Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
www.checkersindustrial.com
Dedicated to saving lives and protecting assets.
ECONOMAT MB™
MULITPURPOSE BOARD FOR BUILDERSAND EVENT ORGANIZERS
MECHANICAL PROPERTIES UNIT LDPE
Tensile Strength MPa 5-25
Flexural Strength MPa 25-28
Flexural Modulus MPa 250
Charpy Notched Impact Strength kJ/m2 5-6
Poisson’s Ratio (theoretical) 0.35-0.38
GENERAL PROPERTIES UNIT LDPE
Density kJ/m3 <940
Water Absorption % 0.015
Thermal Expansion x10-6 K-1 100-200
Thermal Conductivity W/m.K 0.33
Specific Heat J/kg.K 1900-2300
Melting Temperature ˚F 248
Service Temperature ˚F -22 - +185
ECONOMAT MB™ LIGHTWEIGHT MULTIBOARD
COST EFFECTIVE ALTERNATIVE TO PLYWOOD• Economat MB™ has been specifically developed
as an effective and efficient alternative to construction plywood providing a low cost, easy to deploy and reusable temporary access and ground protection solution.
• With the risk of slippage or falls and injury from splinters, together with the short lifespan, increasing costs and its environmental disposal, makes plywood less safe and more expensive than Economat MB™
REUSABLE LONG TERM ADVANTAGES• As with plywood, Checkers® Economat MB™ can be used as a tough multi-use
construction board; mixing of cement, storing soil, creating construction site walkways or protective up stands – jobs where plywood would typically be used.
• Economat MB™ delivers enhanced performance, and health and safety benefits compared to construction plywood.
• Economat MB™ is resistant to adverse weather making it ideal for use in snow, ice, frost or damp conditions. Made from 100% recycled Low Density Polyethylene, Economat MB™ can be reused time and again providing considerable long term cost savings over plywood.
FAST EFFICIENT INSTALLATION• At just 70.5 lb., Economat MB™ is easy to handle and simple to deploy. With a
range of connection options, Economat MB™ can be joined to form access ways, walkways, work pads and storage depot areas with the option of an anti-slip traction surface or smooth surface.
• Economat MB™ is also ideal for event flooring.
ADVANTAGES:
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
*Compression tested at National Physical Laboratory, UK
• Fast and easy to install• Traction surface for safe vehicle and pedestrian use• Made from 100% recycled Low Density Polyethylene • Reusable multi-use board • Safer, more cost effective and lightweight
alternative to construction plywood• Connection options for different ground
conditions and equipment• Resistant to degradation caused by weather
conditions
FEATURES:
ECONOMAT MB™ CONNECTION SYSTEMS
APPLICATIONS:• Multi-Use Construction
Board• Events and Pedestrian
Walkways• Temporary Roadways• Spoil and Waste Storage
• Dry Storage for Building Materials
• Bulk Aggregate Storage• Protective Upstands• Protection of Ground or
Surface Against Spillages
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
From the Experts in Industrial Safety
STANDARD 2 WAY / 4 WAY URETHANE CONNECTORS• Made from 100% Urethane, 2 and 4 way connectors are inserted
from below and attached via M10 bolts. • Connectors can be strengthened with a metal strap for projects
where heavy vehicles or equipment are used, or on inclines or slopes.
FAST FIT CONNECTORS• Used on short term projects where speed of installation is of the
essence. The connector is simply pushed through the holes and then underneath the mats.
FLEX CONNECTORS• Installed in the same way as 2 or 4 way connectors the ‘flex’ connectors
should be used where there is highly undulating ground.
METAL U-PIN• Metal U-pin connectors should be used in conjunction with other
connectors when Economat MB are installed on inclines or slopes.
ECONOMAT MBTM MULTIBOARD TEMPORARY ACCESS AND GROUND PROTECTION MAT • Material: 100% Recycled Low Density Polyethylene• Size: 94.88” x 47.24” x .43”• Weight: 70.5 lb.
TECHNICAL PRODUCT INFORMATION: For use as a technical guide only
MECHANICAL PROPERTIES UNIT LDPE
Tensile Strength MPa 5-25
Flexural Strength MPa 25-28
Flexural Modulus MPa 250
Charpy Notched Impact Strength kJ/m2 5-6
Poisson’s Ratio (theoretical) 0.35-0.38
GENERAL PROPERTIES UNIT LDPE
Density kJ/m3 <940
Water Absorption % 0.015
Thermal Expansion x10-6 K-1 100-200
Thermal Conductivity W/m.K 0.33
Specific Heat J/kg.K 1900-2300
Melting Temperature ˚F 248
Service Temperature ˚F -22 - +185
To view our full line of Safety Products, visit us at www.checkersindustrial.com or call 1-800-438-9336.
Dedicated to saving lives and protecting assets
Dedicated to saving lives and protecting assets.
*Load performance depends on ground conditions as well as the weight and type of vehicles and plant. Checkers®, its agents or employees are not liable for any damage to existing ground or property through use of Economat MB™.
The sale or hire of all temporary access mats are subject to Checkers®’ standard Terms and Conditions. These are available from our website checkersindustrial.com or by telephoning our sales office.
HEALTH AND SAFETY INFORMATION:
GENERAL UNIT
Critical Hazards to Man and Environment None
Environment The disposal of the material presents no danger regarding toxicological or ecological considerations. Due to low water solubility, bio-availability unlikely.
Solubility in Water Insoluble
Regulatory Not classified as hazardous under transport regulations.
SAFETY PROPERTIES UNIT
Melting Point Crystalline Melt Temperature 275 - 293˚F
Ignition Temperature > 680˚F
Thermal Decomposition > 734˚F
Stability and Reactivity No possibility of degradation under normal circumstances.Degradation will only occur above the decomposition temperature.
Toxicology Not harmful to health under normal conditions.
www.checkersindustrial.com
Dedicated to saving lives and protecting assets.
GEOGRID®
CELLULAR PAVING SYSTEM
GEOGRID® CELLULAR PAVING SYSTEM
GROUND REINFORCEMENT AND STABILIZATION• GeoGrid® cellular paving system enables the fast and efficient implementation of
ground reinforcement and stabilization. The cellular design of the grids allow the dispersion of excess rain or flood water which makes it ideal for integration with Sustainable Urban Drainage Systems (SUDS), areas prone to flooding, or water dispersion problems.
UNIQUE PATENTED DESIGN• GeoGrid®’s unique patented design offers the combination of excellent cellular
strength and weight load capability, allowing for optimal expansion and contraction by avoiding the risk of surface deformation in hot or cold climates.
