Upload
kristy-yeh
View
231
Download
0
Embed Size (px)
DESCRIPTION
Â
Citation preview
Digital Security System Model:DSS - 003 - NFC
NESTECH CO., LTD.
WWW.NESTECH.COM.TW
Specifications
Features Easy installation with only a Philip screwdriver. Replaceable with cylindrical locks.Multiple Users: Up to 125 User Codes (keypad programmed:50; card setting: 50; APP generated:25 access codes) , with 4-8 digits.APP function:
25 sets of access code , each one can produce 4 sets sub-access code. Anytime- can get access into anytime.Schedule- can get access into limited time.Times- up to 3 times to get access into.
Easy Operation: Convenient keypad programming or directly generate access code via APP. Simple to use.Battery life:4×AA standard 1.5V alkaline batteries.
Lock Weight 4LB
Power Source 4 AA Alkaline Batteries
Keypad Weather Resistant Keypad
Handle Reversible Lever
Door Thickness 1" to 2"
Temperature -20 to 120 degrees F (-34 to 50C) C6
Front Lock Height 6”
Front Width 2 1/2”
Back Height 6”
Back Width 2 1/2”
Key Hole to Top of Lock 4 1/2”
Working Current 50 mA
Idle Current 5 µA
Lock Back Time 5 (1 – 25) Seconds
Working Voltage 4.8-6.4V
Low Battery Warning 4.8V or lower
Keyway Schlage C6
NESTECH CO., LTD.
WWW.NESTECH.COM.TW
Battery life=up to 20.000 cycles, Recommended to change every 12 months regardless. Batteries not included.Low Battery Warning: When battery voltage gets below 4.5V,after entering a valid code the red LED will flash and lock will beep three times. Replace all 4 batteries.Emergency Battery Override If the batteries go flat you can power the lock by touching a standard battery on the terminals at the bottom of the Front Body of the lock.Security Lockout: After 4 wrong entry attempts the lock with beep and flash for 10 seconds and the inactive for 10 seconds.
DESCRIPTION
NESTECH CO., LTD.
WWW.NESTECH.COM.TW
DSS - NFC Card NFC card is solid and durable, rustless and easy to be carried, so convenient and good for users
Single latch bolt mortise
DSS - Key
DSS High Security Bump Resistant Key Cylinder
NESTECH CO., LTD.
WWW.NESTECH.COM.TW
Manual Operation Guide
General Information:
Reset: Set the lock back to manufacture default. Remove Back Body cover, press and
black Reset button 5 times (lock will beep once); it will delete all the codes, NFC Card,
and restore back to factory default setting. (See Picture)
Factory Default Setting:
Default programming code: 123456
Construction code: 0 , the construction code will be invalid, when change master
code.
Operational Options:
Key code: User Code, #
NFC card: NFC lock reader
NFC card + Keypad: NFC lock reader,
LED grow green, enter user code, #
One time service code: One time code, #
NESTECH CO., LTD.
WWW.NESTECH.COM.TW
Press 5 times Reset Button
Mechanical key : Turn the override key 90 degree clockwise, then turn the handle.
Terms:
Master code (with 4-8 digits):The master code puts thelock into a programming mode. It won’t lock/unlock thelock. When # sign is entered, the blue LED starts to flashindicating the lock is in programming mode. If more than10 seconds pass in between programming entries, thelock will return to normal operational status. Formaximum security it is necessary to change the defaultMaster Code.
Construction code: Installer code is a default temporarycode (0) for installer to test the lock. The code will bedeleted after the first new user code is added to the lock.
User code: User code is the normal code for day-to-dayoperations.
Service code:Service codes are used for a specialpurpose such as maintenance personnel or vendors.Service code only grants one time access. Total of 8 setsof service codes can be programmed to each lock.Note: Service Codes must be different from existing UserCodes.
Index #*: For each user code or NFC Card. It isassociated with a unique number; called index# (orslot#). The Index # is from 01 to 50 can be programmed on keypad.
Through card setting can produce 50 set card; APP can generate 25 set access codes, and each access code can generate 4 sub access code. Total user index is 125 that can be added to each lock, the index# ofuser code and NFC card can’t repeat. (* Please log theuser code along with its index # for deleting reference)
WWW.NESTECH.COM.TW
NESTECH CO., LTD.
