NEW SMYRNA CAMPUS BUILDING 1 AND BUILDING … 16-008 Addendum.pdfaddendum 1 october 23, 2015 new smyrna campus building 1 and building 2 remodel efis # 2639-1 project number: 15008.02

ADDENDUM 1OCTOBER 23, 2015

NEW SMYRNA CAMPUSBUILDING 1 AND BUILDING 2 REMODEL

EFIS # 2639-1PROJECT NUMBER: 15008.02

RLF Architects4750 New Broad StreetOrlando, Florida 32814Telephone (407) 730-8600Telefax (407) 730 3603License # AAC000564

TO THE BEST OF MY KNOWLEDGE, THESE DRAWINGS ARE COMPLETE ANDCOMPLY WITH THE FLORIDA BUILDING CODE

BUILDING CODES2014 FLORIDA FIRE PREVENTION CODE (FFPC)2014 STATE REQUIREMENTS FOR EDUCATIONAL FACILITIES (SREF)2014 FLORIDA BUILDING CODE EXISTING BUILDING (FBC),2014 FLORIDA BUILDING CODE ACCESSIBILITY (FBC)2014 FLORIDA BUILDING CODE ENERGY CONSERVATION (FBC)2011 NATIONAL ELECTRICAL CODE2014 FLORIDA BUILDING CODE MECHANICAL2014 FLORIDA BUILDING CODE PLUMBING

CLASSIFICATION OF WORK – OCCUPANCYEXISTING BUSINESS ALTERATION – LEVEL 2EXISTING CONSTRUCTION TYPE II-B

NON-SPRINKLERED

CLASSIFICATION BUSINESS GROUP B:

OCCUPANT LOAD OVER 50 REQUIRES A SECOND MEANS OF EGRESS. ROOMSTHAT EXCEEDS 50 HAVE TWO MEANS OF EGRESS.

PROJECT NARRATIVETHE PROJECT REPRESENTED IN THESE CONSTRUCTION DOCUMENTSCONSISTS OF THE RENOVATION OF THE ROOMS HIGHLIGHTED ON SHEET GI100.WORK INCLUDES REMOVAL AND REPLACEMENT OF INTERIOR FINISHES,REMOVAL OF WALL PARTITIONS AS INDICATED, LIGHT FIXTURE REPLACEMENTAND ELECTRICAL INFRASTRUCTURE / RETROFIT, MECHANICAL DIFFUSERREPLACEMENT, PLUMBING COORDINATION, THE EXPSOURE OF EXTERIORWINDOWS IN AREAS INDICATED AND THE REMOVAL OF INTERIOR ANDEXTERIOR DOORS.

RENOVATION WORK DOES NOT AFFECT ANY EXIT ACCESS CORRIDORS

GENERAL

Sheet Number Sheet Name

GI001 COVER SHEETGI100 ARCHITECTURAL ABBREVIATIONS AND SYMBOLSGI101 ARCHITECTURAL SPECIFICATIONSGI102 FIRE RATED PENETRATIONSB1-GC111 BUILDING 1 LIFE SAFETY PLANB2-GC111 BUILDING 2 LIFE SAFETY PLAN

940 10TH STREETNEW SMYRNA BEACH, FL. 32168

ELECTRICAL


EG001 ELECTRICAL SYMBOLS LEGENDEG002 ELECTRICAL SPECIFICATIONSB1-ED101 BUILDING 1 ELECTRICAL DEMOLITION PLANB1-ED201 BUILDING 1 LIGHTING DEMOLITION PLANB1-EP101 BUILDING 1 POWER AND SYSTEMS PLANB1-EL101 BUILDING 1 LIGHTING PLANB2-ED101 BUILDING 2 ELECTRICAL DEMOLITION PLANB2-ED201 BUILDING 2 LIGHTING DEMOLITION PLANB2-EP101 BUILDING 2 POWER AND SYSTEMS PLANB2-EL101 BUILDING 2 LIGHTING PLANEL601 LIGHTING CONTROLS DIAGRAMSEP601 SINGLE LINE DIAGRAMSEP701 ELECTRICAL PANEL SCHEDULES

INDEX OF DRAWINGS

VICINITY MAP

N

MECHANICAL


MH001 MECHANICAL SYMBOLS AND ABBREVIATIONSMH002 MECHANICAL SPECIFICATIONSB1-MD101 BUILDING 1 FLOOR PLAN - HVAC - DEMOB1-MH101 BUILDING 1 FLOOR PLAN - HVACB2-MD101 BUILDING 2 FLOOR PLAN - HVAC - DEMOB2-MH101 BUILDING 2 FLOOR PLAN - HVACMH501 MECHANICAL DETAILSMH801 MECHANICAL SCHEDULES

PLUMBING


PL001 PLUMBING SYMBOLS AND ABBREVIATIONSPL002 PLUMBING SPECIFICATIONSB1-PL101 BUILDING 1 PLUMBING PLAN

CODE INFORMATION

10TH STREET

NORTH OLD COUNTY ROAD

HIGHWAY US-1

ARCHITECTURE


B1-AE101 BUILDING 1 COMPOSITE FLOOR PLAN EXISTINGB1-AD401 BUILDING 1 ENLARGED DEMOLITION PLANB1-AE201 BUILDING 1 SECTIONS, ELEVATIONS AND DETAILSB1-AE401 BUILDING 1 ENLARGED FLOOR PLANB1-AE410 BUILDING 1 REFLECTED CEILING PLANB2-AE101 BUILDING 2 COMPOSITE FLOOR PLAN EXISTINGB2-AD401 BUILDING 2 ENLARGED DEMOLITION PLANB2-AE201 BUILDING 2 SECTIONS, ELEVATIONS AND DETAILSB2-AE401 BUILDING 2 ENLARGED FLOOR PLANB2-AE410 BUILDING 2 REFLECTED CEILING PLAN

BUILDING 1

BUILDING 2

1

1

1

1

2

2

2

S

CEILING TYPES

MECHANICAL SYMBOLS

ELECTRICAL SYMBOLS

FIRE ALARM SYMBOLS

CEILING LEGEND

INTERIOR: GYPSUM BOARD CEILING SYSTEM

ACOUSTICAL CEILING TILE2'-0" X 2'-0"

CEILING ACCESS PANEL.

LIGHT FIXTURE

EXIT LIGHTS

SPEAKERSENSOR

SUPPLY AIR DIFFUSER

TRANSFER AIR REGISTER / GRILLE

RETURN AIR REGISTER / GRILLE

EXHAUST AIR REGISTER

CEILING HOSTED STROBE LIGHT

SMOKE DETECTOR

CCTV CAMERA

00

00

A1011

A101

1A101

SIM

0/0" = 1'-0"00 VIEW NAME

1 Ref

1

Ref

1 Ref

1

Ref

GENERAL SYMBOLS

INTERIOR ELEVATION REFERENCE

SECTION REFERENCE

REFERENCE FOR DETAIL OR ENLARGED PLAN

DETAIL / SECTION NUMBER

SHEET NUMBER

LEADER OR NOTATION

REVISION IDENTIFIER

KEY NOTE

CENTERLINE

ROOM NUMBERROOM NAME

1239STORAGE

092900.A01 MATERIAL NOTES

INDEPENDANT SUFFIX MATERIAL ORNOTE SPECIFIER FOR CONDOC LISTSPECIFICATION SECTION PREFIX

B1-AE100 SHEET NUMBER

SHEET SEQUENCE NUMBERSHEET TYPEDISCIPLINE DESIGNATOR

N TRUE NORTH

BUILDING NUMBER

NBUILDING 1STUDENT SERVICES

BUILDING 2ACADEMIC HALL

1" = 20' GRAPHIC SCALE

20'0 60'40' 80'10'

111CLASSROOM

149CLASSROOM

150CLASSROOM

148OFFICE

CLASSROOM139A

CLASSROOM139B

CLASSROOM135

STORAGE112

COMMS136

COMPUTER LAB101

COMPUTER LAB102

COMPUTER LAB103

LOUNGE116

OFFICE115

OFFICE114

MULTI-PURPOSE ROOM109

OFFICE113

112A

123

138

137

111 112110

117

118

120

119

124125

105

149149A

146

147A

148A

142

143

144

141

145

139

140

133

136

134

137

165

166100

150

152

153 151

106

126127128129

107

132 131 130

130A108

114

116

117

118

119

120

121

122

151B

126

127

128

129

152A130

131

132

133

134

151D

142140

141143

144

146

151 151E

101

101A

102

104A

104 103103A

151F

105

106

108

109

109A109B

110 110A

110B

151A

151C

124

125A

102A

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions

sheet title/contents

of

drawing number

Telefax (407) 730-3603

License NumberLicense Number

project title & owner's name

EBAA

0000629C000564

Telephone

Interior Design

4750 New Broad Street

ROGERS, LOVELOCK & FRITZ, INC.

Orlando, Florida 32814(407) 730-8600

EngineeringArchitecture

www.rlfarchitects.com

XXX

OCTOBER 23, 2015

IF THIS SHEET MEASURES LESS THAN 30" x 42", IT HAS BEEN REDUCED

consultant

ADDENDUM 1

NEW SMYRNA CAMPUS

AR OF RECORD AR0015014

10/23

/2015

1:10

:14 P

M

GI100

ARCHITECTURALABBREVIATIONSAND SYMBOLS

CME

EHB

GENERAL ABBREVIATIONS

KkPA KILOPASCAL

LLB POUNDLF LINEAR FEETLL ANGLE

Mm METERSMAX MAXIMUMMFR MANUFACTURERMIN MINIMUMMISC MISCELLANEOUSmm MILLIMETERSMO MASONRY OPENING

NN NORTHNA NOT APPLICABLENIC NOT IN CONTRACTNO NUMBERNOM NOMINALNTS NOT TO SCALE

OOC ON CENTEROD OUTSIDE DIAMETEROPH OPPOSITE HANDOPNG OPENING

PPL PLATEPLAM PLASTIC LAMINATEPR PAIRPSF POUNDS per SQUARE FOOTPSI POUNDS per SQUARE INCHPT PRESSURE TREATED / PAINTPTS PNEUMATIC TUBE STATION

QQTR QUARTERQTY QUANTITY

RR RISER / RADIUSRAL FEDERAL COLOR PALETTERCP REFLECTED CEILING PLANRE RESIDENT ENGINEERRENO RENOVATE / RENOVATIONREQ REQUIREDRO ROUGH OPENING

SS SOUTH / SINKSF SQUARE FEETSIM SIMILARSJ SEISMIC JOINTSPECS SPECIFICATIONSQ SQUARESST STAINLESS STEELST STAINEDSTC SOUND TRANSMISSION CLASSSTL STEELSWGR SWITCHGEAR

TT TREADTEL TELEPHONETEMP TEMPERATURE / TEMPORARYTHD THRESHOLDTHK THICKNESSTHRU THROUGHTLT TOILETTO TOP OFTOC TOP OF CONCRETE (CURB)TOF TOP OF FOOTINGTOM TOP OF MASONRYTOP TOP OF PRECASTTOS TOP OF STEELTYP TYPICAL

UU HEAT TRANSFER COEFFICIENTU/C/B UNDER COUNTER BASEUC UNDERCUTUL UNDERWRITERS LABORATORYUNO UNLESS NOTED OTHERWISEUR URINAL

VV VACUUMVAR VARIESVCT VINYL COMPOSITION TILEVERT VERTICALVTR VENT THRU ROOF

WW WEST / WAITW WIDTH / WIDE FLANGEW/ WITHW/O WITHOUTWD WOODWH WALL HUNG / WATER HEATERWP WATERPROOF / WORKING UNITWT WEIGHTWWF WELDED WIRE FABRIC

GENERAL ABBREVIATIONS# AND SYMBOLS# NUMBER / POUND& AND@ AT

AA AIRA/C AIR CONDITIONEDA/E ARCHITECT-ENGINEERACT ACOUSTICAL CEILING TILEAD AREA DRAINADA AMERICANS WITH DISABILITIES ACTAFF ABOVE FINISHED FLOORAHJ AUTHORITY HAVING JURISDICTIONAHU AIR HANDLING UNITALT ALTERNATEALUM ALUMINUMAMP AMPEREAO ACCESS OPENINGAPPROX APPROXIMATELYARCH ARCHITECTURAL

BBAL BALANCEBD BOARDBKOP BACK OF PRECAST / BACK OF PANELBLDG BUILDINGBLK BLANKBM BEAMBO BOTTOM OFBOP BOTTOM OF PRECASTBOS BOTTOM OF STEELBRG BEARINGBTUH BRITISH THERMO UNIT / HOUR

CCCT CUBICLE CURTAIN TRACKCG CORNER GUARDCJ CONTROL / CONSTRUCTION JOINTCL CENTER LINECLG CEILINGCLL COLUMN LINECLR CLEARcm CENTIMETERCMU CONCRETE MASONRY UNITCO CONTRACTING OFFICERCO2 CARBON DIOXIDECONC CONCRETECONT CONTINUED / CONTINUOUSCOORD COORDINATECTJ CONTRACTION JOINTCTR CENTER

DD DEEP / DEPTHdBA UNIT OF SOUNDDEG DEGREEDIA DIAMETERDIMS DIMENSIONSDN DOWNDR DOORDWG DRAWING(S)DWR DRAWER

EEA EACHEE EACH ENDEJ EXPANSION JOINTEL ELEVATIONEOS EDGE OF SLABEQ EQUALETC ET CETERAETR EXISTING TO REMAINEWC ELECTRIC WATER COOLEREWS EYE WASH STATIONEXIST EXISTING

FF FILLERFAX FACSIMILEFE FIRE EXTINGUISHERFEC FIRE EXTINGUISHER CABINETFF FINISHED FLOORFHC FIRE HOSE CABINETFIN FINISHEDFLR FLOORFO FACE OFFOS FACE OF SLAB / FACE OF STUDFT FOOT / FEET

GG GASGA GAGEGALV GALVANIZEDGB GRAB BARGC GENERAL CONTRACTORGEM GLOBAL ELECTRIC MOTORCARS

HH HIGHHC HANDICAPHDWR HARDWAREHE HORIZONTAL EXITHM HOLLOW METALHR HOUR

IIC INTERCOMID INSIDE DIAMETERIN INCH(ES)INFO INFORMATION

JJT JOINT

1" = 20'-0"1 OVERALL SITE

No. Description Date

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:10

:21 P

M

GI101

ARCHITECTURALSPECIFICATIONS

CME

EHB

SECTION 06 41 66 – PLASTIC LAMINATE FACED CABINETSA. Quality Assurance: Fabricator qualifications; certified participant in AWI’s Quality Certification Program.

B. Plastic Laminate-Faced Cabinets1. Grade: Premium2. Type of Construction: Frameless3. Cabinet and Door Fronts: Flush Overlay4. Laminate Cladding for Exposed Surfaces:

a. Horizontal Surfaces: HGL (Horizontal Grade Laminate); “General Purpose Type, 1.0 mm nominal thickness, countertop surfaces.”

b. Postformed Surfaces: HGP (Horizontal, General Purpose Post-forming); “Post-forming Type, 1.0 mm nominal thickness, post-formed countertop surfaces.”c. Vertical Surfaces: VGS (Vertical, Grade Laminate); “General Purpose Type, 0.7 mm nominal thickness, vertical

surfaces.”5. Cabinet Interior: Same as Exterior6. Laminate And Color: Basis of Design: As indicated on the drawings

C. Cabinet Hardware1. Hinges: Frameless Concealed2. Pulls: Wire3. Cabinet Hardware Finish: Stainless Steel, Satin

SECTION 09 22 16 - NON-STRUCTURAL METAL FRAMINGA. Fire-Test-Response Characteristics: For fire-resistance-rated assemblies that incorporate non-load-baearing steel framing,

provide materails and construction identical to those tested in assembly indicated according to ASTM E 119 by an indpendent testing agency.

B. Framing Members, General: Comply with ASTM C 754 for conditions indicated.1. Steel Sheet Components: Comply with ASTM C 645 requirements for metal, unless otherwise specified.2. Protective Coating: ASTM A 653/A 653M, G40, unless otherwise specified

C. Steel Studs and Runners: ASTM C 645, excluding use of dimpled members.1. Minimum Base-Metal Thickness: 0.033 inch, unless otherwise indicated.2. Depth: 3-5/8 inches unless otherwise indicated.

D. Slip-Type Head Joints: Where indicated, provide one of the following:1. Single Long-Leg Runner System: ASTM C 645 top runner with 2-inch- deep flanges in thickness not less than indicated for

studs, installed with studs friction fit into top runner and with continuous bridging located within 12 inches of the top of studs to provide lateralbracing.

2. Double-Runner System: ASTM C 645 top runners, inside runner with 2-inch- deep flanges in thickness not less than indicated for studs and fastened to studs, and outer runner sized to friction fit inside runner.

3. Deflection Track: Steel sheet top runner manufactured to prevent cracking of finishes applied to interior partition framing resulting from deflection of structure above; in thickness not less than indicated for studs and in width to accommodate depth of studs.

E. Firestop Tracks: Top runner manufactured to allow partition heads to expand and contract with movement of the structure while maintaining continuity of fire-resistance-rated assembly indicated; in thickness not less than indicated for studs and in width to accommodate depth of studs.

F. Flat Strap and Backing Plate: Steel sheet for blocking and bracing in length and width as needed to suit condition.1. Minimum Base-Metal Thickness: 0.033 inch, unless otherwise indicated.

G. Cold-Rolled Channel Bridging: 0.0538-inch bare-steel thickness, with minimum 1/2-inch- wide flanges.1. Depth: 1-1/2 inches.2. Clip Angle: Not less than 1-1/2 by 1-1/2 inches, 0.068-inch- thick, galvanized steel.

H. Hat-Shaped, Rigid Furring Channels: ASTM C 645.1. Minimum Base Metal Thickness: 0.0179 inch.2. Depth: 7/8 inch.

I. Installation Standard: ASTM C 754, except comply with framing sizes and spacing indicated.1. Gypsum Board Assemblies: Also comply with requirements in ASTM C 840 that apply to framing installation.2. Install studs so flanges within framing system point in same direction.

a. Space studs as follows:1)Single-Layer Application: 16 inches o.c., unless otherwise indicated.2)Multilayer Application: 16 inches o.c., unless othewise indicated.

SECTION 09 29 00 - GYPSUM BOARDA. Fire-Resistance-Rated Assemblies: For fire-resistance-rated assemblies, provide materials and construction identical to those tested in assembly indicated according to ASTM E 119 by an independent testing agency.

B. General: Complying with ASTM C 36/C 36M or ASTM C 1396/C 1396M, as applicable to type of gypsum board indicated and whichever is more stringent.

C. Type X:1. Thickness: 5/8 inch.2. Long Edges: Tapered and featured (rounded or beveled) for prefilling.

D. Ceiling Type: Manufactured to have more sag resistance than regular-type gypsum board.1. Thickness: Minimum 1/2 inch, Type X.2. Long Edges: Tapered.

E. Moisture- and Mold-Resistant Type: With moisture- and mold-resistant core and surfaces.1. Product: Subject to compliance with requirements; provide “Dens Armor Plus Fireguard Paperless Interior Panel” by G-P

Gypsum.2. Core: 5/8 inch, Type X.3. Long Edges: Tapered.

F. Interior Trim: ASTM C 1047.1. Material: Galvanized or aluminum-coated steel sheet or rolled zinc.2. Shapes:

a. Cornerbead.b. LC-Bead: J-shaped; exposed long flange receives joint compound.c. L-Bead: L-shaped; exposed long flange receives joint compound.d. U-Bead: J-shaped; exposed short flange does not receive joint compound.e. Expansion (control) joint.

G. Joint Materials: Comply with ASTM C 475/C 475M.1. Joint Tape:

a. Interior Gypsum Wallboard: Paper.2. Joint Compound for Interior Gypsum Wallboard and Gypsum Base for Plaster: For each coat use formulation that is

compatible with other compounds applied on previous or for successive coats.a. Prefilling: At open joints, rounded or beveled panel edges, and damaged surface areas, use setting-type taping compound.b. Embedding and First Coat: For embedding tape and first coat on joints, fasteners, and trim flanges, use drying-type, all-purpose compound.c. Fill Coat: For second coat, use drying-type, all-purpose compound.d. Finish Coat: For third coat, use setting-type, sandable topping compound.

H. Steel Drill Screws: ASTM C 1002, unless otherwise indicated.1. Use screws complying with ASTM C 954 for fastening panels to steel members from 0.033 to 0.112 inch thick.

I. Applying and Finishing Panels: Comply with ASTM C 840.

J. Installing Trim Accessories: For trim with back flanges intended for fasteners, attach to framing with same fasteners used for panels. Otherwise, attach trim according to manufacturer's written instructions.

K. Control Joints: Install control joints according to ASTM C 840 and as indicated.

L.Interior Trim: Install in the following locations:1. Cornerbead: Use at outside corners.2. LC-Bead: Use at exposed panel edges.3. L-Bead: Use where indicated.4. U-Bead: Use at exposed panel edges.

M. Gypsum Board Finish Levels: Finish panels to levels indicated below and according to ASTM C 840:1. Level 1: Ceiling plenum areas, concealed areas, and where indicated.2. Level 2: Panels that are substrate for tile and panels that are substrate for acoustical tile.3. Level 3: In mechanical and electrical rooms.4. Level 4: At panel surfaces that will be exposed to view.

SECTION 09 51 23 – ACOUSTICAL TILE CEILINGSA. Standards:

1. Products: The Owner will only accept suspended ceiling acoustical ceiling panels and suspension systems manufacturedby Rockfon, LLC.

2. Preparation and Workmanship: Comply with requirements in "Rockfon Specification Manual" for products indicated.

B. Acoustical Ceiling Tile Material: Basis of Design: Rockfon Tropic1. ASTM E1264 Classification: Type XX, Pattern G.2. Edges: Square3. Size: 24 by 24 inches4. NRC: 0.90.5. CAC: 22.6. Fire Class: Class A.7. Fire Performance UL 723 (ASTM E 84) Flame Spread / Smoke Developed: 0/5.8. Light Reflectance: 0.86.9. Recycled Content: Up to 36 percent.

SECTION 09 51 23 – ACOUSTICAL TILE CEILINGS CONTINUEDC. Suspension System: Suspension system manufacturer’s standard direct-hung metal suspension system and attachment devices complying with project requirements

and applicable building codes and regulations applicable at the location of the project and as follows:1. Structural Classification: Intermediate duty system, ASTM A 635.2. Face Design: Flat, flush.3. Cap Material: Steel cold-rolled sheet.4. Cap Finish: Factory painted white color

D. Installation: Install products in accordance with manufacturer’s written instructions and in proper relationship with adjacent construction, including the following:1. Install hangers plumb and free from contact with insulation or other objects within ceiling plenum that are not part of supporting structure or of ceiling suspension

system.2. Clean exposed surfaces in accordance with manufacturer’s written instructions. Touch-up, repair or replace damaged units until satisfactory results are

obtained.

SECTION 09 65 13 - RESILIENT BASE AND ACCESSORIESA. Thermoset-Rubber Base

1. Product Standard: ASTM 1861, Type TS (Rubber, Vulcanized Thermoset), Group 1 (Solid Homogeneous)2. Style and Location:

a. Style B, Coved: Provide in areas with carpet.3. Thickness: 0.125 inch (3.2 mm).4. Height: Provide 4" or 6" high rubber base to match existing conditions.5. Length: Coils in manufacturer’s standard length6. Outside Corners: Job Formed7. Inside Corners: Job Formed8. Colors: Owner to confirm color selection

B. Installation Materials1. Adhesives: Water-resistant type recommended by resilient-product manufacturer for resilient products and substrate conditions indicated.

C. Execution:1. Prepare substrates according to manufacturer's written instructions to ensure adhesion of resilient products.2. Do not install resilient products until they are the same temperature as the space where they are to be installed.3. Immediately before installation, sweep and vacuum clean substrates to be covered by resilient products.

D. Resilient Base Installation1. Comply with manufacturer's written instructions for installing resilient base.2. Apply resilient base to walls, columns, pilasters, casework and cabinets in toe spaces, and other permanent fixtures in rooms and areas where base is required.3. Install resilient base in lengths as long as practical without gaps at seams and with tops of adjacent pieces aligned.4. Tightly adhere resilient base to substrate throughout length of each piece, with base in continuous contact with horizontal and vertical substrates.5. Do not stretch resilient base during installation.6. Job Formed Corners:

a.Outside Corners: Use straight pieces of maximum lengths possible and form with returns not less than 3 inches (76 mm) in length.1) Form without producing discoloration (whitening) at bends.

b.Inside Corners: Use straight pieces of maximum lengths possible and form with returns not less than 3 inches (76 mm) in length.1) Miter or cope corners to minimize open joints.

7. Cleaning And Protectiona. Comply with manufacturer's written instructions for cleaning and protecting resilient products.b. Cover resilient products subject to wear and foot traffic until Substantial Completion.

SECTION 09 65 19 – RESILIENT TILE FLOORINGA. Standards:

1. Products: Basis of Design: Armstrong Flooring, Standard Excelon Imperial Texture2. Preparation and Workmanship: Comply with requirements of Manufacturer's written installation instructions for preparing substrates indicated to receive resilient

flooring.3. Testing: Critical Radiant FLux Classification: Class 1, not less than 0.45 W/sq.cm

B. Material Identification:1. Tile Standard: ASTM F 1066, Class 2, through pattern tile.2. Wear Surface: Smooth2. Thickness: 0.125 inch3. Size: 12x12 inch4. Pattern and Color: Owner to confirm color selection

C. Installation Materials:1. Trowelable Leveling and Patching Compounds: Latex-modified, hydraulic-cement-based formulation provided or recommended by resilient tile manufacturer.2. Adhesives: Water-resistant, mildew-resistant, nonstaining, pressure-sensitive type to suit products and subfloor conditions indicated, that comply with flammability

requirements for resilient tile, and are recommended by resilient tile flooring manufacturer.3. Floor Polish: Provide proteective, liquid floor polish products recommended by the floor tile manufacturer.

F. Installation Method:

1. Comply with manufacturer's written instructions for installation floor tile.2. Lay out floor tile from center marks established with principle walls, discounting minor offsets, so tiles at opposite edges of room are of equal width. Adjust as

necessary to avoid using cutwidths that equal less than one-half at perimeter.

G. Examination:1. Examine substrates, areas and conditions, with Installer present for compliance with requirements for maximum moisture content, alkalinity range, installation

olerances and other conditions affecting the carpet tile performance.2. Examine tile for type, color, pattern and potential defects.3. Proceed with installation only after unsatisfactory conditions have been corrected.

H. Preparation:1. Concrete Substrates: Remove existing flooring materials, coatings, including curing compounds, and other substances that are incompatible with adhesives and

that contain soap, wax, oil, or silicone, without using solvents. Use mechanical methods Recommended in writing by adhesive and carpet tile manufacturers.2. Use trowelable leveling and patching compounds, according to manufacturer's written instructions, to fill cracks, holes, depressions, and protrusions in substrates.

Fill or level cracks, holes and depressions 1/8 inch wide or wider, and protrusions more than 1/32 inch, unless more stringent requirements are required by adhesive and carpet tile manufacturers’ written instructions.

I. Cleaning And Protection:1. Remove excess adhesive and other surface blemishes, as recommended by carpet tile manufacturer.2. Damp-mop surfaces to remove marks and soils.3. Apply floor polish on clean floor tile surfaces.4. Protect floor tile against damage from construction operations and placement of equipment during the remainder of the construction period.

SECTION 09 68 13 – CARPET TILEA. Standards:

1. Products: Basis of Design: Patcraft Carpet.2. Preparation and Workmanship: Comply with requirements of CRI’s “Carpet Installation Standards and with Patcraft Carpet written installation instructions for

preparing substrates indicated to receive carpet tile.3. Testing:

a.Radiant Panel ASTM E648-08: Class 1b.Smoke Density ASTM E662-09: Passed 450 or less

4. Warranty: Lifetime Commercial Limited

B. Material Identification:1. Construction: Multi-level Pattern Loop2. Pattern: Owner to confirm pattern3. Color: Owner to confirm final color selection4. Fiber: Eco Solution Q. Nylon; 100% Solution Dyed Nylon5. Tufted Weight: 186. Size: 24”x24”7. Primary Backing: Non Woven Synthetic8. Secondary Backing: Ecoworx Tile9. Applied Treatment: SSP Shaw Soil Protection

C. Installation Materials:1. Trowelable Leveling and Patching Compounds: Latex-modified, hydraulic-cement-based formulation provided or recommended by carpet tile manufacturer.2. Adhesives: Water-resistant, mildew-resistant, nonstaining, pressure-sensitive type to suit products and subfloor conditions indicated, that comply

with flammability requirements for installed carpet tile, and are recommended by carpet tile anufacturer for releasable installation

D. Installation Method:1. Installation direction to be confirmed with Owner once Final Pattern and Color are determined.2. Install per Manufacturer's written instructions and requirements.

E. Examination:1. Examine substrates, areas and conditions, with Installer present for compliance with requirements for maximum moisture content, alkalinity range,

installation tolerances and other conditions affecting the carpet tile performance.2. Examine carpet tile for type, color, pattern and potential defects.3. Proceed with installation only after unsatisfactory conditions have been corrected.

F. Preparation:1. Concrete Substrates: Remove existing flooring materials, coatings, including curing compounds, and other substances that are incompatible with adhesives and

that contain soap, wax, oil, or silicone, without using solvents. Use mechanical methods recommended in writing by adhesive and carpet tile manufacturers.2. Use trowelable leveling and patching compounds, according to manufacturer's written instructions, to fill cracks, holes, depressions, and protrusions in substrates.

Fill or level cracks, holes and depressions 1/8 inch wide or wider, and protrusions more than 1/32 inch, unless more stringent requirements are required by adhesive and carpet tile manufacturers’ written instructions.

H. Cleaning And Protection:1. Remove excess adhesive and other surface blemishes, as recommended by carpet tile manufacturer.2. Remove yarns that protrude from the carpet tile surface3. Vacuum carpet tile4. Protect carpet tile against damage from construction operations and placement of equipment during the remainder of the construction period.

SECTION 09 72 00 - WALLCOVERING (ADD ALTERNATE FOR COST)A. Standards:

1. Products: Basis of Design: Guilford of Maine.2. Use: For the purpose to re-upholster existing acoustical wall panels and operable partitions.3. Fire Test: Surface-Burning Characteristic; Comply with ASTM E-84 testing by a qualified testing agency. Identify products with appropriate markings

of applicable testing agency.a. Flame Spread: 25 or lessb. Smoke-Developed Index: 50 or less

4. Installer Qualifications: An authorized representative who is trained & approved by the existing installed product manufacturer installed on the campus.

B. Material Identification:1. Construction: 79% Post-consumer recycled polyester, 21% pre-consumer recycled polyester.2. Pattern / Color: Basis of Desing as indicated on the drawings.

a. Owner to confirm final pattern and color selection3. Total Weight: 14.0 +/- 1.0 oz./lin. yd.4. Repeat: None5. Width: 66" minimum useable

C. Preparation / Installation:1. Measure each existing wall panel and operable wall panel and establish layout panel and joint dimensions. Before installation allow fabric to adjust

and become stable in spaces where it will be installed according to wall panel / operable wall panel manufacturer's instructions.2. Install fabric system level, plumb and with tight fit, unless otherwise indicated, true in plane and with the fabric square to the grain.3. Install fabric with patterns or directional weaves so pattern or weave aligns with adjacent panel. Fabric seams are not permitted.4. Stretch and secure fabric to frame edges and so frame and frame attachment method are concealed by fabric unless otherwise noted. Stretch fabric

tightly and square without puckers, ripples, or distortions. Acclimatize and restretch if required. Repair distortions, wrinkles and sagging.5. Edge straightness plus or minus 1/16 inch in 48 inches6. Variation from Level and Plumb plus or minus 1/16 inch in 48 inches.

SECTION 09 91 23 - INTERIOR PAINTINGA. Standards:

1. Products: Basis of Design: Sherwin Williams.2. Preparation and Workmanship: Comply with requirements in "Sherwin Williams Specification Manual" for products and paint systems indicated.

B. Material Compatibility:1. Provide materials for use within each paint system that are compatible with one another and substrates indicated, under conditions of service and

application as demonstrated by manufacturer, based on testing and field experience.2. For each coat in a paint system, provide products recommended in writing by Sherwin Williams for use in paint system and on substrate indicated.

C. VOC Content of Field-Applied Interior Paints and Coatings: Provide products that comply with the following limits for VOC content, exclusive of colorants added to a tint base, when calculated according to 40 CFR 59, Subpart D (EPA Method 24); these requirements do not apply to paints and coatings that

are applied in a fabrication or finishing shop:1. Flat Paints, Coatings, and Primers: VOC content of not more than 50 g/L.2. Nonflat Paints, Coatings, and Primers: VOC content of not more than 150 g/L.3. Anti-Corrosive and Anti-Rust Paints Applied to Ferrous Metals: VOC not more than 250 g/L.4. Nonflat Topcoat Paints: VOC content of not more than 150 g/L.

D. Colors: General paint colors and accent colors to be selected by the Owner.1. Finish: Eggshell

E. Interior Latex Block Filler:1. VOC Content: Minimum E Range of E1.

F. Interior Latex Primer/Sealer:1. VOC Content: Minimum E Range of E1.

G. Alkyd Anticorrosive Metal Primer:1. VOC Content: E Range of E2.

H. Interior Alkyd (Eggshell):1. VOC Content: E Range of E2.

I. Institutional Low-Odor/VOC Latex (Eggshell):1. VOC Content: E Range of E3.

J.Maximum Moisture Content of Substrates: When measured with an electronic moisture meter as follows:1. Concrete: 12 percent.2. Masonry (Clay and CMU): 12 percent.3. Gypsum Board: 12 percent.4. Begin coating application only after unsatisfactory conditions have been corrected and surfaces are dry.

a. Beginning coating application constitutes Contractor's acceptance of substrates and conditions.

K. Application: Comply with manufacturer's written instructions and recommendations in "Sherwin Williams Specification Manual" applicable to substratesindicated.

L.Gypsum Board Substrates:1. Institutional Low-Odor/VOC Latex System:

a. Prime Coat: Prerite 200 Latex Primer B28W200b. Intermediate Coat: Pro Mar 200 Latex Egg-Shell B20W251c. Topcoat: Pro Mar 200 Latex Egg-Shell B20W latex (eggshell or flat, as applicable to match existing adjacent surfaces).

2. Alkyd System:a. Prime Coat: Alkyd anticorrosive metal primer.b. Intermediate Coat: Interior alkyd matching topcoat.c. Topcoat: Interior alkyd eggshell.

M. Existing Hollow Metal Door Frames: Prepare and Clean for new coatings:1. First Coat: Kem Kromik Universal Metal Primer B50 series2. Second Coat:Pro Mar 200 Alkyd Semi-Gloss B34W2003. Third Coat: Pro Mar 200 Alkyd Semi-Gloss B34W200

SECTION 10 21 23 - CUBICLE CURTAIN TRACK & CURTAINA. Standards:

1. Products: The Owner will accept cubicle curtain track products that meet the performance specification outlined. Provide cubicle curtains as indicatedon the drawings.

2. Publications:a. American Society for Testing and Materials (ASTM) B221-08; Aluminum and Aluminum-Alloy Extruded bars, Rods, Wire, Shapes, and Tubes.b. The National Association of Architectural Metal Manufacturers (NAAMM) AMP 500 Series; Metal Finishes Manual

B. Cubicle Curtain Tracks:1. Channel Tracks: Extruded aluminum, ASTM B221, alloy 6063, temper T5 or T6, channel shaped, with smooth inside raceway for curtain carriers.

a. Surface Mounted JSN A5180A: Size and configuration as indicated om drawings. Use for typical cubicle curtains (JSN A5180B).2. Curtain Carriers: Nylon or delrin carriers, with either nylon or delrin wheels on metal, delrin, or nylon axles. Equip each carrier with either stainless

steel, chromium plated brass or steel hooks with swivel, or nickel chromium plated brass or stainless steel bead chain and hook assembly or delrincarriers may have molded on delrin hooks. Hook for bead chain may be the same material and finish as the bead chain or may be chromium plated

steel. Provide 2.2 carriers for every 12 inches of each section of each track length, plus one additional carrier.3. End Stop Connectors. Ceiling Flanges and Other Accessories: Fabricate from the same material with the same finish as the tracks or from nylon.4. Hangers and Fittings: Fabricate from the same material with the same finish as the tracks. Hangers may be round or square for channel tracks and

round for tubular tracks. Design fittings to be compatible with design of tracks and to safely transmit the track load to the hangers.5. At the end of each section of track, make provisions for insertion and removal of carriers. Design to prevent accidental removal of the carrier. Any

operating mechanism shall be removable with common tools.

C. Cubicle Curtain Material:1. First quality, imperfections or seconds are not acceptable.2. Color and Pattern Basis of Design, as indicated on the drawings. Final Pattern and Color to be selected by the Owner.3. Mesh Top: Fire retardant and antimicrobial, No. 50, 100% Dacron Polyester with Visa XL finish, not less than 20 inches wide mesh top. Color to match

cubicle curtain.4. Grommets: Two-piece, rolled-edge, rustproof, nickel-plated brass; spaced not more than 6-inches on center; machined into top hem.5. Cubicle Curtain (A5180B): 97% FR Polyester, 3% X-Static silver antimicrobial fiber.

a. Width: 72 inchesb. Repeat: Approximately 27" vertical

6. Fabrication:a. Width: Equal to track length from which the curtain is hung plus 10 percent added fullness, but not less than 12" added fullness.b. Length: Equal to the floor to ceiling height, minus depth of the track and carrier at the top, and minus clearance above the finished flooring as

follows : 12-inches.c. Mesh Top: Fabricate with open mesh fabric at the top of the curtain and hem. Top hem of mesh not less than 1 inch and not more than 1.5 inches

wide, triple thickness, reinforced with integral web, and double lockstitched. Double lockstitch bottom of mesh directly to .5 inch triple thickness,top hem of curtain fabric.

d. Top Hem: Not less than 1 inch and not more than 1.5 inches wide, triple thickness, reinforced with integral web, and double lockstitched.e. Bottom Hem: Not less than 1 inch and not more than 1.5 inches wide, triple thickness, reinforced, and double lockstitched.f. Side Hems: Not less than .5 inch and not more than 1.25 inches wide, with triple turned edges, and single lockstitched.g. Vertical Seams: Not less than .5 inch wide, double turned and double stitched.

D. Fasteners:1. Exposed and concealed fasteners, screws and bolts; use stainless steel.2. Metal Clips: Anchor curtain tracks to exposed grid of lay-in acoustical tile ceilings, with concealed metal (butterfly) type or two piece snap locking type

ceiling clip of high strength spring steel. When it is not possible to install the metal ceiling clip, the cubicle curtain track may be screwed to the ceilinggrid.

E. Fabrication: Weld and grind smooth joints of fabricated components. Form tracks and bends of lengths that will produce the minimum number of joints.Make track sections up to 16 feet without joints. Form corner bend on a 12 inch radius. Provide steel anchor plates, supports and anchors for securingcomponents to building construction. Form flat surface without distortion. Shop assemble components and package complete with anchors and fittings.

F. Installation: Track shall be installed neat, rigid, plumb, level and true, and securely anchored to the overhead construction. Carrier units shall operate smoothly and easily over the full range of travel. Remove damages or defective components and replace with new. Hang curtains on each track.