FAST AND EFFICIENT INSTALLATION• Manufactured in Europe and made from 100% recycled polyethylene, GeoGrid®
features an effective and simple interlocking design for fast and efficient installation. The grids can be lifted directly from the pallet as pre-connected 1m2 sections and can be easily cut to form shapes around obstacles such as planters or posts, saving time and money on large scale installations.
ADVANTAGES:
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
*Compression tested at National Physical Laboratory, UK
• Ground reinforcement and stabilization • Ideal for integration into Sustainable Urban
Drainage Systems (SUDS)• Unique patented design avoids surface
deformation in high temperatures• Designed and manufactured in the UK
from 100% recycled polyethylene.• Fast and simple to install with simple
interlocking design• Durable and lightweight• Available in either Premium or Standard options• Capable of withstanding loads
up to 500 tons* / m2
FEATURES:
FAST AND SIMPLE TO INSTALL
GEOGRID® CELLULAR PAVING SYSTEM OPTIONS
APPLICATIONS:• Pathways and Driveways• New & Overflow Parking Lot• Ground Reinforcement
and Stabilization Including Slopes, Embankments and Storage Areas
• Integration into Sustainable Urban Drainage Systems (SUDS)
• Pedestrian Access Ways• Access Roads and
Roadways
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
From the Experts in Industrial Safety
GEOGRID® STANDARD• Due to its unique patented design, GeoGrid® Standard is capable
of withstanding weight loads up to 400 tons / m2 and a point load weight of 25 tons.
• Lightweight and easy to install, with the option of white or hi-viz demarcation blocks, GeoGrid® Standard is ideal for areas where the passage of pedestrians or light vehicles is required.
GEOGRID® PREMIUM• Withstanding weight loads up to 500 tons / m2 and a point load of
35 tons, GeoGrid® Premium offers the same patented design features as GeoGrid® Standard but provides enhanced performance capabilities.
• Still lightweight at 3.5 lb. per mat or 14.1 lb. per m2. GeoGrid® Premium utilizes the same simple interlocking design offering ease and speed of installation. With the enhanced weight baring capability, GeoGrid® Premium is ideal for areas where regular vehicle or heavy traffic is expected.
• Both systems can be infilled with either aggregate or decorative stones to provide robust ground reinforcement. Alternatively, GeoGrid® can be seeded with grass to provide an environmentally friendly and aesthetic option. The use of demarcation blocks enables GeoGrid® to be used in areas where there is a requirement for indicating specific zones, such as disabled parking bays and traffic flow directions.
• Event Parking• Road Extensions and
Widening• Equestrian and Outdoor
Events• Fire and Emergency Routes
• Infiltration Basins• Depot Storage Areas• Gateway Areas• Golf Cart Routes• Helicopter Landing Pads
GEOGRID® CELLULAR PAVING SYSTEM• Material: 100% Recycled High Density
Polyethylene (HDPE)• Size: 19.48” x 19.48” x 1.57”• Weight per grid: Standard - 2.42 lb.
Premium - 3.52 lb.• Weight per m2: Standard - 9.7 lb.
Premium - 14 lb.
TECHNICAL PRODUCT INFORMATION: For use as a technical guide only
To view our full line of Safety Products, visit us at www.checkersindustrial.com or call 1-800-438-9336.
Dedicated to saving lives and protecting assets
Dedicated to saving lives and protecting assets.
*Load performance depends on ground conditions as well as the weight and type of vehicles and plant. Checkers®, its agents or employees are not liable for any damage to existing ground or property through use of GeoGrid®.
The sale or hire of all temporary access mats are subject to Checkers®’ standard Terms and Conditions. These are available from our website checkersindustrial.com or by telephoning our sales office.
HEALTH AND SAFETY INFORMATION:
Weight loading / m2 Standard - 400 tons* • Premium - 500 tons*
Axel or Point Load Standard - 25 tons* • Premium - 35 tons*
Connectivity Simple Interlocking Design
Environmental Features Weather Proof and Water Resistant. Polyethylene is Resistant to Acids, Alkalies and Solvents.
Packaging Pre-Connected 1m2 Sections - 4 Grids60 Layers of 4 Grids Per Pallet • 240 Grids Per Pallet
Pallet Size and AreaRequired Per Pallet
105cm X 105cm X 120cm / 220cm (60m2)26 Pallets Per Standard Articulated Lorry
LogisticsTypically 1560m2 Of Geogrid® Per Standard EU Curtain Sided Trailer - Based Upon 26
Pallets of 60m2 Per Pallet. Pallets Can Be Loaded to Customer Requirements Up to Maximum of 60 Layers
Customization Optional White or High-Viz Demarcation Blocks Can Be Fitted into Grid Cells Indicating Specific Zones Such as Disabled Parking Bays and Traffic Flow Directions
Testing* Tested by National Physical Laboratory UH Under BSEN124: 1994
UK Patent No. 0808580.5
Installation Please Refer to Installation Guide and/or Seek Advice from QualifiedStructural or Civil Engineer.
GENERAL
Critical Hazards to Man and Environment None
Environment The disposal of the material presents no danger regarding toxicological or ecological considerations. This material is not expected to be readily biodegradable.
Solubility in Water Insoluble
Regulatory Not classified as hazardous under transport regulations.
SAFETY PROPERTIES
Melting Point Melt Temperature 194 - 284˚F
Ignition Temperature 626˚F - 770˚F
Thermal Decomposition > 572˚F
Stability and Reactivity No possibility of degradation under normal circumstances.
Toxicology Not harmful to health under normal conditions.
www.checkersindustrial.com
Dedicated to saving lives and protecting assets.
LIBERTYMAT™HEAVY DUTY TEMPORARY
ACCESS MAT
•
LIBERTYMAT™ HEAVY DUTY TEMPORARY ACCESS MAT
HEAVY DUTY TEMPORARY ACCESS MATS• Supporting loads up to 80 ton, LibertyMat™
is the ultimate heavy duty man-handleable mat for temporary roadways and work areas. LibertyMat™ is essential for the construction, civil engineering and ground work industries.
REUSABLE LONG TERM ADVANTAGES• Made from tough 100% recycled or virgin high density Polyethylene (HDPE),
LibertyMat™ is the market leader for temporary access and ground protection over soft or sensitive ground.
• LibertyMat™ significantly reduces damage to heritage and eco-sensitive areas, avoiding the need for reinstatement once the project is complete.
FAST & EFFICIENT INSTALLATION• Weighing just 77 lb. LibertyMat™ is ideal for both short and long term projects.
Incorporating strategically positioned handholds, LibertyMat™ is man-handleable and easy to off load and deploy by a two man team.
