Upload
nu-horizons
View
332
Download
9
Embed Size (px)
DESCRIPTION
Your gateway to today's leading technology products.
Citation preview
March 2009
In This Issue: Bus Interface
5V RS-485/RS-422 Half-Duplex Transceiver
High-Performance Low Voltage UARTs with 16/32/64-Byte FIFOs
DataCom
Single-port 10/100/1000Base-T Gigabit Transceiver
Development ToolsNu HorizonsInreviumXilinx
Logic
Spartan-6 FPGA Families
Virtex-6 FPGA Families
Power & Battery Management
125Msps ADC at 125mW
1A Micropower Step-Down Switching Regulator
5V RS-485/RS-422 Half-DuplexTransceiverIdeal for Industrial and Remote Data Collection Applications The SP4082E is designed for reliable, bidirectional communication on multipoint bus transmission lines. The device contains one differential driver and one differential receiver. It is a half-duplex device and complies with TIA/EIA-485 and TIA/EIA-422 standards. This device is ruggedized for use in harsh operating conditions over the entire common-mode voltage range from -7V to +12V. Receivers are specially designed to fail-safe to a logic high output state if the inputs are open or shorted. All RS-485 bus-pins are protected against severe ESD events up to ±15kV (Human Body Model). Drivers are protected from excess current flow caused by bus contention or output short-circuits by both an internal current limit and a thermal-overload shutdown. Up to 256 transceivers may coexist while preserving full signal margin.
The device operates from a single 5.0V power supply and draws negligible quiescent power. The device has an independent enable and disable for the driver and receiver and will enter a low power shutdown mode if both driver and receiver are disabled. All outputs maintain high impedance during shutdown or when powered-off.
Bus
Inte
rfac
e
Features Benefits
5.0V single supply operation
Controlled driver slew rates 115kbps
Receiver failsafe on open or shorted lines
1/8th Unit Load
Robust ESD protection for RS-485 pins ±15kV
Human Body Model
Driver short circuit current limit and thermal shutdown
for overload protection
Industry standard package footprint
Low EMI
Higher Density Network
Vigorous ESD protection
Applications
Motor Control
Building Automation
Security Systems
Remote Meter Reading
8 PIN NSOICSP4082E
Half Duplex
1
2
3
4 5
6
7
8
GND
A
B
VccRO
RE
DE
DI
Pin Number Pin Name Pin Function
1 RO Receiver Output. When RE is low and if (A – B) ≥ -40mV, RO is high. If (A – B) ≤ - 200mV, RO is low.
2 REReceiver Output Enable. When RE is low, RO is enabled. When RE is high, RO is high impedance. Drive RE high and DE low to enter shutdown mode.
3 DEDriver Output Enable. When DE is high, outputs are enabled. When DE is low, outputs are high impedance. Drive DE low and RE high to enter shutdown mode.
4 DIDriver Input. With DE high, a low level on DI forces non-inverting output low and inverting output high. A high level on DI forces non-inverting output high and inverting output low.
5 GND Ground
6 A Non-inverting Receiver Input and Non-inverting Driver Output
7 B Inverting Receiver Input and Inverting Driver Output
8 Vcc Positive Supply VCC. Bypass to GND with a 0.1uF capacitor
For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts
Features Benefits
Intel, Motorola or VLIO Bus Interface
20Mbps Maximum Data Rate
Selectable or Programmable TX/RX trigger levels
TX/RX FIFO Level Counters
Independent TX/RX Baud Rate Generator
Fractional Baud Rate Generator
Auto RS-485 Half-Duplex Direction Control
Multidrop Mode w/ Auto Address Detect
PowerSave Mode
1.62V-3.63V Supply Voltage
Automatic Hardware/Software Flow Control
Highest Performance at Lower Supply Voltages
Overall System Cost Reduction
Shorter Time-to-Market
Applications
Smart Phones Personal Digital Assistants (PDAs) Battery-Operated Devices Global Positioning System (GPS) Bluetooth Point-of-Sales (POS) Systems Gaming Systems Industrial Controls
High-Performance Low Voltage UARTs with 16/32/64-Byte FIFOs Smallest and Fastest Single-Channel Universal Asynchronous Receiver Transmitter (UART) SeriesThe XR16M58x/68x/78x series are part of the enhanced Universal
Asynchronous Receiver and Transmitter (UART) family with 16, 32
and 64 bytes of transmit and receive FIFOs. These devices have
selectable or programmable transmit and receive FIFO trigger levels,
automatic hardware and software flow control, and compatible with
the Intel, Motorola, or VLIO bus interface.
