MUSW-001_CE_certificate---781cc931-eb36-41e2-b61e-37ca42222803.pdf

ETSI EN 300 328 V1.7.1: 2006-10 TEST REPORT

For

2.4GHz Wireless Mouse

Report No.: AGC10201009SZ03E2

Prepared For

Prepared By

Attestation of Global Compliance Co., Ltd.

2F., No.2 Building, Huafeng No.1 Technical Industrial Park, Sanwei,

Xixiang, Baoan District, Shenzhen

TEL: 86-755-2908 1966

FAX: 86-755-2600 8484

Brand Name:

Date of Issue: Nov. 15, 2013

Gembird Europe B.V.

Wittevrouwen 56, 1358CD Almere, The Netherlands.

Model Name:MUSW-001

GEMBIRD

Phone: +31-36-5211588

ANNA

Report No.: AGC10201009SZ03E2 Page 1 of 32

TABALE OF CONTENTS

1. TEST RESULT CERTIFICATION 2

2. TECHNICAL INFORMATION 3

2.1 EUT DESCRIPTION 3

2.2 OBJECTIVE 4

2.3 TEST STANDARDS AND RESULTS 4

3. DETAILS OF TEST 5

3.1 IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION 5

3.2 LIST OF TEST EQUIPMENTS 5

3.3 ENVIRONMENTAL CONDITIONS 5

3.4 MEASUREMENT UNCERTAINTY 5

4. ETSI EN 300 328 REQUIREMENTS 6

4.1 MAXIMUM TRANSMIT POWER 6

4.2 FREQUENCY RANGE 8

4.3 FREQUENCY HOPPING REQUIREMENTS 10

4.4 MEDIUM ACCESS PROTOCOL 11

4.5 TRANSMITTER SPURIOUS EMISSIONS 12

4.6 RECEIVER SPURIOUS EMISSIONS 21

APPENDIX I 27

PHOTOGRAPHS OF THE TEST SETUP 27

APPENDIX II 28

PHOTOGRAPHS OF THE EUT 28


1. TEST RESULT CERTIFICATION

Applicant Name:

Address:

Manufacturer Name:

Address:

Brand Name: GEMBIRD

Equipment Under Test: 2.4GHz Wireless Mouse

Model Number: MUSW-001

Test Standard ETSI EN 300 328 V1.7.1 (2006-10)

File Number: AGC10201009SZ03E2

Date of Test: Nov. 15, 2013

We (AGC), Attestation of Global Compliance Co., Ltd. for compliance with the requirements set forth in the European Standard ETSI EN 300 328 V1.7.1. The results of testing in this report apply to the product/system which was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties.

Checked By:

Tony Tian Nov. 15, 2013

Authorized By: King Zhang Nov. 15, 2013

Gembird Europe B.V.

Gembird Electronics Ltd.


5/F, Building B, Shifeng Industry District, Huaning Road, Dalang St., Longhua, Bao'an, Shenzhen, Guangdong, China

ANNA


2. TECHNICAL INFORMATION Note: the following data is based on the information by the applicant. 2.1 EUT DESCRIPTION

esuoM sseleriW zHG4.2 tcudorP

Applicant Company

Applicant Address

Manufacturer Company

Manufacturer Address

Brand Name GEMBIRD

Model Number MUSW-001

Power Supply Internal Lion Composite Battery Normal Voltage:3V Extreme Voltage :2.7V-3.3V

Note: 1. The EUT provides wireless interface operating at 2.4GHz ISM band (2402MHZ-2480MHZ). The EUT use

Frequency Hopping Spread Spectrum (FHSS) modulation.

2. Please refer to Appendix for the photographs of the EUT. For more details, please refer to the Users manual of the EUT.


5/F, Building B, Shifeng Industry District, Huaning Road, Dalang St.,Longhua, Bao'an, Shenzhen, Guangdong, China

Gembird Europe B.V.

Gembird Electronics Ltd.


2.2 OBJECTIVE Perform Radio Spectrum tests for CE Marking according to the provisions of article 3.2 of the R&TTE Directive (1999/5/EC) for the Bluetooth function of the EUT. 2.3 TEST STANDARDS AND RESULTS The EUT has been tested according to ETSI EN 300 328 V1.7.1 (2006-10).

ETSI EN 300 328 V1.7.1 (2006-10)

Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2.4GHzHz ISM band and using spread spectrum modulation techniques: Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive.

