1

Audio System Handbook

Blaupunkt 520

2

3

:

; < ?= >

987654321

4

@

A

B

C

D

E

LHS Steering Remote Control RHS Steering Remote Control

1

Security CodeYour radio includes an electronically codedsecurity system. This security system relieson an unique PIN code to enable operationof your radio. The number only needs to beentered if the car's battery has beendisconnected or if the radio has beenremoved from the car. Please refer to thesecurity release procedure.

If an incorrect PIN code is entered, the radiowill not operate, and there will be a timedelay before the PIN code can be re-entered.

DO NOT SWITCH OFF THE RADIODURING THE WAITING TIME.

The waiting time is approximately 10seconds for the first 2 attempts, then 10minutes, and up to 11 hours by the tenthattempt. The number of attempts remainingis shown in the display.

After the tenth attempt 'DEALER' appears inthe display and the set is blocked. Contactyour Holden Retailer to put the set back intooperation.Because the PIN code is the only means ofenabling operation of the radio, werecommend that the Security Card is kept ina safe location.

DO NOT LEAVE IT IN THE GLOVEBOXOF YOUR CAR.

The PIN code should also be written downand kept with other important documents.

If your card is lost, and the PIN code is notrecorded elsewhere, the PIN can berequested from your Holden Retailer, aftersupplying the requested ownershipinformation. There may be a charge for thisservice.

Please note:For added security a small red light on theradio blinks while the ignition is off.

Security Release ProcedureRadio PIN Code:

1. Switch on ignition.

2. Switch on the radio, if turned off.

3. The display shows 'CODE'.

4. Press and hold AS button 8, until abeep is heard and release the AS-button.

The display shows '10 _ _ _ _', whichindicates that you have ten attempts leftat entering the correct PIN code.

5. Enter the PIN code (see Security Card)with preset buttons 1, 2, 3 and 4.

Example:

If the PIN code belonging to the radio is3650.

Display:

Press preset button 1 4 times 10 3 _ _ _

Press preset button 2 7 times 10 3 6 _ _

Press preset button 3 6 times 10 3 6 5 _

Press preset button 4 1 time 10 3 6 5 0

6. Press AS button 8 until a beep is heardand the radio starts operating.If a wrong PIN code has been enteredthe display will show '9 SAFE'. After thewaiting time '9 _ _ _ _' will be shown onthe display indicating that there are nineattempts left. The correct code shouldnow be entered.

2

In CarEntertainmentThis handbook contains all the informationyou will need to operate the in-carentertainment equipment fitted in yourHolden car. It is recommended that you readthis handbook as this will greatly assist inobtaining the best performance from yoursystem.

There are also sections on radio receptionand care and maintenance of your CD's. Wewish you many hours of pleasurablelistening.

ContentsSecurity Code ............................................ 1

In CarEntertainment ............................................ 2

Contents .................................................... 2

Overview .................................................... 3

Switching on/off ......................................... 4

Volume Control .......................................... 4

Tone Control .............................................. 4

Radio ......................................................... 5

Storing Stations ......................................... 6

Radio Reception ........................................ 7

CD Operation ............................................ 8

Steering WheelMounted Remote Controls ...................... 11

Additional Features .................................. 12

Car Telephone ......................................... 13

Master Reset ........................................... 14

3

= [1] - [6] Memory Preset stations1 to 6

> - Volume control: TurnAudio menu: Push (Bass /Treble / Fader / Balanceselector)