Passage mode: When Passage Mode is enabled, thelock will stay in unlocked status after first valid entry.Enter a valid entry code to lock the door.
Automatic Locking:automatically locking after 5 seconds.
Lockout mode:Enabling the Lockout mode will freezethe lock at its current status (Lock or unlock), temporarilydisables all the user codes and NFC Card. Re-enter thefunction code 99 to disable the lockout mode, andresume normal operation.
Time format: 0830 = 8:30AM; 1730 = 5:30PM Schedule Date:
1=Mon, 2=Tue, 3=Wed, 4=Thu, 5=Fri, 6=Sat, 7=Sun
121130=30th, Nov, 2012
NESTECH CO., LTD.
WWW.NESTECH.COM.TW
Before using APP to generate access code, please follow the basic
setting as below:
Well done! Regarding APP operation, please download it and start your
easy management!
APP Function Detail
1Time setting
(Function Code: 88#)
Set up time(For example: Dec 1st 2015, 8:30am)
{#Master code#} + { 88 # } + { 1512010830 ###}
2Lock ID setting
(Function Code: 37#)
Set up Lock ID and Group code
{#Master code#}+ {37#}+ {Lock ID#} + {Group 0~8 ###}
Non Group setting
{#Master code#}+ {37#}+ {Lock ID#} + {0 ###}Note: Group 0 represents not belong to any Group
Group setting{#Master code#}+ {37#}+ {Lock ID#} + {1~8 ###}
Optional but recommended setting
3
Change Master code
(Function Code: 11#)
{#} + {default master code#} + {11#} + {new master code#} + {new master code###}
4
Customize access code(for visitor)
{#}+{16 digits access code#}+{your own 4-8 digits access code###}
NESTECH CO., LTD.
WWW.NESTECH.COM.TW
Card Setting Function Detail
1 Master card setting
Set up master card
1. Hold Reset button 3 seconds until long beep sound and green flash LED.2. The first NFC card used would be the Master card.
2 Add sub-cards
Add more cards. Max: 50 pcs
1. Sense Master case three times within 10 seconds until a long beep sound with green flash.
2. Put the sub-card near the lock until a short beep sound.
WWW.NESTECH.COM.TW
NESTECH CO., LTD.
Keypad Functions Detail
1 Function Code: 11#
1. How to change master code (but not delete existing users)
{#} + {default master code#} + {11#} + {new master code#} + {new master code###}
2 Function code: 22#
2. How to change master code (and delete all existing users)
{#} + {current master code#} + {22#} + {new master code#} + {new master code###}
3 Function Code: 01#
3. How to add one user code (no time restriction)
{#Master code#} + {01#} + { (01#) (02#, 03#…index#)} + {user code# # #}
4 Function Code: 01#
4. How to add one Card key (no time restriction)
{#Master code#} + {01#} + { (01#) (02#, 03#…index#)} + {touch Card # #}
5Function Code:
02#5. How to disable one user code or Card key with index #
{#Master code#} + {02#} + {index ###}
6Function Code:
03#6. Enable one user code or Card key with index #
{#Master code#} + {03#} + {index ###}
7Function Code:
04#7. Disable all user code
{#Master code#} + {04###}
8 Function Code: 33#
8. How to set up one time service code
{#Master code#} + {33#} + {service code ###}
9 Function Code: 44#
9. How to delete user code or NFC card with index #
{#Master code#} + {44# } + { (01###) (02#, 03#…index#)}
Keypad Functions Detail
NESTECH CO., LTD.
WWW.NESTECH.COM.TW
User Information: Example
10 Function Code: 88#
10. Set up time(For example: Dec 1st 2015, 8:30am)
{#Master code#} + { 88 # } + { 1512010830 ###}
11 Function Code: 37#
11. Set up Lock ID and Group code
{#Master code#}+ {37#}+ {Lock ID#} + {Group 0~8 #}
Non Group setting
{#Master code#}+ {37#}+ {Lock ID#} + {0 ###}
Group setting {#Master code#}+ {37#}+ {Lock ID#} + {1~8 ###}
Keypad Functions DetailKeypad Functions Detail
Default Master Programming Code
123456Construction code: 0 #
New User Information
No. Users
001 J Blow
002 B Smith
003 A Man
… Etc
New Master Code
No. User No. User
001 010
002 011
003 012
004 013
005 014
006 015
007 016
008 017
009 …