Upload
purgedsoul
View
1.289
Download
52
Tags:
Embed Size (px)
DESCRIPTION
Training presentation for NEC PASOLINK
Citation preview
PASOLINK FAMILYPASOLINK FAMILY
16x2MB
37-4024.2-2721.2-23.617.7-19.714.2-15.312.7-13.210.7-11.77.1-8.53.6-7.1INTERFACEMODULATIONSYSTEMSERIES/MODEL
STM-12x10/100Base-T
128QAM+RSSDH(STM-1)
11GHz
8x2MB16QAM + RSPDH
STM-12x10/100Base-T
128QAM+RSSDH(2xSTM-1)
STM-12x10/100Base-T
32QAM +RSSDH(STM-1)
21x2MB(STM-1)
32QAM+RSSDH(STM-0)
1 x 34MB
PASOLINK+
2x2MB4x2MB8x2MB16x2MB
(2x10/100Base-T)
4PSKPDHPASOLINK V4
2x2MB4x2MB8x2MB16x2MB1x8MB1x34MB
4PSKPDHPASOLINK V3
38GHz26GHz23GHz18GHz15GHz13GHz7/8GHz4/6GHz
XPIC
System OverviewSystem OverviewNEC has developed the PASOLINK NEO, a narrow band point-to-point digital microwave relay system operating at radio frequency (RF) bands of 6/7/8/11/13/15/18/23/26/28/32/38/52 GHz6/7/8/11/13/15/18/23/26/28/32/38/52 GHz.
The PASOLINK NEO system provides interface types of PDH, SDH and LAN. The transmission signals are 5 to 48 x E1, 1 to 2 x E3, 1 to 2 x STM5 to 48 x E1, 1 to 2 x E3, 1 to 2 x STM--1, 2/4 x 10/100 Base1, 2/4 x 10/100 Base--T(X) T(X) and GbE signals.and GbE signals.
The systems consist of antennas, outdoor unit (ODU) and Indoor unit (IDU) same as PASOLINK series. They are connected through a coaxial cable for each radio channel. Available configurations are non protected type (1+0) and protected type (1+1). The protected type is available for twin-path type and hot-standby type.
System CompositionSystem Composition• 1- Indoor unit (IDU) ( Modulation-Demodulation unit) • 2- Outdoor unit (ODU) ( Transmit – Receive unit)• 3- IF cable and connectors ( To connect the IDU & ODU)• 4- Antenna on the required microwave band• 5- Hybrid ( coupler ) in case of 1+1 one antenna configuration• 6- RF cable ( If the ODU is not direct mounted to the antenna)
MODEM
TX/RX
IF
RF
IDU
Base Band MODEM
TX/RX
IF
RF
IDU
Base Band
ODU (High band)
Antenna Antenna
ODU (low band)TX
RX TX
RX
System Configuration
A- Non protected system (1+0)
IDU ( 1+0 )
ODU IDU ( 1+0 )
ODU
TX
TX
RX
RX
B- Protected system (1+1) hot standbySingle antenna configuration
Modem-1Switch
Modem-2
ODU-1
ODU-2
HModem-1
SwitchModem-2
ODU-1
ODU-2
H
TX
TX
RX
RX
TX/RX TX/RX
Rx only Rx only
System ConfigurationC- Protected system (1+1) hot standby –Space diversity
Double antenna configuration
D- Protected system (1+1) Twin path –Frequency diversity
Modem-1Switch
Modem-2
ODU-1
ODU-2
Modem-1Switch
Modem-2
ODU-1
ODU-2
TX RX
TX/RX TX/RX
Rx only Rx only
RX
TXRX
RX
Modem-1Switch
Modem-2
ODU-1
ODU-2
Modem-1Switch
Modem-2
ODU-1
ODU-2
TX RX
TX/RX TX/RX
Rx only Rx onlyRX
TXRX
RX
TX
TX
PASOLINK NEOPASOLINK NEO
Bit rate Free: 5/10/16/20/40/48E1, STM-1/2xSTM-1Modulation Free : 4PSK,16/32/128QAMFlexible Interface : PDH/SDH/LAN
Equipment Features1. Advanced Technologies and Superb Performance
• High reliability and Quality.• Excellent field proven MTBF.• Low power consumption.• 10 Base-T/100 Base-TX, 1000 Base-SX, 1000 Base-T (LAN interface).• APS for STM-1 optical.• VLAN implementation.
2. High System Gain / High spectrum efficiency
• High System Gain achieved by each modulation with Forward Error Correction(FEC) Technology and distortion canceling technique called linearizer.
• High spectrum efficiency achieved by QPSK to 128QAM selectable technology.• Allowing smaller antennas and reducing system cost.
3. Easy and Quick Installation
• IDU - ODU Interconnection : Only one coaxial cable and automatic equalization.• Very Compact and Light.• Various mounting methods for IDU, ODU and Antenna.• Easy Antenna direction adjustment.
Equipment Features4. Frequency Agility and Easy Tuning
• Field tunable local oscillator (Synthesizer)• RF point frequency can be changed through Local Craft Terminal (LCT).• Sub-band of type is changeable by replacing RF Filter.
5. System Flexibility
• (1+0) Non-protected or (1+1) Protected.• 1+1 Hot Standby / Space Diversity / Twin Path System available.• IDU is used commonly for 6 - 52 GHz.• Changeable data transmission rate (4 to 48x2 Mbps, 1 to 2x34 Mbps, 155 Mbps,
2x155 Mbps, 10/100 Base-T(X), 1000 Base-SX, 1000 Base-T) at the same IDU.• Software settable Modulation (QPSK/16QAM/32QAM/128QAM) of IDU.• Common ODU for PDH/SDH/LAN.• Wide Input Line Voltage range is -40.5 to -57Vdc.
6. Maintenance Facilities
• Local and remote supervision function on IDU through LCT or PNMTj• Full front access at IDU for all cabling and user interface• Loop back facility Near end base band, Far end base band IF loop back• Pre-settable BER alarm point: 10-3, 10-4 or 10-5
Equipment FeatureEquipment Feature7. Service Channels
• Engineering Order Wire (OW): IDU- IDU and Party line.
• SC1 & SC 2: V.11, 64 Kbps Contra-Co directional : Selectable • SC3 & SC 4: RS232C , 9.6 Kbps• SC LAN : SC LAN Sub-Interface ( In case of 155 MB Capacity )
64/128/192/265 Kbps or 2 Mbps Throughput.
• SV Channel commonality:
SV CommonalitySV Commonality
For Nodal Solution
BasebandBaseband Interface FlexibilityInterface Flexibility
5/10/16E1 + 2Ether4Ether + 4E1
40/48E1STM-1(elec.) STM-1(opt.)