CHEVRON TRACTION® SURFACE• LibertyMat™’s chevron traction® surface comprises of a broken pattern of rugged
nubs which substantially improves the grip and forward motion of plant or vehicles and reduces sideway slippage, even in the most challenging weather or ground conditions.
• Optional hi-viz markings and cat eyes can be incorporated into LibertyMat™ for additional safety at night.
LOGISTICS• Lighter in weight than conventional wood or steel alternatives, LibertyMat™ also offers
the environmental benefit of more mats being loaded per wagon and in turn reducing transportation costs and carbon emissions.
ADVANTAGES:
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
*Compression tested at National Physical Laboratory, UK
• Fast and Easy to Install• Unique Chevron Traction® Surface• Reversible Low Profile Surface (Optional)• Low Transportation and Handling Costs• Minimizes Property and Environmental Damage• Supports Health and Safety Objectives• Connection Options for Different Ground
Conditions and Equipment• Non-Slip Reflective Markings and Cats
Eyes for Night Safety (Optional)
FEATURES:
LIBERTYMAT™ CONNECTION SYSTEMS
APPLICATIONS:• Construction, Civil Engineering
and Ground Work• Pedestrian Walkways• Emergency Access Routes • Temporary Roadways and
Parking Lots
• Utilities and Infrastructure Maintenance
• Landscaping and Protection of Heritage or Eco-Sensitive Areas
• Golf Course and Sports Field Maintenance
• Sports and Leisure Events
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
From the Experts in Industrial Safety
STANDARD 2-WAY / 4-WAY URETHANE CONNECTORS• Made from 100% Urethane, 2- and 4-way connectors are inserted
from below and attached via M10 bolts. Connectors can be strengthened with a metal strap for projects where heavy vehicles or equipment are used, or on inclines and slopes
FAST FIT CONNECTORS• Used on short term projects where speed of installation is of the
essence. The connector is simply pushed through the holes and then underneath the mats.
FLEX CONNECTORS• Installed in the same way as 2- or 4-way connectors, the ‘flex’
connectors should be used where there is highly undulating ground.
METAL U-PIN• Metal U-pin connectors should be used in conjunction with other
connectors when LibertyMats™ are installed on inclines or slopes
LIBERTYMAT™ HEAVY DUTY TEMPORARY ACCESS MAT
• Material: 100% Recycled or Virgin High Density Polyethylene (HDPE)• Size: 94.88” x 47.20” x .47”• Weight: 77 lb.
TECHNICAL PRODUCT INFORMATION: For use as a technical guide only
MECHANICAL PROPERTIES UNIT HDPE
Tensile Strength MPa 23-26
Flexural Strength MPa 25-28
Flexural Modulus MPa 1936-1967
Charpy Notched Impact Strength kJ/m2 5-6
Poisson’s Ratio (theoretical) 0.35-0.38
Compression Testing(max value before test terminated)
Tons 250
To view our full line of Safety Products, visit us at www.checkersindustrial.com or call 1-800-438-9336.
Dedicated to saving lives and protecting assets
Dedicated to saving lives and protecting assets.
*Load performance depends on ground conditions as well as the weight and type of vehicles and plant. Checkers®, its agents or employees are not liable for any damage to existing ground or property through use of LibertyMat™.
The sale or hire of all temporary access mats are subject to Checkers®’ standard Terms and Conditions. These are available from our website checkersindustrial.com or by telephoning our sales office.
HEALTH AND SAFETY INFORMATION:
GENERAL PROPERTIES UNIT HDPE
Density kg/m3 940-965
Shrinkage % 2-4
Water Absorption % 0.01
Thermal Expansion e-6/K 110-130
Thermal Conductivity W/m.K 0.46-0.52
Specific Heat J/kg.K 1800-2700
Melting Temperature ˚F 226 - 273
Glass Temperature ˚F -166
Service Temperature ˚F -22 - +185
Resistivity Ohm.mm2/m 5e+17-1e+21
Breakdown Potential kV/mm 17.7-19.7
Dielectric Loss Factor 0.0005-0.0008
Friction Coefficient 0.25-0.30
Refraction Index 1.52-1.53
GENERAL UNIT
Critical Hazards to Man and Environment None
Environment The disposal of the material presents no danger regarding toxicological or ecological considerations. Due to low water solubility, bio-availability unlikely.
Solubility in Water Insoluble
Regulatory Not classified as hazardous under transport regulations.
SAFETY PROPERTIES UNIT
Melting Point Crystalline Melt Temperature 226 - 273˚F
Ignition Temperature > 680˚F
Thermal Decomposition > 734˚F
Stability and Reactivity No possibility of degradation under normal circumstances.Degradation will only occur above the decomposition temperature.
Toxicology Not harmful to health under normal conditions.
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.comwww.checkersindustrial.com
Dedicated to saving lives and protecting assets.
OUTRIGGERSHEAVY DUTY CRANE PADS
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
OUTRIGGER HEAVY DUTY CRANE PADS
Being made from high quality polyethylene, Checkers’ outrigger crane pads will not splinter or absorb water. They are strong, durable, chemical and oil resistant, long lasting, easy to store and clean.
“Carry handles” make Checkers’ outriggers easy to handle and install. The unique design allows each pad to adapt to the ground, providing a safe working platform for heavy plant and returning to its original shape once work is complete.
Despite being incredibly strong and durable, the pads are lightweight. making them easy to move around.
Being impermeable to water, Checkers’ outrigger crane pads can be used in all weather conditions.
Simply, Checkers’ outrigger crane pads are an efficient and cost effective solution for outrigger support.
• Wide Range of Standard Sizes to Suit Project Need, Load and Requirements• Optional - Customized Size, Shape, Color or Corporate Branding • ”Carry Handles” - Easy to Transport and Install• No Splintering -Unbreakable Under Normal Working Conditions• No Absorption of Water - Can Be Used in All Weather Conditions• High Resistance to Vertical Pressure• Long Lasting With a Superior Life Span Compared to Other Materials
FEATURES:• Manufactured from 100% Recycled Materials• Tough and Durable Construction• No Splintering• No Absorption of Water• Choice of Standard or Custom Sizes • Customized Colors or Company Branding
ADVANTAGES:
To prevent accidents and comply with the health and safety regulations of personnel operating cranes, lifting equipment and aerial platforms, outrigger crane pads are an essential component of the crane and plant hire industry.
Checkers’ outrigger crane pads are made from a mix of 100% recycled High Molecular Weight and Ultra High Molecular Weight Polyethylene, making them ideal for use with cranes, hiabs and aerial work platforms.
Checkers’ outrigger crane pads provide a cushioned support area for outriggers, giving a stable load platform, preventing ground damage, while delivering a safe and balanced area to work on.
