished in nominal sizes, as perdrawing & pattern including average 25mm thick cement, sand mortar bedding (1:4)close jointed & floated with matching cement slurry laid to level as required, curingcomplete as per specification, machine polished cleaned complete. No extra will bepayable towards wastage due to material pattern. Please note that payment will bein SQM of finished floor area only. Rate to be applicable for all levels & heights. Noextra is payable for additional thickness of bedding to match adjoining floors, as perdirections of Engineer-in-charge. The item includes complete finishing of the flooringwith tin oxide polishing. Basic rate Rs 6000/- per sqm.

91 ITALIAN MARBLE SKIRTING 60.00 SQM


16/19

Providing and fixing in position 100mm high approved Italian Marble 18mm thick inapproved colour and shade for Skirting in approved pattern to true line and level ,fixing with neat cement paste, filling the joints with white / colour cement includingedge moulding, edge polishing, cleaning, watering, curing etc. All complete as perdetail drawing, as specified and as directed by Architect / Consultant / Project - In -Charge. (Basic rate Rs 6000/- per sqm).

92 ITALIAN MARBLE DADO 124.00 SQMProviding and fixing approved Italian marble slab dado of uniform colour with 18mmthick (+ 2mm tolerance) machine cut, machine polished in nominal sizes, as perdrawing & pattern including 12mm backing plaster with 1:3 CM and thereafter fixingmarble by using adhesive in cement paste as per the manufacturers specification.(Including back up blushes). The dado substrate should be smooth in plumb andline level. All as per manufacturer's specifications & instructions of Engineer - In -Charge. (Only plan / elevational area wil l be measured. Wastage due to dimensionaldifference, pattern, and cutting sizes available will be to the contractors account).Rate to include all holes & openings, required for fixtures and fittings. Necessaryprovision shall be made in the lift lobby cladding for providing the forste glass andelectrical points. (BASIC RATE OF ITALIAN MARBLE SLAB RS 6000/- per sqm)

93FLAMED FINISHED GRANITE FLOORING 214.00 SQMProviding and fixing flame finished Granite Slabs for flooring of approved pattern ofuniform colour with 18mm thick + 2mm tolerance machine cut, machine polished innominal sizes, as per drawing & pattern including average 25mm thick cement, sandmortar bedding (1:4) close jointed & floated with matching cement slurry laid to levelas required, curing complete as per specification, machine polished cleanedcomplete. Rate to include cost of design patterns in combination of two or threedifferent colour as per drg. and tin oxide polishing to provide mirror polish. No extrawill be payable towards wastage due to material pattern. Please note payment willbe in SQM of finished floor area only. Rate to be applicable for all levels & heights.No extra is payable for additional thickness of bedding to match adjointing floors, asper directions of Engineer-in-Charge. (Basic rate granite slab Rs 2500/- per sqm)

94 FLAMED FINISHED GRANITE SKIRTING 20.00 SQMProviding and fixing in position 100 mm high approved flame finish granite 18mmthick of approved colour and shade for Skirting in approved pattern to true line andlevel on average 12mm thick backing coat plaster in 1:4 mix cement sand mortar,1:1 cement grout filling the joints with white/colour cement including edge moulding,edge poilshing cleaning, watering, curing etc. All complete as per detail drawing, asspecified and as directed by Architect / Consultant / Project - In - Charge. (Basicrate granite slab Rs 2500 per sqm). The granite band for certain items coverd in thedrgs will be paid under this item.

95 GRANITE DADO 32.00 SQMProviding and fixing approved Granite slab dado/cladding of uniform colour with18mm thick (-/+ 2mm tolerance) machine cut, machine polished in nominal sizes, asper drawing & pattern including 12mm thick backing plaster 1:3 and thereafter fixingmarble by using adhesive in cement paste as per the manufacturers specifications.

(Including back up blushes). The dado substrate should be smooth, in plum and linelevel. All as per manufacturer's specifications & instructions of Engineer-in-charge.(Only plan/elevational area will be measured. Wastage due to dimensionaldifference, pattern, and cutting sizes available will be to the contractors account).Rate to include all holes & openings required for fixture and fittings. Necessaryprovision shall be made in the lift lobby cladding for providing the frosted glass andelectrical points. Basic rate 2500 per sqm.