Bitrate Free• 5/10/20/40/48E1• STM-1• STM-2(310MB)
Modulation Free• 4PSK,16/32/128QAM
ODU
Interface Board
IDU
SDH ADD/DROP INTFCPDH DIST CARD(PDH Distribution Card)
5E1 10E1 16E1Upgrade Key
40E1 48E1Upgrade Key
ODU
ODU
ODU
V
H
ODU
ODU
ODU
ODU
ODU ODU
Repeater
1+1
1+0
New INTF+Upgrade Key
New INTF+Upgrade Key
New IDU/ODU+Upgrade Key
New MODEMNew ODU
New MODEMNew INTF
+New ODU+Upgrade Key
STM-1
System Upgradeability
2xSTM-1/XPIC
Memory CardMemory Card
APS (Automatic Protection Switching)APS (Automatic Protection Switching)
STM-1 OPT INTFC (W)
STM-1 OPT INTFC (P)
STM-1 OPT INTFC (W)
STM-1 OPT INTFC (P)
STM-1 OPT INTFC (W)
STM-1 OPT INTFC (P)
STM-1 OPT INTFC (W)
STM-1 OPT INTFC (P)
SDH PASOLINK NEOSDH MUX
Working Line
Working Line
Protection Line
Protection Line
Cross Polarization Interference Canceller Cross Polarization Interference Canceller (XPIC)(XPIC)
The transmission capacity of the existing STM-1 equipment can be improved up to 2xSTM-1 by adding one more IDU, ODU and XPIC cable kit and additional firmware.
ODU 1
IDU
OMT
IDU
ODU 2
ODU 1
IDU
OMT
IDU
ODU 2
V
H
V
H
Switchover ControlSwitchover Control
•• Switchover Modes:Switchover Modes:
1.1. Automatic Switchover:Automatic Switchover:Switching is automatically initiated if any failure or abnormality was detected in the online section.
2.2. Manual Switchover:Manual Switchover:The operator initiate this switchover by LCT or PNMT for the maintenance and test purposes. The manual switching has two selection Manual or Forced switchover.
•• Switching Priority:Switching Priority:The switching priority is only applied under automatic switching control.
System Performance Parameters System Performance Parameters QPSKQPSK
Above value with Above value with --1.5 dB1.5 dBBER = 10BER = 10--33
--8484--87.587.5--87.587.5--8989--8989--89.589.5--89.589.5--89.589.5--8989--8989--90907 MHz
--8181--84.584.5--84.584.5--8686--8686--86.586.5--86.586.5--86.586.5--8686--8686--878714 (13.75) MHz
--7878--81.581.5--81.581.5--8383--8383--83.583.5--83.583.5--83.583.5--8383--8383--8484CS = 28 (27.5) MHzCS = 28 (27.5) MHz
Threshold Level Threshold Level ((dBmdBm measured at Antenna port) measured at Antenna port) BER = 10 BER = 10 --66
±± 6 6 ppmppmFrequency Stability
0 to 10 0 to 10 dBdB0 to 25 dB0 to 25 dB0 to 30 dB0 to 30 dBPower Control
+ 3+ 3+18+18+22+22+23+23+23+23+24+24+24+24+23+23+25+25+25+25+29+29Output Power, dBm
PBR 320PBR 320
37.037.0--40.040.0
38
N/AN/A
51.451.4--52.652.6
52
NEC OriginalNEC OriginalN/AN/ARF Direct Mount
PBR 320PBR 320PBR 320PBR 320PBR 260PBR 260PBR 220PBR 220PBR 220PBR 220PBR140PBR140PBR120PBR120PDR100PDR100N Type or N Type or PDR 84PDR 84
N Type or N Type or PDR 70PDR 70RF Remote Mount
31.831.8--33.433.4
27.527.5--29.529.5
24.2524.25--27.027.0
21.221.2--23.623.6
17.717.7--19.719.7
14.214.2--15.3515.35
12.7512.75--13.2513.25
10.710.7--11.711.7
7.1257.125--8.58.5
5.9255.925--7.1257.125
Range ( GHz )
32282623181513117 - 86Frequency Band, ( GHz )
System Performance Parameters System Performance Parameters QPSKQPSK
Less than 10Less than 10--1212 at RSL = at RSL = --30 30 dBmdBmResidual BERResidual BER
--15 dBm (No Error)15 dBm (No Error)Maximum InputMaximum InputLevel dBmLevel dBm
818199.599.5103.5103.5106106106106107.5107.5107.5107.5106.5106.5108108108108113113CS = 28 (27.5) MHzCS = 28 (27.5) MHz
8484102.5102.5106.5106.5109109109109110.5110.5110.5110.5109.5109.511111111111111611614 (13.75) MHz
8787105.5105.5109.5109.5114114114114113.5113.5113.5113.5112.5112.51141141141141191197 MHz
Above value with +1.5 dBAbove value with +1.5 dBBER = 10BER = 10--33
38 52
System Gain System Gain ((dBmdBm measured at Antenna port) measured at Antenna port) BER = 10 BER = 10 --66
32282623181513117 - 86Frequency Band, ( GHz )
System Performance Parameters System Performance Parameters 16QAM16QAM
929294.594.59797979798.598.598.598.598.598.5100.5100.5100100
898991.591.59494949495.595.595.595.595.595.597.597.59797
10510514 (13.75) MHz14 (13.75) MHz
102102CS = 28 (27.5) MHzCS = 28 (27.5) MHz
System Gain (System Gain (dBmdBm measured at Antenna port) measured at Antenna port) BER = 10 BER = 10 --66
Above value with +1.5 dBAbove value with +1.5 dBBER = 10BER = 10--33--83.583.5--83.583.5--8585--8585--85.585.5--85.585.5--85.585.5--8585--8585--86863.5 MHz3.5 MHz
--80.580.5--80.580.5--8282--8282--82.582.5--82.582.5--82.582.5--8282--8282--83837 MHz7 MHz
--77.577.5--77.577.5--7979--7979--79.579.5--79.579.5--79.579.5--7979--7979--808014 (13.75) MHz14 (13.75) MHz
NEC OriginalNEC OriginalN/AN/ARF Direct Mount
PBR 320PBR 320PBR 320PBR 320PBR 320PBR 320PBR 260PBR 260PBR 220PBR 220PBR 220PBR 220PBR 140PBR 140PBR 120PBR 120PDR 100PDR 100N Type or N Type or PDR 84PDR 84
N Type or N Type or PDR 70PDR 70RF Remote Mount
--74.574.5--74.574.5--7676--7676--76.576.5--76.576.5--76.576.5--7676--7676-- 7777CS = 28 (27.5) MHzCS = 28 (27.5) MHz
Threshold Level (Threshold Level (dBmdBm measured at Antenna port) measured at Antenna port) BER = 10 BER = 10 --66
±± 6 6 ppmppmFrequency Stability
0 to 24 dB, in 1 dB step variable0 to 24 dB, in 1 dB step variablePower Control
+13.5+13.5
37.037.0--40.040.0
38