1


1 ADDENDUM 1 10-23-15

5

21

1

2

4

3

0 10'

1/16" = 1'-0" GRAPHIC SCALE

20' 40' 60'

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS

10/23

/2015

1:10

:29 P

M

GI102

FIRE RATEDPENETRATIONS

CME

EHB

CONCRETEFLOORS WITH AMIN. THICKNESSLESS THAN OREQUAL TO 5"

TYPE OF PENETRANT

FLOOR PENETRATION SYSTEM(FIRST ALPHA COMPONENT= C or F)

CONSTRUCTION

WALL PENETRATION SYSTEM(FIRST ALPHA COMPONENT = C or W

CONCRETEFLOORS WITH AMIN. THICKNESSGREATER THAN

5"

CONCRETE OR MASONRY WALLS FRAMED GYPSUM WALLS FRAMED GYPSUM SHAFT WALLS

1 HOUR MIN. 2 HOUR MIN. 1 HOUR 2 HOUR 3 HOUR 4 HOUR 1 HOUR 2 HOUR 3 HOUR 4 HOUR 1 HOUR 2 HOUR 3 HOUR 4 HOUR

NO PENETRATINGITEMS

METALLIC PIPE,CONDUIT ORTUBING

NON METALLICPIPE, CONDUIT ORTUBING

ELECTRICAL CABLES

CABLE TRAYS WITHELECTRICAL CABLES

INSULATED PIPES

MISCELLANEOUSELECTRICALPENETRANTS

MISCELLANEOUSMECHANICALPENETRANTS

GROUPING OFPENETRANTS

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/AN/AN/AN/A

N/AN/AN/AN/A

N/AN/AN/AN/A

N/AN/A

N/AN/A

N/A

N/A

N/A

F-A-0000-0999OR

C-AJ-0000-0999

F-A-1000-1999OR

C-AJ-1000-1999

F-A-2000-2999OR

C-AJ-2000-2999

F-A-3000-3999OR

C-AJ-3000-3999

F-A-4000-4999OR

C-AJ-4000-4999

F-A-5000-5999OR

C-AJ-5000-5999

F-A-6000-6999OR

C-AJ-6000-6999

F-A-7000-7999OR

C-AJ-7000-7999

F-A-8000-8999OR

C-AJ-8000-8999

C-BJ-0000-0999OR

C-AJ-0000-0999

F-B-1000-1999OR

C-BJ-1000-1999

F-B-2000-2999OR

C-BJ-2000-2999

F-A3000-3999OR

C-BJ-3000-3999

F-A-4000-4999OR

C-AJ-4000-4999

F-A-5000-5999OR

C-AJ-5000-5999

F-A-6000-6999OR

C-AJ-6000-6999

C-AJ-7000-7999OR

C-AJ-7000-7999

F-A-8000-8999OR

C-AJ-8000-8999

W-J-0000-0999OR

C-AJ-0000-0999

W-J-1000-1999OR

C-AJ-1000-1999

W-J-2000-2999OR

C-AJ-2000-2999

W-J-3000-3999OR

C-AJ-3000-3999

W-J-4000-4999OR

C-AJ-4000-4999

W-J-5000-5999OR

C-AJ-5000-5999

W-J-6000-6999OR

C-AJ-6000-6999

W-J-7000-7999OR

C-AJ-7000-7999

W-J-8000-8999OR

C-AJ-8000-8999

W-J-0000-0999OR

C-AJ-0000-0999

W-J-1000-1999OR

C-AJ-1000-1999

W-J-2000-2999OR

C-AJ-2000-2999

W-J-3000-3999OR

C-AJ-3000-3999

W-J-4000-4999OR

C-AJ-4000-4999

W-J-5000-5999OR

C-AJ-5000-5999

W-J-6000-6999OR

C-AJ-6000-6999

W-J-7000-7999OR

C-AJ-7000-7999

W-J-8000-8999OR

C-AJ-8000-8999

C-AJ-0000-0999

W-J-1000-1999OR

C-AJ-1000-1999

W-J-2000-2999OR

C-AJ-2000-2999

W-J-3000-3999OR

C-AJ-3000-3999

W-J-4000-4999

W-J-5000-5999

W-J-6000-6999OR

C-AJ-6000-6999

W-J-8000-8999OR

C-AJ-8000-8999

C-AJ-7000-7999

W-J-1000-1999

W-J-2000-2999

W-J-3000-3999

W-J-4000-4999

W-J-5000-5999

W-J-8000-8999

W-L-1000-1999 W-L-1000-1999 W-L-1000-1999 W-L-1000-1999 W-L-1000-1999 W-L-1000-1999

W-L-0030 W-L-0030

W-L-2000-2999 W-L-2000-2999 W-L-2000-2999 W-L-2000-2999W-L-2000-2999OR

W-L-2000-2999

W-L-2000-2999OR

W-L-2000-2999

W-L-3000-3999OR

W-L-3000-3999

W-L-3000-3999OR

W-L-3000-3999

W-L-4000-4999OR

W-L-4000-4999

W-L-4000-4999OR

W-L-4000-4999

W-L-5000-5999OR

W-L-5000-5999

W-L-5000-5999OR

W-L-5000-5999

W-L-6000-6999OR

W-L-6000-6999

W-L-6000-6999OR

W-L-6000-6999

W-L-7000-7999OR

W-L-7000-7999

W-L-7000-7999OR

W-L-7000-7999

W-L-8000-8999 W-L-8000-8999 W-L-8000-8999 W-L-8000-8999

W-L-3000-3999 W-L-3000-3999 W-L-3000-3999 W-L-3000-3999

W-L-5000-5999 W-L-5000-5999 W-L-5000-5999 W-L-5000-5999

W-L-7000-7999 W-L-7000-7999

THROUGH-PENETRATION FIRESTOP SYSTEM SCHEDULEFIRESTOP SYSTEMS ARE LISTED USING THE ALPHA-ALPHA-NUMERIC IDENTIFICATION SYSTEMPUBLISHED IN UL'S FIRE RESISTANT DIRECTORY, VOL. 2

FOR EACH LOCATION WHERE A FIRE-RESISTANCE-RATED FLOOR OR WALL ASEMBLY IS PENETRATED, PROVIDE A UL-LISTED THROUIGH-PENETRATION FIRESTOP SYSTEM SELECTED FROM THE APPLICABLE UL NUMBER RANGE LISTED ABOVE THAT COMPLIES WITH SECTION --078400 -FIRESTOPPING- AND IS SUITABLE FOR THE PENETRATION CONDITIONS INDICATED FOR THE PROJECT.

SYSTEM DESIGNATIONSTHE FIRST ALPHA COMPONENT IS OPNE OF THREE LETTERSREPRESENTING THE TYPE OF PENETRATION:

LETTER CONSTRUCTION PENETRATED

F FLOOR PENETRATIONS

W WALL PENETRATIONS

C EITHER FLOOR OR WALL PENETRATIONS

THE SECOND ALPHA COMPONENT DESCRIBES THE TYPE OFCONSTRUCTION BEING PENETRATED AND CAN INCLUDE A SINGLELETTER OR DUAL LETTERS:

LETTER DESCRIPTION

A CONCRETE FLOORS WITH A MINIMUM THICKNESS LESS THAN OR EQUAL TO 5 INCHES

B CONCRETE FLOORS WITH A MINIMUM THICKNESS OF MORE THAN 5 INCHES

C FRAMED FLOORS

D STEEL DECKS IN MARINE VESSELS

E FLOOR/CEILING ASSEMBLIES CONSISTING OF CONCRETE WITH MEMBRANE PROTECTION

F THROUGH I WILL NOT BE USED

J CONCRETE OR MASONRY WALLS WITH A MINIMUM THICKNESS LESS THAN OR EQUAL TO 8 INCHES

K CONCRETE OR MASONRY WALLS WITH A MINIMUM THICKNESS OF MORE THAN 8 INCHES

L FRAMED WALLS

M BULKHEADS IN MARINE VESSELS

1/16" = 1'-0"1 THROUGH-PENETRATION FIRESTOP SYSTEM KEY

1 PENETRANT-REFER TO SCHEDULE FOR TYPE2 THROUGH PENETRATION FIRE STOP

SYSTEM-PROVIDE SYSTEM IN ACCORDANCE WITHFIRESTOP SCHEDULE

3 PROVIDE PIPE SLEEVE AT ALL FLOORPENETRATIONS, WHERE AVAILABLE AS ANOPTION IN THE TESTED ASSEMBLY

4 FIRE RESISTANT RATED FLOOR CONSTRUCTION5 EXISTING FIRE RESISTANT RATED WALL

CONSTRUCTION

A REFER TO SHEETS GI001 FOR GENERALABBREVIATIONS AND ARCHITECTURAL SYMBOLS.

1


1 DOE COMMENTS PENDING 09-30-15

PP

P

P

123

101

101A

102

103104

105

106

108

109

109A

110 110A

110B

114

116

117

118

119

120

121

122

109B

124

125A

126

127129

152A

131

130128

134

133

132

532 SFCLASSROOM

135

87 SFCOMM ROOM

136

137

138

609 SFCLASSROOM

139A

628 SFCLASSROOM

139B

140141

143

142

144

913 SFCLASSROOM

146

151E

151D

151C

151B

151

151A

151F

102A

103A104A

111CLASSROOM

938 SF

149NURSING LAB

541 SF

150NURSING LAB

531 SF

148STORAGE

171 SF

TRAVEL PATH: 31'-6"

FECFEC

FEC

FEC

FEC

FEFE

FE

FE

FE

FE

FE

TRAVEL PATH: 47'-6"

TRAV

EL P

ATH

: 46'

-0"

TRAV

EL P

ATH

: 32'

-0"

TRAVEL PATH: 40'-0"

11

3

2

1 1

FE

FEC

FEC 4

5

5

1

1

1

6

1

5 1

5 1 51

20 46 50 11 50 11

125 2

1

20 31

20 32

20 27

300 1

1

1

1

1

1

1 11

1

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:08

:46 P

M

B1-GC111

BUILDING 1 LIFESAFETY PLAN

CME

EHB

LIFE SAFETY LEGEND1 HOUR RATED WALL WITH 20 MIN.RATED DOOR ASSEMBLY.

2 HOUR RATED WALL WITH ONEAND A HALF HOUR RATED DOORFRAME ASSEMBLY.

FEC FIRE EXTINGUISHER CABINET

EEP EMERGENCY EXIT PANEL

EXIT LIGHTS

EW EXIT WIDTH

1/8" = 1'-0"1 BUILDING 1 LIFE SAFETY PLAN

VOICE EVACUATION SPEAKER /STROBE UNIT

FE WALL MOUNTED FIRE EXTINGUISHER

P MANUAL PULL STATION

1 1 HOUR RATED WALL AND CEILINGS2 1 HOUR RATED WALLS, CEILINGS AND FLOOR3 STEEL FRAME WINDOWS WITH WIRE GLASS4 PROVIDE LABEL STATING " EMERGENCY RESCUE- KEEP

AREA CLEAR"5 PROVIDE NEW EVACUATION ROUTE MAP, MATCH EXISTING6 EXISTING POSTED EVACUATION ROUTE MAP TO REMAIN

1 WALL TYPES AND RATINGS ARE BASED ON EXISTING AS- BUILT REVISION DRAWINGS FROM VOA ( VICKERY, OVRESAT AND AWSUMB ASSOCIATES, INC.) DATED 01/16/89.2. EXISTING ROOM IDENTIFICATION SIGNS TO REMAIN.

P

P

P

P

P

P

1

XXXXXX XX

ROOM NET SQUARE FOOTAGE

OCCUPANT LOAD FACTOR

OCCUPANT

1

1

2

2


1 DOE COMMENTS PENDING 09-30-152 ADDENDUM 1 10-23-15

P

P

868 SFCOMPUTER LAB

101

1025 SFCOMPUTER LAB

102

178 SFTUTORING CENTER

116

178 SFOFFICE

115

207 SFOFFICE

114

117

ELECTRICAL118

120

110 111 112 98 SFOFFICE

113

139

140

141

145

142

143

144

146A

147A

148A

100

150

134

137

153 149

149AW

M

152

108

130A

130131132

126127128129

106 105

125 124

119

151

136

133

2126 SFMULTI-PURPOSE ROOM

109B

107

104COMPUTER LAB

2432 SF

109C

109A

FEC

FEC

FEC

FEC

FEC

FEC

FEC

FEC

EEP EEP EEPEEP

EEP EEP EEP

EEP

TRAV

EL P

ATH:

63'-

0"

TRAV

EL P

ATH

: 54'

-6"

TRAV

EL P

ATH

: 63'

-0"

TRAV

EL P

ATH

: 22'

-0"

TRAV

EL P

ATH:

24'-

6"

TRAVEL PATH: 14'-0"

TRAVEL PATH: 56'-6"

FEC

1 1

1 1 1 1 1 1 1 1

21

21

1

21

2 1

31

31

41

51

1

50 18 50 21 50 49

110 1

110 2

* 5

6

110 2

7TRAVEL PATH: 47'-6"

TRAVEL PATH: 22'-0"

TRAVEL PATH: 3

1'-6"

1 1 1

1

1

1

1

1

1

120 106

4

1

4

1

FEC2

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:09

:55 P

M

B2-GC111

BUILDING 2 LIFESAFETY PLAN

CME

EHB

1/8" = 1'-0"1 BUILDING 2 LIFE SAFETY PLAN

LIFE SAFETY LEGEND1 HOUR RATED WALL WITH 20 MIN.RATED DOOR FRAME ASSEMBLY

2 HOUR RATED WALL WITH ONEAND A HALF HOUR RATED DOORFRAME ASSEMBLY

FEC FIRE EXTINGUISHER CABINET

EEP EMERGENCY EXIT PANEL

EXIT LIGHTS

EW EXIT WIDTH

VOICE EVACUATION SPEAKER /STROBE UNIT

FE WALL MOUNTED FIRE EXTINGUISHER

P MANUAL PULL STATION

1 WALL TYPES AND RATINGS ARE BASED ON EXISTING AS- BUILT REVISION DRAWINGS FROM VOA ( VICKERY, OVRESAT AND AWSUMB ASSOCIATES, INC.) DATED 01/16/89.2. EXISTING ROOM IDENTIFICATION SIGNS TO REMAIN.

1 PROVIDE LABEL STATING "EMERGENCY RESCUE - KEEPAREA CLEAR"

2 EXISTING POSTED EVACUATION ROUTE MAP TO REMAIN3 EXISTING FOLDING PARTITION TO REMAIN4 PROVIDE A 6"x6" OCCUPANT LOAD SIGN. MATERIAL TO BE

ACRYLIC PANEL WITH ROUTED MESSAGE. PANEL COLORAND MESSAGE TO BE REVIEWED AND APPROVED BYOWNER PRIOR TO FABRICATION.

5 PROVIDE NEW EVACUATION ROUTE MAP, MATCH EXISTING6 OCCUPANT LOAD CALCULATED PER SREF AS COUNSELING

AREA (5.01.0) 100 NSF FOR FIRST PERSON PLUS 20 NSF FOREACH ADDITIONAL PERSON.

7 NEW FIRE EXSTINGUISHER CABINET, MATCH EXISTING

1

XXXXXX XX

ROOM NET SQUARE FOOTAGE

OCCUPANT LOAD FACTOR

OCCUPANT

1

1

2

2



763 SFCLASSROOM

111147 SF

STORAGE112

22 SFVEST.112A

482 SFCLASSROOM

149

482 SFCLASSROOM

150

281 SFOFFICE

148

123532 SF

CLASSROOM135

87 SFCOMMS

136

138

137

628 SFCLASSROOM

139B

609 SFCLASSROOM

139A

114

116

117

118

119

120

121

122

151B

126

127

128

129

152A

130

131

132

133

134

151D

142

140

141

143

144

146

151 151E

101

101A

102

104A

104

103103A

151F

105

106

108

109

109A 109B

110 110A

110B

151A

151C

124

125A

102A

1 21 2

1 2 1 2

1 2

1 2

1 21 2

1 2

1 2

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT

0 5'


10' 20' 30'

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:07

:46 P

M

B1-AE101

BUILDING 1COMPOSITEFLOOR PLANEXISTING

CME

EHB

1/8" = 1'-0"1 BUILDING 1 COMPOSITE FLOOR PLAN-EXISTING

A. COMPOSITE FLOOR PLAN, SHOWING EXISTING LAYOUT AND AREAS FOR RENOVATION.

1 SEE SHEET B1-AD401 FOR ENLARGEDDEMOLITION PLAN

2 SEE SHEETS B1-AE401 AND B1-AE402 FORENLARGED RENOVATION PLANS

N

1


1 ADDENDUM 1 10-23-15

1 2

23

4

4

4

3

6

7 89

8 9

1 28 9

19 SFVEST.112A

758 SFCLASSROOM

111

12 13

1312

12 13

143 SFSTORAGE

112

1

1 2 1 2

62

4

3

3

4

5

8 9

4

8 9

8 9

476 SFCLASSROOM

149

476 SFCLASSROOM

150

OFFICE148

12 13 12 13

12 13

275 SF13

B1-AE2014

1

532 SFCLASSROOM

135

87 SFCOMM ROOM

136

609 SFCLASSROOM

139A

628 SFCLASSROOM

139B

137

138

2

1 2

2

4

6

6

8 9

8

8 9

8 9

10

1112 13

12 13

12 13

12 13

4

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT


15'10'5'1'0

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:07

:36 P

M

B1-AD401

BUILDING 1ENLARGEDDEMOLITION PLAN

CME

EHB

1/4" = 1'-0"1 ENLARGED DEMOLITION PLAN - ROOMS 111, 112, 112A 1/4" = 1'-0"2 ENLARGED DEMOLITION PLAN - ROOMS 148, 149 , 150

1/4" = 1'-0"3 ENLARGED DEMOLITION PLAN - ROOMS 135, 136, 139A, 139B

1 REMOVE EXISTING VINYL COMPOSITION TILE FLOORINGAND WALL BASE.

2 DEMO POWER/DATA OUTLETS THAT ARE ABOVE 48" AFFAND PATCH WALLS. COORDINATE WITH ELECTRICALDRAWINGS

3 REMOVE WALL4 REMOVE DOOR, FRAME AND HARDWARE TYPICAL.5 REMOVE WINDOW AND PATCH WALL TO MATCH EXISTING.6 REMOVE EXISTING CARPET AND WALL BASE7 REMOVE RAISED FLOOR. PATCH AND REPAIR FLOOR TO

RECEIVE NEW FINISHES.8 REMOVE EXISTING ACOUSTICAL CEILING TILE AND GRID.9 REMOVE EXISTING LIGHT FIXTURES. CONTRACTOR IS

RESPONSIBLE FOR PROPER DISPOSAL.10 EXISTING DATA RACK AND EQUIPMENT TO BE REMOVED BY

OWNER11 EXISTING LADDER TO BE REMOVED12 ANY LIGHT FIXTURES THAT ARE T8 OR NEWER TO BE SAVED

AND RETURNED TO OWNER.13 PREP ALL WALL SURFACES FOR PAINT

A REFER TO SHEET GI100 FOR GENERAL ABBREVIATIONS SYMBOLS.B ITEMS FOR RE-USE TO BE CAREFULLY REMOVED AND STORED AS DIRECTED BY OWNER.C CONTRACTOR TO PROTECT ALL EXISTING BUILDING AREAS AND FINISHES FROM DAMAGE.D EXISTING DOORS AND WINDOWS TO REMAIN, UNLESS OTHERWISE NOTED.E COORDINATE DEMOLITION PLAN WITH NEW RENOVATION PLAN.F REFER TO MECHANICAL AND ELECTRICAL DRAWINGS FOR ADDITIONAL DEMOLITION INFORMATION.G PATCH AND REPAIR WALLS WHICH ARE TO REMAIN WHEN ADJACENT PERPENDICULAR WALLS ARE REMOVED.H REMOVE ALL EXISTING WALL MOUNTED ITEMS, PREP WALL, PAINT AND RE-INSTALL WALL MOUNTED ITEMS. DO NOT PAINT AROUND WALL MOUNTED DEVICES OR EQUIPMENT.I REMOVE POWER TO WALL CLOCKS. PATCH AND REPAIR. OWNER TO PROVIDE AND INSTALL BATTERY OPERATED CLOCKS TO REPLACE EXISTING.J. PATCH AND REPAIR SUBFLOOR WHERE FLOOR OUTLETS ARE REMOVED. PREP FLOOR TO RECIEVE NEW FLOOR FINISH.

N

1

1


1 ADDENDUM 1 10-23-15

1

1

12B1-AE201

4'-0"

20

19

16

12

17

3"

14

131413

13

18

15

3"

AVAV

AV

TS

1'-6"

L

8"

21

4'-0"

2'-0"

29

U U1'-0"

19

23

3"

24

11"

22

22

CENTER

LOCATE ON LEFTSIDE OF CENTERDIVIDER PANEL

CENTERDIVIDERPANEL

14

4"2'-

0"3/

4"

3'-5

1/4"

2'-1"

EXISTING EXTERIOR WALL SYSTEM

EXISTING INTERIOR WALLFURRING

26

25

27

J- BEAD

BACKER ROD AND SEALANT

2

FINISH LIST OF MATERIALSFLOOR:CARPET - PATCRAFT - PATTERN AND COLOR: TO BE SELECTEDBY THE OWNER. SIZE: 24"X24"VCT: ARMSTRONG - PATTERN AND COLOR: TO BE SELECTED BYTHE OWNER. SIZE: 12X12

BASE:RUBBER - JOHNSONITE - COLOR: TO BE SELECTED BY THEOWNER.

WALLS:GENERAL PAINT - SHERWIN WILLIAMS - EGGSHELL FINISH -COLOR: TO BE SELECTED BY THE OWNER.ACCENT PAINT - SHERWIN WILLIAMS - EGGSHELL FINISH -COLOR: TO BE SELECTED BY THE OWNER.

CEILING:ACOUSTICAL CEILING TILE - ROCKFON TROPIC - MODEL: 1000 -EDGE: SQUARE LAY-IN - SIZE: 24" X 24" X 5/8"PAINTED GYPSUM BOARD - SHERWIN WILLIAMS - EGGSHELLFINISH - COLOR: WHITEPAINTED GYPSUM BOARD - ACCENT PAINT - SAME AS WALLACCENT PAINT NOTED ABOVE

MILLWORK:PLASTIC LAMINATE - WILSONART - COLOR: LOWELL ASH 7994-38- VERIFY WITH OWNER

DOORS:EXISTING TO REMAIN.DOOR FRAME: PAINT - SHERWIN WILLIAMS - EGGSHELL FINISH -COLOR: TO BE SELECTED BY THE OWNER.

CUBICLE CURTAIN:ARC COM MED-ARC CUBICLE, PATTERN CANYON-X. COLOR TOBE SELECTED BY THE OWNER.

B-F3050AB-F3050BB-F3050A1 1 1

4 5

2

28

EQUAL

21'-0" CLEAR

6B1-AE20111

EQUAL

SEE ELEVATION 11 FORSPACING TO TOUCH SCREEN

1 1 1

4

2

5

6B1-AE20111

28

B-F3050AB-F3050BB-F3050A

21'-0" CLEAR

EQUALEQUAL


B-F3050A B-F3050B B-F3050A1 1 1

2

4 5

0028

EQUAL

21'-0" CLEAR

6B1-AE201

11


EQUAL

7 7

A-A1106A A-A1106

28

4'-8"

4'-1"

31 TYP

5'-0"

5'-0" 9'-1" 9'-0"

A-A1106A-A1106A A-A1106A-A1106A A-A1106A-A1106A

28

31 TYP.

A-A1106A-A1106AA-A1106A-A1106AA-A1106A-A1106A

5'-0"

9'-0" 9'-1" 4'-1"

28

31 TYP.A-A1106A-A1106A

4'-8"

5'-0"

31 TYP. 9

10 11B-A5080

B-A5075

4'-0"

.

4'-0"

.

1

3

28

B1-AE20111

6

EXISTING STUCCO AND METAL LATH

SAW CUT EXISTING STUCCO ANDPROTECT EXISTING VAPORBARRIER TO ALLOW 6" OFOVERLAP

CONTROL JOINT

STUCCO TO OVER METAL LATH ONCMU

OVERLAP MEMBRANE PER MANUFACTURER

SELF ADHERED VAPOR ANDMOISTURE BARRIER

CMU 8"

32

6"

30

B1-AE20114

B1-AE20115

NEW STUCCO AND METAL LATH

SELF ADHERED VAPOR ANDMOISTURE BARRIER

CMU 8"

METAL FLASHING

CONCRETE SLAB

32

WEEP SCREED

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:08

:01 P

M

B1-AE201

BUILDING 1SECTIONS,ELEVATIONS ANDDETAILS

CME

EHB


15'10'5'1'0

30"20"10"2"0

1½" = 1'-0" GRAPHIC SCALE

15"10"5"1"

3" = 1'-0" GRAPHIC SCALE

0

1 1/2" = 1'-0"11 MILLWORK ELEVATION - ROOMS 111, 135, 139A AND 139B 1 1/2" = 1'-0"12 MILLWORK SECTION

3" = 1'-0"10 EXPOSURE OF EXISTING WINDOWS DETAIL ROOM 111

A REFER TO SHEETS GI100 FOR GENERAL ABBREVIATIONSAND SYMBOLS.

B CONTRACTOR TO PROTECT ALL EXISTING BUILDING AREASAND FINISHES FROM DAMAGE.

C USE OWNER PROVIDED TEMPLATE FOR PROJECTORINSTALLATION COORDINATION. COORDINATE WITH WALLBACKING.

D FURNITURE AND EQUIPMENT PROVIDED BY OWNER.E REMOVE ALL EXISTING WALL MOUNTED ITEMS, PREP WALL,

PAINT AND RE-INSTALL WALL MOUNTED ITEMS. DO NOTPAINT AROUND WALL MOUNTED DEVICES OR EQUIPMENT.

1/4" = 1'-0"3 ELEVATION - ROOM 139A WEST 1/4" = 1'-0"1 ELEVATION - ROOM 111 WEST

1/4" = 1'-0"2 ELEVATION - ROOM 135 SOUTH

1/4" = 1'-0"5 ELEVATION - ROOM 149 SOUTH 1/4" = 1'-0"6 ELEVATION - ROOM 149 NORTH

1/4" = 1'-0"7 ELEVATION - ROOM 150 SOUTH 1/4" = 1'-0"8 ELEVATION - ROOM 150 WEST

1/4" = 1'-0"9 ELEVATION - ROOM 148 WEST

1 WALL MOUNTED WHITEBOARD PROVIDED BY OWNER.CONTRACTOR SHALL COORDINATE AS DIRECTED BYOWNER. TOP AT 7'-0" AFF, UNLESS OTHERWISE NOTED BYOWNER.

2 LOCATE / RELOCATE ANY WALL MOUNTED DEVICESMINIMUM 6" AWAY FROM WHITEBOARDS.

3 RELOCATE EXISITNG TEACHING WALL EQUIPMENT TO WESTWALL. RE-DIRECT CEILING PROJECTOR TO TEACHING WALL.

4 WALL MOUNTED PROJECTOR PROVIDED BY OWNER.CONTRACTOR SHALL COORDINTAE AS DIRECTED BYOWNER. LOCATE POWER/DATA OUTLETS AS DICTATED BYOWNER'S MOUNTING BRACKET DETAILS AND TEMPLATES.

5 PROVIDE 16 INCH HIGH PLYWOOD BACKING BEHINDDRYWALL TO SPAN TWO STUDS. ALIGN WITH OWNER'STEMPLATE. PATCH AND PAINT WALL.

6 MILLWORK CABINET TO HOUSE EQUIPMENT PROVIDED BYTHE OWNER. PROVIDE POWER/DATA OUTLETS ASREQUIRED, SEE ELEVATION 11 / B1-AE201

7 FIELD VERIFY WINDOW LOCATION AND WIDTH. NOTIFYOWNER OF ANY DISCREPANCIES.

8 NOT USED9 WALL MOUNTED SINK.10 WALL MOUNTED DISPOSABLE SOAP DISPENSER11 WALL MOUNTED PAPER TOWEL DISPENSER12 VOICE/DATA OUTLET FOR PHONE.13 A/V BACK BOX WITH GROMMETED OPENING IN COVER

PLATE FOR A/V CABLING ACCESS.14 DUPLEX POWER OUTLET.15 TOUCHSCREEN PROVIDED BY OWNER; DOUBLE GANG BOX

WITH 1/2" CONDUIT.16 QUAD POWER OUTLET.17 VOICE/DATA ONLY OUTLET.18 CONDUIT CONNECTING AV BACK BOXES TOGETHER

CONCEALED WITHIN WALL. SEE ELECTRICAL DRAWINGSFOR REQUIREMENTS.

19 PROVIDE OPEN TOP SHELF ABOVE CABINET WHERE WALLMOUNTED PC AND MONITOR WILL SIT ON TOP OF.

20 DOUBLE DOORS ON FRONT FOR ACCESS TO AV EQUIPMENTTHAT CONNECTS TO THE PROJECTOR. VENT FRONT PANELWITH PERFORATED METAL PANEL. VERIFY PERFORATIONPATTERN WITH OWNER.

21 LOCK HARDWARE PROVIDED BY OWNER.22 PROVIDE 2 " HOLE AND GROMMET AS DIRECTED BY OWNER.23 CABINET TO BE 3/4" PLYWOOD WITH ALL EXTERIOR

EXPOSED SURFACES COVERED WITH PLASTIC LAMINATE.BACK OF CABINET TO BE 1/4" PLYWOOD.

24 OPEN TO WALL.25 REMOVE GYPSUM BOARD, STUDS, FURRING AND RUNNER

TO EXPOSE EXISTING WINDOW26 NEW WINDOW SILL TO MATCH EXISTING27 REMOVE SPANDREL GLASS AND REPLACE WITH VISION

GLASS TO MATCH EXISTING28 RUBBER WALL BASE. TYP. IN ALL ROOMS. REPLACE TO

MATCH EXISTING WALL BASE HEIGHT. REFER TOSPECIFICATIONS.

29 OUTLET O-RING DATA LOCATIONS ARE TO BE EXACTUNLESS APPROVED BY OWNER

30 REMOVE DOOR AND PATCH WALL TO MATCH EXISTINGSTUCCO EXTERIOR

31 AT SIMULATED GAS OUTLETS, PROVIDE 16" HIGH PLYWOODBACKING BEHIND DRYWALL TO SPAN TWO STUDS. PATCHAND PAINT WALL.

32 COORDINATE DETAIL WITH EXISTING

1/4" = 1'-0"4 ELEVATION - ROOM 139B WEST

6" = 1'-0"14 STUCCO PATCH DETAIL ROOM 148

6"4"2"1"


0 8"

1" = 1'-0"13 DEMO DOOR DETAIL ROOM 148

1'0


2' 3' 4'6"

6" = 1'-0"15 STUCCO PATCH DETAIL ROOM 148

2

2

2

2

2



12

C-F0210A

C-F0780A

B-F3050A B-F3050B B-F3050A

B1-AE201

1

3

15 515 15

810B1-AE201

111CLASSROOM

918 SF

532 SFCLASSROOM

135

87 SFCOMM ROOM

136

609 SFCLASSROOM

139A

628 SFCLASSROOM

139B

137

138

B1-AE2012

B1-AE201

3

B-F3

050C

15

B-F3

050A

B-F3

050B

B-F3

050A

15

15

5

15 5B-F3050A B-F3050B B-F3050A

15 15

3

ACCENTPAINT

3

3

2

2

2

2

8

8

8

9

12

4

B1-AE201

4

C-F0210AC-F0210A

1

1

1

4

1

A1

A1

A1A1

C-M4255

C-M4255

C-M4255C-M4255

C-M4255

C-M4255

C-M4255

A-A5180A

C-F0400A

C-F0400A

C-F0400A

C-F0400A

C-F0400A

C-F0400A

C-F0400A

C-M7040

C-M7040

C-M7040

C-M7040

C-M7040

C-M7040

C-M7040

C-M4665

C-M4116A

C-M7010A C-M7010A

C-M7010A

C-M7010A C-M7010A

C-M7010A

C-M7010A

A-A5180B

A-A5180B

A-A5180BA-A5180B

A-A5180B

A-A5180B

A-A5180A

A-A5180A

A-A5180A A-A5180A

A-A5180A

A-A5180A

A-A1106A-A1106A A-A1106

A-A1106A

A-A1106A-A1106A

A-A1106A-A1106A

A-A1106AA-A1106

A-A1106A-A1106A

A-A1106AA-A1106

C-M4705

C-F0415 C-F0415 C-F0465

B-A5

075

C-F0

780

C-F0210

C-F0210

C-M4255C-F0400A

C-M7040

C-M7010A

A-A1106A-A1106A

A-A5

180B

A-A5

180A

C-F0210

C-F0210

C-F0

780

C-F0780C-F0210

C-F0210

C-F0210

C-F0210

C-F0780

B-A5

080

3

3

2 2

2

11 11

11

11

11

11

11

11

9

9

9

VERIFY WITHOWNER - WALLTILE OR PAINT

C-F0465

B1-AE201

9

B1-AE2015 6B1-AE2017

8

C-E0

951

16

17

149NURSING LAB

541 SF

150NURSING LAB

531 SF

148STORAGE

171 SF

7 7

7

7

TYP.

TYP.7 TYP.

TYP. TYP.

A-A5180A A-A5180AA-A5180B

4

6 4

4

13

14

1'-0"

BOTTOM OF DECK

TOP OF SLAB 4" VINYL WALL BASE

PLENUM WIRE

CEILING TILE FRAMING "T"

PERIMETER FRAMING ANGLE

METAL STUD

GYPSUM BOARD, REGULAR 5/8"

METAL STUD

GYPSUM BOARD, REGUALR 5/8"

METAL STUD RUNNER TRACK

1

1

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT


15'10'5'1'0

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:08

:22 P

M

B1-AE401

BUILDING 1ENLARGED FLOORPLAN

CME

EHB






1/4" = 1'-0"1 RENOVATION FLOOR PLAN, ROOM 111

1/4" = 1'-0"3 RENOVATION FLOOR PLAN, ROOMS 135, 136, 139A, 139B

1/4" = 1'-0"2 RENOVATION FLOOR PLAN, ROOMS 148, 149, 150

OWNER FURNISHED / OWNER INSTALLED

C-E0951 Cart, MedicalC-F0210 Chair, Side, Without ArmsC-F0210A Chair, ClassroomC-F0400A Cabinet, BedsideC-F0415 Cabinet, Lateral FileC-F0465 Supply CabinetC-F0780 Table, 60x24C-F0780A Table, Kidney ShapeC-M4116A Monitor, Vital SignsC-M4255 Stand, IV, AdjustableC-M4665 Stretcher, Recovery, SurgicalC-M4705 Wheelchair, Patient Transport, FoldingC-M7010A Patient BedC-M7040 Table, Overbed

OWNER FURNISHED / CONTRACTOR ROUGH IN

B-A5075 Dispenser, Soap, DisposableB-A5080 Dispenser, Paper Towel, Wall MountedB-F3050A WhiteboardB-F3050B Whiteboard & ProjectorB-F3050C Graph Board, Existing

CONTRACTOR FURNISHED / CONTRACTOR INSTALLED

A-A1106 Medical Gas Outlet LocationA-A1106A Vacuum SlideA-A5180A Track, Cubicle Curtain, Surface MountedA-A5180B Curtain, Cubicle

FINISH LIST OF MATERIALS

FLOOR:CARPET - PATCRAFT - PATTERN AND COLOR: TO BE SELECTEDBY THE OWNER SIZE: 24"X24"VCT: ARMSTRONG - PATTERN AND COLOR: TO BE SELECTED BYTHE OWNER. SIZE: 12X12

BASE:RUBBER - JOHNSONITE - COLOR: TO BE SELECTED BY THEOWNER.

WALLS:GENERAL PAINT - SHERWIN WILLIAMS - EGGSHELL FINISH -COLOR: TO BE SELECTED BY THE OWNER.ACCENT PAINT - SHERWIN WILLIAMS - EGGSHELL FINISH -COLOR: TO BE SELECTED BY THE OWNER.

CEILING:ACOUSTICAL CEILING TILE - ROCKFON TROPIC - MODEL: 1000 -EDGE: SQUARE LAY-IN - SIZE: 24" X 24" X 5/8"PAINTED GYPSUM BOARD - SHERWIN WILLIAMS - EGGSHELLFINISH - COLOR: WHITEPAINTED GYPSUM BOARD - ACCENT PAINT - SAME AS WALLACCENT PAINT NOTED ABOVE

MILLWORK:PLASTIC LAMINATE - WILSONART - COLOR: LOWELL ASH 7994-38- VERIFY WITH OWNER


CUBICLE CURTAIN:ARC COM MED-ARC CUBICLE, PATTERN CANYON-X. COLOR TOBE SELECTED BY THE OWNER.

1 MILLWORK CABINET TO HOUSE EQUIPMENT PROVIDED BY THEOWNER. PROVIDE POWER/DATA OUTLETS AS REQUIRED, SEEELEVATION 11/B1-AE201

2 PAINT ALL WALLS GENERAL PAINT COLOR, UNLESSOTHERWISE NOTED.

3 ACCENT PAINT WALL4 AREA OF WORK WHERE DOOR WAS REMOVED AND WALL

PATCHED FOR NEW PAINT5 WALL MOUNTED PROJECTOR PROVIDED BY OWNER.

CONTRACTOR SHALL COORDINATE AS DIRECTED BY OWNER.LOCATE POWER/DATA OUTLETS AS DICTATED BY OWNER'SMOUNTING BRACKET DETAILS AND TEMPLATES.

6 AREA OF WORK WHERE WINDOW WAS REMOVED AND WALLPATCHED FOR NEW PAINT

7 AT SIMULATED GAS OUTLETS, PROVIDE 16" HIGH PLYWOODBACKING BEHIND DRYWALL TO SPAN TWO STUDS. PATCH ANDPAINT WALL.

8 NEW CARPET AND WALL BASE9 NEW VCT AND WALL BASE10 NOT USED11 REFER TO GI101 FOR CUBICLE CURTAIN TRACK AND CURTAIN

SPECIFICATION12 RELOCATE EXISTING GRAPH BOARD AS DIRECTED BY THE

OWNER. FINAL LOCATION TBD.13 NEW ACT CEILING AT 9'-0" AFF14 GYPSUM BOARD TO EXTEND 6" ABOVE CEILING.15 WALL MOUNTED WHITEBOARD PROVIDED BY OWNER.

CONTRACTOR SHALL COORDINATE AS DIRECTED BY OWNER.TOP AT 7'-0" AFF, UNLESS OTHERWISE NOTED BY OWNER.

16 BASE BID SINK W/O PLUMBING. SEE PLUMBING DRAWINGSADD ALTERNATE 2 FOR WORKING SINK

17 WALL TO BE PAINTED TO MATCH EXISTING

N

3" = 1'-0"4 WALL ASSEMBLY TYPE A1

15"10"5"1"


0

1

1


1 ADDENDUM 1 10-23-15

1

9'-0" AFF

12'-0" AFF111CLASSROOM

938 SF4

B1-AE410

1

1

12'-0" AFF

148STORAGE

171 SF

149NURSING LAB

541 SF

150NURSING LAB

531 SF

4

4B1-AE410

13B1-AE201

TYP. 4

1

1

9'-0" AFF

1

532 SFCLASSROOM

135

609 SFCLASSROOM

139A87 SF

COMM ROOM136

628 SFCLASSROOM

139B137

138

12'-0" AFF

9'-0" AFF

8'-0" AFF

9'-0" AFF

9'-0" AFF

2

3

4B1-AE410

1

6"1"

SEE RCPFOR HEIGHT

SEE RCPFOR HEIGHT

6"

ACOUSTICAL CEILING TILE

ACOUSTICAL CEILING TILE

CORNERBEAD

METAL STUD RUNNER TRACK

GYPSUM BOARD, REGULAR 5/8"HANGER WIRE


AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT


15'10'5'1'0

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:08

:36 P

M

B1-AE410

BUILDING 1REFLECTEDCEILING PLAN

CME

EHB

1/4" = 1'-0"1 REFLECTED CEILING PLAN ROOM 111 1/4" = 1'-0"2 REFLECTED CEILING PLAN - ROOMS 148, 149, 150

1/4" = 1'-0"3 REFLECTED CEILING PLAN - ROOMS 135, 136, 139A, 139B

1 EXISTING CEILING SLOPES UPWARDS TOWARDSCLERESTORY WINDOWS. NEW DETAIL SHOWSDRYWALL BULKHEAD TRANSITION

2 REMOVE HATCH DOOR PANEL. DEMOLISH SHAFTAND EXTEND EXITING CEILING GRID TO MATCH 8'-0"DROP CEILING.

3 COORDINATE ACOUSTICAL CEILING TILE WITHCOMMUNICATION RACK LOCATION AND HEIGHT.

4 CUBICLE CURTAIN TRACKS

A REFER TO SHEETS GI100 FOR GENERALABBREVIATIONS AND SYMBOLS.

B CONTRACTOR TO PROTECT ALL EXISTINGBUILDING AREAS AND FINISHES FROM DAMAGE.

C USE OWNER PROVIDED TEMPLATE FORPROJECTOR INSTALLATION COORDINATION.COORDINATE WITH WALL BACKING.

D FURNITURE AND EQUIPMENT PROVIDED BYOWNER.