17/19

96 Providing and laying Vitrified tiles in floor of approved make, color and shade andof uniform thickness not less than 10mm laid over cement sand bed mortar (1:5)not more than 30mm thickness , use of edge clips for proper aligement , laying thetiles on neat cement slurry and filling the joints with white cement mixed withmatching colourcomplete in all respects as per instruction of Architect/Project-in-charge.SIZE OF TILE- 800MM X 800MM.Basic rate :Rs120/- per sqft

880.00

SQM

97 Item same as above but with TILE SIZE - 600MM X 600MM.Basic rate:Rs. 105/-persqft 1600.00

SQM

98 Providing and laying Vitrified tile skirting of matching color and approved make andshade fixing tile with neat cement paste etc. complete as per technical specificationsand as instructed by Architect / Project-in-charge complete in all respects.

60.00 SQM

99 WOODEN FLOORING 64.00 SQMProviding and fixing 9mm thick Laminated wooden flooring (AC-5) of plank size 200mm x 1200 mm / approved size of Pergo/Armstrong/Berry/Euro make , providing2mm thick foam as per manufacturers specification, dock Itounge & groove jointand providing and fixing skirting board beading to match the flooring. The item shallalso include providing door profiles wherever required. All complete as per detaildrawing, as specified and as directed by Architect / Consultant / Project - in -Charge. The item include supply and fixing of skirting profile and door profile to the

flooring and no extra will be paid for this. (Basic rate Rs 4500/- Per Sqm).

100 CERAMIC TILE FLOORING 122.00 SQMProviding and laying Nonskid Matt Glazed Ceramic Tiles (300mm X 300mm X7mm) thick or size as approved of approved make and shade in floors includingproviding 20mm thick 1:5 cement mortar bedding, laying the tiles on neat cementslurry and filling the joints with white cement mixed with matching colour .Basicrate Rs. 45/- per sqft

101 CERAMIC TILE DADO 26.00 SQMProviding and laying Glazed Ceramic Tiles (300mm X 200mm X 6.5mm thick) ofapproved make and shade in dados laid over 10mm thick plaster with cementmortar 1:3, fixing the tiles with neat cement paste, filling the joints with white cementmixed with matching colour.Basic rate Rs. 55/- per sqft.

102 ATRIUM RAILINGSupply and installation of satin finish stainless steel AISI 304 handrail andbalustrade system having 38mm dia SS tube handrail (1.5mm wall thichness)connected with unified stem keys in bead blasted finish to 12X54mm satin finish flatvertical stainless steel member weight 7kg per piece erected with chemical grout tobe fixed on the top of the floor (spigot fixed) at C/c distance as shown in drawinghaving infill of 10mm thick toughened glass complete with necessary bends andterminations and set of accessories of weight 5kg. Height of handrail shall be1000mm from the top of floor finish.Vertical member (Uprights ) will be paidseparately.

26.00 RMT

103 Vertical members (uprights) Supply and installation of stainless steel verticalmember 12x54mm SS flat weight 7kg per piece erected with chemical gront to befixed on the top of the floor (spigot fixed) at C/c distance as shown in drawing and

height shall be 1000mm.

26 NOS.


18/19

INTERNAL ELECTRIFICATION

104 POINT WIRING FOR LIGHT/FAN Supplying, Installation, Testing andCommissioning of point wiring for light/call bell/exhaust fan points with 2 x1.5sq.mm. 1100V grade PVC insulated colour coded stranded copper conductorFRLS wires made to IS:694 and continuous 1.5 sq.mm .copper conductor greencolored PVC insulated earth wire to run inside heavy gauge PVC conduit of suitablesize ,from switch Board to point via controlling switch ,including PVC conduits &

accessories like couplers, Elbows, Junction boxes etc. above false ceiling and inconcealed manner on wall/partition including supply and fixing 6A modular typeswitch , switch board , concealed metal box including required numbers of BlankSwitch for closing the extra module. Circuit wiring from MCB DB to switch boardshall be paid separately. One point controlled by one No.6 Amp switch

34 Points

105 Item same as above but Two points controlled by one No. 6 Amp switch 200 Points

106 Item same as above but Three points controlled by one No. 6 Amp switch 400 Points

107 Item same as above but Four points controlled by one No. 6 Amp switch 6 Points

108 Call bell buzzer Supply and installation of Call bell buzzer with indicator & 4nos.bell

push switches below table in conference room.

8 Each

109 Exhaust fan Point : Providing exhaust fan point controlled by one no 6A switch and6A 5 pin socket near exhaust fan including providing wiring 2x1.5sqmm from switchboard to exhaust fan point ,supply of switch and plug.