Test items and the results are as bellow:

Basic Standard Test Type Result

1 ETSI EN 300 328 4.3.1 Maximum Transmit Power Pass

2 ETSI EN 300 328 4.3.2 Maximum EIRP Spectral Density N/A

3 ETSI EN 300 328 4.3.3 Frequency range Pass

4 ETSI EN 300 328 4.3.4 Frequency Hopping Requirements Pass

5 ETSI EN 300 328 4.3.5 Medium Access protocol Implemented

6 ETSI EN 300 328 4.3.6 Transmitter spurious emission Pass

7 ETSI EN 300 328 4.3.7 Receiver spurious emission Pass


3. DETAILS OF TEST 3.1 IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION

Company Name: Site 1: Word Standardization Certification & Testing Co., Ltd. Site 2: Shenzhen Attestation of Global Compliance Science & Technology Co., Ltd

Address:

1-2/F, Dachong Keji Building, No.28 of Tonggu Road, Nanshan District, Shenzhen, 518057, China 2F, No.2 Building, ChaXi SanWei Industrial Zone, GuShu Community, XiXiang Street, BaoAn, ShenZhen, China

3.2 LIST OF TEST EQUIPMENTS

Description Manufacturer Model No. Calibration Date Calibration Due.

Test Receiver ROHDE&SCHWARZ ESCS30 Apr.14, 2009 Apr.13, 2010

Wideband Ant Sunol Sciences Corp. JB3 Apr.14, 2009 Apr.13, 2010

H&T Chamber EXPERY TN-400 Apr.14, 2009 Apr.13, 2010

ANTENNA R&S VULB9163 Apr.14, 2009 Apr.13, 2010

Regulated DC Power Supply LONGWEI 50V30A Apr.14, 2009 Apr.13, 2010

Universal Radio Communication Tester R&S CMU200 Sep.23, 2008 Sep.22, 2009

Horn Antenna ETS 3117 Apr.14, 2009 Apr.13, 2010

SPECTRUM ANALYZER AGILENT E4443A Sep.23, 2008 Sep.22, 2009

3.3 ENVIRONMENTAL CONDITIONS

During the measurement the environmental conditions were within the listed ranges: - Temperature: 15-35C - Humidity: 30-60 % - Atmospheric pressure: 86-106 kPa 3.4 MEASUREMENT UNCERTAINTY

The uncertainty is calculated using the methods suggested in the Guide to the Expression of Uncertainty in Measurement (GUM) published by ISO.

- Uncertainty of Conducted Emission, Uc = 1.8dB - Uncertainty of Radiated Emission, Uc = 3.2dB


4. ETSI EN 300 328 REQUIREMENTS 4.1 MAXIMUM TRANSMIT POWER EN 300 328 Clause 4.3.1 Radiated Power


TEST PROCEDURE 1. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.3 for the test conditions. 2. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.7.2.2 for the measurement method.

TEST RESULTS

Operation Mode: TX Test Date: Sept.22, 2010

Temperature: 25oC Tested by: Jekey

Humidity: 55 % RH Polarity: --

Duty Cycle Measurement X (Ton/ (Ton+Toff)) = 0.3

Antenna assembly Gain = 2.0 dB

Cable Loss (used for conducted testing) =1.5 dB

EIRP = AVG+ Gain+10log (1/x)

TEST CONDITIONS TRANSMITTER POWER (dBm)

Temp (25)C Temp (-20)C Temp (55)C

CHANNEL VOL POWER 3.0V 2.7V 3.3V 2.7V 3.3V

2410MHz AVG -15.53 -15.65 -15.30 -15.33 -15.34

EIRP -8.30 -8.42 -8.07 -8.10 -8.11

2437MHz AVG -15.34 -15.27 -15.56 -15.34 -15.58

EIRP -8.11 -8.04 -8.23 -8.11 -8.35

2465MHz AVG -15.36 -15.34 -15.58 -15.33 -15.50

EIRP -8.13 -8.11 -8.35 -8.10 -8.27

Limit 20dBm

Measurement uncertainty + 0.28dB / - 0.30dB

Note: AVG Value including Cable loss used for conducted testing Conclusion: PASS


4.2 FREQUENCY RANGE ETSI EN 300 328 clause 4.3.3.2 For all equipment the frequency shall lie within the band 2.4GHzHz to 2.4835GHz (fL >2.4GHzHz and fH< 2.4835GHz)

TEST CONFIGURATION Temperature and Voltage Measurement (under normal and extreme test conditions)

Remarks: The spectrum analyzer could be connected to a monopole antenna or directly connected to the EUT, if the EUT has already employing an antenna connector.

TEST PROCEDURE 1. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.3 for the test conditions. 2. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.7.4 for the measurement method.

