Upload
doannga
View
213
Download
0
Embed Size (px)
Citation preview
TECHNICAL DATA
Nemo2 20_XS 23_S 25_M 28_L 31_XL
Certification EN A EN A EN A EN A EN A
LTF A LTF A LTF A LTF A LTF A
Number of cells 38 38 38 38 38
Surface area (flat) [m 2] 20,00 23,40 25,50 28,00 31,00
Surface area (projected) [m 2] 17,55 20,53 22,38 24,57 27,20
Span (flat) [m] 9,69 10,49 10,95 11,47 12,07
Span (projected) [m] 7,92 8,57 8,94 9,37 9,86
Aspect Ratio (flat) 4,70
Aspect Ratio (projected) 3,57
Sink rate [m/s] min = 1,1; trim = 1,2; max = 2,0
Speed [km/h] min = 22; trim = 37; max = 46
Max. cord [cm] 255,62 276,49 288,62 302,44 318,23
Min. cord [cm] 63,91 69,12 72,15 75,61 79,56
Distance pilot to w ing [cm] 620,55 671,21 700,65 734,20 772,53
Total line lenght [m] 303,50 328,28 342,68 359,09 377,83
Weight range [kg] 40-65 59-80 65-95 80-115 100-140
Weight [kg] 5,3 5,7 6,1 6,5 6,9
Lines Technora: 1,2 & 1,3 & 1,5 & 1,8 & 2,3
Fabric Dominico tex 45 g/m2
Dominico tex 40 g/m2
Dominico tex Hard 40 g/m2
SR Scrim, SR Laminate 180 g/m2
Risers PASAMON - Bydgoszcz, Polska
The latest version of service manual is available at: www.dudek.eu/en/service-and-inspections/
SERVICE MANUAL
TECHNICAL INSPECTIONS
Full inspection is recommended every 24 months, if not advised otherwise by the inspecting person due to current paraglider condition.
Paragliders in commercial use (training and tandem flights) should be undergoing Full Inspection every 12 months (excluding first 24-month period after purchase).
Technical inspection is carried out by the manufacturer or authorised person.
Length of the lines
Total suspension lines length, measured from the lower surface of the canopy to the inside edge of the maillon (tolerancy +/- 10 mm)
Nemo2 - 20_XS
The tables / Tables / Tabele:
The individual lenghts and type of line The total lenghts
La longueur et le type de chaque ligne Longueur des suspentes
D³ogoœci i rodzaj poszczególnych linek Sumaryczna d³ugoœæ linek
a b c d br a b c d br
1 2275 2260 2275 2295 1000 1 5645 5585 5680 5830 6490
2 2210 2200 2210 2230 860 2 5585 5520 5615 5760 6350
3 2250 2240 2245 2265 785 3 5620 5560 5650 5795 6280
4 2150 2120 2140 2185 945 4 5620 5555 5640 5780 6205
5 2120 2090 2105 2140 890 5 5590 5530 5610 5735 6145
6 2155 2135 2145 2170 910 6 5630 5575 5645 5765 6170
7 1790 1690 1650 1735 925 7 5565 5535 5590 5675 6100
8 1700 1610 1555 1615 840 8 5470 5450 5495 5560 6020
9 1615 1540 1475 1515 830 9 5385 5380 5415 5455 6005
10 815 10 5215 5185 5190 5230 5995
11 805 11 5990
12 855 12 6040
13 800 13 5985
14 735 14 5915
15 715 15 5900
16 710 16 5865
17 680 17 5835
18 685 18 5840
A B C D BR
1 3370 3325 3405 3525 1150
2 3470 3440 3500 3590 915
3 3770 3840 3940 965
4 970
5 780
6 750 Technora 7343-090-005:
A B C D BR Technora 7343-140-006:
I 2115
II 1980 Technora 7343-190-024:
III 2175
Technora 7343-280-011:
st1 1125 ST1 4085
st2 1095 Technora 7343-280-018:
st3 1100
st4 1135 brmain 2250 Technora 7343-420-041:
Total suspension lines length, measured from the lower surface of the canopy to the inside edge of the maillon (tolerancy +/- 10 mm)
Length of the lines
Nemo2 - 23_S
The tables / Tables / Tabele:
The individual lenghts and type of line The total lenghts
La longueur et le type de chaque ligne Longueur des suspentes
D³ogoœci i rodzaj poszczególnych linek Sumaryczna d³ugoœæ linek
a b c d br a b c d br
1 2455 2445 2460 2485 1080 1 6150 6080 6180 6340 7035
2 2395 2380 2390 2415 930 2 6085 6015 6110 6270 6880
3 2435 2425 2435 2455 855 3 6130 6060 6155 6310 6805
4 2325 2290 2310 2360 1020 4 6130 6055 6145 6290 6725
5 2290 2260 2280 2315 960 5 6095 6030 6110 6245 6665
6 2335 2310 2320 2350 985 6 6140 6080 6150 6280 6685
7 1940 1830 1785 1875 1000 7 6065 6035 6095 6185 6615
