Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 1/39
This document is available on www.alma-alma.fr
OPERATING MANUAL
MU 7111 EN A
METERING SLEEVE for
FUEL METERING SYSTEM FMS OEM MTP
A 2019/01/30 Creation [PJV147] DSM PJ
Issue Date Modifications Written by Approved by
Do
cu
me
nt
ap
plic
ab
le f
or
so
ftw
are
fro
m v
ers
ion
40
48
+v1
.4.X
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 2/39
This document is available on www.alma-alma.fr
SOMMAIRE
1 GENERAL PRESENTATION AND DESCRIPTION .................................................................................. 4
2 OPERATING RECOMMENDATIONS ................................................................................................. 5
3 CONFIGURE, SET AND CALIBRATE THE FMS OEM MTP .................................................................... 5
3.1 Configure the FMS OEM MTP ................................................................................................. 5
3.2 Set the FMS OEM MTP ........................................................................................................... 6
3.3 Calibrate the FMS OEM MTP .................................................................................................. 6
4 USE THE FMS OEM MTP: USER MODE ............................................................................................ 7
4.1 Menu DELIVERY..................................................................................................................... 8
4.2 Menu PRINTING .................................................................................................................... 9
4.3 Menu DISPLAY .................................................................................................................... 11
4.3.1 Sub-menu TOTALISERS ............................................................................................................................. 11
4.3.2 Sub-menu MEMORISATION ..................................................................................................................... 11
4.4 Menu MAINTENANCE (Not used) ......................................................................................... 12
4.5 List of alarms ....................................................................................................................... 13
5 Set the FMS OEM MTP: SUPERVISOR MODE ................................................................................. 14
5.1 Menu CALIBRATION/ GAUGE ............................................................................................... 14
5.1.1 Menu ENTER CALIBRATION ...................................................................................................................... 14
5.1.2 Sub-menu LINEARISATION/FLOW ............................................................................................................ 14
5.2 Menu LANGUAGE ................................................................................................................ 15
5.3 Menu PRODUCT SETTINGS ................................................................................................... 15
5.4 Menu PRINTER SETTINGS ..................................................................................................... 16
5.5 Menu TIME ADJUSTMENT.................................................................................................... 16
5.6 Menu PARAMETERS: ........................................................................................................... 16
5.6.1 Sub-menu INDICATOR REFERENCE ........................................................................................................... 16
5.6.2 Sub-menu CONFIGURATION .................................................................................................................... 17
5.6.3 Sub-menu MEASURING SYSTEM .............................................................................................................. 18
5.7 Menu ICOM MENUS ............................................................................................................ 18
6 CONFIGURE THE FMS OEM MTP: METROLOGICAL MODE .............................................................. 19
6.1 Menu INDICATOR REFERENCE .............................................................................................. 19
6.2 Menu CONFIGURATION ....................................................................................................... 19
6.2.1 Sub-menu PRESET .................................................................................................................................... 19
6.2.2 Sub-menu UNIT AND ACCURACY ............................................................................................................. 19
6.2.2.1 With CONVERSION�OFF ............................................................................................................... 20
6.2.2.2 With CONVERSION�ON ................................................................................................................. 20
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 3/39
This document is available on www.alma-alma.fr
6.2.3 Sub-menu PRODUCTS .............................................................................................................................. 21
6.2.4 Sub-menu CONVERSION .......................................................................................................................... 22
6.2.5 Sub-menu PRINTER .................................................................................................................................. 23
6.2.6 Sub-menu FLOWING ................................................................................................................................ 23
6.2.7 Sub-menu AUTHORIZATION ..................................................................................................................... 24
6.3 Menu MEASURING SYSTEM ................................................................................................. 24
6.3.1 Sub-menu METER COEFFICIENT ............................................................................................................... 24
6.3.2 Sub-menu CORRECTION/ THOUSAND ...................................................................................................... 24
6.3.3 Sub-menu PULSES OUTPUT ...................................................................................................................... 25
6.3.4 Sub-menu TEMPERATURE ........................................................................................................................ 25
6.3.5 Sub-menu SETTINGS ................................................................................................................................. 25
6.3.5.1 Flowrate settings ............................................................................................................................ 25
6.3.5.2 Volume settings .............................................................................................................................. 25
6.3.5.3 Timing settings ................................................................................................................................ 26
6.4 Menu DATE AND TIME......................................................................................................... 26
ANNEX 1: FEATURES OF THE CONNECTED MICROCOMPT+ .................................................................... 27
ANNEX 2: PRINTINGS ........................................................................................................................... 37
RELATED DOCUMENTS......................................................................................................................... 39
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 4/39
This document is available on www.alma-alma.fr
1 GENERAL PRESENTATION AND DESCRIPTION
The installer can associate the METERING SLEEVE FMS OEM MTP to a PUMPING GROUP and a HOSE. The whole is a FUEL METERING SYSTEM MID type-approved: MEASURING SYSTEM FMS OEM type MTP.
The FMS OEM MTP can measure liquids other than water such as petrol, fuel, diesel or biofuels.
The METERING SLEEVE FMS OEM MTP contains these parts:
� A gas separator
� A sleeve upstream from the meter
� A sight glass
� An ALMA ADRIANE turbine meter
� An temperature sensor
� A downstream sleeve
� A non-return valve
A remote MICROCOMPT+ electronic calculator-indicator receives information from the pulse transmitter, the measuring device and the temperature probe.
The METERING SLEEVE FMS OEM MTP has one display:
Vm
L kg/m3
/min /h536
ADD ITIONAL INFORMATION
The MICROCOMPT+ has three pushbuttons:
CLEAR
Increment a blinking figure or letter
Come back to the previous step
Stop the measurement
MENU
Select a figure, a letter or a menu
OK
Validate the data
Volume indication
- Vm: volume in metering conditions
- Vb: volume converted to the reference temperature
Volume unit
Additional information (name of the product)
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 5/39
This document is available on www.alma-alma.fr
The FMS OEM can:
� Measure quantities of products
� Control the product temperature
� Show volume in metering conditions or volume converted to the reference temperature
� Manage measuring operations
� Manage faults
An optional function is available:
� A printer can print delivery tickets, internal totalisers, parameters, and summary and diary printings.
NOTE: The FMS OEM MTP shows the legally-binding information. The information printed by the printer has no metrological value.
2 OPERATING RECOMMENDATIONS
For a use of the FMS OEM MTP, make sure to meet the conditions that follow:
� If the gas evacuation pipe includes a manually-controlled valve that could reduce the gas separator efficiency, make sure that the valve remains in the open position during operation:
� By means of a sealing device
� Or automatically.
� Make sure the gas separator operates properly with a sight glass set up onto the separator or the pipe.