E REMOVE ALL EXISTING WALL MOUNTED ITEMS,PREP WALL, PAINT AND RE-INSTALL WALLMOUNTED ITEMS. DO NOT PAINT AROUND WALLMOUNTED DEVICES OR EQUIPMENT.

N

3" = 1'-0"4 CEILING DETAIL


1 ADDENDUM 1 10-23-15

1

868 SFCOMPUTER LAB

101

1025 SFCOMPUTER LAB

102


116

178 SFOFFICE

115

207 SFOFFICE

114

117

ELECTRICAL118

120

110 111 OFFICE 98 SFOFFICE

113

139

140

141

145

142

143

144

146A

147A

148A

100

150

134

137

153 149

149AW

M

152

108

130A

130131132

126127128129

106 105

125 124

119

151

136

133


109B

107

1 2 1 2 1 2

1 2

1 2

1 2

1 2

1 2

3

3

103COMPUTER LAB

2432 SF

109C

109AAR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT

0 5'


10' 20' 30'

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:09

:08 P

M

B2-AE101

BUILDING 2COMPOSITEFLOOR PLANEXISTING

CME

EHB

1/8" = 1'-0"1 BUILDING 2 COMPOSITE FLOOR PLAN-EXISTING

A COMPOSITE FLOOR PLAN SHOWING EXISTING LAYOUT AND AREAS FOR RENOVATION.

1 SEE SHEET B2-AD401 FOR ENLARGED DEMOLITIONPLAN.

2 SEE SHEETS B2-AE401 AND FOR ENLARGEDRENOVATION PLANS.

3 EXISTING OPERABLE PARTITION TO REMAIN.

N

1

1


1 ADDENDUM 1 10-23-15

868 SFCOMPUTER LAB

101

1025 SFCOMPUTER LAB

102

110 111 112

1

1

2 2

1

1

5 6 5 6

8 8 2 / B

2-AD

401

9 10 9 10

2432 SFCOMPUTER LAB

103

1

1

1

2


116

178 SFOFFICE

115

207 SFOFFICE

114

98 SFOFFICE

113

2 5 6

5 6

2 5 6

2 5 6

2 5 6

4

8 81 / B

2-AD

401

9 10

9 10

9 10

9 10

9 10


109B

1

1

1

1

2

3

3

7

7

1

1

7

1

109C

109A

9 10

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT


15'10'5'1'0

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:08

:57 P

M

B2-AD401

BUILDING 2ENLARGEDDEMOLITION PLAN

CME

EHB

1/4" = 1'-0"1 ENLARGED DEMOLITION PLAN - ROOMS 101, 102

1 ADD ALTERNATE 3, TO RE-UPHOLSTER EXISTING ACOUSTICALWALL FABRIC PANELS AND EXISTING OPERABLE WALLPARTITION. EXISTING FRAMES AND PANELS TO REMAIN. NEWFABRIC ONLY. VERIFY LOCATIONS, PANEL WIDTH AND HEIGHTS.

2 REMOVE EXISTING CARPET AND WALL BASE3 EXISTING OPERABLE WALL PARTITION4 REMOVE 1" X 6" WOOD STUD AND REPLACE WITH FLUSH

DRYWALL HEADER.5 EXISTING GRID TO REMAIN, REPLACE EXISTING ACOUSTICAL

TILE.6 REMOVE EXISTING LIGHT FIXTURES. CONTRACTOR IS

RESPONSIBLE FOR PROPER DISPOSAL.7 REMOVE CEILING MOUNTED PROJECTION SCREEN8 EXISTING EMREGENCY EGRESS WINDOWS TO REMAIN9 ANY LIGHT FIXTURES THAT ARE T8 OR NEWER TO BE SAVED

AND RETURNED TO OWNER.10 PREP ALL WALL SURFACES FOR PAINT

1/4" = 1'-0"2 ENLARGED DEMOLITION PLAN - ROOM 104 1/4" = 1'-0"3 ENLARGED DEMOLITION PLAN - ROOM 109

N

A REFER TO SHEET GI100 FOR GENERAL ABBREVIATIONS SYMBOLS.B ITEMS FOR RE-USE TO BE CAREFULLY REMOVED AND STORED AS DIRECTED BY OWNER.C CONTRACTOR TO PROTECT ALL EXISTING BUILDING AREAS AND FINISHES FROM DAMAGE.D EXISTING DOORS AND WINDOWS TO REMAIN, UNLESS OTHERWISE NOTED.E COORDINATE DEMOLITION PLAN WITH NEW RENOVATION PLAN.F REFER TO MECHANICAL AND ELECTRICAL DRAWINGS FOR ADDITIONAL DEMOLITION INFORMATION.G PATCH AND REPAIR WALLS WHICH ARE TO REMAIN WHEN ADJACENT PERPENDICULAR WALLS ARE REMOVED.H REMOVE ALL EXISTING WALL MOUNTED ITEMS, PREP WALL, PAINT AND RE-INSTALL WALL MOUNTED ITEMS. DO NOT PAINT AROUND WALL MOUNTED DEVICES OR EQUIPMENT.I REMOVE POWER TO WALL CLOCKS. PATCH AND REPAIR. OWNER TO PROVIDE AND INSTALL BATTERY OPERATED CLOCKS TO REPLACE EXISTING.J. PATCH AND REPAIR SUBFLOOR WHERE FLOOR OUTLETS ARE REMOVED. PREP FLOOR TO RECIEVE NEW FLOOR FINISH.

1


1 ADDENDUM 1 10-23-15

1

1

B-F3050B B-F3050A

B-M1

801F

2 1 1

3 4

14'-8"5'-5"

4'-0"

771

1

1

B-F3050A B-F3050B

B-M1

801F1 1 2

3 4

14'-8" 4'-3"

4'-0"

1

7 1

B1-AE20111

5

6


17 571

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT


15'10'5'1'0

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:09

:19 P

M

B2-AE201

BUILDING 2SECTIONS,ELEVATIONS ANDDETAILS

CME

EHB






1/4" = 1'-0"1 ELEVATION - ROOM 109 WEST 1/4" = 1'-0"2 ELEVATION - ROOM 109 EAST

1 WALL MOUNTED WHITEBOARD PROVIDED BY OWNER.CONTRACTOR SHALL COORDINATE AS DIRECTED BY OWNER.TOP AT 7'-0" AFF, UNLESS OTHERWISE NOTED BY OWNER.

2 LOCATE / RELOCATE ANY WALL MOUNTED DEVICES MINIMUM 6"AWAY FROM WHITEBOARDS.

3 WALL MOUNTED PROJECTOR PROVIDED BY OWNER.CONTRACTOR SHALL COORDINATE AS DIRECTED BY OWNER.LOCATE POWER/DATA OUTLETS AS DICTATED BY OWNER'SMOUNTING BRACKET DETAILS AND TEMPLATES.

4 PROVIDE 16" HIGH PLYWOOD BACKING BEHIND DRYWALL TOSPAN TWO STUDS. ALIGN WITH OWNER'S TEMPLATE. PATCHAND PAINT WALL.

5 PULL POWER / DATA OUTLETS TO FRONT SURFACE OFACOUSTICAL WALL PANEL. BOX / FRAME OUTLET FOR A FLUSHINSTALLATION.

6 MILLWORK CABINET TO HOUSE EQUIPMENT PROVIDED BY THEOWNER. PROVIDE POWER/DATA OUTLETS AS REQUIRED, SEEELEVATION 11 /B1-AE201

7 RUBBER WALL BASE. REPLACE TO MATCH EXISTING WALL BASEHEIGHT. SEE SPECIFICATION


B-F3050A WhiteboardB-F3050B Whiteboard & ProjectorB-M1801F Wall Mounted PC


FLOOR:CARPET - PATCRAFT - PATTERN AND COLOR: TO BE SELECTED BYTHE OWNER. SIZE: 24" X 24"

BASE:RUBBER - JOHNSONITE - COLOR: TO BE SELECTED BY THE OWNER.

WALLS:GENERAL PAINT - SHERWIN WILLIAMS- EGGSHELL FINISH - COLOR:TO BE SELECTED BY THE OWNER.

ACCENT PAINT - SHERWIN WILLIAMS - EGGSHELL FINISH - COLOR: TOBE SELECTED BY THE OWNER.

CEILING:ACOUSTICAL CEILING TILE - ROCKFON TROPIC - MODEL: 1000 -EDGE: SQUARE LAY-IN - SIZE: 24" X 24" X 5/8"

PAINTED GYPSUM BOARD - SHERWIN WILLIAMS - EGGSHELL FINISH -COLOR: WHITE

MILLWORK:PLASTIC LAMINATE - WILSONART - COLOR: LOWELL ASH 7994-38 -VERIFY WITH OWNER


ADD ALTERNATE 3- FABRIC FOR WALL PANELS:GUILFORD OF MAINE -PATTERN: 2314 PHONE TAG; VERIFY WITH OWNER PRIOR TOPURCHASECOLOR: TO BE SELECTED BY THE OWNER.

1/4" = 1'-0"3 ELEVATION - ROOM 101 SOUTH 1/4" = 1'-0"4 ELEVATION - ROOM 102 WEST

1


1 ADDENDUM 1 10-23-15

1

T

T

868 SFCOMPUTER LAB

101

1025 SFCOMPUTER LAB

102

1

2

3

1

2

3

3 3

2 / B

2-AE

401

9 B2-AE2013 B2-AE201

4

10B-M1801F

2432 SFCOMPUTER LAB

103

98 SFOFFICE

113


116

178 SFOFFICE

115

207 SFOFFICE

114

1 2

3

52

5 2

5 2

5 2

1 / B

2-AE

401

1


109B

3

B-F3050BB-F3050A

677

B-F3050BB-F3050A

67

7

21

B-M1801F

B-M1801F48

48

B2-AE201

1

B2-AE201

2

109C

109A

1

11

112

2

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT


15'10'5'1'0

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:09

:29 P

M

B2-AE401

BUILDING 2ENLARGED FLOORPLAN

CME

EHB

1/4" = 1'-0"1 RENOVATION FLOOR PLAN, ROOMS 101, 102

1/4" = 1'-0"2 RENOVATION FLOOR PLAN, ROOMS 104, 114, 115, 116


FLOOR:CARPET - PATCRAFT - PATTERN AND COLOR: TO BE SELECTED BYTHE OWNER. SIZE: 24" X 24"

BASE:RUBBER - JOHNSONITE - COLOR: TO BE SELECTED BY THE OWNER.

WALLS:GENERAL PAINT - SHERWIN WILLIAMS- EGGSHELL FINISH - COLOR:TO BE SELECTED BY THE OWNER.

ACCENT PAINT - SHERWIN WILLIAMS - EGGSHELL FINISH - COLOR:TO BE SELECTED BY THE OWNER.

CEILING:ACOUSTICAL CEILING TILE - ROCKFON TROPIC - MODEL: 1000 -EDGE: SQUARE LAY-IN - SIZE: 24" X 24" X 5/8"

PAINTED GYPSUM BOARD - SHERWIN WILLIAMS - EGGSHELL FINISH- COLOR: WHITE

MILLWORK:PLASTIC LAMINATE - WILSONART - COLOR: LOWELL ASH 7994-38 -VERIFY WITH OWNER


ADD ALTERNATE 3- FABRIC FOR WALL PANELS:GUILFORD OF MAINE -PATTERN: 2314 PHONE TAG; VERIFY WITH OWNER PRIOR TOPURCHASECOLOR: TO BE SELECTED BY THE OWNER.

1 PAINT ALL WALLS GENERAL PAINT COLOR, UNLESS OTHERWISENOTED.

2 NEW CARPET AND WALL BASE3 ADD ALTERNATE 3, REUPHOLSTER ACOUSTICAL WALL PANELS

AND OPERABLE WALL PANELS WITH NEW FABRIC. VERIFYLOCATIONS, PANEL WIDTHS AND HEIGHTS. PROVIDE COST.

4 PROVIDE 16 INCH HIGH PLYWOOD BACKING BEHIND DRYWALLTO SPAN TWO STUDS. ALIGN WITH OWNER'S TEMPLATE. PATCHAND PAINT WALL.

5 PAINT ALL WALLS ACCENT COLOR6 WALL MOUNTED PROJECTOR PROVIDED BY OWNER.

CONTRACTOR SHALL COORDINATE AS DIRECTED BY OWNER.LOCATE POWER/DATA OUTLETS AS DICTATED BY OWNER'SMOUNTING BRACKET DETAILS AND TEMPLATES.

7 WALL MOUNTED WHITEBOARD PROVIDED BY OWNER.CONTRACTOR SHALL COORDINATE AS DIRECTED BY OWNER.TOP AT 7'-0" AFF, UNLESS OTHERWISE NOTED BY OWNER.

8 WALL MOUNTED PC PROVIDED BY OWNER. CONTRACTORSHALL COORDINATE AS DIRECTED BY OWNER. LOCATE POWER/ DATA OUTLETS AS DIRECTED BY OWNER'S MOUNTINGBRACKET DETAILS AND TEMPLATES.

9 MILLWORK CABINET TO HOUSE EQUIPMENT PROVIDED BY THEOWNER. PROVIDE POWER/DATA OUTLETS AS REQUIRED, SEEELEVATION 11 /B1-AE201

10 COORDINATE NEW WALL MOUNTED EQUIPMENT AND POWER /DATA WITH EXISTING TEACHING WALL EQUIPMENT

11 CONTRACTOR TO PROTECT EXISTING CURTAINS FROM DAMAGEAND DEBRIS DURING REMODEL.

N

1/4" = 1'-0"3 RENOVATION FLOOR PLAN, ROOM 109







B-F3050A WhiteboardB-F3050B Whiteboard & ProjectorB-M1801F Wall Mounted PC

2

2

2



868 SFCOMPUTER LAB

101

1025 SFCOMPUTER LAB

102

110 111 112

9'-0" AFF 9'-0" AFF

1 1

2 / B

2-AE

410

2432 SFCOMPUTER LAB

103


116

178 SFOFFICE

115

207 SFOFFICE

114

OFFICE113

9'-0" AFF

9'-0" AFF

9'-0" AFF

9'-0" AFF

1 / B

2-AE

410

3 1

1

1

1

1

9'-0" AFF

4B2-AE410

2

2

2


109B

12'-0" AFF

12'-0" AFF

12'-0" AFF

1

2

2

109A

109C

1

1

1

4

4

2

2

2

2

3

PLENUM WIRE

CEILING TILE FRAMING "T"

PERIMETER FRAMING ANGLE


ACT CEILING TILE

METAL STUD

CORNER BEAD

2

AR0015014

PAT R

I CKA. W H

I T ESTA

TEOF FLOR I DA

REGI S T ERED ARC

H

I TECT


15'10'5'1'0

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

1:09

:44 P

M

B2-AE410

BUILDING 2REFLECTEDCEILING PLAN

CME

EHB

1 INSTALL NEW ACOUSTICAL TILE INEXISTING GRID. FIELD VERIFY EXISTINGGRID LOCATION WITH NEW MECHANICALAND ELECTRICAL DEVICES.

2 EXISTING OPERABLE WALL PARTITION TOREMAIN

3 REPLACE 1" X 6" STUD WITH DRYWALLHEADER FLUSH WITH ACOUSTICALCEILING TILES.

4 EXISTING SOFFIT TO REMAIN.

1/4" = 1'-0"1 BUILDING 2 REFLECTED CEILING PLAN - ROOM 101, 102

1/4" = 1'-0"2 BUILDING 2 REFLECTED CEILING PLAN - ROOM 103, 113, 114, 115, 116 1/4" = 1'-0"3 ENLARGED REFLECTED CEILING PLAN - ROOM 109

A REFER TO SHEETS GI100 FOR GENERALABBREVIATIONS AND SYMBOLS.

B CONTRACTOR TO PROTECT ALL EXISTINGBUILDING AREAS AND FINISHES FROM DAMAGE.

C USE OWNER PROVIDED TEMPLATE FORPROJECTOR INSTALLATION COORDINATION.COORDINATE WITH WALL BACKING.

D FURNITURE AND EQUIPMENT PROVIDED BYOWNER.

E REMOVE ALL EXISTING WALL MOUNTED ITEMS,PREP WALL, PAINT AND RE-INSTALL WALLMOUNTED ITEMS. DO NOT PAINT AROUND WALLMOUNTED DEVICES OR EQUIPMENT.

4"


0 1' 2' 3' 5'4'

N

2

2

3" = 1'-0"4 DRYWALL HEADER DETAIL

15"10"5"1"


0

2



2

0.01

WH1 EQUIPMENT MARK

SCHEDULE REFERENCE

EQUIPMENT TYPE

GENERAL IDENTIFICATION

WATER HAMMER ARRESTER MARK

PLUMBING DRAINAGE INSTITUTEWATER HAMMER ARRESTER SIZE

PDI-A

RISER CONTINUATION MARK

POINT OF CONNECTION BETWEEN NEW ANDEXISTING CONSTRUCTION

POINT OF REMOVAL - DEMOLITION

PIPING

RISE OR DROP

RISER UP (ELBOW)

RISER DOWN (ELBOW)

STRAINER

FLOOR/EXTERIOR CLEANOUT

UNION

HOSE BIBB

CLEANOUT

CHECK VALVE

GLOBE VALVE

GATE VALVE

MANUAL BALANCING VALVE

PLUG VALVE

BALL VALVE

BACKWATER VALVE

BRANCH BOTTOM CONNECTION

BRANCH TOP CONNECTION

CAP

PRESSURE REDUCING VALVE

VALVES

PLUMBING SYMBOLS

FITTINGS

BUTTERFLY VALVE

GLOBE VALVE

VALVE IN RISER

WATER METER

ACTUATING SWITCH

FLOW (IN DIRECTION OF ARROW)

VENT THROUGH ROOF

OR

OR

OR

HOT WATER MIXING VALVE

ROOF DRAIN/AREA DRAIN/DECK DRAIN

FLOOR PENETRATION

FLOOR DRAIN/HUB DRAIN

FLOOR SINK

SPECIALTIES

ROOF DRAIN

HUB DRAIN

SEISMIC BRACING

M

LAB AIR INTAKELAI

OEE ORAL EVACUATION EXHAUST

ABB

GTV

HVAC

HD

HP

HEATING/VENTILATING/AIR CONDITIONING

HUB DRAIN

HORSE POWER

GATE VALVE

DESCRIPTION

HOT WATER

HOT WATER RETURN

HW

HWR

GAL GALLON

G GAS

GV GLOBE VALVE

HB HOSE BIBB

GR GREASE WASTE

SECONDARY RAINWATERSRW

LAB AIRLA

ROOF DRAINRD

SOFT COLD WATERSCW

PLUG VALVEPV

SANITARYSAN

VENTV

SP SUMP PUMP

INVERT

PRESSURE

REQUIRED

ROTATIONS PER MINUTE

REGULATING

REFERENCE

POUNDS PER SQUARE INCH

RAINWATER

PLUMBING DRAINAGE INSTITUTE

VENT THROUGH ROOF

WITH

WATER HAMMER ARRESTER

WATER HEATER

WALL CLEAN OUT

INV

PDI

PSI

RW

VTR

W/

WH

WHA

WCO

RPM

REQD

REG

REF

PRESS.

WC WATER CLOSET

LAV LAVATORY

SH SHOWER

JS JANITOR'S SINK

TEMPERATURETEMP

WHY WALL HYDRANT

WM WATER METER

PWB PLUMBING WALL BOX

RP RECIRCULATION PUMP

SE SEWAGE EJECTOR

INVERT ELEVATIONI.E.

ABB DESCRIPTION

ABBREVIATIONS

POUNDS PER SQUARE INCH GAGEPSIG

TYPICALTYP

OE ORAL EVACUATION

PLASTER TRAPPT

INTERNATIONAL PLUMBING CODEIPC

LAVATORYL

SINKS

SITE DRAINSD

SUPPLY AND DRAIN UNITSDU

URINALUR

YHY YARD HYDRANT

SAFETY RELIEF VALVE

WALL HYDRANT (FREEZEPROOF)

ROOF HYDRANT

PLUMBING GENERAL NOTES:

DENTAL AIR INTAKEDAI

BASEMENTBSMT

ABB

FCO

AFF

BFP

CFM

DWG

ECO

ELEV

CAP

CONT

EA

CO

BV

FLOOR CLEANOUT

EXTERIOR CLEANOUT

ELEVATION

CONTINUATION

DRAWING

EACH

CLEANOUT

BALL VALVE

CUBIC FEET PER MINUTE

CAPACITY

ABOVE FINISHED FLOOR

BACKFLOW PREVENTER

DESCRIPTION

CV CHECK VALVE

BCW BOOSTED COLD WATER

BHW BOOSTED HOT WATER

BALANCING VALVEBLV

FLOOR DRAINFD

AC AIR COMPRESSOR

BWV BACKWATER VALVE

CD CONDENSATE WASTE

DA DENTAL AIR

ESEW EMERGENCY SHOWER / EYEWASH

DOWNDN

AIR PRESSURE REDUCING STATIONAPR

BFG BELOW FINISHED GRADE

DI DEIONIZED WATER

CFH CUBIC FEET PER HOUR

BTUH BRITISH THERMAL UNITS PER HOUR

AD AREA DRAIN

EWC ELECTRIC WATER COOLER

EW EYEWASH

LEVELLVL

MIXING VALVEMX

ZVB MEDICAL GAS ZONE VALVE BOX

MAI

MAXIMUM

MINIMUM

MEDICAL

NITROGEN

NATIONAL PIPE THREAD

NORMALLY OPEN

MIN

NPT

(N.O.)

NI

MED

MAX.

MMP

MG MEDICAL GAS

MEDICAL GAS MASTER ALARM PANEL

MEDICAL AIR INTAKE

CW COLD WATER

MA MEDICAL AIR

ELEC ELECTRIC

FM FORCE MAIN

FFE

FLR

FINISHED FLOOR ELEVATION

FLOOR

FO FUEL OIL

CONN CONNECTION

CA COMPRESSED AIR

CAI COMPRESSED AIR INTAKE

AUTO AUTOMATIC

FW FILTERED WATER

MAP MEDICAL GAS MASTER ALARM PANEL

MEDICAL VACUUMMV

MVE MEDICAL VACUUM EXHAUST

OX OXYGEN

VACUUM PUMP

VACUUM SLIDE

VP

VS

WASTEW

AAP MEDICAL GAS AREA ALARM PANEL

NITROGEN CONTROL CABINET

NORMALLY CLOSED(N.C.)

NCC

NITROUS OXIDENO

WASTE ANESTHETIZING GAS EXHAUSTWAGE

WAG WASTE ANESTHETIZING GAS

TRAP PRIMERTP

SQUARESQ

PRESSURE BOOSTERPB

CO

RO

AW

AW

NI

SRW

AV

NO

MV

MVE

RW

RW

NITROUS OXIDE PIPING

HOT WATER RETURN PIPING

RAINWATER PIPING ABOVE GRADE/SLAB

RAINWATER PIPING BELOW GRADE/SLAB

HOT WATER PIPING

BOOSTED COLD WATER PIPING

VENT PIPING

SANITARY OR WASTE PIPING BELOWGRADE/SLAB

SANITARY OR WASTE PIPING ABOVEGRADE/SLAB

MEDICAL AIR PIPING

FORCE MAIN PIPING BELOW GRADE/SLAB

HOT WATER PIPING (140°F)

SECONDARY RAINWATER PIPING

NITROGEN PIPING

ACID WASTE PIPING ABOVE GRADE/SLAB

ACID WASTE PIPING BELOW GRADE/SLAB

GREASE WASTE PIPING BELOWGRADE/SLAB

ACID VENT PIPING

FORCE MAIN PIPING ABOVE GRADE/SLAB

SOLAR HOT WATER RETURN PIPING

SOLAR HOT WATER PIPING

HOT WATER RETURN PIPING (140°F)

CONDENSATE WASTE PIPING ABOVEGRADE/SLAB

CONDENSATE WASTE PIPING BELOWGRADE/SLAB

SOFT COLD WATER PIPING

COLD WATER PIPING

REVERSE OSMOSIS PIPING

CARBON DIOXIDE PIPING

MEDICAL AIR INTAKE PIPING

MEDICAL VACUUM PIPING

MEDICAL VACUUM EXHAUST PIPING

MA

MAI

140

SHW

SHWR

140

B

S

FM

GR

CD

FM

CD

DW DRINKING WATER PIPING

HOT WATER PIPING (122°F)122

OX OXYGEN PIPING

CA

CAI

COMPRESSED AIR PIPING

COMPRESSED AIR INTAKE PIPING

WAG WASTE ANESTHETIZING GAS PIPING

WAGE WASTE ANESTHETIZING GAS EXHAUST PIPING

FS FLOOR SINK

EXISTING EQUIPMENT/PIPING DESIGNATION(E)

PRESSURE REDUCING VALVEPRV

DA DENTAL AIR PIPING

DSV DENTAL SURGICAL VACUUM

OE ORAL EVACUATION PIPING

LA LABORATORY AIR PIPING

LV LABORATORY VACUUM PIPING

1. REFER TO SPECIFICATIONS FOR ALL PIPING CONSTRUCTION AND INSTALLATIONREQUIREMENTS.

2. REFER TO TYPICAL DETAIL SHEETS FOR ADDITIONAL VALVING, ACCESSORIES,EQUIPMENT CONNECTIONS, AND ASSEMBLY DETAILS.

3. PIPING LOCATIONS SHOWN ARE SCHEMATIC. REFER TO SPECIFICATIONS FOR SHOPDRAWING AND COORDINATION DRAWING REQUIREMENTS. DO NOT PROCEED WITHINSTALLATION OF PIPING UNTIL APPROVED SHOP DRAWINGS ARE AVAILABLE AT THESITE.

4. PROVIDE ACCESS PANELS IN NON-ACCESSIBLE GENERAL CONSTRUCTIONSUBSTRATES FOR MAINTENANCE AND ADJUSTMENT OF ALL CONCEALED VALVES,FLOW CONTROL DEVICES AND EQUIPMENT. REFER TO SPECIFICATIONS. WOOD,GYPSUM DRYWALL AND CONCEALED SPLINE TILE CEILINGS ARE CONSIDEREDNON-ACCESSIBLE.

5. REFER TO SPECIFICATIONS FOR SLEEVING REQUIREMENTS. REFER TOARCHITECTURAL DRAWINGS FOR PENETRATION THROUGH RATEDASSEMBLY (FLOORS AND WALLS) DETAILS.

6. PRIOR TO FINAL TURNOVER TO THE OWNER, ALL SINK AND LAVATORY FAUCETSAND FIXTURE FLUSH VALVES SHALL BE TESTED AND ADUSTED TO ENSUREPROPER OPERATION.

7. PROVIDE PIPE DRAINS AT LOW POINTS AND BALL VALVE AIR VENTS AT HIGHPOINTS OF DOMESTIC WATER SYSTEM.

8. DO NOT ROUTE PIPING THROUGH ELECTRICAL ROOMS OR COMMUNICATION ROOMS.ONLY PIPING SERVING ELECTRICAL ROOMS AND COMMUNCIATION ROOMS SHALLENTER THESE ROOMS.

9. DO NOT ROUTE PIPING OVER ELECTRICAL PANELS, SWITCHBOARDS, SWITCHGEAR,OR TRANSFORMERS.

10. PROVIDE WATER HAMMER ARRESTORS PDI SIZE "A" ON INDIVIDUAL COLD WATERPIPING SERVING WATER CLOSETS. LOCATE ARRESTOR ABOVE CEILING FOR ACCESS.ARRESTORS SHALL BE PROVIDED AT OTHER PLUMBING FIXTURES, LOCATED ANDSIZED IN ACCORDANCE WITH PDI STANDARD WH-201 AND ASSE 1010. SIZES INDICATEDARE THE MINIMUM SIZE PERMITTED. ACCESS PANELS SHALL BE PROVIDED FOR ALLARRESTORS LOCATED ABOVE NON-ACCESSIBLE CEILINGS AND WITHIN WALLS.

11. PROVIDE CLEANOUTS PER FLORIDA PLUMBING CODE.

12. REFER TO ARCHITECTURAL INTERIOR ELEVATIONS AND FLOOR PLANS FORDIMENSIONS OF ALL PLUMBING DEVICES, FIXTURES, AND DRAINS. ARCHITECTURALDEFINED DIMENSIONS TAKE PRECEDENCE OVER DIMENSIONS INDICATED ONENGINEERING PLANS. VERIFY ALL FIXTURE PLACEMENT DIMENSIONS PRIOR TOFIXTURE AND PIPING ROUGH-IN.

No 77673

STATE OF

RK S.ERED

PR

OF

NSSOI

ELA ENGIN

EER

LICENSE

F LO RIDA

EED

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS

DEREK STEPHEN REED - ME PE0077673

10/23

/2015

11:41

:3 4 A

M

PL001

PLUMBINGSYMBOLS ANDABBREVIATIONS

VLM

DSR


PLUMBING SPECIFICATIONS:

A. CODES: CONFORM TO REQUIREMENTS OF THE FOLLOWING CODES:

1. FLORIDA BUILDING CODE - PLUMBING, 2014 EDITION WITH AMENDMENTS/SUPPLEMENTS. 2. FLORIDA BUILDING CODE - BUILDING, 2014 EDITION WITH AMENDMENTS/SUPPLEMENTS.

B. FIELD CONDITIONS:

1. THE CONTRACTOR SHALL BECOME FAMILIAR WITH ALL DETAILS OF THE WORK, SHALL VERIFY ALL DIMENSIONS AT THE PROJECT SITE, AND SHALL ADVISE THE ARCHITECT OF ALL DISCREPANCIES BEFORE PERFORMING WORK.

2. BECAUSE OF THE SMALL SCALE OF THE CONTRACT DRAWINGS, IT IS NOT POSSIBLE TO INDICATE ALL OFFSETS, FITTINGS AND ACCESSORIES THAT MAY BE REQUIRED. THE CONTRACTOR SHALL INVESTIGATE THE PLUMBING WORK INCLUDING ALL FINISH CONDITIONS THAT COULD AFFECT THE WORK TO BE PERFORMED, AND SHALL ARRANGE SUCH WORK ACCORDINGLY, AND SHALL PROVIDE ALL WORK NECESSARY TO MEET SUCH CONDITIONS.

C. JOINT SEALERS: PROVIDE ACRYLIC BASE CAULKING MATERIAL FOR SEALING ANNULAR SPACES BETWEEN SLEEVES, PIPES AND THEIR ADJACENT SPACES.

1. PROVIDE FIRE RESISTANT JOINT SEALERS (FIRESTOPPING) FOR SEALING ANNULAR SPACES BETWEEN SLEEVES, PIPES, AND FIRE AND SMOKE RATED WALL, PARTITION, CEILING AND FLOOR ASSEMBLIES.

2. PREPARE SOIL WASTE AND VENT PIPING ACCORDING TO FLORIDA BUILDING CODE - PLUMBING AND AS FOLLOWS:

A. CONNECT TO EXISTING PIPING SYSTEMS WHERE INDICATED.

B. INSTALL CAST-IRON PIPE AND SOIL PIPE FITTINGS ACCORDING TO CISPI 1990 REVISED, AND EDITED EDITION OF "CAST IRON PIPE AND FITTINGS HANDBOOK", VOLUME 1, CHAPTER IV, "INSTALLATION OF CAST IRON SOIL PIPE FITTINGS".

C. MAKE CHANGES IN DIRECTION USING Y PATTERN BRANCHES WITH 1/8 BENDS AND LONG SWEEP 1/4, 1/5, 1/6, 1/8 AND 1/16 BENDS. INSTALL DRAINAGE PIPING 2-1/2 INCH DIAMETER AND LESS AT 1/4 INCH PER FOOT SLOPE (2 PERCENT) AND PIPING 3 INCHES DIAMETER AND GREATER AT 1/8 INCH PER FOOT (1 PERCENT). INSTALL VENT PIPING AT 1/8 INCH PER FOOT (1 PERCENT).

D. AFTER FLUSHING, PRESSURE TEST PIPING.

E. DO NOT ENCLOSE, COVER OR PUT INTO OPERATION, PIPING SYSTEMS UNTIL THEY HAVE BEEN INSPECTED AND APPROVED BY THE AUTHORITY HAVING JURISDICTION. DURING THE PROCESS OF INSTALLATION, NOTIFY THE PLUMBING OFFICIAL HAVING JURISDICTION AT LEAST 24 HOURS PRIOR TO THE INSPECTION TIME. PERFORM ALL TESTS IN THE PRESENCE OF THE PLUMBING OFFICIAL. RETEST AND ARRANGE FOR RE-INSPECTION WHEN PIPING SYSTEMS FAIL TO PASS TESTING AND INSPECTION. PREPARE WRITTEN REPORTS SIGNED BY THE PLUMBING OFFICIAL.

F. ROUGHING-IN INSPECTION: ARRANGE FOR INSPECTION OF PIPING SYSTEM BEFORE CONCEALING OR CLOSING-IN AND PRIOR TO SETTING OF PLUMBING FIXTURES.

3. TEST IN ACCORDANCE WITH FLORIDA BUILDING CODE - PLUMBING AND AS DIRECTED BY AUTHORITY HAVING JURISDICTION. LEAKS WHICH OCCUR IN EXISTING PIPING SYSTEMS AS A RESULT OF CONNECTIONS FROM NEW PIPING SHALL BE MADE BY THIS CONTRACTOR.

G. SOIL, WASTE, AND VENT PIPING:

1. MATERIALS: 1-1/2 TO 4 INCHES; CAST-IRON HUBLESS SOIL PIPE; CISPI 301, CAST IRON SOIL PIPE FITTINGS; CISPI 301. COUPLINGS FOR CAST-IRON SOIL PIPE FITTINGS SHALL BE CISPI 310, HAVING ASTM C 564 NEOPRENE SEALING SLEEVE WITH 300 SERIES STAINLESS STEEL CORRUGATED SHIELD AND CLAMP ASSEMBLY.

E. PLUMBING INSULATION:

1. INSULATION/COMPOSITE FACING SHALL HAVE A FLAME SPREAD OF NOT GREATER THAN 25 AND A SMOKE DEVELOPED RATING NOT EXCEEDING 50 WHEN TESTED IN ACCORDANCE WITH ASTM E 84, UL 723 AND NFPA 255 (2006). MOISTURE VAPOR TRANSMISSION SHALL BE NOT GREATER THAN 0.02 PERMS WHEN TESTED IN ACCORDANCE WITH ASTM E 96, METHOD A.

2. PIPE INSULATION:

A. TYPE P1: PREFORMED CYLINDRICAL PIPE INSULATION COMPOSED OF HIGH QUALITY GLASS FIBERS BONDED TOGETHER WITH A THERMOSETTING RESIN. THE INSULATION SHALL BE ONE PIECE FIBERGLASS PIPE INSULATION WITH A THERMAL CONDUCTIVITY (K-VALUE) OF 0.23 BTU-INCH/(HR-SQ.FT.-°F) AT 75°F MEAN TEMPERATURE. SECTIONS SHALL HAVE A SINGLE SEAM THAT OPENS TO RECEIVE THE PIPE AND SNAPS CLOSED AFTER IT IS IN PLACE. PROVIDE WITH A FACTORY APPLIED ALL SERVICE JACKET (ASJ). ACCEPTABLE MANUFACTURER: OWENS CORNING OR APPROVED EQUAL.

B. TYPE P2: CELLULAR GLASS INSULATION, ASTM C 552, TYPE II. INSULATION SHALL HAVE AVERAGE DENSITY OF 8 LB/CUBIC FT. AND WATER VAPOR PERMEABILITY OF 0.00 PERMS. THERMAL CONDUCTIVITY (K-VALUE), AT 32 DEGREES FAHRENHEIT, OF 0.31 BTU-INCH/(HR-SQ.FT.-°F). IMPERVIOUS TO COMMON ACIDS, EXCEPT HYDROFLUORIC ACID. NON- COMBUSTIBLE AND DIMENSIONALLY STABLE. PROVIDE WITH A FACTORY APPLIED ALL SERVICE JACKET (ASJ). ACCEPTABLE MANUFACTURER: PITTSBURGH CORNING OR APPROVED EQUAL.

D. HANGERS AND SUPPORTS:

1. FACTORY -FABRICATED ACCORDING TO MSS SP-58; COMPLY WITH MSS SP-69 AND MSS SP-89. PROVIDE CLEVIS TYPE HANGERS UNLESS NOTED OTHERWISE. INCLUDE ALL SUPPORT RODS, ATTACHMENTS TO STRUCTURE, ANCHORS AND ACCESSORIES TO PROPERLY SUPPORT PIPING FROM BUILDING STRUCTURE. INSTALL QUANTITY AND SPACE TO MAINTAIN UNIFORM PIPE ELEVATIONS WITHOUT SAGGING OR OTHER ABERRATIONS.

2. INSTALL HANGERS FOR HORIZONTAL POTABLE WATER AND SOIL PIPING UP TO 2 INCH DIAMETER AT A MAXIMUM SPAN OF FIVE FEET; PROVIDE 3/8 INCH DIAMETER THREADED HANGER RODS.

3. SUPPORT CAST-IRON SOIL PIPE AND CAST-IRON STORM WATER PIPING AT A MAXIMUM HORIZONTAL SPACING OF FIVE FEET, EXCEPT 10 FOOT SECTIONS OF PIPING MAY BE SUPPORTED AT 10 FEET SPACING; PROVIDE 3/8 INCH DIAMETER THREADED RODS. SUPPORT VERTICAL PIPING AT A MAXIMUM SPACING OF 15 FEET AND AT EACH FLOOR LEVEL.

1. MATERIALS: DRAWN-TEMPER COPPER TUBING; ASTM B 88, TYPE L.

2. PIPE FITTINGS: CAST COPPER PRESSURE FITTINGS, SOLDER JOINT, LONG RADIUS ASME B16.18 WITH ALLOY SN95 SILVER SOLDER.

3. PREPARE POTABLE WATER PIPING ACCORDING TO ASME B31.1 AND AS FOLLOWS:

A. LEAVE JOINTS UNINSULATED AND EXPOSED FOR EXAMINATION DURING TESTING. INSTALL PIPING WITHOUT PITCH.

B. CONNECT TO EXISTING PIPING SYSTEMS WHERE INDICATED.

C. REMOVE BURRS AND CONSTRUCTION DEBRIS.

D. FLUSH SYSTEM WITH CLEAN WATER AND CLEAN THOROUGHLY; ISOLATE EQUIPMENT THAT IS NOT SUBJECTED TO TEST PRESSURE FROM PIPING. VALVES USED IN EQUIPMENT ISOLATION SHALL BE CAPABLE OF SEALING AGAINST TEST PRESSURE WITHOUT DAMAGE TO VALVES OR EQUIPMENT.

E. AFTER FLUSHING, PRESSURE TEST PIPING.

F. DO NOT ENCLOSE, COVER OR PUT INTO OPERATION, PIPING SYSTEMS UNTIL THEY HAVE BEEN INSPECTED AND APPROVED BY THE AUTHORITY HAVING JURISDICTION. DURING THE PROCESS OF INSTALLATION, NOTIFY THE PLUMBING OFFICIAL HAVING JURISDICTION AT LEAST 24 HOURS PRIOR TO THE INSPECTION TIME. PERFORM ALL TESTS IN THE PRESENCE OF THE PLUMBING OFFICIAL. RETEST AND ARRANGE FOR RE-INSPECTION WHEN PIPING SYSTEMS FAIL TO PASS TESTING AND INSPECTION. PREPARE WRITTEN REPORTS SIGNED BY THE PLUMBING OFFICIAL.

G. ROUGHING-IN INSPECTION: ARRANGE FOR INSPECTION OF PIPING SYSTEM BEFORE CONCEALING OR CLOSING-IN AND PRIOR TO SETTING OF PLUMBING FIXTURES.

4. TEST POTABLE PIPING AS FOLLOWS:

A. VENT AIR AT HIGH POINTS WHEN FILLING SYSTEM; VOID SYSTEM OF ALL AIR.

B. EXAMINE SYSTEM TO SEE THAT EQUIPMENT AND PARTS THAT CANNOT WITHSTAND TEST PRESSURE ARE ISOLATED.

C. SUBJECT PIPING TO A PRESSURE OF 150 PSIG FOR A PERIOD OF FOUR HOURS. IF NO LOSS OF PRESSURE OCCURS THE TEST IS SUCCESSFUL. IF THE PRESSURE DROPS DURING TESTING, STOP TEST, DRAIN PIPING, MAKE REPAIRS. REPEAT TEST PROCEDURE UNTIL SUCCESSFUL. PROVIDE PUMP AND TEMPORARY PIPING TO ENABLE TESTING. REPAIRS OF LEAKS WHICH OCCUR IN EXISTING PIPING SYSTEMS AS A RESULT OF CONNECTIONS FROM NEW PIPING SHALL BE MADE BY THIS CONTRACTOR.