Bus Interface
VCC
XTAL1XTAL2Crystal Osc / Buffer
TX , RX,RTS #, CTS#,DTR #, DSR#,
Intel or Motorola
Bus Interface
64 Byte RX FIFORX BRG
IRENDEC
TX & RX
UART
Regs
A2:A0
PwrSave
64 Byte TX FIFO
RI #, CD#
RESET(RESET#)
IOW# (R/W#)
CS#
INT/IRQ#
IOR#
GND
(1. 62 to 3. 63 V)
TX BRG
D7:D0
16/68#
VCC
XTAL1XTAL2Crystal Osc/Buffer
TX, RX,RTS#, CTS#,DTR#, DSR#,
VLIO BusInterface 64 Byte RX FIFORX
BRG
IRENDEC
TX &RX
UART
Regs
LLA#
PwrSave
64 Byte TX FIFO
RI#, CD#
RESET#
AD7:AD0
IOW#
CS#
INT
IOR#
GND
(1.62 to 3.63 V)
TX BRG
XR16M781 Block DiagramXR16M780 Block Diagram
For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts
M E D IAIN TE R FA C E
PM ATX 10/100 /1000
PM AR X1000
PM AR X100
PM AR X10
C lockR eset
P C S10
A U TON EG O TIA TIO N
P C S100
PC S 1000
G M II/R G M II/M IIInterface
LE DD R IVE R S
C onfigurations
Features Benefits
10/100/1000Base-T IEEE 802.3 complianceStandard compliance ensures to work with other standardcompliant, already deployed devices.
GMII, RGMII, and MII MAC interfacesFlexible MAC interfaces (GMII/MII for KSZ9021GQ and RGMIIfor KSZ9021RL) support direct connection to MACs in Ethernetprocessors and switches at various data rates.
Integration of termination resistors on the chipOn-chip termination (eliminating 8 external resistors) not onlysimplifies PCB design and reduces system BOM, but alsoimproves overall signal integrity and EMI emission.
Integration of a LDO controller on the chipIntegration of a LDO controller permits a low cost MOSFET tosupply the 1.2V core, which reduces board cost and simplifiesboard layout.
LinkMD® TDR-based cable diagnosticsBuilt-in LinkMD® diagnostics helps identification of commoncabling problems, including those not addressed by IEEE. Itsimplifies network deployment and reduces network downtime.
Automatic MDI/MDIX crossover for IEEE 802.3 and EIA/TIA 568 standards at all speeds of operation
Auto-MDI/MDIX eliminates the need for cross-over cable,thus reduces installation costs. Easy to use.
Single-port 10/100/1000Base-T Gigabit Transceiver KSZ9021GQKSZ9021RL
The KSZ9021GQ and KSZ9021RL are single-port 10/100/1000Base-T Gigabit transceivers,
supporting data transfer over standard CAT-5 unshielded twisted pair cable. This device offers
robust performance and low power consumption. On-chip integration of termination resistors
and LDO controller, along with built-in diagnostic features, significantly reduces the cost and
the complexity of Gigabit Ethernet applications. This device is ideal for enabling Gigabit Ethernet performance in SOHO and SMB
networking applications, such as media converter, GEPON ONU router, wired/wireless Gigabit SOHO/SMB router, and VoIP gateway.