3 CONFIGURE, SET AND CALIBRATE THE FMS OEM MTP
3.1 Configure the FMS OEM MTP
You must configure the FMS OEM MTP during commissioning and sometimes during metrological controls. You must remove the seal as shown below. NOTE: Only approved persons are permitted to remove the seal.
Then you enter the METROLOGICAL mode. Details are available in the section CONFIGURE THE FMS OEM MTP: METROLOGICAL MODE.
See the verification manual MV 5015 for further information.
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 6/39
This document is available on www.alma-alma.fr
3.2 Set the FMS OEM MTP
You must set the FMS OEM MTP before any operation. To set the FMS OEM MTP, you need an ALMA RFID key that you put on the display as shown below:
Then you enter the SUPERVISOR mode. Details are available in the section SET THE FMS OEM MTP: SUPERVISOR MODE and annex 1.
See the verification manual MV 5015 for further information.
3.3 Calibrate the FMS OEM MTP
To calibrate the FMS OEM MTP, you need an ALMA RFID key that you put on the display as shown below:
Then you enter the SUPERVISOR mode. Details are available in the section SET THE FMS OEM MTP: SUPERVISOR MODE.
See the verification manual MV 5015 for further information.
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 7/39
This document is available on www.alma-alma.fr
4 USE THE FMS OEM MTP: USER MODE
READY
MAINTENANCE
VISUALISATION
PRINTING Printer in option
Not used
In USER mode, the MICROCOMPT+ displays a blinking figure which is the latest delivered quantity. The quantity is in liters (L), cubic meters (m3) or kilograms (Kg) depending on configuration.
The use of the FMS OEM MTP depends on the hardware configuration of the truck, the features and the configuration of the equipment carried out during commissioning:
Therefore, the user menu depends on several items:
� The distribution mode (free or preset)
� The temperature control (conversion of the volume)
� The optional printer.
During measurement, you can see the current volume (Vm or Vb, depending on the configuration of the main display in METROLOGICAL mode). During measurement, the following information may be displayed:
� The volume: Vb if current volume=Vm or Vm if current volume=Vb
� The instantaneous flowrate (m3/h or L/min)
� The temperature in °C
� The conversion factor
INSTANTANEOUS FLOW
047.4 L kg/m3
/min /h
TEMPERATURE
+18.6 L°Ckg/m3
/min /h
CONVERSION FACTOR
0.09981
with active option
with active option
CONVERTED VOLUME
993 L kg/m3
/min /h
Vb
According to the main display
VOLUME
998 L kg/m3
/min /h
Vm
OR
Back to normal display is automatic: DO NOT PRESS RED CLEAR BUTTON TO KEEP FROM
INTERRUPTING THE MEASURING OPERATION.
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 8/39
This document is available on www.alma-alma.fr
4.1 Menu DELIVERY
READY Choose product
STOP OPERATION 2MODE�FREE
2MODE�PRESETE ENTER PRESET
PRODUCT GO
PRODUCT GO
WAIT AUTHORIZATION START
WAIT AUTHORIZATION START
END OPERATION? TICKET
2
PRINTING
CONTINUE OPERATION? Operation
You can change the criteria: press the red pushbutton when START is displayed with the volume already discharged.
Non-systematic phase: Only if the FMS OEM MTP operates with a printer
Non-systematic phase: With active option
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 9/39
This document is available on www.alma-alma.fr
4.2 Menu PRINTING
The menu is available if the FMS OEM MTP operates with a printer (METROLOGICAL>PRINTER�ON).
TICKET: Print the ticket of the last measuring operation.
SUMMARY: Record a date and validate to print the summary of the measuring operations.
TOTALISERS: Print the products totalisers.
PARAMETERS: Print the recorded parameters.
EVENTS RECORDED: Record a date and validate to print the events recorded.
SUMMARY
EVENTS RECORDED
PARAMETERS
TOTALISERS
TICKETPRINTING
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 10/39
This document is available on www.alma-alma.fr
PRINTING ADD PAPER PRINTING... PRINTING FINISHEDTICKET
SUMMARY 21.06DATE (JJ.MM)
TOTALISERS
PARAMETERS
EVENTS RECORDED 21.06.18DATE (JJ.MM.AA)
ADD PAPER PRINTING... PRINTING FINISHED
ADD PAPER PRINTING... PRINTING FINISHED
ADD PAPER PRINTING... PRINTING FINISHED
ADD PAPER PRINTING... PRINTING FINISHED
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 11/39
This document is available on www.alma-alma.fr
4.3 Menu DISPLAY
This menu is available in standby mode or when you stop temporarily the measurement. You can see the totaliser value and the measurement results.
MEMORISATION
TOTALISERSVISUALISATION
4.3.1 Sub-menu TOTALISERS
GENERAL: Display the general totaliser
PRODUCTS: Display the secondary totalisers per product.
00011 LINDEX TOTAL 00011548
548 LINDEX TOTAL 00011548
TOTALISERS
00002 LGO 00002161
161 LGO 00002161
00003 LFOD 00003827
827 LFOD 00003827
GENERAL
PRODUCTS
4.3.2 Sub-menu MEMORISATION
You can read all the measurement results stored by the MICROCOMPT+. That can be done in two ways:
COMPLETE LIST: Display all the measurement details recorded, from the newest to the oldest, sorted by day then by measurement number.
DAY SELECTION: Display a specific measurement by selecting the day number and the measurement number.