+17+17+18+18+18+18+19+19+19+19+21+21+21+21+21+21+25+25Output Power, dBm
31.831.8--33.433.4
27.527.5--29.529.5
24.2524.25--27.027.0
21.221.2--23.623.6
17.717.7--19.719.7
14.214.2--15.3515.35
12.7512.75--13.2513.25
10.710.7--11.711.7
7.1257.125--8.58.5
5.9255.925--7.1257.125
Range ( GHz )
32282623181513117 - 86Frequency Band, ( GHz )
System Performance Parameters System Performance Parameters 16QAM16QAM
Less than 10Less than 10--1212 at RSL = at RSL = --30 30 dBmdBmResidual BERResidual BER
--20 dBm for the BER less than 1020 dBm for the BER less than 10--33Maximum InputMaximum InputLevel dBmLevel dBm
959597.597.5100100100100101.5101.5101.5101.5101.5101.5103.5103.5103103108108CS = 7 MHzCS = 7 MHz
9898100.5100.5103103103103104.5104.5104.5104.5104.5104.5106.5106.51061061111113.5 MHz
Above value with +1.5 dBAbove value with +1.5 dBBER = 10BER = 10--33
3832282623181513117 - 86Frequency Band, ( GHz )
System Performance Parameters System Performance Parameters 32 QAM32 QAM
Less than 10Less than 10--12 12 at RSL = at RSL = --30 30 dBmdBmResidual BERResidual BER
--20 20 dBmdBm for the BER less than 10for the BER less than 10--33Maximum InputMaximum InputLevel dBmLevel dBm
Above value with +1.5 dBAbove value with +1.5 dBBER = 10BER = 10--33
66.566.587.587.5909092.592.592.592.594949494969695.595.595.595.5100.5100.5CS = 28 (27.5) MHzCS = 28 (27.5) MHz
System Gain System Gain ((dBmdBm measured at Antenna port) measured at Antenna port) BER = 10 BER = 10 --66
Above value with Above value with --1.5 dB1.5 dBBER = 10BER = 10--33
--69.569.5--7373--7373--74.574.5--74.574.5--7575--7575--7575--74.574.5--74.574.5--75.575.5CS = 28 (27.5) MHzCS = 28 (27.5) MHz
Threshold Level Threshold Level ((dBmdBm measured at Antenna port) measured at Antenna port) BER = 10 BER = 10 --66
±± 6 6 ppmppmFrequency Stability
0 to 6 dB0 to 6 dB0 to 30 dB0 to 30 dBPower Control
--33+14.5+14.5+17+17+18+18+18+18+19+19+19+19+21+21+21+21+21+21+25+25Output Power, dBm
PBR 320PBR 320
37.037.0--40.040.0
38
N/AN/A
51.451.4--52.652.6
52
NEC OriginalNEC OriginalN/AN/ARF Direct Mount
PBR 320PBR 320PBR 320PBR 320PBR 260PBR 260PBR 220PBR 220PBR 220PBR 220PBR140PBR140PBR120PBR120PDR100PDR100N Type or N Type or PDR 84PDR 84
N Type or N Type or PDR 70PDR 70RF Remote Mount
31.831.8--33.433.4
27.527.5--29.529.5
24.2524.25--27.027.0
21.221.2--23.623.6
17.717.7--19.719.7
14.214.2--15.3515.35
12.7512.75--13.2513.25
10.710.7--11.711.7
7.1257.125--8.58.5
5.9255.925--7.1257.125
Range ( GHz )
32282623181513117 - 86Frequency Band, ( GHz )
System Performance Parameters System Performance Parameters 128 QAM128 QAM
NEC OriginalNEC OriginalN/AN/ARF Direct Mount
PBR 320PBR 320PBR 320PBR 320PBR 320PBR 320PBR 260PBR 260PBR 220PBR 220PBR 220PBR 220PBR 140PBR 140PBR 120PBR 120PDR 100PDR 100N Type or N Type or PDR 84PDR 84
N Type or N Type or PDR 70PDR 70RF Remote Mount
Less than 10Less than 10--12 at RSL = 12 at RSL = --30 30 dBmdBmResidual BERResidual BER
--20 dBm for the BER less than 1020 dBm for the BER less than 10--33Maximum InputMaximum InputLevel dBmLevel dBm
Above value with +1.5 dBAbove value with +1.5 dBBER = 10BER = 10--33
81.581.5848486.586.586.586.588888888909089.589.589.589.594.594.5CS = 28 (27.5) MHzCS = 28 (27.5) MHz
System Gain System Gain ((dBmdBm measured at Antenna port) measured at Antenna port) BER = 10 BER = 10 --66
Above value with Above value with --1.5 dB1.5 dBBER = 10BER = 10--33
--6767--6767--68.568.5--68.568.5--6969--6969--6969--68.568.5--68.568.5-- 69.569.5CS = 28 (27.5) MHzCS = 28 (27.5) MHz
Threshold Level (Threshold Level (dBmdBm measured at Antenna port) measured at Antenna port) BER = 10 BER = 10 --66
±± 6 6 ppmppmFrequency Stability
0 to 20 dB, in 1 dB step variable0 to 20 dB, in 1 dB step variablePower Control
+14.5+14.5
37.037.0--40.040.0
38
+17+17+18+18+18+18+19+19+19+19+21+21+21+21+21+21+25+25+25+25Output Power, dBm
31.831.8--33.433.4
27.527.5--29.529.5
24.2524.25--27.027.0
21.221.2--23.623.6
17.717.7--19.719.7
14.214.2--15.3515.35
12.7512.75--13.2513.25
10.710.7--11.711.7
7.1257.125--8.58.5
5.9255.925--7.1257.125
Range ( GHz )
32282623181513117 - 86Frequency Band, ( GHz )
IDU Performance Parameters(1/2)IDU Performance Parameters(1/2)
PMON Items;a) OFS, b) BBE, c) ES, d) SES, e)SEP, f) UAS
PMONPMON
Manual Control, Automatic Control and Mute Control.TX Output ControlTX Output Control
Direct entry or Table Download entry :AvailableFrequency ChangingFrequency Changing
Adjustable 10-3/ 10-4/ 10-5BER ALMBER ALM77
Near End, Far End Baseband Loop Back and IF Loop BackLoop BackLoop Back66
2 levelsLCT Security LevelsLCT Security Levels55
V.11(Contra/Co-directional) x 2 channels,RS-232 x 2 channelsService ChannelsService Channels44
10/20/40/80/100/100+50/, 75+75 Mbps
155/ 2x155 Mbps
34/68 Mbps8/16/32/64/96Mbps
Total CapacityTotal Capacity
2/41/21/24/8/16/32/48Channel NumberChannel Number
10/100 Base-T(X)1000 Base-SX1000 Base-T
STM-1 :155.52 Mbps ± 20 ppm
E3:34.368Mbps±20 ppm
E1:2.048 Mbps ± 50 ppm
Baseband InterfaceBaseband Interface33
QPSK/16/32/QAM128 QAM128 QAMQPSK/16/32/QAMModulation Type21+0 Expandable / 1+11+0 Expandable / 1+1IDU Type1
LANSDHPDH
SPECIFICATIONItemNo.
