Nureva™ interactive panoramic projector

User manual

11

ContentsInput/output connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Projector on-screen display menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Picture 5Screen 7Settings 8Volume 9Options 10Interactive 11Network 11

Touch module on-screen display menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Configuration 12Settings 13Information 14

Multimedia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Mobile display 15Laptop display 16Desktop display 16USB storage display 17Configuringmultimediadisplaysettings 17

RS232 commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Commands set list 19

Crestron® room control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Web browser projector control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Projectorinformation 22LANsetting 23Wi-Fi 23Projectorstatusandcontrol 24Emailalert 25Passwordsetting 25

Video compatibility modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26VGAanalog 26VGAanalogcontinued 27HDMIdigital 28HDMIdigitalcontinued 29

Installing and cleaning the dust filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Regulation and safety notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

2

Input/output connections

Control panel

1.  On/standby LED: Refer to the LED indicator of the projector power status

2.  Enter: Confirmyouritemselection

3.  Temp LED: Refer to the LED indicator of the projector temperature status

4.  SSI LED: Refer to the LED indicator of the projector light source status

5.  Menu: Launch the on-screen display menu. To exit the OSD, press the menu button again.

6.  Input: Select an input signal

7.  Four directional select keys: Use the arrows to select items or make adjustments to your selections

8.  Power: Turntheprojectoronoroff

Whenever possible, use the buttons on the projector remote control instead of the control panel as this will help prevent shifting or skewing the projected image.

1 2 3 4

5

68

7

3

Remote control

1.  Input source: Select the input source

2.  Menu: Launch the on-screen display menu. To exit the OSD, press the cancel button or the menu button again.

3.  Power:Turntheprojectoronoroff

4.  Four directional select keys: Select items or make adjustments to your selections

5.  Cancel: Exit a menu or cancel a selection

6.  Volume: Adjust the volume level for the projector’s speaker

7.  Mute: Mute the sound from the projector’s speaker

8.  Calibrate: Manually calibrate touch. After pressing the button on the remote control, press and hold the crosshair symbol that appears on the screen untilitchangestoadarkercolor.Liftyourfingerand follow the dot to the next location. Repeat this step until the calibration process is complete.

9.  Enter: Confirmyouritemselection

4

Projector on-screen display menu The projector has multilingual OSD menus that allow you to make image adjustments and change a variety of settings.

To access the OSD, press the menu button on the projector remote control or control panel.

Use the arrow buttons on the projector remote or control panel to navigate the main menu on the left-hand side. Press the enter button or the right arrow key to enter a submenu.

Use the up and down arrow keys to select the desired item in the submenu and the left and right arrow keys to adjust the settings.

Once you have completed the necessary adjustments in the submenu, press the menu button again to return to the menu.

To exit the OSD, press the menu button again or cancel. The new settings will automatically be saved.

Navigating the menu

Menu

Submenu Settings

5

Picture

Color modeChoose from the factory pre-set options or set your own custom color mode:

• Bright – for brightness optimization• PC – For meeting presentation • Movie – For playing video content• Game – For game content• Blending – Color matching for dual displays• User – Custom user settings

Wall colorOptimize the screen image according to your wall color. Choose from white, light yellow, light blue, pink and dark green.

BrightnessUse the left and right arrows to adjust the brightness of the image.

ContrastAdjustthecontrasttocontrolthedifferencebetween the lightest and darkest parts of the picture.

Sharpness – video mode onlyUse the left and right arrows to adjust the sharpness of the image.

Saturation – video mode onlyAdjust the image from fully saturated color to black and white using the left and right arrows.

Hue – video mode onlyAdjust the color balance of red and green:

• Press the left arrow to increase the amount of green in the image

• Press the right arrow to increase the amount of red in the image

GammaAdjust the gamma value to obtain better image contrast for the input.

Color tempAdjust the white balance in 300K increments.

6

ColorChoose which color to adjust on the screen (Red, Green, Blue, Cyan, Magenta or Yellow).

HueAdjust the RGB levels of the selected color using the left and right arrows.