5. PIPE CLEANING:

A. PURGE AND DISINFECT IN ACCORDANCE WITH FLORIDA BUILDING CODE - PLUMBING AND AUTHORITY HAVING JURISDICTION. PURGE NEW POTABLE WATER PIPING AND PARTS OF EXISTING POTABLE WATER PIPING THAT HAVE BEEN CONNECTED TO, ALTERED, EXTENDED OR REPAIRED, PRIOR TO USE. USE AWWA C651 OR AWWA C652 AS A MINIMUM.

F. POTABLE WATER PIPING:

No 77673

STATE OF

RK S.ERED

PR

OF

NSSOI

ELA ENGIN

EER

LICENSE

F LO RIDA

EED

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

11:41

:3 5 A

M

PL002

PLUMBINGSPECIFICATIONS

VLM

DSR

1


1 ADDENDUM 1 10-23-15

43

2

1

151E1093

CLASSROOM146

1/2"CW

(E)2"SAN2"SANL-1

CLASSROOM149

5

5 5

5

5

5

L-1 LAVATORY

MARKPLAN DESCRIPTION MANUF. / MODEL No.

1. WALL MOUNTED, ADADRILLED FOR CONCEALED ARM CARRIER, 8" CENTERSVITREOUS CHINA, WHITE.

2. FAUCET: DECK MOUNTED WITH 8"CENTERS, SWIVEL GOOSENECK,4" WRIST ACTION HANDLES, 2.2 GPM

T & S BRASS B-2866-05

3.

TRAP: 1-1/4" X 1-1/2" CHROME PLATED. CAST BRASS. TO BE PROVIDED UNDERADD ALTERNATE 2 -PLUMBING.

5. SUPPLY: 1/2" X 3/8" BRASS LOOSE KEY STOP, WITH ANNEALEDVERTICAL TUBE AND ESCUTCHEON. TO BE PROVIDED UNDER ADDALTERNATE 2 -PLUMBING.

6.

FLOOR MOUNTED CARRIER WITH CONCEALED ARMS. ZURN Z12314. DRAIN: CHROME PLATED BRASS GRID DRAIN WITH PLUG UNDER BASE BID.

PROVIDE CHROME PLATED BRASS GRID DRAIN WITH OFFSET TAIL PIECEASSEMBLY FOR WHEEL CHAIR ACCESS, 17 GA, UNDER ADD ALTERNATE 2 -PLUMBING.

MCGUIRE

MCGUIRE

MCGUIRE

5905.100

AMERICAN STANDARDLUCERNE 0356.015

PLUMBING FIXTURE SPECIFICATIONS

CARRIERLAVATORY

4" WRIST BLADE HANDLES

GOOSENECK SPOUTFINISHED WALL

1/2" CW & HWSUPPLIES WITH STOP.INSULATE CW & HWSUPPLIES.(ADD ALTERNATE 2- PLUMBING)

1-1/4" WASTE &"P" TRAPINSULATED(ADD ALTERNATE 2- PLUMBING)

BEARINGPLATE

BLOCK BASEPLATES

FINISHED FLOOR

No 77673

STATE OF

RK S.ERED

PR

OF

NSSOI

ELA ENGIN

EER

LICENSE

F LO RIDA

EED

0 5'


10' 20' 30'

N

KEY NOTES :NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

11:41

:2 4 A

M

B1-PL101

BUILDING 1PLUMBING PLAN

VLM

DSR

1/8" = 1'-0"1 BUILDING 1 FLOOR PLAN - PLUMBING

1 EXISTING ELECTRICAL WATER COOLER.

2 2"V UP TO EXISTING 2" VTR.

3 PROVIDE 2" STUDOR VENT IN WALL ABOVEFLOOD RIM OF LAV. PROVIDE ACCESS PANELON BACK SIDE FOR MAINTENANCE OF STUDORVENT.

4 PROVIDE 3 WAY ANGLE STOP VALVE. CONNECT TOLEFT AND RIGHT FAUCET HANDLE.

5 WORK TO BE DONE UNDER ADD ALTERNATE 2- PLUMBING.

NOT TO SCALE2 TYPICAL CARRIER DETAILS


F

B

T

TO BE REMOVEDR

FIRE DEPARTMENT CONNECTIONFDC

THERMOSTATIC STEAM TRAP

(3/4" BALL VALVE AND CAP)STRAINER - Y PATTERN WITH BLOWDOWN

THERMOMETER

VENTURI FLOW METER

STRAINER - Y PATTERN

INVERTED BUCKET STEAM TRAP

FLOAT AND THERMOSTATIC STEAM TRAP

THERMODYNAMIC STEAM TRAP

PRESSURE GAGE W/SNUBBER

DIRECTION OF PIPING PITCH

FLEXIBLE CONNECTION - ELASTOMERIC

FLEXIBLE CONNECTION - BRAIDED

PRESSURE GAGE

DIRECTION OF FLOW

V

SW

P(LPG)

R

FLAT OVAL DUCT IN SECTION

RECTANGULAR DUCT, FIRST

STANDARD BRANCH TAKEOFF

TRANSITION - CONCENTRIC

TRANSITION - ECCENTRIC

ROUND DUCT, DIAMETER SHOWNLEAF TYPE

FLEXIBLE CONNECTION

MOTOR ACTIVATED CONTROL DAMPER

BLADE TYPE (UNLESS NOTED OTHERWISE)MANUAL DAMPER - OPPOSED

MANUAL DAMPER - SINGLE

TEE TURNED DOWN

TEE TURNED UP

ELBOW TURNED DOWN

ELBOW TURNED UP

EXHAUST AIR DUCT - SECTION

RETURN AIR DUCT - SECTION

DIMENSIONS SHOWN

12"Ø

24X12Ø

FLEXIBLE DUCT

FIGURE IS SIDE SHOWN24X12

LINEAR SLOT DIFFUSER

HARD CEILING EQUIPMENT ACCESS PANEL

HUMIDIFIER

TOP/SIDE/BOTTOMDUCT ACCESS DOOR

FIRE DEPARTMENT VALVE

FLOOR MOUNTED

FINISHED FLOOR ELEVATION

FEET PER MINUTEFEET PER SECOND

FIRE/SMOKE DAMPER

GALLONS PER HOUR

GRAVITY INTAKE VENTILATOR

CEILING DIFFUSER - BOTTOM

TURNING VANES - SQUARE ELBOW

OFFSET IN DUCTWORK - DOWN

OFFSET IN DUCTWORK - UP

HUMIDISTAT

PRESSURIZATION SENSOR

THERMOSTAT/TEMPERATURE SENSOR,

SMOKE DETECTOR

EXHAUST AIR REGISTER

RETURN AIR REGISTER/GRILLE

SQUARE SUPPLY AIR DIFFUSER

SUPPLY AIR DUCT - SECTION

DN

DUCT CONNECTION

UP

FLOW METERING ORIFICE

PROPANE (LIQUEFIED PETROLEUM GAS)

VENT

DOMESTIC SOFT WATER

PUMP CIRCULATION

FLUSH VALVEFV

GPH

GIVGNGLV

GFW

GLOBE VALVEGENERATOR

GRILLE, GASFIRE WATER

FSF/SD

FOFPMFPS

FLOOR SINK

FLAT OVAL

FH

FMFL

FFEFDV

FIRE HYDRANTFLOOR(ING)

SMOKE DAMPERCOMBINATION FIRE/

FIRE DAMPERSVERTICAL POSITION

VERTICAL POSITION

HORIZONTAL POSITION

HORIZONTAL POSITION

F/SD

F/SD

REFRA

RFRH

REG

RORR

RHC

RWLRTU

RAIN WATER LEADERROOF TOP UNIT

REVERSE OSMOSISREHEAT COIL

RETURN AIR REGISTER

RETURN FAN

RETURN AIR

REHEAT, RELATIVE HUMIDITY

REGISTERREFERENCE

FWS

PRESSURE REDUCING/REGULATING

AUTOMATIC AIR VENT W/BALL VALVE

EXPANSION LOOP

AIR VENT - MANUAL

ALIGNMENT PIPE GUIDES

ANCHOR - PIPING

TRIPLE DUTY

SAFETY RELIEF

OFL

PC

MPS (70)

LPS (5)

MPC

LPC

HWR

HWS

HRS

HRR

HPS (100)

HPC

GAS COCK

POST INDICATOR

BLOW-DOWN

FLOW BALANCING

TWO-WAY CONTROL VALVE

THREE-WAY CONTROL VALVE

CWS

FOR

FOV

FOS

FOG

D

CHWS

CWR

CHWR

CW

CR

PLUG - SQUARE HEAD COCK

GLOBE - ANGLE PATTERN

GLOBE

CHECK - SPRING LOADED

CHECK - SWING GATEGATE

BUTTERFLY

BALL

BFS

CBO

MCWR

CF

MCWS

CA

BO

BF

A

SWITCH, SOFT WATER

CELSIUS, DEGREE CELSIUS

CONDENSATE PUMP UNIT

CEILING DIFFUSER

CUBIC FEET PER MINUTE

CHILLED WATER

CONDENSING UNITCOOLING TOWERCOLD SOFT WATERCOMPUTER ROOM UNIT

DEAERATOR, DENTAL AIR, DAMPER ACTIVATOR

DIRECT DRIVE, DECK DRAIN, DUAL DUCT

ENCLOSE (ENCLOSURE)

EXISTING TO REMAIN

ENTERING AIR TEMPERATUREELECTRIC CONTROL DAMPER

EXTERNAL STATIC PRESSURE

FLOOR CLEAN OUT

ETHYLENE OXIDE

FIRE DAMPER, FLOOR DRAIN

EXPANSION TANK

EXHAUST REGISTER

COMPUTER ROOM AIR CONDITIONER

ENTERING WATER TEMPERATURE

DRAIN, WASTE AND VENT PIPING

FAHRENHEIT, DEGREE FAHRENHEIT/FILTER

DUCT HEATERDH

FEED WATER SAMPLE

AIR QUANTITY

AIR QUANTITY(CFM)

SCHEDULE REFERENCE

EQUIPMENT TYPE

SPOOL PIECE - FLANGED

VALVE IN RISER

AIR VALVE SCHEDULE

PUMPED CONDENSATE

MEDIUM PRESSURE STEAM (PSIG)

OVER FLOW

LOW PRESSURE CONDENSATE

MEDIUM PRESSURE CONDENSATE

LOW PRESSURE STEAM (PSIG)

3.1300

REFERENCE

HEAT RECOVERY SUPPLY

HOT WATER RETURN

HOT WATER SUPPLY

HEAT RECOVERY RETURN

HIGH PRESSURE CONDENSATE

HIGH PRESSURE STEAM (PSIG)

CD-A100

TYPE

ER

GRILLE MARK}

} AIR VALVE MARK

}

FDFCOFCU

FFA

FAN COIL UNIT

FIRE ALARM

ETOEWTEXH

ETESP

EXHAUST

DIFFUSER, REGISTER,EF EXHAUST FAN

ENCLENT

EFFELEV

ENTERING

EFFICIENCYELEVATION

EAEATECD

EDWV

EXHAUST AIR

LATERAL

PLUGGED LINE

BLIND FLANGED CAP

CAPPED LINE

REDUCER - ECCENTRIC, STRAIGHT INVERT

REDUCER - ECCENTRIC, STRAIGHT CROWN

REDUCER - CONCENTRIC

UNION - GROUND JOINT

TEE (TURNED DOWN)

TEE (TURNED UP)

CONDENSER WATER SUPPLY

FUEL OIL RETURN

FUEL OIL VENT

FUEL OIL SUPPLY

FUEL OIL GAGE

DRAIN

CONDENSER WATER RETURN

CHILLED WATER RETURN

CHILLED WATER SUPPLY

DOMESTIC COLD WATER

CONDENSATE RETURNTEE

DA

DGDEG

DBDD

DEGREEDOOR GRILLE

DRY BULB

CTCUCW

CSWCRU

COLD WATER

CFM

CO

CI

CPU

CHCHW

CLEAN OUT

CAST IRON

CHILLER

CBCDCENT

CACCAP

CATCH BASIN

CENTRIFUGAL

CAPACITY

VENT THROUGH ROOF

NC NOISE CRITERIA, NORMALLY CLOSED

VTR

NATIONAL PIPE TREAD STANDARDNORMALLY OPEN, NITROUS OXIDE

POUNDS PER SQUARE INCH GAUGE

PRESSURE REDUCING VALVE, PRESSURE REGULATING VALVE,

PCV PNEUMATIC CONTROL VALVEPDIPH

PROPPRS

PIV

PRV

PSI

PVCPSIG

POWER ROOF VENTILATOR

POLYVINYL CHLORIDE

POUNDS PER SQUARE INCH

POST INDICATOR VALVE

PLUMBING DRAIN INSTITUTE

PRESSURE REDUCING STATIONPROPELLER

PHASE

NPTSNO

OBDOA

OE

OPER

PCD

OD

P

O

OVERFLOW DRAINORAL EVACUATION

PNEUMATIC CONTROL DAMPERPUMPOPERATING

OPPOSED BLADE DAMPEROUTSIDE AIROXYGEN

WET BULB

WATER METER

WALL CLEANOUTWATER CLOSET

WELDED WIRE FABRIC

WALL HYDRANT

WATER PRESSURE DROPWM

WWFWPD

WC

WHWCO

WWB

WASTE

LEAVING WATER TEMPERATUREMALWT

MEDMDMBH

M/SMM

MV

MH

N

MANHOLE

MEDICAL VACUUMMETERS PER SECONDMILLIMETERS

NITROGEN

MEDICAL AIRTHOUSAND BTU PER HOURMANUAL DAMPERMEDICAL

HXHZ

IPS

INV

LA

LD

LV

LEDLFD

KW

ID

KILOWATT

LABORATORY VACUUM

LIGHT EMITTING DIODE

LABORATORY AIR (30 PSI)

LAMINAR FLOW DIFFUSER

LINEAR DIFFUSER

IRON PIPE SIZE

INDIRECT DRAIN

HEAT EXCHANGERHERTZ (CYCLES PER SECOND)

INVERT

UP BLOWUNIT HEATER

VENT, VOLT

TOTAL STATIC PRESSURE

VOLUME DAMPERVACUUM BREAKER

TREATED WATER

URINALUR

VDVB

VVAC VACUUM

UB

UNUH

UNION

TWTSP

TRENCH DRAIN

TRAP PRIMERTHERMOMETER

TEMPERATURE

TAMPER SWITCHTHERMOSTATIC MIXING VALVE

TEMPORARY EXHAUST FAN

SECURITY WALL PENETRATIONSECURITY WALL BARRIER

TANK, THERMOSTAT

TRANSFER GRILLETEMP

TS

TPTMV

THTG

T

TDTEF

SWPSWB

AIR CONDITIONING UNIT

BALANCING VALVE

BACKFLOW PREVENTER

ABOVE FINISHED GRADEAIR HANDLING UNITACCESS PANEL

BACK DRAFT DAMPER

BRITISH THERMAL UNIT

AUTOMATIC TEMPERATURE CONTROL

ALTERNATING CURRENT, AIR COMPRESSOR

ACCESS DOOR, AIR DRYER, AREA DRAIN, AIR DAMPER

FLANGED

ELBOW (45°)

ELBOW (90°)

ELBOW (BASE)

ELBOW (TURNED DOWN)

ELBOW (TURNED UP)

SCREWED/SOLDERED/WELDEDBOILER FEED PUMP SUCTION

CONTINUOUS BOILER BLOWOFF

CHEMICAL FEED

MRI COOLING WATER RETURN

MRI COOLING WATER SUPPLY

COMPRESSED AIR

BLOWOFF

COMPRESSED AIR

BOILER FEEDWATER

BOILER, DDC SYSTEM BACKBONE CABLEB

BVC

BTUBPBDD

AHUAPATC

AD

AFG

ACACU

HIGH PRESSURE COLD WATER (DOMESTIC)

HEATING/VENTILATING/AIR CONDITIONING

HDHC

HORHOAHE

HSWHPCW

HVACHWHWR

HP HORSEPOWER, HEAT PUMP

HOT SOFT WATER

HOT WATER, HEATING WATERHOT WATER RETURN

HORIZONTAL

HEAT EXCHANGER

HANDICAPPED

HAND-OFF-AUTOMATIC

HUB DRAIN

HBH

HOSE BIBBHUMIDIFIER

SMOKE/FIRE DAMPERS/FD

SPRINKLER

STRAINER

SERVICE SINK

STANDPIPE, STATIC PRESSURE

SUPPLY GRILLE

SIDEWALL SUPPLY REGISTER

SIDEWALL TRANSFER GRILLE

SIDEWALL REGISTERSS

SWSTRSTGST

SSR

STORM

SP

SRRSPKR

SHSG

SHOWER

SUPPLY FANSF

DAMPER ACCESS AREA

TD

MV

AV

S

EF1

DESIGN CONDITIONS:

DUCTWORK

VALVES - SPECIAL DUTY

PIPING SPECIALTIES

VALVES

SYMBOLS

GENERAL IDENTIFICATION

PIPE FITTINGSHVAC PIPING

ABBREVIATIONS

H

T

SD

OUTSIDE:

INDOORS:

SUMMER:WINTER:

88°F db, 78°F wb38°F db

CONSTRUCTIONPOINT OF CONNECTION EXISTING TO NEW

POINT OF REMOVAL - DEMOLITION

(MAKE-UP WATER)

(MAKE-UP WATER)

REMOTE DAMPER ACTUATORS

ABOVE FINISHED FLOORAFF

AUDIBLE VISUAL ALARMA

ROOM PRESSURE SENSOR MONITORPM

ALL AREAS: 75°F db +/- 5°F, 20-60% RH

TRANSFER AIR DUCTTAD

VALVEVLV

CN CONTACTORLAN LOCAL AREA NETWORK

AIR BLENDERAB

BUILDING CONTROL NETWORKBCN

IP DDC INPUT POINT

OP DDC OUTPUT POINT

VAV VARIABLE AIR VOLUME

CAV CONSTANT AIR VOLUME

SER SIDEWALL EXHAUST REGISTERSRR SIDEWALL RETURN REGISTERSSR SIDEWALL SUPPLY REGISTER

GREASE WASTE

GALLONS PER MINUTEGRAVITY RELIEF VENTILATORGRV

GWGTV

GPM

GATE VALVESMOKE DAMPER, SMOKE DETECTOR,

SOILS

SANSA

SDSTORM DRAIN

SUPPLY AIRSANITARY

GALLONS PER HOURGPHGLV GLOBE VALVE

S

POINT OF CONNECTION BETWEEN NEW AND

EXISTING PIPING, DUCTWORK AND EQUIPMENT

POINT OF DEMOLITIONEXISTING CONSTRUCTION

TO REMAIN (SCREENED)

F/O

A

BCN

BCW

EP

SW

LSC

CO2

CT

FT

TP

RL

SV

FACM

PB

PS

CTC

DMP

MC

VMP

ES

FM

CS

RS

SL

PL

RHL

CONTROLS SYMBOLS

NORMALLY CLOSED DEVICE ON POWER FAILUREN.C.

CONTACTOR

ELECTRIC/PNEUMATIC SWITCH

SWITCH SPST

PROBE TYPE LEVEL SENSOR

20 PSIG CONTROL AIR

DIGITAL CONTROLLER MARK(DDC SYSTEM) CONTROLLERNUMBER

DATA GATHERING PANEL MARK(REFER TO SPECIFICATIONS)PANEL NUMBER

DGP-XX

DC-XX

20

NORMALLY OPEN DEVICE ON POWER FAILURE

BUILDING CONTROL NETWORK CABLE

90% AIR FILTER SECTION

PNUEMATIC AIR

FIBER OPTIC COMPUTER CABLE

N.O.

CONTROL DAMPER

AIR FILTER SECTION

PUMP

FAN

HEAT TRANSFER COIL

EQUIPMENT (DIV 22 OR 23)

DIFFERENTIAL PRESSURE TRANSDUCER

TEMPERATURE/HUMIDITY SENSOR

DAMPER MOTOR - ELECTRIC

VALVE MOTOR - ELECTRIC

HUMIDITY SENSOR

DIFFERENTIAL PRESSURE SWITCH

VM

DM

HS

TS

DPT

DPS

VARIABLE FREQUENCY DRIVE (DIV 26)

MAGNETIC MOTOR STARTER (DIV 26)

POWER CONTACTOR INTEGRAL TO

MANUAL MOTOR STARTER (DIV 26)

CN

SM

STR

VFD

FD FIRE DAMPERF/SD FIRE/SMOKE DAMPER

CARBON DIOXIDE MONITORS

RELAY

SOLENOID VALVE

CURRENT TRANSDUCER

FREEZE THERMOSTAT

PNEUMATIC ROOM THERMOSTAT

AIR BLENDER

UVC EMITTERS

STEAM HUMIDIFIER

FIRE ALARM CONTROL MODULE

PUSH BUTTON

PRESSURE SENSOR

ELECTRONIC/PNEUMATIC TRANSDUCER

CONDUCTIVITY CONTROLLER

HUMIDIFIER

SPRING WOUND TIMER

VALVE MOTOR - PNUEMATIC

DAMPER MOTOR - PNUEMATIC

MOTOR CONTACTOR

HDF

EPT

TM

INSTALLED BY DIV 23

STATIC PRESSURE HIGH LIMIT

AIRFLOW MEASURING STATION

SMOKE/FIRE DAMPER

VELOCITY SENSOR

DUCT SMOKE DETECTOR (DIV 26)

STATIC PRESSURE TRANSDUCER

SFD

VPS

FMS

SPL

SPT

SD

ELECTRONIC PROBE WATER SENSOR

BACKBONE CABLE FOR DDC SYSTEM

FOH FIBER OPTIC HUB

SOLENOID VALVE

VALVE

DOMESTIC COLD WATER

FLOW METER

CURRENT SENSOR

REFRIGERANT SENSOR

SMOKE LIGHT AND HORN

NEON PILOT LIGHT

RELATIVE HUMIDITY HIGHLIMIT SWITCH

FOR DDC SYSTEM

RL REFRIGERANT LIQUIDRS REFRIGERANT SUCTION

EQUIPMENT MARK

STAINLESS STEELSST

TERMINAL AIR VALVE WITHELECTRIC REHEAT COIL

FB FAN POWERED BOX

No 77673

STATE OF

RK S.ERED

PR

OF

NSSOI

ELA ENGIN

EER

LICENSE

F LO RIDA

EED

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

11:41

:3 0 A

M

MH001

MECHANICALSYMBOLS ANDABBREVIATIONS

VLM

DSR


6. THE TEST AND BALANCE SUBCONTRACTOR MUST REVIEW AND REPORT ANY

FURNISHING OF THE BUILDING RESULTING FROM THE ORIGINAL DEFECT OR REPAIRS. RECONSTRUCTION AND REPAIRS SHALL INCLUDE ALL DAMAGE TO THE FINISH OR AT HIS OWN EXPENSE TO THE ENTIRE SATISFACTION OF THE OWNER. SUCH THE ABOVE MENTIONED PERIOD MUST BE IMMEDIATELY MADE GOOD BY THE CONTRACTOR 2. DEFECTS OF ANY KIND DUE TO FAULTY WORK OR MATERIALS APPEARING DURING

CONDITION OF THE PERIOD OF ONE (1) YEAR AFTER SUBSTANTIAL COMPLETION DATE. OF WORK, EQUIPMENT AND MATERIALS AND KEEP SAME IN PERFECT REPAIR AND 1. THE CONTRACTOR SHALL WARRANTY/GUARANTEE AND MAINTAIN THE STABILITY

I. WARRANTY/GUARANTEE:

OPERATION AS INDICATED. ACCOMPLISH WORK IN ACCORDANCE WITH AABC

ACCORDANCE WITH THE DETAILED PROCEDURES OUTLINED IN THE REFERENCED 2. PERFORM TESTING AND BALANCING PROCEDURES ON EACH SYSTEM IDENTIFIED, IN

PERFORMANCES WHEN SYSTEMS CANNOT BE SUCCESSFULLY BALANCED. 4. PREPARE REPORT OF RECOMMENDATIONS FOR CORRECTING UNSATISFACTORY MECHANICAL

5. FINAL REPORT SHALL BE REVIEWED AND APPROVED BY THE ENGINEER OF RECORD.

NEW AND EXISTING SYSTEMS IN ACCORDANCE WITH, AND ON THE FORMS RECOMMENDED 3. RECORD ALL DATA OBTAINED DURING THE TESTING, ADJUSTING, AND BALANCING OF

EXHAUST SYSTEMS, AND VERIFY TEMPERATURE CONTROL SYSTEM

H. TESTING, ADJUSTING, AND BALANCING:

AND BALANCE NEW AND EXISTING SUPPLY AIR SYSTEMS, RETURN AIR SYSTEMS, ACCOMPLISH SYSTEMS AIR BALANCING, AND TESTING. TEST, ADJUST 1. PROVIDE MATERIALS, EQUIPMENT, LABOR AND SUPERVISION NECESSARY TO

BY THE REFERENCED STANDARDS.

PUBLICATIONS.

STANDARDS.

DEFICIENCIES OR SIGN OFF ON THE CONTRACT DOCUMENTS AND SHOP

1. INSULATION COMPOSITE/FACING SHALL HAVE A FLAME SPREAD NOT GREATER THAN 25 AND A SMOKE DEVELOPED RATING NOT EXCEEDING 50 WHEN TESTED IN ACCORDANCE WITH ASTM E 84, UL 723, AND NFPA 255. MOISTURE VAPOR TRANSMISSION SHALL NOT BE GREATER THAN 0.02 PERMS WHEN TESTED IN CONFORMANCE WITH ASTM E 96, METHOD A.

TOGETHER WITH A FIRE RETARDANT ADHESIVE. ASTM C 1136, TYPE II FSK. PROVIDE

BLANKET TYPE INSULATION COMPOSED OF GLASS FIBERS BONDED TOGETHER WITH A THERMOSETTING

A GLASS SCRIM REINFORCED LAMINATE OF ALUMINUM FOIL AND KRAFT PAPER BONDED

WITH A NORMAL R-VALVE OF 7.7 HR-SQ.FT.-°F/BTU AT 75°F MEAN TEMPERATURE. 3. DUCT INSULATION, TYPE D1; ASTM C 553, TYPE I, CLASS B-3, 1.0 LBS/CUBIC FT. DENSITY,

ADHESIVE AND SEALANT AS RECOMMENDED BY MANUFACTURER.

RESIN AND FACED WITH A FACTORY APPLIED FOIL SCRIM KRAFT (FSK) FACING. FSK SHALL BE

D. MECHANICAL INSULATION:

A. DUCT INSULATION: SUPPLY AIR DUCTS, 2 INCHES THICK; RETURN AIR DUCTS, 2 INCHES THICK; OUTSIDE AIR DUCTS, 2 INCHES THICK.

2. CONTRACTOR SHALL REPLACE OR REPAIR EXISTING DUCT AND PIPE INSULATION AFFECTED BY DEMOLITION AND CONNECTION POINTS FOR EXTENSION OF NEW SERVICES.

6. THE ENTIRE SYSTEMS AND ALL COMPONENTS SHALL HEREIN MEET ALL STATE, COUNTY AND LOCAL CODES AND ORDINANCES IN EVERY RESPECT.

SUCH WORK ACCORDINGLY, AND SHALL PROVIDE ALL WORK NECESSARY TO MEET CONDITIONS THAT COULD AFFECT THE WORK TO BE PERFORMED, SHALL ARRANGE

5. BECAUSE OF THE SMALL SCALE OF THE DRAWINGS, IT IS NOT POSSIBLE TO INDICATE ALL OFFSETS, FITTINGS, AND ACCESSORIES THAT MAY BE REQUIRED. THE CONTRACTOR SHALL INVESTIGATE THE MECHANICAL, ELECTRICAL, AND FINISH

4. VERIFICATION OF DIMENSIONS: THE CONTRACTOR SHALL BECOME FAMILIAR WITH ALL DETAILS OF THE WORK, SHALL VERIFY ALL DIMENSIONS IN THE FIELD, AND SHALL ADVISE THE ARCHITECT OF ALL DISCREPANCIES BEFORE PERFORMING

DRAWINGS. ELECTRICAL, AND CAPACITY DATA AND PIPING AND ELECTRICAL CONNECTION NOTED ON DRAWINGS. PROVIDE SINGLE LINE DIAGRAMS, DIMENSIONAL,

ARE REQUIRED.

MATERIALS.

3. PREPARE COORDINATION DRAWINGS, DETAILING MAJOR ELEMENTS, COMPONENTS AND

LOCATIONS AND CLEARANCES REQUIRED. 2. PREPARE AND SUBMIT FABRICATION DRAWINGS OF MECHANICAL SYSTEMS. INDICATE

A. INDICATE COMPLIANCE WITH CAPACITY DATA AND OPTIONAL EQUIPMENT

1. ALL DIVISION 23 PRODUCT DATA AND MANUFACTURER EQUIPMENT SHOP DRAWINGS

SYSTEMS OF MECHANICAL EQUIPMENT IN RELATIONSHIP WITH OTHER SYSTEMS AND BUILDING COMPONENTS.

A. INDICATE THE PROPOSED LOCATIONS OF PIPING, DUCTWORK, EQUIPMENT AND

C. COORDINATION:

SUCH CONDITIONS.

ANY WIORK.

I. MECHANICAL SPECIFICATIONS:

B. SUBMITTALS:

1. DISCONNECT, DEMOLISH, AND REMOVE WORK AS INDICATED.

A. DEMOLITION:

OR DISTURBED, REMOVE DAMAGED PORTIONS AND INSTALL NEW PRODUCTS OF 2. WHERE PIPE, DUCTWORK, INSULATION, OR EQUIPMENT TO REMAIN IS DAMAGED

EQUAL CAPACITY AND QUALITY. 3. ACCESSIBLE WORK: REMOVE INDICATED PIPE AND DUCTWORK IN ITS ENTIRETY.

4. REMOVAL: REMOVE INDICATED EQUIPMENT FROM THE PROJECT SITE.

AND MAKE OPERATIONAL EQUIPMENT INDICATED FOR RELOCATION. 5. TEMPORARY DISCONNECTION: REMOVE, STORE, CLEAN, REINSTALL, RECONNECT,

EQUIPMENT AND WITH OTHER INSTALLATIONS (NEW AND EXISTING). 2. COORDINATE LAYOUT AND INSTALLATION OF DUCTWORK AND PIPING WITH

1. COORDINATE DUCT AND PIPE SLEEVE INSTALLATION FOR WALL AND ROOF PENETRATIONS.

1. RECTANGULAR DUCTWORK: GALVANIZED SHEET STEEL; LOCK-FORMING QUALITY, ASTM A 527, COATING

3. JOINT AND SEAM SEALANT: ONE-PART, NONSAG, SOLVENT-RELEASE-CURING, POLYMERIZED BUTYL

DESIGNATION G 90. FABRICATE RECTANGULAR DUCTS IN ACCORDANCE WITH SMACNA "HVAC CONSTRUCTION STANDARDS," TABLES 1-3 THROUGH 1-19, INCLUDING THEIR ASSOCIATED DETAILS. CONFORM TO THE REQUIREMENTS IN THE REFERENCED STANDARD FOR METAL THICKNESS, REINFORCING TYPES AND INTERVALS, TIE ROD APPLICATIONS, AND JOINT TYPES AND INTERVALS.

SEALANT. TYPE I; FORMULATED WITH A MINIMUM OF 75 PERCENT SOLIDS. SEAL ALL TRANSVERSE JOINTS, LONGITUDINAL SEAMS, AND DUCT PENETRATIONS.

E. METAL DUCTWORK:

1 INCH STATIC PRESSURE RATING, POSITIVE DUCT PRESSURE, 1 INCH TEST PRESSURE. 2. STATIC PRESSURE CLASSIFICATION:

EXHAUST AIR DUCT; LOW DUCT CLASS, 1 INCH STATIC PRESSURE RATING, NEGATIVE PRESSURE, 1 INCH TEST PRESSURE. OUTSIDE AIR DUCT 1 INCH STATIC PRESSURE RATING, NEGATIVE

A. FABRICATE RECTANGULAR DUCTS IN LENGTHS APPROPRIATE TO REINFORCEMENT AND RIGIDITY CLASS REQUIRED FOR PRESSURE CLASSIFICATION.

B. FABRICATE ELBOWS, TRANSITIONS, OFFSETS, BRANCH CONNECTIONS, AND OTHER DUCT CONSTRUCTION IN ACCORDANCE WITH SMACNA "HVAC METAL DUCT CONSTRUCTION STANDARD", FIGURES 2-1 THROUGH 2-10.

A. SEAL ALL DUCTS IN ACCORDANCE WITH SMACNA SEAL CLASS A.

5. FLANGED JOINT MASTICS: ONE-PART, ACID-CURING, SILICONE ELASTOMERIC COMPLYING WITH ASTM C 920, TYPE S, GRADE NS, CLASS 25, USE 0.

6. HANGERS AND SUPPORTS: INSTALL RIGID ROUND AND RECTANGULAR METAL DUCT WITH SUPPORT SYSTEMS INDICATED IN SMACNA "HVAC DUCT CONSTRUCTION STANDARDS," TABLES 4-1 THROUGH 4-3 AND FIGURES 4-1 THROUGH 4-8. SUPPORT

G. DUCT ACCESSORIES:

HORIZONTAL DUCTS WITHIN 2 FEET OF EACH ELBOW AND WITHIN 4 FEET OF EACH

7. WIPE DOWN DUCT SYSTEMS PRIOR TO FINAL ACCEPTANCE TO REMOVE DUST AND DEBRIS.

BRANCH INTERSECTION.

1. MANUAL VOLUME CONTROL DAMPERS: PROVIDE FACTORY_FABRICATED VOLUME_CONTROL DAMPERS, COMPLETE WITH REQUIRED HARDWARE AND ACCESSORIES. STIFFEN DAMPER BLADES TO PROVIDE STABILITY UNDER OPERATING CONDITIONS. PROVIDE LOCKING DEVICE TO HOLD SINGLE_BLADE DAMPERS IN A FIXED POSITION WITHOUT VIBRATION. CLOSE DUCT PENETRATIONS FOR DAMPER COMPONENTS TO SEAL DUCT CONSISTENT WITH PRESSURE CLASS. PROVIDE END BEARINGS OR OTHER SEALS FOR DUCTS WITH PRESSURE CLASSIFICATIONS OF 3 INCHES OR HIGHER. EXTEND AXLES FULL LENGTH OF DAMPER BLADES. PROVIDE BEARINGS AT BOTH ENDS OF OPERATING SHAFT.

A. STANDARD VOLUME CONTROL DAMPERS: MULTIPLE OR SINGLE BLADE, PARALLEL OR OPPOSED BLADE DESIGN AS INDICATED, STANDARD LEAKAGE RATING, WITH LINKAGE OUTSIDE OF AIR STREAM, AND SUITABLE FOR HORIZONTAL OR VERTICAL APPLICATIONS.

B. STEEL FRAMES: HAT_SHAPED, GALVANIZED_STEEL CHANNELS, MINIMUM OF 16 GAGE, AND WITH MITERED AND WELDED CORNERS. PROVIDE FRAMES WITH FLANGES WHERE

C. ROLL FORMED STEEL BLADES: 16 GAGE GALVANIZED STEEL.

INDICATED FOR ATTACHING TO WALLS. PROVIDE FLANGELESS FRAMES WHERE INDICATED FOR INSTALLATION IN DUCTS.

D. BLADE AXLES: GALVANIZED STEEL.

E. TIE BARS AND BRACKETS: GALVANIZED STEEL.

F. DAMPER CONTROL HARDWARE: ZINC PLATED, DIE CAST CORE WITH A HEAVY GAGE DIAL AND HANDLE MADE OF 3/32 INCH THICK ZINC PLATED STEEL, AND A 3/4 INCH HEXAGON LOCKING NUT. PROVIDE CENTER HOLE TO SUIT DAMPER OPERATING ROD SIZE. PROVIDE ELEVATED PLATFORM FOR INSULATED DUCT MOUNTING.

DRAWINGS BEFORE THE HVAC SUBCONTRACTORS START ANY ON SITE CONSTRUCTION WORK. TEST AND BALANCE REPORT TO BE PROVIDED FOR PROJECT MANAGER, ARCHITECT AND ENGINEERING.

7. THE TEST AND BALANCE SUBCONTRACTOR MUST INSPECT THE HVAC WORK ON A WEEKLY BASIS AS IT PROCEEDS AND REPORT ANY DEFICIENCIES AND SIGN OFF ON THE WORK TO DATE. THIS INCLUDES THE CONTROL SYSTEM.

8. THE TEST AND BALANCE CONTRACTOR SHALL WITNESS ALL DUCT PRESSURE TESTING AND VERIFY THE REQUIREMENTS ARE MET FOR CONSTRUCTION; SEALING AND LEAKAGE.

9. THIRTY (30) DAYS BEFORE STARTING THE TEST AND BALANCE WORK, THE T & B SUBCONTRACTOR MUST INSPECT THE HVAC SYSTEM AND REPORT TO THE A/E THE CONDITION OF THE SYSTEM AND EQUIPMENT.

10. TEST AND BALANCE CONTRACTOR SHALL ATTEND ALL FINAL AHJ INSPECTIONS.

11. CORRECTIVE WORK REQUIRED FOR SYSTEMS BALANCING, IF DETECTED DURING BALANCING WORK, SHALL BE REPORTED IN WRITING TO THE A/E WITH RECOMMENDED CORRECTIVE ACTION. 12. THE TEST AND BALANCE CONTRACTOR SHALL SCHEDULE HIS WORK SO AS TO COMPLETE IT AND PROVIDE A TYPED REPORT THAT WILL MEET AHJ REQUIREMENTS, TO THE OWNER 48 HOURS PRIOR TO THE AHJ INSPECTION.

PRESSURE, 1 INCH TEST PRESSURE.

J. VARIABLE REFRIGERANT FLOW SYSTEMS 1. DESCRIPTION: THE SYSTEM SHALL CONSIST OF A SINGLE OR MULTIPLE EVAPORATOR(S), THE

MANUFACTURER RECOMMENDED PIPE JOINING METHODS AND HEADERS, A TWO-PIPE REFRIGERANTPIPING SYSTEM, AND A SINGLE OR MULTIPLE AIR COOLED CONDENSING UNIT(S). THE CONDENSING UNITSHALL INCLUDE VARIABLE SPEED INVERTER DRIVEN COMPRESSORS USING R-410A REFRIGERANT. EACHINDOOR FAN COIL UNIT SHALL BE CAPABLE OF OPERATING INDEPENDENTLY WITH INDIVIDUALTEMPERATURE CONTROL. SYSTEMS SHALL BE CAPABLE OF UP TO 540 FEET (640 FEET EQUIVALENT) OFLINEAR PIPING BETWEEN THE CONDENSING UNIT AND FURTHEST LOCATED INDOOR UNIT. SYSTEMSSHALL BE CAPABLE OF UP TO 3,280 FEET TOTAL "ONE-WAY" PIPING IN THE PIPING NETWORK. SYSTEMSSHALL HAVE A VERTICAL (HEIGHT) SEPARATION OF UP TO 295 FEET BETWEEN THE CONDENSING UNITAND THE INDOOR UNITS. SYSTEMS SHALL BE CAPABLE OF UP TO 295 FEET FROM THE FIRST BRANCHPOINT. THE CONDENSING UNIT SHALL HAVE THE ABILITY TO CONNECT AN INDOOR UNIT EVAPORATORCAPACITY OF UP TO 200 PERCENT OF THE CONDENSING UNIT CAPACITY. SYSTEMS SHALL BE CAPABLEOF 49 FEET BETWEEN INDOOR UNITS. T STYLE PIPING JOINTS ARE NOT ACCEPTABLE.