IDU Performance Parameters(2/2)IDU Performance Parameters(2/2)
・Module alarm (Red)LAN/WS INTFC
・Module alarm (Red)・Online (Green) for APS only
SD INTFC・Module alarm (Red)PDH INTFC
・Operating PWR (Green)・ODU Alarm (Red)・MD/CBL Alarm (Red)・TX status (Green)・RX status (Green)・XPIC Reset (Yellow) for XPIC only
MODEM
・IDU Alarm (Red)・Maintenance (Yellow)・Memory Access (Yellow)
CTRLLED DisplayLED Display88
LAN monitoring Items;a) RX Unicast, b) RX Broadcast, c) RX Multicast, b) d) RX Pause, e) RX CRC error
Metering Itemsa) Output power level (TX PWR), b) Received signal level (AGC V)c) Bit error rate (BER MON)
PMONLANSDHPDH
SPECIFICATIONItemNo.
Interconnection between IDU & ODUInterconnection between IDU & ODU
33oC to +50oC (workable : -40oC to +55oC)Guaranteed temperature range6
Automatic level equalizationCable Equalization5
150 m (5D-FB)300 m (8D-FB)350 m (10D-FB)
Maximum Cable Length4
IF signal, alarms, control, monitoring andpower source
Signals3
5D-FB, 8D-FB (standard)10D-FB
Standard Type of CableIF cable adapter
2
Single Coaxial Cable per system / 50 ohmsInterconnection1
SPECIFICATIONItemNo.
Alarm output ItemsAlarm output Items
IDUHIGH BER ALM19
IDUIDU ALM18
IDU/MD CBL BlinkingIF CABLE SHORT ALM217
IF CABLE SHORT ALM116
ODU
RX LEV ALM215
RX LEV ALM114
ODU
APC ALM213
APC ALM112
ODU
TX IN ALM211
TX IN ALM110
ODU
TX PWR ALM29
TX PWR ALM18
ODU Blinking
ODU CPU ALM27
ODU CPU ALM16
ODU
ODU ALM25
ODU ALM14
--IDU CPU ALM3
PWRPS ALM2
MAINTMAINT1
RL6RL5RL4RL3RL2RL1
Relay Alarm OutputALM IndicationAlarm Item on LCT/PNMTNo.
House keeping output ItemsHouse keeping output Items
PNMT onlyCluster ALM Out48
PNMT onlyCluster ALM Out37
PNMT onlyCluster ALM Out26
PNMT onlyCluster ALM Out15
PNMT onlyHK-OUT44
PNMT onlyHK-OUT33
PNMT onlyHK-OUT22
PNMT onlyHK OUT11
RL6RL5RL4RL3RL2RL1
Relay Alarm OutputALM IndicationAlarm Item on LCT/PNMTNo.
The Factory setting
The HK that cane be configured
The relays RL1 & RL2 can’t be changed
Notes:
House keeping Input ItemsHouse keeping Input Items
PNMT onlyCluster ALM Input410
PNMT onlyCluster ALM Input39
PNMT onlyCluster ALM Input28
PNMT onlyCluster ALM Input17
PNMT onlyHK-IN66
PNMT onlyHK-IN55
PNMT onlyHK-IN44
PNMT onlyHK-IN33
PNMT onlyHK-IN22
PNMT onlyHK-IN11
IN6IN5IN4IN3IN2IN1
Relay Alarm OutputEvent IndicationAlarm Item on LCT/PNMTNo.
PASOLINK NEO IDU PASOLINK NEO IDU
PASOLINK NEO IDU ( 1+0 )PASOLINK NEO IDU ( 1+0 )
PASOLINK NEO IDU ( 1+1 )PASOLINK NEO IDU ( 1+1 )
IDU CompositionIDU Composition
IDU Shelf :IDU Shelf :
IDU ModulesIDU Modules
H2950 CTRL7
PDH-E3 e/w 4/8E1, 2 Port LANH3010 E2 INTFC
PDH-48 E1H3000 48E1 INTFC
PDH-16E1 e/w 2 Port LANH2980 16E1 INTFC
6
WS-SC-LAN/WS/SC-LANH2965 LAN/WS INTFC
STM1-E/O-S-1.1/L-S-1.1 for APSH2960 STM-1 INTFC5
SDH-GbEH3021 GbE INTFC
SDH 2-Port-LANH2965 LAN/WS INTFC
STM1-E/O-S-1.1/L-S-1.1H2960 STM-1 INTFC
4
-20 to –60 VDC H3040 DC-DC CONV
H2940 MODEM3
QPSK/16QAM/32QAM/128QAMH2940 MODEM2
H2931 RACK1
1+1 1+1 SystemSystem
1+01+0ExpandableExpandable
RemarksRemarks
H2930 MDPH2930 MDP--150MB150MB--1AA1AA
UNIT/MODULE NAMEUNIT/MODULE NAMENo.No.