SaturationAdjust the intensity of the selected color using the left and right arrows.

GainAdjust the brightness of the selected color using the left and right arrows.

Color settings

The color settings are sensitive and easy to unbalance. Adjust the picture settings before considering these adjustments.

7

Screen

Aspect ratio Auto – Keep the image’s original width-height ratio andmaximizetheimagetofitnativehorizontalorvertical pixels

4:3 – Theimagewillbescaledtofitthescreenanddisplayed using a 4:3 ratio

16:9 –Theimagewillbescaledtofitthewidthofthescreen and the height adjusted to display the image using a 16:9 ratio

16:10 – Theimagewillbescaledtofitthewidthofthe screen and height adjusted to display the image using a 16:10 ratio (only for SSI 1080p)

UWHD – Theimagewillbescaledtofitthewidthofthe screen and the height adjusted to display the image using a 16:6 ratio (only for ultrawide)

PhaseSynchronize the signal timing of the display with the graphic card. If the image appears to be unstable or isflickering,usethisfunctiontocorrectit.

ClockAdjust to achieve an optimal image when there is verticalflickering.

H. Position Adjust the horizontal position of the image using the left and right arrows. The range of movement will depend on the image source.

V. PositionAdjust the vertical position of the image using the left arrow to bring the image up and the right arrow to bring the image down. The range of movement will depend on the image source.

Digital ZoomUse the left arrow to zoom out and the right arrow to zoom in.

V. KeystoneUse the left and right arrows to adjust vertical image distortion. Use this option if the image appears like a trapezoid instead of rectangular.

Ceiling MountFront – The image will project straight on the screenFront ceiling – Default selection. When selected the image will turn upside down.Rear – The image will reverseRearceiling–Imagewillreverseandflipupsidedown

8

Settings

LanguageSwitchtheOSDtoadifferentlanguage:

• Press the right arrow to enter the submenu• Use the up and down arrows to select the

language• Presstherightarrowtofinalizetheselection

Menu LocationChoose the menu location on the display screen.

VGA Out(Standby)Choose On to enable VGA Out connection.

LAN (Standby)Choose On to enable LAN connection. Choose Off to disable LAN connection.

VGA 2 (Function)Input – Choose Input to allow the VGA port to work as a VGA input function.

Output – Choose Output to enable the VGA Out function once the projector is powered on.

Test PatternDisplay a test pattern.

ResetReturn all parameters on all submenus in the OSD to the factory default settings.

9

Volume

VolumeControl the following:

• Speaker• Line out• Microphone• Mute• Volume• Microphone Volume

10

Options

LogoSet the desired start-up screen. Any changes that aremadetothissettingwilltakeeffectthenexttime the projector is powered on.

• Default – The default start-up screen• User – Use a stored picture from the Logo

Capture function

Logo Capture Click on the arrow to take a screenshot of the image currently displayed on the screen. The OSD menu will not appear in the screenshot and the image can now be used as the projector start-up screen.

Auto Source• On – The projector will search for other

signals if the current input signal is lost• Off–Theprojectorwillonlysearchcurrent

input connection

InputClick on the arrow to enable or disable input sources. The projector will not search for inputs that are not selected.

Auto Power Off (Min)Set the countdown timer interval. The countdown timer will start once the projector stops receiving signals.Whenthecountdownisfinished,theprojectorwillautomaticallypoweroff.

SSI Settings SSI Hours Used (Normal) – Displays the number of hours the projector has been run in normal modeSSI Hours Used (ECO) – Displays the number of hours the projector has been run in ECO modeSSI Power Mode – Choose between normal and ECO mode. ECO mode will dim the projector lamp to lower power consumption and extend the lamp life.

High AltitudeOn – The built-in fans run at high speed. Select this option when using the projector at altitudes above 2,500ft.(762m)orhigher.Off–Thebuilt-infansautomaticallyrunatavariablespeed according to the internal temperature

Filters Reminder (Hour)Filters Remind (Hour) – Set when you would like to beremindedtochangethefilterCleaning up Reminder – Select Yes to reset reminder afterreplacingorcleaningthefilter

InformationDisplay the projector information. View the modelname, SNID, source, resolution, software version and aspect ratio on the screen.