The device is available in two RoHS-compliant package options - 128-pin QFP (KSZ9021GQ, supporting GMII/MII) and 64-pin E-LQFP
(KSZ9021RL, supporting RGMI). Industrial grade is also available.
Da
tac
om
Block Diagram
Applications
Wired/wireless Gigabit SOHO/SMB Router SOHO Media Center Voice-over-Internet Protocol (VoIP) Gateway Network Attached Storage Laser Printers and Projectors GEPON ONU Router Media Converter VPN/Firewall based SMB/SME Router Gigabit Ethernet LAN on Motherboard Integrated Broadband CPE (ADSL/VDSL/FTTH) Router
LinkMD is a registered trademark of Micrel, Inc.
For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts
Spartan-6 FPGA Families The Programmable Foundation for Targeted Design Platforms
The Spartan®-6 family provides leading system integration
capabilities with the lowest total cost for high-volume
applications. The eleven member family delivers expanded
densities ranging from 3,400 to 148,000 logic cells, with half
the power consumption of previous Spartan families and faster,
more comprehensive connectivity. Built on a mature 45 nm
low-power copper process technology that delivers the optimal
balance of cost, power, and performance, the Spartan-6 family
offers a new, more efficient, dual-register 6-input look-up table
(LUT) logic and a rich selection of built-in system-level blocks.
Log
ic
Features
Two Base Platforms
Designed for low cost
Low static and dynamic power
Multi-voltage, multi-standard SelectIO banks
High-speed GTP serial transceivers in the LXT FPGAs
Integrated Endpoint block for PCI Express designs (LXT)
Efficient DSP48A1 slices
Integrated Memory Controller blocks
Abundant logic resources with increased logic capacity
Block RAM with a wide range of granularity
Clock Management Tile (CMT) for enhanced performance
Simplified configuration, supports low-cost standards
Enhanced security for design protection
Faster embedded processing with enhanced, low cost,
MicroBlaze™ soft processor
Low cost, integrated PCI® technology support compatible
across 32 bit and 64 bit, 33 MHz and 66 MHz specifications
Industry-leading IP and reference designs
Learn more about View the webcast at http://www.xilinx.com/events/webcasts.htm.
For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts
The Virtex®-6 family provides the newest, most advanced
features in the FPGA market. Using the third generation
ASMBL™ (Advanced Silicon Modular Block) column-based
architecture, the Virtex-6 family contains multiple distinct
platforms (sub-families). Each platform contains a different ratio
of features to address the needs of a wide variety
of advanced logic designs.
Features
Two Base Platforms
Cross-platform compatibility
Advanced, high-performance, FPGA Logic
Powerful mixed-mode clock managers (MMCM) clocking
36-Kb block RAM/FIFOs
High-performance parallel SelectIO technology
Advanced DSP48E1 slices
Flexible configuration options
System Monitor capability on all devices
Integrated interface blocks for PCI Express designs
RocketIO™ GTX transceivers 150 Mb/s to 6.5 Gb/s
Integrated 10/100/1000 Mb/s Ethernet MAC block
40 nm copper CMOS process technology
1.0V core voltage (-1, -2, -3 speed grades only)
Lower-power 0.9V core voltage (-1L speed grade only)
High signal-integrity flip-chip packaging available in standard or Pb-free package options
Virtex-6 FPGA Families The Programmable Foundation for Targeted
Design Platforms
Log
ic
Learn more about View the webcast at http://www.xilinx.com/events/webcasts.htm.