2. DUCTLESS FAN COIL UNIT: EVAPORATOR OR SUPPLY FANS SHALL BE DOUBLE-WIDTH, DOUBLE INLET,FORWARD CURVED, BACKWARD INCLINED, OR AIRFOIL BLADE, CENTRIFUGAL DWDI TYPE. FURNISHCASING CONSTRUCTED OF HEAVY GAGE IMPACT RESISTANT PLASTIC WITH INTEGRAL INLET ANDDISCHARGE GRILLES. INTERIOR OF CASING SHALL BE LINED WITH POLYSTYRENE INSULATION. FRONTOF ENCLOSURE SHALL BE REMOVABLE FOR ACCESS TO INTEGRAL COMPONENTS. FILTER SHALL BEACCESSED THROUGH AN INDIVIDUAL ACCESS DOOR LOCATED IN THE CABINET FRONT. EVAPORATORFAN SCROLL SHALL CONSIST OF MULTIPLE FANS OR A SINGLE FAN WHEEL EXTENDING THE FULL WIDTHOF THE CABINET. FURNISH WITH EVAPORATOR COIL AND INSULATED DRAIN PAN.

3. EVAPORATOR COIL: PROVIDE COPPER TUBES OF 3/8 INCH MINIMUM DIAMETER WITH ALUMINUM FINSTHAT ARE MECHANICALLY BONDED OR SOLDERED TO THE TUBES. CASING SHALL BE GALVANIZED STEELOR ALUMINUM. CONTACT OF DISSIMILAR METALS SHALL BE AVOIDED. COILS SHALL BE TESTED INACCORDANCE WITH ANSI/ASHRAE 15 & 34 AT THE FACTORY AND BE SUITABLE FOR THE WORKINGPRESSURE OF THE INSTALLED SYSTEM. EVAPORATOR COIL SHALL BE DEHYDRATED AND SEALED AFTERTESTING AND PRIOR TO EVALUATION AND CHARGING. REFRIGERANT FLOW SYSTEM CONTROL DEVICESSHALL BE AN ADJUSTABLE SUPERHEAT THERMOSTATIC EXPANSION VALVE.

4. UNIT/SYSTEM CONTROLS: PROVIDE A SYSTEM MASTER CONTROL PANEL FOR INDOOR MOUNTING,CONSISTING OF A PROGRAMMABLE LOGIC CONTROLLER AND LCD TOUCH-SCREEN DISPLAY HOUSED ONAN IMPACT RESISTANT PLASTIC ENCLOSURE. MASTER CONTROLLER SHALL PROVIDE 24 HOUR/DAY, 7DAY/WEEK PROGRAMMING CAPABILITY FOR EACH INDOOR UNIT AND THE RELATED OUTDOOR UNIT(S),WITH MULTIPLE EVENT ACTION EACH DAY AND AUTOMATIC HEATING/COOLING CHANGEOVER BASED ONINDOOR UNIT REQUIREMENTS. INCLUDE TERMINAL BLOCKS FOR CONTROL AND POWER WIRING.FURNISH ONE LCD TOUCH-SCREEN CONTROLLER FOR EACH PIPED GROUP OF INDOOR UNIT(S) ANDOUTDOOR UNIT(S). PROVIDE A REMOTE TEMPERATURE SENSOR FOR EACH INDOOR UNIT LOCATION,INSTALLED IN AN IMPACT RESISTANT PLASTIC ENCLOSURE LOCATED WITHIN THE SPACE SERVED.

5. AIR-COOLED HEAT PUMP CONDENSING UNIT: RATE IN ACCORDANCE WITH AHRI 460 AND CONFORM TOTHE REQUIREMENTS OF UL 1995. UNIT SHALL BE FACTORY FABRICATED, TESTED, PACKAGED, ANDSELF-CONTAINED. UNIT SHALL BE COMPLETE WITH CASING, COMPRESSOR, PROPELLER FANS, HEATREJECTION COILS, CONNECTING PIPING, CONTACTORS AND WIRING, AND ALL NECESSARYAPPURTENANCES. CONDENSER OR OUTDOOR FANS SHALL BE PROPELLER TYPE.REFRIGERANT-CONTAINING COMPONENTS SHALL COMPLY WITH ANSI/ASHRAE 15 & 34 AND BE FACTORYTESTED, CLEANED, DEHYDRATED, CHARGED, AND SEALED. REFRIGERANT CHARGING VALVES ANDCONNECTIONS, AND PUMP DOWN VALVES SHALL BE PROVIDED. FILTER-DRIER SHALL BE PROVIDED INLIQUID LINE AND BE REVERSIBLE-FLOW TYPE. REFRIGERANT FLOW SYSTEM CONTROL DEVICES SHALLBE A SOLENOID CONTROLLED, LEAK-TIGHT, FOUR-WAY REFRIGERANT FLOW REVERSING VALVE. TOENSURE THE LIQUID REFRIGERANT DOES NOT FLASH WHEN SUPPLYING TO THE CONNECTED INDOORUNITS, THE CIRCUIT SHALL BE PROVIDED WITH A SUB-COOLING FEATURE. OIL RECOVERY CYCLE SHALLBE AUTOMATIC OCCURRING 2 HOURS AFTER START OF OPERATION AND THEN EVERY 8 HOURS OFOPERATION. EACH SYSTEM SHALL MAINTAIN CONTINUOUS HEATING DURING OIL RETURN OPERATION.REVERSE CYCLE (COOLING MODE) OIL RETURN DURING HEATING OPERATION SHALL NOT BE PERMITTEDDUE TO THE POTENTIAL REDUCTION IN SPACE TEMPERATURE..

6. CONDENSING COIL: PROVIDE ALUMINUM TUBES OF 3/8 INCH MINIMUM DIAMETER WITH ALUMINUM FINSTHAT ARE MECHANICALLY BONDED OR SOLDERED TO THE TUBES. CASING SHALL BE GALVANIZED STEELOR ALUMINUM. CONTACT OF DISSIMILAR METALS SHALL BE AVOIDED. COILS SHALL BE TESTED INACCORDANCE WITH ANSI/ASHRAE 15 & 34 AT THE FACTORY AND BE SUITABLE FOR THE WORKINGPRESSURE OF THE INSTALLED SYSTEM. EACH COIL SHALL BE DEHYDRATED AND SEALED AFTERTESTING AND PRIOR TO EVALUATION AND CHARGING. EACH UNIT SHALL BE PROVIDED WITH A FACTORYOPERATING CHARGE OF REFRIGERANT.

7. COMPRESSOR: PROVIDE SINGLE OR MULTIPLE COMPRESSOR(S). EACH COMPRESSOR SHALL BE DIRECTDRIVE, DIGITAL HERMETIC SCROLL TYPE, EQUIPPED WITH A VARIABLE SPEED DRIVE CONTROLLER,CAPABLE OF CHANGING THE SPEED TO FOLLOW THE VARIATIONS IN TOTAL COOLING AND HEATING LOADAS DETERMINED BY SUCTION GAS PRESSURE OF THE CONNECTED EVAPORATOR COILS, AS MEASUREDIN THE CONDENSING UNIT. IN ADDITION, THE CONTROL SYSTEM SHALL INTERROGATE EACHEVAPORATOR AND THE CONDENSER TEMPERATURES IN ORDER THAT THE HIGH/LOW PRESSURES AREDETECTED EVERY 20 SECONDS. WITH EACH READING, THE COMPRESSOR CAPACITY SHALL BECONTROLLED TO MEET THE TARGET VALUE. EACH COMPRESSOR SHALL BE CAPABLE OF A CAPACITYRANGE BETWEEN 6 PERCENT AND 100 PERCENT. EACH COMPRESSOR SHALL BE PROVIDED WITHVIBRATION ISOLATORS, CRANKCASE HEATER, THERMAL OVERLOADS, HIGH AND LOW PRESSURE SAFETYCUTOFFS AND PROTECTION AGAINST SHORT CYCLING.

8. AIR-COOLED HEAT PUMP CONDENSING UNIT CONTROLS: UNIT MOUNTED CONTROL PANELS ORENCLOSURES SHALL BE CONSTRUCTED IN ACCORDANCE WITH APPLICABLE REQUIREMENTS OF NFPA 70AND HOUSED IN NEMA ICS 6, CLASS 1A OR 3A ENCLOSURES. CONTROLS SHALL INCLUDE CONTROLTRANSFORMER, FAN MOTOR STARTERS, TIME DELAY START-UP, OVERLOAD PROTECTIVE DEVICES,INTERFACE WITH LOCAL AND REMOTE COMPONENTS, AND INTER-COMPONENT WIRING TO TERMINALBLOCK POINTS. UNIT SHALL BE INTERNALLY PREWIRED WITH A 24 VOLT CONTROL CIRCUIT POWERED BYAN INTERNAL TRANSFORMER. INCLUDE LOW AMBIENT CONTROL FOR STABLE SYSTEM OPERATIONDOWN TO 32 DEGREE F AMBIENT.

9. REFRIGERANT PIPING: COMPLY WITH ASME B31.5, “REFRIGERATION PIPING” AND ASHRAE 15, “SAFE CODEFOR MECHANICAL REFRIGERATION”. PROVIDE HARD DRAWN OR SOFT COPPER TUBE; ASTM B 280, TYPEACR. COPPER FITTINGS; ASME B16.22, WROUGHT COPPER, STREAMLINE PATTERN. BRAZER FILLINGMATERIALS; AWS A5.8, CLASSIFICATION BAG-1, SILVER.

10. CONDENSATE DRAIN PIPING: PVC; SCHEDULE 40. PVC FITTINGS; ASTM D 2466, SOCKET TYPE. SOLVENTWELDED JOINTS.

11. PIPING INSULATION: ¾ INCH THICK FLEXIBLE CELLULAR FOAM; ARMSTRONG, RUBATEX, OR APPROVEDEQUAL.

12. PIPING INSTALLATION: INSTALL REFRIGERANT PIPING OF LINE SIZES RECOMMENDED BY EQUIPMENTMANUFACTURER IN ACCORDANCE WITH ASHRAE 15. INSTALL CONDENSATE DRAIN PIPING; MINIMUM ¾INCH SIZE, WITH A MINIMUM OF 1/8 INCH PER FOOT DROP IN ELEVATION IN THE DIRECTION OF FLOW.INSTALL PIPING IN SHORT AND DIRECT ARRANGEMENT, WITH THE MINIMUM NUMBER OF JOINTS, ELBOWSAND FITTINGS. ARRANGEMENT OF PIPING SHALL PERMIT ACCESS TO COILS, FILTER SECTIONS, ANDCONDENSING UNIT COMPONENTS. SUPPORT ALL REFRIGERANT PIPING TO BUILDING STRUCTURE WITHCOPPER CLAD CLIPS. SUPPORT CONDENSATE DRAIN PIPING WITH GALVANIZED STEEL STRAP HANGERS.INSTALL VALVES AND SPECIALTIES IN ACCESSIBLE LOCATIONS TO ALLOW FOR SERVICE ANDINSPECTION. INSTALL PIPING WITH ADEQUATE CLEARANCE BETWEEN PIPING AND ADJACENT SURFACES. FOR CONDENSING UNITS IMMEDIATELY ADJACENT TO EXTERIOR WALLS, PROVIDE SCHEDULE 40 PVCSLEEVE THROUGH EXTERIOR WALL FOR REFRIGERANT PIPING EGRESS. SEAL SLEEVE ANNULAR SPACEWITH EXPANDING FOAM SEALANT. ALL SLEEVE AND CONDUIT PENETRATIONS THROUGH EXTERIORWALLS SHALL BE GROUTED IN PLACE; TROWELED EVEN WITH SURFACE OF MASONRY. INSULATE ALLREFRIGERANT SUCTION LINES, REFRIGERANT HOT GAS LINES, AND CONDENSATE DRAIN LINES. INSTALLINSULATION WITH CONTACT ADHESIVE; SIMILAR TO ARMSTRONG 520, ON ALL BUTT AND LONGITUDINALJOINTS. EXTEND INSULATION THROUGH SLEEVES AND WALL PENETRATIONS WITHOUT JOINTS. TESTPIPING FOR LEAKS PRIOR TO INSULATION. PURGE PIPING WITH NITROGEN DURING SOLDERING ANDBRAZING. PROVIDE BRAZED JOINTS; FLARE JOINTS ARE NOT ACCEPTABLE. PROVIDE PIPE SIZES WHICHCOMPLY WITH MANUFACTURER'S EQUIPMENT WRITTEN INSTRUCTIONS AND RECOMMENDATIONS FORDISTANCES INDICATED. PROVIDE FABRICATED GALVANIZED STEEL OR ALUMINUM PROTECTIVE COVEROVER REFRIGERANT PIPING INSTALLED EXTERIOR TO STRUCTURE.

F. CONTROL WIRING:1. PROVIDE ELECTRICAL WIRING FOR THE DDC SYSTEM, INCLUDING WIRING TO

TRANSFORMER PRIMARIES. WIRING SHALL COMPLY WITH NEC. WIRING FOR24 V CIRCUITS SHALL BE INSULATED COPPER, MINIMUM 18 AWG MINIMUM ANDRATED FOR 300 VAC SERVICE. WIRING FOR 120 V CIRCUITS SHALL BEINSULATED COPPER, MINIMUM 14 AWG MINIMUM AND RATED FOR 600 VACSERVICE.

No 77673

STATE OF

RK S.ERED

PR

OF

NSSOI

ELA ENGIN

EER

LICENSE

F LO RIDA

EED

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

11:41

:3 1 A

M

MH002

MECHANICALSPECIFICATIONS

VLM

DSR

1

1

1


1 ADDENDUM 1 10-23-15

TT T

TTT

T

T

T

T

T

34

1

1

1

12

2

3

4

5

5

1

14

5

3

1 1

3

4

4

35

4

4

3

3

3

12x6(E) 12x6(E)

12x1

0(E)

12x6(E)

12x6(E)

16x1

0(E)

12x6(E) 12x6(E)

18x1

8(E) 12

x10(

E)

12x6(E) 12x6(E)

12x6(E) 12x6(E)

16x1

0(E)

12x6(E)12x6(E)

12x1

0(E)

18x1

2(E)

24x1

4(E)

18x1

4(E)10

x8(E

)

12x6(E) 12x6(E)

12x1

0(E)

16x1

0(E)12x6(E)

12x1

0(E)

12x6(E)

12x6(E) 12x6(E) 12x6(E)

12x1

0(E)

16x1

0(E)

12x1

0(E)

12x6(E)12x6(E)

10ø(E)10ø(E)

12x6(E) 12x6(E)

14x6

(E)1

4x6(

E)

12x6(E)

12x6(E)

12x6(E)

12x6(E)

12x12(E)8x

12(E

)

24x12(E)

26x16(E)16

x12(

E)

24x1

2(E)

26x1

6(E)

12x6

(E)

12x1

0(E)

18x1

0(E)

12x6

(E)

12x10(E)

12x1

0(E)

12x6(E)

12x6(E)

20x2

6(E)

36x1

8(E)

12x10(E) 12x10(E)

AHU(E)B1.1

AHU(E)B1.4

960FP2-3(E)

960FP2-1(E)

1440FP2-2(E)

480FP2-4(E)

640FP2-5(E)

1440FP4-6(E)

1440FP4-7(E)

450FP1-7(E)

450FP1-8(E)

1500FP1-9(E)

1500FP1-10(E)

6

77

77

77

6

CD-A(E)

TG-A(E)

TYP. 6

TYP. 3

CD-A(E)TG-A(E)

TYP. 7

TG-A(E) CD-A(E) TYP. 7

CD-A(E)

TG-A(E)

TYP. 4TYP. 2

CD-A(E)TYP. 6

TG-A(E)TYP. 2

TG-A(E)TYP. 2

CD-A(E)TYP. 6

CD-A(E)TYP. 12

TG-A(E)TYP. 4

No 77673

STATE OF

RK S.ERED

PR

OF

NSSOI

ELA ENGIN

EER

LICENSE

F LO RIDA

EED

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

11:36

:1 3 A

M

B1-MD101

BUILDING 1FLOOR PLAN -HVAC - DEMO

VLM

DSR

1/8" = 1'-0"1 BUILDING 1 FLOOR PLAN - HVAC - DEMO

A DUCTWORK AND EQUIPMENT INDICATED ARE EXISTING.B CONTRACTOR SHALL FIELD VERIFY ALL EXISTING

CONDITIONS PRIOR TO PROCEEDING WITH DEMOLITION. NOTIFY OWNER OF ANY VARIATIONS IN EXISTING CONDITIONSTHAT MAY AFFECT NEW WORK. RECORD DISCREPANCIES ONRECORD DRAWINGS.

C REFER TO ARCHITECTURAL PHASING PLANS FOR ADDITONAL INFORMATION REGARDING CONSTRUCTION AND LIMITS OF WORK SPACE. COORDINATE SEQUENCE OFCONSTRUCTION, TEMPORARY PARTITIONS, PHASING NOTES,TEMPORARY CAPS, TEMPORARY SERVICES, DUCTWORKDEMOLITION WITH AREAS TO BE MAINTAINED IN OPERATIONDURING THE CONSTRUCTION PERIOD.

D PERFORM WORK THAT MAY INTERRUPT ANY SERVICE TOADJACENT AREAS AT TIMES THAT WILL NOT DISTURBFACILITY OPERATION.

E OBTAIN APPROVAL FROM OWNER PRIOR TO SHUTDOWN OFAIR SYSTEMS FOR EQUIPMENT AND DUCTWORK REMOVAL.NOTIFICATION SHALL BE PROVIDED A MINIMUM OF 7 DAYSPRIOR TO INTENDED ACTION AND SHALL I INCLUDE A LISTOF SERVICES AFFECTED, SCHEDULE OF WORK, ANDPLANNED START DATE.

F COORDINATE DUCT REMOVAL WITH CAPPINGREQUIREMENTS INDICATED ON DUCT INSTALLATIONDRAWINGS. CONDUCT REMOVAL/CAPPING SEQUENTIALLYTO MINIMIZE SYSTEM DOWNTIME.

G PROTECT EXISTING AIR VALVES.

1 EXISTING THERMOSTAT TO REMAIN.

2 EXISTING THERMOSTAT TO BE RELOCATED.

3 REMOVE SUPPLY DIFFUSERS AND ASSOCIATED DUCTWORKTO POINTS INDICATED. TYPICAL.

4 REMOVE TRANSFER AIR GRILLES. PREPARE EXISTINGDUCTWORK FOR NEW CONNECTION. REPAIR EXISTINGINSULATION AS REQUIRED. TYPICAL.

5 EXISTING DUCTWORK TO REMAIN. TYPICAL.

6 EXISTING AIR HANDLING UNIT TO REMAIN. MEASURE ANDRECORD EXISTING AIRFLOWS AND TURN OVER TOFACILITIES AND ARCHITECT PRIOR TO DEMOLITION.

7 PROVIDE TRAVERSE READING AT POINT INDICATED.RECORD DATA AND TURN OVER TO FACILITIES ANDARCHITECT PRIOR TO DEMOLITION.

1

1

1

1

1 1

1

1

1

1

1 1

1

1

1

11


1 ADDENDUM 1 10-23-15

TTT

T

T

T

T

T

T

T

1

1

2

2

3

2

3

2

3

3

CD-A225 CD-A

225

TG-A

TG-A

TG-A

CD-A250

CD-A250

TG-A

TG-A

TG-ACD-A240 TYP. 6

TYP. 6

TYP. 2 TYP. 2

TYP. 6

TYP. 6

TG-A

TG-A

TG-A

TG-A

TG-A

TG-A

TG-ACD-A160

CD-A240

CD-A240TYP. 2

TYP. 4

CD-A240TYP. 4

TYP. 3

18x1

8(E)

12x1

0(E)

12x6(E)

12x1

0(E)

12x1

0(E)

12x6(E)12x6(E)

12x1

0(E)

12x6(E) 12x6(E)12x6(E)12x6(E) 16x1

0(E)

12x6(E)

18x1

2(E)

12x6(E)

18x1

4(E)

10ø(E)

10ø(E)

10x8

(E)

12x10(E)

10x8

(E)

24x1

4(E)

12x6(E)

12x1

0(E)

12x6(E) 16x1

0(E)

12x1

0(E)

12x6(E) 12x6(E)

12x1

0(E)

16x1

0(E)

12x6(E)

12x6(E)

12x1

0(E)

12x6(E)

12x6(E)

12x6(E)

12x12(E)

8x12

(E)

26x16(E)

12x6(E)14

x6(E

)

12x6(E)

12x6(E)

24x12(E)

16x1

2(E)

12x6

(E) 12x10(E)

12x6

(E)

12x6

(E)

12x10(E)

12x6(E)

12x1

0(E)

12x6(E)

12x6

(E)

18x1

0(E)

12x10(E)12x6

(E)

12x6

(E)

12x1

0(E)

12x10(E)

12x6

(E)

12x6

(E)

20x16(E)

10ø(E)

12x10(E)

26x1

6(E)

36x1

8(E)

CD-A220 TYP. 4

2

2

2

22

2

AHU(E)B1.1

AHU(E)B1.4

960FP2-3(E)

960FP2-1(E)

1440FP2-2(E)

480FP2-4(E)

640FP2-5(E)

1440FP4-6(E)

1440FP4-7(E)

1500FP1-9(E)

1500FP1-10(E)

450FP1-7(E) 450

FP1-8(E)

CD-A240

CD-A80

10x610x6

TG-A

4

5

CLASSROOM111

CLASSROOM139B

CLASSROOM139A

COMM ROOM136

CLASSROOM150

CLASSROOM149

OFFICE148

CLASSROOM135

CD-A240 TYP. 3

6

6

66

66

77

7 7

7 7

8

8

6

No 77673

STATE OF

RK S.ERED

PR

OF

NSSOI

ELA ENGIN

EER

LICENSE

F LO RIDA

EED

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

11:41

:2 3 A

M

B1-MH101

BUILDING 1FLOOR PLAN -HVAC

VLM

DSR

1/8" = 1'-0"1 BUILDING 1 FLOOR PLAN - HVAC

1 RELOCATED THERMOSTAT.

2 CONNECT TO EXISTING DUCTWORK AND SEAL AIR TIGHT.EXTEND DUCTWORK TO CEILING DIFFUSER. REPAIR DUCTINSULATION. TYPICAL.

3 THERMOSTAT TO CONTROL MULTIPLE AIR VALVES/FANPOWERED BOXES.

4 MAINTAIN CLEARANCES FOR MAINTENANCE OF FP-2-1(E).

5 TRANSFER AIR DUCT.

6 EXISTING THERMOSTAT.

7 PROVIDE AIR QUANTITY TRAVERSE MEASUREMENT INDUCTWORK FOLLOWING RENOVATION.

8 REBALANCE AHU. REFER TO AHU BALANCING SCHEDULE FOR AIR QUANTITIES.

A DUCT SIZES NOTED INDICATE MINIMUM INSIDE DIMENSIONS.B MINIMUM DUCT SIZE IS 10X6 EXCEPT WHERE SPECIFICALLY

INDICATED OTHERWISE.C DUCTWORK LOCATIONS SHOWN ARE SCHEMATIC. REFER TO

SPECIFICATIONS FOR SHOP DRAWING AND COORDINATION DRAWING REQUIREMENTS. DO NOT PROCEED WITHINSTALLATION OF DUCTWORK UNTIL APPROVED SHOPDRAWINGS ARE AVAILABLE AT THE SITE.

D COORDINATE CEILING DIFFUSER, REGISTER AND GRILLE LOCATIONS WITH REFLECTED CEILING PLANS.

E MOUNT ROOM THERMOSTATS/SENSORS AT 48" AFF.F PROVIDE ACCESS DOORS IN DUCTWORK FOR VISUAL

INSPECTION OF ALL CONTROL DAMPERS, TEMPERATURE CONTROL DEVICES, SMOKE DETECTORS, FIRE DAMPERS AND SMOKE DAMPERS.

G PROVIDE ACCESS PANELS IN NON-ACCESSIBLE GENERAL CONSTRUCTION SUBSTRATES FOR MAINTENANCE AND ADJUSTMENT OF ALL CONCEALED DAMPERS, AIR CONTROL DEVICES, EQUIPMENT AND DUCTWORK ACCESS DOORS. WOOD, GYPSUM DRYWALL AND CONCEALED SPLINE TILE CEILINGS ARE CONSIDERED NON-ACCESSIBLE.

H REFER TO TYPICAL DETAIL SHEETS FOR GENERAL DUCTWORK CONSTRUCTION, INSTALLATION, ASSEMBLY DETAILS, AND CONNECTIONS TO AIR VALVES AND AIR TERMINALS.

I REFER TO ARCHITECTURAL PHASING PLANS FOR ADDITIONAL INFORMATION REGARDING NEW CONSTRUCTION AND LIMITS OF WORK SPACE. COORDINATE SEQUENCE OF NEW CONSTRUCTION, TEMPORARY PARTITIONS, PHASING NOTES, TEMPORARY CAPS, TEMPORARY SERVICES, DUCTWORK AND PIPING INSTALLATION WITH AREAS TO BE MAINTAINED IN OPERATION DURING THE CONSTRUCTION PERIOD.

J PERFORM WORK THAT MAY INTERRUPT ANY SERVICE TO ADJACENT AREAS AT TIMES THAT WILL NOT DISRUPT FACILITY OPERATION.

K OBTAIN APPROVAL FROM OWNER PRIOR TO SHUTDOWN OF AIR SYSTEMS FOR EQUIPMENT AND DUCTWORK INSTALLATION. NOTIFICATION SHALL INCLUDE LIST OF SERVICES AFFECTED, SCHEDULE OF WORK, AND PLANNED START DATE.

L BALANCE DIFFUSERS, REGISTERS, AND GRILLES FOR AIR QUANTITIES INDICATED BY BOLD TYPE.

M OBSERVE PRESSURIZATION OF ADJACENT OCCUPIED SPACES ON A DAILY BASIS TO MAINTAIN THE AREA OF RENOVATION AT A NEGATIVE PRESSURE IN RELATION TO OCCUPIED AREAS. AIR QUANTITIES SHALL BE SET AND MEASURED BY A CERTIFIED TEST AND BALANCE AGENCY AT START OF RENOVATION.

N PROTECT EXISTING AIR VALVES AND RELOCATED EQUIPMENT.

1

1

1

1

1 1

1

1

1

1

1

1 1

1

1

1

1


1 ADDENDUM 1 10-23-15

S

24x12(E)

(12) CD-A130 EA.

(5)CD-A(E)180 EA.

CD-A(E)200

(6)CD-A(E)210 EA.(5) CD-A (E)

160 EA.

CD-A(E)180

(5) CD-A(E)220 EA.

CD-A(E)230

(4) CD-A(E)220 EA. (2)CD-A(E)

245 EA.

CD-A(E)230

(5)CD-A(E)220 EA.

24x12

CD-A(E)110

CD-A(E)180

24x14(E)

CH(E)

CH

WR

(E)C

HW

S(E)C

HW

S(E)C

HW

R(E)

CH

WS(E)

CH

WR

(E)

8x6(E)

12x1

2(E)

10x1

0(E)

18x1

2(E)

22x1

2(E)

8x8(E)

10x8

(E)

8x8(E)

12x1

2(E)

8x6(E)10x8(E)

18x1

2(E)

8x6(

E)

6x6(E)

8x8(E)

12x8

(E)

8x8(E)

8x8(E)

6x6(E)

8x6(E)

8x6(E)

12x1

2(E)

10x8

(E)

6x6(

E) 14x1

2(E)

CD-A(E)70

10x8

(E)

8x8(

E)

8x8(E)

20x12(E) 14x12(E)

14x12(E)

16x12(E)22x12(E)

18x1

2(E)

14x1

2(E)

CD-A(E)50

CD-A(E)50

22x16(E)

36x18(E)

12x1

2(E)

14x12

10x1

2(E)

8x8(

E)

8x6(E)

F

S

32x8(E)

8x6(E)

8x6(E)

8x6(E)

8x6(E)

8x6(E)

8x6(E)

8x6(E)

8x8(E)

8x6(E)

8x6(E)8x6(E)

8x6(E)

8x6(E)

8x6(E)

6x6(E)

8x8(E)

8x8(E)

8x8(E)

8x8(E)

12x1

2(E)

12x1

2(E)

8x6(E)

8x6(

E)

10x1

0(E)

8x8(

E)8x

8(E)

8x8(

E)8x

8(E)

8x8(

E)8x

8(E)

8x8(

E)8x

8(E)

8x8(

E)

8x8(

E)

8x8(

E)

10x10(E)

10x10(E)

10x10(E)

8x8(

E)

8x8(

E)

8x8(

E) 8x8(

E)

8x10

(E)

8x10

(E)

32x8(E)

32x8(E)

18x12(E)

18x12(E)

CD-A(E)190

T

T

T

T

TTT

T

5

1

1

1

5

7

6

6

7

7

7

7

7

2

22

2

3

3

3

No 77673

STATE OF

RK S.ERED

PR

OF

NSSOI

ELA ENGIN

EER

LICENSE

F LO RIDA

EED

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

11:41

:2 6 A

M

B2-MD101

BUILDING 2FLOOR PLAN -HVAC - DEMO

VLM

DSR

1/8" = 1'-0"1 BUILDING 2 FLOOR PLAN - HVAC - DEMO

A DUCTWORK AND EQUIPMENT INDICATED ARE EXISTING.B CONTRACTOR SHALL FIELD VERIFY ALL EXISTING

CONDITIONS PRIOR TO PROCEEDING WITH DEMOLITION. NOTIFY OWNER OF ANY VARIATIONS IN EXISTINGCONDITIONSTHAT MAY AFFECT NEW WORK. RECORD DISCREPANCIES ONRECORD DRAWINGS.

C REFER TO ARCHITECTURAL PHASING PLANS FOR ADDITONAL INFORMATION REGARDING CONSTRUCTION AND LIMITS OF WORK SPACE. COORDINATE SEQUENCE OFCONSTRUCTION, TEMPORARY PARTITIONS, PHASING NOTES,TEMPORARY CAPS, TEMPORARY SERVICES, DUCTWORKDEMOLITION WITH AREAS TO BE MAINTAINED IN OPERATIONDURING THE CONSTRUCTION PERIOD.

D PERFORM WORK THAT MAY INTERRUPT ANY SERVICE TOADJACENT AREAS AT TIMES THAT WILL NOT DISTURBFACILITY OPERATION.

E OBTAIN APPROVAL FROM OWNER PRIOR TO SHUTDOWN OFAIR SYSTEMS FOR EQUIPMENT AND DUCTWORK REMOVAL.NOTIFICATION SHALL BE PROVIDED A MINIMUM OF 7 DAYSPRIOR TO INTENDED ACTION AND SHALL I INCLUDE A LISTOF SERVICES AFFECTED, SCHEDULE OF WORK, ANDPLANNED START DATE.

F COORDINATE DUCT REMOVAL WITH CAPPINGREQUIREMENTS INDICATED ON DUCT INSTALLATIONDRAWINGS. CONDUCT REMOVAL/CAPPING SEQUENTIALLYTO MINIMIZE SYSTEM DOWNTIME.

G PROTECT EXISTING AIR VALVES.

1050VAV 10 (E)

1310VAV 11 (E)

1260VAV 12 (E)

1560VAV 13 (E)

520VAV 16 (E)

1520VAV 3 (E)

1370VAV 4 (E)

1330VAV 5 (E)

B2.2AHU(E)

B2.1AHU(E)

1 EXISTING THERMOSTAT TO REMAIN.

2 EXISTING THERMOSTAT TO BE RELOCATED.

3 REMOVE SUPPLY DIFFUSERS AND ASSOCIATED DUCTWORKTO POINTS INDICATED. TYPICAL.

4 REMOVE TRANSFER AIR GRILLES. PREPARE EXISTINGDUCTWORK FOR NEW CONNECTION. REPAIR EXISTINGINSULATION AS REQUIRED. TYPICAL.

5 EXISTING DUCTWORK TO REMAIN. TYPICAL.

6 EXISTING AIR HANDLING UNIT TO REMAIN. MEASURE ANDRECORD EXISTING AIRFLOWS AND TURN OVER TOFACILITIES AND ARCHITECT PRIOR TO DEMOLITION.

7 PROVIDE TRAVERSE READING AT POINT INDICATED.RECORD DATA AND TURN OVER TO FACILITIES ANDARCHITECT PRIOR TO DEMOLITION.

1

1

1

1

1 1

1

1

1

1

1

1

1

1

1

1

1

1


1 ADDENDUM 1 10-23-15

S

CH

WR

(E)C

HW

S(E)C

HW

S(E)C

HW

R(E)

CH

WS(E)

CH

WR

(E)

8x6(E)

12x1

2(E)

10x1

0(E)

18x1

2(E)

22x1

2(E)

8x8(E)

10x8

(E)

8x8(E)

12x1

2(E)

8x6(E)10x8(E)18

x12(

E)

8x6(

E)

6x6(E)

8x8(E)12

x8(E

)

8x8(E)

8x8(E)

6x6(E)

8x6(E)

8x6(E)

12x1

2(E)

10x8

(E)

6x6(

E) 14x1

2(E)

CD-A(E)70

10x8

(E)

8x8(

E)

8x8(E)

20x12(E) 14x12(E)

14x12(E)

16x12(E)22x12(E)

18x1

2(E)

14x1

2(E)

CD-A(E)50

CD-A(E)50

22x16(E)

36x18(E)

12x1

2(E)

14x12

10x1

2(E)

8x8(

E)

8x6(E)

F

S

32x8(E)

8x6(E)

8x6(E)

8x6(E)

8x6(E)

8x6(E)

8x6(E)

8x6(E)

8x8(E)

8x6(E)

8x6(E)8x6(E)

8x6(E)

8x6(E)

8x6(E)

6x6(E)

8x8(E)

8x8(E)

8x8(E)

8x8(E)

12x1

2(E)

12x1

2(E)

8x6(E)

8x6(

E)

10x1

0(E)

8x8(

E)8x

8(E)

8x8(

E)8x

8(E)

8x8(

E)8x

8(E)

8x8(

E)8x

8(E)

8x8(

E)

8x8(

E)

8x8(

E)

10x10(E)

10x10(E)

10x10(E)

8x8(

E)

8x8(

E)

8x8(

E) 8x8(

E)

8x10

(E)

8x10

(E)

32x8(E)

32x8(E)

18x12(E)

18x12(E)

CD-A(E)190

T

T

T

T

TTT

T

T T TT

COMPUTER LAB101

COMPUTER LAB102

COMPUTER LAB103

1 1 1 1

1

1

1

TG-A

TG-A

RR-A

TG-A TG-ATG-A

2

RR-A

RR-A

2

RR-A

CD-A245

CD-A220

TYP. 4

CD-A220 TYP. 5

CD-A230

CD-A230

CD-A220 TYP. 5

CD-A180

CD-A170

CD-A170

CD-A130 TYP. 12

CD-A180

TYP. 5

CD-A200

CD-A110

TYP. 6CD-A210

CD-A180

CD-A160

TYP. 5

TG-A

B2.1CU

FCUB2.4

FCUB2.3

FCUB2.2

FCUB2.1

3

3333 4

3

3

3

3

1" D1" D

CD-A245MULTI-PURPOSE

ROOM109B

OFFICE115

TUTORINGCENTER

116

OFFICE114

5

9

8

8

77

77

7

7

7

6

6

6

6

6

6

6

No 77673

STATE OF

RK S.ERED

PR

OF

NSSOI

ELA ENGIN

EER

LICENSE

F LO RIDA

EED

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

11:41

:2 8 A

M

B2-MH101

BUILDING 2FLOOR PLAN -HVAC

VLM

DSR

1/8" = 1'-0"1 BUILDING 2 FLOOR PLAN - HVAC

A DUCT SIZES NOTED INDICATE MINIMUM INSIDE DIMENSIONS.B MINIMUM DUCT SIZE IS 10X6 EXCEPT WHERE SPECIFICALLY

INDICATED OTHERWISE.C DUCTWORK LOCATIONS SHOWN ARE SCHEMATIC. REFER TO

SPECIFICATIONS FOR SHOP DRAWING AND COORDINATION DRAWING REQUIREMENTS. DO NOT PROCEED WITHINSTALLATION OF DUCTWORK UNTIL APPROVED SHOPDRAWINGS ARE AVAILABLE AT THE SITE.

D COORDINATE CEILING DIFFUSER, REGISTER AND GRILLE LOCATIONS WITH REFLECTED CEILING PLANS.

E MOUNT ROOM THERMOSTATS/SENSORS AT 48" AFF.F PROVIDE ACCESS DOORS IN DUCTWORK FOR VISUAL

INSPECTION OF ALL CONTROL DAMPERS, TEMPERATURE CONTROL DEVICES, SMOKE DETECTORS, FIRE DAMPERS ANDSMOKE DAMPERS.

G PROVIDE ACCESS PANELS IN NON-ACCESSIBLE GENERAL CONSTRUCTION SUBSTRATES FOR MAINTENANCE AND ADJUSTMENT OF ALL CONCEALED DAMPERS, AIR CONTROLDEVICES, EQUIPMENT AND DUCTWORK ACCESS DOORS. WOOD, GYPSUM DRYWALL AND CONCEALED SPLINE TILE CEILINGS ARE CONSIDERED NON-ACCESSIBLE.

H REFER TO TYPICAL DETAIL SHEETS FOR GENERAL DUCTWORKCONSTRUCTION, INSTALLATION, ASSEMBLY DETAILS, AND CONNECTIONS TO AIR VALVES AND AIR TERMINALS.

I REFER TO ARCHITECTURAL PHASING PLANS FOR ADDITIONALINFORMATION REGARDING NEW CONSTRUCTION AND LIMITSOF WORK SPACE. COORDINATE SEQUENCE OF NEW CONSTRUCTION, TEMPORARY PARTITIONS, PHASING NOTES,TEMPORARY CAPS, TEMPORARY SERVICES, DUCTWORK ANDPIPING INSTALLATION WITH AREAS TO BE MAINTAINED IN OPERATION DURING THE CONSTRUCTION PERIOD.

J PERFORM WORK THAT MAY INTERRUPT ANY SERVICE TO ADJACENT AREAS AT TIMES THAT WILL NOT DISRUPTFACILITY OPERATION.

K OBTAIN APPROVAL FROM OWNER PRIOR TO SHUTDOWN OFAIR SYSTEMS FOR EQUIPMENT AND DUCTWORK INSTALLATION.NOTIFICATION SHALL INCLUDE LIST OF SERVICES AFFECTED,SCHEDULE OF WORK, AND PLANNED START DATE.

L BALANCE DIFFUSERS, REGISTERS, AND GRILLES FOR AIR QUANTITIES INDICATED BY BOLD TYPE.

M OBSERVE PRESSURIZATION OF ADJACENT OCCUPIED SPACESON A DAILY BASIS TO MAINTAIN THE AREA OF RENOVATION AT ANEGATIVE PRESSURE IN RELATION TO OCCUPIED AREAS. AIRQUANTITIES SHALL BE SET AND MEASURED BY A CERTIFIEDTEST AND BALANCE AGENCY AT START OF RENOVATION.

N PROTECT EXISTING AIR VALVES AND RELOCATED EQUIPMENT.

1 PROVIDE NEW SUPPLY DIFFUSER. MODIFY EXISTINGDUCTWORK AS REQUIRED TO LOCATE DIFFUSER INTONEW CEILING GRID. TYP.

2 PROVIDE NEW RETURN DIFFUSER. MODIFY EXISTINGDUCTWORK AS REQUIRED TO LOCATE DIFFUSER INTONEW CEILING GRID. TYP.

3 PROVIDED UNDER ADD ALTERNATE 1 - MECHANICAL.

4 ROUTE 1" CONDENSATE DRAIN TO FLOOR DRAIN.

5 PIPE SLEEVES.

6 EXISTING THERMOSTAT.

7 PROVIDE AIR QUANTITY TRAVERSE MEASUREMENT INDUCTWORK FOLLOWING RENOVATION.

8 REBALANCE AHU. REFER TO AHU BALANCING SCHEDULE FOR AIR QUANTITIES.

9 CONDENSING UNIT. COORDINATE REFRIGERANT PIPE SIZESWITH MANUFACTURER OF APPROVED EQUIPMENTSELECTIONS.

1050VAV 10 (E)

1310VAV 11 (E)

1260VAV 12 (E)

1560VAV 13 (E)

1520VAV 3 (E)

1370VAV 4 (E)

1330VAV 5 (E)

B2.2AHU(E)

B2.1AHU(E)

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1


1 ADDENDUM 1 10-23-15

SECTION

CEILING TILE ANDSUSPENSION

BRANCH DUCTOR SUB-MAIN

BRANCH DUCT

FLEXIBLE DUCTCONNECTOR MAXFIVE FEET

SPIN-IN FITTING

2" THICK DUCT WRAPINSULATION (ENTIREDIFFUSER BACK)

CEILING DIFFUSEROR CEILINGREGISTER

NOTES:1.ALL SQUARE OR RECTANGULAR ELBOWS (NON-RADIUS TYPE) SHALL HAVE ONE OF THE TWO TYPES OF TURNING VANES SHOWN ABOVE.2.VANES SHALL BE CONSTRUCTED, SUPPORTED AND FASTENED AS RECOMMENDED BY SMACNA.3.ALL SQUARE OR RECTANGULAR ELBOWS SHOWN ON PLANS FOR EXHAUST OR RETURN DUCT MAY BE MADE RADIUS ELBOWS PROVIDED

SPACE PERMITS RADIUS INSTALLATION.4.ALL SQUARE OR RECTANGULAR ELBOWS SHOWN ON PLANS FOR SUPPLY DUCT MAY BE MADE RADIUS ELBOWS PROVIDED SPACE PERMITS

RADIUS INSTALLATION AND THERE IS NO OUTLET OR TAKE-OFF WITHIN 5D ON THE DOWNSTREAM SIDE OF THE ELBOW.