11

Interactive

The Interactive function is available when displaying a graphic source from HDMI/VGA input. Other sources are not supported.

Interactive Settings• Choose On to enable the interactive function• Choose Off to disable the interactive function

Network

Status – Display the network connection statusDHCP –ConfiguretheDHCPsettings.Choose

On to let the projector obtain an IP address automatically from your network. Choose Off to assign IP, subnet mask, gateway and DNS configurationmanually.

IP Address – Display an IP addressSubnet Mask – Display the subnet mask number

Gateway – Display the default gateway of the network connected to the projector

DNS – Display the DNS numberMAC Address – Display the MAC addressGroup Name – Display the group nameProjector Name – Display the projector nameLocation – Display the projector locationContact – Display the contact information

12

Touch module on-screen display menuConfiguration

Interactive ModeFinger/Stylus –enablesfull-fingertouchandactivates pen capabilities

Active pen – enables active pen only. This is necessary when using the pen interactively with the mobile cart.

Touch Area SettingAuto – automatically sets the area for interactivity throughasequenceofflashingdots

Manual – manual control over each corner location (P1-P4) of the interactive area using a screen capture of the projected image. Used when tighter control over the interactive area is required.

CalibrationAuto – automatically sets the calibration through asequenceofflashingdots

Manual – nine-point manual calibration. Used mainly when higher touch accuracy is required.

Touch SensitivitySlider control – used when touch behavior is intermittent, inaccurate or unresponsive

• Minimum 0 – least sensitive• Maximum 10 – most sensitive

For bright rooms with lots of sunlight, adjust the slider lower so that it is less sensitive to unintended infared light. For dim rooms or poor touch behavior, adjust the slider higher.

MatchingAutomatically set when the Number of Displays configurationissettoDual.Noinputisrequired.

Note: When using auto alignment or auto calibration, do not obstruct the projector. Stand back at least 3’ (1 m) during the pattern sequence.

Light rooms Dark rooms

1 70 62 83 94 105

13

Settings

Installation GuideStep-by-step instructions to install and align the touch module. To be used during the initial setup only.

Troubleshooting ViewerProvides a real-time infared camera view of the interactive area. Used to show areas of touch feedback within the set area for interactivity.

Restore Default SettingRestores the touch module to factory settings

Language SettingProvides language support for 17 languages

Number of DisplaysAutomatically detects the number of displays based on the installation setup

• Single – 1 projector: 1 PC• Dual – 2projectors:1PC

14

Information

AboutDisplays the touch driver information and camera firmwareversion.

HelpProvides the link to the Nureva customer support portal and a direct email link to Nureva support support@nureva.com.

15

Multimedia

Projectmediafiles(photos,videos,music,documents)storedonthefollowingdevices:• Wireless dongle –Wirelesslyaccessthemediafilesstoredonyourmobilephone,tablet,PC,notebook

or desktop• USB flashdrive –Directlyaccessthemediafilesstoredinthedevice

How to access multimedia mode:

1.  PlugawirelessdongleorUSBflashdriveintotheUSBconnectoratthebackoftheprojector2.  Press the input button on the remote control or on the control panel to turn on the projector. When

the input menu appears, press the arrow keys to select the Multimedia, and then the Enter key to confirm.

Supported file formatsPhoto – BMP, JPG, JPEG, PNGMusic – MP3, WMAVideo – AVI, MOV, MP4, RM, RMVB, DAT, MPG, ISO, TS, MKV, VOB AND WMVDocument – Word®, Excel®, PPT®, PDF

Mobile display

1.  On the multimedia menu, select Mobile/Tablet

2.  On your mobile device or tablet PC, download the EZ-view application from the App Store (iOS) or the Play Store (Android™)

3.  Enable your mobile device or tablet PC’s Wi-Fi function, and search the AP name listed in the Wi-Fi network list.

4.  Enter the password when prompted

5.  Launch the EZ-view application and enter the PCTOOL password

6.  Waituntiltheconnectionisestablished.NowthemediafilesonyourmobiledeviceortabletPCcanbeaccessed using the projector.

16

Laptop display

1.  On multimedia menu, select Laptop2.  Enable your laptop or notebook Wi-Fi function, and search the AP name listed in the Wi-Fi network list3.  Enter the password when prompted4.  Open your web browser and enter the IP address5.  Select Wi-Fi on the left side of the screen and install the application required by the operating system6.  Launch the EZview application and enter the control code shown on the bottom right side of the screen7.  Waituntiltheconnectionisestablished.Themediafilesonyourlaptopornotebookcannowbeaccessed

using the projector.