For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts
Features Applications
Full rate CMOS using 14 data lines
Double data rate (DDR) CMOS, 7 data lines
DDR LVDS, 14 data lines, for reduced digital noise
Straight binary or twos complement data coding
Selectable LVDS output current (1.75 to 4.5 mA), to match output current to the load, while minimizing power dissipation
Internal 100-ohm resistors which you can switch in, to absorb reflections due to impedance mismatch at the receiver
A data randomizer which scrambles the output bits via an exclusive-OR circuit, to reduce noise coupling from major signal transitions and improve SFDR (the data receiver, of course, must do a reverse XOR to unscramble them); LTC claims this can reduce residual tones caused by digital feedback by 10-15 dB
Cellular Base Stations
Communications
Instrumentation
Multi-Channel Data Acquisition
Non-Destructive Testing (NDT)
Portable Medical Imaging
Software Defined Radio (SDR)
LTC®2261 — 125Msps ADC at 125mWOne-Third the Power of Comparable High-Speed ADCs
The LTC2261-14/LTC2260-14/LTC2259-14 are sampling 14-bit A/D converters designed for digitizing high frequency, wide dynamic range signals. They are perfect for demanding communications applications with AC performance that includes 73.4dB SNR and 85dB spurious free dynamic range (SFDR). Ultralow jitter of 0.17psRMS allows undersampling of IF frequencies with excellent noise performance.
DC specs include ±1LSB INL (typical), ±0.3LSB DNL (typical) and no missing codes over temperature. The transition noise is a low 1.2LSBRMS. The digital outputs can be either full rate CMOS, double data rate CMOS, or double data rate LVDS. A separate output power supply allows the CMOS output swing to range from 1.2V to 1.8V. The ENC+ and ENC– inputs may be driven differentially or single-ended with a sine wave, PECL, LVDS, TTL or CMOS inputs. An optional clock duty cycle stabilizer allows high performance at full speed for a wide range of clock duty cycles
Power & B
attery Managem
ent
Linear’s newest high-speed ADC family achieves 1/3rd the power consumption of existing solutions without compromising AC performance. Whether operating at full speed or in sleep mode, the LTC2261 significantly lowers the power budget for high-speed data acquisition, making it possible to “cut the cord” and migrate products into the portable world.
–
+INPUT
S/HCORRECTION
LOGICOUTPUTDRIVERS
14-BITPIPELINEDADC CORE
CLOCK/DUTYCYCLE
CONTROL
D13•••
D0
125MHz
CLOCK
ANALOGINPUT
CMOSORLVDS
1.2VTO 1.8V
1.8V
VDD
OVDD
OGND
GND
2-Tone FFT, fIN = 70MHz and 75MHz
FREQUENCY (MHz)0
–100–110–120
–70
–60
–80–90
AMPL
ITUD
E (d
BFS)
–50
–30
–40
–20
–10
0
10 20 30 40 50 60
Typical Application
For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts
Features Applications
Wide input voltage range of 3.6V to 36V, with transient protection to 60V
Up to 1A of continuous output current
Up to 90% efficiency
Only 75μA of quiescent current
Adjustable, Synchronizable switching frequency: 250kHz to 2.2MHz
DA pin to permit the OVLO at any operating frequency
Output is adjustable down to 0.8V
Soft-start capability
Power Good Flag
Tiny 3mm x 3mm DFN-12
Automotive Battery Regulation
Automotive Entertainment Systems
Industrial Supplies
Power for Portable Products
Distributed Supply Regulation
LT3682 - 1A Micropower Step-Down Switching Regulator 36V
IN (60V Transient Protection) 1A,
Micropower Step Down ConverterModern automobile, industrial and telecomm environments continue to include increasingly complex electronic systems. Additionally,
these electrical and physical environments continue to be very harsh for any type of electronics. Wide operating voltage requirements
coupled with large transient voltages and wide temperature variations combine to make life difficult on electronic systems. High efficiency
is of paramount importance as it minimizes thermal design considerations while also maximizing battery run time. Equally important is
very low quiescent current which minimizes the power drawn from a battery when the IC is in a standby mode. Many of these applications
operate from batteries, or utilize back-up batteries, in which a voltage rail must be maintained with no load current for an extended
period of time. Therefore, it is important to keep the quiescent current as low as possible. Common applications are automotive GPS,
security and environmental control systems as well as a myriad of industrial applications. Additionally, as manufacturers increase the
electronic content of their systems, the space
requirements continue to shrink demanding
smaller and more efficient power solutions.