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
From the Experts in Industrial Safety
STANDARD SIZES• A wide selection of sizes and weight loadings are available
in standard, complete with rope carry handle. • See back page - Standard outriggers are made from a mix
of 100% recycled High Molecular Weight and Ultra High Molecular Weight Polyethylene.
CUSTOM SHAPES• Our standard range of outriggers are square but
we can customize your outrigger shape - round / rectangular / with or without foot recess
CUSTOM DESIGNS• Color - 100% recycled black
or virgin colored Polyethylene• Customize handles - quantity / position / type• Branding - emboss logo / address etc.
SUPERIOR LIFE SPAN COMPARED TO OTHER MATERIALS
100% Recycled Black Polyethylene
Virgin Colored Polyethylene
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
OUTRIGGERS HEAVY DUTY CRANE PADS STANDARD SIZES:
To view our full line of Safety Products, visit us at www.checkersindustrial.com or call 1-800-438-9336.
Dedicated to saving lives and protecting assets
Dedicated to saving lives and protecting assets.
MODEL DIMENSIONS WEIGHT (lbs.) CAPACITY (ton) FROM TOton/m2
ZSP-OP20-3 7.87 in. x 7.87 in. x 1.18 in. 2.2 4 1.5 4.5
ZSP-OP25-3 9.84 in. x 9.84 in.x 1.18 in. 3.97 4.5 2 5.5
ZSP-OP30-2 11.81 in. x 11.81 in. x .79 in. 3.75 5 2.5 6.5
ZSP-OP30-3 11.81 in. x 11.81 in. x 1.18 in. 5.51 7 4 9.5
ZSP-OP40-4 15.75 in. x 15.75 in. x 1.57 in. 13.23 10 12.5 18.5
ZSP-OP40-5 15.75 in. x 15.75 in. x 1.97 in. 17.64 11 14.5 20
ZSP-OP50-4 19.96 in. x 19.69 in. x 1.57 in. 22.05 15 18 23
ZSP-OP50-6 19.96 in. x 19.69 in. x 2.36 in. 33.07 20 22 50
ZSP-OP60-5 23.62 in. x 23.62 in. x 1.97 in. 39.68 23 45 70
ZSP-OP60-6 23.62 in. x 23.62 in. x 2.36 in. 46.3 25 65 85
ZSP-OP70-6 27.56 in. x 27.56 in. x 2.36 in. 63.93 30 80 100
ZSP-OP80-5 31.5 in. x 31.5 in. x 1.97 in. 70.55 32 80 100
ZSP-OP80-6 31.5 in. x 31.5 in. x 2.36 in. 83.78 35 90 130
ZSP-OP100-4 39.37 in. x 39.37 in. x 1.57 in. 85.98 37 80 100
ZSP-OP100-5 39.37 in. x 39.37 in. x 1.97 in. 105.82 40 120 150
ZSP-OP100-6 139.37 in. x 39.37 in. x 2.36 in. 127.87 50 Contact us for more details
Contact us for more details
ZSP-OP100-8 39.37 in. x 39.37 in. x 3.15 in. 171.96 80 Contact us for more details
Contact us for more details
ZSP-OP120-8 47.24 in. x 47.24 in. x 3.15 in. 253.53 100 Contact us for more details
Contact us for more details
www.checkersindustrial.com
Dedicated to saving lives and protecting assets.
TEMPORARY ACCESS& GROUND PROTECTION
As designers, manufacturers and suppliers of temporary access and ground protection solutions, we aim to provide our customers with innovative ‘best in class’ products delivering the highest levels of performance, value and safety. We are committed to ensuring our products meet the ever changing and demanding conditions within the civil engineering, transmission, renewable energy, oil and gas, infrastructure, ground work and leisure event industries.
Our solutions are designed to meet health and safety regulations, avoid environmental damage and save time and project costs. Sustain-ability and environmental protection are both at the forefront of Checkers®’ mission, as we strive to minimize the impact of our business on the natural environment and the community at large. Our products are manufactured from 100% recycled plastics and waste materi-als at ‘end of life,’ diverting these useful materials away from landfills.
TUFFTRAK® STANDARD: TUFFTRAK® XL:
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
• Size : 118.11 in. x 98.43 in. x 1.85 in.• Weight: 650.36 lbs.
TuffTrak® is the ultimate heavy duty road mat for temporary roadways and work areas, with a weight loading to 150* tons, dependent on ground conditions. TuffTrak® is the market’s leading 100% solid compression molded mat and is chemically inert making it ideal for use on eco-sensitive sites. Being solid means that it cannot be punctured - avoiding the intake of liquids and reducing the threat of invasive species or cross contamination between sites. TuffTrak® incorporates dual grip surfaces, featuring optimal rugged grip from Checkers®’ unique chevron traction® surface and a low profile pedestrian friendly surface ideal for use on work pads and walkways.
• Size : 161.1 in. x 98.43 in. x 1.83 in.• Weight: 895.8 lbs.
TUFFTRAK® STANDARD & TUFFTRAK®XL HEAVY DUTY ROAD MATS
TuffTrak® Lite combines the market leading performance associated with TuffTrak® while providing operational and financial benefits in handling and installation due to a vastly reduced weight.
The rugged, yet pedestrian-friendly traction surface on TuffTrak® Lite reduces slippage, helping deliver forward traction for efficient and safe use with heavy equipment, vehicles and site personnel. It is ideal for use where temporary roadways and work areas are required but smaller manhandleable mats cannot support the heavy plant or equipment.
• Size : 118.11 in. x 98.43 in. x 1.25 in. • Weight: 407.86 lbs.
TUFFTRAK® LITE HEAVY DUTY ROAD MATS
LIBERTY MAT™
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
From the Experts in Industrial Safety
Supporting loads up to 80 tons, Liberty Mat™ is the ultimate heavy duty man-handleable mat for temporary roadways and work areas. Liberty Mat™ is essential for the construction, civil engineering and ground work industries.
Made from tough 100% recycled or virgin high density Polyethylene (HDPE), Liberty Mat™ is the market leader for temporary access and ground protection over soft or sensitive ground. Liberty Mat™ significantly reduces damage to heritage and eco-sensitive areas, avoiding the need for reinstatement once the project is complete.
• Size: 94.88 in. x 47.24 in. x .47 in. • Weight: 77.16 lbs.
ECONOMAT MB™ Economat MB™ has been specifically developed as an effective and efficient
alternative to construction plywood providing a low cost, easy to deploy and reusable temporary access and ground protection solution.
Economat MB™ is resistant to adverse weather making it ideal for use in snow, ice, frost or damp conditions. Made from 100% recycled Low Density Polyethylene, Economat MB™ can be re-used time and again providing considerable long term cost savings over plywood.
