"RBLNational Accreditation Board for

Testing and Calibration Laboratories(An Autonomous Body under Department of Science & Technology, Govt. of India)

CERID'ICATE OFACCREDITATION

TCR ADVANCED ENGINEERING PRIVATE LIMITEDhas been assessed and accredited in accordance with the standard

ISO/lEe 17025:2005/IGeneral Requirements for the Competence of Testing & Calibration Laboratories"

for its facilities at250-252/9, GIDC, Makarpura, Naren Hardware Lane, Vadodara, Gujarat

inthe discipline ofMECHANICAL TESTING

(To see the scope of accreditation of this laboratory, you may also visit NABL website www.nabl-india.org)

Certificate Number T-1331

Valid Until 13/10/2017Issue Date 14/10/2015

This certificate remains valid for the Scope of Accreditation as specified in the annexure subject tocontinued satisfactory compliance to the above standard & the additional requirements of NABL.

Signed for and on behalf of NABL .

~Anil ReliaDirector

Prof. S. K. JoshiN. VenkateswaranProgram Manager Chairman

HflBLSCOPE OF ACCREDITATION

Laboratory TCR Advanced Engineering Private Limited, 250-25219, GIDC,Makarpura, Naren Hardware Lane, Vadodara, Gujarat

Accreditation Standard ISO/IEC 17025: 2005

Issue Date 14.10.2015

Valid Until 13.10.2017

Page 1 of 3

Test Method Specificationagainst which tests areperformed

Range of Testing ILimits of Detection

Discipline Mechanical Testing

Certificate Number T-1331

Last Amended on 26.10.2015

S.No. Product IMaterial of Test

Specific Test Performed

[. MECHANICAL PROPERTIES OF MATERIALS

1. Metallic Material Tensile TestUltimate Tensile strengthProof stressYield StressReduction in areasElongationLoad Test

Bend Test

Brinnel Hardness Test

Vickers Hardness Test

Rockwell Hardness Test

Micro Hardness Vickers

Charpy V notch impact Test(+)30 °C to (-)196 "C)

Gaurav SainiConvenor

ASTM A370-14,ASTM E8-15a,IS 1608: 2005,EN 10002: 2001,ASME (Sec IX): 15,EN 15614-1: 2008

0.5 kN to 600 kN

ASTM A 370-14,ASTM E 190-14,ASTM E 290-14,IS 1599: 2012,EN 5173: 2010,ASME (Sec IX): 15

ASTM E 10-15,IS 1500: 200.5

4,6,10,12,17,20,24,25,32,40,44,50,55,60mm mandrel dia

100 I-rBWto 400 HBW2.5/187.532 to 125 HBW 2.5/62.5100 to 400 HEW 10/3000100 to 400 HEW 5/750

IS 1501 (Part 1): 2013,ASTM E 384-11

40 to 800 HV5100 to 1000 HVIO100 to 1200 HV 3030 to 100 HRA30 to 100 HRB20 to 70 HRC40 to 1000 HVLoad 25 ,50, 100, 200,300,500,1000 gms2 J to 350 J

IS 1586: 2000,ASTM E 18-15

IS 1501 (Part I):2013,ASTM E 384-11

ASTM E23-12,ISO 148-2: 2008,EN 10045: 1990

N. VenkateswaranProgram Manager

rtflBLSCOPE OF ACCREDITATION

Laboratory TCR Advanced Engineering Private Limited, 250-25219, GIDC,Makarpura, Naren Hardware Lane, Vadodara, Gujarat

Accreditation Standard ISOllEe 17025: 2005

Discipline. Mechanical Testing Issue Date 14.10.2015

Certificate Number T-1331 Valid Until 13.10.2017

Last Amended on 26.10.2015 Page 2 of 3

S.No. Product I Specific Test Performed Test Method Specification Range of Testing IMaterial of Test against which tests are Limits of Detection

performed

2. Metallic Materials Micro Examination:General Structure ASTME 407-07, Grain Size: 1 to 14ASTMGrain size ASTME 3-11,

ASTME 1351:96ASTMA247: 10ASTM E 112- 13

Thickness of coating ASTMB 487 (RA2013) 0.01 rnmto 0.8 mm

Macro etchTest ASTME 340-15, QualitativeASTMA381 (RA 2005)EN ISO 17639:2013

De carburizationDepth ASTME1077-14, 0.01 mmto 0.8 mmIS 6396: 2000 (RA 2007).

Quantative Metallography ASTME-562-11 I %to 99%LOD= 1%

Linear Measurements TCRlADVrrM-37 Rev 03 dated 0.001 mm to 10mm05/10/2015

3. Reinforcement Bend Test of reinforcementbar . IS 1786:2008 4,6,10,12,17,20,24,BarrrMT Bar Rebend test of reinforcementbar 25,32,40,44,50,55,

ITMTbar 60 mmmandrel dia

4. Metallic material FlatteningTest ASTMNSA 370-14, OD(Tubes / Pipes.) ASTMB 11I-II 6 mm to 250 mm

5. Nuts Proof Load ASTMNSA 370: 14, 0.1 kN to 600 kNASTMNSA 194: 15,IS 1367(Part 6): 1994(RA 2004)

Gaurav SainiConvenor

N. VenkateswaranProgram Manager

HflBLSCOPE OF ACCREDITATION

Laboratory TCR Advanced Engineering Private Limited, 250-252/9, GIDC,Makarpura, Naren Hardware Lane, Vadodara, Gujarat

Accreditation Standard ISO/IEC 17025: 2005

Discipline Mechanical Testing Issue Date 14.10.2015

Certificate Number T-1331 Valid Until 13.10.2017

Last Amended on 26.10.2015 Page 3 of 3

S.No. Product I Specific Test Performed Test Method Specification Range of Testing IMaterial of Test against which tests are Limits of Detection

performed

6. StudlBolts FULL Size 8reaking! Tensile ASTM NSA 370-14, 0.1 kN to 600 kNtest/Proof load ASTM NSA 193-15,

IS 1367 (part 3): 2002,

7. Tube to Tube sheet Pull out test/push out test ASME (Sec VIll) Div-I: 2013 O. I kN to 600 kNMock up

8. Ferrous Material Nodularity in SOl iron IS 1754: 2002 Qualitative

9. Wrought Metallic Inclusion rating ASTM E45-13 QualitativeMaterials Method A

Method D

10. Stainless Steel IGCTEST ASTM A 262-14, QualitativePractice A DIN 3651-1 & 2: 1998

Practice 8 ASTM A 262-14, QualitativeDIN 3651-1 & 2: 1998

Practice C ASTM A 262-14, QualitativeDIN 3651-1 &2: 1998

Practice E ASTM A 262-14, QualitativeDIN 3651 -1 & 2: 1998

Pitting corrosion method A ASTMG48-11 QualitativeCrevice corrosion method 8

Inter metallic phase in Duplex ASTM A 923-14 o to 350 Jaustenitic/ferritic stainless steel ASTM A 923Method A ASTM A 923Method 8Method C

11. Metallic & Non Salt Spray Testing ASTM 8-117-11 QualitativeMetallic Materials IS 9844:1981 (Ra 2006)

ISO 9227:2012

-x-x-x-x-x-x-x-x-x-x-x-x-x-x-

N. VenkateswaranProgram Manager

Gaurav SainiConvenor