The New Direction:
Linear Technology adds the LT3682 to its existing
family of high voltage Micropower monolithic
step-down converters to specifically address
these requirements. The LT3682 provides an
extremely compact 36VIN step-down solution
with transient protection to 60V. The device
provides improved performance in all key areas
including size, efficiency, ease of design, as well
as excellent thermal performance.
Power & B
attery Managem
ent
For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts For more information, including pricing, availability, datasheets and samples (if available), please visit http://uk.nuhorizons.com/FeaturedProducts
Nu Horizons Spartan™-3A Evaluation Kit
Inrevium VirtexTM-5 PCI Express Evaluation Board
Dev
elo
pm
ent
Too
ls
Nu Horizons offers a wide range of development/evaluation boards, tools and kts. For more information, please visit http://uk.nuhorizons.com/development
2x16Character Display
1 MB SRAM
SPIFlash
Pushbuttons8 LEDs
Headers
JTAG Header
XC3S200A FPGA
RS-232 50 MHz Crystal
USB
This low cost board features the new Spartan-3A Platform FPGA from Xilinx. The Spartan-3A Platform is perfect for applications where I/O count and capabilities matter more than logic density like bridging, differential signaling and memory interfacing applications, requiring wide or multiple interfaces and modest processing.
Key Features: Xilinx XC3S200A-4FTG25CES FPGA Linear Technology LTM4603 DC to DC power supply USB port 16x2 Tianma display 1 M ISSI SRAM LT1331 – Linear Technology 3V RS562 or 5V/3V RS232 transceiver LT1962 – Linear Technology 300mA, low noise, micropower LDO regulator LT3021 – Linear Technology 500mA, low voltage, very low dropout linear regulator LT4413 – Linear Technology Dual 2.6A, 2.5V to 5.5V fast ideal diodes LTM4603 – Linear Technology 6A DC/DC μModule with PLL, output tracking and margining
Ordering Info: NH-SPAR3A-EVL
Price: $125 (Use Promo Code 0309SP3A online for 20% off)
DC12V
Jumper
10pinPin Headers
XCF32PVO48
JTAG Port
DDR2 SDRAM(Chip)
DDR2 SO-DIMM
SMA x2
42pin I/O Expand x1
LX110T MGT Connector (4ch)
Camera_link
LX110T 42pin I/OExpand x2
SFP x2RS232C
MICTORConnector
Push SW (x4)
XilinxXC5VL50T/110T
-1FF1136
PCI-Express x8
LED (x8)
DIP SW (x8)
LXT110TPin Header
3.3V
2.5V
1.8V
1.2V
1.0V
0.9V Flash ROM
PHY
RJ45
TB-5V-LX-xxxT-PCIEXP is an ideal High-speed evaluation platform for 8-lane PCI-Express. In addition, it supports multiple High-speed serial transceiver interfaces with SFP and SMA connector ports. On-board Camera Link port is useful for a wide variety of video applications such as image processing. This Inrevium board product is produced by Tokyo Electron Device.