Usually Provided
Optionally provided
Base Band InterfaceBase Band Interface
-Blank PanelNOT USED
155 MbpsService Channel LAN for STM-1SC LAN
155 MbpsWS (E1)WS
155 MbpsWS (E1) and WC/Service Channel LAN for STM-1WS-SC LANSub Sub InterfaceInterface
80 MbpsPDH-1E3 2xE3 (34 Mbps) interface 80 MbpsPDH-2E3
40 MbpsPDH-1E3 1xE3 (34 Mbps) interface 40 MbpsPDH-1E3
108 MbpsPDH-4P-LAN 4 port LAN only for 32QAM 100 Mbps PDH-4P-LAN
80 -108 MbpsPDH-48E1 48E1 (MDR 75/120 ohm selectable) PDH-48E1
10 - 80 MbpsPDH-16E1 16E1 + 2 port LAN (D-sub 75/120 ohm selectablePDH-16E1
155 MbpsSDH-GBE 1000 Base-T (RJ-45) or 1000 Base-SX (LC)SDH-GBE
155 MbpsSDH-2P-LAN 2 port 10/100 Base-T(X)SDH-2P-LAN
155 MbpsSTM1-O-L11 STM-1 Optical L-1.1 (connector type LC) STM1-O-L11
155 MbpsSTM1-O-S11 STM-1 Optical S-1.1 (connector type LC) STM1-O-S11
155 MbpsSTM1-E STM-1 Electrical (IEC 1.0/2.3 coaxial) STM1-EMain Main InterfaceInterface
Available CapacityAvailable CapacityPanel DetailsPanel DetailsParametersParametersItemItem
Baseband InterfaceBaseband Interface
BaseBandBaseBand InterfaceInterface
up to 48 E1 signals2.048 Mbps +/- 102.4 bpsHDB375 ohms unbalanced or 120 ohms balanced
Input/Output Signals:Bit Rate:Code:Impedance:
16 E1 interface in each connector2M IN/OUT-A/-B/-C( MDR Connector )
48 E1 Interface48 E1 Interface
BaseBandBaseBand InterfaceInterface 16 E1 Interface16 E1 Interface
LAN interface port 1 and port 2 are separated. 8 to 40 Mbps shared when 16 E1 to 0E1 are used.10/100 base-T(X) Auto sensing or fixedFull duplex or Half duplexStore and Forward
PORT 1/PORT 2 (RJ-45)
up to 48 E1 signals2.048 Mbps +/- 102.4 bpsHDB375 ohms unbalanced or 120 ohms balanced
Input/Output Signals:Bit Rate:Code:Impedance:
8 E1 interface in each connector.2M IN/OUT-A/-B/-C
BaseBandBaseBand InterfaceInterface 16 E1 Interface16 E1 Interface
BaseBandBaseBand InterfaceInterface
Optical STM-1 INPUT/OUTPUT, G.957155.520 MbpsNRZ1310 nmL-1.1: 0 to -8 dBm (TX) / -10 to -34 dBm (RX)S-1.1: -8 to -15 dBm (TX) / -8 to -28 dBm (RX)
STM-1 IN/OUT LCType:Rate:Code:Wavelength:Level:
STMSTM--1 Interface1 InterfaceSTM-1 Electrical Interface
STM-1 Optical Interface
Electrical STM-1 PUT/OUTPUT,
G.703155.520 Mbps1 Vp-pCMI75 ohms, unbalanced
STM-1 IN/OUT IEC 169-13
Type:Rate:Level:Code:Impedance
ALM: To indicate any ALM action occurred in the InterfaceLOS of STM-1 detected from the DTE or from DMR.Frame Synchronization of input signal is lostBER is worse than ( 10-3~10-5 selectable ) DMR or MUXBER is worse than ( 10-5 ~ 10-9 selectable ) DMR or MUXMounted module is not matched with the inventory
Working in APS: ONLINE ONSYANDBY APS: ONLINE OFFNO APS: ONLINE OFF
MODEM UnitMODEM Unit
The MODEM provides the QPSK/16QAM/32QAM/128QAM Modulation and Demodulation for E1/E3 (PDH), 10/100 base-T (LAN), or STM-1 (SDH) data transmission in addition to the following main functions:
Forward Error Correction using RS/Interleaving.XPIC ODU Synthesizer synchronization control.Interfered signal from opposite polarization cancellation ( XPIC ).IDU/ODU Power Supply.System Power On/Off.
Interfaces/Switches/Indications
To indicate any alarm occurred at ODU Circuit.ODU
XPIC function is off conditionXPIC RESET
Selected status of MDOEM RX output signalRX (only 1+1 )
Selected status of ODU TXTX ( only 1+1 )
Blinks when IF cable is short circuit.MD/CBL
To indicate the power switch of the MODEM is turned on.PWR
IDU/ODU Turn Power onPWR Switch
Tx Frequency: 340 MHzRx Frequency: 140 MHzImpedance : 50 ohmsConnecting IF Cable length: 5D-FB: less than 150 m
10D-FB: less than 300 m12D-FB: less than 350 m
IF IN/OUT
Ground Terminal( 5mm2 cable)G
( MOLEX M5557-4R, 4pins) , ( DC IN)-48VDC(negative ) , + (positive, Ground)
SEL V
( D-SUB 15 pins) Serial PortOnly used for XPIC system between two IDUs.
XPIC CTRL
Only used for XPIC systemIF Signal of opposite polarization.IF Signal for opposite polarization output.140 MHz75 ohms
XIF IN/XIF OUT
Power SupplyPower Supply
Power SupplyPower Supply
When the ODU which connected is not NEO connected to IDU NEO, it is recommended to install the optional DC-DC CONV into the IDU.
The ODU will be shorten ODUs life or may be damaged if not used optional DC-DC CONV module.
CTRL UnitCTRL Unit
Back to Back Back to Back ConnectionConnection10 Base10 Base--TTRJRJ--4545
NENE
PNMS InterfacePNMS Interface10 Base10 Base--TTRJRJ--4545
NMSNMS
LCT and PNMT LCT and PNMT InterfaceInterfaceUSB 1.1USB 1.1Connector Type BConnector Type B
LCTLCT
EOW input 1 (+)EOW input 1 (+) 11 1616 EOW input 1 (EOW input 1 (--))EOW output 1 (+)EOW output 1 (+) 22 1717 EOW output 1 (EOW output 1 (--))
EOW output 2 (+)EOW output 2 (+) 44 1919 EOW output 2 (EOW output 2 (--))EOW input 2 (+)EOW input 2 (+) 33 1818 EOW input 2 (EOW input 2 (--))
GroundGround 55RL 6 ( NO )RL 6 ( NO ) 66 2020 RL 6 ( COM )RL 6 ( COM )
RL 4 ( NO )RL 4 ( NO ) 88 2222 RL 4 ( COM )RL 4 ( COM )RL 5 ( NO )RL 5 ( NO ) 77 2121 RL 5 ( COM )RL 5 ( COM )
RL 3 ( NO )RL 3 ( NO ) 99 2323 RL 3 ( COM )RL 3 ( COM )RL 2 ( NO )RL 2 ( NO ) 1010 2424 RL 2 ( COM )RL 2 ( COM )
ALM HK2 IN (+)ALM HK2 IN (+) 1212 2626 HK4/CL3 IN (HK4/CL3 IN (--))RL 1 ( NO )RL 1 ( NO ) 1111 2525 RL 1 ( COM )RL 1 ( COM )
3535
3030 BUZZER input 1BUZZER input 13131 CALL output 1CALL output 1
3333 CALL output 2CALL output 23232 BUZZER input 2BUZZER input 2
34343535 RL 6 ( NC )RL 6 ( NC )3636 RL 5 ( NC )RL 5 ( NC )3737 RL 4 ( NC )RL 4 ( NC )3838 RL 3 ( NC )RL 3 ( NC )
4040 RL 1 ( NC )RL 1 ( NC )3939 RL 2 ( NC )RL 2 ( NC )
4141 HK6/CL1 IN (HK6/CL1 IN (--))4242 HK6/CL1 IN (+)HK6/CL1 IN (+)4343 HK5/CL2 IN (HK5/CL2 IN (--))4444 HK5/CL2 IN (+)HK5/CL2 IN (+)
ALM HK2 IN (ALM HK2 IN (--)) 1313ALM HK1 IN (ALM HK1 IN (--)) 1414ALM HK1 IN (+)ALM HK1 IN (+) 1515
2727 HK4/CL3 IN (+)HK4/CL3 IN (+)2828 HK3/CL4 IN (HK3/CL4 IN (--))2929 HK3/CL4 IN (+)HK3/CL4 IN (+)
AUX/ ALM DAUX/ ALM D--Sub F, 44 pinsSub F, 44 pins
NE2NE2 RS485 ASYNC.RS485 ASYNC.