? - Security indicator light

OverviewControlsNo. Symbol Function

1 CD eject

2 CD CD on / Pause selector

3 TR SCN CD mode: Track scan

4 TR RPT CD mode: Track repeat

5 TR RDM CD mode: Random track play

6 - CD loading slot

7 LOC Radio mode:Local/Distance selector

8 AS Radio mode:Automatic storing of radiostations

9 AM AM /FM Band selectionFM

: ON Press to switch radio on/off

; <TUNE/ Radio mode: Manual tuningTRACK> CD mode: Track selection

< <<SEEK>> Radio mode: Seek tuning

Steering Wheel MountedRemote Controls (if fitted)No. Symbol Function

@ Radio mode:Seek tuning upwardsCD mode:Select next track / cue

A Radio mode:Seek tuning downwardsCD mode:Select previous track / review

B ↑ Radio mode:Station preset selectionCD mode:Restart CD at beginning

C + Increase volume,Audio menu: Increase setting

D - Decrease volume,Audio menu: Decrease setting

E O Source select:FM1 - FM2 - AM - CD - FM1etc. (or FM AS - AM AS - CD -FM AS etc. respectively)Audio menu:Bass - Treble - Fader - Balance

4

Switching on/offOn/Off (using ignition key)

When the car's ignition is switched off andthe key removed, the radio (if operating) willbe switched off. When the ignition isswitched on again the radio will also beswitched on.

On/Off (without ignition key)

The radio can also be switched on and offwithout using the car's ignition key bypressing the on/off button :. The radio willoperate for approximately 1 hour. Once thisperiod has elapsed the radio automaticallyswitches off and will not operate until theon/off button : is pressed again.

The radio can be turned on (if off) with thefollowing buttons/operation:

• ON button :

• AM FM button 9

• CD button 2

• CD insertion

Volume ControlVolume

Turning the knob > clockwise will increasethe level, turning it anticlockwise willdecrease the level.

Press knob > to activate and changeAudio mode (Bass - Treble - Fader -Balance). The active mode will be shown onthe display. After 2 seconds the display willreturn to former mode.

Please note:When the radio is turned on, it will return tothe volume level that was last used, unlessthis level exceeds a factory predeterminedlimit, in which case it will resume at this limit.

This predetermined limit can be changed byyour Holden retailer.

Fader ControlTo shift sound towards the rear or front,press the audio selector (Volume knob) threetimes, to select the Fader mode. This will beconfirmed on the display by 'FADER' withthe current setting. While in this mode, turnselector knob clockwise or anti-clockwise toshift the sound towards the front or rear.After 2 seconds the display will return to theformer mode.

If there are only front speakers fitted to thevehicle (check with your retailer) thenadjusting the fader function to the rear willnot produce any sound.

Balance

To shift the sound towards the right or theleft press the audio selector (Volume knob)four times, to select the Balance mode.

This will be confirmed on the display by'BALANCE' with the current setting. While inthis mode, turn selector knob clockwise oranti-clockwise to shift the sound towardsthe right or left. After 2 seconds the displaywill return to the former mode.

Tone ControlIndependent Tone Memories

This radio is equipped with IndependentTone Memories. Bass and Treble can beindependently set for each listening modesuch as AM, FM, CD and Telephone.

In addition, volume, fader and balance canbe adjusted in Telephone mode withoutaffecting these settings in Radio or CDmode.

Bass

Press the audio selector (Volume knob)once, to select the Bass mode. This will beconfirmed on the display by 'BASS' with thecurrent setting. While in this mode, turn theselector knob clockwise or anti-clockwise toadjust the bass to the desired level. After 2seconds the display will return to the formermode.

5

AM 1017

FM 105.9LOCAL ON

RadioSelecting WavebandAM Band:

Press AM/FM button 9 to select AM band.

FM Band:

Press AM/FM button 9 to select FM bandor to switch between FM1, FM2 and AM.

Station on AM Band

Station on FM Band

Stereo Broadcast:

When a stereo broadcast is received on FM,the stereo indicator ' ' appears in thedisplay. In case of poor field-strength theradio automatically switches to mono butthe ' ' indicator may still be shown on thedisplay.