8 1835 1740 1685 1750 910 8 5965 5945 5990 6060 6525
9 1745 1665 1595 1635 900 9 5870 5870 5905 5945 6515
10 880 10 5690 5655 5660 5700 6505
11 870 11 6500
12 930 12 6555
13 865 13 6495
14 795 14 6425
15 775 15 6405
16 770 16 6370
17 740 17 6340
18 740 18 6345
A B C D BR
1 3690 3635 3720 3850 1240
2 3805 3765 3835 3925 995
3 4125 4205 4310 1045
4 1050
5 840
6 815 Technora 7343-090-005:
A B C D BR Technora 7343-140-006:
I 2280
II 2145 Technora 7343-190-024:
III 2360
Technora 7343-280-011:
st1 1215 ST1 4465
st2 1185 Technora 7343-280-018:
st3 1190
st4 1230 brmain 2450 Technora 7343-420-041:
Total suspension lines length, measured from the lower surface of the canopy to the inside edge of the maillon (tolerancy +/- 10 mm)
Length of the lines
Nemo2 – 25_M
The tables / Tables / Tabele:
The individual lenghts and type of line The total lenghts
La longueur et le type de chaque ligne Longueur des suspentes
D³ogoœci i rodzaj poszczególnych linek Sumaryczna d³ugoœæ linek
a b c d br a b c d br
1 2565 2550 2565 2590 1130 1 6440 6370 6470 6635 7335
2 2500 2485 2495 2520 970 2 6375 6305 6405 6565 7170
3 2545 2530 2540 2560 890 3 6420 6350 6450 6610 7095
4 2425 2390 2410 2465 1065 4 6425 6350 6440 6590 7010
5 2395 2360 2380 2420 1005 5 6390 6320 6405 6545 6950
6 2435 2415 2420 2450 1030 6 6435 6370 6450 6580 6975
7 2025 1910 1865 1960 1040 7 6360 6325 6390 6485 6900
8 1920 1820 1755 1825 950 8 6250 6235 6285 6350 6805
9 1820 1740 1665 1710 940 9 6155 6150 6195 6235 6795
10 915 10 5965 5930 5935 5975 6785
11 910 11 6780
12 970 12 6835
13 905 13 6775
14 830 14 6700
15 810 15 6680
16 800 16 6645
17 770 17 6615
18 775 18 6620
A B C D BR
1 3875 3820 3905 4040 1295
2 4000 3960 4025 4125 1035
3 4335 4415 4525 1090
4 1100
5 880
6 850 Technora 7343-090-005:
A B C D BR Technora 7343-140-006:
I 2380
II 2240 Technora 7343-190-024:
III 2465
Technora 7343-280-011:
st1 1270 ST1 4690
st2 1235 Technora 7343-280-018:
st3 1245
st4 1280 brmain 2550 Technora 7343-420-041:
Total suspension lines length, measured from the lower surface of the canopy to the inside edge of the maillon (tolerancy +/- 10 mm)
Length of the lines
Nemo2 - 28_L
The tables / Tables / Tabele:
The individual lenghts and type of line The total lenghts
La longueur et le type de chaque ligne Longueur des suspentes
D³ogoœci i rodzaj poszczególnych linek Sumaryczna d³ugoœæ linek
a b c d br a b c d br
1 2685 2670 2685 2715 1185 1 6775 6695 6800 6970 7705
2 2615 2605 2615 2640 1015 2 6705 6630 6730 6900 7540
3 2670 2655 2665 2685 935 3 6760 6680 6780 6945 7460
4 2540 2505 2525 2580 1115 4 6760 6680 6770 6930 7370
5 2505 2475 2490 2535 1050 5 6725 6650 6735 6880 7305
6 2555 2530 2540 2570 1080 6 6775 6705 6785 6915 7335
7 2120 2000 1955 2050 1090 7 6695 6655 6720 6820 7260
8 2010 1905 1845 1915 995 8 6580 6560 6610 6680 7160
9 1905 1820 1750 1790 985 9 6480 6475 6515 6560 7150
10 960 10 6275 6240 6245 6285 7140
11 955 11 7135
12 1015 12 7195
13 945 13 7130
14 870 14 7055
15 850 15 7035
16 840 16 7000
17 810 17 6965
18 815 18 6970
A B C D BR
1 4090 4025 4115 4255 1355
2 4220 4175 4245 4340 1090
3 4575 4655 4765 1140
4 1155
5 920
6 895 Technora 7343-090-005:
A B C D BR Technora 7343-140-006:
I 2490
II 2350 Technora 7343-190-024:
III 2585
Technora 7343-280-011:
st1 1335 ST1 4940
st2 1295 Technora 7343-280-018:
st3 1300
st4 1340 brmain 2700 Technora 7343-420-041:
Total suspension lines length, measured from the lower surface of the canopy to the inside edge of the maillon (tolerancy +/- 10 mm)
Length of the lines
Nemo2 - 31_XL
The tables / Tables / Tabele:
The individual lenghts and type of line The total lenghts
La longueur et le type de chaque ligne Longueur des suspentes
D³ogoœci i rodzaj poszczególnych linek Sumaryczna d³ugoœæ linek