Desktop display

1.  On the multimedia menu, select Desktop

2.  Open your web browser and enter the IP address

3.  Then select Wi-Fi on the left side of the screen and install the application required by your operating system

4.  Launch EZview application and enter the control code shown on the bottom right side of the screen

5.  Waituntiltheconnectionisestablished.Themediafilesonyourdesktopcannowbeaccessedusingtheprojector.

17

USB storage display

1.  On the multimedia menu, select USB Disk

2.  UsethearrowkeystoselectthefilecategoryandpressEnter

3.  UsethearrowkeystoselectthefiletovieworplayandpressEnter toconfirm

Configuring multimedia display settings

1.  On the multimedia menu, select Settings

2.  Use the arrow keys to choose the desired menu option and press Enter to access the submenu for your selection

Menu options:System–ViewthefirmwareversionandupdatefirmwareVideo – Change the display ratio and set the repeat modePhoto – Change the display ratio, slideshow pattern and slideshow durationMusic – Set the repeat modeWi-Fi–ConfiguretheWi-Ficonnection

3.  Use the arrow keys to select or adjust the setting, and press Enter toconfirm

18

RS232commands

RS232 port setting

RS232 signals connection

Items Method

Communication method Asynchronus communication

Bits per seconds 19,200

Data bits 8 bits

Parity None

Stop bits 1

Flow control None

CD

RXD

TXD

DTR

SG

DSR

RTS

CTS

RING

CD

TXD

RXD

DTR

SG

DSR

RTS

CTS

RING

1

2

3

4

5

6

7

8

9

1

2

3

4

5

6

7

8

9

⃝

⃝

⃝

⃝

⃝

⃝

⃝

⃝

⃝

⃝

⃝

⃝

⃝

⃝

⃝

⃝

⃝

⃝

19

Commands set list

Command Command description

ASCII code(space before “n”) Projector return N value

IR/Keypad Power #0100 n 0:Off1 : On

IR/Keypad INput source #0105 n

1 : VGA 12:VGA23 : HDMI 14:HDMI25 : Video6 : Multimedia

IR/Keypad Video source resync #0106 n

Screen Projection orientation #0123n

1 : Front2:Rear3 : Front ceiling4 : Rear ceiling

Setting Language #0130 n

1 : English2:German3 : Swedish4 : French5 : Arabic6 : Dutch7 : Norwegian8 : Danish9:SimplifiedChinese10 : Polish11 : Korean12:Russian13 : Spanish14 : Traditional Chinese15 : Italian16 : Portuguese17 : Turkish18 : Japanese

Volume Mute #0140 n 0:Off1 : On

Volume Volume #0141 n 0~30Options Autopoweroff(min) #0150 n Step = 5

Screen Aspect ratio read #01120n Okn n:1/2/3/4=Auto/4:3/16:9/16:10(ultrawide)

Options Input source (curr.src) #01160 n Okn n:0/1/2/3/4/5/6=None/VGA1/VGA2/HDMI1/HDMI2/Video/Multimedia

Options Software version #01161 n Okddd ddd : FW version

Options Information #01162n Okabbbbccdddeea: Power status / b: D LD Hour / c: Input source / d: Firmware version / e: Color mode

Options Serial number #01163 n Okaaaaaaaaaaaaaaaaa Options Power state #01164 n Okn n: 0/1 = Standby / Power on

Control command syntax[Header][MsgID][Command][Space][Value]Note:Thereisa<CR>afterallASCIIcommands,0x0Dis<CR>inASCIIcode