For each measurement, you can read:
� The name of the product
� The volume in metering conditions (Vm)
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 12/39
This document is available on www.alma-alma.fr
� The converted volume (Vb)
� The product density
� The mean temperature of the measurement
� The measurement start time
� The measurement end time
� The index before measurement
� The index after measurement
Example:
MEMORISATION COMPLETE LIST
DAY SELECTION
004207REFERENCE
172DAY OF THE YEAR
016MEASUREMENT No
XXXDAY OF THE YEAR
YYYMEASUREMENT No
004207REFERENCE
21.06.18DATE (DD.MM.YY)
172MEASUREMENT No
998 LPRODUCT GO
+21.8 °CMEAN TEMPERATURE
993 LCONVERTED VOLUME
0830.0 kg/m3
DENSITY
14:59START TIME
15:06END TIME
LINDEX B00002196
LINDEX A00003406
4.4 Menu MAINTENANCE (Not used)
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 13/39
This document is available on www.alma-alma.fr
4.5 List of alarms
SATURATION MEMOIRE Saturation du journal métrologique
DISPLAY MEANING ACTION
BLO
CK
ING
MEMORY LOST (PILE)
MEMORY LOST
COEFFICIENTS FAULT
PROM FAULT
RAM FAULT
EEPROM MEMORY LOST
Perte de la mémoire secourue
Perte du journal métrologique
Ecart entre coefficients PD/GD supérieur à 0,5%
Perte de l’intégrité du logiciel ou du résident
Défaut de la mémoire secourue
Perte de la configuration métrologique
Remplacement de la pile de sauvegarde
Modification du coefficient petit débit (K1)
Remplacement de la carte AFSEC+
TOTALISER LOST
DISPLAY FAULT
WATCHDOG FAULT
TEMPERATURE FAULT
Loss of totalizer
Problem with display card
Fault with display or power card or AFSEC+ card
Temperature determination failure
If steady alarm, substitution of the display card
If steady alarm, substitution of the faulty card
Substitution of the backup battery
If steady alarm, see a reparator for trouble shooting
HIGH FLOW FAULT High flowrate (greater than maximum flowrate)
ZERO FLOW DEFAULT
POWER SUPPLY PROBLEM
LOW FLOW FAULT
METERING PROBLEM
STOP OPERATION
Zero flow
Power outage during operation
Low flowrate (less than 15m3/h)
Metering problem with the measuring device
Intentional interruption of operation
Check the hydraulic system (security valve)
Check the cause / Restore power supply
Check the hydraulic system (valve, strainer, nozzle…)
Check if the pulse transmitter is powered (red indicators)
Continue or finish the operation
Check the hydraulic system (valve, pumping…)
US
ER
Remplacement de la pile de sauvegarde
Remplacement de la carte AFSEC+
Remplacement de la carte AFSEC+
Remplacement de la carte AFSEC+
MEMORY OVER LOADED Perte de la date et de l’heure Saisir la date et l’heure en mode métrologique
DATE AND TIME LOST Loss of date and time Set date and time in supervisor mode (supervisor key)
LEAKAGE FAULT Counting outside a measurement period Check the tighness of the loading valve
NO
N B
LO
CK
ING
RE
PA
RA
TO
RCOMMUNICATION FAULT Communication with the printer lost Check the connection cable, on-off switch and fuse
VOLUME CONVER FAULT Problem during conversion of volume If steady alarm, substitution of the AFSEC+ electronic card
AUTHORIZATION LOST No more loading authorisation Check the reason on the control device
EMERGENCY STOP An emergency stop is detected Check the emergency stop
DENSITY DEFAULT Density out of range Check the metrological configuration
TEMPERATURE ATEX Temperature of the pump is out of range If steady alarm, see a reparator for trouble shooting
DIARY FAULT Reset of the events diary Acknowledge the alarm, check the date in supervisor mode (supervisor key)
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 14/39
This document is available on www.alma-alma.fr
5 SET THE FMS OEM MTP: SUPERVISOR MODE
TIME ADJUSTMENT
PARAMETERS
PRODUCT SETTINGS
CALIBRATION/GAUGE
PRINTER SETTINGS
ICOM MENUS See ANNEX 1
LANGUAGE
5.1 Menu CALIBRATION/ GAUGE
CALIBRATION/GAUGE ENTER CALIBRATION
LINEARISATION/FLOW
5.1.1 Menu ENTER CALIBRATION
This menu is used to do a check of the accuracy of the measuring system. The MICROCOMPT+ calculates the measuring device error, the new corrected coefficient and the average flow.
First, fill the gauge (USER mode) in high or low flow with predetermination of the volume.
Switch to SUPERVISOR mode, select CALIBRATION/GAUGE>ENTER CALIBRATION and validate.
Enter the volume read on the gauge and validate. The MICROCOMPT+ displays the information that follows:
� The signed error in %
� The coefficient revised as a function of the error
� The average flow of the delivery.
001000 LENTER VOLUME (REF)
-00.33ERROR (PERCENT)
09.9668COEFFICIENT
ENTER CALIBRATION
27.3MEAN FLOWRATE
L kg/m3
/min /h
+0.00 °CMEAN TEMPERATURE
NORMAL
REGULATION
LOW FLOW REGULATION
5.1.2 Sub-menu LINEARISATION/FLOW
This menu is used to make a flow-correction for two measuring points (at low and high flowrate). The MICROCOMPT+ stores flowrate and coefficient calibrated values in order to define both correction points: at low and high flowrate.
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 15/39
This document is available on www.alma-alma.fr
When you validate the menu LINEARISATION/FLOW, the calibrated values are displayed; you need to unseal the MICROCOMPT+ to switch in METROLOGICAL mode and record the values via the EMA (PUMP MODE)>METER COEFFICIENT menu.
To linearize the curve, two tests are necessary:
� Fill the gauge in high flow [flowmin×3]≤high flow<[flowmax], and enter the volume read on the gauge in the menu CALIBRATION/STANDARD>ENTER CALIBRATION as described above
� Fill the gauge in low flow [flowmin]≤flow<[flowminx×2], and enter the volume read on the gauge in the menu CALIBRATION/STANDARD>ENTER CALIBRATION
� Select CALIBRATION/GAUGE>LINEARISATION/FLOW and validate. It is then possible to see the coefficients and the flow rates data for the two tests carried out.
LINEARISATION/DEBIT 09.9890COEFFICIENT PD (K1)
09.9845COEFFICIENT GD (K2)
5.3PETIT DEBIT
L kg/m3
/min /h 29.6GRAND DEBIT
L kg/m3
/min /h
If the procedure failed, the MICROCOMPT+ can display the information that follows:
� LARGE GAP K1/K2: Correction between both measuring points >0.5%
� FLOWS TOO CLOSE: High flowrate value is out of range. It needs to be: [flowmin×3]≤high flow<[flowmax].
� LO-FLOW OUT OF RANGE: Low flowrate value is out of range. It needs to be: [flowmin]≤low flow≤[flowmin×1.5]
� ONLY ONE GAUGE: One of the tests has not been done (at low or high flowrate)
� NO VALID GAUGE: Both tests have not been done (at low and high flowrate)
When the procedure is completed, the MICROCOMPT+ displays the sequence that follows:
CONFIRM COEFFICIENTS REMOVE THE SEAL PUT BACK THE SEAL
The new coefficient and flow rates values are taken into account.
5.2 Menu LANGUAGE
Select the display language. This menu is available if a translation catalogue is uploaded in the MICROCOMPT+.
LANGUAGE (EN) LANGUAGE�EN
LANGUAGE�FR
5.3 Menu PRODUCT SETTINGS
PRODUCT SETTINGS 1CHOOSE PRODUCT
16CHOOSE PRODUCT
You can configure the parameters that follow for a maximum of 16 products:
NAME: Record the name of the product. Default name for product 1: GO, and for product 2: FOD
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 16/39
This document is available on www.alma-alma.fr
DENSITY: Show the product density at 15°C in Kg/m3 (MV15).
CORRECTION: Show if the correction is “ON” or “OFF” for the product (see METROLOGICAL>EMA>PRODUCT CORRECTION).
Example for product 1:
1CHOOSE PRODUCT
01/NAME/GO 01/NAME/GO
0830.0 kg/m3
01/GO /DENSITY
01/CORRECTION (OFF)
5.4 Menu PRINTER SETTINGS
Choose the ticket format for printing of the delivery ticket.