Ordering Info: TB-5V-LX50T-PCIEXP Price: $2,980 TB-5V-FX70T-PCIEXP Price: $4,980 TB-5V-FX70T-PCIEXP-512 Price: $5,060 TB-5V-LX330T-PCIE-EX Price: $14,980 TB-5V-SX240T-PCIE-EX Price: $19,800 TB-5V-FX200T-PCIE-EX Price: $11,980
by Tokyo Electron Device Ltd. Key Features:
FPGA: XC5VLXT 50/110 FF1136 PCI-Express V1.1 x8 DDR2 SDRAM chip: 512Mb x1 DDR2 SO-DIMM Slot x1 10/100/1000Mbps Ethernet MAC & PH CameraLink port x1 SMA connector x2 SFP x2
LTC1348 – Linear Technology 3.3V/5V low power RS232 3-driver/5-receiver transceiver LTC3413 – Linear Technology 3A, 2MHz monolithic synchronous regulator for DDR/QDR memory termination LTC3728 – Linear Technology Dual, 550kHz, 2-phase synchronous step- down switching regulator LTM4600 – Linear Technology 10A DC/DC μModule power supply
,
Nu Horizons Virtex™-5 LXT Evaluation Platform
Inrevium Virtex™-5 SXT High-Speed Computing Platform
De
velo
pm
en
t Too
ls
Nu Horizons offers a wide range of development/evaluation boards, tools and kts. For more information, please visit http://uk.nuhorizons.com/development
by Tokyo Electron Device Ltd.
Key Features: 10/100/1G Marvell Ethernet Phy LTC1326 – Linear Technology micropower precision triple supply monitor LTC3026 – Linear Technology 1.5A low input voltage VLDO linear regulator LTC3412 – Linear Technology 3A, 4MHz, monolithic synchronous step-down regulator LTC3418 – Linear Technology 8A, 4MHz, monolithic synchronous step-down regulator LTM4601 – Linear Technology 12A DC/DC μModule power supply 2x16 Tianma display ISSI DDR2 SDRAM 1 SFP connector 8 SMA connectors
Includes: Development board Power supply Reference design
Ordering Info: NH-5VLXT-EVL
Price: $799
MarvellEthernet Phy
RS-232 1 SFP8 SMAsCrystal
Platform Flash
JTAG Header
Headers
Linear TechAcquisition Header
16 MB Flash
64 MB DDR
Xilinx VirtexLXT50
Pushbuttons8 LEDs
Video DAC
2x16Character Display
The Virtex-5 LXT Platform FPGA is optimized for high-performance logic with low-power serial connectivity. This kit includes one of SPF and 8 SMA connectors for easy evaluation of MGT designs.
This new platform from the Tokyo Electron Device engi-neering team is designed specifically for computational intensive designs. Each 5VSX95T devices is connected to each of the other 3 devices by four dedicated GTP chan-nels for high speed communication between the devices.
Key Features: XC5VSX95T-1FF136 x4 DDR2 SDRAM x8 GTP x16 ch per FPGA X4 to each FPGA X4 SAMTEC connector Samtec High Speed Interface (120 pin) x1 per FPGA Optional Expansion capabilities x1 per FPGA
Includes: Evaluation Board Documentation Power Supply
Ordering Info: TB-5V-SX95T4-HSC
Price: Call Nu HorizonsDDR2
SDRAM
SX95T
DDR2 SDRAM
DDR2 SDRAM
SX95T
DDR2 SDRAM
DDR2 SDRAM
SX95T
DDR2 SDRAM
DDR2 SDRAM
SX95T
DDR2 SDRAM
This low cost evaluation kit from Nu Horizons is designed to help evaluate the new Spartan 3ADSP FPGAs from Xilinx. Peripherals include memory, analog circuitry, and a short range RF link.
Key Features: XC3SD1800A-4FGG646C Spartan-3A DSP FPGA 16 MB DDR2 SDRAM 16 MB SPI Flash 10/100 Ethernet PHY 14 bit Analog to Digital Converter Radio Transceiver Stereo DAC Video DAC 20x2 character LCD Display
Includes: Evaluation Board Documentation Power Supply
Ordering Info: NH-SPAR3ADSP-EVL
Price: $199.99
XC3SD1800ACS484
2x20 Display Pushbuttons
RS-232 Crystal
16 MB DDR2 SDRAM
10/100 Ethernet Phy
16 MB SPI Flash
Video DAC
Stereo DAC
LTC FastDAACConnector
RF Radio
8 LEDs
14 bit ADC
The Virtex-5 FXT Platform FPGA is optimized for high-performance logic with low-power serial connectivity. This kit includes one of SPF and 8 SMA connectors for easy evaluation of MGT designs.