Monopole Antenna

Spectrum analyzer

Variable AC Power Supply

Temperature Chamber

EUT

(See Note)


TEST RESULTS

2102 ,22.tpeS :etaD tseT XT :edoM noitarepO

Temperature: 25o yekeJ :yb detseT C

Humidity: 55 % RH Polarity: --

TEST CONDITION Frequency Range

Low Frequency High Frequency zHM zHM egatloV erutarepmeT

25C Vnor 3.0 2409.53 2465.52

-20C Vmin 2.7 2409.56 2465.54 Vmax 3.3 2409.68 2465.58

55C Vmin 2.7 2409.55 2465.55 Vmax 3.3 2409.57 2465.57

Measured frequencies (lowest and Highest) 2409.53 2465.58

zHM5.3842 < HF zHM0042 > LF timiL

Conclusion: PASS


4.3 FREQUENCY HOPPING REQUIREMENTS ETSI EN 300 328 SUBCLAUSE 4.3.4.1 DEWELL TIME The Maximum Dwell Time shall be 0.4S ETSI EN 300 328 SUBCLAUSE 4.3.4.2 HOPPING CHANNEL The hopping Channels defined within a hopping sequence shall be at least 1 MHz aprt (Channel Separation) ETSI EN 300 328 SUBCLAUSE 4.3.4.3 HOPPING SEQUENCE Each hopping channel of the hopping sequence shall be occupied at least once during a period not exceeding four times the product of the dwell time per hop and the number of channels. TEST CONFIGURATION TEST PROCEDURE 1. Connect EUT antenna terminal to the spectrum analyzer with a low loss cable.

Dwell Time: Equipment mode: Spectrum analyzer RBW: 1MHz VBW: 1MHz SPAN: Zero Span Channel Separation: Equipment mode: Spectrum analyzer RBW: 100KHz VBW: 100KHz SPAN: 5MHz Hopping Sequence: Equipment mode: Spectrum analyzer RBW: 1MHz VBW: 1MHz SPAN: Zero Span

2. Adjust the center frequency of spectrum analyzer on any frequency be measured. 3. Measure the Dwell Time, Channel Separation, Hopping Sequence by spectrum analyzer Marker function. 4. Repeat above procedures until all frequencies measured were complete. TEST RESULT This device accords with standards requirements.

Monopole Antenna

Spectrum analyzer

EUT

(See Note)


4.4 MEDIUM ACCESS PROTOCOL ETSI EN 300 328 SUBCLAUSE 4.3.5 A medium access protocol shall be implemented by the equipment Conclusion: This device implemented medium access protocol


4.5 TRANSMITTER SPURIOUS EMISSIONS Spurious emissions are emissions outside the frequency range(s) of the equipment as defined in Clause 5.2.3.

The level of spurious emissions shall be measured as, either:

1. Their power in specified load (conducted spurious emissions); and

2. Their effective radiated power when radiated by the cabinet or structure of the equipment (cabinet radiation); or

3. Their effective radiated power when radiated by cabinet and antenna.

The spurious emissions of the transmitter shall not exceed the values in tables in the indicated bands:

Transmitter limits for NARROWBAND spurious emissions

Frequency Range Limit when operating Limit when in stand-by

30 MHz to 1 GHz -36 dBm -57 dBm

Above 1 GHz to 12.75 GHz -30 dBm -47 dBm

1.8 GHz to 1.9GHz

5.15 GHz to 5.3GHz -47 dBm -47 dBm

Transmitter limits for WIDEBAND spurious emissions

Frequency Range Limit when operating Limit when in stand-by

30 MHz to 1 GHz -86 dBm -107 dBm

Above 1 GHz to 12.75 GHz -80 dBm -97 dBm

1.8 GHz to 1.9GHz

5.15 GHz to 5.3GHz -97 dBm -97 dBm


Test Configuration

Below 1GHz

Spectrum analyzer

10m

4m

1mTurntable

EUT

1.5m

Antenna tower

Reference ground plane

Bi-log or Loop antenna

Above 1GHz

Spectrumanalyzer

Horn antenna

10m

4m

1m Turntable

EUT

1.5m

Antenna tower

Pre-amp

TEST PROCEDURE 1. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.3 for the test conditions. 2. Please refer to ETSI EN 300 328 (V1.7.1) clause 5.7.5 for the measurement methods.