PRINTER SETTINGS TICKET (XX) TICKET�DEFAULT
5.5 Menu TIME ADJUSTMENT
Date and time are set in METROLOGICAL mode. You can adjust time (±2h) one time a day. Use French format, for example: 14.41 means 2.41 pm.
TIME ADJUSTMENT 14.41TIME (HH:MM)
5.6 Menu PARAMETERS:
This menu shows the parameters set in METROLOGICAL mode.
PARAMETERS INDICATOR REFERENCE
CONFIGURATION
MEASURING SYSTEM
5.6.1 Sub-menu INDICATOR REFERENCE
See the METROLOGICAL mode section for meaning of the parameters.
000000INDICATOR REFERENCE
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 17/39
This document is available on www.alma-alma.fr
5.6.2 Sub-menu CONFIGURATION
See the METROLOGICAL mode section for meaning of the parameters.
CONFIGURATION PRESET (XX)
123456 LUNIT AND ACCURACY
CONVERSION (ON)
AUTHORIZATION (XX)
PRINTER (XX)
+15.0 °C
REFERENCE TEMP.
DISPLAY (XX)
+15.0 °C
DENSITY REF. TEMP
FORMULA (XX)
DENSITY RANGE 0500.0 kg/m3
MINIMUM DENSITY
0999.9 kg/m3
MAXIMUM DENSITY
CONVERSION�ON
FLOWING (XX)
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 18/39
This document is available on www.alma-alma.fr
5.6.3 Sub-menu MEASURING SYSTEM
See the METROLOGICAL mode section for meaning of the parameters.
MEASURING SYSTEM METER COEFFICIENT 00.0000COEFFICIENT LF (K1)
000.0LOW FLOW/K1 (Q1)
L kg/m3
/min /h
00.0000COEFFICIENT HF (K2)
000.0HIGH FLOW/K2 (Q2)
L kg/m3
/min /h
+0CORRECTION/ THOUSAND
TEMPERATURE (ON) +15.9 °CPRODUCT TEMPERATURE
-20.0 °CMINIMUM TEMPERATURE
+50.0 °CMAXIMUM TEMPERATURE
SETTINGS FLOWRATE SETTINGS 008.0MINIMUM FLOWRATE
kg/m3
/h
L kg/m3
min /h 050.0MINIMUM FLOWRATE
VOLUME SETTINGS
10 LLF�HF VOLUME
100LHF�LF VOLUME
200LMINIMUM DISCHARGE
TIMING SETTINGS
+01.0PULSES OUTPUT
TEMPERATURE�ON
0200 FLOW TIMING (S)
5.7 Menu ICOM MENUS
See the ANNEX 1: Features of the connected MICROCOMPT+.
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 19/39
This document is available on www.alma-alma.fr
6 CONFIGURE THE FMS OEM MTP: METROLOGICAL MODE
MEASURING SYSTEM
CONFIGURATION
INDICATOR REFERENCE
DATE AND TIME
6.1 Menu INDICATOR REFERENCE
Record the MICROCOMPT+ serial number (alphanumeric value).
000000ENTER REFERENCE
000000INDICATOR REFERENCE
6.2 Menu CONFIGURATION
CONFIGURATION PRESET
UNIT AND ACCURACY
PRODUCTS
CONVERSION
PRINTER
FLOWING
AUTHORIZATION
6.2.1 Sub-menu PRESET
PRESET�ON: The user can choose to preset the volume or not (free mode)
PRESET�OFF: Preset is not available in USER mode.
PRESET (XX) PRESET�ON
PRESET�OFF
6.2.2 Sub-menu UNIT AND ACCURACY
Choose the unit and the accuracy of the quantity that is displayed and printed. This menu is different with or without conversion.
UNIT AND ACCURACY 123456 LUSAGE UNIT
123.4FLOWRATE UNIT
L kg/m3
/min /h
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 20/39
This document is available on www.alma-alma.fr
6.2.2.1 With CONVERSION�OFF
USAGE UNIT: Choose the unit and the accuracy of the quantity displayed and printed. Enter a generic quantity: volume (L or m3), mass (kg) or no defined unit. If you choose the unit ‘kg’ or no defined unit, the MICROCOMPT+ counts scale intervals.
For example: with a mass flow meter, choose the unit ‘kg’ or no defined unit. And affix close to the display a label with the unit ‘t’ for tons.
Quantity in litre
Quantity in m3
Quantity in m3 with précision 10
-1
Quantity in m3 with précision 10-2
Quantity in kg
Quantity with no defined unit
123456 LUSAGE UNIT
123456LUSAGE UNIT
123456 m3
USAGE UNIT
123456 kgUSAGE UNIT
- - - - - -USAGE UNIT
12345.6 m3
USAGE UNIT
1234.56 m3
USAGE UNIT
FLOWRATE UNIT: Choose the unit of the flow rate that will be displayed and printed. Flowrate units depends on the choice made for the usage unit (scale interval/minute or kilo-scale interval/hour).
Usage unit: L or m3 or undefined
123.4FLOWRATE UNIT
L kg/m3
/min /h 123.4FLOWRATE UNIT
L kg/m3
/min /h
1234FLOWRATE UNIT
L
/min
Usage unit: Kg
123.4FLOWRATE UNIT
L kg/m3
/min /h 123.4FLOWRATE UNIT
L kg/m3
/min /h
1234FLOWRATE UNIT
L kg/m3
/min /h
tons/h, (the pictogram for ton is not displayed
6.2.2.2 With CONVERSION�ON
USAGE UNIT: Choose the unit and the accuracy of the quantity displayed and printed. Enter a generic quantity: volume (L or m3), mass (kg) or no defined unit. If you choose the unit ‘kg’ or no defined unit, the MICROCOMPT+ counts scale intervals.
For example: with a mass flow meter, choose the unit ‘kg’ or no defined unit. And affix close to the display a label with the unit ‘t’ for tons.
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 21/39
This document is available on www.alma-alma.fr
Quantity in litre
Quantity in m3
Quantity in m3 with précision 10-1
Quantity in m3 with précision 10-2
Quantity with no
defined unit
123456 LUSAGE UNIT
123456LUSAGE UNIT
123456 m3
USAGE UNIT
- - - - - -USAGE UNIT
12345.6 m3
USAGE UNIT
1234.56 m3
USAGE UNIT
FLOWRATE UNIT: Choose the unit of the flow rate that will be displayed and printed.
123.4FLOWRATE UNIT
L kg/m3
/min /h 123.4FLOWRATE UNIT
L kg/m3
/min /h
1234FLOWRATE UNIT
L
/min
6.2.3 Sub-menu PRODUCTS
You can configure the parameters that follow for a maximum of 16 products: For each product: density is displayed and you can change the value if conversion is on (CONVERSION�ON). Products name is set in SUPERVISOR mode. To apply correction, validate CORRECTION�ON.