Tuning-in a station

You can tune-in stations in different ways:

• Automatic seek

• Manual seek

• Auto-store (AS)

Automatic Seek Tuning

This function seeks radio stationsautomatically. Press button SEEK>> <to automatically select the next higherfrequency radio station. Press button<<SEEK < to automatically select the nextlower frequency radio station. During thisoperation, the radio is muted. As the radiocan seek weak and noisy distant radiostations, it is recommended to switch theradio to 'local' mode.

To do this, press LOC button 7. Thecurrent mode ('LOCAL ON' or 'LOCAL OFF')is displayed. Press the LOC button 7 againto switch between 'LOCAL ON' or'LOCAL OFF' mode.

• In LOCAL ON mode, the radio will firstsearch for strong stations. If no strongstation can be found it will search forany receivable station.

• In LOCAL OFF mode the radio willsearch for any receivable station (usefulin areas where there are no strongstations).

The LOCAL ON/OFF setting does not affectthe AS function (refer to section 'AutomaticStoring' elsewhere in this handbook).

Treble

Press the audio selector (Volume knob)twice, to select the Treble mode. This will beconfirmed on the display by 'TREBLE' withthe current setting. While in this mode, turnthe selector knob clockwise or anti-clockwise to adjust the treble to the desiredlevel. After 2 seconds the display will returnto the former mode.

6

Programming by Automatic Storing

Select the desired waveband with the AM/FM button 9.

Press AS button 8 for at least 2 secondsuntil the audio is briefly muted or beep isheard (if beeps are turned on). Search tuningstarts. 'AS' appears in the display.

Search tuning during Auto-Store

After the Auto-Store process has finished,the six strongest stations in this receptionarea are stored. The radio will play thestation stored on preset 1.

If you have travelled beyond the range of thestored stations, you may wish to repeat theprocess again to store new strong stations.

To alternate between the AS radio stationsand your normally stored radio stations (onFM1, FM2 or AM), briefly press the buttonAS 8.

Whenever you are using the AM AS or theFM AS bands, 'AS' will also be shown in thedisplay.

Station on FM AS Stored on Preset 4

Manual tuning

To tune-in stations of which the frequency isknown, press and hold one of the tuningbuttons TUNE> ; or <TUNE ;.

Fast tuning starts and will continue until yourelease the button. During this operation theradio is muted.

Briefly tap tuning button TUNE> ; or<TUNE ; to move in steps of 9 kHz for AMor 0.1 MHz for FM until the right frequency isdisplayed.

Storing StationsStorage locations for 30 stations areavailable.

• 6 x FM1

• 6 x FM2

• 6 x AM

• 6 x FM AS(Automatically-Stored FM stations)

• 6 x AM AS(Automatically-Stored AM stations)

Storing a Radio Station into aPreset1. Select the required waveband, AM, FM1

or FM2 by button AM/FM 9.2. Tune to the desired station by means of:

• Automatic seek tuning or• Manual tuning

3. Press and hold the desired presetbuttons 1 to 6 (=) until the radio isbriefly muted or beep is heard (if beepsare turned on), indicating that the chosenradio station is stored into the preset.

During the storing process the currentlystored station is shown.

FM Station stored on Preset 1

The previously stored station is thenreplaced and the selected preset number'1 to 6' appears in the display.

4. Program the other preset buttons in thesame way.

5. Repeat the above mentioned operationfor the other wavebands AM, FM1 andFM2.

Automatic Storing (AS)This feature allows the storage of an extra 6AM and 6 FM radio stations. It is of greatbenefit when away from the home location,as the strongest radio stations can bestored without knowing their frequency, anddoes not delete the stations already storedon FM1, FM2 or AM bands.

P1 101.4 AS 103.7AS

P4 103.7AS

7

You can also store stations manually on theAS storage locations (see 'Storing a RadioStation into a Preset' elsewhere in thishandbook).

Recalling Stored StationsSelect waveband AM or FM with the buttonAM/FM 9.Press the desired preset button.To select one of the stations stored withAuto-Store, select waveband AM or FM,then briefly press AS button 8 and pressthe desired preset button.