DSC4DSC4 RS232C 9.6 RS232C 9.6 KbpsKbps
DSC3 DSC3 RS232C 9.6 RS232C 9.6 KbpsKbps
DSC2DSC2 V.11 64 KbpsV.11 64 Kbps
DSC1DSC1 V.11 64 KbpsV.11 64 Kbps
SC IN/OUTSC IN/OUT
Prevent service interruption in case Prevent service interruption in case of CTRL module replacement.of CTRL module replacement.
PROTECTPROTECT
Transmit the EOW calling to sound Transmit the EOW calling to sound the BUZZER in the opposite stationthe BUZZER in the opposite station
CALLCALL
Jack for OW headsetJack for OW headsetEOWEOW
To indicate the maintenanceTo indicate the maintenanceCondition.Condition.
The Memory card is acceptedThe Memory card is accepted
An event occurred on IDU.An event occurred on IDU.
SC IN/OUT DSC IN/OUT D--Sub F, 44 pinsSub F, 44 pins
Outdoor Unit ( 6 - 52 GHz )
Frame Ground
Turn OFF the DC power before removing the IF cable
RX LEV MONITOR • The nominal power supply voltage is -48 V DC. However, the range of the unit is able to fit for nominal voltages of +24 V by additional unit.• The weight of ODU is 3 Kg.
Outdoor Unit ( ODU )
• The transmitter-receiver is designed to handle an 8-155 Mbps digital signal in the 6-52 GHz bands. The equipment is designed to withstand severe weather conditions. To achieve high system gain performance, quadrature phase-shift keying (QPSK) modulation is applied. And to achieve high frequency efficiency performance, 16/32/128-quadrature amplitude modulation (16/32/128QAM) is applied. This ODU can apply to each modulation.
• Advanced integrated circuit technology, e.g., MMIC and MIC, is applied to the entire RF circuit in ODU.
Outdoor UnitOutdoor Unit
Hybrid Combiner
6/7/8 GHz Coupler (N-type) 11 ~ 38 GHz Coupler (N-type)
NEC has developed Hybrid Combiner/Divider over the full range ofNEC has developed Hybrid Combiner/Divider over the full range of microwave frequencies for PASOLINK Series digital microwave microwave frequencies for PASOLINK Series digital microwave radio pointradio point--toto--point fixed wireless systems. This Hybrid Combiner/Divider comprpoint fixed wireless systems. This Hybrid Combiner/Divider comprises directional coupler, antenna interface, radio ises directional coupler, antenna interface, radio mounting interfaces and mounting interfaces and polarizerspolarizers. The RF signal power received by the single polarized antenna i. The RF signal power received by the single polarized antenna is equally distributed and sent to s equally distributed and sent to two outdoor units through the Hybrid Combiner/Divider for 1+1 prtwo outdoor units through the Hybrid Combiner/Divider for 1+1 protected systems.otected systems.There are two types of NEC Hybrid Combiner/Divider, one is coaxiThere are two types of NEC Hybrid Combiner/Divider, one is coaxial cable connection type for 6/7/8 GHz Bands and the other is al cable connection type for 6/7/8 GHz Bands and the other is WG connection type for 11 WG connection type for 11 –– 52 GHz Bands. NEC Hybrid Combiner/Divider is suited for Andrew 52 GHz Bands. NEC Hybrid Combiner/Divider is suited for Andrew or RFS Antenna, and all NEC or RFS Antenna, and all NEC ODUs.ODUs.
10 Coupler
6/7/8 GHz Coupler (N-type) 11 ~ 38 GHz Coupler (N-type)
The RF signal power received by the single polarized antenna is The RF signal power received by the single polarized antenna is unequally distributed to two outdoor units in unequally distributed to two outdoor units in the ratio of 9 to 1 through the 10 dB Coupler for 1+1 protected the ratio of 9 to 1 through the 10 dB Coupler for 1+1 protected systems. Using this 10 dB Coupler, regular systems. Using this 10 dB Coupler, regular side signal level could be kept higher than in using 3 dB equal side signal level could be kept higher than in using 3 dB equal Combiner/Divider.Combiner/Divider.There are two types of NEC 10 dB Coupler; one is coaxial cable cThere are two types of NEC 10 dB Coupler; one is coaxial cable connection type for 6/7/8 GHz bands and the onnection type for 6/7/8 GHz bands and the other is WG connection type for 11 other is WG connection type for 11 -- 38 GHz Bands. NEC 10 dB Coupler is suited for Andrew or RFS 38 GHz Bands. NEC 10 dB Coupler is suited for Andrew or RFS Antenna, and all NEC ODUs.Antenna, and all NEC ODUs.
Ortho Ortho –– Mode Transducer ( OMT )Mode Transducer ( OMT )OMT enables dual polarization feature to double the transmission capacity for the PASOLINKsystem. NEC OMT has Wave Guide connection type for 11-38 GHz Bands, which is suited forRFS Antenna and all NEC ODUs.
The OMT comprises Ortho-Mode transducer, antenna interfaceand radio mounting interfaces.