PRODUCTS 1CHOOSE (GO)
0830.0 kg/m3
DENSITY
01>CORRECTION (XX) CORRECTION�OFF
CORRECTION�ON
0830.0 kg/m3
DENSITY
2CHOOSE (FOD)
0730.0 kg/m3
DENSITY
02>CORRECTION (XX) CORRECTION�OFF
CORRECTION�ON
0730.0 kg/m3
DENSITY
NNCHOOSE ( )
0750.0 kg/m3
DENSITY
NN>CORRECTION (XX) CORRECTION�OFF
CORRECTION�ON
0750.0 kg/m3
DENSITY
NN=03 to 16
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 22/39
This document is available on www.alma-alma.fr
6.2.4 Sub-menu CONVERSION
The FMS OEM MTP can operate with conversion or without conversion.
CONVERSION (XX) CONVERSION�OFF
CONVERSION�ON When conversion is on, you must configure the parameters that follow:
MAIN DISPLAY: Select the type for displayed quantity (VM: volume in metering conditions, VB: volume converted to the reference temperature).
REFERENCE TEMP.: Non editable value. Shows the reference temperature used for conversion: 15°C
DENSITY REF TEMP: Non editable value. Shows the reference temperature for densities: 15°C
FORMULA: The choice of the conversion formula causes an implicit definition of valid density and temperature ranges to guarantee the conversion result. See the table below to select the conversion table that corresponds to the products:
Product Conversion formula
Crude products API54A Refined products API54B LPG and bitumen LPG Blended biofuels EN14214 Ethanol at 15°C ETH15 Ethanol at 20°C ETH20 Fatty acid methyl esters FAME Ethyl tertio butyl ether ETBE
DENSITY RANGE: Enter the minimum and maximum density limits laid down by the owner to control the product quality. The density unit is Kg/m3.
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 23/39
This document is available on www.alma-alma.fr
CONVERSION�ON
+15.0 °C
REFERENCE TEMP.
DISPLAY (XX) DISPLAY�VM
DISPLAY�VB
+15.0 °C
DENSITY REF. TEMP
FORMULA (XX) FORMULA�API54A
FORMULA�API54B
FORMULA�GPL
FORMULA�EN 14214
FORMULA�ETH15
DENSITY RANGE 0500.0 kg/m3
MINIMUM DENSITY
0999.9 kg/m3
MAXIMUM DENSITY
0500.0 kg/m3
MINIMUM DENSITY
FORMULA�ETH20
FORMULA�EMHV
FORMULA�ETBE
0999.9 kg/m3
MAXIMUM DENSITY
6.2.5 Sub-menu PRINTER
PRINTER (XX) PRINTER�OFF
PRINTER�ON If the FMS OEM MTP operates with a printer, select the menu PRINTER�ON. Then, you can configure the parameters that follow:
AUTO PRINT�ON: The delivery ticket is automatically printed at the end of the measuring operation.
AUTO PRINT�OFF: The delivery ticket is not automatically printed. You must push OK to print or CLEAR to cancel.
PRINTER�ON PRINTING�MANU
PRINTING�AUTO
6.2.6 Sub-menu FLOWING
Flowing starts automatically or manually by pressing the push button.
FLOWING (XX) FLOWING�MANU
FLOWING�AUTO
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 24/39
This document is available on www.alma-alma.fr
6.2.7 Sub-menu AUTHORIZATION
The FMS OEM MTP operates with an external authorization or not.
AUTHORIZATION AUTHORIZATION�OFF
AUTHORIZATION�ON
6.3 Menu MEASURING SYSTEM
MEASURING SYSTEM
CORRECTION/ THOUSAND
METER COEFFICIENT
PULSES OUTPUT
TEMPERATURE
SETTINGS
6.3.1 Sub-menu METER COEFFICIENT
Enter the coefficient of the measuring system meter (pulses/liter).
LF COEFFICIENT (K1): Coefficient for low flow (pulses/liter)
LOW FLOW/K1 (Q1): Low flow reference (m3/h)
HF COEFFICIENT (K2): Coefficient for high flow (pulses/liter)
HIGH FLOW/K2 (Q2): High flow reference (m3/h)
00.0000COEFFICIENT LF (K1)
METER COEFFICIENT 00.0000COEFFICIENT LF (K1)
000.0LOW FLOW/K1 (Q1)
L kg/m3
/min /h 000.0LOW FLOW/K1 (Q1)
L kg/m3
/min /h
00.0000COEFFICIENT HF (K2)
00.0000COEFFICIENT HF (K2)
000.0HIGH FLOW/K2 (Q2)
L kg/m3
/min /h 000.0HIGH FLOW/K2 (Q2)
L kg/m3
/min /h
6.3.2 Sub-menu CORRECTION/ THOUSAND
Record the correction factor per thousand (‰) of the FMS OEM MTP for a measurement with low viscosity products. See the marking of the turbine meter or see the ALMA calibration certificate. See the verification manual MV 5015 for further information.
+0CORRECTION
+0CORRECTION/ THOUSAND
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 25/39
This document is available on www.alma-alma.fr
6.3.3 Sub-menu PULSES OUTPUT
Record the number of pulses per liter that corresponds to the quantity of liquid that the MICROCOMPT+ counts.
+01.0PULSES OUTPUT
+01.0PULSES OUTPUT
6.3.4 Sub-menu TEMPERATURE
This menu is an option. It is used to calibrate the temperature into the MICROCOMPT+. See maintenance sheet FM 8510.
TEMPERATURE (XX) TEMPERATURE�OFF
TEMPERATURE�ON +99.9 °CPRODUCT TEMPERATURE
+99.9 °CCALIBRATION
-20.0 °CMINIMUM TEMPERATURE
-20.0 °CMINIMUM TEMPERATURE
+50.0 °CMAXIMUM TEMPERATURE
+50.0 °CMAXIMUM TEMPERATURE
6.3.5 Sub-menu SETTINGS
SETTINGS
VOLUME SETTINGS
FLOWRATE SETTINGS
TIMING SETTINGS
6.3.5.1 Flowrate settings
You can set the flowrate parameters that follow:
MINIMUM FLOWRATE: Record the metrological minimum flowrate of the FMS OEM MTP in m3/h or l/min. You can select the flow unit in the menu CONFIGURATION>UNIT AND
ACCURACY.
MAXIMUM FLOWRATE: Record the metrological maximum flowrate of the FMS OEM MTP in m3/h or l/min. You can select the flow unit in the menu CONFIGURATION>UNIT
AND ACCURACY.
