7
Socrates’s experience THURSDAY, JANUARY 26, 2012 Setting up of MTNL's B450TC1 modem cum WiFi router Recently I had the opportunity to setup a B 450TC1 wireless modem cum router. Setting up is fairly straight forward & should not be a problem for anyone. To set up 1) We first open a browser & type 192.168.1.1 in the location bar. You will see a similar pop up on your screen. The User Name is admin’ and Password is also ‘admin’ after 2) Next you will see the following window

Mtnl Modem Setting

Embed Size (px)

DESCRIPTION

configuration of mtnl router

Citation preview

Page 1: Mtnl Modem Setting

Socrates’s experience

T H U R S D A Y , J A N U A R Y 2 6 , 2 0 1 2

Setting up of MTNL's B450TC1 modem cum WiFi routerRecently I had the opportunity to setup a B 450TC1 wireless modem cum

router. Setting up is fairly straight forward & should not be a problem for

anyone. To set up 

1) We first open a browser & type 192.168.1.1 in the location bar.

You will see a similar pop up on your screen. The User Name is ‘admin’ and

Password is also ‘admin’ after

2) Next you will see the following window

Page 2: Mtnl Modem Setting

3) Click on the tab ‘Interface Setup’ -> ‘Internet’

4) Make ‘Virtual Circuit’ as ‘PVC 0’

5) Make ‘Status’ as ‘Activated’

6) Make ‘VPI’ as ‘0’ and ‘VCI’ as ‘32’

7) Select ‘ISP’ as ‘PPPoA/PPPoE’

8) Type your Telephone as your ‘Username’

9) And your CA No. as your ‘Password’ (CA number is your Customer A/c

number found on your tel bill)

10) Next type TCP MSS = 1360 Bytes or leave it as 1400 (Default).

11) And type TCP MTU = 1492 Bytes.

12) Go to the bottom of the page & click on ‘Save’.

13) To enable DHCP go to 'Interface Setup'->;'LAN' and select DHCP option

These VCI & VPI I have mentioned above is basically for MTNL for the other

ISP’s in India it’s the following

Connection Name VPI VCIMTNL 0 32BSNL 0 35

Page 3: Mtnl Modem Setting

Airtel 1 32VSNL 0 33

14) If you notice ‘DNS Relay’ is set as ‘User Discovered’ ie hard coded, I would

suggest that it’s set to Auto Discovery.

15) To save click on 'Save' button at bottom of page.

16) Go to the ‘Maintenance’ tab & then on ‘Sysrestart’ (See Below)

17) Select ‘Current Settings’

18) Click on ‘Restart’

The basic ADSL modem setting are finished. To check if you are connected

to the internet in the setting of the modem/router go to the ‘Status’ tab as

seen below.

Page 4: Mtnl Modem Setting

To setup the WiFi.

.Open the router page as mentioned as before

Go to ‘Interface Setup’ ->’Wireless’ (See Below)

Make ‘Access Point’ as ‘Activated’

Add a SSID (Your Network name) of your choice but not your name of

address.

Authentication Type is selected as WPA2-PSK

Page 5: Mtnl Modem Setting

Encryption is selected as TKIP/AES

Pre shared key is the wifi password. For generating long random passwords

you can use

https://www.grc.com/passwords.htm

https://secure.pctools.com/guides/password/

For further security I would suggest using the MAC filters for which in the

above picture

Select ‘Active’

Action should be made ‘Allow Association’. And the MAC addresses of the

gadgets you want to connect to the WiFi router should be added

Lastly click on ‘Save’ then as above

Go to the ‘Maintenance’ tab & then on ‘Sysrestart’

Select ‘Current Settings’

Click on ‘Restart’

I am now presuming you know how to get your other gadgets connected to

this wifi router.

I am given to understand that this screenshots & setup is similar for UT-

Star wireless Type II & IV, Beetel Type A 410TC1m, wireless type B 450TC1

& type C 480TC1.

P O S T E D B Y S O C R A T E S A T   T H U R S D A Y , J A N U A R Y 2 6 , 2 0 1 2

5 C O M M E N T S :

 Anonymous said...

Thanks, I had to reset my modem yesterday as it was giving some trouble. I then used this post to set it up again without having to call or pay anyone :DThanks again.

1 0 : 4 2 A M , J A N U A R Y 2 9 , 2 0 1 2

 Prakhar Shukla said...

can you post a working link of the firmware you are working on?

2 : 0 7 P M , J A N U A R Y 2 9 , 2 0 1 2

Page 6: Mtnl Modem Setting

 socrates said...

Check out the second picture, it mentions which firmware ver this unit is working on. Also check the last line of the post which mentions some probable models it shares screen shots with :)

8 : 2 0 A M , J A N U A R Y 3 0 , 2 0 1 2

 Anonymous said...

Wow. This is even better than the guide on the MTNL site :D Thank You :D

7 : 3 3 P M , J A N U A R Y 3 0 , 2 0 1 2

 Anonymous said...

I cannot get through the authentication. I've tried putting different user ids and passwords but I get a pop-up window saying"The site says 450TC1"

Plz help!

9 : 3 5 P M , J U N E 0 7 , 2 0 1 2

P O S T A C O M M E N T

Subscribe to Post Comments [Atom]

<< Home

P R E V I O U S P O S T S

Samsung Galaxy Ace Useful points

How do I check the WLAN MAC address of a Nokia pho...

How to configure Netgear Wireless N150 model WGR61...

Changing your Firefox default keyword search

Email Merge thru Thunderbird

Setup instructions for MyPhoneExplorer for Samsung...

How to change password of MTNL Broadband Account

Updating a laptop with Win XP to support WPA2 WiFi...

How to configure Linksys WRT 120N wireless router

Page 7: Mtnl Modem Setting

How to enter DNS setting on your computer

A B O U T M E

SOCRATES

INDIA

V I E W M Y C O M P L E T E P R O F I L E

Subscribe to

Posts [Atom]