Radio ReceptionDue to varying reception locations, carradios have performance limitations thatmay on occasions create the impressionthat your radio is malfunctioning. To assistyou in understanding what can be expectedfrom your radio, we have set out below howreception may vary from time to time andunder certain conditions.

AM and FM:There are two types of radio broadcasts inAustralia. AM or Amplitude Modulation inwhich the amplitude of the signal is varied toproduce the sound and FM or FrequencyModulation in which the frequency is variedto produce the sound.

Range:AM broadcasts tend to follow the earth'scurvature and also reflect from the upperatmosphere, in which enables long rangereception, especially after sunset.

FM transmissions are basically line-of-sight(similar to TV signals) and are reflected bybuildings, mountains etc., but not by theupper atmosphere.

Interference:Interference is caused by either natural orman made electrical disturbances. This canaffect the amplitude of the signal beingreceived. AM signals are more prone to thistype of interference than FM signals. Thistype of interference has little or no effect onthe frequency of the received signal, thusAM is susceptible to interference from powerlines, fluorescent lighting, neon signs, trafficlight control circuits, overhead tram wiresand electrical storms. With FM reception,these amplitude variations are filtered out,leaving a relatively clear signal (refer to'Peculiarities of FM Mobile Reception),making this one of the major advantages ofFM broadcasts.

Peculiarities of FM MobileReception:A mobile FM radio cannot be expected tocontinously provide the quality of FMreception you may have experienced onyour home radio. Contrary to popularopinion, FM broadcasts are not static free,and although your new radio has a built-inelectronic interference absorption circuit,some static will be evident from time to time,

especially in areas without a direct line ofsight to the transmitter.

Your radio is also equipped with a soft mutefunction. The purpose of this is to attenuatethe treble and audio level in weak signalareas to reduce the very annoyingbackground hiss, which is customary toweaker FM reception. There are two pheno-mena peculiar to FM reception.

• Flutter - As FM signals reflect off solidobjects, it is possible to pass throughareas of 'SHADOW' caused by tallbuildings and/or hilly terrain, whicheffectively blocks out the signal. As thecar passes in and out of shadow areas,the level of signal will vary at a rapid rate,creating a flutter type of interference tothe signal.

• Distortion (Multipath) - Distortionmay occur when the direct signal from thetransmitter and a reflected signal reachthe antenna at the same time and eithercancel or aid each other, like ghosting ona TV. This results in intermittent distortionof the signal whilst moving or constantdistortion when stationary, such as at atraffic light or when parked. Should thisdistortion occur while stationary, movingthe car approximately 1 or 2 metreswould on most occasions correct theproblem. Circuitry has also been includedin this radio to reduce this type ofdistortion.

8

CD OperationCD LoadingEnsure that the CD entry slot 6 is clear.Insert the CD (lettered side up) into the slotuntil the CD is automatically received andtaken.

The CD operation will automatically overridethe radio. The display shows 'CD'.

After the CD has been accepted, the playerbegins with the first track on the CD. Initiallythe total number of tracks on the CD isshown as 'TxxCD' followed by:

After the last track has been played,playback of the CD begins again, startingwith the first track.

If the CD has been inserted incorrectly, thedisplay will show 'CD ERROR'.

Please note:It is possible to insert and load a CD whilethe car's ignition is turned off. Playback willcommence immediately after the CD isloaded.

CD SelectionPress CD button 2 to activate the CDmode.

If you select the CD mode and there is noCD in the radio the display shows 'NODISC' for 2 seconds. The radio will continueplaying.

CD PausingPressing the CD button 2 while playing adisc will pause the CD.

The display will show:

To resume the playing of the CD pressbutton 2 again.