FLOWRATE SETTINGS
050.0ENTER MAXIMUM FLOW
L kg/m3
/h
008.0ENTER MINIMUM FLOW
L kg/m3
/h 008.0MINIMUM FLOWRATE
kg/m3
/h
L kg/m3
min /h 050.0MAXIMUM FLOWRATE
6.3.5.2 Volume settings
MINIMUM QUANTITY: Record the minimum quantity of the FMS OEM MTP in liters. This value is given by the association of the turbine meter, the MICROCOMPT+ and other parts of the FMS OEM MTP.
LF�HF VOLUME: Enter the volume beyond which the MICROCOMPT+ switches from low to high flowrate.
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 26/39
This document is available on www.alma-alma.fr
HF�LF VOLUME: Enter the volume beyond which the MICROCOMPT+ drives the low flowrate at the end of a preset measurement.
VOLUME SETTINGS
10 LLF�HF VOLUME
000010 LLF�HF VOLUME
100LHF�LF VOLUME
000100LHF�LF VOLUME
200LMINIMUM DISCHARGE
000200LMINIMUM DISCHARGE
6.3.5.3 Timing settings
You can set the timing parameters that follow:
0 FLOW TIMING (S): Enter the maximum time before starting of flow (in minutes). Enter zero to disable the timeout.
TIMING SETTINGS 0200 FLOW TIMING (S)
0200 FLOW TIMING (S)
6.4 Menu DATE AND TIME
Record the date. Then record the time at French format and validate (e.g. 14.41 means 2.41 pm).
DATE AND TIME 14.41TIME (HH:MM)
24.06.18DATE (JJ.MM.AA)
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 27/39
This document is available on www.alma-alma.fr
ANNEX 1: FEATURES OF THE CONNECTED MICROCOMPT+
1. GENERAL PRESENTATION
The connected functions of the MICROCOMPT+ are:
� Incoming data flow processing
� Management of the communication modules below
� Updating of the app, tickets and language catalogues as far as the MICROCOMPT+ has been switched into METROLOGICAL mode.
Communication modules are listed below:
� Wi-Fi (IEEE 802.11 b/g/n (2.4GHz) OR Bluetooth Low Energy 4.1
� GSM (2G, 3G, 4G) / GPS
� RFID NFC allowing the reading of an RFID key to switch in SUPERVISOR mode
� Ethernet Base 10/100
The wireless connection enables the MICROCOMPT+ to communicate with an embedded computer or with a PC/tablet/portable device, in hazardous area (ATEX).
The GSM module associated to the GPS navigation system allows the device tracking. Two antennas are located outside the MICROCOMPT box.
Three tricolor LED on the MICROCOMPT+ front face are showing the wireless connection status as described in the table below:
Left-hand LED: Wi-Fi or Bluetooth
Middle LED: GSM / GPS
Right-hand LED: NFC (RFID)
Steady light:
• Blue* / Cyan*: Connection OK
• Red: Waiting for initialization Flashing light:
• Blue / Cyan slow flashing: Waiting for connection
• Blue / Cyan rapid flashing: Communication in progress
• Red: Initialization error
Steady light:
• Purple: Waiting for internet connection
• White: Internet connection OK
• Red: Waiting for initialization Flashing light:
• White: Transfer in progress • Red every 2 seconds:
Coordinates not found • Green every 2 seconds: GPS
OK
• Red: Initialization error
Flashing light:
• Green: Authentication of the RFID key OK
• Red: Authentication error of the RFID key
• Green/ Red: RFID key not accepted, but authentication is ok
(*): Blue: Bluetooth; Cyan: Wi-Fi
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 28/39
This document is available on www.alma-alma.fr
2. MENU SUPERVISOR>ICOM
User RFID key – Blue – Level 1
This key is associated to a single MICROCOMPT+. It is used to switch into SUPERVISOR mode to access the ICOM menu.
Manager RFID key – Green – Level 2
Many of these keys can be associated to a single MICROCOMPT+. Likewise, a single key can be associated to one or many MICROCOMPT+.
RFID key is used to switch into SUPERVISOR mode to access the ICOM menu. Specific menus are available that allow the manager to configure the MICROCOMPT+ for its communication with the external environment. The specific menus are indicated by green boxes within the document.
Maintenance RFID key – Red – Level 3
This key doesn’t need to be associated to the MICROCOMPT+. It is used to switch into SUPERVISOR mode to access the ICOM menu. Specific menus are available that allow the maintenance operator to change parameters. The specific menus are indicated by red boxes within the document.
CALIBRATION / JAUGE
LANGUE (XX)
REGLAGE HEURE
ICOM
...
CLE RFID
MISE A JOUR
ETHERNET
GSM
BLUETOOTH
GPS
WI-FI
CANBUS
INCLINOMETRE
INFO I-COM
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 29/39
This document is available on www.alma-alma.fr
2.1. Menu UPDATE
The MICROCOMPT+ connects to the server via Wi-Fi, Bluetooth, Ethernet or GSM.
MISE A JOUR SYNCRO SERVEUR (*)
(*) EN COURS / xx NOUV. MISE A JOUR / AUCUNE MISE A JOUR
SELECT APPLI XXXXX.MOT
SELECT LOT TICKET
SELECT LANGUE
XXXXX.MOT
XXXXX.MOT
FICHIER SELECT.
FICHIER SELECT.
FICHIER SELECT.
Maintenance
SYNC FROM SERVER: Synchronization of the updated files from ALMA server. If an update of the functions or the communication configuration is uploaded, it will be applied on the next reboot of the MICROCOMPT+.
SELECT APPS FILE(*) – Access restricted to the Maintenance: Used to display and select the version(s) of the application available on the SD card. NO FILE is displayed if there’s no file to download.
SELECT TICKET FILE(*) – Access restricted to the Maintenance: Used to display and select the version(s) of the application available on the SD card. NO FILE is displayed if there’s no file to download.
SELECT LANG FILE(*) – Access restricted to the Maintenance: Used to display and select the version(s) of the application available on the SD card. NO FILE is displayed if there’s no file to download.
(*) Selected files are automatically downloaded onto the AFSEC board when switching the MICROCOMPT+ into ‘Resident’ mode. See the operating manual MU 7037 (§2).
2.2. Menu RFID KEY
CLE RFID INFO NIV: X NUM: Y
GERER CLE RFID CLE BLEU
CLE VERTE
POSER LA NOUV. CLESYNC CLE
AJOUTER CLE
SUPPR. CLE
POSER LA NOUV. CLE
SUPPR. CLE : X
Gestionnaire
INFO: Display of the level and the identifier of the RFID key (Level 1/Blue/User, Level 2/Green/Manager, Level 3/Red/Maintenance)
MANAGE RFID KEY – Access restricted to the Manager:
BLUE KEY: Used to associate a user RFID key to the MICROCOMPT+
GREEN KEY: Used to associate a manager RFID key to the MICROCOMPT+ or to remove keys that have already been associated.