Controlcommandexample:Poweron#00001(ASCIIcode)233030302030D(Hexcode)

Projector returnPass:PFail:F

UART connection settingsBaudrate:19200Databits:8Parity:NoneStopbits:1

20

Crestron Crestron Main Page

Item Value/Range Default Remark Power Button Defined by Crestron Volume- Button Defined by Crestron Volume+ Button Defined by Crestron Mute Button Defined by Crestron VGA-1 Button Defined by Crestron VGA-2 Button Defined by Crestron Composite Button Defined by Crestron Multimedia Button Defined by Crestron HDMI-1 Button Defined by Crestron HDMI-2 Button Defined by Crestron Enter Button Defined by Crestron Menu Button Defined by Crestron Up, Down,Left,Right Button Defined by Crestron Freeze Button Defined by Crestron Contrast Gauge Defined by Crestron Brightness Gauge Defined by Crestron Color Gauge Defined by Crestron Sharpness Gauge Defined by Crestron

Main page

Settings

• Power• Volume –• Volume +• Mute• VGA–1• VGA–2

• Composite• Multimedia• HDMI–1• HDMI–2• Enter• Menu

• Up, Down, Left, Right• Freeze• Contrast• Brightness• Color• Sharpness

Crestron RoomView™ is a program that monitors each projector, including the projector’s online status, system power, network setting and hardware faults, plus any custom attributes defined by the administrator.

For more information on Crestron, including purchasing or downloading RoomView, go to

http://www.crestron.com or www.crestron.com/getroomview.

Note: RoomView’sfunctionissetaccordingtotheproducts’modelsandspecifications.

Crestron® room control

21

Crestron Tool Page

Item Value/Range Default Remark IP Address Customer supplied IP ID Customer supplied Port Customer supplied Group Name Customer supplied Location Customer supplied Projector Name Customer supplied DHCP Customer supplied IP Address Customer supplied Subnet Mask Customer supplied Default Gateway Customer supplied DNS Server Customer supplied User Password Customer supplied Admin Password Customer supplied

Tool page

Settings

• IP Address• IP ID• Port• Group Name• Location

• Projector Name• DHCP• IP Address• Subnet Mask• Default Gateway

• DNS Server• User Password• Admin PasswordCrestron Information Page

Item Value/Range Default Remark Group Name Customer supplied Location Customer supplied Firmware Version Customer supplied Mac Address Customer supplied Resolution Customer supplied Lamp Hours Customer supplied Projector Name Customer supplied Power Status Customer supplied Source Customer supplied Image Customer supplied Projection Customer supplied Lamp Mode Customer supplied Error Status Customer supplied

Information page

Settings

• Group Name• Location• Firmware Version• Mac Address• Resolution

• SSI Hours• Projector Name• Power Status• Source• Image

• Projection• Error Status

22

Web browser projector control

Projector information

Web Page Control GUI Projector Information

Item Value/Range Default Remark Model Name NA Customer supplied Group Name NA Customer supplied Projector Name NA Customer supplied Location NA Customer supplied Contact NA Customer supplied Status NA Customer supplied Lamp Hours NA Projector Display Hours NA Projector Firmware Version NA Projector MPU Version NA Projector Network Version NA Projector Input NA Projector Resolution NA Projector Projector ID NA Customer supplied Failure Log NA Projector Serial Number NA Projector Administrator Password NA Customer supplied IP Address NA Projector Mac Address NA Projector Language NA English

Enable web browser control on the projectorManage your projector settings over a web graphic user interface (GUI) using the steps in this section.