12 Points

110 PVC Conduit 25mm dia Supply and installation of 25mm dia PVC conduit ofapproved make clamped to wall/ceiling and inside partition for LAN cable andTelephone wiring.

400 RMT

111 Circuit wiring Supply & laying of PVC insulated copper wire FRLS drawn in heavygauge PVC conduits from MCB DB to switch boards (lighting/power sockets)including conduits & all required accessories.Circuit wiring with One no. circuit of 2x2.5 +1.5sq mm wire in 20mm conduits.

650 RMT

112 Circuit wiring with Two no. circuit of 2 x2.5 +1.5sq mm wire in 25mm conduits. 1800 RMT

113 Circuit wiring with one no. circuit of 2 x4.0 +1.5sq mm wire in 25mm conduits. 300 RMT

114 Circuit wiring with Two no. circuit of 2 x4.0 +2.5sq mm wire in 25mm conduits 300 RMT

115 Circuit wiring with one no. circuit of 2 x6.0 +4sq wire through 25mm conduit. 250 RMT

116 Circuit wiring with Two no. circuit of 2 x4.0 +2.5sq mm wire drawn in under floorraceways.

1750 RMT

117 6A switch 6A 5pin socket Supply & Installation of 6Amp single switch socketuniversal type along with plate with G.I.box recessed on partition /wall.

20 Each

118 16A switch 6/16A socket .Supply & Installation of 6/16Amp single switch socketuniversal type outlet along with plate with G.I.box recessed on partition /wall.

20 Each

119 Work station points Supply ,Installation of group of plug points and switches forcomputer with modular type 5 pin 6 Amp sockets 3 nos, 6A modular switches 3nos , 6/16 A modular socket 1 no, 16A modular switch 1 no to be provided inpartition with indicator and with switch board and PVC box recessed (concealed)on partition wall above side units .

200 Each


19/19

120 20 A industrial socket Supply & Installation of Industrial type socket outlet with plugtop & 20A SP MCB, metal box recessed on partition/wall.

6 Each

121 Supply & Installion of light fixtures completely wired with chokes, roller lock typeholder, Lamps/ fluorescent tubes and chain supports from ceiling wherevernecessary.LED STRIP LIGHT Recessed type LED light. Cat. ref. WW929000301905 of Philips or equivalent make.

48 Each

122 DOWN LIGHT 2 x 26 W Recessed type down light with 2 x 26 Watts PL, Cat. ref.FBH 225/226HF TURBO with 26W PLC of Philips or equivalent make

256 Each

123 GENERAL LIGHT 2 x 36 W Recessed twin Tube T5 lighter with 2 x 36 watts T5, cat.Ref. TBS 369/236 M2 HF with electronic ballast of Philips or equivalent makes.

33 Each

124 PL LIGHT 2 x 36 W Recessed twin Tube PL lighter with 2 x 36 watts PL, cat. Ref.FBS 470/236 HF D6 with PL L 36W and electronic ballast of Philips or equivalentmakes.

66 Each

125 SPOT LIGHT 1 x 54W Surface mounted cat.ref. ILF2FW-2-54T5HO-U4-230V-50Wof Lithonia or equivalent make

6 Each

126 TUBE LIGHT 1 x 28W Surface mounted with 1 x 28 watts FTL, cat. Ref. TMS099/128 Yellow Light with electronic ballast of Philips or equivalent make

150 Each

127 DOWN LIGHT 1 x 18 W Recessed type down light with 1 x 18 Watts PL, Cat. ref.FBS 095/118 with 18W PLC of Philips or equivalent make

60 Each

128 Exhaust fans Providing and fixing of heavy duty Exhaust fans of window mountedtype with screen & louvered shutters- 9inch dia of approved make and colour

12 Each

129 Chandelier Providing & fixing chandelier type light fixture of approved design ofapproved make including lamp.(Basic rate Rs 20000)

1 Each

130 Supply and installation of under floor raceways & accessories including floor cutting,chiseling and necessary Civil work as per approval of Architect/ Consultant.136mmwide, 38 mm deep single Compartment, 16 SWG, Aluminium extruded section forunder floor raceways(rectangular shape).

350 RMT

131 Supply and installation, of under floor raceways & accessories including floorcutting, chiseling and necessary Civil work as per approval of Architect/Consultant200mm x 200mm x 42mm, 14 SWG G.I. Junction BOX with G.I. cover.

85 Each

132 Spike guards with 6 AMP sockets x 4 Nos. with 16 AMP common switches withindicator lamp for cabin area

30 Each

Documents

Office Tender