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 30/39
This document is available on www.alma-alma.fr
2.3. Menu ETHERNET
ON
OFF
ETHERNET 10/100 ETAT: (*)
DHCP: XXX
IP XXX.XXX.XXX.XXX
MSK XXX.XXX.XXX.XXX
PASS XXX.XXX.XXX.XXX
DNS XXX.XXX.XXX.XXX
(*) CONNECTE / DECONNECTE
�299.299.299.299
�299.299.299.299
�299.299.299.299
�299.299.299.299
CONFIG
MODBUS TCP ID: XX
PORT: 1234
�254
�9999
Gestionnaire
STATE: Status of the Ethernet connection
CONFIG – Access restricted to the Manager:
DHCP: If ON is enabled, IP parameters can be initialized through the DHCP protocol. If OFF is enabled, parameters are set manually
IP: IP: eMICROCOMPT+ IP address
MSK: Subnet mask (IP mask for the internal IP address allocation)
PASS: Gateway (IP Address for the internet access of the Ethernet interface)
DNS: IP Address to access a DNS server
MODBUS TCP – Access restricted to the Manager:
ID: eMICROCOMPT+ Modbus identifier between 0 and 255
PORT: TCP/IP access port for Modbus protocol
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 31/39
This document is available on www.alma-alma.fr
2.4. Menu Wi-Fi
WI-FI ETAT: (*)
HOTES WI-FI SSID: XXX
PWD: XXX
SECU: XXX OPEN
WEP
WPA_PSK
SEC_802_1X
(*) NON DISPONIBLE (le calculateur n’est pas équipé) / DECONNECTE / CONNECTE(**) SI CONNECTE
SSID: XXX (**) NIVEAU SIGNAL : X/5 (**)
�abcdefg
ON
OFF
DHCP: XXX
IP XXX.XXX.XXX.XXX
MSK XXX.XXX.XXX.XXX
PASS XXX.XXX.XXX.XXX
DNS XXX.XXX.XXX.XXX
�299.299.299.299
�299.299.299.299
�299.299.299.299
�299.299.299.299
CONFIG
MODBUS TCP ID: XX
PORT: 1234
�254
�9999
�ABCDEFG
Gestionnaire
STATE: Status of the Wi-Fi connection. If connection is successful, you can do a check of SSID and quality
WI-FI HOST: Set the characteristics of the wireless network access point
SSID: 32 characters-alphanumeric key that identifies the wireless network uniquely
SECU: Type of security protocol for the network
OPEN: Free Wi-Fi
WEP: Encryption protocol by a key encoded in 64 or 128 bits
WPA_PSK: Encryption protocol by a 128 bits-dynamic key
SEC_802-1X: Encryption protocol compatible with the standard IEEE 802.1X
PWD: Network password. Permitted character: <space>!"#$%&'()*+,-./
0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~<DEL> (See §3 visualization on the MICROCOMPT+ display)
DHCP: If ON is enabled, IP parameters can be initialized through the DHCP protocol. If OFF is enabled, parameters are set manually
IP: IP: eMICROCOMPT+ IP address
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 32/39
This document is available on www.alma-alma.fr
MSK: Subnet mask (IP mask for the internal IP address allocation)
PASS: Gateway (IP Address for the internet access of the Ethernet interface)
DNS: IP Address to access a DNS server
MODBUS TCP – Access restricted to the Manager:
ID: eMICROCOMPT+ Modbus identifier between 0 and 255
PORT: TCP/IP access port for Modbus protocol
2.5. Menu BLUETOOTH
BLUETOOTH
NOM : XXX
ETAT: (*)
�ABCDEFG
(*) NON DISPONIBLE (le calculateur n’est pas équipé) / DECONNECTE / CONNECTE
MODBUS RTU ID: XX �254
Gestionnaire
STATE: Status of the Bluetooth connection
NAME – Access restricted to the Manager: Set the connection name
MODBUS RTU – Access restricted to the Manager:
ID: Modbus identifier via Bluetooth (between 1 and 254)
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 33/39
This document is available on www.alma-alma.fr
2.6. Menu GSM
GSM XG YYY
SYSTEME WEBGRIF URL: XXX.YYYY.ZZ
APN: XXX
(*) PAS DE SIGNAL ou 2G 3G 4G + FOURNISSEUR D’ACCES (**) SI CONNECTE
NIVEAU SIGNAL : X/5 (**)(*)
�ABCDEFG
PORT: XXX �9999
LOG: XXX
PWD: XXX
AUTRES SYSTEMES URL: XXX.YYYY.ZZ
PORT: XXX �9999
LOG: XXX
PWD: XXX
GPS PERIODE: XX S �999
Gestionnaire
Gestionnaire
SYSTEME ALMA URL: XXX.YYYY.ZZ
PORT: XXX �9999
LOG: XXX
PWD: XXX
�ABCDEFG
�ABCDEFG
�abcdefg
Maintenance
�ABCDEFG
�abcdefg
�ABCDEFG
�ABCDEFG
�ABCDEFG
�abcdefg
XG YYY: The signal is being received: the type of mobile network is displayed (with X=2 for 2G, X=3 for 3G, and X=4 for 4G) according to the protocols GSM / GPRS / EDGE, UMTS / HSPA+ / LTE, followed by the name of the service provider. Otherwise NO SIGNAL is displayed
APN – Access restricted to the Manager: Name of the internet access point, only if ALMA does not supply it
ALMA SYSTEM – Access restricted to the Maintenance: Information of connection to the ALMA FTP server for files transfer
URL: Web address of the ALMA FTP server (host)
PORT: ALMA FTP server port, default value: 21
LOG: ALMA FTP server identifier
PWD: ALMA FTP server password. Permitted characters: <space>!"#$%&'()*+,-./
0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~<DEL> (See §3 visualization on the MICROCOMPT+ display)
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 34/39
This document is available on www.alma-alma.fr
WEBGRIF SYSTEM – Access restricted to the Manager: Information of connection to the Webgrif FTP server for files transfer
URL: Web address of the Webgrif FTP server (host)
PORT: Webgrif FTP server port, default value: 21
LOG: Webgrif FTP server identifier
PWD: Webgrif FTP server password. Permitted characters: <space>!"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~<DEL> (See §3 visualisation on the MICROCOMPT+ display)
GPS PERIOD: Backup period of GPS coordinates (from 1 to 999 seconds)
OTHER SYSTEM – Access restricted to the Manager: Information of connection to the FTP server for files transfer
URL: Web address of the FTP server (host)
PORT: FTP server port, default value: 21
LOG: FTP server identifier
PWD: FTP server password. Permitted characters: <space>!"#$%&'()*+,-./
0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~<DEL> (See §3 visualization on the MICROCOMPT+ display)
2.7. Menu GPS
GPS ETAT: (*)
(*) PAS DE SIGNAL / 2DFIX / 3DFIX
LAT: 11.222222 LONG: 33.444444 NB SAT: 99
STATE: The signal is being received: the type of signal is displayed 2DFIX or 3DFIX. Validating the data makes the GPS coordinates appear (latitude then longitude), and lastly appears the number of satellites which signals are simultaneously received (that gives information about the position accuracy). Otherwise NO SIGNAL is displayed.