a b c d br a b c d br
1 2825 2810 2825 2855 1245 1 7155 7075 7180 7360 8120
2 2755 2740 2755 2780 1070 2 7085 7005 7110 7285 7945
3 2810 2795 2805 2830 985 3 7140 7060 7160 7335 7860
4 2675 2635 2660 2715 1175 4 7145 7060 7155 7320 7770
5 2640 2605 2620 2665 1105 5 7110 7030 7120 7270 7705
6 2685 2660 2670 2705 1135 6 7155 7085 7170 7310 7730
7 2230 2105 2055 2160 1150 7 7075 7035 7100 7200 7655
8 2115 2005 1940 2015 1045 8 6960 6935 6985 7055 7550
9 2005 1915 1840 1885 1035 9 6850 6845 6885 6930 7540
10 1010 10 6635 6595 6600 6645 7530
11 1005 11 7525
12 1070 12 7590
13 995 13 7520
14 915 14 7440
15 895 15 7420
16 885 16 7385
17 850 17 7350
18 855 18 7355
A B C D BR
1 4330 4265 4355 4505 1425
2 4470 4425 4495 4600 1145
3 4845 4930 5045 1200
4 1215
5 970
6 940 Technora 7343-090-005:
A B C D BR Technora 7343-140-006:
I 2615
II 2470 Technora 7343-190-024:
III 2725
Technora 7343-280-011:
st1 1400 ST1 5230
st2 1360 Technora 7343-280-018:
st3 1370
st4 1410 brmain 2850 Technora 7343-420-041:
- number of risers: 4 (with A riser split into A and A')
- trimmers: No
Other informations:
Nemo 2 Standard isersR
A A’ B C D
brake line pulley
for additional brakeline pulley (PPG set)
magneticclasp
brake handle
maillonssteering line
pulleys
carabiner
to speed bar
Slowest speed, minimum sink.Take-off setting
All risers neutral at 490 mm length
Trim speed
Total length measured the maillon (tolerancy +/- mm)risers without s 5
Standard isersR - full speed
Other adjustable or removable or variable device:- Triple Comfort Toggle
A A’ B C D
to the speed bar
Triple Comfort Toggle (TCT)
Addressing different needs of our clients we have created a TCT system - Triple Comfort Toggle, making it possible to have your brake handles in rigid, half-rigid or soft configuration without need to purchase additional handles.
Swivel protects the steering line against twisting
Neodymium magnet of the Easy Keeper
exchangeable insert
slit of the rod
half-rigid PVC tube
rigid plastic rod
The most soft handle is obtained when no insertion is used.
Increased speed and sink
Full speed
speed systemsize 31, 28, 25, 23:A - 340A’ - 340B - 360C - 425D - 490
size 20:A - 380A’ - 380B - 400C - 445D - 490
Total length measured the maillon (tolerancy +/- mm)risers without s 5
- number of risers: 4 (with A riser split into A and A')
- trimmers: yes
Other informations:
Nemo 2 Moto isersR
Slowest speed, minimum sink.Take-off setting
All risers neutral at 490 mm length
Trim speed
pulley
EK magnets
speedsystemhooks
carabineer
trimmer buckle
carabiners suspension point for high hangpoints
steering line
covered swivel
TCT brake handle
exchangeable trimmer strap
Main carabiners low suspension point
speedsystempulleys
ABC A’
ELR(Easy LaunchRiser)
D
Trimmer lock system
CB AC A’ B AA’D D
risers length (with maillons)
row:
Trimmers closed (’0' position)
Minimal speed and minimal sinkTake-off position
Trimmers opened
Increased speed and sink
A - 505 A’ - 505 B - 505 C - 505 D - 505
risers length (with maillons)
row: A - 505A’ - 505B - 505C - 545D - 585
Moto Risers
Moto Risers
B AC A’ C B AA’D D
Full acceleration with closed trimmers: Full acceleration with opened trimmers:
risers length (with maillons) risers length (with maillons)
Full speed, increased sink Full speed, increased sink
row A - 395 A’ - 395 B - 415 C - 460 D - 505
row A - 385 A’ - 385 B - 415 C - 500 D - 585
Components
CANOPY FABRIC
Producer: Dominico Textile co. KOREA
Top surface Top surface LE Bottom surface Ribs
DOKDO DOKDO DOKDO DOKDO
30DMF(WR) 30DMF(WR)-HD45 30DMF(WR) 30DFM
Side coated (polyurethane)
Type of yarn PA 6.6 100%
Rip Stop
41 (+/-1) 45 (+/-1) 41 (+/-1) 41 (+/-1)
warp 2,5 min. 3,5 min. 2,5 min. 2,5 min.
weft 2,5 min. 3,5 min. 2,5 min. 2,5 min.