ODU Mounting ConfigurationsODU Mounting Configurations
Suitable configuration can be selected from various ODU mounting styles:• Direct Mounting on Antenna• Separate Mounting with Antenna using Waveguide or Coaxial Cable• 1+1 system with Hybrid Combiner / Divider• 2+0 system with Dual Polarization Antenna
1+0 System Configuration
11 - 52 GHz Direct Mounting of 1+0 PASOLINK ODU
Antenna
ODU
ODU Mounting ConfigurationsODU Mounting Configurations
11 - 38 GHz Remote Mounting of 1+0 PASOLINK ODU
6/7/8 GHz Remote Mounting of 1+0 PASOLINK ODU
ODU Mounting ConfigurationsODU Mounting Configurations
1+1 System Configuration
11 - 52 GHz Direct Mounting of the 1+1 PASOLINK ODU(One Antenna with Hybrid Combiner unit)
ODU Mounting ConfigurationsODU Mounting Configurations
11 - 38 GHz Remote Mounting of 1+1 PASOLINK ODU with two antennas
11 - 38 GHz Remote Mounting of 1+1 PASOLINK ODUwith Hybrid Combiner
ODU Mounting ConfigurationsODU Mounting Configurations
6/7/8 GHz Remote Mounting of 1+1 PASOLINK ODU with Hybrid Combiner and one antenna
6/7/8 GHz Remote Mounting of 1+1 PASOLINK ODU with two antennas
ODU Mounting ConfigurationsODU Mounting Configurations
2+0 System ConfigurationDual Pol. Antenna System for Adjacent channel orCo-Channel assignment)
6/7/8 GHz Remote Mount Dual Pol. System11 - 38 GHz Remote Mount Dual Pol. System
11 - 38 GHz Direct Mount Dual Pol. System
PASOLINK MONITORPASOLINK MONITOR•Meter – Indicates the Receive level as a dc voltage
•OW Indicator – Lights when the OW-ON/OFF switch is set to ON. Under this condition if the indicator is not lit replace the battery.
•OW ON/OFF SW – when set to ON enables OW communication between the IDU and the ODU.•VOL control – Adjust the level of the OW RX signal.
•Head set Jack – connects the headset for OW communication
•RX LEV/OW IN connector –connect the OW/RX Lev monitor to the ODU using the provided coaxial cable
•Battery – use 6F22(UB) / 9V battery
Loop Back ControlLoop Back Control
(a) STM-1 near-end loopback (STM-1 LB1) at the 150M INTFC/OPT INTFC module(b) STM-1 far-end loopback (STM-1 LB2) at the 150M INTFC/OPT INTFC module from LCT(c) IF loopback (IF-LB) at the MODEM module (Local only)(d) STM-1 far-end loopback (STM-1 LB2) at the 150M INTFC/OPT INTFC Module from PNMT/PNMS
•Note: While the IF loopback is in execution, monitoring of the opposite and the subsequent stations from the PNMS and PNMT are disabled.
(d)
PASOLINK NEO InstallationPASOLINK NEO Installation
Before going to any site,
please be sure you completely prepared the following items:1-The installation tools.2-The test equipment ,materials ,and tools.( for test work only)3-Site installation drawings.4-All labels/stickers (hard and soft copy)5-Frequency plan and system configuration documents.6-Test procedure and test data sheets ( for test work only)7-Confirm access to site/station.8-Check the condition of the vehicle to be used.9-Make sure you and your staff are in good conditions (physically)10-Confirm the site/station entrance conditions. 11-Move to site/station safely.
IF CableConnectionIF Cable
Connection
IDU Grounding ConnectionIDU Grounding Connection
Connect the Power Connect the Power Follow Start up and set up Procedure
Follow The termination Procedure
Follow The termination Procedure IDU
Mounting
19" rack fixing19" rack fixing
Unpacking of 19" rack (if supplied)
Unpacking of 19" rack (if supplied)
IF Connector & Power Connector termination
IF Connector & Power Connector termination
Unpacking of Accessories
Unpacking of Accessories
Unpacking of IDU
Unpacking of IDU
Refer to the IDU fixing Procedure Photos
Rack Earthing Connection
Rack Earthing Connection
Confirm 19" Rack Location& DC-Power Source
1-INDOOR INSTALLATION1-INDOOR INSTALLATION
NESIC CAIRO
UNPACKING IDUUNPACKING IDU
•Open the carton take out the Accessories Carton
•Take out the cushioning materials of the IDU Carton
•Take out the IDU with the antistatic bag from the carton
•Take out the IDU from the antistatic bag•Inspect IDU
IDU MOUNTIDU MOUNTFRONT POSITION
CENTER POSITION
Fix each side of the IDU to the rack with (M5) screws
Align the IDU to the mount position
When mounting the IDU in a 19 inch rack, leave a space of 200mm to the rear section and space of one rack unit to the top and bottom.
More than one rack unit
More than one rack unit
WALL
Mount the two brackets to the IDU with four screws Align the IDU to the center mount position
and fix each side with (M5) screws
CONNECTOR & POWER CABLECONNECTOR & POWER CABLE
Power Connector
Power Cable
Socket Contact
1-Remove 3.0 to 3.5 mm of Insulation
2- Set the socket contact to the following position onto the hand crimping tool
1
Hand Crimping tool (57026-5000)
Position Position . of Cable. of CableiaiaddCrimping TypeCrimping Type5702657026--5000 5000 ФФ 1.5 to 1.8 11.5 to 1.8 1
ФФ 1.8 to 2.2 21.8 to 2.2 25702757027--5000 5000 ФФ 2.3 to 2.6 12.3 to 2.6 1
ФФ 2.6 to 3.1 22.6 to 3.1 2
2
3- Squeeze the handle of the hand crimping tool, insert cable into socket contact
4- Cable should fit, so insulation and bare wire are arranged as shown,
5- Squeeze the handle of the hand crimping tool until ratchet is released.
6- Insert socket contacts to power connector till they locked and be sure it is well fixed.
55--Squeeze the Squeeze the handle of the hand handle of the hand crimping tool until crimping tool until ratchet Is releasedratchet Is released
(0 V)
(-48 V)
NESIC CAIRO
IF CableConnectionIF Cable
Connection
ODU Grounding ConnectionODU Grounding Connection
IF Cable LayingIF Cable LayingConnect to IDU & Follow Start up and set up Procedure
Follow The termination Procedure
Follow The termination Procedure ODU
Mounting
Unpacking of Antenna
Unpacking of Antenna
IF ConnectorIF Connector
Unpacking of Accessories
Unpacking of Accessories
Unpacking of ODU
Unpacking of ODU
Refer to the IDU fixing Procedure Photos
Remove the ODU cover, Confirm the
Polarity
Remove the ODU cover, Confirm the
Polarity
Antenna bracket assembling,
Confirm the Polarity
1-OUTDOOR INSTALLATIONFLOW CHART
1-OUTDOOR INSTALLATIONFLOW CHART
Refer to the Antenna assembling guide
UNPACKING ODUUNPACKING ODU
•Open the carton
•Take out the ODU with cushioning materials
•Remove the cushioning materials from the ODU
•Take out the ODU from the antistatic bag
•Open the carton
•Take out the ODU with the cushioning materials
•Remove the cushioning material from the ODU
•Inspect ODU•Inspect ODU
6/7/8 GHz ODU 11- 38 GHz ODU
POLE MOUNTING BRACKETPOLE MOUNTING BRACKET
New Type Bracket for 11-38 GHz Band ODU Old Type Bracket for 11-38 GHz Band ODU
Bracket for 6/7/8 GHz Band ODU
POLE MOUNTING BRACKETPOLE MOUNTING BRACKET
NEW TYPE BRACKET
NEW TYPE BRACKET
V /H POLARIZATION (1+1)V /H POLARIZATION (1+1)
PROCEDURE FOR SETTING V/H POLARIZATION USING HYBRID
ANTENNA SIDE
•Loosen the four screws with allen keys and rotate the antenna connection unit to the required polarization position•Tighten the four screws.