• Size: 94.44 in. x 47.24 in. x .47 in. • Weight: 70.5 lbs.
GEOGRID® GeoGrid® cellular paving system enables the fast and efficient implementation of
ground reinforcement and stabilization. GeoGrid®’s unique patented design offers the combination of excellent cellular strength and weight load capability (up to 500 tons/m2) while allowing for optimal expansion and contraction, which avoids the risk of surface deformation in hot or cold climates. The cellular design of the grids allows the dispersion of excess rain or flood water which makes it ideal for integration with Sustainable Urban Drainage Systems (SUDS) and in areas prone to flooding or with water dispersion problems.
• Size: 19.49 in. x 19.49 in. x 1.57 in. • Weight: Standard - 2.43 lbs per grid 9.7 lb/m2 • Weight: Premium - 3.53 in. per grid 151.87 lb/m2
To view our full line of Safety Products, visit us at www.checkersindustrial.com or call 1-800-438-9336.
Dedicated to saving lives and protecting assets
Dedicated to saving lives and protecting assets.
TRENCHSAFE™• Made from single piece, glass reinforced SMC and
subject to ISO9001 accredited quality control• Strengthened ribbed underside - Pre-pressed
anchor points in each corner• Easy to clean and maintain• DETR Safety at Streetworks and Roadworks Code
of Practice compliant• BS EN 124 and Safe Working Practice compliant
OUTRIGGER PADS• Made from 100% recycled polyethylene • Does not absorb water • Long lasting - extended life compared to other
materials• For use with crane and aerial work platform
industries• Essential component of the hire industry• Stable load platform - preventing ground damage• Handy carry handles make transport easy• Variety of size options to suit wide range of weight
loads
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.comwww.checkersindustrial.com
Dedicated to saving lives and protecting assets.
TRENCHSAFE™
PATHWAY SAFETY PLATEFOR PEDESTRIAN USE
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
TRENCHSAFE™ PATHWAY SAFETY PLATEFEATURES:
Certified to 1653.47 lbs. Independently tested at both Lancaster University and SGS (China)
to a maximum point load of 2204.62 lbs.
TRENCHSAFE™ 12/8:• Dimensions: Length: 47.24 in. • Width: 31.5 in.• Thickness: .98 in.• Weight: 1102.31 lbs.• Transportation: Quantity per pallet, 40• Capable of withstanding a point load weight of
up to 1102.31 lbs. over a 27.56 in. span
• Non-slip leading edge and unique chevron traction® surface greatly reduces slip, even in adverse conditions 1
• Made from single piece, solid color, glass reinforced SMC and subject to ISO9001 accredited quality control
• Pre-pressed anchor points at each corner to fix TrenchSafe™ into position
• Strengthened ribbed underside• Easy to clean and maintain• Reduced risk of theft - no scrap value• Easy to install, maximum of two man lift and no specialist
equipment required
• DETR Safety at Streetworks and Roadworks Code of Practice compliant
• BS EN 124 and Safe Working Practice compliant• Ideally suited to cover apertures, bores or trenches during
construction or repair work for utility, excavations, cabling and maintenance projects
• Substantially lighter than steel covers• Substantially stronger than wooden plates• Tough and durable construction• Available in two sizes• Optional corporate colors and company branding
Strengthened and ribbed underside Increases weight load capabilities Reduces flexing
Knock-out undersideDiameter 1 in. / Recess wall thickness 0.47 in. Knock-out thickness 0.05 in.
Anchor pointknock-outDiameter 1 in. Recesses 0.04 in.
Take health & safety directives into consideration when installing TrenchSafe™. Always pin TrenchSafe™ via pre-pressed anchor points while in use.
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
From the Experts in Industrial Safety
TRENCHSAFE™ 16/12:• Dimensions: Length: 63 in. Width: 47.24 in.• Thickness: 1 in.• Weight: 63.93 lbs.• Transportation: Quantity per pallet, 36• Capable of withstanding a point load weight of
up to 1102.31 lbs. over a 35.43 in. span
Certified to 1653.47 lbs. Independently tested at both Lancaster University and SGS (China)
to a maximum point load of 2204.62 lbs.
Strengthened and ribbed undersideIncreases weight load capabilities Reduces flexing
Knock-out undersideDiameter 1 in.Recess wall thickness 0.05 in.Knock-out thickness 0.05 in.
Anchor pointknock-outDiameter 1 in. Recesses 0.04 in.
Take health & safety directives into consideration when installing TrenchSafe™. Always pin TrenchSafe™ via pre-pressed anchor points while in use.
TOUGH AND DURABLECONTRUCTION
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
TRENCHSAFE™ PATHWAY SAFETY PLATE FOR PEDESTRIAN USE: • Material: Glass reinforced SMC plastic• Color: Yellow
(Option for corporate colors and company branding)
TECHNICAL PRODUCT INFORMATION:
To view our full line of Safety Products, visit us at www.checkersindustrial.com or call 1-800-438-9336.
Dedicated to saving lives and protecting assets
Dedicated to saving lives and protecting assets.
*Load performance depends on ground conditions as well as the weight and type of vehicles and plant. Checkers®, its agents or employees are not liable for any damage to existing ground or property through use of TrenchSafe™.
NOTE: To reduce risk of injury, it is important to take health & safety directives into consideration when handling and installing TrenchSafe™.
To avoid any movement of the safety plate it is recommended to always pin TrenchSafe™ via pre-pressed anchor points while in use.
DIMENSIONS TRENCHSAFE™ 12/8 TRENCHSAFE™ 16/12
LENGTH 47.24 in. 63 in.
WIDTH 31.5 in. 47.24 in.
THICKNESS 1 in. 1 in.
WEIGHT 26.9 lbs. 64 lbs.
1102.31 LB. POINT LOAD over a 27.56 in. span over a 35.43 in. span
TESTED POINT LOAD 2866.01 lbs. 2204.62 lbs.
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.comwww.checkersindustrial.com
Dedicated to saving lives and protecting assets.
TUFFTRAK®
HEAVY DUTY ROAD MAT
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
TUFFTRAK® HEAVY DUTY ROAD MAT
HEAVY DUTY ROAD MAT• TuffTrak® is the ultimate heavy duty road mat for temporary roadways
and work areas for heavy plant, machinery and multiple vehicles with a weight loading to 150* tons (dependent on ground conditions).
INCREDIBLY TOUGH & FLEXIBLE• Made from tough High Density (HD) or Ultra High Molecular Weight (UHMW) Polyethylene, TuffTrak® is the market’s
leading 100% solid compression molded mat and is chemically inert making it ideal for use on eco-sensitive sites. Being solid means that it cannot be punctured - avoiding the intake of liquids and reducing the threat of invasive species or cross contamination between sites.