3 lbs 9 max. 7 max. 9 max. 2 max.
5 lbs 15 max. 13 max. 15 max. 3 max.
10 lbs 25 max. 23 max. 25 max. 10 max.
Break strength warp 35 min. 45 min. 35 min. 35 min.
weft 35 min. 45 min. 35 min. 35 min.
30 max. 24 max. 30 max. -
* at pressure 2000 Pa
Producer: Porcher Sport, Zl des Vallons, 38110 La Tour du Pin Cedex, France
Reinforcements Hem
SR-Scrim SR-Laminate
2420 6382
Double laminated
with
polyester films
Laminated with
polyester films
Type of yarn Polyester 550 Dtex Polyester 167 Dtex
- Toile
180 (+/-10) 180 (+/-10)
warp 2,5 min. 0,4 min.
weft 2,5 min. 0,7 min.
3 lbs - -
5 lbs - -
10 lbs - -
Break strength
[dan/5cm] warp 110 min. 110 min.
weft 110 min. 80 min.
- -
* at pressure 2000 Pa
SUSPENSION LINES
Name Symbol Diameter [mm] Weight [g/m]Breaking strength
[daN]Elongation
Aramid Technora** A-7343-090 1,2 1,08 90 0,6%2
Aramid Technora** A-7343-140 1,3 1,34 140 0,4%2
Aramid Technora** A-7343-190 1,5 1,81 190 0,4%2
Aramid Technora** A-7343-280 1,8 2,59 280 0,3%2
Aramid Technora** A-7343-420 2,3 3,98 420 0,2%2
** Producer: Edelmann+Ridder, Achener Weg 66, D-88316 Isny im Allgau, Germany2 elongation at 12 kg
Elongation [%]
Tear Strength [daN]
Coated fabric's weight [g/m2]
Pattern
Type of finish
Code
Name
Usage
Air porosity [l/m2/min]*
Air porosity [l/m2/min]*
Coated fabric's weight [g/m2]
Tear Strength [daN]
Elongation [%]
Type of finish
Pattern
Usage
Name
Code
RISERS
Producer: “PASAMON” Sp. z o.o., ul. Jagielloñska 117, 85-027 Bydgoszcz, Polska
Symbol TE 216/20
Width [mm] 20
Thickness [mm] 2,1
Weight [g/m] 37,2
Breaking strength [daN] 1200
Elongation at breaking [%] 30
Bridle (attachement points)
Producer: Guth & Wolf GmbH, Postfach 1751, 33247 Gutersloh, Germany
Name 57 501/12,50mm c1 000 v01
Width [mm] 12,5 +/- 0,8
Thickness [mm] 0,38-0,64
Weight [g/m] 4,65 max.
Max breaking strength [daN] 112 min.
Elongation at break [%] 18 min.
THREADS
Producer: Coats Polska Sp. z o.o., ul. Kaczeñcowa 16, 91-214 £ódŸ, Poland
Name Gral 60 Gral 40 Gral 20
Material Poliester Poliester Poliester
Tex 40 75 136
Thickness [dtex] 150x3 226x3 455x3
Breaking strength [cN] 2800 4400 8770
Elongation [%] 15-20 15-21 18-25
METAL PARTS
MAILLONS & SQUARES
Producer: PEGUET SA, Zl du Mont Blanc - BP 205, F-74105 Annemasse, France
Symbol D 3,5i
Diameter [mm] 25
Weight [g] 9,5
Quality Inox
Working load limit [kg] 150
Breaking strength [kg] 750
PULLEYS
Producer: AustriAlpin Vertriebs GmbH, A 6166 Fulpmes - Industriezone C10, Austria
Symbol Length [mm] Weight [g]
FL33A 25 5
FL12A 25 9,5
HOOKS
Producer: Finsterwalder – Charly, Pagodenburgstr. 8, D-81247 Munich, Germany
Symbol Length [mm] Load [kg]
Be 180 25 230
OTHER
Producer: Sow-Yacht, 80-292 Gdañsk, ul. Planetarna 9, Poland
Name Rectangle link 20/4
Dimensions [mm] 20x15
Diameter [mm] 4,0
Quality Inox
Weight [g/m] 9,0
Max breaking strength [kg] 900