2-1/4" 2-1/4"

3-1/4

"

4-1/2" R2-1/4" R45°

1-1/8" 1-1/8"

1" R45° 2" R

USE FOR ELBOWS 36" ORWIDER AND ANY DEPTH

USE FOR ELBOWS UP TO36" IN WIDTH AND/OR DEPTH

LARGE DOUBLE VANE ELBOW SMALL SINGLE VANE ELBOW

WIDTH (W)

DEPTH (D)

TURNING VANES

4" MIN.(TYP)

3/2 D

FRONT VIEW MITERED ELBOW SMOOTH RADIUS ELBOW

SECTION

CEILING TILE ANDSUSPENSION

GALVANIZED STEELDUCTWORK WITH 1-1/2"THICK ACOUSTICALFIBROUS GLASSINSULATION LINER.

CEILING TRANSFERAIR GRILLE

90° ELBOW

22 X 22PLENUMRETURN

NOTES:1. PROVIDE WITH EQUIPMENT PRODUCT SUBMITTAL A REFRIGERANT PIPING DIAGRAM INDICATING PIPE SIZES, SCHEMATIC LAYOUT, VALVES, FITTINGS AND ACCESSORIES, WITH DIMENSIONED PIPING LENGTHS SPECIFIC TO EACH INSTALLATION. PIPE SIZES AND LOCATIONS OF OIL TRAPS, MOISTURE SITE GLASS, LIQUID LINE FILTER/DRYER SHALL CONFORM TO MANUFACTURER'S RECOMMENDATIONS PER PIPING ARRANGEMENT.2. CONDENSING UNIT TO BE SECURED TO CONCRETE PAD OR ROOF EQUIPMENT SUPPORTS ON EACH SIDE BY A MINIMUM OF THREE #14 SCREWS WITH GASKETED WASHERS TO MEET WIND RESISTANCE.

BUILDINGINTERIOR

EXTEND TOFLOOR DRAIN

CONDENSATEP-TRAP

DX COOLINGCOIL UNIT

BUILDINGEXTERIOR

STOP VALVE

RL

SLEEVETYP.

RS

REFRIGERANTLINE PIPING

AIR COOLEDCONDENSER

REINFORCED CONCRETEHOUSEKEEPING PAD

SCHRADERACCESS FITTINGTYP.

TS

PROVIDE INDIVIDUALTEMPERATURE SENSORFOR EACH AC UNITLOCATE IN SPACESERVED BY VRF MFR

SYSTEM FAULT STATUS.INTERLOCK TO NEAREST DDCCONTROLLER TO ENABLE ALARMANNUNCIATION AT DDCWORKSTATION COMPUTER.

INTERLOCK TO CONDENSINGUNIT

AC

AC

AC

CU

RSRL

RSRL

S

S

S

VRF HEAT PUMPCONDENSING UNIT

INTERLOCK TO OPEN UPON ACUNIT OPERATIONTYPICAL

LCD DISPLAY BY VRV SYSTEMMFR.

NOTE: VERIFY CONFIGURATION OF EACH VRVSYSTEM WITH PIPING FLOOR PLANSAND ROOF PLANS - QUANTITY OF ACUNITS AND CU UNITS FOR EACH.PROVIDE WIRING AND RACEWAYS FORALL SENSORS AND INTERLOCK WIRINGOF VRF SYSTEMS.

TYPICAL SYSTEMFAN COIL UNIT

AC

S

RSRL

WALL

GALV. STEEL DUCTWORK WITH1" THICK ACOUSTICAL FIBROUSGLASS INSULATION LINER. SEEPLANS FOR DUCT SIZE

CEILING

TAD

PLENUM RA

VANED ELBOW WITHOPEN END UP - TYPICAL

ACOUSTICALLY SEAL TAD AIR TIGHTALL AROUND WALL PENETRATION ONBOTH SIDES OF WALL - TYPICAL

PLENUM RA

TOP CONNECTOR FOR REGISTERNECK SIZES, 16"Ø AND 22"Ø.

STAINLESS STEELDRAW BAND -TYPICAL.

PERFORATED OR EGGCRATECEILING REGISTER.

16 INCH DEEP PLENUM.

CEILING TILE ANDSUSPENSION.

SIDE CONNECTION FORREGISTER NECK SIZES, 8"Ø,10"Ø AND 12"Ø.

1" THICK DUCT WRAP INSULATIONAT RETURN REGISTER

BALANCING DAMPERAT SUB MAIN TAKE-OFF

FIVE FEET MAXIMUMLENGTH. USE FLEXIBLEDUCT AS CONNECTOR ONLY.

BRANCHDUCTWORK.

V o

r

NOTES:1. r/H EQUALS MINIUMUM OF 1.5.2. 45° SMOOTH RADIUS ELBOWS.3. PROVIDE OFFSETS OF CONFIGURATIONS INDICATED ON DUCTWORK FLOOR PLANS.4. COORDINATE OTHER TRADES TO MINIMIZE FIELD REQUIRED OFFSETS.5. PROVIDE A MINIMUM OF 6" STRAIGHT DUCT BETWEEN FITTINGS.

H

CLEVIS HANGER

INSULATION

PIPING

DOUBLE NUTS AND WASHERS

CUT SECTIONS OF SPECIFIEDINSULATION TO FILL VOID MSS TYPE 39 STEEL PIPING SADDLE TACK WELDED

TO PIPE. DELETE SADDLE ON CHILLED WATERPIPING. PROVIDE MSS TYPE 40 STEEL PIPE SHIELDSON ALL CHILLED WATER PIPING THE HANDLE.

THREADED HANGER ROD TOATTACHMENT AS SPECIFIED - TYP.

PROVIDE SPRING SUSPENSIONISOLATORS WHERE SPECIFIED

PIPING

INSULATION

CUT SECTION OF SPECIFIEDINSULATION TO FILL VOID

MSS TYPE 39 STEEL PIPE SADDLE TACKWELDED TO PIPE. DELETE SADDLE ON CHILLEDWATER PIPING. PROVIDE MSS TYPE 40 STEELPIPE SHIELDS ON ALL CHILLED WATER PIPING.

THREADED HANGER ROD TOATTACHMENT AS SPECIFIED(TYIPCAL).

PROVIDE SPRINGSUSPENSION ISOLATORSWHERE SPECIFIED.

ROLLER HANGER

SEALING ANDANCHORING COLLAR

CENTERPIPE INSLEEVE

STANDARD WEIGHTSTEEL PIPE CASTINTO CONCRETE ORSET IN MASONRY

FABRICATED 3" 304 S.S.ESCUTCHEON PLATE

BACK UPMATERIAL

EXTERIOR WALL SECTION

COAT EXTERIORSURFACES WITHTAR COMPOUND

SEAL SLEEVEWITH SEALANT

No 77673

STATE OF

RK S.ERED

PR

OF

NSSOI

ELA ENGIN

EER

LICENSE

F LO RIDA

EED

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

11:41

:3 2 A

M

MH501

MECHANICALDETAILS

VLM

DSR

NOT TO SCALE2 CEILING DIFFUSER AND REGISTER CONNECTION

NOT TO SCALE1 RECTANGULAR ELBOWS

NOT TO SCALE3 TRANSFER AIR GRILLE DETAIL

NOT TO SCALE6 SPLIT SYSTEM REFRIGERANT PIPING DIAGRAMNOT TO SCALE5 TYPICAL VARIABLE REFRIGERANT FLOW SYSTEM

ADD ALTERNATE 1 - MECHANICAL

NOT TO SCALE4 TRANSFER AIR DUCT

NOT TO SCALE7 RETURN, EXHAUST AND TRANSFER AIR REGISTER CONNECTIONNOT TO SCALE8 TYPICAL DUCTWORK OFFSET

NOT TO SCALE9 TYPICAL PIPE CLEVIS HANGERNOT TO SCALE10 TYPICAL PIPE HANGER ROLLER

NOT TO SCALE11 TYPICAL PIPE SLEEVES THRU WALLS


1 ADDENDUM 1 10-23-15

AIR TERMINAL DEVICE SCHEDULE

(CFM RANGE)NECK SIZE/

12Ø/(350-500)10Ø/(225-345)8Ø/(0-220)

MOUNTING

LAY-IN

LAY-INTG-A 24X24 EGG CRATE

NOM. FACE

CD-A

MARK

24X24

DIMENSIONSFACE

LOUVERED

TYPE

ALUMINUM 35 22X22

MATERIAL

ALUMINUM

MAX.

35

NC

-

-

BASIS OF DESIGN

-

-

REMARKS

-METALAIRE5700-6 AL

GENERAL NOTES:1. PROVIDE SQUARE TO ROUND THROAT ADAPTERS - ROUND RUNOUT SIZE SAME AS THROAT (I.E. 8X8 USE 8Ø) FOR ALL CEILING DIFFUSERS OR PROVIDE

DIFFUSERS OR PROVIDE DIFFUSERS WITH INTERNAL ROUND THROAT CONNECTION.2. REFER TO DETAILS FOR DUCT CONNECTIONS TO RETURN, EXHAUST, AND TRANSFER GRILLES USING PLENUM CONNECTIONS AS DETAILED.3. COLOR TO MATCH EXISTING DIFFUSERS AND GRILLES.4. LOUVERED AREA OF DIFFUSERS, REGISTERS, AND GRILLES SHALL BE FULL NOMINAL FACE DIMENSIONS. REDUCED LOUVER AREAS ARE NOT

ACCEPTABLE.

LAY-INRR-A 24X24 EGG CRATE ALUMINUM 35 12Ø/(350-500)

AHU BALANCING SCHEDULE

MARK (CFM)(CFM)

SUPPLYAIR

AHU/B1.1

10,050 3,270AHU/B2.1

9,500 1,010

AHU/B1.4 5,000 750

OA

10,050 3,270AHU/B2.1

GENERAL NOTES:1. VERIFY ALL AIR VOLUMES WITH PLANS PRIOR TO BALANCING SYSTEMS2. TABS CONTRACTOR TO REVIEW SYSTEMS AND NOTIFY MECHANICAL CONTRACTOR IF ADDITIONAL BALANCING DAMPERS ARE REQUIRED DURING CONSTRUCTION.3. REFER TO PLANS FOR UNIT AIR BALANCE AND ADDITIONAL NOTES.4. PROVIDE TABS OF EQUIPMENT NOTED ABOVE AT END OF CONSTRUCTION AS INDICATED.5. BALANCE EXISTING AIR VALVES AS NOTED ON PLANS.6. REFER TO PLANS FOR BALANCING OF CEILING DEVICES AND TRAVERSE MEASUREMENTS REQUIRED DURING CONSTRUCTION.7. REFER TO ARCHITECTURAL PLANS FOR ADDITIONAL INFORMATION REGARDING CONSTRUCTION AND LIMITS OF WORK.

ENT. AIR(°F)

COOLING

AIR(CFM)LOCATIONMARK DB

SUPPLYENTAIREERWB VOLTSMCACOP PHASE

ELECTRICAL

HEATING

HERTZ EQUIPMENT

FCU/B2.2 436 7812 12 7013.515.165 12080.32.6 60

SPIT SYSTEM FAN COIL UNIT SCHEDULE

RELATEDTYPE/

FCU/B2.1 436 7812 12 7013.515.165 12080.32.6 60CASSETTE/104 CU/B2.1

ELECTRICALCOOLING

LOCATIONMARK (MBH)TOT CAP

(°F)

HEATING

AMBAMB(°F) (MBH)

TOT CAPVOLTS

COMPRESSORS

CAPACITY(%)PHASE NO(RLA)

POWERNO REFRIGERANT BASIS OF DESIGN(A)

DAIKIN RXYMQ48PVJU

SPLIT SYSTEM CONDENSING UNIT SCHEDULE

MINMCA

CU/B2.1 47.5 4795 52.5 208 2911 -1 410a27SEE PLANS 23.3

CONDENSERFAN

FCU/B2.3 436 7812 12 7013.515.165 12080.32.6 60

FAN DATA

(IN H20)

EXTERNALSTATIC

-

(HP)

MOTORSIZE

-

AIR(CFM)

OUTDOOR

0

0

0

TOTAL SENSIBLE TOTAL(MBH)(MBH) (MBH)

FCU/B2.4 436 7812 12 7013.515.165 12080.32.6 600

- -

- -

- -

BASIS OF DESIGN

DAIKIN FXZQ12MVJU9

DAIKIN FXZQ12MVJU9

DAIKIN FXZQ12MVJU9

DAIKIN FXZQ12MVJU9

CASSETTE/103

CASSETTE/102

CASSETTE/101

CU/B2.1

CU/B2.1

CU/B2.1

SEER

15.1

COP

2.6

METALAIRECC5-6

METALAIRECC5-6

No 77673

STATE OF

RK S.ERED

PR

OF

NSSOI

ELA ENGIN

EER

LICENSE

F LO RIDA

EED

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

11:41

:3 3 A

M

MH801

MECHANICALSCHEDULES

VLM

DSR

ADD ALTERNATE 1 - MECHANICAL

1

1


1 ADDENDUM 1 10-23-15

M

E

J

NOTES:SHEET NOTES:A. SEE REFLECTED CEILING PLANS ON SHEETS B1-AE410 AND B2-AE410 FOR EXACT

LOCATION OF LUMINAIRES AND CEILING MOUNTED DEVICES.B. INSTALL ALL EQUIPMENT AND DEVICES AT THE HEIGHT INDICATED ON THIS

SHEET UNLESS OTHERWISE NOTED. REFER TO ARCHITECTURAL INTERIORELEVATIONS FOR SPECIAL MOUNTING HEIGHTS AND LOCATIONS OF ELECTRICALDEVICES. MOUNTING HEIGHTS AND LOCATIONS INDICATED ON ARCHITECTURALELEVATIONS TAKE PRECEDENCE OVER MOUNTING HEIGHTS AND LOCATIONSINDICATED ON THE ELECTRICAL PLANS.

C. LUMINAIRES INDICATED AS FOLLOWS: UPPER CASE LETTER WITH NUMERALDENOTES FIXTURE TYPE (SEE LUMINAIRE SCHEDULE), LOWER CASE LETTER (IFSHOWN) DENOTES SWITCHING ARRANGEMENT.

D. WHERE DEVICES ARE INDICATED TO BE MOUNTED ABOVE A COUNTERTOP,MOUNT DEVICE SUCH THAT BOTTOM OF COVER PLATE IS 2" ABOVE TOP OF BACKSPLASH. IF THERE IS NO BACK SPLASH, MOUNT DEVICE 2" ABOVE FINISHEDCOUNTER TOP SURFACE TO BOTTOM OF DEVICE COVER PLATE.

E. WHERE MULTIPLE TOGGLE SWITCHES ARE SHOWN TO BE MOUNTED ADJACENTTO ONE ANOTHER, MOUNT SWITCHES IN A SINGLE BOX UP TO 4-GANG (NORMALAND EMERGENCY CIRCUITS SHALL NOT OCCUPY THE SAME ENCLOSURE).

F. ALL MATERIALS AND EQUIPMENT SHALL BE LISTED AS COMPLYING WITH THEAPPLICABLE STANDARDS OF UNDERWRITER'S LABORATORIES, INC.

G. CONDUCTOR AMPACITIES ARE BASED ON 60° C COPPER FOR #12 AWG THROUGH#1 AWG CONDUCTORS. CONDUCTOR AMPACITIES ARE BASED ON 75° C COPPERFOR CONDUCTORS LARGER THAN #1 AWG.

H. ALL CONDUIT SIZES ARE BASED ON ELECTRICAL METALLIC TUBING (EMT) WITHTYPE THHN/THWN COPPER CONDUCTORS. ADJUST CONDUIT SIZE AS REQUIREDFOR OTHER CONDUIT MATERIALS AND CONDUCTOR TYPES.

I. WHERE CONDUIT IS ROUTED ABOVE THE FINISHED CEILING, COORDINATELOCATION AND ROUTING WITH OTHER TRADES AND SYSTEMS TO PROVIDE ACOORDINATED INSTALLATION AND TO ASSURE MAXIMUM ACCESSIBILITY TO ALLSYSTEMS. ALL JUNCTION BOXES AND PULL BOXES SHALL REMAIN ACCESSIBLE.

J. DO NOT MOUNT ELECTRICAL OR COMMUNICATIONS DEVICES, OUTLETS, ORBOXES BACK TO BACK UNLESS SPECIFICALLY INDICATED OTHERWISE NOTED. INWALLS WITH A STC RATING OF 5O OR MORE, OFFSET OUTLETS OR BOXES INOPPOSITE SIDES OF THE WALL BY AT LEAST TWO STUD CAVITIES.

K. PROVIDE SEPARATE NEUTRAL CONDUCTOR FOR EACH 120V BRANCH CIRCUIT.MULTIPLE 120V, 20A BRANCH CIRCUITS MAY BE COMBINED IN A SINGLE 1/2"CONDUIT HOME RUN, MAXIMUM OF (3) CIRCUIT PER HOME RUN.

ABBREVIATIONS

CLOSED CIRCUIT TELEVISION

ABOVE FINISHED FLOORABOVE FINISHED GRADE

AUTOMATIC TRANSFER SWITCH

BELOW FINISHED GRADE

ELECTRIC UNIT HEATERELECTRIC WATER COOLERELECTRIC WATER HEATER

ELECTRICAL METALLIC TUBING

ENGINE GENERATOR SET

BELOW FINISHED CEILING

EWH

FLUOR

FA

GEN

EXISTEXH

EQUIP

EWCEUH

EMTEF

FLUORESCENT

FIRE ALARM

EXHAUSTEXISTING

EXHAUST FAN

EQUIPMENT

CLG

DISCDWGEA

CU

CL

CABCCTVCKT

BFG

CEILINGCENTERLINE

DISCONNECT(ING)DRAWING(S)

EACH

COPPER

CABINET

CIRCUIT

CONDUIT

AFG

ATSBFC

A

AFF

NATIONAL ELECTRICAL CODE

POLYVINYL CHLORIDE

UNLESS OTHERWISE NOTED

MANUAL TRANSFER SWITCH

XFMR

V

WP

VA

TEL

UON

TRANSFORMER

TELEPHONE

VOLT-AMPERES

WEATHER PROOF

VOLTS

MTS

PVCPNL

REC

NECNC

MTR

MTGMTD

MISCMIN

NURSE CALL

RECEPTACLE

PANEL

MINIMUMMISCELLANEOUS

MOUNTEDMOUNTING

MOTOR

HEATING/VENTILATING / AIRCONDITIONING

KILO-VOLTS-AMPERES

KILO-WATT-HOURS

MOTOR CONTROL CENTER

LOCAL AREA NETWORKLAN

MCC

MHMFR

MAX

LTG

KVA

KWHKW

KVJB

METAL HALIDE

LIGHTING

MANUFACTURER

MAXIMUM

JUNCTION BOXKILO-VOLTS

KILO-WATTS

HVAC

HVINC

HP HORSEPOWER

HIGH VOLTAGEINCANDESCENT

FLA FULL LOAD AMPERES

ABOVE FINISHED CEILINGAFC

W WATTS

TYP TYPICAL

GFCI GROUND FAULT CIRCUIT INTERRUPTER

CURRENT TRANSFORMERSCT's

KILO-VOLTS-AMPERES REACTIVEKVAR

RGS RIGID GALVANIZED STEELGOVERNMENT FURNISHED,GOVERNMENT INSTALLED

GFGI

C

m METERmm MILLIMETER

AIC AMPERES INTERRUPTING CAPACITY

MCB MAIN CIRCUIT BREAKER

MCP MOTOR CIRCUIT PROTECTOR

HAND-OFF-AUTOMATIC

HIGH INTENSITY DISCHARGEHIGH PRESSURE SODIUM

HID

HOAHPS

GNDHGT

GROUNDHEIGHT

GFP GROUND FAULT PROTECTION

AMPERES

WIRING DEVICESSUBSCRIPTS INDICATE THE FOLLOWING: (FOR ALL RECEPTACLES)

MOUNT DEVICE ABOVE THE COUNTER TOP. SEE SHEET NOTE DON THIS SHEET FOR REQUIREMENTS.

MOUNT DEVICE AT 48" AFF TO CENTER. OTHER MOUNTINGHEIGHTS AS INDICATED.

OC -

+48" -

SPECIAL RECEPTACLE WITH NEMA CONFIGURATION AS INDICATED. WALLMOUNT AT 18" AFF TO TOP UON.

NEMA

MANUAL MOTOR STARTER WITH MELTING ALLOY HEATER ELEMENTS WITHRATING AS REQUIRED FOR EQUIPMENT MOTOR SERVED. MOUNT ADJACENTTO EQUIPMENT SERVED. SUBSCRIPTS INDICATE THE FOLLOWING:

M

MANUAL MOTOR STARTER WITH MELTING ALLOY HEATER ELEMENTS.M -

EXISTING RECESSED FLOOR BOX WITH SINGLE-GANG COVER AND DUPLEXRECEPTACLE.

EXISTING RECESSED FLOOR BOX WITH SEPARATE POWER AND COMMUNICATIONSCOMPARTMENTS.

20A, 125V SIMPLEX RECEPTACLE. WALL MOUNT AT 18" AFF TO TOP UON.

20A, 125V DUPLEX RECEPTACLE. WALL MOUNT AT 18" AFF TO TOP UON.

EXISTING 20A, 125V DUPLEX RECEPTACLE FOR ENTERTAINMENT TELEVISION WITHCOAXIAL CONNECTION IN A DOUBLE GANG BOX WITH COMMON COVER PLATEAND DIVIDER.

TV

1ALN1-1

WHERE SHOWN ADJACENT TO ANY WIRING DEVICE, SUBSCRIPT INDICATESBRANCH CIRCUIT NUMBER TO WHICH THE DEVICE IS CONNECTED. BRANCHCIRCUIT SHALL BE 1/2"C - 2#12 + 1#12G.

SUBSCRIPTS INDICATE THE FOLLOWING:

MOMENTARY CONTACT SWITCH FOR PROJECTION SCREEN.MC -

TWO 20A, 125V DUPLEX RECEPTACLES IN A 2-GANG BOX WITH A COMMON COVERPLATE. WALL MOUNT AT 18" AFF TO TOP UON.

20A, 125V FLUSH CEILING-MOUNTED DUPLEX RECEPTACLE.

EQUIPMENT CONNECTIONS

MOTOR CONNECTION.

JUNCTION BOX OR PULL BOX.

CONNECTION TO EQUIPMENT LEADS, TERMINAL STRIPS OR CONTROL PANELINCLUDING ALL CONDUCTORS, CONDUIT, FLEXIBLE CONDUIT, JUNCTION BOXES,CONNECTORS, FITTINGS, ETC REQUIRED FOR PROPER CONNECTION.SUBSCRIPT INDICATES THE FOLLOWING.

EDH

EDH - ELECTRIC DUCT HEATERVAV - VARIABLE AIR VALVEP - CEILING MOUNTED PROJECTORPS - PROJECTION SCREEN

1ALN1-1,3,5 HOMERUN TO PANELBOARD.

CONDUIT AND CONDUCTOR SIZE AS INDICATED.

CONDUIT AND CONDUCTORSBRANCH CIRCUIT WIRING IN CONDUIT. 1/2"C - 2#12 + 1#12 GROUNDUNLESS OTHERWISE INDICATED. UNLESS SPECIFICALLY INDICATEDOTHERWISE, SHARING OF A NEUTRAL CONDUCTOR BETWEEN TWO ORMORE BRANCH CIRCUITS IS NOT ALLOWED. PROVIDE ADDITIONALSWITCHED CONDUCTORS OR TRAVELER CONDUCTORS FOR LIGHTINGCIRCUITS AS REQUIRED TO SUPPORT THE INDICATED SWITCHING.

CONDUIT TERMINATION, (C) CAPPED, (B) BUSHED, (G) GROUND BUSHING.

PANELBOARD DESIGNATION.

CIRCUIT DESIGNATION.

3#6 + 1#10G3/4"C

1AHN1-1 INDICATES CIRCUIT NUMBER FOR ALL BRANCH DEVICES (i.e. LIGHTINGFIXTURES, RECEPTACLES, etc..) WITHIN THE ROOM WHERE THE SYMBOL ISPLACED, UNLESS OTHERWISE INDICATED. BRANCH CIRCUIT SHALL BE 1/2"C -2#12 + 1#12G.

POINT OF CONNECTION, EXISTING TO NEW WORK.

POINT OF REMOVAL, DEMOLITION.

KEY NOTE SYMBOL. (SEE KEY NOTES ON INDIVIDUAL DRAWINGS).

CONDUCTOR CONNECTION

ELECTRICAL GROUND

00

MISCELLANEOUS

DIGITAL, WALL MOUNTED SWITCH. MOUNT AT 48" AFF TO CENTER. PROVIDEWATTSTOPPER LMDM-101. WHEN PRESENT, SUBSCRIPTS INDICATE THE FOLLOWING:a,b SWITCH LEG(S) BEING CONTROLLED. PROVIDE SEPARATE PUSHBUTTON

FOR EACH SWITCH LEG.DIMMING OPERATION COMPATIBLE WITH FIXTURES SERVED.D

LIGHTING CONTROL DEVICES

DIGITAL, CEILING MOUNTED, DUAL-TECHNOLOGY OCCUPANCY SENSOR. PROVIDEWATTSTOPPER LMDC-100. WHEN PRESENT, SUBSCRIPT INDICATES THE FOLLOWING:

DIGITAL, CEILING-MOUNTED, DAYLIGHT SENSOR. PROVIDE WATTSTOPPER LMLS-400WITH (1) DIGITAL WIRELESS CONFIGURATION TOOL LMCT-100. WHEN PRESENT,SUBSCRIPTS INDICATE THE FOLLOWING:

D DIMMING OPERATION COMPATIBLE WITH FIXTURES SERVEDa,b DAYLIGHT ZONE(S) BEING CONTROLLED

S ON/OFF SWITCHING OPERATION

WALL MOUNTED, DUAL-TECHNOLOGY OCCUPANCY SENSOR WITH MANUAL OVERRIDE(S). MOUNT AT 48" AFF TO CENTER. PROVIDE WATTSTOPER DSW-301. WHENPRESENT, SUBSCRIPTS INDICATE THE FOLLOWING:a,b SWITCH LEG(S) BEING CONTROLLED. PROVIDE SEPARATE OVERRIDE

PUSHBUTTON FOR EACH SWITCH LEG.THREE-WAY3

a,b SWITCH LEG(S) BEING CONTROLLED

-

-

-

-

-

---

RC

ROOM CONTROLLER

DIGITAL DIMMING ROOM CONTROLLER. PROVIDE WATTSTOPPER LMRC-212 UNLESSNOTED OTHERWISE. SEE SHEET EL601 FOR TYPICAL CONNECTION DIAGRAMS. MOUNTTO JUNCTION BOX ABOVE FINISHED ACCESSIBLE CEILING UNLESS NOTED OTHERWISE.SUBSCRIPTS INDICATE THE FOLLOWING:a,b - WHEN PRESENT, LOWER CASE LETTERS INDICATE SWITCH LEG.

PROVIDE SEPARATE RELAY FOR EACH SWITCH LEG.D - ON/OFF/DIMMING CONTROLLER.

FIRE ALARM SYSTEM

MANUAL PULL STATION. WALL MOUNT AT 48" AFF TO THE OPERATING HANDLE.

ADDRESSABLE INTERFACE DEVICE, CONTROL MODULE. WHEN SHOWN,SUBSCRIPT INDICATES THE DEVICE OR EQUIPMENT BEING CONTROLLED.MOUNT WITHIN 36" OF CONTROL PANEL.

AOM

ADDRESSABLE INTERFACE DEVICE, MONITOR MODULE. MOUNT WITHIN 36" OFCONTROL PANEL.

AIM

COMBINATION VOICE EVACUATION HORN/STROBE UNIT. MOUNT AT 80" AFF TOBOTTOM.

CEILING MOUNTED SMOKE DETECTOR, PHOTOELECTRIC TYPE.

NOTIFICATION APPLIANCE, FIRE ALARM STROBE ONLY. MOUNT AT 80" AFF TOBOTTOM.

FACPFIRE ALARM CONTROL PANEL. SURFACE MOUNT AT 72" AFF TO TOP.

P

TELEPHONE/DATA SYSTEM

COMBINATION VOICE/DATA OUTLET. SEE 1/EG001 FOR TYPICAL OUTLETCONFIGURATION. MOUNT AT 18" AFF TO TOP UNLESS OTHERWISE NOTED.

EXISTING COMBINATION POWER/COMMUNICATION SYSTEM FLOOR BOX.

EXISTING TELECOMMUNICATIONS EQUIPMENT RACK

SUBSCRIPTS INDICATE THE FOLLOWING WHEN PRESENT:

OC - MOUNT ABOVE COUNTER TOP+48" - MOUNTING HEIGHT ABOVE FINISHED FLOOR TO CENTER OTHER THAN

18" AFF TO TOP

1 - NUMERAL INDICATES QUANTITY OF JACKS

NORMAL POWER.

BATTERY BALLAST

EXIT SIGN, CEILING OR PENDANT MOUNTED. SHADED PORTION DENOTESFACE(S). DIRECTIONAL ARROWS AS INDICATED.

EXIT SIGN, WALL MOUNTED. SHADED PORTION DENOTES FACE(S).DIRECTIONAL ARROWS AS INDICATED. MOUNT 4" ABOVE TOP OF DOORJAMB TO BOTTOM OF FIXTURE, UNLESS OTHERWISE NOTED.

LUMINAIRES

CEILING MOUNTED 2'x4' FLUORESCENT FIXTURE, UNLESS OTHERWISE NOTED.

BATTERY BALLAST IDENTIFICATION (TYPICAL FOR ALL FIXTURES)

LUMINAIRES:

CEILING MOUNTED 2'x2' FLUORESCENT FIXTURE, UNLESS OTHERWISE NOTED.

CEILING MOUNTED, SURFACE MOUNTED OR SUSPENDED FLUORESCENTFIXTURE AS INDICATED IN THE LIGHTING FIXTURE SCHEDULE.

EMERGENCY LIGHTING UNIT.

1AHN1-1

WHERE SHOWN ADJACENT TO ANY LIGHTING FIXTURE, SUBSCRIPTINDICATES BRANCH CIRCUIT NUMBER TO WHICH THE LIGHTING FIXTURE ISCONNECTED. BRANCH CIRCUIT SHALL BE 1/2"C - 2#12 + 1#12G.

CEILING MOUNTED DOWNLIGHT.

EXISTING CEILING MOUNTED SPEAKER. SUBSCRIPTS INDICATE PAGINGZONE AND VOLUME CONTROL

EXISTING WALL MOUNTED VOLUME CONTROL.

V-H01C01

V-H01

SOUND SYSTEM

S

V

M EXISTING MICROPHONE.

EXISTING WALL MOUNT PROXIMITY-TYPE CARD READER CREDENTIALDEVICE.EXISTING WALL MOUNT COMBINATION PROXIMITY-TYPE CARD READER ANDKEYPAD CREDENTIAL DEVICE.EXISTING WALL MOUNT KEYPAD CREDENTIAL DEVICE.

EXISTING VOLUMETRIC MOTION DETECTOR.

EXISTING SURFACE MOUNT ELECTRONIC SECURITY SYSTEM BACKBONETERMINAL CABINET.

EXISTING SURFACE MOUNT ACCESS CONTROL AND ALARM SYSTEMEQUIPMENT CABINET/CONTROLLER.

EXISTING SURFACE MOUNT INTRUSION DETECTION SYSTEMCABINET/CONTROLLER.

CR

CR KP

KP

MD

ESSC

ACAS

IDS

ACCESS CONTROL

EXISTING DOOR CONTACTOR.DC

LINE WEIGHT LEGEND

DASHED LINES INDICATE EQUIPMENT TO BE REMOVED.

SCREENED LINES INDICATE EXISTING EQUIPMENT TO REMAIN.

SOLID LINES INDICATE EQUIPMENT PROVIDED UNDER THIS CONTRACT.

NOTE: SUBSCRIPTS SHOWN ADJACENT TO ANY DVICE OR SYMBOL SHOWNON THIS PLAN INDICATE THE FOLLOWING:

E - DEVICE IS EXISTING TO REMAINER - DEVICE IS EXISTING TO BE RELOCATED

2

2

2

AV

AV SYSTEM

AUDIO/VISUAL SYSTEM BOX. 4" SQUARE X 2 1/8" DEEP RECESSED BOX WITHSTAINLESS STEEL COVER PLATE. PROVIDE 1 1/2" DIAMETER OPENING WITHGROMMET IN THE CENTER OF THE COVER PLATE. PROVIDE 1 1/4" CONDUIT FROMBACK BOX TO THE CLASSROOM ACCESSIBLE CEILING SPACE, PROVIDE INSULATEDBUSHING AT CONDUIT TERMINATION. SEE 11/B1-AE201 FOR MOUNTING HEIGHTAND RELATIVE PLACEMENT.

SUBSCRIPTS INDICATE THE FOLLOWING:L - LOWER MOUNTED AUDIO/VISUAL SYSTEM BOXU - UPPER MOUNTED AUDIO/VISUAL SYSTEM BOX

L

TS 4 11/16” X 2 1/8” DEEP BOX WITH TWO GANG PLASTER RING FOR TOUCH SCREENCONTROLLER. VERIFY BOX SIZE AND PLASTER RING CONFIGURATION WITHTHE OWNER PRIOR TO ROUGH-IN. PROVIDE 1” CONDUIT FROM BACK BOX TOTHE CLASSROOM ACCESSIBLE CEILING SPACE, PROVIDE INSULATED BUSHINGAT CONDUIT TERMINATION. SEE 11/B1-AE201 FOR MOUNTING HEIGHT ANDRELATIVE PLACEMENT.

2

2

2

EXISTING SURGE PROTECTIVE DEVICE. SEE SURGE PROTECTIVE DEVICE.

POWER DISTRIBUTION

CIRCUIT BREAKER WITH NUMBER OF POLES AND TRIP RATING ASINDICATED.

PANELBOARD

WHEN PRESENT, INDICATES PANELBOARD WITH MAIN CIRCUITBREAKER. SEE PANEL SCHEDULE FOR SIZE. IF NOTPRESENT, PANELBOARD WITH MAIN LUGS ONLY.WHEN PRESENT, INDICATES PANELBOARD WITH FEED THROUGH LUGS.

1AHN1

PANELBOARD, SURFACE MOUNTED AT 72" AFF TO TOP.

240V, 2P, NON-FUSED DISCONNECT SWITCH. ALL DISCONNECTSWITCHES SHALL BE NEMA 1 UNLESS OTHERWISE INDICATED.MOUNT AT 72" AFF TO TOP

30A3R

SOLID LINES INDICATE EQUIPMENT PROVIDED BY THIS CONTRACT

SCREENED LINES INDICATE EXISTING EQUIPMENT

INDICATES THE CURRENT RATINGINDICATES NEMA ENCLOSURE OTHER THAN NEMA 1 (3R, 4X, ETC...)

3P100 A

SPD

FREE STANDING SWITCHBOARD.

DETAIL CODES:

RJ45 8 POSITION CATEGORY 6 MODULAR JACK.-B BLANK INSERT.-MFP MODULAR FACE PLATE.-LBL LABEL SPACE.-1"C 1" CONDUIT TO ACCESSIBLE CEILING SPACE. PROVIDE

INSULATED BUSHING AT TERMINATION ABOVE CEILING.-

3/4"C 3/4" CONDUIT TO ACCESSIBLE CEILING SPACE.-

1"C

LBL

LBL

MFPRJ45

BRJ45

HC HORIZONTAL CABLE(S) BY OWNER.-

HC

4 11/16" X 2 1/8" BACK BOX WITHSINGLE GANG PLASTER RING.

No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS

SIMON ECHEVERRY - EL PE0075040

10/23

/2015

12:56

:3 3 P

M

EG001

ELECTRICALSYMBOLS LEGEND

NGZ

SAE

LIGHTING FIXTURE SCHEDULEFIXTURE

TYPE DESCRIPTION MANUFACTURER MODEL VOLTAGELAMP

QUANTITY LAMP DRIVER MOUNTING NOTESB1 2' X 2' STATIC LED TROFFER WITH OPTIMIZED SMOOTH LENS, COLD ROLLED STEEL HOUSING WITH HEMMED SIDES AND ENDS AND A BAKED WHITE ENAMEL SMOOTH FINISH. 3200 LUMEN, 4,000K COLOR

TEPERATURE.CREE ZR22-32L-40K-10V 120/277 - LED 0-10V DIMMING RECESSED

B1B 2' X 2' STATIC LED TROFFER WITH OPTIMIZED SMOOTH LENS, COLD ROLLED STEEL HOUSING WITH HEMMED SIDES AND ENDS AND A BAKED WHITE ENAMEL SMOOTH FINISH. 3200 LUMEN, 4,000K COLORTEPERATURE.

CREE ZR22-32L-40K-10V-EB14 120/277 - LED 0-10V DIMMING RECESSED EMERGENCY BACKUP BATTERY INVERTER - 1400 LUMENS

SCALE: NOT TO SCALETYPICAL VOICE/DATA OUTLET DETAIL1

2

2

2

2

2

2

2


2 ADDENDUM 1 10-23-15

SECTION 265100 - INTERIOR LIGHTINGPART 1 - GENERAL

1.1 SUMMARYA. Section Includes:

1.Interior lighting fixtures.2.Lighting fixture supports.

1.2 ACTION SUBMITTALSA. Product Data: For each type of lighting fixture, arranged in order of fixture designation. Include data on features, accessories, and finishes.

1.3 QUALITY ASSURANCEA. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.B. Comply with NFPA 70.

PART 2 - PRODUCTS2.1 MANUFACTURERS

A. Products: Subject to compliance with requirements, provide product indicated on drawings or equivalent.2.2 GENERAL REQUIREMENTS FOR LIGHTING FIXTURES AND COMPONENTS

A. Recessed Fixtures: Comply with NEMA LE 4 for ceiling compatibility for recessed fixtures.B. Metal Parts: Free of burrs and sharp corners and edges.C. Sheet Metal Components: Steel unless otherwise indicated. Form and support to prevent warping and sagging.D. Doors, Frames, and Other Internal Access: Smooth operating, free of light leakage under operating conditions, and designed to permit servicing without use of tools. Designed to prevent doors, frames, lenses, diffusers, and other components from falling accidentally during servicing and when secured in operating position.

2.3 LIGHTING FIXTURE SUPPORT COMPONENTSA. Comply with Section 260529 "Hangers and Supports for Electrical Systems" for channel- and angle-iron supports and nonmetallic channel and angle supports.B. Wires: ASTM A 641/A 641M, Class 3, soft temper, zinc-coated steel, 12 gage.

PART 3 - EXECUTION3.1 INSTALLATION

A. Lighting fixtures: Set level, plumb, and square with ceilings and walls. Install lamps in each fixture.B. Comply with NFPA 70 for minimum fixture supports.C. Connect wiring according to Section 260519 "Low-Voltage Electrical Power Conductors and Cables."

END OF SECTION 265100

SECTION 260519 - LOW-VOLTAGE ELECTRICAL POWER CONDUCTORS AND CABLESPART 1 - GENERAL


1.Building wires and cables rated 600 V and less.2.Connectors, splices, and terminations rated 600 V and less.