CHEVRON TRACTION® SURFACE• The engineered, unique Chevron Traction® surface delivers ultimate grip and helps to dispel mud whilst vehicles traverse over them.• The chevron nub design reduces sideways movement and slippage delivering optimal forward traction for heavy vehicles and
machinery.
LOGISTICS• TuffTrak® is lighter to transport than most alternative temporary road mats. More mats can, therefore, be loaded on to trucks or in
to containers, reducing transportation costs.
ADVANTAGES:• Heavy duty road mat• Incredibly tough & flexible• Unique dual grip capability - Chevron traction® surface - Low profile traction• Solid one piece construction • Unique chevron traction® surface• Lower transport cost than other mats• Tough durable working areas and temporary roads for heavy plant,
equipment and multiple vehicles• Protects against severe rutting and eco-damage to ground and
sensitive sites• Supports health and safety objectives• A reversible low profile surface for drilling rigs, work pads, depot areas
and helipads• Connection options for different terrain & equipment• Non-conductive - ideal for use on transmission projects• Designed and manufactured in the UK and Europe
FEATURES:
*Compression tested at National Physical Laboratory, UK
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
From the Experts in Industrial Safety
PRODUCT SPECIFICATIONS:TUFFTRAK® HEAVY DUTY ROAD MAT• Material: High Density Polyethylene or
Ultra High Molecular Weight Polyethylene • Size: 9.84 ft. x 8.20 ft. x 1.5 in.;
overall thickness 1.85 in.• Weight: 650 lbs.
APPLICATIONS:• Civil Engineering
and Construction• Infrastructure
and Utilities Maintenance
• Military Sites• Events• Transmission• Oil and Gas
Mat lifting points
HI TENSILE H-VIZ ‘FLEX’ CONNECTORS FOR INCREASED SAFETY AND PERFORMANCE OVER UNDULATING GROUND• Material : Steel and nylon• Size: 9.45 in. x 2.76 in.• Weight: 0.33 lbs.
METAL CONNECTORS FOR HEAVY EQUIPMENT• Material : Steel• Size: 10.24 in. x 1.57 in. x 0.20 in.• Weight: 0.77 lbs.
To request a full installation guide please call Checkers®.
CONNECTION SYSTEMS:
• TuffTrak® is fast to install with a simple ‘drop in’ M16 bolt system.
• TuffTrak® also offers a range of connectors including high tensile hi-viz ‘flex’ straps for increased safety and deployment over undulating ground.
• The traction surface provides grip for use in pedestrian applications as well as vehicular use.
• With a lighter weight TuffTrak® is ideal when the weather or round conditions rapidly deteriorate.
TuffTrak® bracket and lifting lug
TuffTrak®colored Virgin
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
TUFFTRAK® HEAVY DUTY ROAD MAT• Material: High Density Polyethylene or Ultra High Molecular
Weight Polyethylene • Size: 9.84 ft. x 8.20 ft. x 1.5 in.; overall thickness 1.85 in.• Weight: 650 lbs.
TECHNICAL PRODUCT INFORMATION: For use as a technical guide only
To view our full line of Safety Products, visit us at www.checkersindustrial.com or call 1-800-438-9336.
Dedicated to saving lives and protecting assets
Dedicated to saving lives and protecting assets.
HEALTH AND SAFETY INFORMATION:
GENERAL
Critical Hazards to Man and Environment None
Environment The disposal of the material presents no danger regarding toxicological or ecological considerations. Due to low water solubility, bio-availability unlikely.
Solubility in Water Insoluble
Regulatory Not classified as hazardous under transport regulations.
SAFETY PROPERTIES
Melting Point Crystalline Melt Temperature 275 - 293˚F
Ignition Temperature > 680˚F
Thermal Decomposition > 734˚F
Stability and Reactivity No possibility of degradation under normal circumstances.Degradation will only occur above the decomposition temperature.
Toxicology Not harmful to health under normal conditions.
WEIGHT LOADING 150 tons*
MATERIALPremium recycled or virgin High Density (HD) or Ultra High Molecular Weight (UHMW) Polyethylene
Choice of colors for Virgin or UHMWPEAdditive packages for UV protection and static dissipation are available
MATERIAL STRENGTH Compression loads in excess of 1500 psi (110 kg/cm2) have been recorded during tests undertaken at an accredited UK laboratory.
TEMPERATURE VARIATIONSCheckers® products are used globally in many geographic locations covering a wide range of temperatures.
The recommended operating temperature range is -58 ˚F to 176 ˚F.For severe cold climates TuffTrak® made from UHMWPE material is advised
COLORS AVAILABLE Black for recycled HD or UHMW polyethylene. Choice of colors for Virgin HD or UHMW polyethylene.
CONNECTIVITY Easy to install ‘Drop in’ M16 bolt system. Metal connectors for heavy equipment.High tensile, hi-viz ‘flex’ connectors for increased safety and performance over undulating ground
TRACTION SURFACE TufftTrak® incorporates a pedestrian friendly low profile traction surface combined with a micro traction on both upper and lower surfaces reducing the risk of slippage and delivering forward traction for use with heavy plant, vehicles and site personnel.
DUAL GRIP CAPABILITYThe unique high profile chevron traction® surface delivers ultimate grip and reduces sideways movement and slippage, delivering optimal
forward traction for heavy plant, machinery and vehicles.Low profile traction surface on reverse of mat
ENVIRONMENTAL FEATURES Weatherproof, water and chemical resistant. HD and UHMW polyethylene are resistant to acids, alkalis and solvents.
LOGISTICS 80 TuffTrak® mats per standard EU curtain sided trailer, 44.62 loading feet. Up to 24 tons. (Comprising 16 pallets of 5 mats)
CUSTOMIZATION Corporate logo and contact details can be added, subject to minimum order.
*Load performance depends on ground conditions as well as the weight and type of vehicles and plant. Checkers®, its agents or employees are not liable for any damage to existing ground or property through use of TuffTrak®.
The sale or hire of all temporary access mats are subject to Checkers®’ standard Terms and Conditions. These are available from our website checkersindustrial.com or by telephoning our sales office.
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.comwww.checkersindustrial.com
Dedicated to saving lives and protecting assets.
TUFFTRAK® LITELIGHTWEIGHT HEAVY DUTY
ROAD MAT
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
TUFFTRAK® LIGHTWEIGHT HEAVY DUTY ROAD MAT
LIGHTWEIGHT HEAVY DUTY ROAD MAT• Weighing just 407.86 lbs., TuffTrak® Lite compliments the heavy duty TuffTrak® rang by combining the market leading performance
associated with TuffTrak® and providing operational and financial benefits in handling and installation due to a vastly reduced weight.