1.  On the Network settings page in the projector’s OSD, turn on DHCP

2.  Open your browser and type in the IP address assigned to the projector as shown in the Network Settings in the OSD

23

LAN setting

Wi-Fi

LAN Setting

Item Value/Range Default Remark DHCP On/Off Off IP Address TDB with connection 10.0.21.200 Subnetmask TDB with connection 255.255.0.0 Gateway TDB with connection 10.0.0.254 DNS TDB with connection 0.0.0.0 Group Name TDB with connection GROUP Projector Name TDB with connection PROJECTOR Location TDB with connection LOCATION Contact TDB with connection NA

Wi-Fi

Item Value/Range Default Remark App Download Link Windows/MacOS/iOS/Andriod For Multi Media Only

Setting DefaultDHCP OffIP Address 10.0.21.200Subnet Mask 255.255.0.0Gateway 10.0.0.254DNS 0.0.0.0Group name GROUPProjector name PROJECTORLocation LOCATIONContact N/A

Setting Value/Range

App download link Windows™/MacOS/iOS/Android (for multimedia only)

24

Projector status and controlProjector Status and Control

Projector Status and Control

Setting Value/range DefaultProjector Status On/Off/Powering/Cooling OffInput HDMI1/HDMI2/VGA1/VGA2/Composite/

MultimediaLogo Default/User DefaultCeiling Mount Front/Front ceiling/Rear/Rear ceiling Front ceilingHigh Altitude On/Off OffAuto Source On/Off OnLASER Power Mode Normal/ECO NormalAutoPowerOff(min) 0~120(step:5) 20Color Mode PC/Bright/Movie/Game/User PCAspect Ratio Auto/4:3/16:9/16:10/Ultrawide AutoVideo Mute On/Off OffBrightness 0~100 50Contrast 0~100 50Clock Depend on sourcePhase Depend on sourceSaturation 0~100 50Hue 0~100 50Sharpness 0~31 16Gamma 0~3H-Position Depend on sourceV-Position Depend on sourceKeystone -40~40 0Zoom 0~10 0Volume 0~30 15Microphone Volume 0~30 15

25

Email alertE-mail Setting

Item Value/Range Default Remark E-mail Alert Enable/Disable Disable TO User input Null CC User input Null From User input Null Subject User input Null Out going SMPT Server User input Null User Name User input Null Alert Condition Checked item Empty

Setting DefaultE-mail alert DisabledTOCCFromSubjectOutgoing SMPT serverUsernameAlert Condition Empty

Password settingPassword Setting

Item Value/Range Default Remark Password Enable/Disable Disable New Password User input Null Confirm Password User input Null

Setting DefaultPassword Enable/DisableNew PasswordConfirmPassword

26

Video compatibility modes

VGA analog

a. PC signalModes Resolution V. Frequency (Hz) H. Frequency [Hz]

VGA

640 x 480 60 31.5640 x 480 67 35.0640 x 480 72 37.9640 x 480 75 37.5640 x 480 85 43.3

IBM 720x400 70 31.5

SVGA

800 x 600 56 35.1800 x 600 60 37.9800 x 600 72 48.1800 x 600 75 46.9800 x 600 85 53.7

Apple®, MAC II 832x624 75 49.1

XGA

1024x768 60 48.41024x768 70 56.51024x768 75 60.01024x768 85 68.71024x768 120 99.0

Apple, MAC II 1152x870 75 68.7

SXGA1280x1024 60 64.01280x1024 72 77.01280x1024 75 80.0

QuadVGA1280x960 60 60.01280x960 75 75.2

SXGA + 1400 x 1050 60 65.3UXGA 1600x1200 60 75.0

27

VGA analog continued

b. Extended wide timingModes Resolution V. Frequency (Hz) H. Frequency [Hz]

WXGA

1280x720 60 44.81280x800 60 49.61366 x 768 60 47.71440 x 900 60 59.9

WSXGA X + 1680 x 1050 60 65.3c. Component signal

Modes Resolution V. Frequency (Hz) H. Frequency [Hz]

480i 720x480(1440 x 480) 59.94(29.97) 15.7

576i 720x567(1440 x 576) 50(25) 15.6

480p 720x480 59.94 31.5576p 720x576 50 31.3

720p1280x720 60 45.01280x720 50 37.5

1080i1920x1080 30 (30) 33.81920x1080 50(25) 28.1

1080p1920x1080 2398/24 27.01920x1080 60 67.51920x1080 50 56.3

28

HDMI digital

a. PC signalModes Resolution V. Frequency (Hz) H. Frequency [Hz]