TEST RESULTS for 638RG(Radiated Method)

Transmitter Operating Mode TRANSMITTER SPURIOUS EMISSION BELOW 1GHZ HORIZONTAL

TRANSMITTER SPURIOUS EMISSION BELOW 1GHZ VERTICAL


RESULTS:

Freq. Antenna Reading Total Factor Corrected Power Limit(MHz) Polarity (dBm) (dB) (dBm) (dBm)

30.000 H -60.61 19.92 -40.69 -36266.000 H -80.48 18.58 -61.90 -3631.600 V -61.50 19.91 -41.59 -36

288.700 V -81.30 20.11 -61.09 -36


TRANSMITTER SPURIOUS EMISSION ABOVE 1GHZ HORIZONTAL

TRANSMITTER SPURIOUS EMISSION BELOW 1GHZ VERTICAL


RESULTS Freq. Antenna Reading Total Factor Corrected Power Limit(MHz) Polarity (dBm) (dB) (dBm) (dBm)

2450.000 H -30.39 22.17 -8.22 -3310.000 H -65.28 20.15 -45.13 -302450.000 V -29.41 21.17 -8.24 --3310.000 V -64.43 20.15 -44.28 -30

Transmitter Standby Mode:

TEST DATA IS MUCH LOWER THAN LIMITS.


TEST RESULTS for 638RG (Conducted Method)

Transmitter Operating Mode


Transmitter Standby Mode for 638RG

TEST DATA IS MUCH LOWER THAN LIMITS.

Conclusion: PASS


4.6 RECEIVER SPURIOUS EMISSIONS The level of spurious emissions shall be measured as, either:

1. Their power in specified load (conducted spurious emissions); and

2. Their effective radiated power when radiated by the cabinet or structure of the equipment (cabinet radiation); or

3. Their effective radiated power when radiated by cabinet and antenna.

The spurious emissions of the receiver shall not exceed the values in tables in the indicated bands:

Receiver limits for NARROWBAND spurious emissions

Frequency Range Limit when in stand-by

30 MHz to 1 GHz -57 dBm

Above 1 GHz to 12.75 GHz -47 dBm

Receiver limits for WIDEBAND spurious emissions

Frequency Range Limit when in stand-by

30 MHz to 1 GHz -107 dBm

Above 1 GHz to 12.75 GHz -97 dBm

MEASUREMENT EQUIPMENT USED

Same as section 4.4 in this test report

Test Configuration

Radiated Spurious Emissions:

Same as section 4.4 in this test report

TEST PROCEDURE 1. Please refer to ETSI EN 300 328 (V1.4.1) clause 5.3 for the test conditions. 2. Please refer to ETSI EN 300 328 (V1.4.1) clause 5.7.6 for the measurement methods.


TEST RESULTS for 638RG (Radiated Method)

Receiver Mode

RECEIVER SPURIOUS EMISSION BELOW 1GHZ HORIZONTAL

RECEIVER SPURIOUS EMISSION BELOW 1GHZ VERTICAL


RESULTS

Freq. Antenna Reading Total Factor Corrected Power Limit(MHz) Polarity (dBm) (dB) (dBm) (dBm)

183.600 H -83.01 22.01 -61.00 -57571.600 H -83.61 19.07 -64.54 -57290.300 V -82.82 15.17 -67.65 -57621.700 V -82.440 18.15 -64.29 -57


RECEIVER SPURIOUS EMISSION ABOVE 1GHZ HORIZONTAL

RECEIVER SPURIOUS EMISSION ABOVE 1GHZ VERTICAL


RESULTS

Freq. Antenna Reading Total Factor CorrectedPower Limit(MHz) Polarity (dBm) (dB) (dBm) (dBm)2840 H -70.41 15.09 -55.32 -476400 H -70.30 16.08 -54.22 -478950 H -70.28 17.86 -52.42 -473190 V -70.08 15.45 -54.50 -476780 V -70.12 16.78 -53.34 -479540 V 70.68 17.53 -53.15 -47


TEST RESULTS for 638RG(Conducted Method)

Receiver Mode

Conclusion: PASS


APPENDIX I

PHOTOGRAPHS OF THE TEST SETUP

RADIATED SPURIOUS EMISSION TEST BELOW 1GHZ

RADIATED SPURIOUS EMISSION TEST ABOVE 1GHZ


APPENDIX II PHOTOGRAPHS OF THE EUT

ALL VIEW OF SAMPLE

TOP VIEW OF SAMPLE


BOTTOM VIEW OF SAMPLE

LEFT VIEW OF SAMPLE


RIGHT VIEW OF SAMPLE

FRONT VIEW OF SAMPLE


BACK VEIW OF SAMPLE


INTERNAL PHOTO OF SAMPLE 1

INTERNAL PHOTO OF SAMPLE 2

----END OF REPORT----

Documents

MUSW-001_CE_certificate---781cc931-eb36-41e2-b61e-37ca42222803.pdf