INCREDIBLY TOUGH & FLEXIBLE• Made from tough 100% recycled High Density (HD) or Ultra High Molecular Weight (UHMW) Polyethylene, TuffTrak® Lite is manufactured as a solid compression molded mat that is chemically inert (ideal for use on eco-sensitive sites). Being a solid
one piece construction means that TuffTrak® Lite cannot be punctured - avoiding the intake of liquids and reducing the threat of invasive species or cross contamination between sites. Designed to flex, TuffTrak® Lite adapts to varied ground conditions yet provides a weight loading to over 100* tons, depending on conditions.
LOW PROFILE TRACTION SURFACE• The unique design of TuffTrak® Lite provides a sought after solution to temporary roadways by combining lighter weight with the
grip and ground protection offered from a heavy duty road mat. The rugged, yet pedestrian friendly traction surface on TuffTrak® Lite reduces slippage, helping deliver forward traction for efficient and safe use with heavy plant, vehicles and site personnel, making it ideal for use as temporary roadways and work areas.
LOGISTICS• As a heavy duty road mat, TuffTrak® Lite is lighter to transport than most alternative temporary road mats with comparable
performance. Therefore, more mats can be loaded on to trucks or in to containers, substantially reducing transportation costs.
ADVANTAGES:• Renowned TuffTrak® performance• Lighter in weight than other heavy duty road mats with comparable
performance• Incredibly tough & flexible• Low traction surface for efficient and safe use with heavy plant vehicles
and site personnel• Connection options for all terrains• Designed to provide lighter weight heavy duty access than other mats
with comparable performance• Tough and durable for work areas and temporary roads• Ideal for use with heavy plant, vehicles and site personnel• Pedestrian friendly traction® surface for drilling rigs, work pads, depot
areas and helipads • Solid one piece construction avoids intake of liquids and contaminants• Supports health & safety objectives• Substantially lower transport costs than other mats • Protects against severe rutting and eco-damage to sensitive sites• Connection options for different terrain & equipment• Non-conductive - ideal for use on transmission projects• Designed and manufactured in the UK and Europe
FEATURES:
*Compression tested at National Physical Laboratory, UK
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
From the Experts in Industrial Safety
PRODUCT SPECIFICATIONS:TUFFTRAK® LITE - LIGHTWEIGHT HEAVY DUTY ROAD MAT• Material: High Density Polyethylene or
Ultra High Molecular Weight Polyethylene• Size: 9.84 ft. x 8.20 ft. x 1.25 in.• Weight: 407.86 lbs.
APPLICATIONS:• Civil Engineering
and Construction• Infrastructure
and Utilities Maintenance
• Military Sites• Events• Transmission• Oil and Gas
TuffTrak® Lite bracket and lifting lug
Mat lifting points
HI TENSILE H-VIZ ‘FLEX’ CONNECTORS FOR INCREASED SAFETY AND PERFORMANCE OVER UNDULATING GROUND• Material : Steel and nylon• Size: 9.45 in. x 2.76 in. • Weight: 0.33 lbs.
METAL CONNECTORS FOR HEAVY EQUIPMENT• Material : Steel• Size: 10.24 in. x 1.57 in. x 0.20 in.• Weight: 0.77 lbs.
To request a full installation guide please call Checkers®.
CONNECTION SYSTEMS:
• TuffTrak® Lite is fast to install with a simple ‘drop in’ M16 bolt system.
• TuffTrak® Lite also offers a range of connectors including high tensile hi-viz ‘flex’ straps for increased safety and deployment over undulating ground.
• The traction surface provides grip for use in pedestrian applications as well as vehicular use.
• With a lighter weight TuffTrak® Lite is ideal when the weather or round conditions rapidly deteriorate.
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
TUFFTRAK® LITE LIGHTWEIGHT HEAVY DUTY ROAD MAT• Material: High Density Polyethylene or
Ultra High Molecular Weight Polyethylene• Size: 9.84 ft. x 8.20 ft. x 1.25 in.• Weight: 407.86 lbs.
TECHNICAL PRODUCT INFORMATION: For use as a technical guide only
To view our full line of Safety Products, visit us at www.checkersindustrial.com or call 1-800-438-9336.
Dedicated to saving lives and protecting assets
Dedicated to saving lives and protecting assets.
HEALTH AND SAFETY INFORMATION:
GENERAL
Critical Hazards to Man and Environment None
Environment The disposal of the material presents no danger regarding toxicological or ecological considerations. Due to low water solubility, bio-availability unlikely.
Solubility in Water Insoluble
Regulatory Not classified as hazardous under transport regulations.
SAFETY PROPERTIES
Melting Point Crystalline Melt Temperature 248- 284˚F (135 -145˚C)
Ignition Temperature > 680˚F (360˚C)
Thermal Decomposition > 734˚F (390˚C)
Stability and Reactivity No possibility of degradation under normal circumstances.Degradation will only occur above the decomposition temperature.
Toxicology Not harmful to health under normal conditions.
WEIGHT LOADING 100 tons*
MATERIALPremium recycled or virgin High Density (HD) or Ultra High Molecular Weight (UHMW) Polyethylene
Choice of colors for Virgin or UHMWPEAdditive packages for UV protection and static dissipation are available
MATERIAL STRENGTH Compression loads in excess of 1500 psi (110 kg/cm2) have been recorded during tests undertaken at an accredited UK laboratory.
TEMPERATURE VARIATIONS Checkers® products are used globally in many geographic locations covering a wide range of temperatures.
COLORS AVAILABLE Black for recycled HD or UHMW polyethylene. Choice of colors for Virgin HD or UHMW polyethylene.
CONNECTIVITYEasy to install ‘Drop in’ M16 bolt systemMetal connectors for heavy equipment
High tensile, hi-viz ‘flex’ connectors for increased safety and performance over undulating ground
TRACTION SURFACETufftTrak® Lite incorporates a pedestrian friendly low profile traction surface combined with a
micro traction on both upper and lower surfaces reducing the risk of slippage and delivering forward traction for use with heavy plant, vehicles and site personnel.
ENVIRONMENTAL FEATURES Weatherproof, water and chemical resistant. HD and UHMW polyethylene are resistant to acids, alkalis and solvents.
LOGISTICS 128 TuffTrak® Lite mats per standard EU curtain sided trailer, 44.62 loading feet.up to 24 tons. (consists of 12 pallets of 6 mats and 8 pallets of 7 mats)
CUSTOMIZATION Corporate logo and contact details can be added, subject to minimum order.
*Load performance depends on ground conditions as well as the weight and type of vehicles and plant. Checkers®, its agents or employees are not liable for any damage to existing ground or property through use of TuffTrak® Lite.