1.2 ACTION SUBMITTALSA. Product Data: For each type of product.

PART 2 - PRODUCTS2.1 CONDUCTORS AND CABLES

A. Copper Conductors: Comply with NEMA WC 70.B. Conductor Insulation: Comply with NEMA WC 70 Types THHN-2 and THWN-2.

2.2 CONNECTORS AND SPLICESA. Description: Factory-fabricated connectors and splices of size, ampacity rating, material, type, and class for application and service indicated.

2.3 SYSTEM DESCRIPTIONA. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.B. Comply with NFPA 70.

PART 3 - EXECUTION3.1 CONDUCTOR MATERIAL APPLICATIONS

A. Branch Circuits: Copper. Solid for No. 10AWG and smaller; stranded for No. 8AWG and larger.3.2 CONDUCTOR INSULATION AND MULTICONDUCTOR CABLE APPLICATIONS AND WIRING METHODS

A. Branch Circuits Concealed in Ceilings, Walls, and Partitions: Type THHN-2-THWN-2, single conductors in raceway.3.3 INSTALLATION OF CONDUCTORS AND CABLES

A. Conceal cables in finished walls, and ceilings.B. Complete raceway installation between conductor and cable termination points according to Section 260533 "Raceways and Boxes for Electrical Systems" prior to pulling conductors and cables.C. Use manufacturer-approved pulling compound or lubricant where necessary; compound used must not deteriorate conductor or insulation. Do not exceed

manufacturer's recommended maximum pulling tensions and sidewall pressure values.D. Use pulling means, including fish tape, cable, rope, and basket-weave wire/cable grips, that will not damage cables or raceway.E. Support cables according to Section 260529 "Hangers and Supports for Electrical Systems."

3.4 CONNECTIONSA. Tighten electrical connectors and terminals according to manufacturer's published torque-tightening values. If manufacturer's torque values are not indicated, use those specified in UL 486A-486B.B. Make splices, terminations, and taps that are compatible with conductor material and that possess equivalent or better mechanical strength and insulation ratings than unspliced conductors.C. Wiring at Outlets: Install conductor at each outlet, with at least 6 inches of slack.

3.5 IDENTIFICATIONA. Identify and color-code conductors and cables according to Section 260553 "Identification for Electrical Systems."B. Identify each spare conductor at each end with identity number and location of other end of conductor, and identify as spare conductor.


SECTION 260526 - GROUNDING AND BONDING FOR ELECTRICAL SYSTEMSPART 1 - GENERAL

1.1 SUMMARYA. Section includes grounding and bonding systems and equipment.

1.2 ACTION SUBMITTALSA. Product Data: For each type of product indicated.

PART 2 - PRODUCTS2.1 MANUFACTURERS2.2 CONDUCTORSA. Insulated Conductors: Copper wire or cable insulated for 600 V unless otherwise required by applicable Code or authorities having jurisdiction.B. Bare Copper Conductors:

1.Solid Conductors: ASTM B 3.2.Stranded Conductors: ASTM B 8.

2.3 CONNECTORSA. Listed and labeled by an NRTL acceptable to authorities having jurisdiction for applications in which used and for specific types, sizes, and combinations of

conductors and other items connected.PART 3 - EXECUTION

3.1 APPLICATIONSA. Conductors: Install solid conductor for No. 8 AWG and smaller, and stranded conductors for No. 6 AWG and larger unless otherwise indicated.

3.2 EQUIPMENT GROUNDINGA. Install insulated equipment grounding conductors with all feeders and branch circuits.B. Install insulated equipment grounding conductors with the following items, in addition to those required by NFPA 70:

1.Branch circuits.2.Lighting circuits.3.Receptacle circuits.4.Single-phase motor and appliance branch circuits.

3.3 INSTALLATIONA. Grounding Conductors: Route along shortest and straightest paths possible unless otherwise indicated or required by Code. Avoid obstructing access or placing

conductors where they may be subjected to strain, impact, or damage.3.4 FIELD QUALITY CONTROL

A. Perform tests and inspections. Inspect physical and mechanical condition. Verify tightness of accessible, bolted, electrical connections with a calibrated torque wrench according to manufacturer's written instructions.


PART 3 - EXECUTION3.1 APPLICATIONS

A. Conductors: Install solid conductor for No. 8 AWG and smaller, and stranded conductors for No. 6 AWG and larger unless otherwise indicated.3.2 EQUIPMENT GROUNDING

A. Install insulated equipment grounding conductors with all feeders and branch circuits.B. Install insulated equipment grounding conductors with the following items, in addition to those required by NFPA 70:

1.Branch circuits.2.Lighting circuits.3.Receptacle circuits.4.Single-phase motor and appliance branch circuits.

3.3 INSTALLATIONA. Grounding Conductors: Route along shortest and straightest paths possible unless otherwise indicated or required by Code. Avoid obstructing access or placing

conductors where they may be subjected to strain, impact, or damage.3.4 FIELD QUALITY CONTROL

A. Perform tests and inspections. Inspect physical and mechanical condition. Verify tightness of accessible, bolted, electrical connections with a calibrated torque wrenchaccording to manufacturer's written instructions.


SECTION 260529 - HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMSPART 1 - GENERAL

1.1 SUMMARYA. Section includes:

1.Hangers and supports for electrical equipment and systems.1.2 QUALITY ASSURANCE

A. Comply with NFPA 70.PART 2 - PRODUCTS

2.1 SUPPORT, ANCHORAGE, AND ATTACHMENT COMPONENTSA. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorporated into the Work include, but are not

limited to, the following:1.Manufacturers: Subject to compliance with requirements, provide products by one of the following:

a. Allied Tube & Conduit.b. Cooper B-Line, Inc.c.ERICO International Corporation.d. GS Metals Corp.e. Thomas & Betts Corporation.f. Unistrut; Atkore International.g. Wesanco, Inc.

2.Metallic Coatings: Hot-dip galvanized after fabrication and applied according to MFMA-4.3.Painted Coatings: Manufacturer's standard painted coating applied according to MFMA-4.4.Channel Dimensions: Selected for applicable load criteria.

B. Raceway and Cable Supports: As described in NECA 1 and NECA 101.C. Conduit and Cable Support Devices: Steel hangers, clamps, and associated fittings, designed for types and sizes of raceway or cable to be supported.D. Mounting, Anchoring, and Attachment Components: Items for fastening electrical items or their supports to building surfaces include the following:

1.Clamps for Attachment to Steel Structural Elements: MSS SP-58, type suitable for attached structural element.2.Through Bolts: Structural type, hex head, and high strength. Comply with ASTM A 325.3.Toggle Bolts: All-steel springhead type.4.Hanger Rods: Threaded steel.

PART 3 - EXECUTION3.1 APPLICATION

A. Comply with NECA 1 and NECA 101 for application of hangers and supports for electrical equipment and systems except if requirements in this Section are stricter.B. Maximum Support Spacing and Minimum Hanger Rod Size for Raceway: Space supports for EMT as required by NFPA 70. Minimum rod size shall be 1/4 inch in

diameter.C. Spring-steel clamps designed for supporting single conduits without bolts may be used for 1-1/2-inch and smaller raceways serving branch circuits and

communication systems above suspended ceilings and for fastening raceways to trapeze supports.3.2 SUPPORT INSTALLATION

A. Comply with NECA 1 and NECA 101 for installation requirements except as specified in this Article.B. Raceway Support Methods: In addition to methods described in NECA 1, EMT may be supported by openings through structure members, as permitted in NFPA 70.C. Strength of Support Assemblies: Where not indicated, select sizes of components so strength will be adequate to carry present and future static loads within

specified loading limits. Minimum static design load used for strength determination shall be weight of supported components plus 200 lb.D. Mounting and Anchorage of Surface-Mounted Equipment and Components: Anchor and fasten electrical items and their supports to building structural elements by

the following methods unless otherwise indicated by code:1.To Steel: Beam clamps (MSS Type 19, 21, 23, 25, or 27) complying with MSS SP-69.2.To Light Steel: Sheet metal screws.3.Items Mounted on Hollow Walls and Nonstructural Building Surfaces: Mount disconnect switches, pull and junction boxes, and other devices on slotted-channel

racks attached to substrate.END OF SECTION 260529

SECTION 260533 - RACEWAYS AND BOXES FOR ELECTRICAL SYSTEMSPART 1 - GENERAL


1.Metal conduits, tubing, and fittings.2.Boxes

PART 2 - PRODUCTS2.1 METAL CONDUITS, TUBING, AND FITTINGS

A. Listing and Labeling: Metal conduits, tubing, and fittings shall be listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intendedlocation and application.

B. EMT: Comply with ANSI C80.3 and UL 797.C. FMC: Comply with UL 1; zinc-coated steel.D. Fittings for Metal Conduit: Comply with NEMA FB 1 and UL 514B.

2.2 BOXES, ENCLOSURES, AND CABINETSA. Sheet Metal Outlet and Device Boxes: Comply with NEMA OS 1 and UL 514A.

PART 3 - EXECUTION3.1 RACEWAY APPLICATION

A. Indoors: Apply raceway products as specified below unless otherwise indicated.1.Exposed: EMT.2.Concealed in Ceilings and Interior Walls and Partitions: EMT.

B. Minimum Raceway Size: 3/4-inch trade size.C. Raceway Fittings: Compatible with raceways and suitable for use and location.

3.2 INSTALLATIONA. Comply with NECA 1 and NECA 101 for installation requirements except where requirements on Drawings or in this article are stricter.B. Keep raceways at least 6 inches away from parallel runs of flues and steam or hot-water pipes. Install horizontal raceway runs above water and steam piping.C. Comply with requirements in Section 260529 "Hangers and Supports for Electrical Systems" for hangers and supports.D. Conceal EMT within finished walls, ceilings, and floors unless otherwise indicated. Install conduits parallel or perpendicular to building lines.E. Support conduit within 12 inches of enclosures to which attached.F. Stub-ups to Above Recessed Ceilings:

1.Use a conduit bushing or insulated fitting to terminate stub-ups not terminated in hubs or in an enclosure.G. Install pull wires in empty raceways. Use polypropylene or monofilament plastic line with not less than 200-lb tensile strength. Leave at least 12 inches of slack at

each end of pull wire.H. Flexible Conduit Connections: Comply with NEMA RV 3. Use a maximum of 72 inches of flexible conduit for recessed and semirecessed luminaires.I. Fasten junction and pull boxes to or support from building structure. Do not support boxes by conduits.

3.3 FIRESTOPPINGA. Install firestopping at penetrations of fire-rated floor and wall assemblies.


SECTION 260553 - IDENTIFICATION FOR ELECTRICAL SYSTEMSPART 1 - GENERAL

1.1 SUMMARYA.Section Includes:

1. Identification for conductors.2. Identification for pull and junction boxes.

1.2 QUALITY ASSURANCEA.Adhesive-attached labeling materials, including label stocks, laminating adhesives, and inks used by label printers, shall comply with UL 969.

PART 2 - PRODUCTS2.1 CONDUCTOR IDENTIFICATION MATERIALS

A.Self-Adhesive Vinyl Labels: Preprinted, flexible label laminated with a clear, weather- and chemical-resistant coating and matching wraparound adhesive tapefor securing ends of legend label.PART 3 - EXECUTION

3.1 INSTALLATIONA.Location: Install identification materials and devices at locations for most convenient viewing without interference with operation and maintenance of equipment.B.Self-Adhesive Identification Products: Clean surfaces before application, using materials and methods recommended by manufacturer of identification device.

3.2 IDENTIFICATION SCHEDULEA.Pull and junction boxes: Identify the covers of each junction and pull box of the following systems with self-adhesive vinyl labels with the wiring system legend

and system voltage. System legends shall be as follows:1. Power.

B.Power-Circuit Conductor Identification, 600 V or Less: For conductors in pull and junction boxes, use color-coding conductor tape to identify the phase.1. Color-Coding for Phase and Voltage Level Identification, 600 V or Less: Use colors listed below for ungrounded branch-circuit conductors.

a. Color shall be factory appliedb. Colors for 208/120-V Circuits:

1) Phase A: Black.2) Phase B: Red.3) Phase C: Blue.

c.Colors for 480/277-V Circuits:1) Phase A: Brown.2) Phase B: Orange.3) Phase C: Yellow.


SECTION 262726 - WIRING DEVICESPART 1 - GENERAL

1.1 SUMMARYA.Section Includes:

1. Receptacles and associated device plates.1.2 ACTION SUBMITTALS

A.Product Data: For each type of product.PART 2 - PRODUCTS

2.1 MANUFACTURERSA.Source Limitations: Obtain each type of wiring device and associated wall plate from single source from single manufacturer.

2.2 GENERAL WIRING-DEVICE REQUIREMENTSA.Wiring Devices, Components, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and

application.B.Comply with NFPA 70.

2.3 STRAIGHT-BLADE RECEPTACLESA.Convenience Receptacles, 125 V, 20 A: Comply with NEMA WD 1, NEMA WD 6 Configuration 5-20R, UL 498, and FS W-C-596.

1. Products: Subject to compliance with requirements, provide one of the following:a. Cooper; 5351 (single), CR5362 (duplex).b. Hubbell; HBL5351 (single), HBL5352 (duplex).c.Leviton; 5891 (single), 5352 (duplex).d. Pass & Seymour; 5361 (single), 5362 (duplex).

2.4 WALL PLATESA.Single and combination types shall match corresponding wiring devices.

1. Plate-Securing Screws: Metal with head color to match plate finish.2. Material for Finished Spaces: 0.04-inch- thick, satin finish, 302 grade, stainless steel, with beveled edge, plain.

2.5 FINISHESA.Device Color:

1. Match existing wall plate color unless otherwise indicated or required by NFPA 70 or device listing.B.Wall Plate Color: For plastic covers, match device color.

PART 3 - EXECUTION3.1 INSTALLATION

A.Comply with NECA 1, including mounting heights listed in that standard, unless otherwise indicated.B.Conductors:

1. Do not strip insulation from conductors until right before they are spliced or terminated on devices.2. Strip insulation evenly around the conductor using tools designed for the purpose. Avoid scoring or nicking of solid wire or cutting strands from stranded

wire.3. The length of free conductors at outlets for devices shall meet provisions of NFPA 70, Article 300, without pigtails.4. Existing Conductors:

a. Cut back and pigtail, or replace all damaged conductors.b. Straighten conductors that remain and remove corrosion and foreign matter.c.Pigtailing existing conductors is permitted, provided the outlet box is large enough.

C. Device Installation:1. Replace devices that have been in temporary use during construction and that were installed before building finishing operations were complete.2. Keep each wiring device in its package or otherwise protected until it is time to connect conductors.3. Do not remove surface protection, such as plastic film and smudge covers, until the last possible moment.4. Connect devices to branch circuits using pigtails that are not less than 6 inches in length.5. When there is a choice, use side wiring with binding-head screw terminals. Wrap solid conductor tightly clockwise, two-thirds to three-fourths of the way

around terminal screw.6. Use a torque screwdriver when a torque is recommended or required by manufacturer.7. When conductors larger than No. 12 AWG are installed on 15- or 20-A circuits, splice No. 12 AWG pigtails for device connections.8. Tighten unused terminal screws on the device.9. When mounting into metal boxes, remove the fiber or plastic washers used to hold device-mounting screws in yokes, allowing metal-to-metal contact.

3.2 FIELD QUALITY CONTROLA.Perform the following tests and inspections:

1. Test Instruments: Use instruments that comply with UL 1436.2. Test Instrument for Convenience Receptacles: Digital wiring analyzer with digital readout or illuminated digital-display indicators of measurement.

B.Tests for Convenience Receptacles:1. Line Voltage: Acceptable range is 105 to 132 V.2. Percent Voltage Drop under 15-A Load: A value of 6 percent or higher is unacceptable.3. Ground Impedance: Values of up to 2 ohms are acceptable.4. Using the test plug, verify that the device and its outlet box are securely mounted.5. Tests shall be diagnostic, indicating damaged conductors, high resistance at the circuit breaker, poor connections, inadequate fault current path, defective

devices, or similar problems. Correct circuit conditions, remove malfunctioning units and replace with new ones, and retest as specified above.C. Wiring device will be considered defective if it does not pass tests and inspections.


No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:56

:3 4 P

M

EG002

ELECTRICALSPECIFICATIONS

NGZ

SAE

2


2 ADDENDUM 1 10-23-15

P

E

AV

PJ

E

AV

J

J

J

AV

P

JJJAV

AV

P

J

P

J

S S

S S

S S

E

E

T

E

E

E

146

144

140

141

143

142

151D

132

133

134

151C

131

130

152A128126

127129

151B

119

118

117

CLASSROOM

121

120 122

116

151A

151E

108

109

109A 109B

110 110A

110B151F

103104

102

101A105

106101

114

151

124

125A

TV

+84"

TV

1

2

+102"

TV

1

2

+36"

+36"

+36"

+48"

+84"

2

TV

2

+78"

+84"

+72"

TV

3

3

3

3

1

1 1

1

2 22

1

3

2

12

2

1

139ACLASSROOM

139BCLASSROOM

135CLASSROOM

111CLASSROOM

4

6

7

1

8

LP3-20

LP3-20

LP3-20 LP3-20

LP3-26LP3-26

LP3-26

LP3-26

LP3-26

LP3-26

LP3-20 LP3-36 LP3-38

LP3-40

9

LP2

LP5LP3

LP3ALP1

SWBD

LP3-27

LP3-27

LP3-23LP3-23

LP3-23

LP3-25

LP3-23

LP3-25

LP3-25

LP3-25

LP3-25

LP3-25

LP3-23

LP3-25

LP4-1LP4-11

LP4-1 LP4-3 LP4-3 LP4-3

LP4-5 LP4-5 LP4-5

LP4-7 LP4-7 LP4-7 LP4-9

LP4-11 LP4-9 LP4-9

LP4-2LP4-2LP4-11LP4-11

LP4-4 LP4-4LP4-2

LP4-6LP4-6LP4-6LP4-4

LP4-8 LP4-8

LP3-23LP2-37LP2-37

LP2-37

LP2-37

LP2-39

LP2-39

LP2-39LP2-39

LP2-39

LP4-17

LP4-14

LP4-14

LP4-14

LP4-17

LP4-17

LP4-14

LP4-17

LP4-14

TV

5

LP4

149CLASSROOM

150CLASSROOM

148CLASSROOM

136COMMROOM

137ELECTRICAL

138ELECTRICAL

E

E

EE

E

E

E

EE

EEE

E

E E

E EE

102

112

12

2

E

E

E E

E

E

E E

2

2

2

2

22

2

2

2 2

2

2

222

2

E2

2

2

2

22

2

EE

E

EE

LP3-36

2

2

2 2

LINE WEIGHT LEGEND


SCREENED LINES INDICATE EXISTING EQUIPMENT TO REMAIN.

SOLID LINES INDICATE EQUIPMENT PROVIDED UNDER THIS CONTRACT.



2

2

2

No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:55

:5 0 P

M

B1-ED101

BUILDING 1ELECTRICALDEMOLITION PLAN

NGZ

SAE

1 REMOVE EXISTING ELECTRICAL CONNECTION TO CEILINGMOUNTED PROJECTOR.

2 REMOVE EXISITING SURFACE MOUNTED A/V BOX ANDASSOCIATED SURFACE MOUNTED RACEWAY SYSTEM.

3 REMOVE EXISITING SURFACE MOUNTED DATA OUTLETAND ASSOCIATED SURFACE MOUNTED RACEWAY SYSTEMTO ABOVE ACCESSIBLE CEILING.

4 ALL DEVICES SHOWN ON THE TWO SIDES OF THIS WALLARE EXISTING TO BE REMOVED UNLESS NOTED OTHERWISE.

5 ALL EQUIPMENT LOCATED IN THE ELECTRICAL ROOM ISEXISTING TO REMAIN.

6 REMOVE EXISTING JUNCTION BOX WITH BLANKFACEPLATE. TYPICAL FOR ALL.

7 REMOVE EXITING COMBINATION RECEPTACLE/TV OUTLET.TYPICAL FOR ALL.

8 EXISTING FIRE ALARM DEVICE TO BE RELOCATED.EXTEND EXISTING CONDUIT AND WIRING TO NEWLOCATION AS INDICATED ON B1-EP101. NEW CONDUITAND WIRING SHALL MATCH EXISTING.

9 REMOVE EXISTING FLOOR BOX. REMOVAL SHALL INCLUDEREMOVING DEVICES AND ASSOCIATED WIRING, ABANDONBOX IN PLACE AND FILL WITH CONCRETE TO MATCHSURROUNDING FLOOR ELEVATION. PROVIDE SMOOTHTROWEL FINISH TO MATCH EXISTING SLAB.

10 EXISTING CEILING MOUNTED SPEAKER TO REMAIN.TYPICAL FOR ALL.

11 ELECTRICAL CONNECTION TO EXISTING CEILINGMOUNTED PROJECTOR TO REMAIN.

12 EXISTING FIRE ALARM DEVICES TO REMAIN. TYPICAL FORALL.

A. RE-USE OF EXISTING CONDUIT IS ALLOWED WHEREPOSSIBLE. CONDUIT SHALL BE INSPECTED TO ENSURE IS INGOOD CONDITION AND IS OF ADEQUATE SIZE PER NECWHERE CONDUIT IS BEING RE-USED FOR BRANCH CIRCUITS.DEMOLITION DRAWINGS REPRESENT GENERAL ITEMS, SIZES,QUANTITIES AND LAYOUT OF ITEMS TO BE REMOVED.VERIFY ACTUAL CONDITIONS AND COMPOSITION OF WORKTO BE PROVIDED.

B. MAINTAIN ELECTRICAL SYSTEMS LOCATED IN ADJACENTAREAS WHICH REMAIN. PROVIDE TEMPORARY POWERWHERE NECESSARY AS DEMOLITION WORK IS PERFORMED.PROVIDE NEW CONDUIT AND WIRING AS NECESSARY TOMAINTAIN INTEGRITY OF EXISTING ELECTRICAL SYSTEMSREMAINING.

C. UNLESS SPECIFICALLY NOTED OTHERWISE, REMOVE ALLINDICATED ELECTRICAL DEVICES AND EXISTING ELECTRICALSYSTEMS LOCATED IN THE WALLS, CASEWORK AND CEILINGSSCHEDULED FOR DEMOLITION. FOR BRANCH CIRCUITS TOBE RE-USED, REMOVE ASSOCIATED BOXES, CONDUIT,CONDUCTORS, OR MC CABLE BACK TO NEAREST JUNCTIONBOX NOT AFFECTED BY DEMOLITION WORK. WHERE BRANCHCIRCUITS ARE NOT RE-USED, REMOVE ALL ASSOCIATEDBOXES, CONDUIT, CONDUCTORS OR MC CABLE, BACK TOPANELBOARD. CONDUIT WHICH PASSES THROUGH EXISTINGAREAS TO REMAIN, MAY BE ABANDONED IN PLACE. REFER TOARCHITECTURAL DEMOLITION PLANS FOR EXTENT OFDEMOLITION.

D. FOR REMOVED VOICE AND DATA OUTLETS, REMOVE CABLESFROM THE OUTLET BACK TO THE PATCH PANEL FROM WHICHITS SERVED. DO NOT ABANDON CABLE IN PLACE. REMOVEALL SURFACE MOUNTED RACEWAY. COORDINATE THEREMOVAL OF DATA CABLES WITH THE OWNER.

E. REMOVE POWER TO ALL WALL CLOCKS AND PATCH EXISTINGWALL.

2

2


2 ADDENDUM 1 10-23-15

146

144

140

141

143

142

151D

139ACLASSROOM

139BCLASSROOM

136COMMROOM

137

138

135CLASSROOM

132

133

134

151C

131

130

152A128126

127129

151B

119

118

117

CLASSROOM

121

120 122

116

151A

151E

108

109

109A 109B

110 110A

110B151F

103104

102

101A105

106101

114

151

124

125A

2

3

1

1

111CLASSROOM

1

149CLASSROOM

150CLASSROOM

148CLASSROOM

1

1

2

2

2 2

2

1

2

1

2

1

2

12

No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:55

:5 2 P

M

B1-ED201

BUILDING 1LIGHTINGDEMOLITION PLAN

NGZ

SAE

1 REMOVE EXISTING LIGHT FIXTURES AND ASSOCIATEDCONTROLS FROM THIS ROOM. REMOVE BRANCH CIRCUITCONDUIT AND WIRING BACK TO THE NEAREST JUNCTIONBOX. MAINTAIN CIRCUITS SERVING AREAS THAT REMAIN.

2 REMOVE EXISTING LIGHT SWITCH. TYPICAL FOR ALLLIGHT SWITCHES SHOWN ON THIS PLAN.

3 REMOVE EXISTING OCCUPANCY SENSOR. TYPICAL FORALL LIGHT OCCUPANCY SENSORS SHOWN ON THIS PLAN.

A. RE-USE OF EXISTING CONDUIT IS ALLOWED WHEREPOSSIBLE. CONDUIT SHALL BE INSPECTED TO ENSURE IS INGOOD CONDITION AND IS OF ADEQUATE SIZE PER NECWHERE CONDUIT IS BEING RE-USED FOR BRANCH CIRCUITS.

B. DEMOLITION DRAWINGS REPRESENT GENERAL ITEMS, SIZES,QUANTITIES AND LAYOUT OF ITEMS TO BE REMOVED. VERIFYACTUAL CONDITIONS AND COMPOSITION OF WORK TO BEPROVIDED.

C. MAINTAIN ELECTRICAL SYSTEMS LOCATED IN ADJACENTAREAS WHICH REMAIN. PROVIDE TEMPORARY POWERWHERE NECESSARY AS DEMOLITION WORK IS PERFORMED.PROVIDE NEW CONDUIT AND WIRING AS NECESSARY TOMAINTAIN INTEGRITY OF EXISTING ELECTRICAL SYSTEMSREMAINING.

D. UNLESS SPECIFICALLY NOTED OTHERWISE, REMOVE ALLINDICATED ELECTRICAL DEVICES AND EXISTING ELECTRICALSYSTEMS LOCATED IN THE WALLS, CASEWORK AND CEILINGSSCHEDULED FOR DEMOLITION. FOR BRANCH CIRCUITS TO BERE-USED, REMOVE ASSOCIATED BOXES, CONDUIT,CONDUCTORS, OR MC CABLE BACK TO NEAREST JUNCTIONBOX NOT AFFECTED BY DEMOLITION WORK. WHERE BRANCHCIRCUITS ARE NOT RE-USED, REMOVE ALL ASSOCIATEDBOXES, CONDUIT, CONDUCTORS OR MC CABLE, BACK TOPANELBOARD. CONDUIT WHICH PASSES THROUGH EXISTINGAREAS TO REMAIN, MAY BE ABANDONED IN PLACE. REFERTO ARCHITECTURAL DEMOLITION PLANS FOR EXTENT OFDEMOLITION.

E. ELECTRICAL CONTRACTOR IS RESPONSIBLE FOR DISPOSALOF ALL REMOVED LUMINARES AND LUMINARE PARTS PERLOCAL, STATE, AND FEDERAL REGULATIONS.

2


2 ADDENDUM 1 10-23-15

PP

P

J

P

S S

S S

S S

AV AVAV

TSJ

J

J

T

E

E

AVAV

AVTS

AV AVAV

TS

AV AVAV

TSJ

E

146CLASSROOM

1088144

1084140

1085141

1086143

1087142

1094151D

139ACLASSROOM

139BCLASSROOM

136COMMROOM135

CLASSROOM

1077132

1076133

1075134

1095151C

1072131

1073130

1071152A1074

1281068126

1069127

1070129

1096151B

1061119

1060118

1059117

123CLASSROOM

1063121

1062120

1064122

1058116

1098151A

1093151E

1048108

1049109

1050109A

1065109B

1051110

1052110A

1053110B1099

151F

10441031045

104

1043102

1042101A 1046

105

10471061041

101

1057114

1097151

1066124

1067125A

1

2 LP3- 26

LP3- 26

LP3-20LP3-20

LP3-20

LP3-20

3

4

LP3- 26

5

LP3-36 LP3- 38

LP3- 38

LP5LP2

LP1

SWBD

LP3ALP3

LP3- 23

LP3- 25

LP3- 23

LP3-27

LP3- 23

LP3-27

LP3- 23LP3- 23

LP3- 25LP2-39

LP2-37

LP2-37

LP3-25

LP3-25

LP3-25

LP3-25

LP2-39

LP2-39

34

5 LP2-37

3

4

5

111CLASSROOM

6

L

UU

LP3- 36

LP3- 36 LP3- 36

LP3- 36

LP4- 2

LP4- 2

LP4- 2

LP4- 2LP4- 3

LP4- 3

LP4- 3

LP4- 3

LP4- 1

LP4- 1

LP4- 1 LP4- 1

LP4- 7 LP4- 7 LP4- 7

LP4- 7LP4- 7

1

1

148CLASSROOM

150CLASSROOM

149CLASSROOM

EXISTING LIGHTING CONTACTOR

LP47

8

2 2 2 2 2 2

138ELECTRICAL

137ELECTRICAL

1

LP4-

4

LP4-

4

LP4-

5

LP4-

6

LP4-

6

LP4-

9

FP4-6LP6-6

FP4-7LP6-7

LP3- 38

1

2

LP3- 42

LU

U1

2

L

UU 1

LP4- 14

LP4- 14

2LP3- 40

L

U U 1

34

5

LP3- 11

9

3

3

3

3

102

102

102

102

62

E

E

EEE

E

E

E

E

E

E

E

E

E E

E

E

E E

EE E

E

2

2

2

2

2

2

2

2 2

2E2 2

2

22

2

222

2E

E E

2

2

EE

E

E

2

2

2

2

E2

EE

2

E

EE

E

E

1EE

EE2

2 2 2

2

22

1

E2

2

E

E

2

2

2 2 2 2 2 2

3LP4-9

2

LINE WEIGHT LEGEND


SCREENED LINES INDICATE EXISTING EQUIPMENT.

SOLID LINES INDICATE EQUIPMENT PROVIDED ON THIS CONTRACT.



2

No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:56

:1 7 P

M

B1-EP101

BUILDING 1POWER ANDSYSTEMS PLAN

NGZ

SAE

1 RELOCATED FIRE ALARM DEVICE.2 RECEPTACLES, DATA OUTLET, AND A/V DEVICE BEHIND

MILLWORK. SEE MILLWORK ELEVATION 11/B1-AE201 FOREXACT MOUNTING HEIGHT AND LOCATION OF DEVICESPRIOR TO ROUGH-IN.

3 BACK BOX FOR WALL MOUNTED PROJECTOR SIGNALCABLES. 4" SQUARE X 2 1/8" DEEP BOX WITH STAINLESSSTEEL COVER. CONCEAL BEHIND PROJECTOR WALLPLATE. PROVIDE 1 1/2" DIAMETER OPENING WITHGROMMET IN THE CENTER OF THE COVER PLATE. SEESHEET B1-AE201 FOR INTERIOR WALL ELEVATIONS.COORDINATE EXACT MOUNTING REQUIREMENTS WITH THEOWNER AND PROJECTOR BEING FURNISHED.

4 1 1/4" CONDUIT TO CLASSROOM ACCESSIBLE CEILINGSPACE. TERMINATE CONDUIT 6" ABOVE ACCESSIBLECEILING. PROVIDE INSULATED BUSHING AT TERMINATIONABOVE CEILING.

5 RECEPTACLE FOR WALL MOUNTED PROJECTOR.CONCEAL BEHIND PROJECTOR WALL PLATE. SEE SHEETB1-AE201 FOR INTERIOR WALL ELEVATIONS. COORDINATEEXACT MOUNTING REQUIREMENTS WITH THE OWNER ANDPROJECTOR BEING FURNISHED.

6 PROVIDE FIRE ALARM AUDIO/VISUAL NOTIFICATIONAPPLIANCE TO MATCH EXISTING. DEVICE SHALL BE ULLISTED FOR USE WITH THE EXISTING SYSTEM. CONNECTTO THE EXISTING NOTIFICATION APPLIANCE CIRCUITSERVING THIS AREA. PROVIDE 3/4" RED CONDUIT WITHFIRE ALARM SYSTEM WIRING AS REQUIRED.

7 EXISTING 30KVA ISOLATION TRANSFORMER TO REMAIN.8 REMOVE DATA RACK. COORDINATE REMOVAL WITH

OWNER.9 EXISTING ELECTRICAL CONNECTION TO EXISTING CEILING

MOUNTED PROJECTOR. RE-DIRECT CEILING MOUNTEDPROJECTOR TO NEW TEACHING WALL LOCATION ON WESTWALL OF THIS ROOM.

10 PROVIDE 1 1/4" CONDUIT BETWEEN THE UPPER ANDLOWER AV BOXES, REFER TO 11/B1-AE201 FOR DETAIL.

A. TELEPHONE/DATA SYSTEM CONSISTS OF CONDUIT,BACKBOX, JACKS AND FACEPLATE. SEE TELEPHONE/DATASYSTEM LEGEND ON SHEET EG001 AND TYPICALVOICE/DATA OUTLET DETAIL 1/EG001 FOR ADDITIONALINFORMATION.

FIRE ALARM SYSTEM NOTES:

A. ALL NEW FIRE ALARM DEVICES SHALL BE UL LISTES.B. PROVIDE PROGRAMMING MODIFICATIONS AS

REQUIRED TO SUPPORT NEW DEVICES ADDED TO THEEXISTING SYSTEM.

C. VERIFY THAT THE EXISTING POWER SUPPLIES ANDBATTERIES ARE ADEQUATE TO SERVE NEWNOTIFICATION APPLIANCES PROVIDED UNDER THISPROJECT.

D. PERSONNEL SHALL BE TRAINED AND CERTIFIED BYMANUFACTURER FOR INSTALLATION OF UNITSREQUIRED FOR THIS PROJECT.

E. DO NOT INTERRUPT FIRE ALARM SERVICE TO THEBUILDING AT ANY TIME.

F. COMPLY WITH NFPA 72, NFPA 101, AND REQUIREMENTSOF AUTHORITIES HAVING JURISDICTION FORINSTALLATION AND TESTING OF FIRE ALARMEQUIPMENT. INSTALL ALL ELECTRICAL WIRING TOCOMPLY WITH REQUIREMENTS IN NFPA 70 INCLUDING,BUT NOT LIMITED TO, ARTICLE 760, "FIRE ALARMSYSTEMS".

G. FIELD TESTS SHALL BE WITNESSED BY THEAUTHORITIES HAVING JUSRISDICTION.

H. ENGAGE A FACTORY AUTHORIZED SERVICEREPRESENTATIVE TO TEST AND INSPECTCOMPONENTS, ASSEMBLIES, AND EQUIPMENTINSTALLATIONS, INCLUDING CONNECTIONS.

I. COMPLY WITH THE "TEST METHODS" TABLE IN THE"TESTING" SECTION OF THE "INSPECTION, TESTINGAND MAINTENANCE" CHAPTER IN NFPA 72.

2

2

2

2

2


2 ADDENDUM 1 10-23-15

2

RC

RCRC

RC

RC

RC

RC

CLASSROOM

144

140

141

143

142

151D

139ACLASSROOM

136COMMROOM

137

138

132

133

134

151C

131

130

152A128126

127129

151B

119

118

117

121

120 122

116

151A

151E

108

109

109A 109B

110 110A

110B151F

103104

102

101A105

106101

114

151

124

125A

B1

B1B1B

B1

B1

B1B

B1

B1

B1

B1

B1

B1

B1B

B1B

B1

B1

B1

B1

B1

B1

B1

B1B

B1B

B1

B1

B1

B1B B1 B1 B1

B1

B1

B1

B1

B1B

B1

B1

B1

B1 B1 B1 B1

B1B B1

B1 B1

B1

B1

B1

B1 B1 B1

B1B B1 B1B

B1 B1 B1

B1

B1

B1

a a a

b b b

b b b b

b

b

a a

b

b b

b

a a

b

b

a a a a

bbb

b b b

a b

a b

b/D a/D

Da,b

2

a/D

Da

2

a b

b/D

Db

2

a a

a

a a

a

a a b

b

b b

b

b b

b

b

a,b a,b

a,b

a,b

a,ba,b

a/Db/D

Da,b2

a/D b/D

Da,b2

a/D

b/DDa,b

2

a,b

LP1-10

1 1

LP1-26

LP1-28

1

1

1

P/1-9

1a

b

111CLASSROOM

139BCLASSROOM

135CLASSROOM

LP1-10

B1

B1

B1B

a a b b

bbaaa

Dc

2

b

B1BB1

a b

150CLASSROOM

149CLASSROOM

148CLASSROOM

b

b

b

2

2

B1B b

B1

a

B1

b

B1b

No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:56

:0 5 P

M

B1-EL101

BUILDING 1LIGHTING PLAN

NGZ

SAE

1 CONNECT NEW LIGHT FIXTURES TO EXISTING LIGHTINGCIRCUIT THAT PREVIOUSLY SERVED THIS ROOM.

2 MOUNT TO JUNCTION BOX PER MANUFACTURERSRECOMENDATIONS. ALL JUNCTION BOXES SHALL BELOCATED IN AN ACCESSIBLE LOCATION ABOVEACCESSIBLE CEILING. LABEL EACH JUNCTION BOX TOINDICATE ITS FUNCTION. PROVIDE IDENTIFICATION PLATEON THE CEILING SYSTEM T-FRAME INDICATING LOCATIONOF JUNCTION BOXES ABOVE.

A. PROVIDE UNSWITCHED PHASE CONDUCTOR FORBRANCH CIRCUITS SERVING EXIT SIGNS ANDFIXTURES WITH EMERGENCY BATTERY BACK UP.UNSWITCHED PHASE CONDUCTOR SHALL BE AHEADOF ANY CONTACTS OR ANY DEVICE CONTROLLINGFIXTURES.


1 PENDING YYYY-MM-DD2 ADDENDUM 1 10-23-15

AV

S SS

S S S

SSS

S S S

SSS

S S S

SS S

E

MDE

E E

MD MD

E

E

DC

MD

E

MD

DC

DC

TT

AV

E

AV

E

E

E

MD

E

E

E

E

E

104COMPUTER

LAB

117

120

ELECTRICAL

103COMPUTER

LAB

101COMPUTER

LAB

110 111 OFFICE OFFICE

100

W

M

151

149A

149

146A

147A

142141139

140

145

143

144 148A

153

152

108

129 128 127 126

107106

125 124

132 131

130A

130

105

119

134

137

133

136

150

PS

MC

VAV-10

OC OC

PSMC PSMC

EDH

VAV

OC

OC

OC

PS

MC

MC

MC

A

MSB/A

TA

TB

B

P/AP/MP/H

2

SEC FACP

3

TV TV

3

3

OC

PSMC TV

3

1

101COMPUTER

LAB102

COMPUTERLAB

103COMPUTER

LAB

114OFFICE

115OFFICE

116LOUNGE

??

4

4 4

5

6

6

6

6

7

7

13

7

B-6

B-6

B-6

B-6

B-6

B-8

B-8 B-8

B-4B-4B-4

B-4 B-4 B-4B-5

B-2B-2 B-2

B-2B-2B-2

B-6B-14

B-14 B-14

B-22

B-22B-22 B-22

B-12

B-12

B-12

B-12

B-10

B-10

B-10B-10

B-16

B-10

B-10

B-12

B-6

B-14

B-16B-22 B-22

B-18B-18

B-18 B-18

B-18

B-20

B-20B-20

B-20

B-18

B-20

B-26

B-26

B-18

B-24

B-24 B-24

B-24

B-18

B-26

B-26

B-28

B-26

B-26

B-18

B-24

B-24

B-8B-30

B-28

B-28B-28B-29B-28

B-30B-30B-30B-30

B-278 8 8

9 10

11

12

B-39B-39

B-39

B-39

B-35

B-35

B-37

B-35

B-35

B-35

B-37

B-37

B-39

B-39

44

4

OCOC

OCP

PS6

PS

P

6

314

E E E

EEE

E E E

EEE

2 2 2

2 2 2

2 2 2

2 2 2

EE

E

E

E

E

E

E E

2 2

2

2

2

2

2

22

E

2

E2

E 2

E2

E

E

E

E

E

E E

E

E

E

E

2

2

2

2

2 2

2

2

2

2

2

E 2E 2 E

2

E E2 2

E2

E2

E E E E E

E

E

E

EE

E

E

EE

E

E

EE

E

E

EE

E

E

E

2 2

2 2

22

2 2

2 2

2 2 2

2 2 2

2 2 2

2 2 2

2 2 2

E E2

2

E 2E

2

E E2 2 E2 E

2

E EE

2 2

EE

2

E

E

E

E

E

E

E

E

E

E

E

22

2

2

2

2

2

2

2

2

E

E2

2

EEE

E

222

2

E E22

E2

EE2 2

2

E2

E2 E

2

E

E

E

E

E

E

E2

2

2

2

2

2

2

E

E

E

E

E

2

2

2

2

2

E E E

EE

EREE

E E ER

EREE

E ERE

ER

E E

2

22

2 2

2 22

2 2 2

222

2 2 2

22

2

ER2

E2

E

E

2

2

E

2

E2

E2

E2

E2

E

2

E2

E2

E2

E2

E2

E2

3

LINE WEIGHT LEGEND






2

No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:56

:2 1 P

M

B2-ED101

BUILDING 2ELECTRICALDEMOLITION PLAN

NGZ

SAE

1 TYPICAL EXISTING CEILING MOUNTED SPEAKER TO BEREMOVED. SEE B2-EP101 FOR LOCATION.

2 EXISTING TELECOMMUNICATIONS BACKBOARD TOREMAIN.

3 EXISTING ELECTRICAL CONNECTION TO CEILINGMOUNTED PROJECTOR TO REMAIN.

4 REMOVE EXISITING SURFACE MOUNTED A/V BOX ANDSURFACE MOUNTED RACEWAY SYSTEM.

5 TYPICAL EXISTING MOTION DETECTOR TO REMAIN.6 EXISTING ELECTRICAL CONNECTION TO PROJECTION

SCREEN TO REMAIN.7 EXISTING MOMENTARY CONTACT SWITCH TO REMAIN.