VGA

640 x 480 60 31.5640 x 480 67 35.0640 x 480 72 37.9640 x 480 75 37.5640 x 480 85 43.3

IBM 720x400 70 31.5

SVGA

800 x 600 56 35.1800 x 600 60 37.9800 x 600 72 48.1800 x 600 75 46.9800 x 600 85 53.7

Apple, MAC II 832x624 75 49.1

XGA

1024x768 60 48.41024x768 70 56.51024x768 75 60.01024x768 85 68.71024x768 120 99.0

Apple, MAC II 1152x870 75 68.7

SXGA1280x1024 60 64.01280x1024 72 77.01280x1024 75 80.0

Quad VGA1280x960 60 60.01280x960 75 75.2

SXGA + 1400 x 1050 60 65.3UXGA 1600x1200 60 75.0

29

HDMI digital continued

b. Extended wide trimmingModes Resolution V. Frequency (Hz) H. Frequency [Hz]

WXGA

1280x720 60 44.81280x800 60 49.61366 x 768 60 47.71440 x 900 60 59.9

WSXGA + 1680 x 1050 60 65.3

c. Video signalModes Resolution V. Frequency (Hz) H. Frequency [Hz]

480p 640 x 480 59.94/60 31.5

480i 720x480(1440 x 480) 59.94(29.97) 15.7

576i 720x576(1440 x 576) 50(25) 15.6

480p 720x480 59.94 31.5576p 720x576 50 31.3

720p1280x720 60 45.01280x720 50 37.5

1080i1920x1080 60 (30) 33.81920x1080 50(25) 28.1

1080p1920x1080 23.98/24 27.01920x1080 60 67.51920x1080 50 56.3

d. HDMI 1.4a mandatory 3D timing - video signalModes Resolution V. Frequency (Hz) H. Frequency [Hz]

Frame packing

720p 50 31.5720p 59.94/60 15.7

1080p 23.98/24 15.6

Side-by-side(half)

1080i 50 31.51080i 59.94/60 31.3

Top and bottom

720p 50 45.0720p 59.94/60 37.5

1080p 23.98/24 33.8

30

InstallingandcleaningthedustfilterWerecommendcleaningthefilterannually.Ifyouareoperatingtheprojectorinadustyenvironment,werecommendcleaningthefiltersemi-annuallyorafter1,000hours.Newfilterscanbeorderedviaorders@nureva.com using the service part number SRV-FILTER.

Beforeyoubegin,turntheprojectoroffandunplugthepowercord.

1.  Pullthedustfiltercontaineroutfromtheprojector

2.  Carefullyremovethedustfilterfromthedustfiltercontainer

3.  Eithercleanthefilterorreplaceitwithanewfilter

4.  Putthedustfiltercontainerbackinsidetheprojectorandpressthepowerbuttontoturntheprojector on

5.  Press the menu button to enter the OSD, select the options menu and use the Filters Remind option to reset the counter

31

Regulation and safety notices

This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turningthedeviceoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowing measures:

• Reorient or relocate the receiving antenna• Increase the separation between the device and receiver• Connectthedeviceintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected• Consult the dealer or an experienced radio/television technician for help

Notice: Shielded cablesAll connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

CautionChangesormodificationsnotexpresslyapprovedbythemanufacturercouldvoidtheuser’sauthority,whichis granted by the Federal Communications Commission, to operate this projector.

Operation conditionsThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  This device may not cause harmful interference and

2.  This device must accept any interference received, including interference that may cause undesired operation

FCC Notice

This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.

Notice: Canadian users/Remarque à l’intention des utilisateurs Canadiens

32

Regulation and safety noticesDeclaration of Conformity for EU countries

• EMCDirective2004/108/EC(includingamendments)

• LowVoltageDirective2006/95/EC

• R & TTE Directive 1999/5/EC (if product has RF function

SAFETY WARNINGS AND IMPORTANT INFORMATION

WEEE StatementTo return any product for proper treatment and recycling, contact your local authority or your local reseller.

33

PRÉCAUTIONS DE SÉCURITÉ INFORMATION IMPORTANT