The sale or hire of all temporary access mats are subject to Checkers®’ standard Terms and Conditions. These are available from our website checkersindustrial.com or by telephoning our sales office.
www.checkersindustrial.com
Dedicated to saving lives and protecting assets.
TUFFTRAK®XLHEAVY DUTY ROAD MAT
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
TUFFTRAK®XL HEAVY DUTY ROAD MAT
HEAVY DUTY ROAD MAT• TuffTrak®XL is the ultimate heavy duty road mat for temporary
roadways and work areas for heavy equipment, machinery and multiple vehicles with a weight loading to over 330,693 lbs. (150,000 kg) (dependent on ground conditions*).
INCREDIBLY TOUGH & FLEXIBLE• Unlike other composite mats, TuffTrak®XL is made from tough High Density (HD) Polyethylene. TuffTrak®XL is the
market’s leading 100% solid compression molded mat and is chemically inert making it ideal for use on eco-sensitive sites. Being solid means that it cannot be punctured - avoiding the intake of liquids and reducing the threat of invasive species or cross contamination between sites.
CHEVRON TRACTION® SURFACE• The engineered, unique Chevron Traction® surface delivers ultimate grip and helps to dispel mud whilst vehicles traverse over them.• The chevron nub design reduces sideways movement and slippage delivering optimal forward traction for heavy vehicles and
machinery.
LOGISTICS• TuffTrak®XL is lighter to transport than most alternative composite and other matting products. More mats can, therefore, be
loaded on to trailers or in to containers, reducing transportation costs.
ADVANTAGES:• Heavy duty road mat• Incredibly tough & flexible• Unique dual grip capability - Chevron traction® surface - Low profile traction• Solid one piece construction • Unique Chevron Traction® surface• Lower transport unit area cost than other composite mats• Tough durable working areas and temporary roads for heavy equipment
and multiple vehicles• Protects against severe rutting and eco-damage to ground and
sensitive sites• Supports health & safety objectives• A reversible low profile surface for drilling rigs, work pads, depot areas
and helipads• Connection options for different terrain and equipment• Non-conductive - ideal for use on transmission projects• ACME thread connection - quick and robust
FEATURES:
*Compression tested at National Physical Laboratory, UK
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
TUFFTRAK®XL IS FAST TO INSTALL WITH A SIMPLEDROP IN ACME BOLT.
From the Experts in Industrial Safety
PRODUCT SPECIFICATIONS:TUFFTRAK®XL HEAVY DUTY ROAD MAT• Material: Ultra High Molecular Weight
Polyethylene (UHMWPE)• Size: 13’ 5” x 6’ 8” x 1.85”• Weight: 794 lbs
APPLICATIONS:• Civil Engineering
and Construction• Infrastructure
and Utilities Maintenance
• Military Sites• Events• Transmission• Oil and Gas
• ACME bolt- strong, easy and fast to thread• ACME bolt - helps push out mud and grit• Recessed connection area to maintain low profile• Connectors flex to aid connection for uneven ground• Metal connectors for heavy equipment• High tensile, hi-viz ‘flex’ connectors for increased
safety and performance over undulating ground
To request a full installation guide please call Checkers®.
CONNECTION SYSTEMS:
• TuffTrak®XL is fast to install with a simple drop in ACME bolt.
• The unique chevron traction® surface is regarded as the most effective in the market and is ideal when the weather or ground conditions rapidly deteriorate.
TuffTrak®XL ACME thread connection
CHECKERS INDUSTRIAL SAFETY PRODUCTS • 800-438-9336 • www.checkersindustrial.com
TUFFTRAK®XL HEAVY DUTY ROAD MAT• Material: High Density (HD) Polyethylene• Size: 13’ 5” (408.94 cm) x 6’ 8” (203.2 cm) x 1.85” (4.70 cm);
overall thickness 2.125” (5.40 cm)
TECHNICAL PRODUCT INFORMATION: For use as a technical guide only
To view our full line of Safety Products, visit us at www.checkersindustrial.com or call 1-800-438-9336.
Dedicated to saving lives and protecting assets
Dedicated to saving lives and protecting assets.
HEALTH AND SAFETY INFORMATION:
GENERAL
Critical Hazards to Man and Environment None
Environment The disposal of the material presents no danger regarding toxicological or ecological considerations. Due to low water solubility, bio-availability unlikely.
Solubility in Water Insoluble
Regulatory Not classified as hazardous under transport regulations.
SAFETY PROPERTIES
Melting Point Crystalline Melt Temperature 248- 284˚F (135 -145˚C)
Ignition Temperature > 680˚F (360˚C)
Thermal Decomposition > 734˚F (390˚C)
Stability and Reactivity No possibility of degradation under normal circumstances.Degradation will only occur above the decomposition temperature.
Toxicology Not harmful to health under normal conditions.
WEIGHT LOADING 150 tons*
MATERIALPremium recycled or virgin High Density (HD) or Ultra High Molecular Weight (UHMW) Polyethylene
Choice of colors for Virgin or UHMWPEAdditive packages for UV protection and static dissipation are available
MATERIAL STRENGTH Compression loads in excess of 1500 psi (110 kg/cm2) have been recorded during tests undertaken at an accredited UK laboratory.
TEMPERATURE VARIATIONS Checkers® products are used globally in many geographic locations covering a wide range of temperatures. The recommended operating temperature range is -58 ˚F to 176 ˚F.
COLORS AVAILABLE Black for recycled. Choice of colors for virgin.
CONNECTIVITY ‘Drop in’ ACME bolt. Connectors for uneven ground. Metal connectors for heavy equipmentHigh tensile, hi-viz ‘flex’ connectors over undulating ground
DUAL GRIP CAPABILITYThe unique high profile chevron traction® surface delivers ultimate grip and reduces sideways movement and slippage,
delivering optimal forward traction for heavy machinery, equipment and vehicles.Low profile traction surface on reverse of the mat.
ENVIRONMENTAL FEATURES Weatherproof, water and chemical resistant. HD and UHMW polyethylene are resistant to acids, alkalis and solvents.
LOGISTICS 60 TuffTrak®XL per 48,000 lb flatbed trailer.50 TuffTrak®XL per ocean container.
CUSTOMIZATION Corporate logo and contact details can be added, subject to minimum order.
*Load performance depends on ground conditions as well as the weight and type of vehicles and plant. Checkers®, its agents or employees are not liable for any damage to existing ground or property through use of TuffTrak®XL .
The sale or hire of all temporary access mats are subject to Checkers®’ standard Terms and Conditions. These are available from our website checkersindustrial.com or by telephoning our sales office.