Track SelectionYou can select a desired track on a CD bybriefly pressing button ; <TUNE/TRACK>

Press button TRACK> ; to go on the nexttrack or press repeatedly until desired trackappears in the display.Press button <TRACK ; to go back to thestart of the current track or press repeatedlyuntil desired track appears in the display. Ifthe track has been playing for less than 3seconds and button <TRACK ; is pressed,the previous track will be played. If youpress button <TRACK ; after the first 3seconds, the current track is restarted.

Fast Forward / Fast Back (TrackCue/Review)Press button ; <TUNE/TRACK> for morethan 2 seconds to rapidly move forward orbackwards within the current track. The CDis played at a faster speed and at a lowervolume. The display shows the number ofthe track and the elapsed time of the trackin minutes and seconds.

01 CD TRACK DISC IN

PAUSE

To reduce the effects of interference and/orpoor signal strength, several features havebeen included within the radio which workautomatically when needed:

• Noise Blanking Circuit(FM interference suppression) - To reducepulse interference, a Noise BlankingCircuit is included.

• Soft Muting Circuit - The built-in SoftMuting Circuit will reduce the FM stereoseparation and treble response if thesignal from the radio station diminishes.This effectively lessens the amount of hissand background noise that is usuallyheard with weaker FM signals.

• Multipath Detection Circuit - Ifrepeated multipath signals are received,the circuitry will switch the radio intoMONO mode and slightly reduce thetreble response. It will gradually return toSTEREO with full treble response whenmultipath conditions are no longer beingexperienced.

9

Track ScanPress the TR SCN button 3 to sequentiallysample the first 10 seconds of all tracks onthe CD. During the track scan the displayshows:

The track number is flashing.

Press the TR SCN button 3 again to stopscanning and listen to the current track.

Track RepeatPress the TR RPT button 4 to replay thecurrent track. The track repeat will beconfirmed by the following display:

Press the button TR RPT 4 again to stopthe repeating or press button ; <TUNE/TRACK> to go to the next or previous (referto section headed 'Track Selection'elsewhere in this handbook).

TRACK DISC IN

05 RPT

TRACK DISC IN

10 SCAN

Random PlayWhen this feature is selected, all tracks onthe CD will be played randomly.

To switch on the random play, pressTR RDM button 5 during CD playback.Random play will be confirmed by thefollowing display:

To switch off the random play press theTR RDM button 5 again during CDplayback.

If button ; <TUNE/TRACK> is pressedwhilst in random play mode, the nextrandom selection will play.

Once all tracks on the CD have beenrandomly played, the display will show'RANDOM RPT' and the CD will berandomly played again.

CD Eject

Press the button 1 to eject the CD.The radio will display 'EJECT CD' then revertto radio mode.

If the CD is not removed within 10 secondsof being ejected, it is automatically reloadedinto CD player again (to protect the CD fromaccidental damage). In this case, the radiowill remain in radio mode.

The display shows the symbol 'DISC IN'.

Please note:It is possible to eject the CD when the car'signition is turned off.

Stopping CD playbackPress the the button AM/FM 9 briefly tostop CD playback and resume in radiomode or press the button ON : to switchthe radio off.

Error Messages from the CDDeckIn some cases it may happen that the deckis not able to play or load a specific CD.Then the following error messages areshown in the display:

1. 'CD ERROR' (after CD loading): A CD iscaught in the deck mechanism.

2. 'CD ERROR' (during CD playback): Thedeck mechanism is too hot. Allow the CDdeck to cool down before resumingoperation.

3. 'CD ERROR' (constantly after selectingCD mode): Internal control error.

TRACK RDM DISC IN

12 CD

CD ERROR

10

• Before inserting into the radio, clean theCD with a cleaning cloth. Wipe the CDfrom the centre outwards, rather than ina circular motion. See diagram

• Do not use solvents such as petrol,thinners etc. Use commercially availableCD cleaners.

Notes on Compact Discs• Handle the CD by its edge and avoid

touching the playing surface.

• Do not stick paper or tape or write oneither surface.

• Do not expose the CD to direct sunlightor a heat source such as a hot air duct.