HYBRID SIDE•The hybrid is set to V-polarization when shipped from the factory
•Rotate the two plates to the position required for the required polarization and fix them in position with the screws
•Remove the two screws.
V - POLARIZATION
H - POLARIZATION
SCREWS
SCREWS
ANTENNA CONNECTION UNIT
SCREWS
Quasar HybridNEC Hybrid
ANTENNA DIRECT MOUNT ANTENNA DIRECT MOUNT –– V/H POLV/H POL
PROCEDURE FOR SETTING V/H POLARIZATION
•When vertical polarization is required, rotate the IDU so that the plate marked with V is pointing up. Fix the ODU in this position
•When horizontal polarization is required, rotate the IDU so that the plate marked with H is pointing up. Fix the ODU in this position
USE OF OUSE OF O--RINGSRINGS
•Do not use both small O-ring and large O-ring simultaneously
•O-ring size is different forf different frequency bands
ODU MOUNTODU MOUNT
Local Craft Terminal (LCT)Local Craft Terminal (LCT)The Local Craft Terminal (LCT) is used to access, setup, manage, monitor and controls the PASOLINK NEO PDH/SDH Microwave Radio system.
Hardware Requirement:
H.D.D: 100MB or higher empty disk capacityRAM: 256 MBDisplay: LCD 1,024 x 768CD-ROM DriveSerial PortUSB PortUSB Cable with USB-B Connector
Software Requirement:
OS: Windows 2000/XP IE6.0 SP2Java Runtime Environment V1.5.0_05 or higher
LCT Setup ProceduresLCT Setup Procedures1. Installation of USB Driver:
LCT Setup ProceduresLCT Setup Procedures2. Dial-up Connection:
LCT Setup ProceduresLCT Setup Procedures2. Dial-up Connection:
LCT Setup ProceduresLCT Setup Procedures2. Dial-up Connection:
LCT Setup ProceduresLCT Setup Procedures1. Installation of Java Run Time:
Java Run Time Environment V1.5.0_05 or higher is required.
LCT OperationLCT OperationConnect to the USB port of IDU using the USB cable
Connect using the dial up connection “LCT”.
Open the Internet Explorer
Enter URL Address: http://172.17.254.253 of the IE and press the “Enter” key.
The login window will then enter your login information User ID and password in the entry field thenpress login
No password
12345678Password
Monitoring onlyUser
Access to the LCT and control
AdminPrivilegeUser ID
LCT OperationLCT OperationDescription of LCT Menu Convections
To execute the commands
To logout from the LCTThen a confirmation Message will appear toConfirm or cancel.
To show the status of Command execution if OKOr no response.
Yellow for MAINT status
LCT Main MenuLCT Main Menu
Equipment Setup MenuEquipment Setup MenuFrom the “User Interface” menu button, you can select PDH E1, PDH with LAN or SDH STM-1If you select PDH setup, the PDH setup items which are applicable to setup will appear.And for SDH, the SDH setup items which are applicable to setup will appear.
Equipment Setup Equipment Setup (1/3)(1/3)SDH Equipment SetupSDH Equipment Setup
Equipment Setup (2/3)Equipment Setup (2/3) SDH Equipment SetupSDH Equipment Setup
Equipment Setup (2/3)Equipment Setup (2/3)PDH Equipment SetupPDH Equipment Setup
Equipment Setup (2/3)Equipment Setup (2/3) PDH Equipment SetupPDH Equipment Setup
For QPSKFor QPSK
For 16QAMFor 16QAM
For 32QAMFor 32QAM
Equipment Setup (3/3)Equipment Setup (3/3)ODU FREQ. INFOODU FREQ. INFO
Edit the point of TX frequency which should be within the range of the Start and Stop Sub-band indicated on the plate of the ODU.
The Rx frequency is automatically calculatedAccording to the Shift frequency.
For Twin path systems, two different RF Frequencies should entered.
ID1 to ID16 is available and ID17 to ID32 is Available for XPIC system.
InventoryInventory
InventoryInventory
• Select “Open” or “Close” to apply to the output mode to apply for event output.
• From INPU1 to INPUT6 can be assigned as housekeeping Alarm HK1 to HK6.
• From INPUT3 to INPUT6 can be assigned as Input Cluster Alarm Cluster IN1 toCluster IN4.
• From OUTPUT1 to OUTPUT4 can be assigned as HK3 to HK6.
• From OUTPUT1 to OUTPUT4 can be assigned as Cluster OUT1 to OUT4.
Cluster can be used as IN + OUT ≤ 4
• Click “SET” Command to execute.
MaintenanceMaintenance PDH Maintenance
A pop-up menu will appear To select which Ch. Will be looped
MaintenanceMaintenance SDH Maintenance
MaintenanceMaintenance
• Select ‘CTRL’ for IDU or ‘ODU’ for No.1 or No.2 and click the ‘execute button’.
• Check “With ROM “Program” Switching”Control box when the program file for “CTRL”Or “ODU” is newly downloaded and existing Program file will be replaced with the new one.• Reset the “CTRL” card will affect the radio link
MaintenanceMaintenance
MaintenanceMaintenance
Provisioning (1/4)Provisioning (1/4) PDH Provisioning
Provisioning (2/4)Provisioning (2/4)
ATPC MODE
MTPC MODE
PDH Provisioning
Provisioning (3/4)Provisioning (3/4)
ATPC MODE
MTPC MODE
AssignableFor RS-232C-1 or -2
AssignableFor V.11-1 or -2
SDH Provisioning
Provisioning (4/4)Provisioning (4/4)
MeteringMetering
Provisioning Provisioning
PMON (Current) for PMON (Current) for PDH EquipmentPDH Equipment
PMON (History)PMON (History)
PMON (History)PMON (History)
PMON (Current) for PMON (Current) for SDH EquipmentSDH Equipment
PMON (History)PMON (History)
PMON (History)PMON (History)
NESIC CAIRO NESIC CAIRO International Training CenterInternational Training Center