MULTIFORM MASTER TABLE · 2014. 2. 10. · MULTIFORM MASTER TABLE v13-01 The EZ SMART Multiform Master Table is a lightweight, portable, and adjustable multipurpose work table. The

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470Phone (352) 620-2262 Fax (352) 620-2576 Tech (732) 259-9984 [email protected] www.eurekazone.com

MULTIFORM MASTER TABLE

v13-01

The EZ SMART Multiform Master Table is a lightweight, portable, and adjustable multipurpose work table. The sliding supports, with user-supplied sacrificial wood, can expand to support a full 4' x 8' sheet of plywood. As a material support table, it is used in conjunction with the EZ SMART Tracksaw System, EZ SMART Universal Edge Guide, and the EZ SMART Super Routing Kit. The open top and open slots in the extrusions allow for a variety of other uses and modifications. The side rail extrusions can also be substituted with other EZ SMART extrusions to increase its versatility.

PARTS:(4) Leg Assemblies (2 left and 2 right)(4) Bracket Feet with connectors(2) Upper End Rail with connectors(2) Lower End Braces with connectors(2) 48” Side Rails(4) Sliding Fences with connectors(4) 24” Sliding Plastic Extrusions(4) 8” Sliding Plastic Extrusions(1) Bag of screws to attach wood to

Sliding Plastic Extrusions

mailto:[email protected]://www.eurekazone.com/

Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470Phone (352) 620-2262 Fax (352) 620-2576 Tech (732) 259-9984 [email protected] www.eurekazone.com v13-03

ASSEMBLING THE TABLE

STEP 1: Remove the feet from the Leg Assemblies. Set aside.STEP 2: Remove the connectors from the Upper End Rails. Set aside.STEP 3: Loosen screws for the T-slot bar on Leg Assembly. Slide Upper End Rail onto the T-slot bar until aligned with corner. Tighten the screws. Repeat for the other Leg Assemblies.

T-Slot Bar

STEP 4: Slide the connectors that were removed from the Upper End Rail (Step 2) into the legs and align with hole in the end of the Upper End Rail. Attach with screw. Repeat for other Leg Assemblies. The end result will be two End Assemblies.

STEP 5: Loosen screws on the Lower End Brace but do not remove screw or connector. Slide the Lower End Brace into each Leg of the End Assembly. Place about 10”-12” from bottom of the Leg. Tighten the screws.



STEP 6: Insert Bracket Feet into outer slot of the Legs. Tighten the screws.

STEP 7: Loosen cap screws on underside of the Leg Assembly corner. Slide end of 48” Side Rail over the corner until flush with the end. Tighten the screws and repeat for the other Side Rail.

STEP 8: Loosen connectors on the Sliding Fences. Insert Fences in to the Side Rails. Locate where desired and tighten the screws.

Screw Access



STEP 9: Insert 24” Sliding Plastic Extrusions into the Sliding Fences. Insert 8” Sliding Plastic Extrusions into the Side Rails.STEP 10: Attach user-supplied 1X lumber to the Sliding Plastic Extrusions using the provided self-tapping screws. Using 4-5 screws per Fence should be sufficient. Notes: The 1X lumber can be cut to any length though 24” is a common length. Due to the difference in location of the short Sliding Plastic Extrusions compared to those on the Sliding Fences, the lumber used for these should be wider.

Completed Multiform Master TableWith Wood Supports

24” 1x4* 24” 1x3*

* user-supplied lumber

Attach screws through sides of plastic extrusions


Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470Phone (352) 620-2262 Fax (352) 620-2576 Tech (732) 259-9984 [email protected] www.eurekazone.com

USING THE MASTER TABLE

Supporting a full sheet of plywood

Using the Universal Edge Guide* Using the EZ SMART Super Routing Kit* and EZ SMART Tracksaw System*

* Sold separately

Using the EZ SMART Tracksaw System*

Plywood Top Workbench / Tool Stand Adjustable Legs for Smaller Footprint


Slide 1Slide 2Slide 3Slide 4Slide 5

Documents

MULTIFORM MASTER TABLE · 2014. 2. 10. · MULTIFORM MASTER TABLE v13-01 The EZ SMART Multiform Master Table is a lightweight, portable, and adjustable multipurpose work table. The