4. 'CD ERROR' (after CD loading): CDcannot be read anymore; after displaying'CD ERROR' the radio ejects the CD.Check if CD was loaded upside down(the label surface should be facingupwards). This message may also bedisplayed if a CD is dirty or scratched.Inspect the CD surface for problems andclean if necessary. "CD ERROR" will alsobe seen when try to play e.g. MP3 CD,Video CD, DVD or CD-ROM.

The radio switches back to radio mode.

Consult your Holden Retailer, if you read anyof the error messages.

Please note:• For trouble free CD operation, ensure that

no foreign objects are inserted throughthe CD opening.

• Do not insert and force two CD's into theopening at the same time, they will jamand not play.

• If a CD is already in the mechanism, asecond CD cannot be inserted.

• Also refer to the section headed 'Noteson Compact Discs' elsewhere in thishandbook.

11

E O Source select:FM1 - FM2 - AM - CD - FM1etc. (or FM AS - AM AS - CD -FM AS etc. respectively)Audio menu:Bass - Treble - Fader - Balance

Preset Station and CD selectBriefly pressing the button ↑ B on thesteering wheel remote will perform thefollowing functions:

Radio – Advances to the next stored radiostations on the current AM or FM band inincreasing preset number.

CD – Restarts playing at the beginning ofthe CD.

Search Radio Station or TrackSelectBriefly pressing the button @ on thesteering wheel remote will perform thefollowing functions:

• Radio – Searches for the next receivableradio station on the current AM or FMband in increasing frequency.

• CD – Advances to the next track on theCD.

Pushing and holding this button for2 seconds or more:

• CD – Rapidly moves forward within thetrack (cue).

Steering WheelMounted RemoteControls (if fitted)To increase driving safety and to improveease of operation, some of the radiofunctions can be controlled by the remotecontrols on the steering wheel.

The following functions are available (forillustration see fold-out page):

OverviewNo. Symbol Function

@ Radio mode:Seek tuning upwardsCD mode:Select next track / cue

A Radio mode:Seek tuning downwardsCD mode:Select previous track / review

B ↑ Radio mode:Station preset selectionCD mode:Restart CD at beginning

C + Increase volume,Audio menu: Increase setting

D – Decrease volume,Audio menu: Decrease setting

Briefly pressing the button A on thesteering wheel remote will perform thefollowing functions:

• Radio – Searches for the next receivableradio station on the current AM or FMband in decreasing frequency.

• CD – Returns to the start of the currenttrack, or previous track.

Pushing and holding this button for2 seconds:

• CD – Rapidly moves backward within thetrack (review).

Volume AdjustmentThe button + C or button – D adjusts thevolume up or down respectively. Thebuttons can either be pressed and held untilthe desired volume is reached, or brieflypressed several times to raise or lower thevolume gradually.

Source SelectionPress the button O E to scroll through all ofthe sources in the following order:

FM1 - FM2 - AM - CD - FM1etc.

Or, if the AS indicator is shown on thedisplay:

FM AS - AM AS - CD - FM AS etc.

12

1. Press button LOC 7 for at least 3seconds until you hear a confirmationbeep (no beep if 'BEEP OFF' previouslyset). The display shows the currentsetting, for eg. 'SD-VOL 2'.

2. Press tuning buttons (;) within8 seconds to select the desired settingbetween 'SD-VOL 0' and 'SD-VOL 5'.

3. To store the selected setting, pressbutton LOC 7 again for at least 3seconds until you hear a confirmationbeep (no beep if 'BEEP OFF' previouslyset).

Display during setting for speed dependentvolume control.

If you don't store the new setting within8 seconds after the last press of a button, itwill not be stored. To turn this feature off,select and save 'SD-VOL 0'.

Additional FeaturesSpeed dependent volume controlThe speed dependent volume controladjusts the volume depending on the vehiclespeed. As the vehicle increases in speed,the volume of the radio also increases tocompensate for the associated speednoises.