MOMENTARY CONTACT SWITCH IS USED FOR CONTROLOF EXISTING PROJECTION SCREEN.

8 REMOVE DUPLEX RECEPTACLE WITH COAXIALCONNECTOR IN DOUBLE GANG BOX AND FACEPLATE.

9 TYPICAL EXISTING DUPLEX RECEPTACLE TO REMAIN.10 TYPICAL EXISTING FIRE ALARM HORN/STROBE TO REMAIN.11 EXISTING TYPICAL VOICE/DATA OUTLET TO REMAIN.12 ALL ELECTRICAL EQUIMENT SHOWN ON THIS ROOM IS

EXISTING TO REMAIN.13 RELOCATE MOMENTARY CONTACT SWITCH. MOMENTARY

CONTACT SWITCH IS USED FOR CONTROL OF EXISTINGPROJECTION SCREEN. SEE SHEET B2-EP101 FOR NEWLOCATION. EXTEND EXISTING CONDUIT AND WIRING TONEW LOCATION.

14 REMOVE EXISTING CEILING MOUNTED RECEPTACLE.

A. RE-USE OF EXISTING CONDUIT IS ALLOWED WHEREPOSSIBLE. CONDUIT SHALL BE INSPECTED TO ENSURE IS INGOOD CONDITION AND IS OF ADEQUATE SIZE PER NECWHERE CONDUIT IS BEING RE-USED FOR BRANCHCIRCUITS. DEMOLITION DRAWINGS REPRESENT GENERALITEMS, SIZES, QUANTITIES AND LAYOUT OF ITEMS TO BEREMOVED. VERIFY ACTUAL CONDITIONS ANDCOMPOSITION OF WORK TO BE PROVIDED.

B. MAINTAIN ELECTRICAL SYSTEMS LOCATED IN ADJACENTAREAS WHICH REMAIN. PROVIDE TEMPORARY POWERWHERE NECESSARY AS DEMOLITION WORK IS PERFORMED.PROVIDE NEW CONDUIT AND WIRING AS NECESSARY TOMAINTAIN INTEGRITY OF EXISTING ELECTRICAL SYSTEMSREMAINING.

C. UNLESS SPECIFICALLY NOTED OTHERWISE, REMOVE ALLINDICATED ELECTRICAL DEVICES AND EXISTINGELECTRICAL SYSTEMS LOCATED IN THE WALLS,CASEWORK AND CEILINGS SCHEDULED FOR DEMOLITION.FOR BRANCH CIRCUITS TO BE RE-USED, REMOVEASSOCIATED BOXES, CONDUIT, CONDUCTORS, OR MCCABLE BACK TO NEAREST JUNCTION BOX NOT AFFECTEDBY DEMOLITION WORK. WHERE BRANCH CIRCUITS ARE NOTRE-USED, REMOVE ALL ASSOCIATED BOXES, CONDUIT,CONDUCTORS OR MC CABLE, BACK TO PANELBOARD.CONDUIT WHICH PASSES THROUGH EXISTING AREAS TOREMAIN, MAY BE ABANDONED IN PLACE. REFER TOARCHITECTURAL DEMOLITION PLANS FOR EXTENT OFDEMOLITION.

D. FOR REMOVED VOICE AND DATA OUTLETS, REMOVECABLES FROM THE OUTLET BACK TO THE PATCH PANELFROM WHICH ITS SERVED. DO NOT ABANDON CABLE INPLACE. REMOVE ALL SURFACE MOUNTED RACEWAY.COORDINATE THE REMOVAL OF DATA CABLES WITH THEOWNER.

E. REMOVE POWER TO ALL WALL CLOCKS AND PATCHEXISTING WALL.

2

2

2

2


2 ADDENDUM 1 10-23-15

116TUTORINGCENTER

115OFFICE

114OFFICE

104COMPUTER

LAB117

120

ELECTRICAL

103COMPUTER

LAB

102COMPUTER

LABCOMPUTER

LAB

110 111 OFFICE113

OFFICE

100

W

M

109BMULTI-PURPOSE

ROOM151

149A

149

146A

147A

142141139

140

145

143

144 148A

153

152

108

129 128 127 126

107 106

125 124

132 131

130A

130

105

119

134

137

133

136

150

44

4

33

33

33

1

2

32 12

12 12

12

12

12

12

12

12

No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:56

:2 3 P

M

B2-ED201

BUILDING 2LIGHTINGDEMOLITION PLAN

NGZ

SAE

1 REMOVE ALL LIGHT FIXTURES AND ASSOCIATEDCONTROLS FROM THIS ROOM. REMOVE BRANCH CIRCUITCONDUIT AND WIRING TO THE NEAREST JUNCTION BOX.MAINTAIN CIRCUITS SERVING AREAS THAT REMAIN.

2 REMOVE EXISTING LIGHT SWITCH. TYPICAL FOR ALLLIGHT SWITCHES SHOWN ON THIS PLAN.

3 REMOVE EMERGENCY LIGHTING UNIT. TYPICAL FOR ALLEMERGENCY LIGHTING UNITS SHOWN ON THIS PLAN.

A. RE-USE OF EXISTING CONDUIT IS ALLOWED WHERE POSSIBLE.CONDUIT SHALL BE INSPECTED TO ENSURE IS IN GOODCONDITION AND IS OF ADEQUATE SIZE PER NEC WHERECONDUIT IS BEING RE-USED FOR BRANCH CIRCUITS.

B. DEMOLITION DRAWINGS REPRESENT GENERAL ITEMS, SIZES,QUANTITIES AND LAYOUT OF ITEMS TO BE REMOVED. VERIFYACTUAL CONDITIONS AND COMPOSITION OF WORK TO BEPROVIDED.

C. MAINTAIN ELECTRICAL SYSTEMS LOCATED IN ADJACENTAREAS WHICH REMAIN. PROVIDE TEMPORARY POWERWHERE NECESSARY AS DEMOLITION WORK IS PERFORMED.PROVIDE NEW CONDUIT AND WIRING AS NECESSARY TOMAINTAIN INTEGRITY OF EXISTING ELECTRICAL SYSTEMSREMAINING.

D. UNLESS SPECIFICALLY NOTED OTHERWISE, REMOVE ALLINDICATED ELECTRICAL DEVICES AND EXISTING ELECTRICALSYSTEMS LOCATED IN THE WALLS, CASEWORK AND CEILINGSSCHEDULED FOR DEMOLITION. FOR BRANCH CIRCUITS TO BERE-USED, REMOVE ASSOCIATED BOXES, CONDUIT,CONDUCTORS, OR MC CABLE BACK TO NEAREST JUNCTIONBOX NOT AFFECTED BY DEMOLITION WORK. WHERE BRANCHCIRCUITS ARE NOT RE-USED, REMOVE ALL ASSOCIATEDBOXES, CONDUIT, CONDUCTORS OR MC CABLE, BACK TOPANELBOARD. CONDUIT WHICH PASSES THROUGH EXISTINGAREAS TO REMAIN, MAY BE ABANDONED IN PLACE. REFER TOARCHITECTURAL DEMOLITION PLANS FOR EXTENT OFDEMOLITION.

E. ELECTRICAL CONTRACTOR IS RESPONSIBLE FOR DISPOSALOF ALL REMOVED LUMINARES AND LUMINARE PARTS PERLOCAL, STATE, AND FEDERAL REGULATIONS.


2 ADDENDUM 1 10-23-15

S SS

S S

SS

S S

SS

S

SS

E

MDE

E E

MD MD

E

E

DC

MD

E

MD

DC

DC

TT

EE

E

E

MD

E

J

J

S

SS

S

S

S

S

P

P

E

EEEE

E

E

E

E

AV AVAV

TS

AVAVAV

TS

AVAV

AVTS

AV AVAV

TS

116TUTORINGCENTER

115OFFICE

114OFFICE

104COMPUTER

LAB

1107117

1109120

118ELECTRICAL

103COMPUTER

LAB

102COMPUTER

LAB

101COMPUTER

LAB

110110

111111

112OFFICE

113OFFICE

1126100

1133W

1134M

109BMULTI-PURPOSE

ROOM1150151

1132149A

1131149

1123146A

1124147A

1120142

1118141

1114139

1117140

1119145

1121143

1122144

1125148A

1130153

1135152

1136108

1144129

1143128

1142127

1141126

1152107 1145

106

1147125

1148124

1140132

1139131

1137130A

1138130

1146105

1149119

1128134

1129137

1115133

1116136

1127150

PSMC

MC

MC

VAV

E

VAV-10

PS

MC

PSMC

PS

B

P/AP/MP/H

A

TA

MSB/A

TB

3

1

2

4

B-39

B-39

B-39

B-39

B-39

B-37

B-37

B-35 B-35

B-35

B-35

B-35

B-29

B-37

3

1

2

B-37

5

55

5

5

5

6

6

CU-B2.1

FCU-B2.1FCU-B2.2FCU-B2.3FCU-B2.4

A-67,6930 A

30 A30 A

30 A

30 A4X

A-71,73

2#10 + 1#10G1/2"C

B-2 B-2 B-2

B-2B-2B-2

B-4 B-4 B-4

B-4B-4B-4

B-6

B-6

B-6B-8

B-8 B-8

B-6

B-27

B-6 B-6

B-12

B-12

B-12

B-10

B-10

B-10 B-10

B-10

B-10

B-12

B-12

B-5P B-6

P

B-27B-14

B-16 B-16

PH-37

B-20B-20

B-20 B-20

B-18B-18

B-18

B-18 B-18

B-18

B-20

B-22B-22

B-7P

B-22

B-27 B-22 B-22 B-28 B-29 B-28PS

B-28

B-30

B-30B-30B-30B-30

B-26B-26

B-26 B-26

B-18B-18

B-24

B-24 B-24

B-24

B-28

B-8P

B-26

B-26

B-18

B-24

B-24

OCOCOC

OC

5

ADD ALTERNATE #1

MC4 4

4

P

PS

PS

P

7 A- 75

L

U U 1

7

L

UU

1

A- 36

7A- 76

L

U

U

1

7

L

U U 1 MC

8

B-14

3

3

3

3

B-29

B-29

E 2

E2

E E

EEE

EE

E

EEE

2 2

2 2 2

2

2

2

2 2 2

E

E

E

E

E

E E

2

2

2

2

2

22

E

2

E2

E 2

E2

E

E

E

E

E

E E

E

E

E

E

2

2

2

2

2 2

2

2

2

2

2

E 2

E

2

E E

22

E2

B-8

EE E E

E

E

E

E

EE

E

E

EE

E

E

EE

E

E

EE

E

E

E

22

2 2

22

2 2

2 2

2 2

22 2 2

2 2 2

2 2 2

2 2 2

E E2

2

EE

2

E E2 2 E2

E

2

E E E2 2

EE

2

E2

E2

E2

E

EEE

E

222

2

EE

2

2

E2

2

E2

E

E

E

E

E

E

E

E

E

E

2

2

2

2

2

2

2

2

2

2

E

E2

2

E2

EDH

2

E2

E2

E2

E2

E 22

2E

2 ER

ER

E

E

E

E

E

E2

2

2

2

2

2

E

E

E

E

2

2

2

2

E EE

E

E

EE

E E

EE

EE

2

2

2

2

2

2

2 2

22

2 2

E2

E

E

2

2

E2

E2

E2

E2

E2

E2

92

92

E 2

E2

E2

E 2E 2

E 2

92

92

LINE WEIGHT LEGEND






2

No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:56

:2 9 P

M

B2-EP101

BUILDING 2POWER ANDSYSTEMS PLAN

NGZ

SAE

1 1 1/4" CONDUIT TO CLASSROOM ACCESSIBLE CEILINGSPACE. PROVIDE INSULATED BUSHING AT TERMINATIONABOVE CEILING.

2 RECEPTACLE FOR WALL MOUNTED PROJECTOR.CONCEAL BEHIND PROJECTOR WALL PLATE. COORDINATEEXACT REQUIREMENTS WITH THE ACTUAL PROJECTORBEING FURNISHED.

3 BACK BOX FOR WALL MOUNTED PROJECTOR SIGNALCABLES. 4" SQUARE X 2 1/8" DEEP BOX WITH STAINLESSSTEEL COVER. CONCEAL BEHIND PROJECTOR WALLPLATE, COORDINATE EXACT REQUIREMENTS WITH THEACTUAL PROJECTOR BEING FURNISHED. PROVIDE 1 1/2"DIAMETER OPENING WITH GROMMET IN THE CENTER OFTHE COVER PLATE.

4 EXISTING SOUND EQUIPMENT CABINET.5 EXISTING RELOCATED SPEAKER.6 PROVIDE FIRE ALARM PULL STATION TO MATCH EXISTING.

DEVICE SHALL BE UL LISTED FOR USE WITH THE EXISTINGSYSTEM. CONNECT TO THE EXISTING SIGNALING LINECIRCUIT SERVING THIS AREA. PROVIDE 3/4" RED CONDUITWITH FIRE ALARM SYSTEM WIRING AS REQUIRED.

7 RECEPTACLES, DATA OUTLET, AND A/V DEVICE BEHINDMILLWORK. SEE MILLWORK ELEVATION 11/B1-AE201 FOREXACT MOUNTING HEIGHT AND LOCATION OF DEVICESPRIOR TO ROUGH-IN.

8 RELOCATED MOMENTARY CONTACT SWITCH FORCONTROL OF PROJECTION SCREEN. PROVIDE NEWCONDUIT AND CONTROL WIRING AS REQUIRED.

9 PROVIDE 1 1/4" CONDUIT BETWEEN THE UPPER ANDLOWER AV BOXES, REFER TO 11/B1-AE201 FOR DETAIL.

A. TELEPHONE/DATA SYSTEM CONSISTS OF CONDUIT,BACKBOX, JACKS AND FACEPLATE. SEE TELEPHONE/DATASYSTEM LEGEND ON SHEET EG001 AND TYPICALVOICE/DATA OUTLET DETAIL 1/EG001 FOR ADDITIONALINFORMATION.

2

2

2

2

FIRE ALARM SYSTEM NOTES:

A. ALL NEW FIRE ALARM DEVICES SHALL BE UL LISTES.B. PROVIDE PROGRAMMING MODIFICATIONS AS

REQUIRED TO SUPPORT NEW DEVICES ADDED TO THEEXISTING SYSTEM.

C. VERIFY THAT THE EXISTING POWER SUPPLIES ANDBATTERIES ARE ADEQUATE TO SERVE NEWNOTIFICATION APPLIANCES PROVIDED UNDER THISPROJECT.

D. PERSONNEL SHALL BE TRAINED AND CERTIFIED BYMANUFACTURER FOR INSTALLATION OF UNITSREQUIRED FOR THIS PROJECT.

E. DO NOT INTERRUPT FIRE ALARM SERVICE TO THEBUILDING AT ANY TIME.

F. COMPLY WITH NFPA 72, NFPA 101, AND REQUIREMENTSOF AUTHORITIES HAVING JURISDICTION FORINSTALLATION AND TESTING OF FIRE ALARMEQUIPMENT. INSTALL ALL ELECTRICAL WIRING TOCOMPLY WITH REQUIREMENTS IN NFPA 70 INCLUDING,BUT NOT LIMITED TO, ARTICLE 760, "FIRE ALARMSYSTEMS".

G. FIELD TESTS SHALL BE WITNESSED BY THEAUTHORITIES HAVING JUSRISDICTION.

H. ENGAGE A FACTORY AUTHORIZED SERVICEREPRESENTATIVE TO TEST AND INSPECTCOMPONENTS, ASSEMBLIES, AND EQUIPMENTINSTALLATIONS, INCLUDING CONNECTIONS.

I. COMPLY WITH THE "TEST METHODS" TABLE IN THE"TESTING" SECTION OF THE "INSPECTION, TESTINGAND MAINTENANCE" CHAPTER IN NFPA 72.

2


2 ADDENDUM 1 10-23-15

RC RC RC

RC

RC

116TUTORINGCENTER

115OFFICE

114OFFICE

117

120

ELECTRICAL

103COMPUTER

LAB102

COMPUTERLAB

101COMPUTER

LAB

110 111 OFFICE

113OFFICE

100

W

M

109BMULTI-PURPOSE

ROOM

151

149A

149

146A

147A

142141139

140

145

143

144 148A

153

152

108

129 128 127 126

107

106

125 124

132 131

130A

130

105119

134

137

133

136

150

a a

aa

B1 B1

B1B1B

a

a a

aa

a a

aa

B1 B1

B1B1

B1 B1

B1B1

a

a

P/B-5

P/B-5

P/B-5

1

1

1

aB1 B1

a a

a/D

P/A-1

B1 B1B B1 B1 B1B B1 B1 B1B B1

B1 B1 B1 B1 B1 B1 B1 B1 B1


B1 B1 B1 B1 B1 B1 B1 B1


B1B B1BB1B

B1 B1 B1B

B1B B1 B1 B1

B1 B1 B1 B1

B1 B1 B1B B1

B1B B1 B1 B1

B1 B1 B1 B1

B1 B1 B1B

B1B

B1B

B1

B1B

B1

B1B

B1

B1B

B1

B1

B1

B1

B1

B1

B1

B1B

B1

B1B

B1

B1B

B1

B1

B1

B1

B1

B1

B1B

a a a

aaa

a a a

aaa

a a a

a

a

a

a

a a

a

a

a

a

a

a

a

a

a a

a

a

a

a a

a

a

a

a

a

a

a

a

a

a a

a

a

a

a

a a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

aa a/D

a

a

1P/A-1

1

Da

2

a a a a

a a a a

b b bb

b b b b

c cc

c

c c c c

d

c c c

a/D

1

1

P/A-511

1 P/B-3

a

Da

2

a/D

Da

2

a

a

a

a

a

a

a,b,c

a a

c

P/A-3 P/A-3 P/A-3

P/A-3P/A-3P/A-3

P/A-3 P/A-3 P/A-3

P/A-3P/A-3P/A-3

P/A-3 P/A-3 P/A-3

P/A-5 P/A-5 P/A-5 P/A-5

P/A-5P/A-5P/A-5P/A-5

P/A-5 P/A-5 P/A-5 P/A-5


P/A-5 P/A-5 P/A-5 P/A-5

P/A-5P/A-5P/A-5

P/A-5P/A-3

a

a

P/A-7 P/A-7 P/A-7

P/A-7 P/A-7 P/A-7 P/A-7

P/A-7 P/A-7 P/A-7

P/A-7

P/A-7 P/A-7 P/A-7 P/A-7


P/A-9 P/A-9 P/A-9 P/A-9

P/A-9 P/A-9

P/A-9

P/A-9

c

c/D

Da,b

3

B1 B1 B1 B1

c c c cP/A-9P/A-9P/A-9P/A-9

P/A-7 P/A-7 P/A-7 P/A-7

B1 B1 B1 B1

a a a a

cc

bb

a/D

4

4

4

2

2

b/D2

D

c

3

No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

0 5'


10' 20' 30'

N

KEY NOTES :

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:56

:2 6 P

M

B2-EL101

BUILDING 2LIGHTING PLAN

NGZ

SAE

1 CONNECT NEW LIGHT FIXTURES TO EXISTING LIGHTINGCIRCUIT THAT PREVIOUSLY SERVED THIS ROOM.

2 MOUNT TO JUNCTION BOX PER MANUFACTURERSRECOMENDATIONS. ALL JUNCTION BOXES SHALL BELOCATED IN AN ACCESSIBLE LOCATION ABOVEACCESSIBLE CEILING. LABEL EACH JUNCTION BOX TOINDICATE ITS FUNCTION. PROVIDE IDENTIFICATION PLATEON THE CEILING SYSTEM T-FRAME INDICATING LOCATIONOF JUNCTION BOXES ABOVE.

3 ROOM CONTROLLER. PROVIDE WATTSTOPPER LMRC 213.MOUNT TO JUNCTION BOX PER MANUFACTURERSRECOMENDATIONS. ALL JUNCTION BOXES SHALL BELOCATED IN AN ACCESSIBLE LOCATION ABOVEACCESSIBLE CEILING. LABEL EACH JUNCTION BOX TOINDICATE ITS FUNCTION. PROVIDE IDENTIFICATION PLATEON THE CEILING SYSTEM T-FRAME INDICATING LOCATIONOF JUNCTION BOXES ABOVE.

4 PROVIDE ILLUMINATED EXIT SIGN TO MATCH EXISTINGEXITS SIGNS IN ROOM. PROVIDE BATTERY BACK-UPPOWER TO ILLUMINATE SIGN FOR A MINIMUM OF 90MINUTES. CONNECT TO EXISTING BRANCH CIRCUITSERVING EXIT SIGNS IN ROOOM.

A. PROVIDE UNSWITCHED PHASE CONDUCTOR FORBRANCH CIRCUITS SERVING EXIT SIGNS ANDFIXTURES WITH EMERGENCY BATTERY BACK UP.UNSWITCHED PHASE CONDUCTOR SHALL BE AHEADOF ANY CONTACTS OR ANY DEVICE CONTROLLINGFIXTURES.


1 PENDING YYYY-MM-DD2 ADDENDUM 1 10-23-15

LINENEUTRAL

TWO RELAYDIGITAL ROOMCONTROLLER

EQUIVALENTPLAN SYMBOL

TYPICAL 0-10V DIMMABLEDRIVER

277VNORMALLIGHTINGCIRCUIT

SWITCH LEG "a"a,b

SWITCH LEG "b"

LIGHTINGFIXTURES

LIGHTINGFIXTURES

RC

DIGITAL OCCUPANCY SENSOR; SEEPLANS FOR LOCATION. DAISY-CHAIN

ADDITIONAL SENSORS AS INDICATEDON PLANS.

NETWORK CABLE

EQUIVALENT PLANSYMBOL

NEUTRAL

a,b

RJ45CONNECTOR

(TYPICAL)

JUNCTION BOX WITH BLANKCOVER MOUNTED ABOVECEILING. SIZE ASREQUIRED.(TYPICAL)

NOTES: (DETAIL 1/EL601)A. ALL LINE VOLTAGE WIRING SHALL BE #12AWG AND ENCLOSED IN 1/2" CONDUIT.B. NETWORK CABLE SHALL BE IN ACCORDANCE WITH MANUFACTURERS REQUIREMENTS. THE

NETWORK CABLE SHALL BE FREE-WIRED ABOVE THE FINISHED CEILING, ROUTEDPARALLEL AND PERPENDICULAR TO STRUCTURAL ELEMENTS. CABLE SHALL BE FASTENEDTO THE STRUCTURE WITH APPROPRIATE CABLE TIES AT 3'-0" INTERVALS. DO NOT FASTENCABLE TO OTHER CONDUIT SYSTEMS.

C. ALL LOW VOLTAGE, CLASS 2 WIRING SHALL BE PER MANUFACTURER'S SPECIFICATIONSAND ENCLOSED IN 1/2" CONDUIT.

D. PROVIDE COVERS AND IDENTIFY JUNCTION BOXES PER SPECIFICATIONS.E. PROVIDE IDENTIFICATION PLATE ON THE CEILING GRID INDICATING LOCATION OF DIGITAL

ROOM CONTROLLER.F. SETTINGS OF OCCUPANCY SENSOR(S): MANUAL ON, AUTO OFF, MANUAL OVERRIDE.

OCCUPANCY SENSOR OPERATION DESCRIPTION

UNDER NORMAL OPERATING CONDITIONS, THIS SYSTEM SHALL TURN ON VIA THE MANUAL LOWVOLTAGE WALL SWITCHES. THE SYSTEM SHALL PROVIDE OCCUPANCY SENSING OF PERSONNELAND AUTOMATICALLY TURN OFF LIGHTING FIXTURES CONTROLLED BY THE ROOM CONTROLLERWHEN ROOM IS UNOCCUPIED.

a

b

a

EQUIVALENT PLANSYMBOL. TYICAL

TO ADDITIONALSWITCHES. SEE PLANS

FOR QUANTITIES

b

a,b

TO ADDITIONALSENSORS. SEE PLANS

FOR QUANTITIES

NEUTRAL

NEUTRALLINE

SWITCH LEG "a"

SWITCH LEG "b"

CLASS 2, 0-10VCONTROL WIRING

D

DD

No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:56

:3 5 P

M

EL601

LIGHTINGCONTROLSDIAGRAMS

NGZ

SAE

SCALE: NOT TO SCALETYPICAL LIGHTING CONTROLS WIRING DIAGRAM1


3P125 A

800A, 3ø, 4W, 480Y/277V, 35KAIC - GE TYPE SPECTRA SERIES 069 X962821

3P200 A

3P200 A

3P250 A

MSB A

ROOM 118

3P30 A

3#1 +

1#6G

1 1/4"

C

B

4#3/0

+ 1#

6G2 1

/2"C

P/A

4#3/0

+ 1#

6G2 1

/2"C

P/M

4#10

+ 1

#10G

1/2"

C

NEUTRAL BUS

GROUND BUS

C 3P800 A

TO UTILITY XFMR TO FUSED DICONNECT SWITCHSERVING FIRE PUMP XFMR

TT-75

4#3/0

+ 1#

6G2 1

/2"C

4#25

0 KCM

IL + 1

#4G

3"C

P/H

3P125 A

3#1 +

1#6G

1 1/4"

C

A

TT-75

4#3/0

+ 1#

6G2 1

/2"C

3P125 A

400A3R

ECHILLER CH-1

3#4/0

+ 1#

4G2"

C3#

4/0 +

1#4G

2"C

SPD

EXISTING LOAD: 71.3 KVA (197.9A)REMOVED LOAD: 0.0 KVA (0.0A)ADDED LOAD: 7.2 KVA (19.9A)TOTAL LOAD: 78.5 KVA (217.9A)

EXISTING LOADS ARE BASED ON CONNECTEDLOAD FROM RECORD DRAWINGS AND ACTUALSITE CONDITIONS

3P150 A

1,600A, 3ø, 4W, 208Y/120V, 75KAIC - GE TYPE AV2 54962

3P150 A

3P225 A

3P100 A

SWITCHBOARD SWBD

ROOM 138

3P30 A

4#3/0

+ 1#

6G2 1

/2"C

LP14#

3/0 +

1#6G

2 1/2"

CLP2

4#30

0 KCM

IL + 1

#4G

3"C

LP3

4#10

+ 1

#10G

1/2"

C

NEUTRAL BUS

GROUND BUS

C 3P800 A

TO UTILITY XFMR TO FUSED DICONNECT SWITCHSERVING FIRE PUMP XFMR

3#2 +

1#8G

1 1/2"

C

3P225 A

3#30

0 KCM

IL + 1

#4G

2 1/2"

C

LP3A

4#1 +

1#6G

2"C

TT-30

ISO.XFMR

LP44#

1/0 +

1#6G

2"C

LP5

3P500 A

CHILLER

3P125 A

IRRIGATIONPUMP

3P30 A

PHWP1/PHWP2

3P30 A

BOILERPUMP #2

3P30 A

AHU-4

3P30 A

GROUNDSSHED

3P50 A

AHU-5

3P30 A

BOILERPUMP #1

3P30 A

AHU-3

3P100 A

AHU-1

3P30 A

SPARE

3P30 A

NORTHFOUNTAIN

3P40 A

SPARE

3P50 A

SPARE

3P30 A

CHILLEDWATER PUMP #1

SPD

EXISTING LOAD: 62.7 KVA (174.0A)REMOVED LOAD: 3.1 KVA (8.6A)ADDED LOAD: 2.2 KVA (0A)TOTAL LOAD: 61.8 KVA (165.4A)


EXISTING LOAD: 26.6 KVA (73.8A)REMOVED LOAD: 14.7 KVA (40.8A)ADDED LOAD: 5.2 KVA (0A)TOTAL LOAD: 17.1 KVA (33.0A)


No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

SHEET NOTES:

NOTES:

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:56

:3 6 P

M

EP601

SINGLE LINEDIAGRAMS

NGZ

SAE

SCALE: NOT TO SCALE

PARTIAL ONE LINE DIAGRAM - BLDG 2 - ACADEMSERVICES BUILDING1

SCALE: NOT TO SCALE

PARTIAL ONE LINE DIAGRAM - BLDG 1 - STUDENTSERVICES BUILDING2

NOTE:1. PANELBOARD "A" IS THE ONLY PANEL WHERE NEW LOADS ARE BEING ADDED TO THE ELECTRICAL SYSTEM.2. ALL EQUIPMENT SHOWN IS EXISTING TO REMAIN UNLESS NOTED OTHERWISE.

NOTE:1. NO NEW LOADS ARE BEING ADDED TO THE ELECTRICAL SYSTEM2. ALL EQUIPMENT SHOWN IS EXISTING TO REMAIN UNLESS NOTED OTHERWISE.

A. ALL ELECTRICAL EQUIPMENT INDICATED ON THIS SHEET ISEXISTING TO REMAIN. SHOWN FOR REFERENCE ONLY.


No 75040

STATE OF

EC

RREVEHNOMI

S

LICENSE

F LORIDA

Y

EF

S

RP

O

IS ENLGI

ONA

EENR

F

E

D

C

B

A

F

E

D

C

B

A

1 2 3 4 5 6 7 8

87654321

15008.02

sheet

job number

drawn by

date

seal/signature

checked by

revisions


of

drawing number

Telefax (407) 730-3603



EBAA

0000629C000564

Telephone

Interior Design



Orlando, Florida 32814(407) 730-8600



XXX

OCTOBER 23, 2015


consultant

ADDENDUM 1

NEW SMYRNA CAMPUS


10/23

/2015

12:56

:3 8 P

M

EP701

ELECTRICALPANELSCHEDULES

Checker

Author

1. CIRCUIT BREAKER SHALL BE UL LISTED FOR USE WITH EXISTING PANELBOARD.2. BID ALTERNATE

NOTES:TOTAL AMPS C-N: 220 TOTAL DEMAND: 61.19 170TOTAL AMPS B-N: 199 TOTAL CONNECTED: 78.79 219TOTAL AMPS A-N: 244 28902 23838 26053 KVA AMPS

83 8481 8279 8077 7875 REC RM 109B (NOTE 1) 20 1 720 540 1 20 REC RM 101 (NOTE 1) 7673 -- -- -- 2808 0 1 20 SURGE PROTECTOR 7471 CU-1 EXTERIOR (NOTES 1, 2) 30 2 2808 1200 1 20 RM 105 WIG DRYER 7269 -- -- -- 125 1200 1 20 RM 105 WIG DRYER 7067 RM 104 - FCU-1, FCU-2, FCU-3, FCU-4 (NOTES 1, 2) 20 2 125 2392 -- -- -- 6865 RM 105 BARBERSHOP REC 20 1 900 2392 2 30 WASHER/DRYER COMBO 6663 RM 105 BARBERSHOP REC 20 1 900 900 1 20 RM 105 BARBERSHOP REC 6461 RM 105 BARBERSHOP REC 20 1 900 900 1 20 RM 105 BARBERSHOP REC 6259 RM 105 BARBERSHOP REC 20 1 900 900 1 20 RM 105 BARBERSHOP REC 6057 RM 105 BARBERSHOP REC 20 1 900 900 1 20 RM 105 BARBERSHOP REC 5855 RM 105 BARBERSHOP REC 20 1 900 900 1 20 RM 105 REC 5653 RM 105 BARBERSHOP REC 20 1 900 900 1 20 RM 105 REC 5451 RM 105 BARBERSHOP REC 20 1 900 900 1 20 RM 105 REC 5249 RM 105 BARBERSHOP REC 20 1 900 900 1 20 RM 105 REC 5047 COKE MACHINE HALL 20 1 500 900 1 20 RM 105 REC 4845 LTG CONTROLS 20 1 500 900 1 20 RM 105 REC 4643 BARBER SHOP REC 20 1 1200 1080 1 20 RM 106 REC 4441 RM 105 MOTORIZED BED 20 1 800 720 1 20 RM 106 REC 4239 RM 105 MOTORIZED BED 20 1 800 720 1 20 RM 106 REC 4037 RM 105 MOTORIZED BED 20 1 800 720 1 20 RM 106 REC 3835 RM 105 MOTORIZED BED 20 1 800 720 1 20 REC RM 109B 3633 RM 105 MOTORIZED BED 20 1 800 420 1 20 RM 106 REC 3431 RM 105 MOTORIZED BED 20 1 800 420 1 20 RM 106 REC 3229 RM 124 REC 20 1 540 720 1 20 RM 107, 130 REC 3027 RM 105, 106, 107 PROJ. SCREEN 20 1 540 540 1 20 RM 107 INCUBATOR 2825 -- -- -- 3133 540 1 20 RM 107 REC 2623 -- -- -- 3133 720 1 20 RM 126, 127 2421 RM 107 STERILIZER 40 3 3133 720 1 20 RM 128, 129 2219 RM 107 STILL 20 1 1200 720 1 20 RM 107 REC 2017 RM 107 STILL 20 1 1200 720 1 20 RM 107 REC 1815 RM 107 FUME HOOD 20 1 1200 900 1 20 RM 131, 132 REC 1613 EF-1 20 1 864 1080 1 20 RM 108 REC 1411 UNKOWN 20 1 1920 900 1 20 RM 108 REC 129 -- -- -- 3000 720 1 20 RM 108 REC 107 UNKNOWN 20 2 3000 360 1 20 RM 108 REC 85 RM 117, HWRP 20 1 500 360 1 20 RM 108 63 RM 132 REC, EF-4 20 1 600 360 1 20 RM 108 REC 41 TRACK LTS 20 1 1900 360 1 20 180 REC 2

CKT CIRCUIT DESCRIPTIONTRIP

(AMPS) POLESPHASE A

(VA)PHASE B

(VA)PHASE C

(VA) POLESTRIP

(AMPS) CIRCUIT DESCRIPTION CKT

NOTES:ENCLOSURE: NEMA 1 MCB RATING: 200A

MOUNTING: SURFACE WIRE: 4 BUS RATING: 225 AFED FROM: TA PHASES: 3 MAINS TYPE: MCBLOCATION: ELECTRICAL 118 VOLTS: 208Y/120V A.I.C. RATING: 10,000A

PANEL: A

1. RE-USE EXISTING CIRCUIT BREAKER.NOTES:

TOTAL AMPS C-N: 17 TOTAL DEMAND: 10.52 29TOTAL AMPS B-N: 40 TOTAL CONNECTED: 11.04 31TOTAL AMPS A-N: 41 4560 4440 2040 KVA AMPS

23 SPACE ONLY -- -- 0 0 -- -- SPACE ONLY 2421 SPACE ONLY -- -- 0 0 -- -- SPACE ONLY 2219 SPACE ONLY -- -- 0 0 -- -- SPACE ONLY 2017 SPARE 0 1 0 0 1 0 SPARE 1815 REC RM 1046 - 1049 20 1 1500 0 1 0 SPARE (NOTE 1) 1613 REC RM 1053 20 1 1500 720 1 20 REC RM 139A (NOTE 1) 1411 SPARE 0 1 0 1500 1 20 REC RM 1046 129 REC RM 139A (NOTE 1) 20 1 180 1500 1 20 COVERED MALL 107 REC RM 139B (NOTE 1) 20 1 900 0 1 0 SPARE (NOTE 1) 85 REC RM 139A (NOTE 1) 20 1 180 360 1 20 REC RM 139A (NOTE 1) 63 REC RM 150 (NOTE 1) 20 1 720 540 1 20 REC RM 139A (NOTE 1) 41 REC RM 150 (NOTE 1) 20 1 720 720 1 20 REC RM 149 (NOTE 1) 2


(AMPS) POLESPHASE A

(VA)PHASE B

(VA)PHASE C

(VA) POLESTRIP


NOTES:ENCLOSURE: NEMA 1 MCB RATING: 100A

MOUNTING: WALL WIRE: 4 BUS RATING: 125 AFED FROM: T30 - ISO PHASES: 3 MAINS TYPE: MCBLOCATION: ELECTRICAL 137 VOLTS: 208Y/120V A.I.C. RATING: 10,000A

PANEL: LP4

BUIDLING 1 PANELS

BUIDLING 2 PANEL

1. RE-USE EXISTING CIRCUIT BREAKER.NOTES:

TOTAL AMPS C-N: 174 TOTAL DEMAND: 35.98 100TOTAL AMPS B-N: 176 TOTAL CONNECTED: 60.10 167TOTAL AMPS A-N: 156 18720 20840 20540 KVA AMPS

41 REC FLOOR BOX COVER MALL 20 1 1500 540 1 20 REC RM 135 (NOTE 1) 4239 VENDING MACHINES 20 1 1500 540 1 20 REC RM 139B (NOTE 1) 4037 VENDING MACHINES 20 1 1500 540 1 20 REC RM 150 3835 REC RM 117, 119, 126, 138, 141 20 1 1400 900 1 20 REC CLASSROOM 149 3633 COPIER RM 130 20 1 800 1500 1 20 TELEPHONE BACBKBOARD TTB-1 3431 REC RM 130 20 1 800 1400 1 20 REC RM 122 3229 REC RM 134, 131 20 1 1600 1000 1 20 REC RM 116 3027 REC RM 132, 133 20 1 1600 1000 1 20 REC RM 114 2825 REC ROOM 139A, 136 (NOTE 1) 20 1 360 900 1 20 REC RM 111 (NOTE 1) 2623 REC ROOM 139A, 139B (NOTE 1) 20 1 900 1200 1 20 REC RM 116 2421 REC RM 144 20 1 1200 1200 1 20 REC RM 114 2219 REC RM 144 20 1 1200 720 1 20 REC RM 111 2017 REC RM 146 20 1 1200 1200 1 20 REC RM 110, 110A 1815 REC RM 146 20 1 1200 1400 1 20 REC RM 109, 109B 1613 CHEM BIO LAB FUME HOOD 20 1 500 1000 1 20 REC RM 109 1411 CEILING MOUNTED PROJECTOR 139B 20 1 500 1000 1 20 REC RM 108 129 SHUNT TRIP BREAKER 20 1 500 1200 1 20 REC RM 105 107 CHEM BIO LAB VENT 20 1 1200 1200 1 20 REC RM 106, 105, 108 85 -- -- -- 6200 1400 1 20 REC 103, 104, 151F, COVERED MALL 63 -- -- -- 6200 1000 1 20 REC RM 102 41 PANEL LP3A 100 3 6200 1200 1 20 REC RM 101, 101A 2


(AMPS) POLESPHASE A

(VA)PHASE B

(VA)PHASE C

(VA) POLESTRIP


NOTES:ENCLOSURE: NEMA 1 MCB RATING: N/A

MOUNTING: WALL WIRE: 4 BUS RATING: 225 AFED FROM: SWBD PHASES: 3 MAINS TYPE: MLOLOCATION: ELECTRICAL 138 VOLTS: 208Y/120V A.I.C. RATING: 10,000

PANEL: LP3


Documents

NEW SMYRNA CAMPUS BUILDING 1 AND BUILDING … 16-008 Addendum.pdfaddendum 1 october 23, 2015 new smyrna campus building 1 and building 2 remodel efis # 2639-1 project number: 15008.02