2.8. Menu CANBUS
CANBUS ETAT: (*)
VITESSE: X KBIT/S 1000
CANOPEN ID: XX
800
250
125
(*) CONNECTE / DISCONNECTE(**) ENTRE 1 ET 127
�127
Gestionnaire
STATE: Status of the CANBus connection
SPEED – Access restricted to the Manager: Speed of the CANBus connection
CANOPEN – Access restricted to the Manager:
ID: Identifier for the CANopen protocol (between 1 and 127)
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 35/39
This document is available on www.alma-alma.fr
2.9. Menu INCLINOMETER
INCLINOMETRE PENTE : XX, X° ROULIS : XX, X° X,XX Y,YY Z,ZZ
CALIBRER ANGLES
Maintenance PITCH…: Used to display the bank angles of the truck and the inclinometer raw data
CALIBRATE ANGLES – Access restricted to the Maintenance: Used to reset the angles ‘pitch’ and ‘roll’ when the truck has a horizontal position in order to correct the assembly tolerances of the MICROCOMPT+ on the truck.
2.10. Menu I-COM INFO
INFO I-COM 446_VX.XX.XX_AA
REDEMARRER LES COM
Gestionnaire
447_VX.XX.XX_AA
446_V…: Software’s number and version
REBOOT COM – Access restricted to the Manager: Reset of the ‘interface com’ board.
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 36/39
This document is available on www.alma-alma.fr
3. VIZUALISATION OF THE PERMITTED CHARACTERS ON THE MICROCOMPT+
Visualization of the permitted characters on the MICROCOMPT+ display:
<SPACE> ! " # $ % & ‘ ( ) * + , - . /
0 1 2 3 4 5 6 7 8 9 : ; < = > ?
@ A B C D E F G H I J K L M N O
P Q R S T U V W X Y Z [ \ ] ^ _
` a b c d e f g h i j k l m n o
p q r s t u v w x y z { | } ~ <DEL>
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 37/39
This document is available on www.alma-alma.fr
ANNEX 2: PRINTINGS
SUMMARY: PARAMETERS:
FMS OEM 4048VERSION 01.02.05 DATED 20.12.18PRINTED ON THE 26.12.18 AT 11:37INDICATOR: 04027
SUMMARY OF DELIVERIES OF 26.12.18DAY 360 - 003 MEMORISED RESULTS
**** DAILY TOTALISERS ****
GO (01) : 00000998 L +13.0°CFOD (02) : 00002408 L +13.0°C
TOTAL FROM 1 TO 2 : 00003406 L +13.0°C
********** SUMMARY **********START END MESU (L) (°C)TIME TIME No. PROD VM TEMP09:40 09:50 01 GO 00998 +12,9 09:51 10:01 02 FOD 01198 +12,910:02 10:23 03 FOD 01210 +12,9
FMS OEM 4048VERSION 01.02.05 DATED 20.12.18PRINTED ON THE 26.12.18 AT 15:30
INDICATOR: 04027
************* PARAMETRES *****************
INDICATEUR : 004027UNITE ET PRECISION : 123456 LCONVERSION : OUIAFFICHAGE : VMIMPRIMANTE : OUIINFO EMBARQUEE : NONENSEMBLE DE MESURAGE:COEFFICIENT PD (K1) : 10.0000 IMP/LPETIT DEBIT/K1 (Q1) : 0.0 M3/h COEFFICIENT GD (K2) : 10.0000 IMP/L
GRAND DEBIT/K2 (Q2) : 0.0 M3/h
CORRECTION : 0TEMPERATURE EM : OUITEMPERATURE PRODUIT : 21.8°CTEMPERATURE MIN : -20.0°CTEMPERATURE MAX : 50.0°C
************* PRODUITS *****************
LIBELLE MASSE VOLUMI CORRECTIONGO 0830.0 KG/M3 NONFOD 0730.0 KG/M3 NON
************* CONSIGNES ***************DEBITS:DEBIT MINIMAL : 8.0 M3/HDEBIT MAXIMAL : 50.0 M3/HVOLUME:QUANTITE MINIMALE : 200 LVOLUME PD�GD : 10 LVOLUME GD�PD : 100 LTEMPS:TEMPO DEBIT 0(S) : 20
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 38/39
This document is available on www.alma-alma.fr
TOTALISERS: EVENTS RECORDED:
********** TOTALISERS**********
GENERAL TOTALISER : 00004358 L
GO (01) : 00001950 L FOD (02) : 00002408 L
TOTAL : 00004358 L
FMS OEM 4048VERSION 01.02.05 DATED 20.12.18PRINTED ON THE 26.12.18 AT 18:17
INDICATOR: 04027
28 RECORDING(S)
11:33:33 STOP OPERATION...
09:47:25 PARAM@ 1= 009:47:15 PARAM@ 55= 8109:47:06 PARAM@ 53= 108:59:02 METROLOGICAL MODE 08:58:57 SWITCH ON
FMS OEM 4048VERSION 01.02.05 DATED 20.12.18PRINTED ON THE 26.12.18 AT 11:45INDICATOR: 04027EVENTS ON 25/07/18
DELIVERY TICKET (according to customer):
Date 26/12/18 at 15:51
Delivery product: GO
Index 001 before 00000299 at 11:35Index 002 after 00000601 at 11:42
Volume at temperature : 00302 litresVolume at 15°C : 00300 litresTemperature : +20.0°CDensity at 15°C :800.0 Kg/m3
Only the volume and mean temperature indications displayed by the indicator shall be deemed valid.
FORM DOC 120 A
MU 7111 EN A
FUEL METERING SYSTEM FMS OEM MTP Page 39/39
This document is available on www.alma-alma.fr
RELATED DOCUMENTS
GU 7111 User Guide
MV 5015 Verification Manual
FM 8000 Replacement of the backup batteries on the AFSEC and AFSEC+ electronic board
FM 8001 Diagnostic support for power supply failure
FM 8002 Diagnostic support for a display failure
FM 8003 Diagnostic support for DEB_0 or ZERO FLOW DEFAULT alarm
FM 8005 Diagnostic support for METERING PROBLEM alarm
FM 8006 Diagnostic support for DATE AND TIME LOST alarm
FM 8007 Diagnostic support for MEMORY LOST or DEF MEMO alarm
FM 8010 Diagnostic support for EEPROM MEMORY LOST alarm
FM 8011 Configuration of jumpers and adjustment of metering thresholds on the AFSEC+ electronic board
FM 8510 Adjustment of a temperature chain in a MICROCOMPT+