Please note:This feature will not always compensate forthe driving noise. There are other variablefactors such as road surface, wind noise,windows open, engine speed etc. that mayalter the interior noise for any given roadspeed.

For this reason there are five different levelsof compensation available to allow you tofind the level of compensation that best suitsyour average driving conditions.

You can select the compensation curvesbetween 0 (off) and 5 (maximum compensa-tion) as follows:

Audio Menu AdjustmentPress the volume control > to activate andselect audio menu.

When any of the audio menu (Bass/Treble/Fader/Balance) is on the display, you canselect the next menu by pressing the buttonO E once or as many times as required.

Increase or decrease the setting by pressingthe button + C or - D.

SD-VOL 2

13

Confirmation BeepsAudible beeps are used to confirm variousactions of the radio such as storing a radiostation or an automatic store is started. Thebeeps can be turned on or off as follows.

1. Switch off the radio by pressing buttonON :.

2. Press preset buttons 3 and 5 (=)together and keep pressed.

3. Switch on the radio and keep preset but-tons 3 and 5 (=) pressed until thedisplay shows 'BEEP OFF' or'BEEP ON'.

4. Select 'BEEP ON' or 'BEEP OFF' withthe tuning buttons (;).

5. To store the new setting press presetbuttons 3 and 5 (=) again for at least 3seconds until you hear a confirmationbeep.

Display during adjustment of confirmationbeep.

If you don't store the setting within 8seconds after the last press of a key, thenew setting will not be stored.

Car TelephoneThis radio includes a telephone input facility.If a mobile phone hands-free kit with suitablefeatures (such as a mute line and wiring forseparate speaker) has been connected to it,the radio will be muted when the phonerings and the voice of the caller will be heardthrough the car’s speakers. When the callends the radio will return to the previousmode.

During a call 'PHONE' will be shown on thedisplay.

If the radio system is off, it will turn on forthe telephone call if the car’s accessories orignition is already switched on.

If a call is in progress when the accessoriesare turned off and keys are removed fromignition, the radio will remain turned on inTelephone mode until the phone call iscompleted, i.e. does not interrupt yourphone conversation.

Volume, Bass, Treble, Fader and Balancecan all be adjusted in the Telephone modewithout affecting these settings in radio orCD mode.

Important

When this feature is used for the first time,the volume may need to be adjusted on thephone as well as the radio. This should bedone while a call is being made. Firstly,adjust the phone’s volume to a medium levelusing the volume control on the phone itself.The radio’s volume may now be adjusted asrequired to compensate for variations in themobile phone signal quality or changes inthe background noise within the car e.g. ifthe window is wound down.

Please Note:

If the call sounds unusually distorted, thevolume setting on the phone itself may needto be adjusted until the sound quality isimproved.

Please contact your Holden Retailer orBlaupunkt for further information.

BEEP ON

14

Master ResetThe radio has a reset function built in toenable you to instantly reset all adjustmentto the factory standard. This feature is mostuseful when adjustments have been madethat affect the sound quality or operation ofthe radio and you are unsure of how toreturn the original neutral settings. MasterReset will reset the followings:

• Bass, Treble, Fader, Balance to standard

• Volume

• Confirmation Beeps

• Phone volume

Performing the Master Reset1. Turn off the radio.

2. Simultaneously press and hold thepreset button 4 = and the button ON: for 3 seconds.

After the reset this radio will turn on with thestandard settings, no message will bedisplayed.

15

NOTES:

16

NOTES:

5

Please note, that all information, illustrations and specifications in this Handbook are basedon the latest production information available at the time of printing.

Holden reserves the right to make changes at any time without notice and without incurring any obligation.

© 2002 Holden Ltd.

Reproduction in whole or in part is prohibited without written approval fromHolden Ltd., ABN 84 006 893 232.

6

U1E

Holden Part No: 92057925

Bosch Part No: 8 622 403 494