Key Features: 5VFX30T FPGA 10/100/1G Marvell Ethernet Phy LTC1326 – Linear Tech micropower precision triple supply monitor LTC3026 – Linear Tech 1.5A low input voltage VLDO linear regulator LTC3412 – Linear Tech 3A, 4MHz, monolithic synchronous step- down regulator LTC3418 – Linear Tech 8A, 4MHz, monolithic synchronous step- down regulator LTM4601 – Linear Tech 12A DC/DC μModule power supply 2x16 Tianma display Micron DDR2 SDRAM 1 SFP connector 8 SMA connectors
Ordering Info: NH-5VFXT-EVL
Price: $849
Nu Horizons Spartan™-3A DSP Evaluation Kit
Nu Horizons Virtex™-5 FXT Evaluation Platform
Dev
elo
pm
ent
Too
ls
MarvellEthernet Phy
RS-232 1 SFP8 SMAsCrystal
Platform Flash
JTAG Header
Headers
Linear TechAcquisition Header
NAND Flash
64 MB DDR
Xilinx VirtexLXT50
Pushbuttons8 LEDs
Video DAC
2x16Character Display
Nu Horizons offers a wide range of development/evaluation boards, tools and kts. For more information, please visit http://uk.nuhorizons.com/development
Enhance Your Design...With Nu Horizons Education and Development Solutions
LabCam delivers online training opportunities in a way that recognizes the value of engineers’ time. As easily as You Tube® videos, engineers can quickly load and watch videos from industry leaders consisting of insights on products, evaluation kit overviews, end-user applications and more. Each tutorial is up to ten minutes in length and features technology experts, CEOs and/or peers introducing new solutions or explaining integral aspects of an important product, solution or application. This free value-added program is packaged for short, informative and high quality distance learning.
Nu Horizons is proud to present our education and training program, which offers engineers the opportunity to participate in technical seminars conducted by experts focused on the latest technologies from our leading suppliers. This program provides higher velocity learning to help minimize start-up time to quickly begin your design process utilizing the latest development tools, software and products. Check online for the latest seminar schedule.
In order to simplify the design process, Nu Horizons has created a series of application notes designed to guide engineers through the process of interfacing different devices together. Using a detailed step-by-step approach, these design guides identify key elements in the design process. Topics in the application notes are organized by design task and each topic is a stand-alone section, with a short introduction or overview, followed by the step-by-step design guidelines. All steps include a sufficient level of detail to provide the designer with relevant information to proceed quickly and easily from start to finish.
Nu Horizons offers a wide range of development / evaluation boards, tools and kits featuring the latest technology from the most trusted suppliers in the industry. Visit the development tool section of our website for a variety of solutions all aimed at providing a low-cost solution for designers to accelerate a product’s time-to-market.
http://uk.nuhorizons.com/labcam/
http://uk.nuhorizons.com/FeaturedProducts
http://uk.nuhorizons.com/seminars/index.asp
www.nuhorizons.com/olc
www.nuhorizons.com/appnotes
Application Notes
Online Learning Center
DevelopmentToolshttp://uk.nuhorizons.com/development/
Portal is a monthly publication containing new products, technologies and development tools available from Nu Horizons leading suppliers. Portal is availabe both in print and on the web. Sign up online to receive your copy, be notified of upcoming issues or to request samples of the products found inside.
Nu Horizons Online Learning Center is designed to provide a complete training experience for engineers — without having to leave the office. New supplier trainings are posted twice a month and range from new product overviews to in-depth technical training and potential design implementations. These live trainings are recorded and archived for your viewing convenience.